Tender For special Repair To Bldg No Owt-696,Owt-698 & Owt-699 (Office Shelter0 ; special Repair To Bldg No T-25; Provn Of 01 X Toiletncum Bathroom ; 01 X Septic Tank And 01 X Soakage Well At Likabali Mil Stn Under Ge 872 Ews
Tender Value
42.65 Lakhs
Estimated cost
Bid Submission
14 Oct 2026
10 days left
EMD
85400
Bank guarantee accepted
Document Fee
500
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Dhemaji → Assam
EMD Exemption
Not Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for special Repair To Bldg No Owt-696,Owt-698 & Owt-699 (Office Shelter0 ; special Repair To Bldg No T-25; Provn Of 01 X Toiletncum Bathroom ; 01 X Septic Tank And 01 X Soakage Well At Likabali Mil Stn Under Ge 872 Ews
BOQ
| Sl. No. | Item Description |
| 1 | Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing) and disposal of debris and rubbish complete all as specified and directed. |
| 2 | Demolition of un-reinforced cement concrete in ground floors and pavings n.exc 15cm thickness, (Below or above Ground level) and disposal of debris and rubbish to a distance complete all as directed by the Engr-in-Charge |
| 3 | Demolition of reinforced cement concrete of any description and in any position not otherwise specifically provided for complete all as directed and directed |
| 4 | Demolition of brick work or stone masonary built in cement mortor including all quoins & jambs etc. complete all as specified and directed |
| 5 | Taking down chowkats or frame, n.exc 1.5 Sqm each with shutters (without taking off shutter from the frame) complete all as specified and directed. |
| 6 | Taking down chowkats or frames, exc 1.5 but n.exc. 4 Sqm in each with shutter (without taking off shutter from the frame) complete all as specified and directed. |
| 7 | Taking down cement plaster on brick or stone walls etc including racking out joints, hacking for key, scrubbing down with water and removing rubbish complete all as specified and directed |
| 8 | Dismantling of plain or corrugated steel sheeting, any gauge, thickness, in roof covering including ridges and keeping serviceable sheets in safe custody for reuse in the work complete as directed. |
| 9 | Dismantling of wrought iron or mild steel work of any description not otherwise provided for complete all as specified and directed. |
| 10 | Dismantling Wall and ceiling boards (fibre, pulp, insulation, etc.) or insulation boards/slabs/ blankets, any thickness, including cover fillets/ snap grid frame etc complete all as specified and directed. |
| 11 | Taking up or down 15/20mm bore, Steel tubing and connections and keeping serviceable pipes in safe custody for reuse in the work after and including cleaning as directed. |
| 12 | Surface excavation n. exc 30 cm deep and averaging 15 cm deep and getting out in soft/loose soil complete all as specified and directed. |
| 13 | Excavation in trenches, not exceeding 1.5 M wide and not exceeding 1.5 M depth for foundation, trenches for shafts, wells, cesspits, manholes, pier holes, cable etc. n exc 10sq m on plan and n exc 1.5m in depth and getting out in soft/loose soil complete all as specified and directed. |
| 14 | Excavating in post holes (or similar holes) each n. exc. 0.5 cum, getting out returning, filling in and ramming earth or broken rubble mixed with earth around, in layers n. exc. 25 cm watering and removing surplus soil to distance n. exc 50 m and making good surface complete all as specified and directed. |
| 15 | Excavating over areas, n exc 1.5 m deep and getting out as in Soft/Loose Soil, complete all as specified and as directed. |
| 16 | Excavating over areas, exc 1.5 m deep but n exc. 3.00 and getting out as in Soft/Loose Soil, complete all as specified and as directed. |
| 17 | Excavating over areas, exc 3.0 m deep but n exc. 4.50 and getting out as in Soft/Loose Soil, complete all as specified and as directed. |
| 18 | Returning, filling in, including spreading, levelling, watering and well ramming in layers not exc 25 cm as in soft/loose soil complete all as specified and directed. |
| 19 | Removing excavated material not exc. 50 m and depositing where directed at a level not exc 1.5 m above the starting point complete all as specified and directed. |
| 20 | M & L for Sand filling under floors or in foundations including spreading, levelling, watering and consolidation complete all as specified and directed. |
| 21 | M & L for hardcore of gauge n.exc 63 mm of broken stone or boulders, deposited, spread and levelled in layers not exceeding 15 cm thick, watered and rammed to a true surface complete all as specified and directed. |
| 22 | Loose filling with aggregates of gauge 80 to 150 mm in soakage pits, soakage wells |
| 23 | M & L for Plain cement concrete 1:4:8, type D-2 (using 40 mm graded stone aggregate) as in foundation, filling and mass concrete, etc complete all as specified and directed. |
| 24 | M & L for precast cement concrete (1:2:4) type B1 (using 12.5mm graded stone aggregate) setting in CM 1:6 work for in landings, cover slabs (for man holes etc.) chullah hoods, chajjas, water troughs, mangers, shelves and similar articles with plain faces |
| 25 | M & L Reinforced Cement Concrete 1:1.5:3, Type A-1(nominal design mix (20mm graded crushed stone aggregate) as in Slab supported on Walls, complete all as specified and as directed.NOTE : Formwork and Reinforcement shall be Measured and Paid for separately under relevant Items. |
| 26 | M & L Reinforced Cement Concrete 1:2:4, Type A-1 (Nominal Mix) (using 12.5 mm graded stone aggregate) for columns ,pillars ,Piers ,posts and struts complete all as specified and directed.(Note : Reinforcement will be measured & paid seperately) |
| 27 | M & L Reinforced Cement Concrete 1:1.5:3, Type A-1 (Nominal Mix) (using 20 mm graded stone aggregate) for columns ,pillars ,Piers ,posts and struts complete all as specified and directed.(Note : Reinforcement will be measured & paid seperately) |
| 28 | Material and Labour RCC (Nominal mix) 1:2:4 ( Using 12.5 mm graded crushed stone aggregates) as in Foundations, including rafts, footings, foundation beams; plinth beams; bases for columns, etc.; basement slabs, under-reamed piles and mass concrete complete all as specified and directed. |
| 29 | M & L Reinforced Cement Concrete 1:2:4, Type A-1 (Nominal Mix) (using 20 mm graded stone aggregate) as in beams, cantilevers, lintels over 1.5m span complete all as specified and directed.(Note : Reinforcement will be measured & paid seperately) |
| 30 | M & L Reinforced Cement Concrete 1:1.5:3, , Type A-1 (Nominal Mix) (using 20 mm graded stone aggregate) as in beams, cantilevers, lintels over 1.5m span complete all as specified and directed.(Note : Reinforcement will be measured & paid seperately) |
| 31 | M&L Plain Cement Concrete 1:3:6 (40 mm graded crushed stone aggregate) type C2 as in in walls or retaining walls, any thickness, size or shape including pilasters, buttresses columns, pillars, boundary pillars and posts (including caps and bases), complete all as specified and as directed. |
| 32 | Material and Labour RCC (Nominal mix) 1:1.5:3 ( Using 20mm graded crushed stone aggregates) as in Foundations, including rafts, footings, foundation beams; plinth beams; bases for columns, etc.; basement slabs, under-reamed piles and mass concrete complete all as specified and directed. |
| 33 | M & L for Pre-cast cement concrete 1:3:6, type C-1 (using 20mm graded stone aggregate), block masonry with solid blocks of size 300x200x200mm or 300x200x100mm, having compressive strength of not less than 100 Kg/Sq Cm (As per IS-2185) exc. 10 cm in width and setting in mortar 1:6 complete all as specified and directed. |
| 34 | M & L for Pre-cast cement concrete 1:3:6 (using 16 mm graded stone aggregate), block masonry for honeycomb walling block masonary with hollow blocks exc. 10 cm in width and setting in mortar 1:4 complete all as specified and directed. |
| 35 | M & L for Providing precast cement concrete 1 : 3 : 6 type C-1 ( using 20 mm graded stone aggregate ) solid building blocks or slabs 10cm thick (with plain or interlocking joints as directed) setting in mortar, complete, in walls |
| 36 | S&F Use and waste for Formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200mm thick (Horizontal or sloping) complete all as specified and as directed. |
| 37 | M&L Use and waste of Formwork to sides of Pillars, Posts, Struts, Piers, Columns and stanchions, flat, rough finished surfaces of concrete, ( complete all as specified and as directed. |
| 38 | Formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams; and similar work; vertical or to batter all as specified & directed |
| 39 | M&L Use and waste for Formwork to Sides and Soffits of Floor or Roof Beams, Beam Haunchings, Girders, Bres-Summers, Lintels, Cantilevers, Shelves including supports, overhangs, etc. also splays between floors and beams, etc., flat, rough finished surfaces of concrete, complete all as specified and as directed. |
| 40 | S&F Anodised aluminium frame for doors, windows, ventilators with one or more rebates including joining cleat for fixing etc., complete all as specified and as directed. |
| 41 | S&F Anodised aluminium window and ventilator shutters, side hung type without sash bars, aluminium sections weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws, anodised aluminium fittings such as peg stays 150mm long (1 no.). hinges type B-21 100mm long (2 no.) suitable handle (1 no.) complete all as specified and directed .Note:- Fixing of wire mesh and glass shall be measure and paid separately under relevant items. |
| 42 | M&L Steel Ventilator with frame ,top hung shutter including hinges, steel peg stay, complete all as specified and as directed. |
| 43 | S&F 35mm thick Flush shutters, solid core construction, with block board core and plywood face panels, commercial type on both sides fitted to cowkhats complete all as specified and directed. |
| 44 | S & F in repair Stainless steel wire cloth. 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples complete all as specified and directed. |
| 45 | S & Stainless steel wire cloth. 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples complete all as specified and directed. |
| 46 | S & F 4 mm thick, sheet glass, ordinary quality and glazing with oil putty in square not exceeding 0.5 Sqm in each pane complete all as specified and as directed. |
| 47 | S & F 4 mm thick, sheet glass, ordinary quality and glazing with oil putty in square exceeding 0.5 Sqm in each pane complete all as specified and as directed. |
| 48 | S & F solid PVC door frames of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with MS square tube complete all as specified and directed. |
| 49 | S & F factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of MS tubes for top & bottom rails. MS frame shall be covered with heat moulded, plain colour PVC 'C' channel having a PVC sheet strip of 20 mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail, panelling of plain colour PVC sheet to be fitted in the MS frame welded/sealed to the stiles & rails with suitable PVC sheet beading and jointed together with solvent cement, as per specification and drawing and as directed. |
| 50 | S & F 75 mm long, stainless steel butt hinges fixed with stainless steel hinge pin etc complete all as specified and directed. |
| 51 | S & F 150 mm long, Aluminium anodised, barrel tower bolts of extruded section complete all as specified and directed. |
| 52 | S & F 150 mm size, extruded Aluminium alloy handles, fabricated type, anodised complete all as specified and directed. |
| 53 | S & F 300 mm Aluminium alloy anodised sliding door bolt with hasp & staple (bolt type) and fixing clipes of sheet, cast or extruded sections and fixing bolts of extruded sections or cast aluminium alloy, length of bolt complete all as specified and directed. |
| 54 | S & F 300 mm size MS door spring including roller plate by means of welding or screwing down complete all as specified and directed. |
| 55 | S & F Pre-Painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as per manufacturer's instruction complete all as specified and directed. |
| 56 | S & F Pre-Painted galvalume aluminum zinc coating GI based Plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in ridges/vally gutter, fixed with self tapping screws as per manufacturer's instruction complete all as specified and directed. |
| 57 | M&L Mild Steel Work in Tubular Trusses including special shaped washer etc. complete using ERW or induction butt welded tubes conform-ing to IS:1161-1979 grade St.-240, complete all as specified and as directed. |
| 58 | S&F Rolled mild steel as in Compound girders and stanchions, lattice girders, aerial masts, staging for water tanks and the like including caps, bases, splices etc. built up from two or more beam or channel sections or angles with plates, including all lattice bars, stiffeners, gusset plates, etc. and fixing complete Fe 290 Gde-E-165 quality-A complete all as specified and directed. |
| 59 | S & F Mild steel, plain, black sheet 1mm thick in wall cladding, steel gates and similar work, cut to size, holes punched; including round headed screws, clout nails or rivets and fixed to wood or steel framing with plain 40 mm lap joints with riveted or welded seams, including bending or turning up, mitred angles, etc. as required all aas required & directed. |
| 60 | S & F high strength TMT steel bars 10 mm dia., and over cut to length, bend to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia or securing with clips quality complete all as specified and directed. |
| 61 | S & F high strength Mild steel TMT bars 5mm dia and over upto and including 8mm dia in strirrups, spacers and binders spirally for hooping for columns, hooking ends and binding with mild steel wire (annealed) not less than 0.9 mm dia or securing with clips etc complete all as specified and directed. |
| 62 | S & F aluminium Anodised snap grid frame work of size 605mm x 605mm frame work for ceiling with aluminium T section of size 38mm x 25mm x 1.5mm thick for main runners, 25x25x1.5mm thick for cross runner and angle size 25x25x1.5mm thick alongwith wall suspended and including Hangers 4/2 mm dia. G.I. (upto 1200mm length) adjusting level fixed to ceiling members in proper position, fixed with aluminium staple on snap grid as per manufacturer's instructions including 6 mm thick non asbestor E-board, HSPC, designer fixed to frame complete all as specified and directed by the Engr-in-Charge. |
| 63 | M & L for 25 mm thick, plain cement concrete 1:2:4, type B-0 (using 12.5 mm graded stone aggregate) as in flooring, etc and finished the surface even and smooth without using extra cement complete all as specified and directed. |
| 64 | M&L Cement Concrete type D2 (1:4:8) using 40mm graded aggregate 75mm thick in Sub-bases, finishing concrete surfaces fair and even, complete all as specified and as directed. |
| 65 | M & L 100 mm thick cement concrete 1:4:8 type D-2( using 40 mm graded stone aggregate0as in sub base for receving the floors finishes. |
| 66 | M&L Machine pressed precast concrete interlocking paver block with grey cement and pigment any shape and size confirming to IS 15658-2006 of 60 mm thickness M-35 Grade over 100 mm sand cushion over rammed earth complete all as specified and as directed. |
| 67 | M & L for 75 mm thick, plain cement concrete 1:3:6, type C-2 (using 40mm graded stone aggregate) as in plinth protection etc, finishing cement concrete surface even and smooth without using extra cement including making joints with bitumastic filing in proportion of bitumen and sand 1:2 complete all as specified and directed. |
| 68 | M & L for non-skid, ceramic, coloured tiles 7 to 8 mm thick (square/rectangular) area of each tile exc 0.18 sqm but n.exc 0.38 sqm, in floors etc, and set & jointed in neat cement slurry and pointed in white or coloured cement to match with the shade of tiles including 15 mm thick screed bed in cement mortor 1:6 complete all as specified and directed. |
| 69 | M & L for non-skid, ceramic, coloured tiles 7 to 8 mm thick (square/rectangular) area of each tile exc 0.11 sqm but n.exc 0.18 sqm, in floors etc, and set & jointed in neat cement slurry and pointed in white or coloured cement to match with the shade of tiles including 15 mm thick screed bed in cement mortor 1:6 complete all as specified and directed. |
| 70 | M&L Glazed Ceramic Coloured Tile 450 x 350 x 7.0mm thick on Vertical Surfaces such as Skirting, Dados, Risers to Steps, etc., Set and Jointed in Neat Cement Slurry and Pointed in White or Coloured Cement to match the Shade of the Tiles over and including 10mm thick backing layer in cement mortar (1:4) complete all as specified and as directed. |
| 71 | M&L Green Marble Work 18 mm to 20mm thick (Table rubbed and polished) in border of kota stone flooring and like, Set in Screed bed of 20mm thick in Cement Mortar 1:4 including Pointing in White Cement 1:2 using Marble Dust with admixture of Pigment to match with Shade of Marble including Cutting and Polishing, including demolition of old flooring complete all as specified and as directed. |
| 72 | M & L for rendering 10 mm thick on fair faces of brick work or concrete surfaces in cement mortar 1:6 and finished the surfaces even and fair complete all as specified and directed. |
| 73 | M&L Rendering 15mm thick in Cement Mortar 1:4 on other than fair faces of Brick Walls or on Concrete Surfaces, finishing plastered surfaces Even and Smooth without using Extra Cement complete all as specified and as directed. |
| 74 | S & F water proofing compound (as approved), conforming to IS : 2645-2003, complete all as specified & directed. |
| 75 | M & L for Preparation of newly plastered surfaces of walls and applying two coats of cement base paint over a coat of alkali resistant primer complete all as specified and directed. |
| 76 | M & L for Preparation of old plastered surfaces of walls and applying one coats of cement base paint complete all as specified and directed. |
| 77 | M & L for preparing newly plastered surfaces of walls, etc and applying three coats of white wash complete all as specified and directed. |
| 78 | M & L for Preparation of new or previously untreated wood and wood based surfaces of any description, not otherwise described, over 10 cm width or girth and applying two coats of synthetic enamel paint (1st grade quality) over a coat of pink primer complete all as specified and directed. |
| 79 | M&L for Preparation of new plastered surfaces and applying two coats of oil emulsion distemper (any colour/tint) over a coat of primer over 3 mm thick wall care putty (Birla/Asian) on wall surfaces including rubbing with emmery paper to make wall surface smooth and even complete all as specified and directed. |
| 80 | M & L for Preparation of new steel surfaces of any description, over 10 cm in width or girth, not otherwise described and applying two coats of synthetic enamel paint over a coat of red oxide, zine chrome primer complete all as specified and directed. |
| 81 | M & L for Preparation of old painted steel surfaces of any description, not otherwise described, over 10 cm width or girth and applying one coat of Synthetic enamel paint complete all as specified and directed. |
| 82 | S&F in repair Toilet paper holder of brass chromium plated fixed to walls with chromium plated brass screw including necessary fixing arrangement complete all as specified and directed. |
| 83 | S & F in repair 125 mm size, shower rose, with shower arm, brass chromium plated, swival type, complete all as specified and directed. |
| 84 | S & F in repair 25 mm bore, Stop/angle valves, cast copper alloy, chromium plated, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions complete all as specified and directed. |
| 85 | S & F in repair 15 mm bore, Stop/angle valves, cast copper alloy, chromium plated, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions complete all as specified and directed. |
| 86 | S & F 15 mm bore, bib taps, fancy type, cast copper alloy, chromium plated with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule fixed in repair complete all as specified and directed. |
| 87 | S&F in repair 15 dia fancy type Brass CP mixer for mixing hot & cold water screwed down for iron pipe and fixed etc complete all as specified and as directed. |
| 88 | S & F 20 mm bore, gun metal Gate valves, with iron wheel head, Class-I, Pressure Tested of 1.5 Mpa, screwed both ends for iron pipe complete all as specified and directed. |
| 89 | S&F Rotational Moulded Polyethylene (HDPE) Water Storage Tank 1000 Litre Capacity (Cylindrical Vertical with Closed Top), Black in Colour, Three Layered Construction, hoisted and fixed in Position all specified in MES Schedule Part-I including provision of 25mm x 100mm GI nippples with check nuts for inlet, outlet wash and overflow pipe including 20 mm bore, Ball valves high pressure of PTMT with epoxy coated Aluminium rod & high density plastic ball screwed for iron pipe and including Lowering of old/unserviceable Water Storage Tank of any description, complete all as specified and as directed. |
| 90 | S&F in repair Vitreous China wash down water closet pan (ISI Marked, Ist Quality) including P or S trap (pedestal pattern), white or in matching colour of tiles (excluding flushing cistern and flush pipe) including plastic water closet seat, white or in matching colour , closed pattern with flat bottom, and cover and mild steel chromium plated or aluminized hinging device and wash down water closet complete all as specified and as directed. |
| 91 | Supply and fixing in repair 10 litre capacity low level PVC flushing cistern (any colour), syphonic action type, with inlet, ball valve, float, handle, fixed with cast iron bracket (of suitable size) and providing 32 mm dia PVC flush pipe and making all necessary connections complete as directed. |
| 92 | S&F in repair for vitreous China urinal full stall type (back or cornerwall type) complete including providing & fixing plugs bedding urinal against wall in cement mortar 1:2, securing urinals to plugs with & including 60mm long brass screw, pointing around urinal back in cement, fixing automatic flushing cistern with brackets, flush pipe ,grating and union for discharge pipe .(Exclisive of fixing supply pipe to flushing cistern, trap and waste pipe ), complete all as specified and directed . |
| 93 | M & L Vitreous china urinal partition white of size 310x700 mm.Urinal partitions slabs terminating about 40cm above floor line, fixed in repairs all as specified & directed. |
| 94 | S&F PVC connection 15mm size with PTMT nut of length 450mm complete all as specified and directed. |
| 95 | S & F in repair Health faucet (ABS Body) mild steel chromium plated suitable for 15 mm dia pipewith 1.2 Meter Long PVC Tube & Wall Hook including making connections and fixed in position complete in all respect as specified. |
| 96 | S&F Brass chromium plated tubular towel rail, 20mm dia, D type, 60,cm long between flanges as in repair complete all as specified and directed. |
| 97 | S & F in repair 600mmX450mm bevelled edge mirror of selected quality glass, mounted on 6mm thick AC building board or commercial plywood and fixed to wooden plug with chromiun plated brass screws and cup washers complete all as specified and directed. |
| 98 | S&F CPVC pipes 25 mm outer diameter of SDR 11 & plain CPVC SDR 11 fittings fixed on Walls, Ceiling or laid in Floors or any other Situation, etc complete as all specified and as directed. |
| 99 | S&F CPVC pipes 32 mm outer diameter of SDR 11 & plain CPVC SDR 11 fittings fixed on Walls, Ceiling or laid in Floors or any other Situation, etc complete as all specified and as directed. |
| 100 | Supply and Laying Steel Water Tubing 15mm Bore (dia), Galvanised, ‘Medium Grade’ with all Fittings, fixed on Walls, Ceiling or laid in Floors or any other Situation, complete as all specified and as directed. |
| 101 | Supply and Laying Steel Water Tubing 20 mm Bore (dia), Galvanised, ‘Medium Grade’ with all Fittings, fixed on Walls, Ceiling or laid in Floors or any other Situation, complete as all specified and as directed. |
| 102 | S & F 75 mm bore, PVC (SWR), Soil, waste and vent pipes, single socketed in any length with rubber ring joints fixed to walls, etc complete all as specified and directed. |
| 103 | S&F PVC (SWR) Soil, Waste and Ventilating Pipe 110mm bore (dia), single socketed, in any length with Rubber Ring Joints fixed to Walls, complete all as specified and as directed. |
| 104 | S & F 75 mm bore, PVC (SWR) bends of any radius complete all as specified and directed. |
| 105 | S & F 110 mm bore, PVC (SWR) bends of any radius complete all as specified and directed. |
| 106 | S & F 110mm bore, PVC (SWR) junction single, (Single T) equal or unequal complete all as specified and directed. |
| 107 | S&F PVC (SWR) 75 mm bore cowls and Jointing with Solvent Cement complete all as specified and directed. |
| 108 | S & F 110mm bore, PVC (SWR)Vent Cowl |
| 109 | S&F PVC(SWR) Floor Trap with 75 mm bore (dia) Outlet, with Gratings including jointing to Waste Pipe and fixed in Cement Concrete 1:2:4 (20mm graded aggregate), as in repair complete all as specified and as directed. |
| 110 | S&F Vitreous China Wash Hand Basin Pedestal type 550x400mm in size, White (Flat Back or Angle Back Type) with 32mm dia Brass Chromium Plated Waste Fitting, a pair of Cast Iron Brackets duly painted including Cutting and pinning in Ends, making good disturbed Surfaces in Cement Mortar 1:3 including taking down/out unserviceable Wash Hand Basin and connected Items, complete all as specified and as directed. |
| 111 | S&F Chromium Plated soap dish fixed to wall with necessary fixing arrangement as in repair complete all as specified and directed |
| 112 | Taking down copper/aluminium point wiring (light, fan, socket or power) complete, including fixture and fittings such as switches, ceiling roses, pendants, regulators, sockets, light fitting etc. removing materials to store for keeping in safe custody or for taking credit (credit for above items should be made as per conditions separately) and making good disturbed surfaces of walls, floors, etc. complete all as specified and directed. |
| 113 | Taking down unserviceable main switches, DBs, bus bars chambers, VTPN etc any capacity including all fittings and fixtures such as MCBs, isolator, etc and removing from site complete all as specified and directed. |
| 114 | M & L for Point wiring for one light/exhaust fan/fan point/call bell controlled by one way switch with two runs of single core 1.5 Sq.mm. (Nominal area) PVC insulated unsheathed multistranded copper conductor cable FRLSH (ISI marked) drawn through and including non metallic PVC casing capping (ISI marked) (aprox size 20/25/40mm width) surface type with all fittings/fixtures such as Tee, Bend, elbow, socketr, shaddle etc including 1.5mm thick MS sunken/terminal box including 3mm thick backelite sheet cover for fixing flush type switches, sockets, regulators etc. including provision of multistranded 1.5 Sq.mm copper conductor cable FRLSH [ISI marked] as earth wire connected to common earth dolly and earth in distribution board complete all as specified and as directed.(Note.: (i) The rate quoted is deemed to include making good the disturbed sufaces and to match the adjoining surface.) |
| 115 | All as per item No. 115.00 above but for One 3/5 pin socket outlet 6 amps point on same board complete ditto |
| 116 | All as per item No. 115.00 above but for One 3/5 pin socket outlet 6 amps on independent board complete ditto |
| 117 | All as per item No. 115.00 above but for ceiling fan Point wiring |
| 118 | All as per item No. 115.00 above but for exhaust fan Point wiring |
| 119 | All as per item No. 115.00 here in before but for one 15 Amps power point on the independent board with two runs of PVC insulated and unsheathed copper conductor cable of size 2.5 sqmm multistranded FR (ISI marked) and 2.5 sqmm PVC insulated unsheathed solid copper conductor cable FR (ISI marked) as earth lead complete ditto Please Enable Macros to View BoQ information |
| 120 | All as per item No. 115.00 here in before but for one 15 Amps power point on the independent board with two runs of PVC insulated and unsheathed copper conductor cable of size 2.5 sqmm multistranded FR (ISI marked) and 2.5 sqmm PVC insulated unsheathed solid copper conductor cable FR (ISI marked) as earth lead complete ditto Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Sep 29, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedOct 14, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 10 daysOct 16, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 12 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender