Tender For Widening Of Existing Roads Infront Of 97 Arty Bde C At Chh Sambhajinagar Cantt
Tender Value
43.38 Lakhs
Estimated cost
Bid Submission
19 Oct 2026
1 days left
EMD
87000
Bank guarantee accepted
Document Fee
500
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Ahmednagar → Maharashtra
EMD Exemption
Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for Widening Of Existing Roads Infront Of 97 Arty Bde C At Chh Sambhajinagar Cantt
BOQ
| Sl. No. | Item Description |
| 1 | Excavation over areas n exc 1.5 m deep and getting out in any type of soil all as directed |
| 2 | M&L for Moorum/red bajri filling in floors or pavings, laid in layers n exc. 15 cm thick spread, levelled and rammed including watering complete all as specified and as directed. |
| 3 | M&L for 200mm thick (compacted thickness) Granular Sub Base (GSB) of Grade-I as per Table 400-1 of MORT&H, IRC specification laid with mechanical pavers, rolled and compacted to required gradient and camber with 8 to 10 tonne power roller and vibratory roller complete as per MORT&H specification clause 401 including all tools and plant and mangaging diversion all as specified and as directed. |
| 4 | M&L for laying and compacting 150 mm thick (compacted thickness) Wet Mix Macadam (WMM) laid in two layers of 75 mm each grading as pe table 400-13 of MaRTH specifications for Road and Bridge works 2013 manufactured in WMM plant material comprising of clean, crushed, graded aggregate and granular material premixed with water to a dense mass, spreading with sensor paver and rolling with vibratory roller of capacity 80-100 KN static weight and consolidating to required gradient and camber complete all as specified and directed. The finished surface tolerances to be as per Table 900-1 of MaRTH specifications for Road and Bridge works 2013 |
| 5 | M &L preparing unsurfaced WBM/WMM surfaces by brushing with wire brushes for removing caked mud etc. sweeping with brooms and finally cleaning the surfaces with mechanical compressor to remove all loose dirt etc and Applying evenly a prime coat of Cationic Bitumen Emulsion SS1 confirming to IS: 8887 at a rate of application of 8.5 kg/ 10 sqm on surface on WMM/WBM as specified in Table 500-3 of MoRTH specification for road and bridge works 2013, using mechanical sprayer complete all as specified and directed. |
| 6 | M &L preparing existing black top surfaces by brushing with wire brushes for removing caked mud etc. sweeping with brooms and finally cleaning the surfaces with mechanical compressor to remove all loose dirt etc complete all as specified & directed. |
| 7 | M &L for applying evenly priming/tack coat with bituminous primer (paving VG-10 grade bitumen) @ 2.5 Kg per 10 Sqm complete all as specified and as directed. |
| 8 | M&L for Premixed bituminous Macadam (consolidated thickness 75mm or less) with 4% binder content using paving bitumen of VG-30 grade by weight of total mix laid/rolled and compacted to required camber and gradient complete all as specified and directed. |
| 9 | M&L for Bituminous premix asphaltic semi dense concrete 40mm consolidated thickness with 5.00% binder content by weight of total mix, rolled and compacted with using 8 to 10 tonne capacity power roller to required camber and gradient complete using paving bitumen of penetration VG-30, laid to required camber and gradient mixed in hot mix plant using design mix and laid with mechanical paver and rolled to a uniform smooth surface all as specified and directed by Engineer-in-Charge. |
| 10 | M&L for preparation of road surface and applying thermoplastic reflective paint for marking of minimum 2.0 mm thick single coat as a centre line or edge line etc, road marking n exc 100 mm width using thermo plastic paint (Hot application) white/yellow by indigenous modern propelled road marking machine as directed including all ingredients such as binder, glass beads, titanium dioxide, calcium carbonate, inter fillers etc, thermoplastic requirement for glass beads shall be confirming to BS-6086 of most specification including spraying of glass beads etc complete all as per manufacturer's instructions and complete as all specified and directed. |
| 11 | Supply and fixing in repair cat eye solar reflective type of size 100mm x 100mm x 18mm with PAMA striplens relector fixed with and incl MS stud of suitable size as per manufacturers instructions. Make : DA 978 of Darkeye or equivalent model of makes specified. |
| 12 | Supply and fix solar cat eye aluminium alloy shall (100% water proofing design according to 65) of size 125mm x 125mm x 25mm (shank 65mm) of high efficiency Mono crystaline solar panel 2.4V/0.3 watt one NI-ed rechargeable battery (1.2V/1600MA) consisting of super bright LED with 1,000 to 18,000 mcd complete as per manufacturers instructions etc all as specified and directed. Make: 3M/Green lite/Dark eye |
| 13 | S&F road side unbreakable convex mirror / security mirror/ traffic mirror for road safety with installation kit & adjustable fixing bracket (nuts & Bolts), ISO Certified 9001:2015, of size 800mm dia, made up of polycarbonate, mounted on MS pipe of 2.1m long and dia of pipe is 80mm including RFR, removal and two coat of synthetic enamel paint over a coat of zinc chrome primer in MS pipe including necessary excavation and earthwork in any type of soil for fixing and embedding the MS pipe on ground with hold fast using PCC (1:2:4) type B1 using 20mm graded aggregates (block size 0.3m x 0.3 m x 0.45m below GL) and proper grouting, complete all as specified and directed. |
| 14 | S&F in repairs ABS plastic speed bump/speed breaker in parabolic convex shape and of size 730mmx245mmx70mm made out of steady plastic, dovetail interlocking sub units, jointed and fixed to make the bump perfectly uniform, bump made out of recoloured material (black/yellow) and UV stabilisers to keep them perfectly colourful, studded with reflectors on either side to make it clearly visible to motorist during night hours, including PCC (1:2:4 type B1) filling in speed breakers, complete all as specified and as directed. |
| 15 | Removing excavated material to a distance n.exc 50m and depositing where directed at a level n. exc 1.5m above the starting point in any type of soil all as directed |
| 16 | Demolition of stone/ brick masonry built in cement or cement lime mortar as in portion ordered and directed. |
| 17 | M&L for near ground level factory made kerb stone of M-25 grade cement concrete in position to the required line, level and curvature, jointed with cement mortar 1:3 (1 cement: 3 coarse sand), including making joints with or without grooves (thickness of joints except at sharp curve shall not to more than 5 mm), including making drainage opening wherever required and taking down old damaged kerb stone complete all as specified and as directed. |
| 18 | M & L Continuous brick edging, with width equal to the width of the brick, laid dry on end vertically complete all as specifid and as directed. |
| 19 | Dismantling of posts or struts (wood, steel or RCC) embedded in concrete, brick work, masonry etc, any section including taking out embedded portion and making good disturbed ground complete all as specified and as directed. |
| 20 | Dismantling fencing wire mesh,any type complete all as specified and directed. |
| 21 | Excavation in post holes in any type of soil each not exceeding 0.5 Cum, getting out, returning filling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25 cm, watering and removing surplus soil to a distance not exceeding 50 m and making good surface all as specified and as directed. |
| 22 | M&L for PCC 1:2:4, type B2, using 40mm graded stone aggregate as in foundations filling and mass concrete for fixing fencing posts and similar work all as specified and as directed. |
| 23 | S&F mild steel angle/flat iron as in posts and struts in fencing and flat iron for securing barbed/chain link fencing of any description including drilling holes, notching for wire etc and similar work conforming to Fe-290 Gde E-165 complete all as specified and as directed. |
| 24 | S&F mild steel round bars (10mm dia) as line bars for fixing chain link fencing, conforming to FE 410 W( Gde-E-250) quality or FE 290 (Gde -E-165) complete all as specified and as directed. |
| 25 | M&L for machine made, mild steel bolts, 10 mm dia shank with hexagonal or square head one end and screwed the other or screwed both end, each screwed end to be fitted with, washers and one hexagonal or square nut, length length of bolt exc 5cm but n exc 10cm complete all as specified and as directed. |
| 26 | Supply only Chain link MS galvanisd fencing, any size or type Complete all as specified and as directed. Notes :- (i) Chain link fencing mesh and gauge of wire to be decided by Engr-in-Charge.(ii) Payment shall be allowed after ascertaining weight of chain link fencing as per actual at site through BOO as ordered by GE. |
| 27 | Fixing only chain link fencing including line wires, any mesh, size and type to any type of standards, rails, straining bolts etc including provision of bindig wire complete all as specified and as directed. |
| 28 | S&F 300 mm internal dia reinforced cement concrete pipes of approved make, class NP2, laid and jointed in cement mortar with collars complete all as specified & directed. (PCC shall be measured and paid for seperately under respective item). |
| 29 | M&L for PCC 1:4:8 type D-2, using 40 mm graded stone aggregate as in concrete bed to drain pipes, any type, of 300 mm internal dia including packing under and hunching against the sides of the pipes after they are laid & tested complete all as specified and directed. |
| 30 | M & L for brick work with fly ash bricks old size straight or curved on plan exc 6 cm mean radius in Cement mortor 1:6 etc including demolition of old brick work above or below GL in foul conditions or in any other condition completed all as specified and directed by Engr-in-Charge |
| 31 | M&L for Cement concrete 1:3:6, type C1 using 20 mm graded stone aggregate as in coping complete all as specified and directed. |
| 32 | M&L for Rendering 15 mm thick in CM 1:4 on brick or concrete surfaces including finishing the surfaces even & smooth without using extra cement complete all as specified and directed. |
| 33 | M&L for preparation of old painted surfaces of steel and iron work of any description over 10cm width or girth and applying one coat of synthetic enamel paint complete all as specified and as directed. |
| 34 | M&L for preparation of new steel surfaces over 10 cm width or girth applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified. |
| 35 | M&L for preparation of newly plastered concrete surfaces over 10 cm width or girth applying two coats of synthetic enamel paint over a coat of primer complete all as specified. |
| 36 | Dismantling of ACSR or AAC conductors of any size and any description from any heights/ poles or any location, complete all as specified and as directed . |
| 37 | Dismantling of unserviceable steel structure, cross arms, bracings, supports, clamps etc from LT pole of any type complete all as specified and directed. |
| 38 | Dismantling insulators any type and any size from poles of any height complete all as specified and as directed. |
| 39 | Dismantling old existing LT stay complete all as specified and directed. |
| 40 | Taking down old existing LT pole complete all as specified and directed. |
| 41 | M&L for taking down unserviceable/Serviceable street light fittings from LT Pole including bracket, Junction box electric connection, keep safe custody in MES yard complete all as specified and directed. |
| 42 | Supply and errection of steel tubular swaged poles complete with cast iron base plate , finial tapper plug , bolts,nuts & screws as specified type 410 SP - 31, 9.00 Mtr long including one coat of red-oxide zinc chrome primer and two coats of aluminium paint on surfaces exposed to view and making 30cm wide strips (total 5 Nos) with yellow and black paint alternately on external surface above PCC benching and painting with bituminous paint internally including writing the pole number in white letters on black background complete and externally for portion embedded in PCC, complete all as specified and directed. Note :- Excavation & earthwork and PCC in foundation of poles,coping etc shall be measured and paid separately |
| 43 | S & F PVC weather proof, hinged door, junction box with Aluminium bus bar, 240V, Neutral link and 1 No MCB SP of 6/10 Amps, necessary fixing arrangement such as clamps, nut, bolts, etc including dismantling old unservieable junction box all as specified and directed. |
| 44 | S&F in replacement bracket for street light, made out of GI Pipe medium grade of suitable size (40 mm dia and 1.2 mtr long) bent to shape, fixed with and including necessary heavy duty clamps of suitable size including painting the clamps with two coats of synthetic enamel paint over a coat of primer all as specified and as directed. |
| 45 | S&F in replacement LED street light fitting 90 Watt 230 V AC outdoor type with high pressure die cast aluminum hosing and heat resistant complete with driver, lamp bracket with impact and corrosion resistant including thermal management in multiple optics complete with IP 65/66 protection complete including PVC copper wire 1.5 sqmm of suitable length for connection of street light from Overhead conductor /junction box complete all as specified and directed. |
| 46 | S&F in replacement LED street light fitting 60 Watt 230 V AC outdoor type with high pressure die cast aluminum hosing and heat resistant complete with driver, lamp bracket with impact and corrosion resistant including thermal management in multiple optics complete with IP 65/66 protection complete including PVC copper wire 1.5 sqmm of suitable length for connection of street light from Overhead conductor /junction box complete all as specified and directed. |
| 47 | Supply, laying and testing 95 Sqmm 3.5 Core, XLPE insulated, PVC sheathed, ISI marked, earthed system, armoured heavy duty, electric cable with aluminium conductor, 1100 volts grade in trenches/wall/floor/pole complete and making connection including suitable size Aluminium lugs including taking out existing cable and cable covers all as specified and as directed. |
| 48 | All as per serial item No. 47 here in before but 70 Sqmm 3.5 core |
| 49 | All as per serial item No. 47 here in before but 35 Sqmm 3.5 core |
| 50 | All as per serial item No. 47 here in before but 10 Sqmm 4.0 core |
| 51 | Supply, laying and testing 10 Sqmm 2 Core, XLPE insulated, PVC sheathed, ISI marked, earthed system, armoured heavy duty, electric cable with aluminium conductor, 1100 volts grade in trenches/wall/floor/pole complete and making connection including suitable size Aluminium lugs complete all as specified and as directed. |
| 52 | M&L for LT Straight through cable jointing kit, heat shrinkable for 1.1 KV grade XLPE cable of size 70 to 120 sqmm 3.5/4.0 core complete with jointing material and accessories and testing after jointing complete all as specified and directed. |
| 53 | Supply and laying Double Walled Corrugated (DWC) HDPE pipe of nominal bore 110mm including 90 degree bends with coupler and rubber ring, conforming to IS :16205 Part 24 Type 450N, laid in trenches for cable protection complete, all as specified and as directed. |
| 54 | M & L for Double Walled Corrugated DWC HDPE Pipe (N-450) of outer dia 63 mm including 90 degree bends with coupler and rubber ring laid in trenches of size 63 mm suitable for cble protection complete all as specified and directed. |
| 55 | Supply and fixing PVC insulated and over all PVC sheathed, stranded copper conductor wire 1.5 sqmm x 3 core ISI marked in PVC Conduit 20 mm dia complete from light fitting to pole junction box complete all as specified. |
| 56 | M&L for 40 mm bore GI pipe light grade for cable protection ISI marked with all fixing accessories such as 40 x3mm Clamps of suitable length, Nut bolts and washers and fixed complete to walls and ceilings or laid in floors complete all as specified and directed. |
| 57 | Excavation in trenches by manual/ mechanical means (Hydraulic excavator) not exceeding 1.5 m wide and not exceeding 1.5 m in depth for laying of pipe, foundation etc. or for Shafts, wells, cesspits, manholes, pier holes, etc not exceeding 10 Sq m on plan, including dresssing of sides and ramming of bottoms, lift upto 1.5 m, including getting out any type of soil (soft/hard/dense soil) and disposal of surplus excavated soil to a distance not exceeding 50 m complete all as specified and as directed. |
| 58 | Returning, filling in including spreading levelling watering and well ramming in layer not exceeding 25 cm complete all as specified and directed |
| 59 | M&L for PCC (1:2:4) type B-1 with 20 mm gradded stone aggregate for copping of poles Pedestal (PCC) or mass filling complete all as specified and directed by Engr in Charge. |
| 60 | M&L for PCC 1:4:8 Type D2 using 40mm graded aggregate for base foundation of poles/posts complete all as specified and directed by Engr in Charge. |
| 61 | M & L for cutting the existing road/hard standing surfaces to a depth of 60cm and 50cm width and getting out for laying under ground cable including returning filling in, watering well ramming in layers not exceeding 25cm in soil and filling the top 15 cm thick with PCC type B2 1:2;4 (using 20mm graded stone aggregate) all as directed. |
| 62 | S&F in replacement galvanised, 80 mm bore, steel tubing, light grade, ISI marked, for protection of under ground cable on pole/wall/under road including taking out old unserviceable pipe complete all as specified and directed. |
| 63 | S&F in replacement galvanised, 100 mm bore, steel tubing, light grade, ISI marked, for protection of under ground cable on pole/wall/under road including taking out old unserviceable pipe complete all as specified and directed. Please Enable Macros to View BoQ information |
| 64 | S&F in replacement galvanised, 100 mm bore, steel tubing, light grade, ISI marked, for protection of under ground cable on pole/wall/under road including taking out old unserviceable pipe complete all as specified and directed. Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Sep 28, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedOct 19, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 1 dayOct 26, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 8 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender