Tender For Comprehensive Repair And Maintenance To E/M Installations Under Ge Bhopal
Tender Value
40 Lakhs
Estimated cost
Bid Submission
19 Oct 2026
3 days left
EMD
80000
Bank guarantee accepted
Document Fee
500
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Bhopal → Madhya Pradesh
EMD Exemption
Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for Comprehensive Repair And Maintenance To E/M Installations Under Ge Bhopal
Corrigendum
| Sr No | Corrigendum Date | Corrigendum | Type | New Submission Date |
|---|---|---|---|---|
| 1 | 09-Oct-2026 | certain amendment in BOQ | BOQ | 19-Oct-2026 |
BOQ
| Sl. No. | Item Description |
| 1 | Note :(i) Please refer Sch A/ BOQ Notes before quoting the tender for all phases/ items mentioned below.(ii) Amount of Schedule of credit shall be deducted offline |
| 2 | M&L for cement concrete 1:4:8 type D-2 (using 40 mm graded stone aggregate) as in sub base concrete including demolition of concrete and paving n.exc 15cm thick (below or above GL) complete all as specified and directed. |
| 3 | M & L for 25mm thick PCC 1:2:4 type B-1 as in levelling course complete all as specified and directed. |
| 4 | M&L for heavy duty light shade anti-skid outdoor tiles of 10 mm thick (square/rectangular) area of each tiles exc .18 sqm but not exceeding .36 Sqm as in floor, providing durability, low porosity for extra wear, etc. set and jointed and pointed in chemical resistant mortar, resin type, in floors complete including Demolition all as specified and directed. |
| 5 | M&L for hard core of broken stone of gauge not exceeding 63 mm, deposited, spread & levelled in layers not exceeding 15 cm thick watered and rammed to a true surfaces complete all as specified and directed. |
| 6 | Taking out settled bricks/ interlocking paver blocks any thickness (laid flat or on edge) in path, floors, channels, kerbs, aprons, etc. (each layer) laid dry and refixing at same location over and including 50mm sand cushioing all as specified and directed. |
| 7 | S&F providing and laying 60mm thick rubber moulded factory made chamfered edge cement concrete glossy finish paver block of M-35 grade with approved colour, design & pattern as in footparth, parks, lawns, drive ways or light traffic parking etc., of required strength, thickness & size/ shape, laid in required colour & pattern over and including 50mm thick compacted bed of fine sand, compacting and proper embedding/ laying of inter locking paver blocks into the sand bedding layer and filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand, complete all as specified and directed. |
| 8 | S&F Providing and laying 80mm thick rubber moulded factory made chamfered edge cement concrete glossy finish paver block of M-35 grade with approved colour, design & pattern as in footparth, parks, lawns, drive ways or light traffic parking etc., of required strength, thickness & size/ shape, laid in required colour & pattern over and including 50mm thick compacted bed of fine sand, compacting and proper embedding/ laying of inter locking paver blocks into the sand bedding layer and filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand, complete all as specified and directed. |
| 9 | M&L for chequered cement concrete tiles 30cm x 30cm x 23-25mm thick, set, jointed and pointed in neat cement slurry in floors including 20mm thick screed bed of CM 1:4 all as specified and directed. |
| 10 | M&L for cement concrete Type B-1, 1:2:4 (using 20 mm graded stone aggregate) as in bed blocks, copings, kneelers, apex stones, bed plates, lintels and the like etc complete all as specified and directed. |
| 11 | M&L cement concrete (1:3:6) type C-1 using (20mm graded stone aggregate) 75mm thick as in plinth protection/path etc finished fair and even laid in bays n.exc 2m in length and cutting of dummy joints 65mm deep x 10mm wide @ 3m intervals and at corners filled with bitumen mastic 1:3 complete all as specified and directed. |
| 12 | Dismantling posts or struts (wood, steel or RCC) any section embedded in concrete, masonry, brick work, incl taking out embedded portion and making good disturbed ground complete all as specified and directed. |
| 13 | S&F for mild steel works as in posts and struts in fencing including cutting tops to shape as directed, drilling holes, notching for wire etc and flat iron fillets for securing wire mesh similar work Confirming to Fe-290 Gde E-165 etc all as specified and directed. |
| 14 | Excavating in post holes in any type of soil (or similar holes) each n exc 0.5 cum, getting out, returning, filling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25 cm, incl removing of surplus soil complete all as specified and directed. |
| 15 | M&L Plain cement concrete (1:3:6) type C2 (using 40 mm graded stone aggregate) as in foundations / mass concrete complete all as specified and directed. |
| 16 | Dismantling fencing wire mesh , any type complete all as specified and directed. |
| 17 | S&F PVC coated GI chain linck fencing 50x50mm, wire dia 2.4 to 4mm, 60 GSM including provn of binding wire. complete all as specified and directed. |
| 18 | S&F mild steel round bars 10 mm dia and over cut to length bent to shape required and all as specified conforming to gde Fe 410- W (Gde E-250) quality A for securing chain link fencing complete all as specified and directed. |
| 19 | M&L for Brickwork with fly ash bricks, straight or curved on plan exc 6m mean radius, built in, built in CM 1:6 including demolition of brick or stone work, built in cement mortar including all quoins, arches, pillars etc complete all as specified and directed. |
| 20 | Excavation in trenches not exceeding 1.5 m wide and not exceeding 1.5 m in depth; for foundations etc. or for shafts, well cess pits, manholes, pier holes, etc. but not exceeding 10 Sqm on plan and not exceeding 1.5 m in depth and getting out in any type of soil complete all as specified and directed. |
| 21 | M&L for moorum in returning, filling in, including spreading, levelling, watering and well ramming in layer not exceeding 25 cm thick complete all as specified and directed. |
| 22 | Removing surplus soil obtained from excavation to a distance not exceeding 50 metre and depositing where directed at a level not exceeding 1.5 metre above the starting paint complete all as specified and directed. |
| 23 | M&L Mild steel TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed. |
| 24 | M&L for use and waste formwork to sides of concrete foundation , footing, base of column , raft, raft beam sides and soffits of foundation and, walls, plinth beam for rough finished surfaces of concrete complete all as specified and directed. |
| 25 | M&L for reinforced cement concrete (nominal mix) type B1 1:2:4 (using 20mm graded aggregate) on as in slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves, chajjas and the like including demolition of cement concrete reinforced (reinforcement cut as required to facilitate demolition) in any description and in any position not other wise specifically provided for complete all as specified and directed. |
| 26 | M & L for 18mm thick granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, win dow-cills, cooking plat forms and like in cement mortar (1:4) including point ing in white cement (1:2) us ing marble dust with admix ture of pigment to match with shade of granite, complete all as specified and directed. |
| 27 | Dismantling of wrought iron or mild steel work of any description not otherwise provided for complete all as specified and directed. |
| 28 | M&L for steel gate, including pintle hinges, stops, hand-made sliding bolts, etc. framed work, forged into spikes; framed guard bars; barred iron doors; and drilled for fixing of steel sheeting or other covering similar work conforming to Fe.290.Gde-E-165 complete all as specified and directed. |
| 29 | S&F steel work in tubular trusses including special shaped washer etc. complete using ERW or induction butt welded tubes conforming to IS.11611979 grade St.-24 complete all as specified and directed. |
| 30 | M&L for preparation of new or previously untreated surfaces of steel and iron surfaces of any description, not otherwise described, over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of zinc chrome primer, complete all as specified and directed. |
| 31 | S&F for stainless steel wire cloth. 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples to UPVC door with beading complete all as specified and directed. |
| 32 | M&L pre galvalume aluminium zinc coating GI based corrugated steel sheet 0.50 mm thick AZ-150 of an colour having tensil strength of 550/MPA as in roof covering/cladding to wall/ ridge,fixed with self tapping screw/L type or J type cranked hook bolts including dismantling plain or corrugated steel sheeting,any gauge, thickness, including Nainital or similar pattern roof coverings/wall cladding all as specified and directed. |
| 33 | M&L pre-painted galvalume aluminum zinc coating GI based Plain steel sheet 0.50mm thick AZ-150 of any colour having tensile strength of 550 Mpa as in roof covering/cladding towall, fixed with self tapping screws including dismantling plain or corrugated steel sheeting,any gauge, thickness, including Nainital or similar pattern roof coverings/wall cladding all as specified and directed. |
| 34 | M&L for 15mm thick rendering in CM 1:4 faces of brick or concrete surfaces (External surfaces) finished fair, even and smooth without using any extra cement including taking down cement plaster on brick or stone wall etc including raking out joints, hacking for key, scrubbing down with water or cement lime plaster any description, complete all as specified and directed. |
| 35 | M&L for 15mm thick rendering in CM 1:4 faces of new brick or concrete surfaces (External surfaces) mixed with water proofing compound finished fair, even and smooth without using any extra cement complete all as specified and directed. Note :- Water Proofing compound shall be measured and paid seperately. |
| 36 | M&L for 10mm thick rendereing brick or concrete surface in CM 1:6 finishing the surface fair & even without using extra cement including taking down cement plaster on brick or stone wall etc including raking out joints, hacking for key, scrubbing down with water or cement lime plaster any description, complete all as specified and directed. |
| 37 | M&L for 10mm thick rendering in cement mortar 1:3 on concrete surfaces as in ceiling including finishing the surfaces even and smooth without using extra cement including taking down cement plaster on brick or stone wall etc including raking out joints, hacking for key, scrubbing down with water or cement lime plaster any description, complete all as specified and directed. |
| 38 | Integral water profing compound mixed with cement mortar complete all as specified and directed. |
| 39 | M&L for applying one coat of white wall putty 1mm thick on walls complete all as specified and directed. |
| 40 | M&L for preparation of newly plastered or unplastered surfaces of walls and applying two coats of oil bound distemper complete all as specified and directed. |
| 41 | M&L for preparation of newly plastered or unplastered surfaces in walls soffits, facia, chajjas and applying two coat of exterior weather proof water based emulsion (100% acrylic) over a coat of compatible primer, complete all as specified and directed. |
| 42 | M&L for Preparation of old decorated surfaces of walls and applying two coats of exterior weather proof water based emulsion paint (100% acrylic) all as specified and directed. |
| 43 | All as per item 41.00 here-in before but one coat of exterior weather proof emulsion paint on old prepared wall surfaces including chajjas, patta etc. surfaces, complete all as specified and directed. |
| 44 | M&L for complete removal of existing treatment on walls and applying 1 coat of wall care white putty 2mm thick and applying 2 coats of oil bound distemper including a coat of compatible wall primer, complete all as specified and as directed. |
| 45 | M&L for 10mm thick cement plaster over PCC in CM 1:3 finished even and smooth (without using extra cement) and using WPC of approved make as per manufacturers instruction from roof (G+2) or similar all as specified and directed. Note:- WPC shall be measured and paid separately. |
| 46 | M&L for priming surfaces with applying evenly a tack coat of hot industrial bitumen VG-10 grade at the rate of 1.2 kg per sqm including cleaning of newly plastered surface complete all as specified and directed. |
| 47 | M&L for applying APP based polymeric membrane minimum weighing 3kg/sqm and minimum 3mm thick reinforced with polyster non woven fabric (weight not less than 150 gms/sqm) laid on primed surface by fire torching with forced application including taking down old APP sheet of any thickness, complete all as specified and directed. |
| 48 | M&L for preparation of newly fixed APP surfaces and evenly applying with roller brush two coat of aluminum paint all as specified and directed. |
| 49 | M&L for preparing and applying Dr. Fixit rain coat on external walls in following steps as appended below:-(1) Existing substrates cleaned and removed all scale dirt, algea moss, fungal growth using mechanical vaccum wall sander (having RPM not less than 1500) sanding pad of 80 grit of dia 7\\"/ 9\\"on walls (external surface) . All norrow cracks upto 5mm shall be repaired with crack X-paste and the larger cracks upto 10mm with Dr fixit crack-X shrink free. The surface shall be made dry completely for upto 4-6 days for application of primer.(2)Applying one coat primer Dr. Fixit rain coat diluted with 2:1 with water (chemical:water) maintaining spreading rate @ 8 to 10 sqm / ltr. (3) Applying two coats of Dr Fixit raincoat without any dilution for coverage 3.5 sqm/ltr and second coat of Dr. fixit rain coat without any dilution for coverage 7 sqm/ltr complete all as specified and directed.Note :- (i) Second coat must be applied after lapse of 6 to 8 hours application of first coat.(ii) The application of Dr Fixit raincoat must be avoided at temperature below 10˚C more than 35˚C and in direct sunlight. |
| 50 | M & L for fabricating and fixing powder coated (Minimum 50 miciron ) aluminium sections of required size for doors, windows any type, frames and partitions including aluminium hinges of required size jointing cleats, screws salsh fasterners , plug for fixing with walls, column etc including taking down damage portion of damage door, windows or taking down complete door/ window complete all as specified and directed. (Make- Jindal/Ajit India/HindlcoNote :- Rates are inclusive of necessary new fitting for door/ window i.e handle, tower bolt, butt hinges, rubber beadings etc complete. |
| 51 | M&L framed work such as grills, gratings, gate etc with ends of bars souldered and/or riveted or forged into spikes, framed guard bars, barred iron doors, ladders, framed balusters, walkways, railing, frame work of water tanks and similar work conforming to Fe-290, Gde E-165 complete all as specified and directed. |
| 52 | S&F 4.00 mm thick plain glass and glazing with putty /uPVC beading including rubber packing, fixing glass to UPVC surrounds complete all as specified and directed. |
| 53 | S&F for stainless steel wire cloth. 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples to aluminium window/ wooden doors etc with beading complete all as specified and directed. |
| 54 | M/L for non skid ceramic coloured tiles 7mm to 8 mm thick (square /rectangular) area of each tile exceeding 0.11 Sqm, but not exceeding 0.18 Sqm, in floors over and including 15mm thick screed in CM 1:6 etc set and jointed in neat cement slurry and pointed in white or coloured cement to match the shades of tiles including dismantling floor, hearth or wall tiling including cement mortar bedding(but not backing), removing serviceable tiles and rubbish off the permises complete all as specified and directed. |
| 55 | M&L for coloured glazed ceramic tiles of size 450mm X 300mm X 7mm thick in vertical surface, set and jointed over and including 10 mm thick rendering even and rough in CM1:4 for backing of tiles, jointed in neat cement slurry and pointed in white or colour cement to match the shade of tiles including dismantling floor, hearth or wall tiling including cement mortar bedding(but not backing), removing serviceable tiles and rubbish off the permises, complete all as specified. |
| 56 | M&L for Light shade vitrified ceramic tiles (of approved shade and design) area of each tiles not exc 0.36sqm, as in floors and skirtng, etc. set and jointed in neat cement slurry and pointed with white cement including 15mm thick screed bed in CM (1:6) including dismantling of old tiling fixed in any mortar complete all as specified and as directed. |
| 57 | M&L machine cut cut kota stone slab flooring 18-20 mm thick over cement screed base laid & jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing & polishing complete over 15mm thick screed bed in cement mortar 1:6 including dismantling of stone slabs and tiles of any description or thickness in floors, aprons, walls, etc, laid bedded and pointed in any mortar, complete all as specified and directed. |
| 58 | All as per item 56.00 here-in before but in skiring over 10mm thick rendering in cm 1:4 including dismantling of stone slabs and tiles of any description or thickness in floors, aprons, walls, etc, laid bedded and pointed in any mortar complete all as specified and directed. |
| 59 | S&F galvanised cold rolled steel section framed work size 600x600mm grid size 24x38x0.30 mm Tee (bottom precoated) and 24x24x0.30 mm thick wall angle galvanised cold rolled steel section including expansions fasteners as in ceiling, complete all as specified and directed. Make : Gabson or equivalent as approved by GE. |
| 60 | S&F 6mm thick exposed metal frame ceiling with PVC coated panels in ceiling of approved design by Engr-in-Charge PVC material having a minimum density of 600kg/m3. The panel dimension will be 600 mm x 600mm for fixing in 600 mm x 600mm grid (Frame work for ceiling shall be measured and paid separately) complete all as specified and directed. |
| 61 | Taking down chowkhats or frame with shutter n.exc 1.5 sqm each with shutters (without taking off shutters from the frame) complete all as specified and directed. |
| 62 | Taking down chowkats or frames with shutters (without taking off shutters from the frames) exc. 1.5 sq. m but not exc 4 sq. m each complete all as specified and directed. |
| 63 | S&F factory made single extruded WPC (Wood Polymer Composite) solid plain flush door shutter of 30mm size comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, all as per direction of Engineer-In-Charge. and including supply and fixing following items As approved by Engr-In-Charge : (a) Stainless Steel (304 Grade) Finished Butt HinAGEs 125mm - 3 Nos per leaf(b) Stainless Steel (304 Grade) Finished Tower Bolt 200mm long - 2 Nos per leaf(c) Stainless Steel (304 Grade) Finished Handles 200 mm - 2 Nos per leafMaterial test certificate and authentication should be compulsory provided by the manufacturing company : For Internal/Balcony/Main Doors. |
| 64 | S&F factory made single extruded WPC (Wood Polymer Composite) solid door/ window/Ceosetory windows & other Frames/Chowkhat of size 65x100 mm comprisingof virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed stainless steel screws having minimum frame density of 750 kg/cum, screw withdrawal strength of 2200 N(Face) & 1100 N (Edge), minimum comp ressive strength of 58 N/mm2 modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire retardantand fixed in position with MS hold fast/lugs/SS dash fasteners of required dia and length complete as per direction of Engineer-in-Charge. (M.S. hold fast/ lugsor SS dash fasteners shall be paid forseparately). Note: For WPC solid door/window frames,minus 5mm tolerance in dimension i.e. depth and width of profile shall beacceptable. Variation in profile dimensionson plus side shall be acceptable but no extra payment on this account shall be made. |
| 65 | S&F wire netting of glavanised steel wire 1.40mm dia and 25mm size of mesh fixed with tinned tacks of wire staples with complete all as specified and directed. |
| 66 | M/L grouting with cement mortar with mechanical pressure through nozzles HD PVC 10 CM long 25mm dia to stop cracks /leakage sand seepage from wall floor nozzles shall be fixed at 1 mt c/c in stagered manner and mortor (CM 1:1) mixed with WPC shall be filled with pressure to stop leakage (seepage in croaks, concret, walls or floor) till rejection finishing the nozzles by concrete mix with appoxy after treatment including taking down plaster complete all as specified and directed. |
| 67 | Deduct Schedule of credit (calculation will be done off line) Rs. 32550.00 Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Oct 09, 2026
11:30 IST
Tender Published
Tender notice published.
Completed
Oct 19, 2026
18:00 IST
Corrigendum-1 Issued
Clarifications on tender conditions and amendments issued.
Upcoming · 3 daysOct 19, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 3 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender