Tender For special Repair Of Bldg No T-15 (Qm Store), T-16 (Cook House), T-17 (Dining Hall), T-18 And T-20 (Or Barracks), T-11 At Ilp Of Engr Regt Old Loc Near Santushti Welfare Kandra In Sukna Mil Stn Under Ge Sukna.
Tender Value
78.43 Lakhs
Estimated cost
Bid Submission
28 Oct 2026
22 days left
EMD
1.42 Lakhs
Bank guarantee accepted
Document Fee
1000
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Gangtok → sikkim
EMD Exemption
Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for special Repair Of Bldg No T-15 (Qm Store), T-16 (Cook House), T-17 (Dining Hall), T-18 And T-20 (Or Barracks), T-11 At Ilp Of Engr Regt Old Loc Near Santushti Welfare Kandra In Sukna Mil Stn Under Ge Sukna.
BOQ
| Sl. No. | Item Description |
| 1 | Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises, complete all as specified and directed. |
| 2 | M&L for Coloured Non - skid Ceramic tiles 7 to 8 mm thick area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match including 15mm thick Screed bed or bedding layer for laying floor finishes in CM 1:6 etc complete all as specified and directed by Engr-in-charge. |
| 3 | M&L for Coloured Non - skid Ceramic tiles 7 to 8 mm thick area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, on vertical surfaces such as skirtings, dados and risers to steps etc.. set and jointed in neat cement slurry and pointed in white or coloured cement to match including 10mm thick rendering on fair faces of brick work or concrete surfaces in CM 1:3 etc complete all as specified and directed by Engr-in-charge. |
| 4 | M&L for glazed ceramic colouered tiles in vertical surface 350x 250x 7 mm/ 450X 350X 7mm thick as in vertical surface such as risers of steps, skirting, dado etc., set and jointed in neat cement slurry and pointed in white or coloured cement to match the surface of tile over and including 10 mm thick rendering in cement mortar (1:4) finished even and rough, complete all as specified and directed. |
| 5 | Demolition of stone slabs and tiles laid, bedded and pointed in any mortar of any description or thickness in floors, aprons etc., complete all as specified and as directed. |
| 6 | M&L for 18-20mm thick granite stone slab machine cut, bedded over 15mm thick screed bed or bedding layer in cement mortar (1:6) and jointed with grey cement slurry and pointed with white cement with admixture of pigment to match the shade of granite stone including grinding and polishing complete all as specified and directed. |
| 7 | Labour only for rounding to edges of stone slabs one edge, such as in steps, cooking platform and other similar situations complete all as specified and as directed. |
| 8 | M&L for machine cut Kota stone slab flooring/ treads over and including, 20 to 25 mm thick over cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including grinding, rubbing and polishing and exposed edges of Kota stone shall be rounded complete over and including 20 mm thick screed bed or bedding layer in cement mortar (1:6) finished even and rough, complete all as specified and directed. |
| 9 | M&L for machine cut Kota stone slab as in vertical surfaces such as riser of steps/dado/skirting, 20 to 25 mm thick over cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including grinding, rubbing and polishing and exposed edges of Kota stone shall be rounded complete over and including 15 mm thick rendering in cement mortar (1:4) finished even and rough, complete all as specified and directed. |
| 10 | Demolition of cement concrete (unreinforced) in ground floor and pavings not exc 15 cm thickness (below or above ground level) complete all as specified and directed. |
| 11 | M&L for 75 mm thick plain cement concrete(1:3:6), type C2 (40 mm graded stone aggregate) as in flooring, plinth protection, hard standing, path etc including finish the surface even and smooth with using extra cement, complete all as specified and directed. |
| 12 | M&L for 75mm thick plain cement concrete (1:4:8), type D2 (using 40mm graded stone aggregate) as in sub-base, sub-floors, floors, pavings etc., all as specified and as directed. |
| 13 | M&L for chequered cement concrete tiles 20cm x 20cm x 25mm thick, set, jointed and pointed in neat cement slurry in floors with grey cement and no pigments over and including 15mm thick screed bed or bedding layer in cement mortar (1:6), complete all as specified and directed. |
| 14 | Demolition of brick work or stone/boulder masonary, built in lime mortar including all quions, arches, pillars etc, but excluding ashler facings, dressed stone work and precast concrete articles, all as specified and directed. |
| 15 | M&L for brickwork with fly ash bricks (old size bricks), straight or curved on plan exc 6m mean radius, built in cement mortar(1:6), complete all as specified and directed. |
| 16 | M&L for brickwork with flyash bricks, straight or curved on plan to any radius in half brick thick walls, built in cement mortar(1:4), complete all as specified and directed. |
| 17 | Taking down cement or cement lime plaster, any description on brick or stone masonry surfaces of walls etc including raking out joints, hacking for key, scrubbing down with water etc, complete all as specified and directed. |
| 18 | M & L rendering 15 mm thick in CM (1:4) on fair faces of brick work or concrete surfaces to be finished even and smooth without using extra cement mixed with per manufacture instruction Complete all as specified and as directed. (WPC measured and shall be paid separately). |
| 19 | M&L for 15 mm thick rendering in cement mortar (1:6) on fair faces of brick work, or concrete work rendering finished even and smooth (without using extra cement), complete all as specified and directed. |
| 20 | Supply only integral water proofing compond, all as specified and directed. |
| 21 | Taking down chowkhats or frame not exc 1.50 sqm each with shutter (without taking off shutters from the frame), complete all as specified and directed. |
| 22 | Taking down chowkhats or frames exc 1.5 sq. m but n exc 4 sq. m each with shutters (without taking off shutters from the frame), complete all as specified and directed. |
| 23 | Taking down shutters of any description exc 1 sq. m and n exc 2 sq. m each, complete all as specified and directed. |
| 24 | S&F of pressed steel frame of size 125 x 60mm for door with one or more rebates including necessary fixing, lugs, hinges, lock, strike plate, etc complete all as specified. |
| 25 | S & F 30mm thick flush shutters, solid core construction, with particle board core and plywood face panels commercial type on both sides Complete all as specified directed. |
| 26 | Dismantling boarding, any description, fixed in any position with nails, as cub boars self and partion complete all as specified and directed. |
| 27 | S&F of 18/19mm thick particle board, medium density, flat pressed, single layer type or three layer type with BWR type adhesive, fixed with screws to timber frame work, complete all as specified and directed. |
| 28 | S&F of 100mm size hasp and staple, mild steel, wire type, stove enamelled black, including bolt to hinge plate and fixed with screws, all as specified and directed. |
| 29 | S & F 40mm (width of flaps when open) continuous (piano) hinges, mild steel, bright finish or electrogalvanised, complete all as specified and directed. |
| 30 | S&F Ball catches with 8mm dia steel ball, and brass body and striking plate including letting in and fixed complete all as specified and directed. |
| 31 | S&F of 35 mm thick (batten thickness) second class hard wood, glazed and Skelton shutters, open rebated and prepared to receive glass, gauge, etc , divided into squares, with plain chamfered or rounded, mitred and rebated sash bars, edges of framing plain, chamfered or rounded with cut mitred beds for securing glass etc, supplied and fitted to chowkhats complete all as specified and directed.Note: The dimension of the various components or parts of shutters shall be as specified in clause 8.24 (a) of MES SSR 2009 Part I) |
| 32 | S&F of solid PVC door frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S. Square tube, suppling & fixing in opening as per specification & drawing, complete all as specified and directed. |
| 33 | S&F of factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, suppling & fixing in the frame at site as per specification & drawing and as directed. |
| 34 | S&F of steel windows with side hung shutters including projecting type hinges with steel handle, and steel peg stay, complete with glazing bars, dovetailed or welded, complete all as specified and directed. |
| 35 | S&F of steel windows with side hung shutters including projecting type hinges with steel handle, and steel peg stay, complete without glazing bars, dovetailed or welded, complete all as specified and directed. |
| 36 | S&F of 3.0mm thick sheet glass, ordinary quality and glazing with oil putty in square n exc 0.5 sq. m in each pane, complete all as specified and directed. |
| 37 | S&F in repairs galvanised mild steel wire cloth, 0.56mm nominal dia of wire and average width of aperture 1.18mm and fixed with tinned tacks, or galvanised wire staples, complete all as specified and directed. |
| 38 | S&F of 100 mm size butt hinges, medium weight, cold rolled mild steel and fixed, all as specified and directed. |
| 39 | S&F of 150 mm long aluminium, anodised, barrel tower bolt, of extruded section and fixed, all as specified and directed. |
| 40 | S&F of 150 mm size aluminium handles, cast type, anodised, all as specified and directed. |
| 41 | S&F of 250 mm long aluminium alloy, anodised sliding door bolts with haps staple (bolt type), and fixing clips of sheet, cast or extruted sections and fixing bolt and sliding bolts of extruted sections or cast aluminium alloy and fixed, complete all as specified and directed. |
| 42 | S&F of 140 mm long (overall length of cover plate) floor door stopper of aluminium alloy body and tongue, anodised, with hard drawn steel spring, fixed in floor, all as specified and directed. |
| 43 | S&F of mild steel framed work such as grills, gratings, etc. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe.290.Gde-E-165, complete all as specified and directed. |
| 44 | M&L for plain cement concrete (1:3:6), type C1 (using 20mm graded crushed stone aggregate) in lintels upto 1.5m clear span, cills, steps; seismic and other similar bands, plinth courses, string courses, lacing courses, parapets and railings upto 60 cm in height, copings, kneelers, apex stones, bed plates, kerbs, water troughs and the like including weathering, slightly rounded or chamfered angles and throating, complete all as specified and as directed. |
| 45 | S&F of 15 mm bore steel water tubes, medium grade, galvanised with and including all GI fitting (such as bends, elbows, Tees, connectors, short pieces, back nuts, unions, caps and plug etc ) and fixed complete to wall and ceiling or laid in/on floor, complete all as specified and directed. |
| 46 | S&F of 20 mm bore steel water tubes, medium grade, galvanised with and including all GI fitting (such as bends, elbows, Tees, connectors, short pieces, back nuts, unions, caps and plug etc ) and fixed complete to wall and ceiling or laid in/on floor, complete all as specified and directed. |
| 47 | M&L for cutting chases, pinning in. making good to facings where required and pointing in cement mortar (1:3) to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc.; and cutting chases for concealed water tubing or concealed conduit wiring, etc., and making good, cutting not exc 10 cm girth on stone walls, complete all as specified and directed. |
| 48 | S&F in repairs of 15mm bore dia bib taps, chromium plated, fancy type with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule and fixed, complete all as specified and directed. |
| 49 | S&F of 15mm bore dia pillar taps, cast copper alloy, with capstan heads, chromium plated, screwed down high pressure, with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly-nuts, screwed for iron pipe and fixed, all as specified and directed. |
| 50 | S&F in repair 15mm bore dia stop valves, chromium plated, fancy type, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed, complete all as specified and directed. |
| 51 | S&F in for sheet glass shelf assembly consisting of 5.5mm thick sheet glass shelf 12cm wide with chromium plated bracket guard and railing 60cm long, complete all as specified and directed. |
| 52 | S & F Vitrous China wash down water closet pan pedestal pattern white, inclusive of PVC seat cover white recess bottom type mild steel chromium plated or aluminium handing device and fixing 'P' or 'S' trap, connecting to union of flushing cistern and drain pipe complete all as specified and directed. |
| 53 | S&F in repair brass chromium plated tubular towel rail, 20mm dia, D type, 60cm long between flanges, complete all as specified and directed. |
| 54 | S&F of toilet paper holder, of brass chromium plated fixed to wall with chromium plated brass screws, all as specified and directed. |
| 55 | S&F in repair Soap dish, any type, fixed to plugs with chromium plated brass screws complete all as specified and directed. |
| 56 | S&F in repair Towel Ring CP fixed with and including Chromium plated brass screws and wooden/plastic cleats (Minimum weight 90gms) complete all as specified and directed. |
| 57 | S&F in repair health faucet (ABS Body) mild steel chromium plated suitable for 15 mm dia pipe with 1.25 metre long flexible tube and ABS wall hook including making connections and fixed in position complete in all respect, complete all as specified and directed |
| 58 | S&F of PVC low level flushing cistern 10 litre capacity, valveless syphonic action type complete with inlet, ball valve, float valve, bends brackets, rawl plug, brass screws handle etc complete having BIS description mark with IS:2731 with and including suitable size of MS brackets, plug, screw all as required incl taking down existing high level/low level flushing cistern any type disconnecting pipes and jointing with new one etc, and making good the floors/walls as per existing floor finish/wall finish including 32 mm bore PVC flush pipe and jointing with water closet of any type, complete all as specified and directed. |
| 59 | S & F sink made of stainless steel 1mm thick kitchen or laboratory with plugs, washers and waste pipe, waste coupling; including bedding in cement mortar on to dwarf wall or including fixing cantilever brackets and connecting union to pipe, overall size 495mm x 420mm bowl size 410mm x 330mm x 160mm, complete all as specified and directed. |
| 60 | S&F of 600mmx450mm bevelled edge mirror of selected quality glass, mounted on 6mm thick AC building board or commercial plywood and fixed to wooden plugs with chromium plated brass screws and cup washers, complete all as specified and directed. |
| 61 | S&F of vitreous china wash basin white of any pattern, flat back of size 550mm x 400mm (excluding taps), suitable size of brackets including pedestal and bracked, complete all as specified and directed. |
| 62 | S&F of PVC connections 15mm size with PTMT nuts of length 450mm, all as specified and directed. |
| 63 | &F of rotational moulded polyethylene water storage tanks of capacity 1000 litres (cylindrical vertical with closed top) hoisted and fixed in position including dismantling of exiting tank all as specified in SSR Part-l and directed. |
| 64 | Supplied and fixed in repair 20 mm bore gun-metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed, complete all as specified and directed. |
| 65 | M&L for 75 mm diameter (outlet) cast iron floor trap, with grating including jointing to waste pipe fixed in cement concrete type B-1 (1:2:4), complete all as specified and directed. |
| 66 | S&F in repairs of 25mm dia stain less curtain rod (curtain rails),chromiun plated curtain rod with fixing brackets stops roller etc., complete all as specified and directed. |
| 67 | M&L for complete removal of existing treatment of wall surfaces and applying two coats of Cement Base Paint of approved tint over a coat of chalk whiting priming paint complete all as specified |
| 68 | M&L for complete removal of existing treatment and applying three coats of white wash in ceiling, complete all as specified and directed. |
| 69 | M&L for preparation of new surface/undecorated surfaces of walls and applying two coats of Oil bound distemper over a coat of chalk whiting priming paint over 1mm thick wall care putty in two coats complete all as specified. |
| 70 | M&L for preparation of new surface/undecorated surfaces of walls and applying two coats of Cement Base Paint of approved tint over a coat of chalk whiting priming paint complete all as specified |
| 71 | M&L for preparation of new steel surfaces of any description over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide, zinc chrome primer, complete all as specified and directed. |
| 72 | M&L for preparation of old wood or wood based surfaces of any description over 10 cm width or girth not otherwise described and applying one coat of synthetic enamel paint, complete all as specified and directed. |
| 73 | Dismantling of plain or corrugated steel sheeting, any gauge, thickness, including Nainital or similar pattern roof coverings, complete all as specified and directed. |
| 74 | S&F of pre-painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws all as specified and directed. |
| 75 | S&F of pre-painted galvalume aluminum zinc coating GI based plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws all as specified and directed. |
| 76 | Dismantling of 75/100mm dia cast iron or reinforced concrete drain pipes, jointed in cement mortar and taking out of trenches, if required, complete all as specified and directed. |
| 77 | S&F of 110mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to walls, including taking down of old material as in repair complete all as specified and directed. |
| 78 | S & F PVC ( SWR ) bends 110 mm bore, complete all as specified and directed. |
| 79 | M&L for 75mm diameter of outlet PVC (SWR) floor trap, plain with grating including jointing with solvent cement, complete all as specified and directed. |
| 80 | S&F of 75 mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to walls, complete all as specified and directed. |
| 81 | S & F PVC ( SWR ) bends 75 mm bore, complete all as specified and directed. |
| 82 | Dismantling of wall and ceiling boards (fibre, pulp, insulation, etc.) or insulation boards/slabs/ blankets, any thickness, including cover fillets, complete all as specified and directed. |
| 83 | S & F for Anodised aliminium snap grid frame work for false ceiling confirming IS:733, 737 & IS:1285 ;Hangers 6 mm dia. G.I. (upto 1200mm length) adjusting level fixed to roof slabs by means of ceilling cleats made out of G.I. flat 40 x 3 mm size 60mm long and expansion hold fasteners 12.5mm dia. 40mm long complete all as specifiedI all as specified and as directed |
| 84 | M&L for preparation of new wooden or wood based surfaces of any description over 10 cm width or girth not otherwise described and applying two coats of synthetic enamel paint over a coat of pink primer, complete all as specified and directed. |
| 85 | M&L 4mm thick Non asbestos fibre cement building boards fixed or laid/ inserted to timber/Gt/Aluminium framework with screws complete all as specified and directed by Engr-in-charge. |
| 86 | Dismantling Structural steel work includings door, gates, etc and similar works complete all as directed |
| 87 | S&F of channel, angle, flat iron or Tee sections, bent to required shape, holes drilled as in cross bracings etc fixed independently with connecting plates including, etc confirming to Fe 410-W (Gde 250 quality A) complete all as specified and directed. (Note: The rate is inclusive of all necessary scaffolding, staging, access arrangements, and all other incidental works required for execution at any height. The work shall be carried out at multiple building locations.) |
| 88 | S & F mild steel work in tubular trusses, purlins including special shaped washer etc. compolete using ERW or induction butt welded tubes conforming to I.S 1161-1979 grade St. 240 as in frame work for sun shade, roof, projection etc. Complete all as specified and directed. |
| 89 | S&F Rolled mild steel work in plates (plain) channels, squares cut or notched (ordinary and counter sunk) forming holes, with riveted, bolted or welded attachment complete all as specified and directed. |
| 90 | Taking down carefully old unsv copper/aluminium point wiring (light, fan, socket or power) complete,including fixture and fittings such as switches, ceiling roses, pendants, regulators, sockets,sunken type box etc.and removing materials to store for keeping in safe custody for reuse at site or for taking credit and making good to disturbed surfaces of walls, floors etc with its original specification complete all as specified and directed by Engr-in-Charge. |
| 91 | Material and labour for concealed point wiring for the followings with 1.5 Sqmm single core, PVC FRLSH insulated unsheathed, multistranded copper conductor drawn through and including PVC rigid conduit (medium grade) including necessary accessories like bends, tees, PVC square and elbow etc fixed on wall/ceiling with 1.5 Sqmm PVC FRLSH insulated unsheathed multi stranded copper conductor cable as earth conitinuity (green in colour) connected to common earth dolly including connected modular items/fixture like modular metal flush box,base/cover plate for switch/sockets etc including making good all disturbed surfaces to match the existing complete all as specified and directed as below :- |
| 92 | One light/fan point controlled by one,one way switch. |
| 93 | One bell point controlled by one push button switch |
| 94 | One 3 Pin 5 Amps socket outlet point on independent Board |
| 95 | One 3 Pin 5 Amps socket outlet point on same board alongwith other suitable switchs. |
| 96 | All as per item No 91 above here-in-before but using 2.5 sqmm PVC FLS insulated copper condutor wire for connecting 15A socket on independent board complete all as specified/directed. |
| 97 | Supply and fixing of modular switch one way 6 amps 1 module 240 Volts incl taking down old unsv one complete all as specifed/directed. |
| 98 | Supply & fixing of modular type,1 module 16 Amps one way switch 240 Volt AC including taking down old unsv complete all as specified directed. |
| 99 | Supply & fixing of modular socket out let 2/3 pin 6 Amps combined 2 module 240 Volts incl taking down old unsv one complete all as specified / directed. |
| 100 | Supply & fixing of modular type, 2 module, 6/16 Amps combined socket 240 Volt AC including taking down old unsv complete all as specified / directed. |
| 101 | Supply and fixing of modular bell push 6 amps 1 module 240 volt complete all as specified . |
| 102 | Supply and fixing in repair of electric Bell ,240 volt single pole complete all as specified and directed. |
| 103 | Supply and fixing of ceiling rose surface PVC/Polycarbonate, 65x50 mm two to three terminals complete all as specified/directed. |
| 104 | Supply & fixing in repair Lamp holder, PVC/Polycarbonatetype with cord grip cap suitable forpendant fittings incl taking down old unsv one complete all as specifed/directed. |
| 105 | Supply and fixing step type fan regulator two module complete all as specified. |
| 106 | S&F in repair Surface and Wall mounted LED batten 20 watt 4ft long with Aluminum housing & integrated Electronic Driver with IP20 PF 0.90 total system Lumens 1050 Lumens 6500k CRI≥80 Operating Voltage range 140V -270V Complete all as specified and directed. |
| 107 | S&F in repair Surface and Wall mounted LED light fitting mirror type 10 watt,220 volt, 2 feet Complete all as specified and directed. |
| 108 | S&F LED light fitting 25 Watt luminaires including LED light driver holder connecting up with three core flexible copper conductor cable suitable size IP66, Efficacy> 120 Lm/W ,complete all as specified. |
| 109 | Supply and fixing in repair of round shape 15 watt 220 volts AC recessed type with high efficiency PMMA diffuser soft glare free light complete with drivers, holders,LED lamp suitable for roof ceiling including connecting up with three core flexible copper conductor cable of suitable size complete Incl taking down old unsv one. |
| 110 | Supply and fixing in repair of MCB TPN DB 4 way double door,IP-43 protection,isolated neutral bar,insulated busbar assembly,mechanical impact strength of IK08 complete all as specified and directed by Engr-in-charge. |
| 111 | Supply and fixing in repair of MCB TPN 63 Amps 'C' series 10kA 415 volts complete all as specified and diretced. |
| 112 | Supply and fixing in repair of MCB SPN DB 8 way double door,IP-43 protection,isolated neutral bar,insulated busbar assembly,mechanical impact strength of IK08 complete all as specified and directed by Engr-in-charge. |
| 113 | Supply and fixing in repair of MCB SPN DB 4 way double door,IP-43 protection,isolated neutral bar,insulated busbar assembly,mechanical impact strength of IK08 complete all as specified and directed by Engr-in-charge. |
| 114 | Supply and fixing in repair of MCB SPN 32/40 Amps 'C' series 10kA 240 volts complete all as specified and diretced. |
| 115 | Supply and fixing in repair of MCB SP 6-32 Amps 'C' series 10kA 240 volts complete all as specified and diretced. |
| 116 | Single Pole and neutral enclosure with a two pin and earth plug and socket complete with one Double pole MCB. |
| 117 | Material & labour for Sub main wiring with two runs of single core 4 Sqmm (Nominal Area) FRLSH PVC insulated and unsheathed multi standed copper conductor cable LT 1100 volts grade drawn thorugh and including PVC concealed conduit medium grade of adequate size fixed on surface of wall/ceiling with all necessary fittings and accessories and 1 run of FRLSH PVC insulated and unsheathed insulated single core cable with multi standered copper conductor of size 4 Sqmm as earth wire (green in colour) run through PVC concealed conduit and connected common earth dolly including taking out the old sub main wiring for connection to DBs/dolly shall be deemed to be included in this item and shall be measured as one run complete all as specified and directed. |
| 118 | Material & labour for Sub main wiring with two runs of single core 6 Sqmm (Nominal Area) FRLSH PVC insulated and unsheathed multi standed copper conductor cable LT 1100 volts grade drawn thorugh and including PVC concealed conduit medium grade of adequate size fixed on surface of wall/ceiling with all necessary fittings and accessories and 1 run of FRLSH PVC insulated and unsheathed insulated single core cable with multi standered copper conductor of size 4 Sqmm as earth wire (green in colour) run through PVC concealed conduit and connected common earth dolly including taking out the old sub main wiring for connection to DBs/dolly shall be deemed to be included in this item and shall be measured as one run complete all as specified and directed. |
| 119 | M&L for painting of ceiling fan any type/size after taking down complete in situ with synthetic enamel paint by spraying incl filling cavities with fillier, one coat after cleaning all dust etc and refixing the fan to its original postioning incl providing suitable size clamp & down rods for hanging and connecting up including provision of cable from ceiling rose or connector to fan complete all as specified & directed. |
| 120 | Supply,laying connecting and testing XLPE insulated,PVC sheathed armoured LT electric power UG cable (heavy duty), aluminum stranded conductor 1.1KV grade, suitable for 3.5/4 core size laid through duct/pipe/in trench etc connected to LT panel/poles with cable gland &lugs incl taking down old unsv complete all as specified and directed. (Note:Excavation and earth work will be measured & paid separatly). |
| 121 | 95 Sqmm 3 1/2 core |
| 122 | 25 Sqmm 4 core |
| 123 | 10 Sqmm 4 core |
| 124 | Excavation in trenches in soft/loose soil not exceeding 1.5 mtr deep and not exceeding 1.5 mtr wide for laying of cable and erection of poles all as specified and directed. |
| 125 | Returning filling in including spreding,leveling,watering and well ramming excavated soft/loose soil in layers, all as specified and directed at site. |
| 126 | Removing excavated material not exceeding 50 m and depositing at a level not exceeding 1.5 m above the starting point all as specified and directed by engineer -in- charge. |
| 127 | M&L for sand cushioning to under ground cable using locally available fine clean dry river sand over under ground UG cable laid in trenches and gently punning to cushioning to cable complete all as specified and directed by Engineer-en-ChargeNote : For the purpose of payment only punned thickness will be measured. |
| 128 | M&L for brick protection cover of size 230x115x75mm to LT underground cables with sub class 'B' over brunt brick,(Locally available best quality),laid dry and flat abutting each other with gaps not exceeding 10mm complete all as specified and directed . |
| 129 | Boring/Drilling (horizontally) manually under .5 to 2 m deep in soil below existing road suitable for passing GI tubing of 40 mm bore complete all as specified. |
| 130 | Supply and fixing in repair of GI tubing light grade 40mm dia for protection of cable on pole ,under road crossing or acroos drain,along electric pole or floor/wall complete all as specified and directed . |
| 131 | Dismantling and taking down old unserviceable LT panel board and Supply, installation, testing and commissioning of Panel board not less than 1.5m x 1.2 m x0.8m outdoor cubical type factory made (CPR) approved) double door, front & back both side openable type fixed with Butt Hinges and locking arrangement with Aldrop latches.fabncated of CRCA sheet inner sheet 2.0 mm thick hinged type door for individual MCCBs and outer door 3.15 mb thick, rubberised gasket, supported on 50x 50 x 6 mm angle iron and Tee section frame dust and vermin proof complete with aluminium bus bar 4 Nos 600 Amps rated capacity mounted on porcelain insulators totally enclosed chamber for protection 3 phase 415 voll with suitable capacity alumimum bus bar/ PVC insulated copper cable control wining duly mounted on PCC foundation with suitable size of bolts, nuts & wansers and connecting all CA OG existing cables Panel board, shall be powder coated and angle iron frame painted with black synthetic enamel pant over a coat of red oxide primer complete connecting existing cables with suitable size glands and lugs to accommodate and including the following:- |
| 132 | INCOMING:-(a) Aluminium busbar 375 Amps rated capacity-04 Nos(b) MCCB 250 Amps, 4 pole. 415 volt, 36 KA thermal &magnetic release adjestable type-01 No(c) Spreader Link -01 Sets |
| 133 | OUTGOING:(a) MCCB 63 Amps, 4 pole, 415 volt 16 kA thermal & magnetic release adjestable type-4 Nos(b) Spreader Link -04 Sets(c)LED multifunction meter-01 No(d)Phase indicator lamp (RYB) Set of three-01 Set(e)Aluminium bus bar 4 strip(f)Danger Notice plate-01 No(g)Panel control wiring complete with suitable size suitable size copper wire -01 job |
| 134 | Earthing complete with galvanized steel earth plate electrode 600 mm x 600 mm x 60 mm thick buried directly in ground (earth pit not less than 2.25 meter deep below ground level) with top edge of plate not less than 1.5 meter below normal ground level, connected to galvanized earth lead wire 4 mm dia by means of bolts, nuts, check nuts and washers of galvanized iron or steel, all as shown in Electrical Plate No 3 of SSR Part - I, including necessary excavation and earth work, P.C.C (1:3:6) type C-I with 50 mm thick Pre-cast R.C.C. (1:2:4) type B-I cover slab (reinforced with 8 mm dia deformed bar @ 15 cm C/C both ways and suitable handle of 10 mm dia round bar), including providing charcoal or coke and common salt in alternate layers of 15 cm compacted thickness all around the earth electrode, with funnel and 20 mm bore galvanized iron watering pipe (light grade), wire mesh, aluminium lugs, complete in all respect, GI earth wire protected by 15 mm bore (medium grade) galvanized iron pipe and other end connected with main switch board or Earthing test point as directed, including necessary earth work and disposal of spoil to a distance not exceeding 50 metre and necessary testing on completion including dismantaling old unsv ones complete all as specified and as directed by the Engineer-in-Charge. |
| 135 | Earthing complete with galvanized steel earth plate electrode 600 mm x 600 mm x 60 mm thick buried directly in ground (earth pit not less than 2.25 meter deep below ground level) with top edge of plate not less than 1.5 meter below normal ground level, connected to galvanized iron strip of size 25x4 mm by means of bolts, nuts, check nuts and washers of galvanized iron or steel, all as shown in Electrical Plate No 3 of SSR Part - I, including necessary excavation and earth work, P.C.C (1:3:6) type C-I with 50 mm thick Pre-cast R.C.C. (1:2:4) type B-I cover slab (reinforced with 8 mm dia deformed bar @ 15 cm C/C both ways and suitable handle of 10 mm dia round bar), including providing charcoal or coke and common salt in alternate layers of 15 cm compacted thickness all around the earth electrode, with funnel and 20 mm bore galvanized iron watering pipe (light grade), wire mesh, aluminium lugs, complete in all respect, GI earth wire protected by 15 mm bore (medium grade) galvanized iron pipe and other end connected with main switch board or Earthing test point as directed, including necessary earth work and disposal of spoil to a distance not exceeding 50 metre and necessary testing on completion including dismantaling old unsv ones complete all as specified and as directed by the Engineer-in-Charge. |
| 136 | Note 1:- (Applicable for all parts/items) : The bidders/contractors are advised to read tender document, all drawings & all corrigendum / amendments and general condition of contracts before entry / quoting the rates.Note 2:-The contract sum shall be arrived at after deducting amount of schedule of credit from the total quoted amount. Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Sep 28, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedOct 28, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 22 daysOct 29, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 23 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender