Tender For Construction, Commissioning Of Faecal Sludge Treatment Plant Of Capacity 18 Kld At Jugsalai Nagar Parishad, Jamshedpur (Jharkhand) And Operation And Maintenance For 5 Years
Tender Value
4.46 Crore
Estimated cost
Bid Submission
12 Oct 2026
11 days left
EMD
8.93 Lakhs
Bank guarantee accepted
Document Fee
10000
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
East Singhbum → Jharkhand
EMD Exemption
Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for Construction, Commissioning Of Faecal Sludge Treatment Plant Of Capacity 18 Kld At Jugsalai Nagar Parishad, Jamshedpur (Jharkhand) And Operation And Maintenance For 5 Years
BOQ
| Sl. No. | Item Description |
| 1 | Construction of FSTP |
| 2 | Excavation in soil by manual means (Excavation for roadway in soil using manuyal means including loading in truck for carrying of cut earth to embankment site with all lifts and leads upto 1000meters.) |
| 3 | Wet Mix Macadam (Providing, laying,spreading and compacting graded stone aggregates to WMM specification including premixing the materials with water at OMC in mechanical mix plant carriage of mixed material by tipper to site , laying in uniform layers with paver in sub-base/basecourse on well prepared surface and compacting with vibratory roller to achieve desired density. with vibratory rollar |
| 4 | Granular sub base with coarse graded material.Construction of Granular sub base by providing coarse graded material,spreading in uniform layers with moto grader on prepared surface,mixing by mix in place method with rotavator at OMC nad comapacting with vibratory rollerf to achieve desirede density,complete as per Clause 401. (ii)for grading II material |
| 5 | Cement Concrete Pavement ( Construction of un-reinforced , dowel jointed , Plain cement concrete pavement over a prepared sub base with 43 grade cement @ 400 kg per cum , coarse and fine aggregate confirming to IS: 383, maximum size of coarse aggregate not exceeding 25mm mixed in a bacthing and mixing plant as per approved mix desing , transported to site laid with a fixed or lip form paver spread compacted and finished in a continous operation including provision of contraction , expansion construction and logitutednal joints , joint filter , seperation membrane sealant primer joint sealant debonding strip dowel bar tie rod admixture as approved curing compound finishing to lines and grades as per drawing |
| 6 | Earth work in excavation in foundation trenches in ordinary soil (vide classification of soil Item-A) and disposal of excavated earth as obtained to a distance up to 50M. Including all lifts with leveling ramming the foundation trenches removing roots of trees shrubs all complete as per approved design and per building specification and direction of E\I. |
| 7 | Filling in foundation trenches and plinth in layers not exceeding 150 mm thick well watered, rammed fully compacted and fine dressed with earth obtained from excavation of foundation trenches within a lead of 50 m and lift of 1.5 m all complete as per building specification and direction of E/I (Mode of measurement compacted volume). |
| 8 | Providing coarse clean sand in filling in foundation trenches including ramming & watering in layers not exceeding 150mm thick with all leads & lifts including cost of all materials, labour, royalty & taxes all complete as per building specs.and direction of E/I. |
| 9 | Providing designation 75B brick work in C.M. (1:6) in foundation and plinth with approved quality of clean coarse sand of F.M. 2 to 2.5 including providing 10mm thick mortar joints, cost of screening materials, raking out joints to 15mm depth, curing, taxes and royalty all complete as per building specification and direction of E/I. |
| 10 | Providing designation 75B Brick work in C.M (1:6) in superstructure with approved quality of clean coarse sand of F.M. 2 to 2.5 including providing 10mm thick mortar joints, cost of screening materials, raking out joints to 15mm depth, curing, taxes and royalty all complete as per building specification and direction of E/I. |
| 11 | Providing and laying in position cement concrete of specified grade excluding the cost of cenetering and shuttering - all work upto plinth level. 1:2:4 (1 Cement :2 Coarse Sand (zone - III) : 4 graded stone aggregate 20mm nominal size). |
| 12 | 1:3:6 (1 Cement :3 Coarse Sand (zone - III) : 6 graded stone aggregate 20mm nominal size) |
| 13 | 1:4:8 (1 Cement :4 Coarse Sand (zone - III) : 8 graded stone aggregate 40mm nominal size) |
| 14 | Providing & Laying cement concrete in kerbs, steps and the like at or near ground level excluding the cost of centering, shuttering and finishing 1:1.5:3 (1 cement: 1.5 coarse sand (zone - III):3 graded stone aggregates 20mm nomibnal size) |
| 15 | Providing and fixing at or near ground level precast cement concrete in kerbs, edgings etc. as per approved pattern and setting in position with cement mortar 1:3 (1 cement : 3 coarse sand), including the cost of required centering, shuttering complete. 1:1.5:3 (1 Cement : 1.5 Coarse Sand(zone-III) : 3 graded stone aggregate 20 mm nominal size) |
| 16 | Providing and laying damp-proof course 50mm thick with cement concrete 1:2:4 (1 cement : 2 coarse sand(zoneIII) : 4 graded stone aggregate 20mm nominal size). |
| 17 | 1:1.5:3 (1 Cement : 1.5 Coarse Sand (zone - III) : 3 graded stone aggregate 20 mm nominal size) |
| 18 | 1:2:4 (1 Cement : 1 Coarse Sand (zone - III) : 3 graded stone aggregate 20 mm nominal size) |
| 19 | Reinforced cement concrete work in walls (any thickness), including attached pilasters, buttresses, plinth and string course, fillets, columns, pillars, piers abutment, post and struts etc. above plinth level up to floor five level excluding cost of centring , shuttering finishing and reinforcement: 1:1.5:3 (1 Cement : 1.5 Coarse Sand (zone - III) : 3 graded stone aggregate 20 mm nominal size) |
| 20 | Reinforced cement concrete work in beams, suspended floors , roofs having slope uot 15 degree landings, balconies, shelves, chajja, lintels, bands, plain window sills, staircase & spiral stair cases above plinth level upto floor five level excluding the cost of centering , shuttering finishing and reinforcement, with 1:1.5:3 (1 Cement : 1.5 Coarse Sand (zone - III) : 3 graded stone aggregate 20 mm nominal size)In Slab |
| 21 | Centering and Shuttering including strutting, propping etc. and removal of form for Foundation, footing, bases of columns, etc for mass concrete |
| 22 | Supply, fitting and fixing good quality well dressed and well seasoned sal wood work in chaukhats in doors, windows opening…. Including wedge over all clamps complete including application of two coats of wood preservative of approved quality on the surface butting walls and lintels all complete as per building specification and direction of E/I. |
| 23 | Supplying fitting and fixing 35mm thick solid core type non-decorative single leaf flush shutters in doors and windows with black board core blended with high quality phenol formaldehyde synthetic resin both side commercial veneered of standard make with oxidised iron fittings hinges, tower bolts, handle, cleats and sand blocks and taxes all complete as per building specification and direction of E/I. |
| 24 | Supplying fitting and fixing oxidised iron fittings of approved quality and make to doors and windows all complete as per building specification and direction of E/I 100 mm butt hinge |
| 25 | Supplying, fitting and fixing M.S. grill made of 20x6mm M.S. flat as per approved design and drawing, properly fabricated with joints continuous fillet welded and finished smooth , carriage of grill to work site, hoisting as per building specification and direction of E/l. (where materials is not supplied by the deptt.) |
| 26 | Providing and fixing fan hook of 16mm dia M.S. bar 1 metre long bent to required size and shape placed in position and fixed in R.C.C. slab/ beam at the time of casting all complete as per building specification and direction of E/I. (where material is not supplied by deppt.) |
| 27 | Supplying ,fixing and fixing collapsible gate of appoved sixe and make properly fabricated with vertical double channels 20x10x2 mm at 100 mm centres and braced with M.S flat diagonlas 20x3 mm with top and bottom rails of T iron 40x40x6 mm with 38 mm dia steel pulleys complete with bolts nut locking arrangement stoppers handles , including applying a priming coat of red lead paint carriage , hosting and taxes all complete as per building specification and direction E/I. |
| 28 | Supplying, fitting and fixing fully glaxed steel door, windows or ventilations of standard rolled 'Z' and mullion steel sections and size as per IS-1038 joints met and welded with 100x16x3mm M.S. lugs fixed in cement concrete (1:2:4) blocks 15x10x10cm, size including cost of oxidised iron fittings, with hinges, handle per steps, catch springs, 3mm thick palin glass panes with Aluminimum beads and inner frame fixed with lugs with 20mm long 6.3mm G.I. counter sunk machine screw and nuts and applying a coat of red lead paint carriage to work site hoisting and placing in position in all storys and taxes all complete as per building specification and direction of E/I. |
| 29 | Providing Tor steel reinforcement of 8mm. Dia rods as per approved design & drawing with cutting, bending and binding with annealed wire with cost of wire removal of rust, placing the rods in position {TMT Fe 500 (only valid for Tata(Tiscon), Sail, JSPL, Electrosteels Ltd. Bokaro and vizag (RINL)} (excluding carriage of bars to work site) all complete as per building specification and direction of E/I8 mm |
| 30 | 10 mm |
| 31 | 12 mm |
| 32 | Labour for fabricating, erecting, hoisting and fixing in position structural steel work in R.S. joists, channels, angles, Tees, flats, plates, lattice members, built up compound sections in columns, girders, staircase, or trusses including cost of gusset plates, holding down bolts, anchor plates at all heights and depths, bolting, welding (machining wherever necessary) with applying a priming coat of red lead paint all complete as per building specification and direction of E/I. |
| 33 | S/F/F MS grill gate with MS grill made of 20X6 MS flats or 16 mm square bars fitted on ---- do ---E/I ( When steel is not supplied by the deptt.)Entry gate 4M wide and 1.5M height and wicket gate 1 M wide and 1.5 M height. |
| 34 | Structural Steel work in single section, fixed with or without connecting plate, including cutting hoisting fixing in position and applying a priming coat of approved steel primer all complete. |
| 35 | Providing designation 75B one brick flat soling joints filled with local sand including cost of watering taxes royalty all complete as per building specification and direction of E/I. |
| 36 | Providing 50 mm thick cement concrete flooring 1:2:4 with 20 mm to 6 mm size graded stone chips finished with flooring coat of neat cement in panels including cost of curing , taxes, royalty all complete as per building specification and direction of E/I. |
| 37 | Extra for Providing and fixing 30x4mm glass strips in joints of flooring, complete job as per specifications and direction of E/I. |
| 38 | Providing and laying hydraulically machiine pressed terrazo tilles 20mm thick of approved texture with down marble chips of approved shade, size and quality, laid on 19mm, thick bed of lime mortar (1:1:1) (lime: surkhi: sand) with neat cement slurry mixed with pigment to match the shade of tiles between joints, including rubbing and polishing to granolithic finish with approved quality of carborandum stone including cost of curing, roualty and taxes all complete as per building specification and direction of E/I. (c) any light colour with 100% white cement |
| 39 | Providing and laying hydraulically machiine pressed terrazo tilles 20mm thick in skirting of approved texture with 4 mm down marble chips of approved shade, size and quality, over 12mm thick cement palster (1:3) base with neat cement slurry mixed with pigment to match the shade of tiles between joints, including rubbing and polishing to granolithic finish with approved quality of carborandum stone including cost of curing, roualty and taxes all complete as per building specification and direction of E/I. (c) any light colour with 100% white cement |
| 40 | Providing and laying 25mm thick kota stone in risers of steps, skirting and pillars of approves size, texture and colour laid over 12mm thick cement mortar (1:3) and joined with grey cement slurry mixed with pigment to match the slab including rubbing to granolithic finish with approved quality of carborandum stone including cost of curing, royalty and taxes all complete as per building specification and direction of E/I. |
| 41 | Providing and laying 6mm precast white glazed tiles in walls over 12mm, cement mortar (1:3) and jointed with gray cement slurry, flush pointed with white cement including rubbing, polishing and cost of curing, taxed and royalty all complete as per building specification and direction of E/I. |
| 42 | Providng 12mm thick cement plaster (1:4) with clean coarse sand of F.M. 1.5 including screening, curing with all leads and lifts of water, scaffolding taxes and royalty all complete as per building specification and direction of E/I. |
| 43 | Providng 12mm thick cement plaster (1:3) with clean coarse sand of F.M. 1.5 including screening, curing with all leads and lifts of water, scaffolding taxes and royalty all complete as per building specification and direction of E/I. |
| 44 | Providng 12mm thick cement plaster (1:6) with clean coarse sand of F.M. 1.5 including screening, curing with all leads and lifts of water, scaffolding taxes and royalty all complete as per building specification and direction of E/I. |
| 45 | Providing 6mm thick cement plaster (1:4) in ceiling with celean coarse sand of F.M. 1.5 including screening, curing with all leads and lifts of water, scaffolding taxes and royalty all complete as per building specification and direction of E/I. |
| 46 | Providing 1.5mm cement punning including curing, carriage of water with all leads and lifts as per building specification and direction of E/I |
| 47 | Providing 12mm thick water proof cement plaster(1:3) with clean coarse sand of F.M 1.5 with 5% cico or any other approved water proofing compound including-do- |
| 48 | Providng 19mm thick water proof cement plaster (1:3) with clean coarse sand of F.M. 1.5 including screening, curing with all leads and lifts of water, scaffolding taxes and royalty all complete as per building specification and direction of E/I. |
| 49 | Providing two coats of dry distemper of approved shade and make over a primer coat of washing over new surface including preparing the plastered surface by rubbing smooth with pumice stone or fine sand paper applying putty wherever required, scaffolding washing floors and taxes all complete as per building specification and direction of E/I. |
| 50 | Providing two coat of snowcem of approved shade and make over a coat of cement of primer on new surface mcluding preparing the plastered surface smooth with sand paper, soaping, curing and taxes all complete as per building specification and direction of E/I. |
| 51 | White washing three coats over new surface in ceiling. |
| 52 | Providing french spirit polishing over new wooden surface to give desired texture and gloss with approved make and shade of ready mixed french polish including cleaning the surface after removing dirt scales, smokes, grease and sand papering, including cost of scaffolding and taxes all complete as per building specification and direction of E/I. |
| 53 | Providing two coats of synthetic enamel paint of approved shade and made over steel surface including cleaning the surface thoroughly, scaffolding and taxes all complete as per building specification and direction of E/I. |
| 54 | Labou for fitting and fixinf GCI sheet roofing in proper slope including the cost of 'J' OR 'L' hooks,lipmpet and bitumen washers,carriage of sheets to work site and taxes all complete as per building specification and direction of E/I |
| 55 | Water proofingfor Old and New Roof Slab:-Providing and laying water proofing treatment on roof slab by applying two Component ,factory designed ,ready to use,acrylic modified flexible material applied with brush,roller or spray for water proofing coating as per manufacturer specification with following steps-do- |
| 56 | Supplying, fitting and fixing vitreous white glazed earthen ware I.W.C of parry Hindustan or any other ISS approved make with 100mm H.C.I 'P' trap 15 litres C.I pull and let go flushing cistern of names or other I.S.S equivalent make, complete with all fittings, C.I. or CC brackets 32mm alkathene/PVC telesopic flush, pipe about 2M long with one brasscoupling and clamps G.I. chain and pull including supplying and fixing a pair of vitreous white glazed earthenware ware footrest to be fixed in floor 15mm C.I. body brass spindle stope cock of weight not less than 50gm, 15mm PVC connection pipe 450mm long and the exposed pipe and cistern with two coats of approved paint over a coat of red oxide primer etc. all complete as per specification and direction of E/I. 510 mm long with 12.5 lit low level PVC cistern ( C )With 10 lit. low level PVC cistern |
| 57 | Supplying, fitting and fixing flat back or angular, lipped front vitreous white glazed earthen ware urinal of 'Hindustan \\"Parry\\" or any other approved ISS make with 5 liters capacity C.I automatic fulsiing cistern of reliance for any other ISS approved make with all fittings with CI or RS brackets, standare size GI flush pipe with fitting clamps, 15mm C.I. brass spindle stop cock of approved quality weight not less than 400gm, 15mm PVC / Alkthene pipe 450mm longwith brass coupling at both ends and doing plumber joints including painting of exposed part with two coats of approved paintover a priming coat of red oxide, cutting wall and floor, making good the same etc. all complete as per specification and direction of E/I. |
| 58 | Supplying fitting and fixing vitreous white glazed earthen ware indian squating type 600 x 300 mm urinal plate of parry , hindustan or any other I.S.S approved make with internal flusing rim ,100 mm white glazed earthen ware channel about 1 m long 5 litre capacity C.I automatic flusing cistern of rliance or any other approved make with fittings R.S or C.I brackets 15 mm and 45 cm long PVC/Alkathene pipe standard G.I flush pipe for backand front with spreader fittings and brass coupling etc. 15 mm C.I body brass complete including painting of exposed parts with 2 coats of approved paint over coat of red oxide primer and cutting the wall and floor and making goood the same as per specification and direction of E/I. |
| 59 | Supplying, fitting and fixing vitreous white glazed earthen ware wah hand basin of parry or Hindustan or any other ISS approved make supported on painted C.I. or R.S. brackets 32mm C.I. brass waste, 15mm dia C.I. body brass spindle stop cock of approved quality of weight not less than 350 gm, 32mm PVC waste pipe 750mm long wtih brass coupling at one end and making plumber joints etc. all complete as per specification and as per direction of E/I. |
| 60 | Providing and fixing 600 x 450 mm beveled edge mirror of superior glass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete. |
| 61 | Providing and fixing brass Stop cock of approved quality |
| 62 | Providing and fixing male ended 15 mm dia brass bib cock of approved quality (Wt. not less than 350 gms.) with extra socket all complete as per specification and direction of E/I. |
| 63 | Providing and supplying in standard lenghts high density polythylene pipe (HDPE pipe) 25mm to 500mm dia confirming to IS 4984-4984/14151/12786/13488 (Latest Revision with necessary jointing materials like mechanical connector i.e thread/insert joint /quick release coupler ---do---- 140 mm |
| 64 | 160 mm |
| 65 | 110 mm |
| 66 | PE100-PN06 dia 110 mm |
| 67 | Foot Mounted Motors TEFC 1500 RPM |
| 68 | Cost of Drilling 200mm X 165MM x 125mm mtr deep nore well in all kind soil and rocks in rural area for installation of pump set with hydraulic DTH Rig machine all complete including all materials ,tolls ,drilling rig,air compressed and equipments as well, as fuel,lubrication and cost of transportation og rig machine and other vehicle upto site.From 0.00 M to 50.00 M below G.L |
| 69 | From 51.0 M to 125.00M |
| 70 | Supplying submesible pump sets confirming to 8034 and motar conforming to IS 9283.Pump shall be suitable for various delivery head and discahrge with stainless steel pump shaft and polypropylene /noryl impeller.Motor suitable for working on 415+10,3HP,50Hz,AC supply with cable guard ,thrust carbon filter bearing to withstand ebtire hydraulic thrust ,water proof bindinf shall be provided .The pump set shall be suitable for direct coupling.Pump shall have suitable outlet as per manufacture design.Anti thrust stream lined non return valve shall be provided with pump,3meter submersible copper conductor cable in single/double run shall be provided with each pump. Submersible pump set 100 mm dia upto 20stages 2HP |
| 71 | Supply of 3 core 2.5 sqmm FR pvc insulated Copper Wire CORE 2.5sq mm |
| 72 | Polyethene water storage Tank of mark(e.g.,Sintex/sinter/himgiri/gangotri etc) with cover and locking system |
| 73 | Supply of G.I. Pipes (Tata mark) or equivalent for cable.50mm dia |
| 74 | E/W in exavation of cut off trenches by the hydraulic excavator as per designied section in soft rock (where blasting is not needed) (vide classifictaion type of soil item-C ) with disposal of spoil beyond 1/2 km from centre of trench but upto 1 km with all lifts by tipper including construction and maintenance of haul road all complete as per specification and direction of E/I |
| 75 | Supplying and laying gravel filter (sixe 5mm to 15 mm) in filter blanket and in toe drain (in horizontal portion of Dam) as per design and drawing with watering, compaction including cost of material, royalty all taxes etc but excluding the cost of carriage all complete as per specification and direction of E/I |
| 76 | Supplying and laying good quality stone metal filter (20mm to 63mm size) in rock toe, heel trench, toe drain as per design and drawing including cost of material, royalty, all taxes etc but excluding cost of carriage all complete as per specification and direction of E/I. |
| 77 | Wiring for light point/fan point/ exhaust fan point/ call bell point with 1.5 sq. mm FR PVC insulated copper conductor single core cable in surface / recessed PVC conduit, piano type switch, phenolic laminated sheet with suitable size PVC/MS box etc. as required. Group A |
| 78 | Group B |
| 79 | Group C |
| 80 | Wiring for light / power plug with 2 x 4 sq.mm Sq.mm FR PVC insulated copper conductor single core cable in surface/ recessed PVC conduit alongwith 1 No 4 sq. mm FR PVC insulated copper conductor single core cable for loop earthing etc. as required. |
| 81 | Wiring for light/ power plug with 4 X 4 sq. mm FR PVC insulated copper conductor single core cable in surface/ recessed PVC conduit alongwith 2 No 4 sq. mm FR PVC insulated copper conductor single core cable for loop earthing etc. as required. |
| 82 | S/F PVC conduit:- Supplying and fixing of following sizes of PVC conduit along with accessories in surface/recess including cutting the wall and making good the same in case of recessed conduit as required.25 mm |
| 83 | S/F PVC/G.I. boxes:- Supplying and fixing of following sizes of PVC/G.I box on surface / recess with suitable size of phenolic laminated sheet cover in front including painting etc. as required. 75x75x50mm |
| 84 | 147x93x47mm deep/ (5\\" x7\\") |
| 85 | S/F Modular base & cover plate:- Supply and fixing following size/ modules, GI box along with modular base & cover plate for modular switches in recess etc. as required. 4/5 module |
| 86 | S/F Modular type switch/socket:- Supply and fixing following modular switch / socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required.3 pin 5/6 amp socket outlet |
| 87 | Telephone socket outlet |
| 88 | S/F light plug point with modular type accessories:- Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 3 pin 5/6 amps modular socket outlet and 5/6 amps modular switch, connection, painting etc as required(For light plugs to be uysed in non residential buildings). |
| 89 | S/F power plug point with modular type accessories :- Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 6 pin 15/16 amps modular socket outlet and 15/16 amps modular switch, connection, painting etc as required (For light plugs to be used in non residential buildings) |
| 90 | S/F Modular type electronic fan regulator :- Supply and fixing stepped type electronic fan regulator on the existing modular plate switch box including connections but excluding modular plate etc as required |
| 91 | Supply and fixing call bell/ buzzer suitable for D.C/ A.C single phase 230 volts complete as required. |
| 92 | S/F ceiling rose :- Supply and fixing 2 pin, 5 amp. Ceiling rose on the existing junction box/ wooden block including connection etc as required. |
| 93 | S/F Batten holder :- Supply and fixing batten/ angle holder including connection etc as required |
| 94 | Supply, Installation, testing and comissioning of following size ceiling fanv3 blades confirming to IS:374:2019, including wiring the down rods of standard length(upto 30 cm) with 1.5sq mm FR PVC insulated, copper conductor single core cable, etc. as required. |
| 95 | S.I.T.C of following rating surface mounted LED tube light fitting suitable for 230V 50Hz, single phase supply etc. complete as required.10/12W LED Tube Light |
| 96 | 20/22W LED Tube Light |
| 97 | ITC exhaust fan upto 510 mm. sweep :- Installation of exhaust fan upto 510 mm sweep in the existing opening, including making the hole to suit the size of the above fan making good the damage, connection, testing, commissioning etc. as required. |
| 98 | 9\\" (230 mm) metal Exhaust fan. |
| 99 | Swagged steel tubular pole of heiht 9 mmtr. Connfirming to IS 2713 In three section with steel baser size, bottom of the pole made of 50 mm dia MSB Clamp pipe welded to 300 mm long MS canopy of suitable dia at angle of 102.5 suitable size of nuts and bolts including rating of one cost steel primer and two coat of read oxide all complete as requirerd. |
| 100 | Single Arm 1 metre long |
| 101 | S/F S.P. MCB DB :- Supply and fixing following way, single pole and neutral, sheet steel, MCB distribution board, 240 volts, on surface/ recess, complete with tinned copper busbar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator) 2 way, single door |
| 102 | S/F \\"B< series, S.P. MCB :- Supply and fixing 6 amps to 32 amps rating 240 volts, 10KA, 'B' curve, miniature circuit breaker suitable for inductive load of following poles in the exsisting MCB DB complete with connection testing and commisssioning etc. as required. 6/32 amps, single pole \\"B\\" series |
| 103 | Earthing with G.I. earth plate 600 mm X 600 mm X 6 mm thick including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe. (but with charcoal/ coke and salt) as required. |
| 104 | Earthing with copper earth plate 600mm X 600mm X 3mm thick including accessories, and providing masonary enclosure with cover plate having locking arrangement and watering pipe etc. (with charcoal or coke and salt) |
| 105 | Supply and laying of following sizes Al. conductor PVC insulated PVC seathed cable of 1100 V grade at a depth of 750 mm B. G. L 3.5 core (95 Sqm) |
| 106 | 3.5 core(50 sqm) |
| 107 | 3.5 core(35 sqm) |
| 108 | 2 core 10 sqm |
| 109 | Supply and laying of 3.5 x 120 mm2 Al. armoured cable. |
| 110 | 1:1.5:3 (1 Cement: 1.5 coarse sand (zone-III) ncluding manufactured sand derived from Recycled Concrete Aggregate Recycled Concrete Aggregate (RCA) upto 25% : 3 graded stone aggregate 20 mm nominal size (Recycled Concrete Aggregate (RCA) upto 25%) |
| 111 | Making plinth protection 50 mm thick of cement concrete 1:3:6 (1 cemnt: 3 coarse sand: 6 graded stone aggregate 20 mm nominal size) over 75 mm bed of dry brick ballast 40 mm nominal size well rammed and consolidated and grouted with fine sand including finishing the top smooth. |
| 112 | Providing and fixing 18 mm thick gang saw cut, mirror polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. complete at all levels. |
| 113 | Providing and Fixing 1mm thick M.S.Sheet Door with frame of 40x40x6 M.S.Angle Iron and 3mm Gusset Plates at the junctions and corners, all necessary fitting complete, including applying a primer coat of approved primer with 30x6 Diagonal braces and central cross pieces.Using M.S. angels 40x40x6 mm for diagonal braces |
| 114 | Steel work welded in built up sections/ framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required.In gratings, frames, guard bar, ladder, railings, brackets, gates and similar works |
| 115 | Providing and laying rectified Glazed Ceramic floor tiles 300 x 300 mm or more (thickness to be specified by the manufacturer) of 1st quality conforming to IS : 15622 of approved make in colours White, lvory, Grey, Fume Red Brown, laid on 20 mm thick cement mortar 1:4 (1 Cement : 4 Coarse sand) including grouting the joints with white cement and matching pigment etc., complete. |
| 116 | Providing ridges or hips of width 60cm over all width plain G.S. sheet fixed with polymer coated J. or L hooks, bolts and nuts 8 mm dia. G.I. limpet and bitumen washers complete (0.80mm thick with zinc coating not less than 275gm/m2) |
| 117 | Providing and fixing 15 cm wide 45 cm over all semicircular plain G.S sheet gutter with iron brackets 40 x 3 mm size, bolts, nuts and washers etc. including making necessary connections with rain water pipes complete. 0.8 mm thick with zinc coating not less than 275 gm/Sqm. |
| 118 | Providing and fixing on wall face unplasticised - Rigid PVC rain water pipes conforming to IS : 13592 Type A. 110 mm dia |
| 119 | Providing and fixing on wall face unplasticised - PVC moulded fittings / accessories for unplasticised - Rigid PVC rain water pipes conforming to IS : 13592 Type A. 110 mm shoe. |
| 120 | Providing and fixing unplasticised -PVC pipe clips of approved design to unplasticised - PVC rain water pipesby means of 50x50x50mm hard wood plugs, screwed with M.S Screws of required length, including cutting brick work and fixing in cement mortar 1:4 and making good the wall etc. complete |
| 121 | Providing and fixing to the inlet mouth of rain water pipe cast iron grating 15 cm diameter. |
| 122 | Providing & fixing UV stabilised fiberglass reinforced plastic sheet roofing up to any pitch, including fixing with polymer coated 'J' or 'L' hooks, bolts & nuts 8mm dia. G.I plain/bitumen washers complete but excluding the cost of purlins, rafters, trusses etc. The sheets shall be manufactured out of 2400 TEX panel rovigs incorporating minimum 0.3% ultra-violet stabiliser in resin system under approximately 2400 psi and hot cured. They shall be of uniform pigmentation and thickness without air pockets and shall conform to IS 10192 and IS 12866.The sheets shall be opaque or translucent, clear or pigmented, textured or smooth as specified. |
| 123 | Providing and fixing precoated galvanised iron profile sheets (size, shape and pitch of corrugation as approved by Engineer-in-charge) 0.50 mm (+ 0.05 %) total coated thickness with zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns. Sheet should have protective guard film of 25 microns minimum to avoid scratches during transportation and should be supplied in single length upto 12 metre or as desired by Engineerin-charge. The sheet shall be fixed using self drilling /self tapping screws of size (5.5x 55 mm) with EPDM seal, complete upto any pitch in horizontal/ vertical or curved surfaces, excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required |
| 124 | Providing and fixing precoated galvanised iron profile sheets (size, shape and pitch of corrugation as approved by Engineer-in-charge) 0.50 mm (+ 0.05 %) total coated thickness with zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns. Sheet should have protective guard film of 25 microns minimum to avoid scratches during transportation and should be supplied in single length upto 12 metre or as desired by Engineerin-charge. The sheet shall be fixed using self drilling /self tapping screws of size (5.5x 55 mm) with EPDM seal, complete upto any pitch in horizontal/ vertical or curved surfaces, excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required |
| 125 | Providing and fixing precoated galvanised steel sheet roofing accessories 0.50 mm (+0.05 %) total coated thickness, Zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns using self drilling/ self tapping screws complete : Ridges plain (500 - 600mm) |
| 126 | Gutter (600 mm over all girth) |
| 127 | Providing and laying 60mm thick factory made cement concrete interlocking paver block of M -30 grade made by block making machine with strong vibratory compaction, of approved s;ze, design & shape, laid in required colour and pattern over and including 50mm thick compacted bed of coarse sand, filling the joints with line sand etc. all complete as per the direction of Engineer-in-charge. |
| 128 | Providing and laying at or near ground level factory made kerb stone of M-25 grade cement concrete in position to the required line, level and curvature, jointed with cement mortar 1:3 (1 cement: 3 coarse sand), including making joints with or without grooves (thickness of joints except at sharp curve shall not to more than 5mm), including making drainage opening wherever required complete etc. as per direction of Engineer-in-charge (length of finished kerb edging shall be measured for payment). (Precast C.C. kerb stone shall be approved by Engineer-in-charge) |
| 129 | Providing and fixing Stainless Steel A ISI 304 (18/8) kitchen sink as per IS:13983 with C.I Brackets and stainless steel plug 40mm including painting of fillings and brackets, cutting and making good the walls wherever required |
| 130 | Providing and fixing soil, waste and vent pipes 100 mm dia |
| 131 | Providing & fixing M.S holder-bat clamps of approved design to Sand Cast iron/cast iron (spun) pipe embedded in and including cement concrete blocks 10x10x10cm of 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) including cost of cutting holes and making good the wall etc.For 100 mm dia pipe |
| 132 | Providing and Fixing PTMT Bottle trap 31mm single piece moulded with height of 270 mm, effective length of tail pipe 260mm from the center of the the waste coupling. |
| 133 | Providing & Fixing Waste Coupling For Wash Basin and Sink |
| 134 | Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge.Water point for cleaning of plant and vehicle parking area 25 mm nominal dia Pipes |
| 135 | 32 mm nominal dia Pipes |
| 136 | Providing and fixing G.I.pipes complete with G.I.fittings and clamps,including cutting and making good the walls etc. (Internal work): Concealed pipe including painting with anti corrosive bitumastic paint,cutting chases and making good the wall.15 mm dia nominal bore |
| 137 | Providing and fixing uplasticised PVC connection pipe with brass unions :45 cm length. 15 mm nominal bore |
| 138 | Providing and fixing C.I. sluice valves (with cap) complete with bolts, nuts, rubber insertions etc. (the tail pieces if required will be paid separately) : 150 mm diameter |
| 139 | Providing and fixing PTMT soap Dish Holder having length of 138 mm, breadth 102mm, height of 75mm with concealed fitting arrangements. Weighing not less than 106 gms. |
| 140 | Providing M.S. foot rests including fixing in manholes with 20 X 20 X 10 cement concrete blocks 1:3:6 (1 Cement : 3 Coarse: 6 graded stone aggregate 20 mm nominal size) as per standard design:With 20 X 20 mm square bar |
| 141 | With 20 mm diameter round bar |
| 142 | With 20 mm diameter round bar |
| 143 | Supplying and fixing C.I. cover without frame for manholes :500 mm diameter C.I. cover (medium duty) the weight of the cover to be not less than 58 kg |
| 144 | Providing and fixing in position pre-cast R.C.C. manhole cover and frame of required shape and approved quality Square shape 450 mm internal dimensions. |
| 145 | Circular shape 500mm internal dia. |
| 146 | Providing and laying water proofing treatment on roofs of slabs by applying cement slurry mixed with water proofing cement compound consisting of applying: a) after surface preparation, first layer of slurry of cement @ 0.488 kg/sqm mixed with water proofing cement compound @ 0.253 kg/sqm. b) laying second layer of Fibre glass cloth when the first layer is still green. Overlaps of joints of fibre cloth should not be less than 10 cm. c) third layer of 1.5 mm thickness consisting of slurry of cement @ 1.289 kg/sqm mixed with water proofing cement compound @ 0.670 kg/sqm and coarsesand @ 1.289 kg/sqm. This will be allowed to air cure for 4 hours followed by water curing for 48 hours. The entire treatment will be taken upto 30 cm on parapet wall and tucked into groove in parapet all around. d) fourth and final layer of brick tiling with cement mortar (which will be paid for separately. For the purpose of measurement the entire treated surface will be measured. |
| 147 | Supplying, assembling, lowering and fixing in vertical position in bore well, unplasticized PVC medium well casing (CM) pipe of required dia, conforming to IS: 12818, including required hire and labour charges, fittings & accessories etc. all complete, for all depths, as per direction of Engineer -in-charge |
| 148 | Providing and fixing suitable size threaded mild steel cap or spot welded plate to the top of bore well housing/ casing pipe, removable as per requirement, all complete for borewell of: |
| 149 | Providing and fixing M.S. clamp of required dia to the top of casing/ housing pipe of tubewell as per IS: 2800 (part I), including necessary bolts & nuts of required size complete. 200mm clamp |
| 150 | Uprooting rank vegetation and weeds by digging the area to a depth of 60 cm, removing all weeds and other growth with roots by forking repeatedly,breaking clods, rough dressing, flooding with water, uprooting fresh growths after 10 to 15 days and then fine dressing for planting new grass, including disposal of all rubbish with all leads and lifts |
| 151 | Preparation of beds for hedging and shrubbery by excavating 60 cm deep and trenching the excavated base to a further depth of 30 cm, refilling the excavated earth after breaking clods and mixing with sludge or manure in the ratio of 8:1 (8 parts of stacked volume of earth after reduction by 20% : one part of stacked volume of sludge or manure after reduction by 8%), flooding with water, filling with earth if necessary, watering and finally fine dressing, leveling etc. including stacking and disposal of materials declared unserviceable and surplus earth by spreading and leveling as directed, within a lead of 50 m, lift up to 1.5 m complete (cost of sludge, manure or extra earth to be paid for separately |
| 152 | Supplying and stacking of good earth at site including royalty and carriage upto 5 km lead complete (earth measured in stacks will be reduced by 20% for payment |
| 153 | Grassing with selection No. 1 Doob grass including watering and maintenance of the lawn for 30 days or more till the grass forms a thick lawn, free from weeds and fit for mowing including supplying good earth, if needed (the grass and good earth shall be paid for separately. With grass Turf( Lawn Area) |
| 154 | Plantation of Trees, Shrubs, and Hedge at site i/c watering and removal of unserveiceable material’s as per direction of officer in charge (excluding cast of plant & water) Trees Plant |
| 155 | Shrubs Plant |
| 156 | Hedge Plant /Ground cover |
| 157 | Providing and stacking of plant Canna dwarf of height 25 to 30 cm., 2 to 3 suckers in earthen pots of size 20 cm Earthen Pot/Plastic Pot and as per direction of the officer-in-charge |
| 158 | Providing and stacking of plant Canna dwarf of height 25 to 30 cm., 2 to 3 suckers in earthen pots of size 20 cm Earthen Pot/Plastic Pot and as per direction of the officer-in-charge |
| 159 | Providing and stacking of Azadirachta indica ( Neem ) of height 120-130cm in big polybag of size 25 cm as per direction of the officer-in-charge |
| 160 | Providing and fixing 4 mm dia copper wire on surface or in recess for loop earthing etc. as required. |
| 161 | Providing and fixing testing joint, made of 20 mm X 3 mm thick G.I. strip, 125 mm long, with 4 nos. of G.I. bolts, nuts, chuck nuts and spring washers etc. complete as required. |
| 162 | Supply laying and jointing perforeted HDPE pipe. 300 mm dia |
| 163 | Providing & fixing 1.5 mm HDPE geomembrane at land fill site including in situ welding of HDPE membranes, laying, anchoring in trench, seaming, testing as per manufacturers directions as per standard design & drawings. |
| 164 | Supply laying and jointing perforeted HDPE pipe 300 mm Dia |
| 165 | Solar Based Street Light of Following SpecificationSemi Integrated Solar Street Light 30 WBattery Type Lithium Ion 11.1V 24ahSolar Panel 12V 60WLED Chip Brand OsramLed Life Time Over 5000 hoursCharging Time 5 – 6 hoursLumen 3500 – 3700Lighting Viewing Angle 120°Backup Time 1 – 2 Days |
| 166 | Office /Visitors chair Stellar R (Stellar COM-205) IS3499 (Q3 CATEGORY) Mateial of fabric back cover:Polyster Frame material:CRCA ERW Round pipe Thickness of Plywood used in backrest :12mm Density of Polyeuthrnae foam used in seat/backrest:40kg/cum |
| 167 | Kent ROFully automatic with auto cut off RO Potable water Purification system Kent RO R (KENT RO ELITE PLUS COMMERCIAL RO 50LPH) IS9001:2015 |
| 168 | FRP Strip cast iron bench with integrated seat and backoutddor in lawn area(DP-115) Thickness of cast iron frame body : 36mm GI Pipe diameter for body(Nominal bore) : 25mm -B Class conforming to IS1239 PU coated with layer of thickness of 60 micron. FRP Strip thickness (for seat) : 5mm FRP Strip thickness (for back) : 5mm |
| 169 | Pressure Sand filter & Activated carbon filter(PSF & ACF) with description : 1. Sand Filter FRP Vessel (4\\" Top opening) 16 x 65 Internal distribution system Top mount multiport valve 25mm Media-200kg(Graded sand(2x4,4x8,8x16)) 2.Carbon Filter FRP Vessel (4\\" Top opening) 16 x 65 Internal distribution system Top mount multiport valve 25mm Media-75 kg(GAC,COCONUT BAse,IV-80) 3.PUMP WITH STAND Interconnecting UPVC piping-25mm Pressure gauge-2Nos. |
| 170 | Ozonation unit with description: Ozone generator- 30gm/hr (1 no) Oxygen concentrator 5LPM (1No) Venturei Injector1\\" with NRV 1/4\\" (1No.) SS Static mixer 1\\" -5mtrs. Teflon tube 6mm -10mtrs. Polyeurathane Tube 10mm (1No.) Ozone mixing pump CHLF4-60 (1No.) Servo stabiliser 2KVA (1No.) Plumbing and Electrical materials (1No.) |
| 171 | Holland 6500 2WD Turbo super New holland Two wheel drive power operated Tractors(New ) Tractor Engine 45/50HP Bharat stage -IV |
| 172 | KAM AVIDA suction machine of 3500 litres Tank Capacity (KAMVAC-3LT-MANO(without tractor) IS 13496Overall length : 5010 mm Overall width : 1830mm Vacuum pump flow : 390 cum/hr Suction hose internal : 75 mm |
| 173 | Chips |
| 174 | Metals |
| 175 | Bricks |
| 176 | Mazdoor semi skilled(With septage suction machine) |
| 177 | Driver /Tractor Operator |
| 178 | Sanitary Supervisor Diploma Holder |
| 179 | Tractor 3500 L Capacity |
| 180 | Desludging Machine |
| 181 | Complete O & M and repair of vehicle and suction pump which includes painting,general engine repair,tyre change,wheel alignment,engine oil change,coolentand other minor repairs,oil and greasing,valve change and pipe change etc. |
| 182 | Complete O & M and repair submersible pump |
| 183 | Complete O & M and repair suction pump |
| 184 | Cleaning ABR |
| 185 | Watchman/Chaukidar |
| 186 | Mazdoor semi skilled(Plant Maintenance & Horticulture) |
| 187 | Power consumptuion of entire plant |
| 188 | Safety Helmet for Plant Operator |
| 189 | Facemask |
| 190 | Gum Boots |
| 191 | Safety Gloves |
| 192 | Stationary Items |
| 193 | Sample Testing |
| 194 | Capital invetment cost for technology based operations optimization such that includes installation of GPS , GPS tracker in sludging vehicle , software subscription.(1 VEHICLE) |
| 195 | Dedection of Profit of Sale of Organic Manure(MT) = 10kl x1000x 2.5% (T.S) x1. (Density)x15% Moisture Rate of Organic Manure=2500/MT |
| 196 | Mazdoor semi skilled(With septage suction machine) |
| 197 | Driver /Tractor Operator |
| 198 | Sanitary Supervisor Diploma Holder |
| 199 | Tractor 3500 L Capacity |
| 200 | Desludging Machine |
| 201 | Complete O & M and repair of vehicle and suction pump which includes painting,general engine repair,tyre change,wheel alignment,engine oil change,coolentand other minor repairs,oil and greasing,valve change and pipe change etc. |
| 202 | Complete O & M and repair submersible pump |
| 203 | Complete O & M and repair suction pump |
| 204 | Sand Replacement in SDB |
| 205 | Cleaning ABR |
| 206 | Watchman/Chaukidar |
| 207 | Mazdoor semi skilled(Plant Maintenance & Horticulture) |
| 208 | Power consumptuion of entire plant |
| 209 | Safety Helmet for Plant Operator |
| 210 | Facemask |
| 211 | Gum Boots |
| 212 | Safety Gloves |
| 213 | Stationary Items |
| 214 | Sample Testing |
| 215 | Capital invetment cost for technology based operations optimization such that includes installation of GPS , GPS tracker in sludging vehicle , software subscription. |
| 216 | Deduction of Profit of Sale of Organic Manure= 18 KLD*1000*2.5% (t.s)*1.05 (Density)* 15% Moisture |
| 217 | Mazdoor semi skilled(With septage suction machine) |
| 218 | Driver /Tractor Operator |
| 219 | Sanitary Supervisor Diploma Holder |
| 220 | Tractor 3500 L Capacity |
| 221 | Desludging Machine |
| 222 | Complete O & M and repair of vehicle and suction pump which includes painting,general engine repair,tyre change,wheel alignment,engine oil change,coolentand other minor repairs,oil and greasing,valve change and pipe change etc. |
| 223 | Complete O & M and repair submersible pump |
| 224 | Complete O & M and repair suction pump |
| 225 | Screen replacement in Screen chamber |
| 226 | Cleaning ABR |
| 227 | Watchman/Chaukidar |
| 228 | Mazdoor semi skilled(Plant Maintenance & Horticulture) |
| 229 | Power consumptuion of entire plant |
| 230 | Safety Helmet for Plant Operator |
| 231 | Facemask |
| 232 | Gum Boots |
| 233 | Safety Gloves |
| 234 | Stationary Items |
| 235 | Sample Testing |
| 236 | Capital invetment cost for technology based operations optimization such that includes installation of GPS , GPS tracker in sludging vehicle , software subscription.(1 VEHICLE) |
| 237 | Dedection of Profit of Sale of Organic Manure(MT) = 10kl x1000x 2.5% (T.S) x1. (Density)x15% Moisture Rate of Organic Manure=2500/MT |
| 238 | Mazdoor semi skilled(With septage suction machine) |
| 239 | Driver /Tractor Operator |
| 240 | Sanitary Supervisor Diploma Holder |
| 241 | Tractor 3500 L Capacity |
| 242 | Desludging Machine |
| 243 | Complete O & M and repair of vehicle and suction pump which includes painting,general engine repair,tyre change,wheel alignment,engine oil change,coolentand other minor repairs,oil and greasing,valve change and pipe change etc. |
| 244 | Complete O & M and repair submersible pump |
| 245 | Complete O & M and repair suction pump |
| 246 | Sand Replacement in SDB |
| 247 | Cleaning ABR |
| 248 | Watchman/Chaukidar |
| 249 | Mazdoor semi skilled(Plant Maintenance & Horticulture) |
| 250 | Power consumptuion of entire plant |
| 251 | Safety Helmet for Plant Operator |
| 252 | Facemask |
| 253 | Gum Boots |
| 254 | Safety Gloves |
| 255 | Stationary Items |
| 256 | Sample Testing |
| 257 | Capital invetment cost for technology based operations optimization such that includes installation of GPS , GPS tracker in sludging vehicle , software subscription.(1 VEHICLE) |
| 258 | Dedection of Profit of Sale of Organic Manure(MT) = 10kl x1000x 2.5% (T.S) x1. (Density)x15% Moisture Rate of Organic Manure=2500/MT |
| 259 | Mazdoor semi skilled(With septage suction machine) |
| 260 | Driver /Tractor Operator |
| 261 | Sanitary Supervisor Diploma Holder |
| 262 | Tractor 3500 L Capacity |
| 263 | Desludging Machine |
| 264 | Complete O & M and repair of vehicle and suction pump which includes painting,general engine repair,tyre change,wheel alignment,engine oil change,coolentand other minor repairs,oil and greasing,valve change and pipe change etc. |
| 265 | Complete O & M and repair submersible pump |
| 266 | Complete O & M and repair suction pump |
| 267 | Gravel Replacement in PGFB (if porosity decreased) |
| 268 | Cleaning ABR |
| 269 | 1 Watchman/Chaukidar (For 365 days) |
| 270 | 2 Mazdoor(Plant Maintenance & Horticulture) (for 300 days) |
| 271 | Power consumptuion of entire plant |
| 272 | Safety Helmet for Plant Operator |
| 273 | Facemask |
| 274 | Gum Boots |
| 275 | Safety Gloves |
| 276 | Stationary Items |
| 277 | Sample Testing |
| 278 | Capital invetment cost for technology based operations optimization such that includes installation of GPS , GPS tracker in sludging vehicle , software subscription.(1 VEHICLE) |
| 279 | Dedection of Profit of Sale of Organic Manure(MT) = 10kl x1000x 2.5% (T.S) x1. (Density)x15% Moisture Rate of Organic Manure=2500/MT |
| 280 | Add GST @ 18% |
| 281 | Add labourcess@1% Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Sep 30, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedOct 12, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 11 daysOct 14, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 13 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender