Tender For Certain Repair To Otm Bldgs At Air Force Station Highground Under Age (I) Highground Chandigarh
Tender Value
18 Lakhs
Estimated cost
Bid Submission
13 Oct 2026
10 days left
EMD
36000
Bank guarantee accepted
Document Fee
500
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Chandigarh → Chandigarh
EMD Exemption
Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for Certain Repair To Otm Bldgs At Air Force Station Highground Under Age (I) Highground Chandigarh
BOQ
| Sl. No. | Item Description |
| 1 | Taking down chowkhats or frames with shutters (without taking off shutters from the frame), not exceeding 1.5 Sqm each and removal, including making good the disturbed surface in CM(1:4) and finishing as per existing specifications and removal of debris outside MOD land, complete all as specified and directed. |
| 2 | Taking down chowkhats or frames with shutters (without taking off shutters from the frame), exceeding 1.5 sqm but not exceeding 4 sqm each and removal, including making good the disturbed surface in CM(1:4) and finishing as per existing specifications and removal of debris outside MOD land, complete all as specified and directed. |
| 3 | Taking down shutters of any description not exceeding 1.0 Sqm each, from chowkhats/frames and removal to store for reuse or credit, complete all specified and directed |
| 4 | Taking down shutters of any description exceeding 1.0 Sqm but not exceeding 2.0 Sqm each, from chowkhats/frames and removal to store for reuse or credit, complete all specified and directed |
| 5 | Supply and fixing factory made pressed steel frames for doors with two rebates, of size 125 mm x 60mm, made out of 1.25mm thick sheet, including one shop coat primer and necessary fixing lugs, hinges, lock strike plate, etc, complete all as specified and directed. |
| 6 | Supply and fixing factory made pressed steel frames for doors with two rebates, of size 105 mm x 60mm, made out of 1.25mm thick sheet, including one shop coat primer and necessary fixing lugs, hinges, lock strike plate, etc, complete all as specified and directed. |
| 7 | Supply and fixing, Solid PVC Door Frame of size 50mm x 47mm made out of 5mm thick plain colour PVC sheet reinforced with M.S. Square tube, as per specification & drawing in SSR Part-II, in opening, complete all as specified and directed. |
| 8 | Supply & fixing rolled mild steel angle iron chowkats including hold fasts and tie rod complete all as specified & directed. |
| 9 | Supply and fixing 35mm thick 2nd class hard wood plane framed panneled shutter (two panel) with pannels of 9mm BWP /12mm veneered particle board with commercial veneered on both faces, de tapering from 10mm to 5mm around the panel on one side fitted to chowkats. The size of rail and style as per IS 1003 (Part-1) Kiln seasoned and chemically pressure treated complete all as specified and directed. |
| 10 | Material & Labour for 35mm thick glazed and Skelton shutter of 2nd class hardwood (Hollock) open rebated and prepared to receive glass,gauge etc.divided into squares with plain chamfered or rounded mitred and rebated sash bars any number, edges of framing plain chamfered or rounded fitted with cut and mitred beads for securing glass etc. Size of members of shutters as specified in SSR Part-1 clause 8.20(a) complete all as specified and directed. |
| 11 | Dismantling wrought iron or mild steel work of any description not otherwise provided complete all as specified and directed. |
| 12 | Supply and Fix Framed work as in doors or gates of angle or other section with gusset plates, rails, braces, etc;complete,drilled for fixing of steel sheeting or other covering.Doors, etc. to be prepared for hanging or sliding with an including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering, running rails and guides) and hanging;also fastening and fixing complete all as specified and directed. |
| 13 | Supply & Fix Mild steel plain black sheet 1.00m thick but in hearths; covering to door shut ters; covering to door chowkats (frames); chullah hoods; water tanks; water troughs; ducts; urinal troughs and funnels, etc. cut to size edges beaded if directed, holes punched; including round headed screws, clout nails or rivets and fixed to wood or steel members, etc., with plain 40 mm lap joints or welded/ riveted seams including bending, turning up, mitred angles, stopped ends, outlets, etc. as required complete all as specified and directed. |
| 14 | Material & Labour Factory Made Solid PVC Moulded Door Shutter, 28 to 30mm thick (stiles), with 2 panel design with 2mm thick Moulded PVC Sheet on the front face & 2mm plain colour PVC sheet on back face, supplying & fixing in frame at site as per specification & drawing complete all as specified and directed. |
| 15 | Supply & Fix in repair Prelaminated particle board 18-19mm thick, interior grade, prelaminated one side with decorative choice lamination & other side balancing white lamination, fixed with screws to timber frame work as in selves complete all as specified and directed. |
| 16 | Supply and Fix steel window or ventilator, fixed type, with glazing bars complete all as specified and directed. |
| 17 | Supply and fixing factory made box type steel window with pintol hinges & 2 Nos 150mm mild steel tower bolt to each shutter, steel handle and with glazing bars, dovetailed or welded and with one shop coat of zinc chromate primer complete all as specified and directed. |
| 18 | Supply and fixing factory made box type steel window with pintol hinges & 2 Nos 150mm mild steel tower bolt to each shutter, steel handle and without glazing bars, including flat iron 12x3mm for securing wire mesh, dovetailed or welded and with one shop coat of zinc chromate primer complete all as specified and directed. |
| 19 | Supply and Fixing MS Framed work such as grills, gratings, etc., with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work con- forming to Fe.290.Gde-E-165, complete all as specified and directed. |
| 20 | Supply & Fixing 200 mm size Helical door spring including roller and roller plate by means of welding complete all as specified and directed |
| 21 | Supply & Fixing in repair 200 mm size Helical door spring including roller and roller plate by means of welding complete all as specified and directed |
| 22 | Supply and fixing stainless steel wire cloth, 0.36mm nominal dia of wire and average width of aperture 1.18 mm fixed to steel frames with stainless steel tacks, or stainless steel wire staples, or fixed to wooden frames with first class hard wood bead, complete all as specified and directed. |
| 23 | Supply and fixed in repair stainless steel wire cloth, 0.36mm nominal dia of wire and average width of aperture 1.40 mm fixed to steel frames with stainless steel tacks, or stainless steel wire staples, or fixed to wooden frames with first class hard wood bead, including replacement of damaged wooden bedding with and including two coat of synthetic enamel paint over a coat of pink primer complete all as specified and directed. |
| 24 | Supply and fixing plain sheet glass 4 mm thick, ordinary quality, not exceeding 0.50 Sqm in each pane, and glazing with oil putty and securing pins or with wooden beading, complete all as specified and directed. |
| 25 | Supply and fixing frosted glass 4mm thick, pin headed type, not exceeding 0.50 Sqm each pane, and glazing with oil putty and securing pins, complete all as specified and directed. |
| 26 | Hacking out old broken glass (any thickness size, quality or description) from wooden/ steel frames, glazed with putty or fixed with wooden beads/ metal pins, complete all as specified and directed. |
| 27 | Supply and fixing butt hinges, medium weight, 100mm long, cold rolled mild steel , complete all as specified and directed. |
| 28 | Supply and fixing continuous (piano) hinges mild steel, bright finish or electrogalvanised flap size 30mm, complete all as specified and directed. |
| 29 | Supply and fixing 140 mm double leaged door stopper of aluminium alloy body and tongue , anodised, with hard drawn steel spring fixed in door, complete all as specified and directed. |
| 30 | Supply and fixing in repair 140 mm double leaged door stopper of aluminium alloy body and tongue , anodised, with hard drawn steel spring fixed in door, complete all as specified and directed. |
| 31 | Supply and fix hasp & staple, safety type, aluminium anodised, 100mm size, fixed with screws, complete all as specified and directed. |
| 32 | Supply and fixing 150 mm long, extruded aluminium alloy handles, fabricated type, anodized, complete all as specified and directed. |
| 33 | Supply and fixing in repair 125 mm long, extruded aluminium alloy handles, fabricated type, anodized, complete all as specified and directed. |
| 34 | Supply and fixing, 150 mm long Aluminium, anodised, barrel tower bolts of extruded section complete all as specified |
| 35 | Supply and fixed in repairs 150 mm long Aluminium, anodised, barrel tower bolts of extruded section complete all as specified and directed. |
| 36 | Supply and fixing aluminium alloy, anodised, sliding door bolts 250 mm long, with hasp and staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy 12mm dia, complete all as specified and directed. |
| 37 | Supply and fixing in repair door bottom brush seal compring a rigid rust proof extruded aluminium carrier profile slotted with high density flexible synthetic brishels (nylon/polypropylene) to seal floor clearance gap ranging from zero mm to 25mm gap including removing existing door seal complete all as specified and as directed. |
| 38 | Material and labourfor plain cement concrete (1:3:6 ) type C-0 using 12.50 mm graded crushed / broken stone aggregate as in chowkhats filling, complete all as specified and directed. |
| 39 | Material and labour applying two coats of synthetic enamel paint over and including a coat of pink primer, on new wooden surfaces over 10cm width or girth, including preparation of wooden surface, complete all as specified and directed. |
| 40 | Material and labour, applying two coats of synthetic enamel paint over and including a coat of red oxide primer, on new steel surfaces over 10cm width or girth, including preparation of steel surface, complete all as specified and directed. |
| 41 | Supply and Fix powder coated aluminium (minmim thickness of powder coating 50 micron) work of doors, windows, ventilators and partiions (Fixed portions) with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS 733 nad IS: 1285, fixing with dash fasteners of required dia and size, including necessay fitting up the gaps at junctions, i.e. at top, bottom and sides with required EPDM runner / neoprene gasket etc, Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle. Aluminium snap beading for glazing / panelling, CP brass / stainless steel screws complete all as specified and directed. |
| 42 | Material and Labour for powder coated aluminium (minmim thickness of powder coating 50 micron) work for shutters of doors, windows, ventilators including providing and fixing hinges / pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber/neoprene gasket required (Fittings shallbe paid for separately with extruded built up standard tubular make conforming to IS 733 nad IS: 1285, fixing with dash fasteners of required dia and size, including necessay fitting up EDM runner / neoprene gasket etc, Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle. Aluminium snap beading for glazing / panelling, CP brass / stainless steel screws, complete all as specified and directed. |
| 43 | Supply and Fix Prelaminated particle board 12mm thick, interior grade, prelaminated both side decorative choice lamination & other side balancing white lamination, fixed with screws to timber frame work as in selves complete all as specified and directed. |
| 44 | Supply and Fix powder coated aluminium gril (anodised transparent or dyed to required shade acoording to IS: 1868 with minimum anodic coating of grade AC 15) of approved design /pattern, with approved standard section and fixed to the existing window frame with C.P. brass/ stainless steel screws @200 mm centre to centre, including, cutting the grill to proper opening size for fixing and operation of handles and fixing approved anodised aluminium standard section around the opening, complete all as specified and directed. |
| 45 | Supply and Fix plain sheet glass, ordinary quality 4.8mm thick in panels of aluminium doors/windows/partitions fixed with aluminium glazing clips & rubber beading complete all as specified and directed. |
| 46 | Supply and Fix Double action floor spring hydraulically regulated made up of minimum 1.25 mm thick aluminium alloy sheet foundation box, main body with stainless steel cover, governing pivot made of brass, other parts made of mild steel heavy duty complete all as specified and directed. |
| 47 | Supply and Fix in repair Door closer hydraulically regulated, designation No., universal type, aluminium body (Die Cast) suitable for door shutters of 701 to 850 mm in width and of weight between 36 to 60 kg complete all as specified and directed. |
| 48 | Supply and fix in repair MS Chromium plated curtain rod 25 mm dia with and incl MS Chromium plated decorative round funnals on either end and provide a visually balanced appearance incl MS Chromium plated brackets fixed to wall with 30mm wooden steel screws and PVC rawal plug anchors and installation complete all as specified and directed. |
| 49 | Material and Labour for Welding in repairs not exceeding 2.5cm in length (thickness of metal to be welded not exceeding 6mm) including cleaning preparing the surface and holding the members in true position for maintenance of steel items such as gates, grills, doors, windows etc., complete all as specified and as directed. |
| 50 | Demolition of brick masonry work built in cement mortar including all quoins, arches, pillars, staging etc. and removal of rubbish outside MOD land, complete all as specified and directed. |
| 51 | Material and labour for brickwork with using subclass 'B' old size bricks, straight or curved on plan exc 6 m mean radius, built in cement mortar (1:6), complete all as specified and directed. |
| 52 | Same as item No 53 above but except bricks complete all as specified and directed. |
| 53 | Taking down cement plaster on brick or stone walls or concrete surfaces, etc, any description including raking out joints, hacking for key, scrubbing down with water, etc and removal of rubbish outside MoD land, complete all as specified and directed.Note : Rate quoted by contractor shall be deemed to include to necessary scaffolding etc. |
| 54 | Material and labour for rendering 15mm thick in cement mortar (1:6), on brick/concrete surfaces of walls, finished even smooth without using extra cement , complete all as specified and directed. |
| 55 | Material and labour for rendering 15mm thick in cement mortar (1:4), on brick/concrete surfaces of walls, finished even smooth without using extra cement , complete all as specified and directed. |
| 56 | Material & Labour for rendering 10 mm thick in cement mortar (1:3), as on concrete surfaces (such as chajjas, balcony,mumty and staircase flight ceiling etc.) finished even and smooth without using extra cement, complete all as specified and directed.Note: The rate quoted by contractor is deemed to be included necessary scaffolding and form work as required upto 12.00 Mtr height building. |
| 57 | Material and labour for preparation of newly plastered surfaces of walls and applying two coats of 1st quality oil bound distemper (oil emulsion) over and including a coat of alkali resistance primer, complete all as specified and directed. |
| 58 | Material & Labour for preparing new plastered or unplastered wall surfaces, applying wall care putty to prepare the surface even & smooth & applying Two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm with over new surfaces complete all as specified and directed. |
| 59 | Material & Labour for preparation of newly plastered or un plastered ceiling surfaces of any description and applying three coats of white wash complete all as specified and directed. |
| 60 | Demolition of cement concrete ( unreinforced) in ground floors and pavings n. exe 15 cm thickness (below or above ground level ) including removal of debries out of defence land complete all as specified and directed. |
| 61 | Material and labour for 50mm thick Plain cement concrete (1:3:6), Type C-1, using 20 mm graded stone aggregate as in plinth protection, finished the surface even and fair, complete all as specified. |
| 62 | Demolition of stone slabs and tiles of any description or thickness in floors, aprons etc. laid, bedded and pointed in any mortar complete all as specified and directed. |
| 63 | Dismantling floor, hearth or wall tiling, terrazzo toping/ dado, including cement mortar bedding/backing and removing rubbish off the premises of MoD land, including preparation of dismantled surface area to receive backing coat/bedding layer for tiles, complete all as specified and directed. |
| 64 | Material and labour for first quality vitrified ceramic coloured tiles 9 to 10 mm thick, (square/rectangular) (light shade), area of each tile not exceeding 0.36 Sqm, as in floors etc, set and jointed in neat cement slurry @ 3Kg/Sqm and pointed in white cement mixed with pigment or coloured cement to match the shade of tiles, laid over and including 15mm thick screed bed in CM(1:6), complete all as specified and directed. |
| 65 | Material and labour for First quality, glazed designer pattern, jointed ceramic coloured tiles, 6-7mm thick, of size 450mm x 350mm or 450mm x 300 mm fixed in pattern as directed (combination of dark/light colour with border), on vertical surface such as in skirting, dados, risers to steps, etc., set and jointed in neat cement slurry @ 3Kg/Sqm, and including pointing in white cement mixed with pigment or coloured cement to match the shade of tiles, over and including 10 mm thick rendering in CM (1:3),complete all as specified and directed. |
| 66 | Material and labour for Non skid jointless coloured ceramic tiles 7 to 8 mm thick (square/rectangular ) area each tiles exceeding 0.11 sqm but not exceeding 0.38 sqm as in floor etc set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15 mm thick screed bed or bedding layer in C:M 1:6 complete all as specified and directed. |
| 67 | Material and labour for Machine cut Kota stone slab flooring 20-25 mm thick over cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing (granite finish) and Screed bed or bedding layer of 15 mm thick in CM 1:4 for laying floor finish complete all as specified and directed. |
| 68 | Material and labour for 20mm thick Granite (of any type) work (table rubbed and polished) as on cooking platforms, window cills, steps and like, set in neat grey cement slurry @3Kg/Sqm, laid over and including 15mm thick bedding layer in cement mortar (1:4), including pointing (if required or directed) in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite, complete all as specified and directed. |
| 69 | Material & Labour for machine cut Kota stone slab 20-25 mm thick in riser of steps, skirting, dado and pillar laid and jointed with neat cement slurry, over and including 15mm thick rendering of Cement Mortar (1:4) including pointing in white cement with pigment to match the shade of stone slabs, complete all as specified and directed. |
| 70 | Material and labour for 20mm thick Granite (of any type) work, machine cut, as skirting/dado laid over cement screed and jointed in neat grey cement slurry, laid over and including 15 mm thick bedding layer in cement mortar (1:4), including pointing (if required or directed) in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite, including cutting and moulding the corners/edges, grinding & polishing, complete all as specified and directed. |
| 71 | Material and labour for 25 mm thick plain cement concrete (1:2:4) type B-0 using 12.5 mm graded crushed stone aggregates as in floor, finished the surface even & rough to receive the bedding mortar, complete all as specified and directed. |
| 72 | Dismantling brick tiles or terracing tiles, single layer on roof including segregating and stacking serviceable brick tiles and removal of unserviceable brick tiles / brick bats and rubbish outside defence land, complete all as specified and directed. |
| 73 | Taking down existing water proofing treatment and chiesling the existing bituminouns coating and rubbish off the premises to a distance exeeding 150 metre and not exceeding 250 metre complete all as specified and directed. |
| 74 | Demolition of mud phuska on roofs, any thickness, including plaster and leeping plaster and bottom layer of polythene film if any, including removal of retrieved material outside defence land, complete all as specified directed. |
| 75 | Material & labour plain cement concrete (1:2:4) type B-1, using 20 mm graded mechanically crushed stone aggregates as in,roof kerb ,padding to roof to maintain the required slope and finished the surface even and smooth, without using extra cement, complete all as specified and directed. |
| 76 | Supply only integral water proofing compound, complete all as specified and directed. |
| 77 | Providing and applying fibre reinforced elastomeric liquid water proofing membrane with resilient acrylic polymers having Sun Reflectivity Index (SRI) of 105 on top of concrete roof in three coats @10.76 litre/ 10 sqm. One coat of self-priming of elastomeric waterproofing liquid (dilution with water in the ratio of 3:1) and two coats of undiluted elastomeric waterproofing liquid (dry film thickness of complete application/system not less than 500 microns). The operation shall be carried out after scrapping and properly cleaning the surface to remove loose particles with wire brushes, complete in all respect as per the direction of Engineer-in-Charge.. The work will cariied out on on horizontal and vertical surface. 10 years Waterproofing warranty on Terraces and work will be carried out by Authorized Applicator only complete all as specified and directed.Make: Berger, Nerolac, Asian, Dulux. |
| 78 | Supply and fixing in 110 mm dia bore PVC (SWR) pipes, double socketed, in any length, with rubber ring joints, fixed to wall, complete all as specified and directed. |
| 79 | Supply and fixing in 110mm bore PVC (SWR) bends any radius, fixed to pipes with adhesive, complete all as specified and directed. |
| 80 | Taking down eaves gutters and rainwater pipes (any size or pattern), including all fittings, heads, shoes, bends, swan-necks, etc., including cleaning or refixing or removal to Store (measured overall as fixed along the centre line over fittings and accessories. |
| 81 | Supply and fixing in repair for Providing and repairing existing mineral fibre false ceiling, including removal of damaged tiles, replacement of damaged GI intermediate cross tees and suspension clips, re-alignment and levelling of existing grid and providing 600X600X16 mm RH-99 fine-fissured mineral fibre tiles, including scaffolding, staging and disposal of debris, complete all as specified and directed. |
| 82 | Taking up or down existing steel water tubing and connections, 15mm bore for re-fixing or removing from site to store for reuse or credit, including taking down standard fittings, complete all as specified and directed. |
| 83 | Taking up or down existing steel water tubing and connections, 20 mm bore for re-fixing or removing from site to store for reuse or credit, including taking down standard fittings, complete all as specified and directed. |
| 84 | Supply and fixing galvanized steel water tubes 15mm bore, medium grade, with all standard fittings such as bends, elbows, tees etc, concealed/on surface, fixed to walls and ceiling or laid in floors, complete all as specified and directed. Note : Cutting chases as required shall be measured and paid separately. |
| 85 | Fixing only, old steel water tubing, 15mm bore pipe, with all fitings in new or old position (walls, ceiling, floors etc), complete all as specified and directed.Note : Old steel tubing shall be fixed after proper checking, cleaning washing, bleaching etc. |
| 86 | Supply and fixing galvanized steel water tubes, 20 mm bore, medium grade, with all standard fittings such as bends, elbows, tees etc, concealed/on surface, fixed to walls and ceiling or laid in floors, complete all as specified and directed. Note : Cutting chases as required shall be measured and paid separately. |
| 87 | Fixing only, old steel water tubing, 20 mm bore pipe, with all fitings in new or old position (walls, ceiling, floors etc), complete all as specified and directed.Note : Old steel tubing shall be fixed after proper checking, cleaning washing, bleaching etc. |
| 88 | Supply & Fix in repair PVC 110 mm bore soil waste or vent pipe as in any length with or without ears with cement joints laid in floor in complete all as specified and directed. |
| 89 | Supply & Fix in repair PVC 75 mm bore soil waste or vent pipe as in any length with or without ears with cement joints fixed to walls in complete all as specified and directed. |
| 90 | Supply & Fix in repair PVC 75 mm bore soil waste or vent pipe as in any length with or without ears with cement joints laid in floor complete all as specified and directed. |
| 91 | Supply and fixing in repairs 75 mm cast iron floor trap,ISI marked, with mild steel CP grating including jointing to waste pipe, and set in cement concrete 1:2:4 as required, complete all as specified and directed. |
| 92 | Supply and fixing in repairs PVC connections of PTMT, non corrosive, with nuts & washers on both ends, 450 mm long suitable for 15mm dia bore pipe, complete all as specified and directed. |
| 93 | Supply and fixing Vitreous china wash hand basin, white, flat back, size 550mm x 400mm, including brackets and cutting for and pinning in ends of brackets, complete including CP brass waste coupling, PVC waste pipe, brackets & including taking down old and removal of old from site, complete all as specified. |
| 94 | Supply and fixing in repairs vitreous china wash down water closet (pedestal pattern) white pedestal pan and trap, including connection to drain ( or out going pipe ) and to flushing pipe, anti syphonage pipe, with plastic water closet seat cover white, closed pattern with flat bottom and mild steel chromium plated or aluminised hinging device etc complete all as specified and directed. |
| 95 | Supply and fixing urinal spreader of PTMT any colour for fixing with 15mm dia pipe (minimum weight 60 gms), complete all as specified and as directed. |
| 96 | Suppply and Fix in repair Vitreous China urinals, half stall type (back or corner wall type), complete including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and including 60mm long brass screws, pointing around urinal back in cement, flush pipe, grating and Union for discharge pipe complete all as specified and directed. |
| 97 | Supply and fixing vitreous china wash down water closet squatt pan, Indian type (Orissa pattern), of size 550mmx400mm, white with integral foot rests (excluding flushing cistern and flushing pipe but including CI ‘P’/’S’ trap), set in & jointed with appropriate adhesive/mortar including embedding in concrete and taking down old and removal of debris outside MOD land, complete all as specified and directed. |
| 98 | Supply and fixing 10 litre capacity virgin polypropylene (PVC) low level flushing cistern, ISI marked, white or coloured, valve less symphonic action type, with inlet, ball valve, float and handle, complete including PVC bend/ flush pipe, brackets and making all connections, fixed as in repairs and removal of old from site to store for reuse or credit, complete all as specified and directed. |
| 99 | Supply and Fix in repair 15mm bore bib taps brass cast copper alloy (CP) with crutch or butterfly handles, screwed down, screwed for iron pipes or for brass ferrules and fixed complete all as specified and directed. |
| 100 | Supply and Fix only pillar tap cast copper alloy CP 15 mm with Swan Neck ,screwed down high pressure for iron pipe fixed in repairs complete all as specified and as directed. |
| 101 | Supply and fixing in repairs angle/stop valve, cast copper alloy, with crutch or butterfly handle, chromium plated, screwed down high pressure, screwed for iron pipe or for brass ferrule 15mm bore dia, including removal of old to store for reuse or for credit, complete all as specified and directed. |
| 102 | Supply and Fix in repair 600mmx450mm bevelled edge mirror of selected quality glass, mounted on 5mm thick PVC and fixed to wooden plugs with chromium plated brass screws and cup washers complete all as specified and directed. |
| 103 | Supply and Fix in repair CP grating of size 100mm dia complete all as specified and directed. |
| 104 | Material and Labour in repair 32mm waste fittings, brass, chromium plated for glazed ware sinks, basins, etc. With long screwed shanks and flu-nuts, flange end bedded in red lead cement and other end complete all as specified and directed. |
| 105 | Supply and fix in repair Pillar taps 15 mm dia of PTMT any colour high pressure screwed for iron pipe and fixed (Minimum weight 15mm-110gms) complete all as specified and directed. |
| 106 | Supply and fixing in repairs bib taps PTMT,15 mm bore , any colour, (weight not less than 90 grams), ISI marked, high pressure, complete all as specified and directed. |
| 107 | Supply and fixing in repairs stop valve PTMT,15 mm bore , any colour, (weight not less than 90 grams), ISI marked, high pressure, complete all as specified and directed. |
| 108 | Dismantling existing water tanks of size exc 250 Litre but n.exc 500 litre capacity and removal from site to store for reuse or credit, complete all as specified and directed. |
| 109 | Dismantling existing water tanks of size exc 500 Litre but n.exc 1000 litre capacity and removal from site to store for reuse or credit, complete all as specified and directed. |
| 110 | Supply and Fix Rotational moulded PVC, double layered, water storage tanks of capacity 500 litre (cylindrical vertical with closed top), ISI Marked, hoisted and fixed in position, with & including all fittings such as GI tank nipple etc. but excluding ball valve , complete all as specified and directed. |
| 111 | Supply and Fix Rotational moulded PVC, double layered, water storage tanks of capacity 1000 litre (cylindrical vertical with closed top), ISI Marked, hoisted and fixed in position, with & including all fittings such as GI tank nipple etc. but excluding ball valve , complete all as specified and directed. |
| 112 | Fixing only old retrieved , water storage tanks of capacity 500 litre (cylindrical vertical with closed top), ISI Marked, hoisted and fixed in position, with & including all fittings such as GI tank nipple etc. but excluding ball valve , complete all as specified and directed. Please Enable Macros to View BoQ information |
| 113 | Fixing only old retrieved , water storage tanks of capacity 500 litre (cylindrical vertical with closed top), ISI Marked, hoisted and fixed in position, with & including all fittings such as GI tank nipple etc. but excluding ball valve , complete all as specified and directed. Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Sep 29, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedOct 13, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 10 daysOct 20, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 17 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender