Tender For Renovation Of Existing Swimming Pool At Hcm Ripa C Us, Jaipur
Tender Value
1.91 Crore
Estimated cost
Bid Submission
07 Oct 2026
7 days left
EMD
3.82 Lakhs
Bank guarantee accepted
Document Fee
2360
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Jaipur → Rajasthan
EMD Exemption
Not Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for Renovation Of Existing Swimming Pool At Hcm Ripa C Us, Jaipur
BOQ
| Sl. No. | Item Description |
| 1 | Dismantling tile work in floors and roofs laid in cement mortar including stacking of serviceable material and disposal of unserviceable material within 50 meter lead: For thickness of tiles 10mm to 25mm. |
| 2 | Dismantling stone slab/ terrazo chip flooring laid in cement mortar including stacking of serviceable material and disposal of unserviceable material within 50 meters lead. |
| 3 | Dismantling old plaster or skirting, raking out joints and cleaning the surface for plaster including disposal of rubbish to the dumping ground within 50 meter lead. |
| 4 | Demolishing brick work manually/ by mechanical means including stacking of serviceable material and disposal of unserviceable material within 50 metres lead as per direction of Engineer-in-charge. n cement mortar |
| 5 | Demolishing cement concrete manually/ by mechanical means including disposal of material within 50 metres lead as per direction of Engineer-in-charge. 1: 3: 6 or richer mix. |
| 6 | Dismantling steel work in single sections including dismembering and stacking within 50 meters lead in:Channels, angles, tees & flats. |
| 7 | Labour charges for removing W.C. pan (any type) of all sizes with care including all necessary fittings P or S trap. |
| 8 | Earth work in excavation by mechanical means (Hydraulic Excavator )/ manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan) including dressing of sides and ramming of bottoms, lift upto 1.5 m, including taking out the excavated soil and depositing and refilling of jhiri with watering & ramming and disposal of surplus excavated soil as directed with in a lead of 50 meter. All kinds of soils |
| 9 | Clearing jungle including uprooting of rank vegetation, grass, brush wood, trees and saplings of girth upto 30 cm measured at a height of 1 m above ground level and removal of rubbish upto a distance of 50 m outside the periphery of the area cleared. |
| 10 | Excavating trenches of required width for pipe, cables etc. including excavation for sockets and dressing of sides, ramming of bottoms, depth up to 1.5 Mtr. including taking out the excavated soil and then returning the soil as required in layers not exceeding 20cm in depth including consolidating each deposited layer by ramming, watering etc. and disposal of surplus excavated soil as directed within a lead of 50 Mtr.:All kinds of soilPipes, cables etc. exceeding 300mm dia but not exceeding 600mm dia. |
| 11 | Making of hole in R.C.C. slab/wall/beams and masonary wall (width up to 450 mm) by core cutting machine complete as per direction of EI From diameter 100mm to 150mm (B-13/13.34.1) |
| 12 | Providing and laying in position cement concrete including curing, compaction etc. complete in specified grade excluding the cost of centering and shuttering - All work up to plinth level. M15 grade Nominal Mix M10 grade Nominal Mix 1: 3: 6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20mm nominal size). |
| 13 | Providing and laying in position cement concrete including curing, compaction etc. complete in specified grade excluding the cost of centering and shuttering - All work up to plinth level.M20 grade Nomina1: 1.5: 3 (1 cement : 1.5 coarse sand : 3 graded stone aggregate 20mm nominal size). |
| 14 | Providing and fabricating reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding (including cost of binding wire) all complete up to floor five level. Thermo-mechanically Treated bars (Conforming of relevent IS cod |
| 15 | Centering & shuttering with plywood or steel sheets including strutting, propping bracing both ways with steel props and removal of formwork for upto floor five level for :Suspended floors, roofs, landings, staircases, balconies, girders, cantilevers, bands, coping bed plates, anchor blocks, sills, chhajjas, lintel, beam, plinth beam etc. |
| 16 | Providing and fixing Granite stone slab mirror polished and machine edge cut in walls, pillars, steps, Shelves, Sills Counters, Floors etc. laid on 12mm (Av.) thick base of cement mortar 1:3 (1 cement : 3 coarse sand) jointing with white cement mortar 1:2 (1white cement : 2 marble dust) with pigment to match the shade of the marble slab including grinding, rubbing and polishing complete.Above 3601 Cm2 Slabs, 15-18mm thick South zed black |
| 17 | Extra for providing edge moulding to 15-19 mm thick marble/Granite stone counters, Vanities etc. including machine polishing to edge to give high gloss finish etc. complete as per design approved by Engineer-in-charge. Granite work Full Edge moulding |
| 18 | Rough Chisel dressed Kota stone 35 mm thick flooring of approved shade set in pattern over 20mm thick base of cement mortar 1:6 (1 cement : 6 coarse sand) and pointing with cement sand mortar 1:3 with pigment to match the shade of stone with joint thickness up to 15 mm complete in all respects : |
| 19 | Half Brick work with mechanised autoclaved flyash lime bricks conforming to IS: 12894 :2002 of class designation 100 in superstructure above plinth level upto floor V level in. Cement mortar 1 : 4 (1 cement : 4 coarse sand) |
| 20 | Brick work with clay flyash F.P.S. brick (IS 13757- 1993 ) of class designation 75 in superstructure above plinth level upto floor five level in : Cement mortar 1 : 4 (1 cement : 4 coarse sand) |
| 21 | Plaster on new surface on walls in cement sand mortar 1:4 including racking of joints etc. complete fine finish :20mm thick |
| 22 | Supplying and fixing in walls machine cut and polished stone shelves, tands and in CM 1:3 with machine cut edges Sand or other approved stone 50mm thick. |
| 23 | Providing and fixing Marble stone flooring table rubbed, 15-18 mm thick over 20mm (Av.) thick base of CM 1:4 (1 cement : 4 coarse sand) jointing with white cement mortar 1:2 (1 white cement : 2 marble dust) with pigment to match the shade of the marble slab including grinding, rubbing and polishing complete.Makrana 'Adanga'.Above 3601 Cm2 Slabs |
| 24 | Extra for providing edge moulding to 15-18mm thick marble/ Granite/Kota stone counters, Vanities etc. including machine polishing to edge to give high gloss finish etc. complete as per design approved by Engineer-in-ChargeMarble work. Full Edge moulding |
| 25 | Extra for providing opening of required size & shape for wash basins/Kitchen sink in Kitchen platform, vanity counters and similar location in Marble/ranite/stone work including necessary holes for Pillar taps etc. including rubbing and polishing of cut edges etc. complete. |
| 26 | Fine dressed & machine cut edges 30-35 mm thicksand stone flooring over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) jointed grey cement slurry mixed with pigment to match the shade of stone complete as per design drawing and instruction of EI.Pink sand stone (Bansi Paharpur stone |
| 27 | Providing and fixing aluminum work for doors ,windows, ventilators and partition with extruded built up standard tubular / appropriate Z sections and other sections of approved make conforming to IS :733 and IS :1285, fixed with rawl plugs and screws or with fixing clips ,or with expansion hold fasteners including necessary filling up of gap. at junctions , at top ,bottom and sides with required PVC/neoprene felt etc. Aluminium section shall be smooth ,rust free, straight ,mitered and jointed mechanically wherever required including cleat angle Aluminium snap beading for glazing /paneling , C.P. brass/ stainless steel screws Al. Tower bolt & Al. handle & Al. Aldrop etc.,all complete as per architectural drawings and the directions of Engineer- in – charge .(Glazing and paneling to be paid for separately).For shutters builtup standard tubular sections of openable doors ,windows & ventilators including providing & fixing hinges / rollers etc. and making provision for fixing of fittings wherever required (lockes shall be paid for separately).Polyester Powder coating aluminum ( minimum thickness ofpowder coating 50 micron) |
| 28 | Providing and fixing glazing in aluminium door, window ,ventilator shutters and partitions etc. with PVS / neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-in-charge.(Cost of aluminium snap beading shall be paid in basic item.)With float glass panes of 5.0 mm thickness ( weight not less than 13.50 kg/sqm) |
| 29 | Providing & fixing factory made 100% Solid WPC (Wood Polymer Composite) Door Frame 90mm x 45 mm ( Moulded ) Single Rebated,, made from Wood Polymer Composite (Single Extruded Process) material comparising of virign PVC polymer of K Value 58-60 ( Suspemsion Grade), Calcium Corbonate and Natural Fibers ( Wood Powder/ Rice Husk/ Wheat Husk) and Nor toxic additives fabricated with meter Joints after applying PVC solvent Cement & screwed with full body treaded star headed srews having minimum frame density of 780 kg/ cbm & manufactured by an ISO 9001 - 2015 Certified Company, having good screw holding capacity ( Screw Withrawal strength of 2200 N ( Face) & 1100 N ( Edge), Minimum Compissive Stength of 58 N/mm2, Moduus of elasticity 900N/mm2 and resistance to spread of flame of class A category with property of being termite / borer proof , water / Moisture Proof & Fire retardant & Fixed in postion with SS Dash Fasterns / Hold Fast of reuired dia and lenght, all as per specifications drawings as directed by the Engineer-In-Charge. Material test certificate and authentication should be compulsory provided by the manufacturing company ( Hold Fast or Dash Fastners shall be paid seperately) |
| 30 | Providing and fixing of uPVC Sliding windows: Frame Made from the Extruded uPVC Window Profile Section of size as mentioned below having outer wall thickness of 2.5mm (+/- 0.2mm) and 3 box multi-chamber construction, White in finish, duly reinforced with 1.2 mm thick GI section. Frame shall have three track configuration, two for sliding of window shutter and one for mosquito mesh shutter. Vertical member of frame which bears the sliding shutter load shall have aluminium rail/track for smooth sliding of shutter rollers. All the four corners shall be mitered cut & thermal welded so as to form window frame. Frame shall be milled with drain and air equalizer hole in order to be water tight and for drainage of accumulated water, if any, to outer side.Shutter : The shutter of sliding window shall be made of size as mentioned below Extruded 3 box multi- chamber uPVC Window Profile Section of white colour having outer wall thickness of 2.5mm (+/- 0.2mm) provided with reinforcement of 1.5mm thick GI section duly mitered cut & thermal welded at all corners and fitted with uPVC glazing bead of size 22 x 20 mm with inner and outer co-extruded EPDM/TPE-E weather seal gaskets alongwith 6mm thick ISI make plain float glass. Mesh shutter shall be made of 39w x 69h mm Extruded 3 box multi-chamber UPVC Window profile section of white colour having outer wall thickness of 2.5mm (+/- 0.2mm) provided with reinforcement of 1.5 mm thick GI section duly mitered cut & thermal welded at all corners and fitted with nylon/polymer mesh and rollers/pully.Window profile section of size 106 w x 50 h & shutter of sliding window shall be made of 39 w x 69 h |
| 31 | Providing and fixing steel gate, grating , and grills made of angles, tees, square bars, flats,or black pipe with holdfast and fittings complete as per design and drawing including cutting welding and fabrication with priming coat of red oxide |
| 32 | Extra if square,rectangular hollow tubelar sections are used or grill made by flats only |
| 33 | Providing and Fixing Aluminium composite panel of approved make 3mm thick with 0.5mm thick skin & PVDF coated approved shade for wall panelling. Main framing work to be done using 50mmx25mmx1.6mm tubular section of approved make. Stainless steel screw to be used to fix the ACP panel to be fixed to the main frame with industrial adhesive tape and panel groove to be sealed with weather proof silicon sealant suitable for glass/aluminium etc. complete in all respect as approved by Engineer-in-charge. |
| 34 | Filling the gap upto 5 mm depth and 5 mm width in between aluminium frame & adjacent RCC/ Brick/ Stone work by providing weather silicon sealant over backer rod of approved quality as per architectural drawings and direction of Engineer-in-charge complete. |
| 35 | Providing and fixing double action hydraulic floor spring of approved brand and manufacture IS : 6315 marked, for doors including cost of cutting floors as required, embedding in floors and cover plates with brass pivot and single piece M.S. With stainless steel cover plate |
| 36 | Providing and fixing 100mm brass locks (best make of approved quality) for aluminium doors including necessary cutting and making good etc. complete. |
| 37 | Providing and fixing aluminium U shape handle of size 100mm with SS screws etc. Complete as per direction of Engineer-in-charge Powder coated minimum thickness 50 micron aluminium |
| 38 | CARRIAGE OF MATERIALS.Building Rubbish Stone metal (Grit and ballast etc.)For 20 Km |
| 39 | Providing Factory Made 100% Solid WPC (Wood polymer Composite) Board of 18mm thicknesss of required size comprising of virign PVC resin of K Value 58-60 ( Suspemsion Grade), Calcium Corbonate and natural Fibers ( Wood Powders/ rice husk/ wheat husk) and Non toxic additives , made from Extrusion process WPC foam sheet Single Extruded ( Inner) with density not less than 550 kg/cbm manufactured by an ISO 9001 - 2015 Certified Company, having good screw holding capacity ( Screw Withrawal strength of 1800 N ( Face) & 900 N ( Edge), Minimum Compissive Stength of 58 N/mm2, Modulus of elasticity 900N/mm2 and resistance of spread of flam of Class A caegory wih Property of being Termite/ Borer Free.Water/ Moisture Proof and Fire Retardant and fixinng stainless Steel butt hinges of required size with necessary full body threaded star headed counter sunk SS Screws. All as per direction of Engineer -In-Charge, Material test certificate and authentication should be compulsory provided by the manufacturing company : For KITCHEN CABINET & CUPBOARDS.. |
| 40 | Providing & Fixing BWR ISI marked 19 mm board of approved make for making wardrobe/shelves and other furniture with fevicol & nails complete as per approved by engineer in charge. |
| 41 | Repair of door, window shutters including cost of material and labour for change of damaged : |
| 42 | Aldrop of mild Steel12\\" long x12mm dia |
| 43 | Stopper of Aluminium withDouble Rubber Gutka |
| 44 | Door Springs of mild Steel |
| 45 | Steel HingesFor Wooden Chowkhat 4\\" size |
| 46 | Mild Steel Tower Bolt 6\\" long |
| 47 | Steel Locking Bolt |
| 48 | Steel Handle 6\\" size |
| 49 | Providing & Fixing of ward robe shutters made out of 19mm thick BWP block board ISI of superior quality make with following details :-Front side finishing with 1mm thick superior quality mica approved make and 0.8mm thick approved shade mica in the inner side. Covering with teak wood beading 25x12mm all the sides of shutter & 35x12mm on outer frame for making good the wall joint including heavy brass S.S. fittings (Handle 200mm 2 Nos., Tower Bolt 150mm 2 Nos., Brass Lock 1 Nos., Magnetic Catcher 2 Nos., Brass Hinges 75x40x2.5 mm 6 Nos., SS Hanger Rod 20mm dia) complete as per drawing and design approved by Engineer in Charge |
| 50 | Providing and fixing IS : 3564 marked aluminium extruded section body tubular type universal hydraulic door closer with double speed adjustment with necessary accessories and screws etc. complete. |
| 51 | Providing and fixing wood panelling or panelling and glazing in panelled or panelled and glazed shutters for doors, windows and clerestory windows (Area of opening for panel inserts excluding portion inside grooves or rebates to be measured). Panelling for panelled and glazed shutter 25 mm to 40 mm thick12 mm thick glass |
| 52 | Extra for providing frosted glass panes instead of ordinary float glass panes in doors, windows and clerestory window shutters. (Area of opening for glass panes excluding portion inside rebate shall be measured). |
| 53 | Extra for providing toughened glass panes instead of ordinary float glass panes in doors, windows and clerestory window shutters. (Area of opening for glass panes excluding portion inside rebate shall be measured). |
| 54 | Providing and laying water proofing treatment to vertical and horizontal surfaces of depressed portions of W.C., kitchen and the like consisting of : i) Ist course of applying cement slurry @ 4.4 Kg/sum mixed with water proofing compound conforming to IS 2645 in recommended proportions including rounding off junction of vertical and horizontal surface.ii) IInd course of 20mm cement plaster 1:3 (1 cement: 3 coarse sand) mixed with water. proofing compound in recommended proportion including rounding off junction of vertical and horizontal surface..iii) IIIrd course of applying blown or residual bitumen applied hot at 1.7 Kg per sqm. of area.iv) IVth course of 400 micron thick PVC sheet .(Overlaps at joints of PVC sheet should be 100 mm wide and pasted to each other with bitumen @ 1.7 Kg/sqm.) |
| 55 | Providing gola 75x75 mm in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 stone aggregate 10mm and down gauge) including finishing with cement mortar 1:3 (1 cement : 3 fine sand) as per standard design : |
| 56 | Finishing with neat cement (punning). |
| 57 | Providing & applying Three coat of pure Acrylic Water based elastomeric brush applied insulating coating on exterior surface overwaterproofing slurry coat , initial coat of 50-75 micron thickness with diluting 1 part of chemical with 2 parts of clean water, over which applying 2 coats at 2 Hrs, intervals each with diluting 1 part of chemical with 10% of clean water for total thickness of 400 to 450 microns (covering area 0.9 Sq.M/Kg of chemical) including preparation of surface by cleaning, brushing and dust removing, scaffolding if necessary etc., with contractor's labour, tools, machinery etc, complete as directed by Engineer in Charge. |
| 58 | Stone work (machine cut edges) for Wall cladding/ Veneering work up to 10 m height with 20 to 30 mm thick Pink Sand stone (Bansi Paharpur) and backing filled with a grout of 12mm thick cement mortar 1:3 (1 cement : 3 coarse sand) including pointing in white cement mortar 1:2 (1 white cement : 2 stone dust) with an admixture of pigment matching the stone shade : (To be secured to the backing by means of cramps which shall be paid separately)Exposed face Machine cut |
| 59 | Providing and fixing stainless steel cramps of required size and shape for anchoring stone wall lining to the backing or securing adjacent stones in stone wall lining in cement mortar 1:2 (1 cement : 2 coarse sand) including making the necessary chases in stone and holes in walls wherever required |
| 60 | Providing and fixing expandable fastners of specified size with necessary plastic sleeves and galvanised M.S. screws including drilling holes in masonry work /CC/R.C.C. and making good etc. complete50 mm long |
| 61 | Removing white or colour wash by scrapping and sand papering and preparing the surface smooth including necessary repairs to scratches by sandla/loi. (only for colour changing ). |
| 62 | Applying one coat of Cement primer of approved brand and manufacture on wall surface including all scaffolding: |
| 63 | Providing and applying white cement based putty over plastered surface to prepare the surface even and smooth complete New Plastered Surface (three or morecoats) |
| 64 | Wall painting with plastic emulsion paint of approved brand and manufacture to give an even shade including all scaffolding: two or more coats on new work including prepartion of base with primer, putty, lippy etc complete in all respec |
| 65 | Painting with synthetic enamel paint of approved brand and manufacture to give an even shade Two or more coats on new work : |
| 66 | Painting exterior surface of Wall with 100% acrylic exterior paint of approved brand and manufacture to give an even shade with two or more coats including prepartion of base with sand papering, primer, putty, etc complete in all respect including scaffolding and safety provision new Work |
| 67 | Spray painting in approved shade and approved quality with Duco paint of required colour to give even shade with two or more coats by compressor including sand papering, NC putty filler coat etc complete in all respect as per design given by Engineeer incharge on new work. |
| 68 | Face lifting (Doba Wash) with washing of stones by (1:20) acid & water solution, rubbing by brush, washing by clear water, pointing of damaged grooves & doba washing with good quality lime water and painting of doors, windows, ventilators upto all height & lead including all scaffolding and T&P etc. complete as per instructions and direction of Engineer-in-charge. |
| 69 | Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge. (Concealed work including cutting chases and making good the walls etc., 20mm nominal outer dia pipes |
| 70 | Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge. (Concealed work including cutting chases and making good the walls etc.,)25 mm nominal outer dia pipes |
| 71 | Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings, this included jointing of pipes & fittings with one step CPVC solvent cement , trenching refilling & testing of joints complete as per direction of Engineer in Charge.(External work).32mm nominal outer dia pipes |
| 72 | Supply & fixing G.I. Union ISI marked in G.I. pipe line as required complete in all respect of size : |
| 73 | 25mm dia nominal bore |
| 74 | 32mm dia nominal bore |
| 75 | 40mm dia nominal bore |
| 76 | 50mm dia nominal bore |
| 77 | P & F G.I. Pipes (External Work) with G.I. fittings excluding union (IS : 1239 Mark) including trenching & refilling earth etc. |
| 78 | 25mm dia nominal bore |
| 79 | 'B' Class |
| 80 | 32mm dia nominal bore |
| 81 | 'B' Class |
| 82 | 40mm dia nominal bore |
| 83 | 'B' Class |
| 84 | 50mm dia nominal bore |
| 85 | 'B' Class |
| 86 | P & F Full-way Valve (IS:778 Mark) or wheel valve of approved make : |
| 87 | (-do-) 25mm nominal bore. |
| 88 | (-do-) 32mm nominal bore. |
| 89 | (-do-) 40mm nominal bore. |
| 90 | (-do-) 50mm nominal bore. |
| 91 | Making connection of G.I. distribution branch with G.I. main including all fitting. Upto 25mm dia (S-2/2.3.1) |
| 92 | Filling of sunk portion of roof with earthen pots of required height including filling voids with 1:3:6 light concrete, using brick bats complete levelling and dressing the surface by 50mm thick cement concrete 1:2:4 as per specification. |
| 93 | Construction of Cement Concrete Chamber 125mm dia on depressed floor upto 45cm height from floor with C.P. Brass grating (S-3/3.39.1) |
| 94 | Providing and fixing 1st quality MAT finished ceremic tile size 300x300mm confirming to IS : 13755 and IS : 15622 colour such as white, grey, ivory, fume red brown, light green, light blue and other light shades in floors, steps, pillars etc. laid on a bed of neat cement slurry finished with flush pointing in the white cement mixed with pigment to match the shade of the tile complete (including the cost of cement mortar bed 1:4). |
| 95 | Supply of Hydraulic Seat Cover for Europeon WC of superior quality approved make in white Colour |
| 96 | Providing & Fixing chair for wall hung W.C. |
| 97 | Providing & Fixing Premium Quality white glazed vitreous china Sanitary Wares (IS:2556 Mark) of approved make as per direction of Engineer-in-charge including cutting and making good the wall and floorWall Mounting European type W.C. |
| 98 | Providing & Fixing Concealed cistern with Floor mounting frame and flush plate of superior quality and approved sample by Engineer-in-charge. |
| 99 | P & F Indian type white glazed vitreous china 1st quality W.C. orissa pan (IS :2556 Mark) with 100 mm vitreous china P or S trap including cutting and making good the wall and floor: Size 580x440mm. |
| 100 | P & F Low level Flushing Cistern of 10 litres capacity (IS : 2556mark). Of approved make with complete fittings C.I. brackets duly painted, brass ball cock with ball, (IS: 1703 mark) complete including cutting and making good the wall:PVC with PVC bend as per IS : 7231 . |
| 101 | Providing and fixing Superior quality CP Brass fittings of approved make as per direction of Engineer-in-charge |
| 102 | Bib Cock with long thread 15 mm nominal size |
| 103 | Long body Bib Cock 15 mm nominal size |
| 104 | Two way Bib Cock 15 mm nominal size |
| 105 | Single lever wash basin mixer with 450 mm long copper connection pipe |
| 106 | 600 mm long towel rail |
| 107 | Revolving type towel ring |
| 108 | Soap dish |
| 109 | 190 mm rain shower |
| 110 | Shower arm |
| 111 | Paper holder |
| 112 | Soap Dispenser |
| 113 | Health focet (Superior Quality) |
| 114 | Double coat hook |
| 115 | Jet Spray |
| 116 | Providing and fixing Premium quality Towel rack 600mm long 260mm wide with lower hangers CP Brass fittings of approved make as per direction of Engineer-in-charge |
| 117 | P & F WVC Wash basin (Ist quality IS:2556 Mark) of approved make with C.I. brackets duly painted 1 No. 15 mm C.P. Pillar cock (IS:8934 Mark) & 32 mm C.P. brass waste coupling of approved make, P.V.C Waste pipe with PVC nut 32 mm complete including cutting & making good the wall :Size 610 mm x 510 mm |
| 118 | P & F Bevelled edge Mirror/mirror with teak wood lipping around of special glass of approved make as per direction of Engineer-in-charge complete with 6mm thick commercial ply base fixed to wooden screws & washers. Other sizes |
| 119 | Providing & Fixing Premium quality Bottle trap internal portion 32mm, size 250mm long wall connection pipe & wall flange as per approved by Engineer in Charge. |
| 120 | Providing and fixing premium quality Angular stop cock 15mm with wall flange complete as per sample approved by Engineer in charge |
| 121 | P & F Divertors in water supply lines for walls, wash basin etc. |
| 122 | Providing & fixing C.P.flange for 15mm dia taps. |
| 123 | P & F Extension Pipe for bib cocks of approved quality/make. C.P. brass of Heavy & Superior quality 100x15mm |
| 124 | P & F PVC Storage Tank ISI Marked (IS : 12701) indicating the BIS license No), of approved make with cover, 25mm dia 1M long G.I. over-flow pipe & 25 Cm. long wash out pipe with plug & socket, including making connection etc., complete of approved design 500 litres capacity. |
| 125 | Hoisting Charges for each floor :For items 2.26.1 to 2.26.4 |
| 126 | P & F Ball Cock (IS :1703 Mark) with Rod & P.V.C. Ball complete :Brass wt. Not less than 600 gm,25mm. |
| 127 | P&F rigid PVC Pipe (IS:4985 mark) class II/ (4 Kg. /Cm2.) approved quality /make including joining the pipe with solvent cement rubber ring and lubricant.110 mm dia |
| 128 | P&F rigid PVC pipe fittings (IS: 4985 mark) of approved quality /make including joining the pipe with solvent cement rubber ring and lubricant:Door Tee110mm dia |
| 129 | P&F rigid PVC pipe fittings (IS: 4985 mark) of approved quality /make including joining the pipe with solvent cement rubber ring and lubricant: |
| 130 | Pipe Clip110mm dia |
| 131 | Providing and Fixing Unplasticized Poly Vinyl Chloride (UPVC) SWR Pipes Type B for sciland waste discharge system (IS:13592 : 1992 Marked) of approved quality /make110 mm dia |
| 132 | Providing and Fixing Unplasticized Poly Vinyl Chloride (UPVC) SWR Pipes fittings type B for sciland waste discharge system (IS:13592 : 1992 Marked) of approved quality /make |
| 133 | Coupler110mm dia |
| 134 | Bend 45 Dg.110mm dia |
| 135 | Door Bend 87.5 Dg.110mm dia |
| 136 | W.C. Connector110mm dia |
| 137 | Offset110mm dia |
| 138 | Vent Cowel 110mm dia |
| 139 | Nahni Trap with Jali 4”110mm dia |
| 140 | P & F Square-mouth gully trap `A` grade (IS :marked) of approved make complete with C.I. grating, frame & Cover masonry chamber in C.M. 1:6, 100mm thick C.C. 1:5:10 base concrete, 40mm thick C.C.M-15 grade coping, 12mm thick cement plaster in CM 1:3 complete as per approved design & type. Trap size 225 X 150 mm, ferrow cement cover with frame Internal Chamber size 450 X 450mm. |
| 141 | Labour charges for making connection of sewer line through main hole. |
| 142 | Construction of manhole in all type of soil inner size 90 X 60 Cm. 450 mm thick masonry in CM 1:6, 10 Cm. thick cement concrete 1:5 10 in foundation, 20 mm thick inside plaster in CM 1:6, finished with floating neat cement, 50mm thick M-15 grade C.C. flooring, making channels, 80mm thick stone slab covering with 40mm thick M-15 grade C.C. flooring, Cement cover with frame of 450mm dia, earthwork etc. complete as per design including disposal of surplus earth within 50 mtr. lead. Depth up to 0.5 M |
| 143 | Construction of chamber in all type of soil with 300 mm thick masonry in CM 1:6 m 10 cm thick C.C. 1:5:10 in foundation, 20mm thick insider plaster in Cm 1:6, finished with floating neat cement, 50mm thick M-15 grade C.C. flooring , earthwork etc. complete as per design including disposal of surplus earth within a lead of 50 mtr. Inside size 600 x 450mm depth upto 0.5 M Cement cover with frame. |
| 144 | P & F C.P. brass Urinal Flush Pipe set complete with flanged brackets of approved make.For 2 Urinals |
| 145 | Providing & Fixing premium qulaity WVC Urinal with PVC waste pipe, dome couplings, concealed iron brackets or screws etc. complete.Flat Back (large) or half stall size 590x375x390 mm. |
| 146 | P & F Flush Cock / Flush Valve (IS : 9758 Mark) for WC of approved quality make :do-) concealed 25mm nominal bore. |
| 147 | Providing and fixing 1st quality standard white, grey, ivory, fume red brown, light green, light blue and other light shades ceramic glazed vitrified tiles with water absortion less than or equal to 0.08% confirming to IS:13753 & IS : 15622 in floors, steps etc. laid on a bed of neat cement slurry finished with flush pointing in the white cement mixed with pigment to match the shade of the tile complete (excluding the cost of cement plaster on walls and pillar).Size 600mm x 1200mm, thicknes 8mm to 9mm |
| 148 | Add extra for Fixing glazed/ Ceramic/ Vitrified floor tiles with cement based high polymer modified quick-set tile adhesive (Water based) conforming to IS: 15477 , using 5kg. adhesive per sqm of tile area, in average 3mm thickness instead of cement mortar. |
| 149 | Supply of dry manure including loading unloading,transportation & stacking at site. |
| 150 | Compost |
| 151 | Vermi compost |
| 152 | Supply of different sized pots at site store including loading unloading & transportation etc. complete. |
| 153 | Cement pot 450 mm size |
| 154 | Cement pot 525 mm size |
| 155 | Supply of different varities of tree/shrubs/climbers according to height and age of the plant at side including loading/unloading & transportation etc.complete |
| 156 | Different flowering plants 900mm to1500mm |
| 157 | Different varieties of shrubs 600mm to 900 mm |
| 158 | Different varieties of climbers 900mm to 1500 mm |
| 159 | Supply of different varieties of bougainvillea in ply bags/earthen pot according to height growth and age of plant at site including loading unloading and transportation etc. complete Different varieties of bougainvillea 600mm to 900mm |
| 160 | Supply & Planting of shady plants ( Neem. Peepal, Goolar, Jamun, Imli or other specified) along road side including the following activities:- |
| 161 | Preparation of soil including cleaning & removing of unwanted shrubs removal of stones & garbage. |
| 162 | Supply of plant at site of two years of age & height more than 1.50 Mtr. |
| 163 | Supply of dry manure(Farm yard manure organic) |
| 164 | Supply of Insecticides. |
| 165 | Digging of pits size 60x60x60 cms. Including removal of stones. Manuring application of insecticides & watering at least 1.5 Liter per plant after planting |
| 166 | Half brick Circular tree guard in second class bricks, internal dia 1.25 meter and height 1.20 meter above ground and 0.20 meter above ground and 0.20 meterr below ground. Bottom two courses laid dry and top three couses in cement mortar 1:6 ( 1 Cement : 6 Sand) and the intermediate courseses being in dry honey comb masonry. As per design complete. |
| 167 | Watering to plants |
| 168 | Maintance of plants by the contractor including pits, preparation of Thavala Hoeing weeding etc & application of insecticiedes etc. & security. If the plant die during maintence contractor has to rplace same heingh plant at his own cost. |
| 169 | Supply & Panting of ornamental plants ( Kachnar, Amaltas, Gulmohar, Arjun, Kala, Siris, Jacranda etc. or other specified) along road side including the following activities :- |
| 170 | Preparation of soil including cleaning & removing of unwanted shrubs removal of stones & garbage |
| 171 | Supply of plant at site of two years of age & height more than 1.50 Mtr. |
| 172 | Supply of dry manure( Farm yard manure organic) |
| 173 | Supply of Insecticides |
| 174 | Digging of pits size 60x60x60 cms. Including removal of stones. Manuring application of insecticides & watering at least 1.5 liter per plant after planting. |
| 175 | Half brick Circular tree guard in second class bricks. Internal dia 1.25 meter and height 1.20 meter above ground and 0.20 meter below ground. Bottom two courses laid dry and top three courses in cement morter 1:6(1 Cement : 6 Sand) and the intermediate courses being in dry honey comb masonry. As per design complete. |
| 176 | Waterring to Plants. |
| 177 | Maintenance of plants by the contractor including pits. Preparation of Thavala Hoeing weeding etc. & application of insecticides etc. & security. If the plant die during maintencance contractor has to replace same height plant at his own cost. |
| 178 | Planting of trees /shrubs/ hedge and climbers plants at desired distance in row and watering |
| 179 | Ornamental Plants of different varieties Bamboo plant of Different varieties P.B(14”X14”) - 4’-5’ |
| 180 | Construction of tube-well from ground levels and upto 100 Meter depth and above to accommodate housing and assembly pipe of following sizes in all types of alluvium strata by percussion/ rotary drilling method and with gravel as per IS:4097-1967 and packing as per IS:2800 (Part I -& II) 1979 as amended upto date (the work includes the cost of gravel & its primary packing and packing during development, lowering of housing & strainer assembly pipes, with supply and wrapping of coir-rope, wherever necessary, for arresting fine sand particles. The work will not include cost of housing pipe and strainer pipe assembly and development work, but work would be completed after obtaining sand free water).200mm –do-. |
| 181 | Construction of Tube-well upto 100 Meter depth and above in all type of rocks by DTH system and over burden, to accommodate casing pipe of following sizes in all types of soils and over burden including lowering of casing pipes, but excluding cost of casing pipes as per IS : 2800 (Part I & II) 1979 specifications. The work would be completed after obtaining sand free water. The tube well should have a throughout bore as per nominal dia of casing pipe:200 mm –do- |
| 182 | Supply of ERW M.S. black casing pipe ISI marked (IS:4270/1992) of grade Fe410 of following sizes at site of work.200 mm Nominal bore of pipe |
| 183 | Supply of strainer pipes made of ERW M.S. black pipe ISI mark of following sizes at the site of work including required size of slotting as per IS:8110-1985200mm-do-.. |
| 184 | Testing verticality of tube-well by plumbing system and yield test and draw down test by pumping system as per IS: 2800 (Part II) 1979. |
| 185 | S & F tube well cover of M.S.sheet (6mm thick) with nuts and bolts complete for casing size:125mm dia |
| 186 | S & F M.S. clamp, set of 50 ×6mm flat iron with nuts and bolts etc. for holding the riser pipe assembly of submersible pump set. |
| 187 | Providing & lowering of G.I. Pipes, flange pipe including rubber washer and nuts of 8 mm dia complete in all respect I.S.1239 Marked.B Class 50 mm dia |
| 188 | Development of tube well as per IS specification using suitable compressor to give sand free water for required yield of the gravel packed tube well. |
| 189 | Supply & lying River-gravels of following sizes in recharge shaft, filter pit after screening & washing from kachha shift without deduction of voids Size 9 to 12 mm |
| 190 | SITC of Radial / mixed flow water and anti-corrosive liquid filled submersible motor pump sets suitable for 100/150mm dia borewell. The size of adopter fixed on top of the motor should exceed the top of coupler , for safegaurd the coupler. The job includes labour part of lowering of riser pipe G.I./ H.D.P.E. with rope, cables & pump, installation of complete fitting and accessories, jointing of electrical cables up to Starter. All labour for testing of submersible pumps set and supply of water to water mains, complete in all respect. |
| 191 | 150 mm diameter Submersible pump shall have following HP Rating, phase, Head range, Discharge range respectively.10.0 HP, 3-Ø, (110 - 212)Mtr, (400-167) LPM |
| 192 | SITC of Copper Bonded rod Earthing with high tensile strength (more than 600 N / sq.mm low carbon steel rod molecularly bonded with Copper thickness (250 microns) and confirming to UL 467 of following size and length and as per point mentioned (a), (b), [c), (d), (e) below :- |
| 193 | (a) Bore a hole of dia. 100 mm of required length, Place the rod in the centre of Hole |
| 194 | (b)Earth enhancing compound to ensure the moisture content and electrical conductivity, 25 kg for 3000 mm. The compound shall be tested form NABL accredited lab for low resistivity (less than 0.12 Ohm - meter) & high conductivity in nature with carbon as a major content in accordance with IEC 62561-7 |
| 195 | © Connect the rod with copper Strip/Conductor/Wire with suitable clamp made from tinned copper and SS 304 Bolt |
| 196 | (d) Place Heavy duty weather proof poly-propylene earth inspection chamber as per requirement of IS/IEC 62305 and tested as per IEC 62561-5 with lockable Jam free lid suitable for safe working load 60 kN of round / square size 250 mm, and Height 250 to 300 mm. |
| 197 | (e) Testing of earth resistance for value of 5 ohms or less as required. |
| 198 | (f) Test certificates for confirming above standards from OEM is mandatory. |
| 199 | 17.2 mm thick and 3 Mtr. Long |
| 200 | Supply & Laying following size earth strip in horizontal or vertical run in surface by means of Earth strip DMC Insulator including riveting/ soldering/ welding, Jointing shall be done by overlapping double the width of strip and with 2 set of Brass (for Cu strip) / GI (for GI Strip) nut bolt & spring washer spaced at 50cm making connection etc. as required.32mm x6mm G.I. ( Hot Dipped ) Strip |
| 201 | Supply and Laying ISI marked P.V.C. insulated submersible cable confirming to(IS:694) and as per IS 8130 : 2013 of 1.1 kV grade . Wire should be made from copper, stranding in acc. to IS:8130/IEC 60228 for lower watt loss , oxygen free for less chances of oxidization, insulation PVC type A/C/D , flame retardant as per IS 10810-53, better amperage rating as per IS:3961 part 5, existing pipe / open trench / Cable tray / on surface including making connection etc. as required.4.0 Sq.mm 3 core flat / Round |
| 202 | SITC of IP 54 OEM Fabricated DOL/Star-Delta Starter panel with switchgear selection as per Type-2 Coordination Chart and made out from 1.6 mm thick powder coated CRCA sheet, enclosure comprising of over load protection relay, short circuit & single phasing protection(for three phase pumps), Illuminated ON / OFF push buttons, ammeter, voltmeter, indicating lamps, 2P/4P MCB etc. suitable for following rating motors complete in all respect. 7.5 HP to 10.0 HP ( Star / Delta starter ) |
| 203 | NON BSR ITEMS : |
| 204 | Providing and fixing Toilet cubical of Greenlam, Merino, Century or equivalent make (standard height of cubicle is 2025mm with 600mm door size width) made up of thermosetting resign treated high pressure ,self supporting decorative compact laminates with permanently incorporate anti Viral(ISO21702:2019), anti-Fungal(ASTN:G21-2015) & anti-bacterial agents(under JIS Z2801:2000 certification) during manufacturing .Compact board should be resistance to water immersion through permissible increase on thickness and mass <0.60% and board density >1.35kg/cm3 and fulfilled the criteria of green guard gold certification and manufactured under EN438-2&3:2005 standard. 12mm thick compact board should be Moisture resistant, Impact resistant, termite resistant ,Scratch resistant ,Weather and climatic shock resistant. Finish of compact laminates should be suede finish which includes door, pilasters and intermediate panels finished with approved texture/shades as per IS2046 and fulfilled the criteria of fire retardant under BS-476/97 and EN438-6 with classification of BS1D0 standard. |
| 205 | Pilaster to be supported with SS(grade316) adjustable foot and intermediate panels will attached to the wall with the help of approved SS(grade316) channels and all required hardware, made up of stainless steel as per manufacturer’s specification. Door knob, gravity hinges,Thumb turn locksets with occupancy indicators, coat hooks with door stoper, U channel, top rail with corner connector, adjustable foot/pedestal, Rubber noice deafening tape, screw & wall plugs should be approved under the instruction of Engineer-in-charge. The top fitting should consist of SS316 round top rail which will get fixed with pilaster, with SS316 panel tube holder ,SS316 corner bend (connected with top rail ) will be use in corner of cubical in absence of brick wall, SS wall fixing is used only on the wall which will hold the SS top rail. All screw will of 304 grade in SS with stain finish. All pilasters are supported by SS bottom cladding . The base of the stainless steel bottom cladding will be anchored to the floor with a clearance height upto 150 mm.Finish and colour of Toilet cubical should be approved under guidance of engineer-in-charge. |
| 206 | Supply, Installation, Testing & Commissioning of anti-corrosive bobbin wound Fiber Glass side mount Sand Filter having size of 1200 mm dia & flow rate 56.5 m³ per hour at maximum working pressure is 2.5 kg/cm², maximum operating temperature 50 degree Celsius. complete with collector arms and diffusers made from unplasticised PVC and polypropylene, pressure gauge, manual bleeder, water drain, empty drain for filter etc., as directed and approved by Engineer in charge. (Make :-Watermate/ ASTRAL/ Aquanomics/ Aqvastar or equivalent company) |
| 207 | Supply, installation & commissioning of graded filter media for side mount sand filter quartz media 1)silica sand 0.4-0.8 mm (2/3rd) 2) gravel 1-2 mm (1/3rd) as directed and approved by Engineer in charge. Make: Watermate/ ASTRAL/ Aquanomics/ Aqvastar or equivalent company |
| 208 | Supply, Installation, Testing & Commissioning of Multi-Port Valve (special polymer made 6-way multiport valve (bolts mounted) with lever action handle with quick connect barrel unions with BS/ASTM connection, integral sight glass for watching backwash cycle, manometer with air bleed apparatus for monitoring and varying the pressure of filtration system) assembly suitable for 56.5 m3 filter of 1200 mm dia complete with all accessories- as directed and approved by Engineer in charge. Make :- Watermate /ASTRAL/Aquanomics/Aqvastar or equivalent company |
| 209 | Supply, Installation & Commissioning of Centrifugal Recirculation Pump with Leaf Strainer. Port Size: 2\\" x 2\\" Phase: Three Power: 4.0 HP, 8 m Head, Electric Motor working on 400/440 V, 50 Hz, 3 Phase Electric supply, corrosion resistant, high grade stainless steel motor shaft ,2850 RPM motor, high chemical resistance with all metal internal components being stainless steel complete with all fittings as directed and approved by Engineer in charge. Make: Watermate /ASTRAL / Aquanomics/ Aqvastar or equivalent company |
| 210 | Supply, Installation & Commissioning of Surface Mounting SS Under Water LED Lights of 18W-12V, I.P.68, Illuminance of 415with stainless steel face ring and with waterproof standard and with1.5SQ.MM-3Core Copper Cables for Under Water LED Lights from Filter Plant Room and up to the LED Light Fixtures including conduits, tee, elbows, bend, junction box etc. for underwater light as directed and approved by Engineer in charge. Make: Watermate /ASTRAL/Aquanomics/Aqvastar or equivalent company |
| 211 | Supply, Installation & Commissioning of LED Lights Transformers suitable to operate 18W - 12V Underwater LED lights, I.P.68, Illuminance of 415 with complete as directed and approved by Engineer in charge. Make: Watermate /ASTRAL/Aquanomics/Aqvastar or equivalent company |
| 212 | Supply & Installation, Testing & Commissioning of Dosing Pumps capacity, 0-5 ltrs per Hour. power 12 V, Pressure 8 Bar, Complete with 6 Amp Switch Socket arrangement as required FRP Tank for preparation of solution, Capacity 100 ltrs. with stirrer etc. complete.as directed and approved by Engineer in charge. (Make :- Watermate/Oceanstar/ EDOSE/Nuton/Accord)or equivalent company |
| 213 | Supply & Installation, Testing & Commissioning of Anti Vortex Pool ABS main drain cover base plate of size 300 mm x 300 mm as directed and approved by Engineer in charge. Make: Watermate /ASTRAL/Aquanomics/Aqvastar or equivalent company |
| 214 | Providing and fixing of ABS pool floor inlet nozzle as directed and approved by Engineer in charge. Make: Watermate /ASTRAL/Aquanomics/Aqvastar or equivalent company |
| 215 | Providing and fixing ABS gratings in white color 12\\" wide, heavy duty with non-slip surface for safety, manufactured in weather proof (UV protected) polypropylene for long life as directed and approved by Engineer in charge. Make: Watermate /ASTRAL/Aquanomics/Aqvastar or equivalent company |
| 216 | Providing and fixing 304 grade 5-steps stainless steel ladders with anti-skid pads with proper anchoring, safe handrail as directed and approved by Engineer in charge. Make: Watermate /ASTRAL/Aquanomics/Aqvastar or equivalent company |
| 217 | Providing and fixing 304 grade Stainless Steel Trolley mounted suction sweeper pump of 1.0 HP, as directed and approved by Engineer in charge. Make: Kirlokar / Lubi / Texmo or equivalent company |
| 218 | Providing Deluxe pro leaf net bag type as directed and approved by Engineer in charge. Make: Watermate /ASTRAL/Aquanomics/Aqvastar or equivalent company |
| 219 | Providing Deluxe wall brush 18\\" long heavy duty, long lasting bristles with rugged high grade polymer handle and vary resistant bumper design with aluminum back as directed and approved by Engineer in charge.Make: Watermate /ASTRAL/Aquanomics/Aqvastar or equivalent company |
| 220 | Providing Stainless steel algae brush 250 mm heavy duty stainless steel bristles asdirected and approved by Engineer in charge.Make: Watermate /ASTRAL/Aquanomics/Aqvastar or equivalent company |
| 221 | Providing 24\\" Stainless steel vacuum head with wheels, brush, wiper and 80 m towing rope as directed and approved by Engineer in charge.Make: Watermate /ASTRAL/Aquanomics/Aqvastar or equivalent company |
| 222 | Providing Floating Hose pipe 15 M as directed and approved by Engineer in charge.Make: Watermate /ASTRAL/Aquanomics/Aqvastar |
| 223 | Providing Standard Telescopic handle 1.2m-2.4m of aluminum as directed and approved by Engineer in charge.Make :Watermate /ASTRAL/Aquanomics/Aqvastar or equivalent company |
| 224 | Providing Standard Telescopic handle 2.4m-4.8m of aluminum as directed and approved by Engineer in charge.Make :Watermate /ASTRAL/Aquanomics/Aqvastar or equivalent company |
| 225 | Providing Basic pH and CI test kit as directed and approved by Engineer in charge.Make :Watermate /ASTRAL/Aquanomics/Aqvastar or equivalent company |
| 226 | Providing Hardness Test Kit as directed and approved by Engineer in charge.Make :Watermate /ASTRAL/Aquanomics/Aqvastar or equivalent company |
| 227 | Providing TCCA-90 chlorine granules for disinfection as directed and approved by Engineer in charge. Make :Watermate /ASTRAL/Aquanomics/Aqvastar or equivalent company |
| 228 | Providing and fixing Aluminum life saving hook as directed and approved by Engineer in charge.Make :Watermate /ASTRAL/Aquanomics/Aqvastar or equivalent company |
| 229 | Providing and fixing Lifebuoy made of UV grade PE & PU foam filled, round shaped with retro reflective tape and grab line as directed and approved by Engineer in charge.Make :Watermate /ASTRAL/Aquanomics/Aqvastar or equivalent company |
| 230 | Providing and fixing Life Jacket made of durable, water resistant fabric that resist chlorine and UV degradation as directed and approved by Engineer in charge.Make :Watermate /ASTRAL/Aquanomics/Aqvastar or equivalent company |
| 231 | Supply, Installation, Testing & Commissioning of UV Sterilizer with Housing outside, U.V. Lamp of 75 W, glass tube and all other accessories with supports, inlet outlet connection with bypass arrangement complete with required accessories.as directed and approved by Engineer in charge.Flow rate = 42 M3/Hr.working Pressure = 2.5 Kg/SqmMake: Watermate /ASTRAL/Alfaa UV/Aqvastar or equivalent company |
| 232 | Providing & applying Waterproofing Treatment to Pool Walls and Floor using polymer modified 2-component cementitious compound and latex coating applied using brush, micro-concreting, injection grouting and fiber mesh work is done at wherever necessary1. Cleaning of the targeted surface2. Repairing with micro concrete, epoxy grouting, injection grouting and fiber meshetc. wherever necessary3. Pressure grouting with manual (140PSI) / machine work (40 PSI) wherever necessary4. Two coat of bonding agent (1:3:3 - chemical: water: cement)5. Two coat of single component acrylic polymer for modified cementitious chemical composition as directed and approved by Engineer in Charge.Make- Pidilite/MYK Arment/Perma |
| 233 | Providing & Fixing approved brand tiles of size 50mm x 50mm Porcelain Pool Mix Mosaic Tiles with thickness of 8mm of 0.032% water absorption general chemical acid resistant fixing by Laticrete/JK Cement/Kerakoll/MAPEI make White Mosaic Adhesives and White Epoxy Grouting fixing by FINA standards specifications or as per lane marking of swimming pool complete as directed by Engineer in charge.Make- Italia/Piccolo/Keramika/Onix/ Mossaico or equivalent company |
| 234 | Dismantling Plant- Dismantling of existing plant and carriage including M.S./G.I/C.I./Other material pipes, fittings ,angles, girders, other section as per directed and approved by Engineer in charge |
| 235 | Supply & Installation of Office Table, overall size of the unit is (W)1200mm x (D) 600mm x (H) 750mm. Table top made of 18mm thick pre-laminated particle board with 36 mm thickness on all edges and 1mm thick edge bending all around the top. The rest of the structure of the unit made of 18mm thick pre-laminated particle board. The Table shall have 1 no. of drawers running on sliding channel with locking system and one openable shutter with lock and one shelf in the inner side of the unit with locking system, including keyboard rack as per sample and design approve by engineer in charge. |
| 236 | Supply of visitor fix type chair, chair base made of 25mm dia SS chrome finish single pipe having studs. Seat of the chair shall be made of 12mm thick hot pressed ply covered The cushioned seat assembly shall consist of insert molded polyurethane foam upholster with foam laminated mesh fabric the insert molded foam is assembled over a load bearing plastic seat cover. The back shall have made up of two-piece injection molded frame. The inner frame shall be upholstered with mesh fabric and mounted on the main assembly, the arm set shall be fixed with the seat and back. As per design and sample approved byengineer in charge. |
| 237 | Supply of Center Table size: 1200 x 600 x 450mm (L x W x H) Table top: Table top made out with 18mm thick pre-laminated particle board with four side edge band finish. The whole table is supported on four leg of and equal size which are made out of 18mm thick pre-laminated particle board with PVC edge banding of matching color. Table having 5 mm thick black tinted glass. The entire table is complete in all respects and made as per specification and as directed by engineer-in-charge. |
| 238 | Supplying of 3-seater sofa with arm fully cover PU leatherite/fabric of Up to Rs. 450/- per mtr. Inner size of sofa Seat 5'6'' X 21'' and back 5'6'' X 20'‘. Inner structure made by Pine wood frame, nails and foaming pasted by adhesive and F-nails compressed by auto nail machine. 40 Density foam seat,32 density foam back. Complete in all respect as per design and sample approved by Engineer-in-charge |
| 239 | Supply of Umbrella-for outdoor purpose made of high quality , highly durable andwaterproof material with solid and durable stand Complete in all respect as per design and sample approved by Engineer-in-charge |
| 240 | Supply of Deck chair/loungers-for outdoor purpose ergonomic design for comfort and support with adjustable backrests made of high quality , high durable and water proof material Complete in all respect as per design and sample approved by Engineer-in-charge |
| 241 | Deduct for Taking away dismantled unserviceable M.S Tank, pipes, fittings, steel grills, M.S. bars, G.I. Angles, T- Iron frames, flats, G.I. Pipes / fittings, C.I. For all leads and lift as per direction of Engineer in Charge. |
| 242 | Providing and laying ANTI SKID designer floor tiles for deck area thickness to be specified by the manufacturer of 1st quality conforming to IS 15622 of approved make in colors shade except white ivory grey fume red, brown laid on 20mm thick cement mortar 1:4 (1 cement: 4 sand) design as per directed and approved by Engineer-in-charge. Make- Simpolo/ Larson/ Pavit/ equivalent company |
| 243 | Designing, supply, erection, commissioning and testing of 5‘dia Ring fountain surrounding the existing stone fountain. The nozzle spacing should be 150 mm c to c, adjustable brass ball joints with chrome plating. The pipe should be made of GI pipe B class with epoxy coating, Nut bolts, Gaskets, pipework, manifold sockets, and nozzles made of precisionmachined brass, including all final epoxy finishing work of pipe surface etc. Material of construction of various components Manifold: steel-Epoxy coated Control Valve: Brass/Gunmetal of ISI marked Pipe work: GI with nominal dia 50 MM Nozzle: Brass Chromium plated Mounting Stand: fabricated steel-galvanized/epoxy coating |
| 244 | Designing, supply erection, commissioning and testing of 2 HP Monoblock submersible pump of Kirlosker or equivalent company make AC 1 phase 220/240 Volt, 50 cycle, supply with foundation bolt, suction stainless steel mesh cover 10 Mtr. Of 2.5 sq mm submersible cable duly insulated of finolex make. (1x10 mtr.) Make: Kirlosker or equivalent company |
| 245 | Supply and fixing of 2 HP panel box for above pumps of steel sheet enclosure with front door back wall mounting with red oxide undercoat and paint finish. Panel comprising 1 No main incoming single-pole MCB, condenser start-stop push-button switch; all accessories must be of Cat. I duly tested. |
| 246 | Supplying Electric Control Panel suitable to operate filtration system with GSM Based Real-Time Monitoring System having necessary sensors & Web-based application to indicate the following parameters- 1. Hours of Operation 2. Flow 3. Chlorine Level 4. Turbidity 5. pH Level Also including, flow meters, flow sensors, sampling valves, MCCB, MCB, MS CRCA Sheet Panel enclosure, powder coated RAL, all switchgear Schneider make, power TB, control TB etc. Make: Watermate /ASTRAL/Aquanomics/Aqvastar or equivalent |
| 247 | HYDRAULIC WORK FOR SWIMMING POOL |
| 248 | PUMP SUCTION PIPIING: Supply installation & commissioning of Recirculation pump piping dia 10kg /cm2 UPVC pipe from balance tank up to circulating pumps suction with Foot valve, elbow, strainer, pipe end MS Silicon flange, rubber gasket, nut bolt etc. complete as per requirement of plumbing |
| 249 | Supply installation & commissioning of filter room piping from pumps dia 10kg/cm2 PVC pipe main 110 /90/75/63/50mm size with control valve and Non return Valve etc.complete. |
| 250 | CHEMICAL DOSING Supply installation & commissioning of All inter connecting piping including suction form return line and discharge piping of 15mm PVC transparent with non-return valve inbuilt in automatic chemical dosing system with strainer FILTER |
| 251 | WATER RETURN LINE PIPE VELOCITY : 2.5M/SEC Supply installation & commissioning of delivery UPVC piping from filter room to swimming pool inlet 10 KG 75/65/50mm pipe size filter room up to the bottom distributing piping inside the swimming pool complete with elbows, pipe ends, MS silicon flanges MS nut and Bolt rubber gasket GI nut bolt etc.complete |
| 252 | BOTTOM DISTRIBUTION PIPING Supply, Installation & commissioning of PVC bottom distribution piping in 75/63/50mmOD/10 kg pressure pipe |
| 253 | OVERFLOW LINE PIPE VELOCITY : 0.8M/SEC Supply installation & commissioning of Over Flow piping in PVC pipe 160mm from swimming pool overflow water channel collection pit & up to the balancing tank |
| 254 | SUCTION LINE PIPE VELOCITY : 1.2 to 1.5M/SEC Supply installation & commissioning of wall vacuum point piping from swimming pool to main circulation pump 63 MM dia 10kg/cm2 pipe main to main UPVC header of 110mm size with control valve and Non return Valve etc. complete. |
| 255 | DRAIN PIT PIPING Supply installation & commissioning of drain piping in UPVC60mm/10kg size from main drains located inside the swimming pool & up to balancing tank bottom complete CI valve & operating MS handle, abs Drain plate of size 110mm with base frame connectors with flanges & Nut bolt etc. complete with elbows, pipe ends, MS silicon flanges MS nut and Bolt rubber gasket GI nut bolt etc. complete All pipes shall be of ISI mark, Supreme/finolex/astral/prince OF 10KG/CM2. All PVC / PP valves shall be of minimum PN10 rating. |
| 256 | All standard fittings like bends, elbows, tees etc. should be of similar rating of the pipes. However, in cases where special fittings are required and the same are to be fabricated on site due to non-availability anywhere in the Indian market, then the contractor has to ensure that the fittings are fabricated of high grade chopped PVC fiber/ ravings and should be capable of withstanding working pressure of at least 10kg/cm2 and drain pipe 4/6 kg/cm2 PRINCE/ SUPREME/ ASTRAL /ASHIRWAD/ DUTRON/ EQUIVALENT |
| 257 | Add: GST 18% Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Sep 29, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedOct 07, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 7 daysOct 08, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 8 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender