Tender For Repair To Certain Wooden/ Steel Furniture At Rts And Depot Hempur Under (East) Bareilly
Tender Value
5 Lakhs
Estimated cost
Bid Submission
20 Oct 2026
18 days left
EMD
10000
Bank guarantee accepted
Document Fee
300
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Udam Singh Nagar → Uttarakhand
EMD Exemption
Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for Repair To Certain Wooden/ Steel Furniture At Rts And Depot Hempur Under (East) Bareilly
BOQ
| Sl. No. | Item Description |
| 1 | Item Rate BoQ BoQ_Ver3.0 Item Rate Normal INR Only INR Select, Excess (+), Less (-) Less (-) Tender Inviting Authority: COMMANDER WORKS ENGINEER BAREILLY Name of Work : REPAIR TO CERTAIN WOODEN/ STEEL FURNITURE AT RTS AND DEPOT HEMPUR UNDER (EAST) BAREILLY Contract No :CWE BLY/ GE(E)/ 113 OF 2026-27 Bidder Name : SCHEDULE A(This BOQ template must not be modified/replaced by the bidder and the same should be uploaded after filling the relevent columns, else the bidder is liable to be rejected for this tender. Bidders are allowed to enter the Bidder Name and Values only ) NUMBER # TEXT # TEXT # NUMBER # TEXT # NUMBER NUMBER TEXT TEXT # NUMBER # TEXT# TEXT # NUMBER # NUMBER NUMBER NUMBER NUMBER TEXT TEXT NUMBER NUMBER NUMBER NUMBER TEXT TEXT NUMBER NUMBER NUMBER NUMBER TEXT TEXT NUMBER NUMBER NUMBER NUMBER TEXT TEXT NUMBER NUMBER NUMBER NUMBER TEXT TEXT NUMBER NUMBER NUMBER # NUMBER # TEXT TEXT NUMBER # NUMBER # DATE NUMBER # NUMBER # TEXT # Sl.No. Description Item Code / Make Quantity Units Estimated Rate Addition / Deduction Addition / Deduction Values Currency Convertion against each Item Quoted Currency in INR / Other Currency BASIC RATE In Figures To be entered by the Bidder Rs. P Excise Duty VAT Freight Charges ( Unloading & Stacking) Any Other Taxes/Duties/Levies Other Taxes 2 IIIrd Party i.e DGS&D / RITES etc Inspection Charges @0.34%+Service Tax Less for Cenvat Credit,if any respect of Supplies Under full Excise Duty Category TOTAL AMOUNT With Taxes TOTAL AMOUNT With Taxes TOTAL AMOUNT In Words |
| 2 | Bed Hard Plywood Top (FD-247): S&F of following new components of bedhard plywood top comprising outer member made of teakwood and internal frame made of cheer wood, covered both sides of board with 3.5 mm thick one side teakwood finish plywood with 12 mm thick half cut teakwood beading including dismantling of old unservicable one complete all as specified, directed and as shown on drawings: |
| 3 | (a) Plywood 4mm thick teak face on one side and other side commercial on outer face of the head board and 4mm thick plywood commercial face on both side on inner face of the head board alongwith TW beading |
| 4 | (b) Dismantling of old u/s Foot board and S&F new Foot board alongwith TW beading |
| 5 | (c) Dismantling of old u/s long rail and S&F new long rail made out of 1st class hard wood shisham/teak wood. |
| 6 | (d) S&F of top of bedhard plywood top made of 12 mm thick BWP grade with suitable screws including dismantling of old unservicable one complete all as specified, directed and as shown on drawings. |
| 7 | (e) Dismantling of old u/s legs and S&F new legs made out of 1st class hard wood shisham/teak wood alongwith nylon buffeers. |
| 8 | Table Centre (FD-274) : (a) Top made of 18 mm thick prelaminated MDF board exterior grade ISI marked duly post-formed with 0.6mm thick laminate in colour/shade as approved by Engr-in-Charge/GE with 2mm thick PVC edging fixed on two sides of Make Rehau/Pegasus/Kynex with strong bonded chemical adhesive through hot pressed machine complete including dismantling of old unserviceable one complete all as specified, directed and as shown on drawings. |
| 9 | (b) Dismantling of old u/s legs of table centre and S&F new legs made out of 1st class hard wood shisham made to shape and size. PVC shoes shall be provided where ever required complete all as specified and directed. |
| 10 | Table peg (FD -384) : (a) Top made of 18 mm thick prelaminated MDF board exterior grade ISI marked duly post-formed with 0.6mm thick laminate in colour/shade as approved by Engr-in-Charge/GE with 2mm thick PVC edging fixed on two sides of Make Rehau/Pegasus/Kynex with strong bonded chemical adhesive through hot pressed machine complete including dismantling of old unserviceable one complete all as specified, directed and as shown on drawings. |
| 11 | (b) Dismantling of old u/s legs and S&F new legs made out of 1st class hard wood shisham/teak wood along with nylon buffers. |
| 12 | (c) Dismantling of old u/s long rail/long stiffner and S&F new long rail/long stiffner made out of 1st class hard wood shisham/teak wood. |
| 13 | (d) Dismantling of old u/s short rail/short stiffner and S&F new short rail/short stiffner made out of 1st class hard wood shisham/teak wood. |
| 14 | Teapoy (FD-382): (a) Top made of 18 mm thick prelaminated MDF board exterior grade ISI marked duly post-formed with 0.6mm thick laminate in colour/shade as approved by Engr-in-Charge/GE with 2mm thick PVC edging fixed on two sides of Make Rehau/Pegasus/Kynex with strong bonded chemical adhesive through hot pressed machine complete including dismantling of old unserviceable one complete all as specified, directed and as shown on drawings. |
| 15 | (b) Dismantling of old u/s legs and S&F new legs made out of 1st class hard wood shisham/teak wood. |
| 16 | (c) Dismantling of old u/s long rail/long stiffner and S&F new long rail/long stiffner made out of 1st class hard wood shisham/teak wood. |
| 17 | (d) Dismantling of old u/s short rail/short stiffner and S&F new short rail/short stiffner made out of 1st class hard wood shisham/teak wood. |
| 18 | Table 3'X2' without drawer (FD-284): (a) Top made of 18 mm thick prelaminated MDF board exterior grade ISI marked duly post-formed with 0.6mm thick laminate in colour/shade as approved by Engr-in-Charge/GE with 2mm thick PVC edging fixed on two sides of Make Rehau/Pegasus/Kynex with strong bonded chemical adhesive through hot pressed machine complete including dismantling of old unserviceable one complete all as specified, directed and as shown on drawings. |
| 19 | (b) Dismantling of old u/s short rail/short stiffner and S&F new short rail/short stiffner made out of 1st class hard wood shisham/teak wood. |
| 20 | Chair writing (FD-280):(a) Dismantling of old u/s front legs of chairs writing and S&F of new front leg made of 1st class HW shisham, made of shape and size. PVC shoes shall be provided where ever required all as shown on drg and as directed. |
| 21 | (b) Dismantling of old u/s Rear leg and S&F new rear leg for chair writing of 1st class hard wood shisham/teak wood |
| 22 | (c) Dismantling of old u/s rails and S&F new Rails for chair writing of 1st class hard wood shisham/teak wood alongwith shoe/nylon buffers |
| 23 | (d) Dismantling of old u/s arms of chair writing/CBA and S&F new arms made of 1st class Hard wood shisham made of shape and size all as shown on drg and as directed. |
| 24 | Dismantling of old u/s back support of chair writing/CBA and S&F new back support made of 1st class Hard wood shisham made of shape and size all as shown on drg and as directed. |
| 25 | (e) Canning -M&L for recanning of the seat of chair writing in 'Godrej' pattern with 2 mm wide & 0.6 mm thick for centre portion and 4 mm wide plastic cane for borders of Make- Premier/Saha or equivalent including dismantling of old unserviceable one complete all as specified, directed and as shown on drawings. |
| 26 | Chair dining CB (FD-279): (a) Dismantling of old u/s Front Leg and S&F new Front Leg for chair dining of 1st class hard wood shisham/teak wood . |
| 27 | (b) Dismantling of old u/s Rear leg and S&F new Rear leg for chair dining of 1st class hard wood shisham/teak wood . |
| 28 | (c) Dismantling of old u/s Side/back/Leg and S&F new Side/back/ Leg for chair dining of 1st class hard wood shisham/teak wood . |
| 29 | (d) Canning -M&L for recanning of the seat of chair writing in 'Godrej' pattern with 2 mm wide & 0.6 mm thick for centre portion and 4 mm wide plastic cane for borders of Make- Premier/Saha or equivalent including dismantling of old unserviceable one complete all as specified, directed and as shown on drawings. |
| 30 | Chair easy (FD-229) :(a) Dismantling of old u/s Front/rear Leg and S&F new Front/rear Leg for chair easy of 1st class hard wood shisham/teak wood alongwith PVC shoes/buffers. |
| 31 | (b) Dismantling of old u/s Rails of seat & back and S&F new Rails of seat & back for chair easy of 1st class hard wood shisham/teak wood . |
| 32 | (c) Dismantling of old u/s Arm rest and S&F new Arm rest for chair easy of 1st class hard wood shisham/teak wood . |
| 33 | Canning (FD-229): (d) M&L for recanning of the seat & back of chair easy in 'Godrej' pattern with 2 mm wide & 0.6 mm thick for centre portion and 4 mm wide plastic cane for borders of Make- Premier/Saha or equivalent including dismantling of old unserviceable one complete all as specified, directed and as shown on drawings. |
| 34 | Polishing : Preparation of old surface with emery paper, filling the gaps with bee wax plaster of paris, applying raw siena with de-natured spirit and smoothing the surfaces with sand paper and applying two coats of french polish of superior quility all as specified and as directed to give glossy finish for the following:- |
| 35 | FD-371Side board complete all as specified and directed. |
| 36 | FD-280 Chair writing complete all as specified and directed. |
| 37 | FD-279 Chair dining CB complete all as specified and directed. |
| 38 | FD-229 Chair easy complete all as specified and directed. |
| 39 | FD-247, Bedhard Plywood Top Drg No. or similar pattern |
| 40 | FD-274 Table centre complete all as specified and directed. |
| 41 | FD-384 Table peg complete all as specified and directed. |
| 42 | FD-276 Table bed side complete. |
| 43 | FD-382 Teapoy complete all as specified and directed. |
| 44 | FD-284 Table 3'x2' without drawer complete all as specified and directed. |
| 45 | FD-281 Sofa set 04/05 seater complete all as specified and directed. |
| 46 | Charpoy GI Pipe Ply top (FD-220 )(a) S&F of ply top of size 1980mmx900mm of 12 mm thick BWP grade ISI marked plywood including two Nos flat iron of Size 25x4mmx900mm long fixed on long rail along short rail on equal distance of bracing the long rails with and including 14 (Fourteen) Nos of round headed steel nuts, bolts and washers of appropriate size by making holes with drill machine, steel iron surfaces shall be painted with 02 coats of black synthetic enamel paint over and including a coat of primer including taking down and removing old unserviceable ply top complete all as specified and directed. |
| 47 | FD-220 :(b) Provide Long rail made of 32 mm bore GI tubing medium grade ISI marked 1.88 metre long, threaded at both ends and fixing to 3 way 32 mm size GI elbow of charpoy duly threaded complete all as specified and as directed . Make of Tubing : Swastic/Jindal/Tata or ISI Marked. |
| 48 | FD-220 :(c) Conversion of 32 mm bore long rail obtained from dismantling of item No. 21.10 above into two numbers short rail after cutting and threading both ends and fixing to 3 way 32 mm dia existing elbow complete all as specified and directed. |
| 49 | FD-220 :(d) Conversion of 32 mm bore short rail obtained from taking down/dismantling of u/s leg of charpoy dismantling of item No. 21.20 above into one legs including fixing to 3 way 32 mm dia at one end threaded and cover the other end with hard rubber / PVC shoe alround complete all as specified and directed. |
| 50 | FD-220:(e) Taking out old u/s and broken existing elbow 3 way from the GI charpoy and S&F new 3 way elbow of 32 mm bore dia, medium weight, ISI Marked complete all as specified and directed .Make : Swastic/Jindal/Tata or ISI Marked. |
| 51 | FD-220:(f) Taking out old u/s and broken existing check nuts from the GI charpoys and S&F new checknuts of 32 mm bore and 6mm thick, medium weight, complete all as specified and directed. |
| 52 | FD-220: (g) S&F MNF clamp made out of 25x3mm weleded to GI Charpoy two nos in each leg as per drg.The end of lower clamp shall be closed with 16mm dia 3mm thick washer welded complete all as specified and directed. |
| 53 | FD-220:(h) S&F round bottom disc 50mm dia, 3mm thick by welding around to bottom legs including removing old u/s broken disc complete all as specified and directed. |
| 54 | Table office offrs steel (FD-1003) : (a) Top made of 18 mm thick prelaminated MDF board exterior grade ISI marked duly post-formed with 0.6mm thick laminate in colour/shade as approved by Engr-in-Charge/GE with 2mm thick PVC edging fixed on two sides of Make Rehau/Pegasus/Kynex with strong bonded chemical adhesive through hot pressed machine. |
| 55 | Table office clk steel [ FD-381] :(a) Top made of 18 mm thick prelaminated MDF board exterior grade ISI marked duly post-formed with 0.6mm thick laminate in colour/shade as approved by Engr-in-Charge/GE with 2mm thick PVC edging fixed on two sides of Make Rehau/ Pegasus/ Kynex with strong bonded chemical adhesive through hot pressed machine. |
| 56 | Almirah steel large (FD-1031) (a) S&F in repairs for locking arrengement with 65mm brass 6 levers for almirah steel medium/large complete all as specified and directed. (Make Harison/Godrej or equivalent). |
| 57 | (b) S&F in repair handle of cast iron CP 125mm long to almirah medium/large steel complete all as specified and directed. |
| 58 | (c) Repair to shutter of almirah large/med steel by straightening of dented portion and by replaceing the broken butt hinges complete all as specified and as directed |
| 59 | Locker bed side steel (FD-1029):(a) Dismantling old u/s single door leaf and provn of new front door made of 1mm thick MS sheet duly painted with two coats of synthetic enamel paint over a coat of red oxide primer and providing CP handle and hasp and staple as shown in drg complete all as specified and directed. |
| 60 | (b) S&F in repair MS CP handle 125mm long as shown in drg complete all as specified and directed. |
| 61 | (c) S&F repair hasp and staple 75mm long MS,chromium plated as shown in drg complete all as specified and directed. |
| 62 | Chair CB steel with Arm [FD-75]: (a) Taking down existing old u/s seat of chair and S&F new seat duly polished with one coat black polish and canned as per Godrej pattern with 2 mm wide with 4 mm border (Make Primier/Shah or equivalent) seat to fixed with required screws and four numbers of rubber shoes at bottom of frame shall be provided where ever required. Frame of chair shall be painted a coat of synthetic enamelled paint before fixing of seat as shown in drg complete all as specified and directed. |
| 63 | (b) back of chair CB steel with arm and rubber cap on top of frame of the chair shall be provide where ever required all as shown in drg complete all as specified and directed. |
| 64 | FD-75 (c) Taking down old u/s arm of chair CB steel and S&F new wooden handle arm to chair CB steel duly painted black polish all as shown in drg complete all as as specified and directed (Set of two) |
| 65 | FD-75 (d) S&F flat iron stiffner 25mmx535mmx3mm thick shall be welding at bottom of seat/top of back for chair CB steel with or without arm duly painted black enamel paint all as shown in drg complete all as specified and directed. |
| 66 | Chair verandah (FD-359): Canning - M&L for recanning of the seat and back of chair varandah in 'Godrej' pattern with 2 mm wide & 0.6 mm thick for centre portion and 4 mm wide plastic cane for borders of Make- Premier/Saha or equivalent including dismantling of old unserviceable one complete all as specified, directed and as shown on drawings. |
| 67 | PAINTING : M&L for prepration of old painted/steel surfaces by wire brushing/scratching dented portion and applying two coat of synthetic enamel paint with sprayer complete all as specified and directed to give a glossy finish for the following items:- |
| 68 | FD-1031 Almirah large steel with shelves external & internal complete all as specified and directed |
| 69 | FD-1032 Almirah steel medium with shelves external & internal complete all as specified and directed |
| 70 | FD/E6/MAP/18 Almirah large steel MAP complete all as specified and directed |
| 71 | FD-1003 Table office officer steel complete all as specified and directed |
| 72 | FD-381Table office clerk steel complete all as specified and directed |
| 73 | FD-1029 Locker bed side steel complete all as specified and directed |
| 74 | (FD-359 Chair verandah complete all as specified and directed Total in Figures 0.0 0.0 INR Zero Only 4.0 Construction of chamber for 100mm sluice plates item5 10.0 Nos Quoted Rate in Figures Select 0.0 0.0 Zero Only Quoted Rate in Words INR Zero Only Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Sep 29, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedOct 20, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 18 daysOct 27, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 25 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender