Tender For Repair To Joinery, Sanitary Fittings, Tank Cleaning, False Ceiling, Roofing Tiling And Misc Work At Cottongreen, Sion And Pavanika Kalina, Santacruz And Airport Tech Area At Af Stn Mumbai Under Ge (Af) Thane
Tender Value
23 Lakhs
Estimated cost
Bid Submission
12 Oct 2026
9 days left
EMD
46000
Bank guarantee accepted
Document Fee
500
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Thane → Maharashtra
EMD Exemption
Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for Repair To Joinery, Sanitary Fittings, Tank Cleaning, False Ceiling, Roofing Tiling And Misc Work At Cottongreen, Sion And Pavanika Kalina, Santacruz And Airport Tech Area At Af Stn Mumbai Under Ge (Af) Thane
BOQ
| Sl. No. | Item Description |
| 1 | Dismantling, floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises and removing debris outside MoD land, complete all as specified and directed by Engineer-In-Charge. Note :- Removing of electric switches & sockets boards, casing caping carefully from wall surface and refixing in without damage to the same position, no extra cost will be paid on this account. |
| 2 | Demolition of cement concrete (unreinforced) in ground floor and paving n.exc 15 cm thickness (below or above ground level) and removing debris outside MoD land, complete all as specified and directed by Engineer-In-Charge. |
| 3 | M&L for 25 mm thick cement concrete type B-1, 1:2:4 (20mm graded aggregate) as in floor complete all as specified and directed by Engineer-In-Charge. |
| 4 | Material and labour for machine cut kota stone slab flooring 20-25mm thick over cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete including screed bed or bedding layer of mortar 15mm thick for laying floor finishes with CM 1:6, complete all as specified and directed by Engineer-In-Charge. |
| 5 | M&L for machine cut kota stone slab 20-25mm thick as in riser of steps,skirting,dado and pillar laid over cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing & polishing and rendering backing coat on vertical surface in 10mm thick CM 1:3 to receive slab complete all as specified and directed by Engineer-In-Charge. |
| 6 | M & L for 20mm thick granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, window-cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite, complete all as specified and directed by Engineer-In-Charge. |
| 7 | M & L for 20mm thick granite (of any type) work (table rubbed and polished) for wall lining (veneering to wall) 12mm thick in cement mortar (1:3) and pointing with white cement (1:2) using marble dust with admixture of pigment to match with shade of granite, complete all as specified and directed by Engineer-In-Charge. |
| 8 | M&L for Virified Ceramic tiles light shade 10 mm thick (square/ rectangular) polished, area of each tiles exceeding 0.42 sqm but not exceeding 1.00 sqm, in floors & skirting etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match including screed bed or bedding layer of mortar 15 mm thick for laying floor finishes with C M 1:6 complete all as specified and directed by Engineer-In-Charge. |
| 9 | M&L for Glazed ceramic coloured tiles in vertical surfaces of size 350x 250x 7mm/ 450X 350X 7mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match including rendering backing coat on vertical surface of wall in 10mm thick CM 1:3 to receive wall tiles, complete all as specified and directed by Engineer-In-Charge. |
| 10 | Non - skid Ceramic tiles 7 to 8 mm thick (square/rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured to match including screed bed or bedding layer of mortar 15 mm thick for laying floor finishes with CM 1:6 complete all as specified and directed by Engineer-In-Charge. |
| 11 | M&L for post construction Anti termite treatment along the external wall below concrete or masonary apron using chemical emulsion @ 2.25 litres per linear metre including drilling and plugging holes etc in apron, complete all as specified and directed by Engineer-In-Charge. |
| 12 | M&L for post construction Anti termite treatment at points of contact of wood work by chemical emulsion (in oil or kerosene based solution) @ 0.5 litre/hole by drilling 6mm dia holes at a downward angle of 45 degree at 150mm centre to centre and sealing the same complete all as specified and directed by Engineer-In-Charge. |
| 13 | Taking down chowkats or frame n.exc 1.5 sqm each with shutters (without taking off shutters from the frames), complete all as specified and directed by Engineer-In-Charge. |
| 14 | Taking down shutters without taking off chowkhat from frames exc 1.5 sqm but n exc 4 sqm each, complete all as specified and directed by Engineer-In-Charge. |
| 15 | S&F for pressed steel frames of sizes 125x60mm for doors with one or more rebates including necessary fixing lugs,hinge,lock strike olate etccomplete all as specified and directed by Engineer-In-Charge. |
| 16 | S&F 30 mm thick, flush shutters, solid core construction, with block board core and plywood face panels, commercial type on both sides complete all as specified and directed by Engineer-In-Charge. |
| 17 | S&F 30mm thick 2nd class Hard wood Glazed and Skelton shutters, open rebated and prepared to receive glass, gauze etc(without sash bars) edges of framing plain, chamfered or rounded, fitted with cut and mitered beads for securing glass etc, sizes of members of shutters as specified in SSR Part-I, Section 8, clause 8.24(a) and fitted to chowkats complete all as specified and directed by Engineer-In-Charge. |
| 18 | S&F stainless steel wire cloth 0.36 mm nominal dia of wire and average width of aperture 1.14 mm fixed with stainless steel wire staple complete all as specified and directed by Engineer-In-Charge. |
| 19 | M&L for preparartion of new surfaces of wood exceeding 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide, zinc chrome primer complete all as specified and directed by Engineer-In-Charge. |
| 20 | S&F door sliding bolt aldrop 250 mm long aluminium anodised Make-classic/Shalimar etc equivalent ISI Marked complete all as specified and directed by Engineer-In-Charge. |
| 21 | S&F mild steel 300mm ordinary rat tail rod pettern springs including roller and roller plate complete all as specified and directed by Engineer-In-Charge. |
| 22 | M&L for 25 x 3mm FI holdfasts complete all as specified and directed by Engineer-In-Charge. |
| 23 | Cutting holes in brick walls built in cement mortar depth of embedded portion of hold fast or lugs measured from the face of the jamb in to the wall exc half brick wall but n. exc one brick wall for in surting hold fasts and making good complete all as specified and directed by Engineer-In-Charge. |
| 24 | S & F butt hinges heavy weight cold rolled mild steel of size 100 mm by welding to existing frame including taking down old hinges complete all as specified and directed by Engineer-In-Charge. |
| 25 | S&F 150 mm size of handle extruded aluminium alloy handle febricated type anodised complete all as specified and directed by Engineer-In-Charge. |
| 26 | S&F aluminium andodized, 150mm length of bolt barrel tower bolts of extruded section complete all as specified and directed by Engineer-In-Charge. |
| 27 | S&F floor door stoppers of aluminium alloy body and toungue anodized with hard drawn steel spring over all length 140mm complete all as specified and directed by Engineer-In-Charge. |
| 28 | Repairs to Aluminium window shutters of any description easing & adjusting without taking down area exc 1 sqm but n. exc 2 sqm incl repairs to lock , roller,glass wool,rubber biddings, refixing wiremesh excl glass etc complete all as specified and directed by Engineer-In-Charge. |
| 29 | Repairs to Aluminium door shutters of any description easing & adjusting without taking down or taking down area exc 1 sqm but n. exc 3 sqm incl repairs to floor spring, hydraulic door closer, lock, pivot, Hinges, neoprine rubber,glass wool,rubber biddings, refixing etccomplete all as specified and directed by Engineer-In-Charge. |
| 30 | M&L Providing and fixing Powder coated aluminium (minimum thickness of powder coating 50 micron) work for doors, windows,ventilators and partitions (Fixed portions) with extruded built up standard tubular sections/appropriate Z sections and other sections of approved make conforming to IS: 733 and IS:1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight,mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing/ paneling,Aluminium composite panel,C.P. brass/ stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-Chief |
| 31 | S&F 3 mm thick sheet glass ordinary quality and glazing with oil putty/wooden lapping in square not exc 0.58 Sqm each in each pane complete all as specified and directed by Engineer-In-Charge. |
| 32 | S & F 3 mm thick Figure glass/ tinted glass ordinary quality and glazing with oil putty/wooden lapping in square not exc 0.58 Sqm each in each pane, lovers etc complete all as specified and directed by Engineer-In-Charge. |
| 33 | M&L for solid PVC door frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with MS square tube, suppling & fixing will be painted to match with printed sheet complete all as specified and directed by Engineer-In-Charge. |
| 34 | Factory made solid panel pvc door shutter 30mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails, M.S. frame shall be covered with heat moulded palin colour PVC `C' channel heaving a PVC sheert strip of 20mm width suck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bbottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S frame wedded/ sealed to the stiles, & rails with suitable PVC sheet beading, and joined together with solvent cement, suppling & fixing in the frame at site as per specification & drawing, complete all as specified and directed by Engineer-In-Charge. Make : Rajshri or Equivalint |
| 35 | S&F Butt hinge, medium weight, cold rolled mild steel of 75 mm size complete all as specified and directed by Engineer-In-Charge. |
| 36 | Resecuring without taking down chowkhats or frams exc 1.50 sqm but n exc 4 sqm each complete all as specified and directed by Engineer-In-Charge. |
| 37 | S&F in repairs powder coated aluminium frames incl sliding tracks, etc for doors, windows, ventilators, partitions with one or more rebates including jointing cleats for fixing, fittings like hinges, handles and locks, etc complete all as specified and directed by Engineer-In-Charge. |
| 38 | Neoprene/ EPDM rubber gasket for aluminium frame for doors, windows, Ventilators etc complete all as specified and directed by Engineer-In-Charge. |
| 39 | Hacking out old broken glass of any thickness, size, quality or description from metal /wooden frame including punching or drilling out old glazing pins/spring clips and providing and fixing new ones etc complete all as specified and directed by Engineer-In-Charge. |
| 40 | S & F in repairs stainless steel wire cloth 0.36 mm nominal dia of wire and average width of aperture 1.14 mm fixed with stainless steel wire staplecomplete all as specified and directed by Engineer-In-Charge. |
| 41 | S&F in repairs door closer aluminium (*extruded section) body hydraulically regulated designation No.3, universal type, suitable for door shutters of 851 to 1000 mm in width and of weight between 61 to 80 kg and fixed complete all as specified and directed by Engineer-In-Charge. |
| 42 | S & F in repairs floor door stopper of aluminium alloy body 150 mm length, and tounge, anodised, with hard drawn steel spring , fixed in floor complete all as specified and directed by Engineer-In-Charge. |
| 43 | M & l in repairs for Plywood 18mm thick grade BWR type BB fixed with screws to timber frame ,Al frame etc complete all as specified and directed by Engineer-In-Charge. |
| 44 | Supply and fixing for 0.9mm thick decorative Laminate type 1 of any thickness of surface finish, colour and pattern as approved, fixed with approved adhesive on plywood as per manufacturer instruction and complete all as specified and directed by Engineer-In-Charge. |
| 45 | M& L in repairs Double action floor spring hydraulically regulated made up of minimum 1.25 mm thick aluminium alloy sheet foundation box, main body with stainless steel cover, governing pivot made of brass, other parts made of mild steelheavy duty and fixed complete all as specified and directed by Engineer-In-Charge. |
| 46 | Extra over rates for external teak wood lipping 6 mm thick fixed with nails complete all as specified and directed by Engineer-In-Charge. |
| 47 | M & L in repairs (wooden ) fillet work using 2nd class hard wood exc 6 & n. exc 13 sq.cm fixed with screw, plane fillet square, rectangle in section clean swan, secuared with nails or brads complete all as specified and directed by Engineer-In-Charge. |
| 48 | S&F in repairs aluminium anodised barrel towel bolts of extruded section of length 150 mm including taking down old unserviceable barrel tower bolts complete all as specified and directed by Engineer-In-Charge. |
| 49 | S & F in repairs 300 mm Aluminium alloy anodised sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections including taking down old sliding door bolt complete all as specified and directed by Engineer-In-Charge. |
| 50 | S & F in repair 300 mm size mild steel ordinary rat tail, rod pattern springs including roller and roller plate complete all as specified and directed by Engineer-In-Charge. |
| 51 | S & F in repair aluminium extruded alloy handles fabricated type anodised of size 150 mm including taking down old handles complete all as specified and directed by Engineer-In-Charge. |
| 52 | S & F in repair hasp and staple safety type of size 100 mm of aluminium anodized including taking down old hasp and staple complete all as specified and directed by Engineer-In-Charge. |
| 53 | Re-securing or easing and adjusting without taking down shutters of any description and size complete all as specified and directed by Engineer-In-Charge. |
| 54 | S & F 20 in repair mm dia aluminium anodised tubular curtains rod with powder coated including brackets and taking down old curtain rod complete all as specified and directed by Engineer-In-Charge. |
| 55 | S&F looking mirror size 600 mm x 450 mm of selected quality glass, 5.5 mm thick, mounted on 6 mm thickAC building board commercial ply wood with PVC frame all round fixed with chromium plated brass screws including taking down old looking mirror complete all as specified and directed by Engineer-In-Charge. |
| 56 | S & F Hat pegs Brass, solid body, 125mm to 175 mm etc complete all as specified and directed by Engineer-In-Charge. |
| 57 | S & F in repairs 40 mm dia cupboard knobs fixed with nut, screw and washer of mild steel bright finished complete all as specified and directed by Engineer-In-Charge. |
| 58 | M & L for welding in repairs to roof truss,rafters , purlins,steel gates/ windows / doors exc 2.5 cm but not exc 5.00 cm in length and thickness of metal to be welded exc 9 mm but n exc 20 mm [height of roof truss,rafter / perlins 12m to 15 m] complete all as specified and directed by Engineer-In-Charge. |
| 59 | Cleaning of PVC tank of capacity exc 250 Ltrs and up to and including 500 Ltrs by flushing out water cleaning & removing of sludge, scale mud etc from wall & floor by rubbing with brushes, cleaning with concentrated hydrochloric acid or caustic soda etc complete & finally washing with fresh water, including fixing float valve,check nut and tightening the pipes joints including writing date of cleaning with white synthetic enamel paint and removing sludge, scale mud etc to a distance not exceeding 50 Metre and depositing complete all as specified and directed by Engineer-In-Charge. |
| 60 | All as per item No 59 here-in-above but capacity of tank exc 500 Ltrs and up to and including 1000 Ltrs complete all as specified and directed by Engineer-In-Charge. |
| 61 | All as per item No 59 here-in-above but capacity of tank exc 1000 Ltrs and up to and including 2000 Ltrs complete all as specified and directed by Engineer-In-Charge. |
| 62 | All as per item No 59 here-in-above but capacity of tank exc 2000 Ltrs and up to and including 5000 Ltrs complete all as specified and directed by Engineer-In-Charge. |
| 63 | Fixing only in repairs float valve upto 25mm bore obtained from dismantling complete all as specified and directed by Engineer-In-Charge. |
| 64 | S&F 500 Liters capacity, rotational molded, polythene water storage tank (Cylindrical vertical with closed top) hoisted and fixed on roof in position all as specified in SSR Part I over existing PCC platform including all fitting such as connection pipe pieces with GI tank nipple for inlet, outlet, washout and overflow etc and including fixing only ball valves, dismantling of existing water tank, complete all as specified and directed by Engineer-In-Charge. |
| 65 | All as per item No. 64 here-in-above but capacity of tank 1000 Ltrcomplete all as specified and directed by Engineer-In-Charge. |
| 66 | All as per item No. 64 here-in-above but capacity of tank 2000 Ltr complete all as specified and directed by Engineer-In-Charge. |
| 67 | Supply only float valve upto 25mm bore obtained from dismantling complete all as specified and directed by Engineer-In-Charge. |
| 68 | S&F in repairs 15 mm size bib tap cast copper alloy, chromioum plated fancy type screwed down, with capston head, screwed for iron pipe complete all as specified and directed by Engineer-In-Charge. |
| 69 | S & F in repairs 15 mm size pillar taps, cast copper alloy chromium plated, fancy type, screwed down high pressure, with or without lettered ‘Hot’ or ‘Cold’ with long screwed shanks and fly nuts, screwed for iron pipe complete all as specified and directed by Engineer-In-Charge. |
| 70 | S&F in repairs 15 mm size stop valve or angle valve cast copper alloy, chromioum plated fancy type, screwed down, high pressure with capston head, screwed both ends for iron pipe or for union complete all as specified and directed by Engineer-In-Charge. |
| 71 | S&F in repairs 15 mm size stop valve with long shank (consealed type) cast copper alloy, chromioum plated fancy type, screwed down, high pressure with capston head, screwed both ends for iron pipe or for union complete all as specified and directed by Engineer-In-Charge. |
| 72 | S & F in repair 20 mm size gun metal, globe or gate valve with iron wheel head screwed both ends for iron pipe and including taking down old gate valve complete all as specified and directed by Engineer-In-Charge. |
| 73 | S & F Grating doom 100mm dia of PTMT (Minimum weight 25gms) complete all as specified and directed by Engineer-In-Charge. |
| 74 | S & F PVC connection 15 mm size with PTMT nuts on both end, length 600 mm, including taking down old PVC connection complete all as specified and directed by Engineer-In-Charge. |
| 75 | S&F 15 in repair mm size brass chromium plated shower rose 125 mm dia with or without / swivel joints, fixed in position including taking down old shower rose complete all as specified and directed by Engineer-In-Charge. |
| 76 | S&F in repairs 10 Ltr capacity PVC syphonic action type flushing cistern low level with inlet ball valve, float and handle, fixed in position and connecting including taking down old cistern complete all as specified and directed by Engineer-In-Charge. |
| 77 | S&F Vitreous China wash down water colset (pedestal pattern) and trap white including fixing bolts,WC seat cover of fixed with aluminium or ms chromium plated complete all as specified and directed by Engineer-In-Charge. |
| 78 | S&F Vitreous China wash down water colset (Squat pattern) white complete as fixed in repair excluding flushing cistern and flush pipe \\"Orissa\\" pattern size 580x400 with integral footrest inject connection to trap antisyphonage etc complete incl joint between flushing pipe and socket of WC complete all as specified and directed by Engineer-In-Charge. |
| 79 | S&F vitreous china white wash hand basin 550 mm x 450 mm including all necessary fitting such as 15 mm CP pillar cock fancy type, CP waste coupling 32mm dia, PVC waste pipe and brackets including supply and grouting 6 to 8 mm dia GI racket bolt at the back side of WHB and making good existing surfaces, including taking down old wash hand basin complete all as specified and directed by Engineer-In-Charge. |
| 80 | S&F in repairs plastic water closet seat cover, white or black colour closed pattern with flat bottom including taking down old seat cover complete all as specified and directed by Engineer-In-Charge. |
| 81 | Supply and fix in repairs 15 mm size wall mixer, for mixing hot & cold water, cast copper alloy, chromium plated with capstan head comprising bib tap with all connected accessories, fixed complete all as specified and directed by Engineer-In-Charge. |
| 82 | Supply and laying in repairs 16 mm outer diameter CPVC pipes SDR 11 & plain CPVC SDR 11 fittings on walls/ceiling or laying in floors complete all as specified and directed by Engineer-In-Charge. |
| 83 | Supply and laying in repairs 20 mm outer diameter CPVC pipes SDR 11 & plain CPVC SDR 11 fittings on walls/ceiling or laying in floorscomplete all as specified and directed by Engineer-In-Charge. |
| 84 | Supply and fix in repairs 32 mm size waste coupling of PTMT for wash hand basin / urinal / sink complete all as specified and directed by Engineer-In-Charge. |
| 85 | Supply and fix in repairs Health Faucet (ABS body) mild steel chromium plated suitable for 15mm dia pipe with 1.25metre long flexible tube and ABS wall hook including making connections and fixed in position complete all as specified and directed by Engineer-In-Charge. |
| 86 | S&F in repairs sheet glass assembly consisting of 5.5mm thick sheet glass shelf 12cm wide with chromium plated bracket guard and railing 60cm long etc complete all as specified and directed by Engineer-In-Charge. |
| 87 | Supply and fix in repairs 15 mm size wash hand basin mixer, for mixing hot & cold water, cast copper alloy, chromium plated with capstan head comprising single hole bib tap with all connected accessories, fixed complete all as specified and directed by Engineer-In-Charge. |
| 88 | S & F in repairs Stack clamps out of 50mm by 5 mm flat iron and 16mm dia round iron stays, including bolts and nuts and securing ends of stays to wall or roof for 100 mm dia pipe, complete all as specified and directed by Engineer-In-Charge. |
| 89 | S&F in repairs Brass chromium plated tubular towel rail 20mm dia & 60cm long between flanges of complete all as specified and as directed by Engineer-In-Charge. |
| 90 | Dismantling plain or corrugated steel sheeting,any gauge,thickness, including Nainital or similar pattern roof covering is any positioncomplete all as specified and directed by Engineer-In-Charge. |
| 91 | S & F Pre- painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering, fixed with self tapping screws as specified etc using necessary scaffolding upto height 20m as complete all as specified and directed by Engineer-In-Charge. |
| 92 | S&F pre-painted Galvalume aluminium zinc coating GI based plain steel sheet 0.50 mm thick of an colour having tensile strength of 550 Mpa as in roof ridge covering, fixed with self tapping screws using necessary scaffolding upto height 20m complete all as specified and directed by Engineer-In-Charge. |
| 93 | Dismantling wrought iron or mild steel work of any description not otherwise provided complete all as specified and directed by Engineer-In-Charge. |
| 94 | S & F for Steel work in tubular trusses and similar works including special shaped washer etc. complete using ERW or induction butt welded tubes conforming to I. S.1161-1979 grade St.-240,etc for ornamental and intricate design complete all as specified and directed by Engineer-In-Charge.(for Height of building max 20m) |
| 95 | S & F for Plates (plain ) channels, square cut or notched (ordinary and counter sunk) forming holes, with riveted,bolted or welded attachment, Fe 410-W (Gde-E-250) quality-A,flat iron, etc with ornamental and intricate design complete all as specified and directed by Engineer-In-Charge. |
| 96 | M&L for Preparation of new steel surface not otherwise described and applying two coats of Aluminium paint over a coat aluminium red oxide primer complete all as specified and directed by Engineer-In-Charge. |
| 97 | M&L for preparation of old decorated steel surfaces and applying one coat of synthetic enamel paint complete all as specified and directed by Engineer-In-Charge. |
| 98 | M & L for welding in repairs to roof truss,rafters, purlins,steel gates/ windows / doors exc 2.5 cm but not exc 5.00 cm in length and thickness of metal to be welded exc 9 mm but n exc 20 mm [height of roof truss,rafter / perlins 12m to 15 m]complete all as specified and directed by Engineer-In-Charge. |
| 99 | Dismantling of wall and ceiling boards (PVC solid wall panelling, fibre, pulp, insulation, etc) or insulation boards/slabs/blankets, any thickness, including cover fillet, complete all as specified and directed by Engineer-In-Charge. |
| 100 | S & F PVC False ceiling 6mm thick solid EPS stuck to 1mm printed PVC sheet, grid made of Aluminium/G.I./M.S. as per specification and drawing, complete all as specified and directed by Engineer-In-Charge. |
| 101 | M&L in repairs for Anodised aluminium snap grid frame work of size (605mm*605mm ) for false ceiling complete all as specified and directed by Engineer-In-Charge. |
| 102 | M&L in repairs for Hangers 6mm dia. G.I. (upto 1200 mm length) size of grid (605mm*605mm ) adjusting level fixed to roof slabs by means of ceiling cleats made out of G.I.Flat 40*3 mm size 60 mm long and expansion hold fastners 12.50mm dia. 40mm long complete all as specified and directed by Engineer-In-Charge. |
| 103 | S & F Solid PVC Wall Lining consisting of 5mm thick Plain colour PVC sheet inclusive of solvent cement and fixing at site on PVC frame as per specifications and drawing as per specification and drawing, complete all as specified and directed by Engineer-In-Charge. |
| 104 | S & F 5mm thick PVC sheet fillet of width 35mm for wall paneling inclusive of wall fixing on to wall to make PVC Frame as per specification and drawing, complete all as specified and directed by Engineer-In-Charge. |
| 105 | M&L for light shade vitrified ceramic tiles 8-10 mm thick (square/rectangular) polished area of each tiles not exceeding 0.36 sqm in floor & skirting etc set and jointed in neat cement slurry and pointed in white or coloured cement to match including screed bed or bedding layer of mortar 15 mm thick for laying floor finishes with C M 1:6 complete all as specified and directed by Engineer-In-Charge. |
| 106 | S & F in repairs Mortice lock with two levers (vertical type), brass body 100 mm length of latch and fixed complete all as specified and directed by Engineer-In-Charge. |
| 107 | M & l in repairs for Plywood 12mm thick grade BWR type BB fixed with screws to timber frame ,Al frame etc complete all as specified and directed by Engineer-In-Charge. |
| 108 | S&F in repairs brass mortice lock, vertical type, size 100 mm , 4 levers with 2 keys complete all as specified and directed by Engineer-In-Charge. |
| 109 | S & F in repairs Rim latch (125 mm size of latch) with two levers of brass body stone enamelled finish , with brass knob or lever handle and fixed complete all as specified and directed by Engineer-In-Charge. |
| 110 | S & F stainless steel butt hinges medium weight SS of size 100 mm by welding to existing frame including taking down old hinges complete all as specified and directed by Engineer-In-Charge. |
| 111 | M & L for fixing 6 mm thick plywood fixed with screw incl necessary cutting and waste complete all as specified and directed by Engineer-In-Charge. |
| 112 | S & F in repairs aluminium anodised brackets powder coated to match with rod for curtain rod of 20mm dia complete all as specified and directed by Engineer-In-Charge. |
| 113 | S & F in repair 20 mm size gun metal, globe or gate valve with iron wheel head screwed both ends for iron pipe and including taking down old gate valve complete all as specified and directed by Engineer-In-Charge. |
| 114 | S & F in repair PVC connection 15 mm size with PTMT nuts on both end, length 450 mm, including taking down old PVC connection all as specified and as directed. |
| 115 | Demolition of brick work or stone/boulder masonary built in cement mortor including all quoins,arches,pillars etc complete all as specified and directed by Engineer-In-Charge. |
| 116 | M & L for brick work with old size fly ash bricks, straight or covered or plan exc 6m mean radius built in CM 1:6 complete all as specified and directed by Engineer in Charge. |
| 117 | Rendering 15mm thick in cement mortar 1:6 on any face of Brick walls or concrete surfaces, finished even and smooth without using extra cement complete all as specified and directed by Engineer-In-Charge. |
| 118 | Preparation of newly plastered surfaces of walls etc., and applying two coats of cement base paint complete all as specified and directed by Engineer-In-Charge. |
| 119 | Supply and fix in repairs 40 mm size waste coupling of PTMT for wash hand basin / urinal / sink complete all as specified and directed by Engineer-In-Charge. |
| 120 | S&F in repair sinks with drainage board made of stainless steel Imm thick kitchen or laboratory with plugs, washers and wastes, including bedding in cement mortar to dwarf wall or including fixing cantilever brackets and connecting union to pipe overall size 915mm x 460mm bowl size 410mm x 330mm x 160mm complete all as specified and directed by Engineer-In-Charge. Note : 1.The contractor shall deploy skilled tradesman i.e. carpenter, plumber , mason , welder etc with his helper all workers need to be having police verification for Airport entry (MIAL) and required T&P , 2. In case of failure to attend the required maintenance work within 48 hrs the contractor shall be charged @400 Rs per Work. 3. After completion of work service to the building the contractor will clean all the working site and remove all debris, credit items and construction materials from the site immediately and shall be thrown away outside the MoD land. Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Sep 29, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedOct 12, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 9 daysOct 19, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 16 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender