Tender For Widening And Strengthening Of The Atrauli-Palimukimpur Odr Road From Chainage 0.000 To 9.700 In Aligarh District Under The Pandit Deendayal Upadhyaya Yojana For The 2026-27 Financial Year
Tender Value
16.60 Crore
Estimated cost
Bid Submission
24 Oct 2026
22 days left
EMD
30 Lakhs
Bank guarantee accepted
Document Fee
2354
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Aligarh → Uttar Pradesh
EMD Exemption
Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for Widening And Strengthening Of The Atrauli-Palimukimpur Odr Road From Chainage 0.000 To 9.700 In Aligarh District Under The Pandit Deendayal Upadhyaya Yojana For The 2026-27 Financial Year
BOQ
| Sl. No. | Item Description |
| 1 | Excavation for roadwork in soil with hydraulic excavator including cutting and loading in tippers, trimming bottom and side slopes, in accordance with requirements of lines, grades and cross sections, and transporting to the embankment location within all lifts and lead upto 1000m & including cost of all material, labour, T&P, labour cess and all other taxes but excluding G.S.T. |
| 2 | Construction of embankment with approved materials deposited at site from roadway cutting and excavation from drain and foundation of other structures graded and compacted to meet requirement of Table 300-2 (Compacted) As per Mort&h clause 305 S.No.3.17 & including cost of all material, labour, T&P, labour cess and all other taxes but excluding G.S.T. |
| 3 | Construction of embankment with approved material obtained from borrow pits with all lifts and leads, transporting to site, spreading, grading to required slope and compacting to meet requirement of table 300-2.As per MORT&H clause 3.16(305) & including cost of all material, labour, T&P, labour cess and all other taxes but excluding G.S.T. |
| 4 | Construction of granular sub-base by providing close graded material, spreading in uniform layers with motor grader on prepared surface, mixing by mix in place method with front end loader at OMC, and compacting with vibratory roller to achieve the desired density, complete as per clause 401 & including cost of all material, labour, T&P,Royalty, ISTP, labour cess and all other taxes but excluding G.S.T.) |
| 5 | Providing, laying, spreading and compacting graded stone aggregate to wet mix macadam specification including premixing the Material with water at OMC in mechanical mix plant carriage of mixed Material by tipper to site, laying in uniform layers with grader in sub- base / base course on well prepared surface and compacting with vibratory roller to achieve the desired density & including cost of all material, labour, T&P,Royalty, ISTP, labour cess and all other taxes but excluding G.S.T.) |
| 6 | Providing and applying primer coat with SS2 grade bitumen emulsion on prepared surface of granular Base including clearing of road surface and spraying primer at the rate of 0.70 kg/sqm using mechanical means & including cost of all material, labour, T&P, labour cess and all other taxes but excluding G.S.T. |
| 7 | Providing and applying tack coat with bitumen VG-10 using emulsion pressure distributor at the rate of 0.30 kg per sqm on the prepared bituminous surface cleaned with mechanical broom. Clause 503 & including cost of all material, labour, T&P, labour cess and all other taxes but excluding G.S.T. |
| 8 | Providing and applying tack coat with bitumen emulsion using emulsion pressure distributor at the rate of 0.25 kg per sqm on the prepared bituminous surface cleaned with mechanical broom & including cost of all material, labour, T&P, labour cess and all other taxes but excluding G.S.T. |
| 9 | Providing and laying dense graded bituminous macadam (Grade-I) with higher capacity batch type HMP using crushed aggregates of specified grading, premixed with bituminous binder @ 4.0 percent by weight of total mix and filler, transporting the hot mix to work site, laying with a hydrostatic paver finisher with sensor control to the required grade, level and alignment, rolling with smooth wheeled, vibratory and tandem rollers to achieve the desired compaction as per MoRT&H specification clause No. 505 complete in all respects & including cost of all material, labour, T&P,Royalty, ISTP, labour cess and all other taxes but excluding G.S.T.) |
| 10 | Providing and laying dense graded bituminous macadam (Grade-II) with higher capacity batch type HMP using crushed aggregates of specified grading, premixed with bituminous binder @ 4.5 per cent by weight of total mix and filler, transporting the hot mix to work site, laying with a hydrostatic paver finisher with sensor control to the required grade, level and alignment, rolling with smooth wheeled, vibratory and tandem rollers to achieve the desired compaction as per MoRTH specification clause No. 505 complete in all respects & including cost of all material, labour, T&P,Royalty, ISTP, labour cess and all other taxes but excluding G.S.T.) |
| 11 | Providing and laying of a stress absorbing membrane over a cracked road surface, with crack width below 6 mm after cleaning with a mechanical broom, using modified binder complying with IRC:SP: 53, sprayed at the rate of 11 kg per 10 sqm and spreading 5.6 mm crushed stone aggregates @ 0.11 cum per 10 sqm with hydraulic chip spreader, sweeping the surface for uniform spread of aggregates and surface finished to conform to clause 902 & including cost of all material, labour, T&P,Royalty, ISTP, labour cess and all other taxes but excluding G.S.T.) |
| 12 | Providing and laying bituminous concrete with higher capacity batch type hot mix plant using crushed aggregates of specified grading, premixed with bituminous binder (VG-30) @ 5.4 per cent of mix and filler, transporting the hot mix to work site, laying with a hydrostatic paver finisher with sensor control to the required grade, level and alignment, rolling with smooth wheeled, vibratory and tandem rollers to achieve the desired compaction as per MORTH specification clause No. 507 complete in all respects & including cost of all material, labour, T&P,Royalty, ISTP, labour cess and all other taxes but excluding G.S.T.) |
| 13 | Construction of sub-grade and earthen shoulders with approved material obtained from borrow pits with all lifts & leads, transporting to site, spreading, grading to required slope and compacted to meet requirement of table No. 300-2 (Local Earth) & including cost of all material, labour, T&P, labour cess and all other taxes but excluding G.S.T. |
| 14 | Construction of sub-grade and earthen shoulders with approved material obtained from borrow pits with all lifts & leads, transporting to site, spreading, grading to required slope and compacted to meet requirement of table No. 300-2 Carted earth 2 km & including cost of all material, labour, T&P, labour cess and all other taxes but excluding G.S.T. |
| 15 | Earth work in excavation of foundation of structures as per drawing and technical specification, including setting out, construction of shoring and bracing, removal of stumps and other deleterious matter, dressing of sides and bottom, backfilling the excavated portion.Depth up to 3.0m & including cost of all material, labour, T&P, labour cess and all other taxes but excluding G.S.T. |
| 16 | Plain cement concrete 1:3:6 nominal mix in foundation with crushed stone aggregate 40 mm nominal size mechanically mixed, placed in foundation and compacted by vibration including curing for 14 days (MoRTH Sl.No. 12.04) & including cost of all material, labour, T&P,Royalty, ISTP, labour cess and all other taxes but excluding G.S.T.) |
| 17 | Plain/Reinforced Cement Concrete in Open Foundation complete as per Drawing and Technical Specifications. RCC Grade M20 & including cost of all material, labour, T&P,Royalty, ISTP, labour cess and all other taxes but excluding G.S.T.) |
| 18 | Supplying, Fitting and Placing un-coated HYSD bar Reinforcement in Foundation complete as per Drawing and Technical Specifications. As per Morth Sr.No.9.07 & including cost of all material, labour, T&P, labour cess and all other taxes but excluding G.S.T. |
| 19 | Kilometre Stone Reinforced cement concrete M15grade kilometre stone of standard design as per IRC:8, fixing in position including painting and printing etc.As per MORT&H clause 8.14 (804) & including cost of all material, labour, T&P,Royalty, ISTP, labour cess and all other taxes but excluding G.S.T.) (i) 5th kilometre stone (precast) |
| 20 | Kilometre Stone Reinforced cement concrete M15grade kilometre stone of standard design as per IRC:8, fixing in position including painting and printing etc.As per MORT&H clause 8.14 (804) & including cost of all material, labour, T&P,Royalty, ISTP, labour cess and all other taxes but excluding G.S.T.) (ii) Ordinary kilometer stone (precast) |
| 21 | Plain cement concrete 1:3:6 nominal mix in foundation with crushed stone aggregate 40 mm nominal size mechanically mixed, placed in foundation and compacted by vibration including curing for 14 days. As per MORT&H Clause 9.03 & including cost of all material, labour, T&P,Royalty, ISTP, labour cess and all other taxes but excluding G.S.T.) |
| 22 | Brick masonry work in 1:3 in sub-structure complete excluding pointing and plastering, as per drawing and Technical Specifications & including cost of all material, labour, T&P,Royalty, ISTP, labour cess and all other taxes but excluding G.S.T.) |
| 23 | Supply, laying and fixing of 600 mm NP4 class hume pipes in proper position in culvert & including cost of all material, labour, T&P,Royalty, ISTP, labour cess and all other taxes but excluding G.S.T.) |
| 24 | Pointing with cement mortar (1:3) on brick work in substructure as per Technical Specifications & including cost of all material, labour, T&P,Royalty, ISTP, labour cess and all other taxes but excluding G.S.T.) |
| 25 | Plastering with cement mortar (1:3) on brick work in sub-structure as per Technical Specifications & including cost of all material, labour, T&P,Royalty, ISTP, labour cess and all other taxes but excluding G.S.T.) |
| 26 | Dismantling of existing structures like culverts, bridges, retaining walls and other structure comprising of masonry, cement concrete, wood work, steel work, including T&P and scaffolding wherever necessary, sorting the dismantled material, disposal of unserviceable material and stacking the serviceable material with all lifts and lead of 1000 metres. As per Morth Clause 2.04 (I)C, & including cost of all material, labour, T&P, labour cess and all other taxes but excluding G.S.T. |
| 27 | Earth work in excavation of foundation of structures as per drawing and technical specification, including setting out, construction of shoring and bracing, removal of stumps and other deleterious matter, dressing of sides and bottom, backfilling the excavation earth to the extent required and utilising the remaining earth locally for road work. As per Morth Clause 304B & including cost of all material, labour, T&P, labour cess and all other taxes but excluding G.S.T. |
| 28 | Sand Filling in Foundation Trenches as per Drawing & Technical Specification (As per Morth Sl.N. 15.03) & including cost of all material, labour, T&P, labour cess and all other taxes but excluding G.S.T. |
| 29 | Plain/Reinforced Cement Concrete in Open Foundation complete as per Drawing and Technical Specifications. (PCC Grade M15) As per Morth Clause 15.11 & including cost of all material, labour, T&P,Royalty, ISTP, labour cess and all other taxes but excluding G.S.T.) |
| 30 | PCC M15 Grade leveling course below approach slab complete as per drawing and Technical specification As per Morth Clause 15.15 & including cost of all material, labour, T&P,Royalty, ISTP, labour cess and all other taxes but excluding G.S.T.) |
| 31 | Plain/Reinforced Cement Concrete in Open Foundation complete as per Drawing and Technical Specifications. (PCC Grade M20) As per Morth Clause 15.11 & including cost of all material, labour, T&P,Royalty, ISTP, labour cess and all other taxes but excluding G.S.T.) |
| 32 | Plain/Reinforced Cement Concrete in Open Foundation complete as per Drawing and Technical Specifications. (RCC Grade M25) As per Morth Clause 15.11(E) & including cost of all material, labour, T&P,Royalty, ISTP, labour cess and all other taxes but excluding G.S.T.) |
| 33 | Plain/Reinforced Cement Concrete for wall & slab etc. complete as per Drawing and Technical Specifications. (RCC Grade M25). As per Morth Clause 15.12(B) & including cost of all material, labour, T&P,Royalty, ISTP, labour cess and all other taxes but excluding G.S.T.) |
| 34 | Reinforced cement concrete approach slab including reinforcement and formwork complete as per drawing and Technical specification. As per Morth 15.16 & including cost of all material, labour, T&P,Royalty, ISTP, labour cess and all other taxes but excluding G.S.T.) |
| 35 | Supplying, Fitting and Placing un-coated HYSD bar Reinforcement in Foundation complete as per Drawing and Technical Specifications. As per Morth Clause 15.13 & including cost of all material, labour, T&P, labour cess and all other taxes but excluding G.S.T. |
| 36 | Back filling behind abutment, wing wall and return wall complete as per drawing and Technical Specification (As per Morth Sl.N. 15.23) & including cost of all material, labour, T&P,Royalty, ISTP, labour cess and all other taxes but excluding G.S.T.) |
| 37 | Providing and laying Cement concrete wearing coat M-30 grade including reinforcement complete as per drawing and Technical Specifications. As per Morth Clause 15.18 & including cost of all material, labour, T&P,Royalty, ISTP, labour cess and all other taxes but excluding G.S.T.) |
| 38 | Providing weep holes in Brick masonry/ Plain/ Reinforced concrete abutment, wing wall/ return wall with 100 mm dia AC pipe, extending through the full width of the structure with slope of 1V:20H towards drawing face. Complete as per drawing and Technical Specifications (As per Morth Sl.N. 15.14) & including cost of all material, labour, T&P,Royalty, ISTP, labour cess and all other taxes but excluding G.S.T.) |
| 39 | Drainage Spouts complete as per drawing and Technical specification (As per Morth Sl.N. 15.17) & including cost of all material, labour, T&P, labour cess and all other taxes but excluding G.S.T. |
| 40 | Dewatering work of undergroung water as well as surface water with the help of diesel engine pumping set during earth work in excavation of foundation for laying lean concrete and brick work in foundation including cost of Boring charges @ 5 mtr c/c distance (or as required ), hire chargeg of pumping set, fuel charges, labour and other T&P including cost of operation as per requierment at site & as directed by the Engineer-in-charge & including cost of all material, labour, T&P, labour cess and all other taxes but excluding G.S.T. |
| 41 | Earth work in excavation of foundation of structures as per drawing and technical specification, including setting out, construction of shoring and bracing, removal of stumps and other deleterious matter, dressing of sides and bottom and backfilling with approved material. As per Morth Specification No.-15.01, 304(B) & including cost of all material, labour, T&P, labour cess and all other taxes but excluding G.S.T. |
| 42 | Sand Filling in Foundation Trenches as per Drawing & Technical Specification. As per MORTH Specification No. 304, S.I. 12.03 & including cost of all material, labour, T&P, labour cess and all other taxes but excluding G.S.T. |
| 43 | Plain cement concrete 1:3:6 nominal mix in foundation with crushed stone aggregate 40 mm nominal size mechanically mixed, placed in foundation and compacted by vibration including curing for 14 days. As per MORTH Specification No. 2100, S.I. 12.04 & including cost of all material, labour, T&P,Royalty, ISTP, labour cess and all other taxes but excluding G.S.T.) |
| 44 | Plain/Reinforced Cement Concrete in Open Foundation complete as per Drawing and Technical Specifications. 1500, 1700 & 2100 Sr 12.08E (RCC Grade M-25) & including cost of all material, labour, T&P,Royalty, ISTP, labour cess and all other taxes but excluding G.S.T.) |
| 45 | Plain/Reinforced cement concrete in sub-structure complete as per drawing and Technical Specifications 1500, 1700 & 2200 sr no. 13.05(F). (RCC Grade M-25) & including cost of all material, labour, T&P,Royalty, ISTP, labour cess and all other taxes but excluding G.S.T.) |
| 46 | Furnishing and Placing Reinforced/ Prestressed cement concrete in super-structure as per drawing and Technical Specification 14.01(b) (RCC Grade M-25) & including cost of all material, labour, T&P,Royalty, ISTP, labour cess and all other taxes but excluding G.S.T.) |
| 47 | Supplying, Fitting and Placing un-coated HYSD bar Reinforcement in Foundation complete asper Drawing and Technical Specifications. As per Morth Specification 12.42 S.I. 1600 & including cost of all material, labour, T&P, labour cess and all other taxes but excluding G.S.T. |
| 48 | Supplying, fitting and placing HYSD bar reinforcement in substructure complete as per drawing and Technical Specifications. As per Morth Specification 1600& 2200 & including cost of all material, labour, T&P, labour cess and all other taxes but excluding G.S.T. |
| 49 | Supplying, fitting and placing HYSD bar reinforcement in super structure complete as per drawing and technical specifications As per Morth Specification 1600 & including cost of all material, labour, T&P, labour cess and all other taxes but excluding G.S.T. |
| 50 | Brick Masonry Work in cement Mortor 1:3 in Foundation complete excluding Pointing and Plastering, as per Drawing and Technical Specifications. As per Morth Specification 1300 sr no. 12.05 & including cost of all material, labour, T&P,Royalty, ISTP, labour cess and all other taxes but excluding G.S.T.) |
| 51 | Brick Masonry Work in 1:3 in Substructure complete excluding Pointing and Plastering, as per Drawing and Technical Specifications. As per Morth Specification 1300 & 2200 sr no. 13.01 & including cost of all material, labour, T&P,Royalty, ISTP, labour cess and all other taxes but excluding G.S.T.) |
| 52 | Pointing with cement mortar (1:3) on brick work in substructure as per Technical Specifications. As per Morth Specification 1300 S.I. 13.2 & including cost of all material, labour, T&P,Royalty, ISTP, labour cess and all other taxes but excluding G.S.T.) |
| 53 | PCC M15 Grade leveling course below approach slab complete as per drawing and Technical specification. As per Morth Specification No. 2700 & 14.10 II (P.C.C. Grade M-15) & including cost of all material, labour, T&P,Royalty, ISTP, labour cess and all other taxes but excluding G.S.T.) |
| 54 | Reinforced cement concrete approach slab including reinforcement and formwork complete as per drawing and Technical specification. As per Morth Speciation No. 1500, 1600, 1700 & 2704 S.I. 14.11 & including cost of all material, labour, T&P,Royalty, ISTP, labour cess and all other taxes but excluding G.S.T.) |
| 55 | Drainage Spouts complete as per drawing and Technical specification. As per Morth Speciation No. 2705 S.I. 14.09 & including cost of all material, labour, T&P, labour cess and all other taxes but excluding G.S.T. |
| 56 | Providing and laying Cement concrete wearing coat M-30 grade including reinforcement complete as per drawing and Technical Specifications. As per MORTH Specification 2702, S.I. 14.04 & including cost of all material, labour, T&P,Royalty, ISTP, labour cess and all other taxes but excluding G.S.T.) |
| 57 | Back filling behind abutment, wing wall and return wall complete as per drawing and Technical Specification, As per MORTH Specification 170.1.4 of IRC:78 & 2200, S.I. 15.23 & including cost of all material, labour, T&P,Royalty, ISTP, labour cess and all other taxes but excluding G.S.T.) |
| 58 | Providing weep holes in Brick masonry/Plain/ Reinforced concrete abutment, wing wall/ return wall with 110 mm dia PVC pipe, extending through the full width of the structure with slope of 1V :20H towards drawing foce. Complete as per drawing and Technical Specifications & including cost of all material, labour, T&P,Royalty, ISTP, labour cess and all other taxes but excluding G.S.T.) |
| 59 | Dewatering work of undergrounding water as well as surface water with the help of diesel engine pumping set during earth work in excavation of foundation for laying lean concrete and brick work in foudation (or as required), hire charging of pumping set, Fuel charge, labour and other T&P including cost of operation as per requirement at site & as direction by Engineer-in-Charge & including cost of all material, labour, T&P, labour cess and all other taxes but excluding G.S.T. |
| 60 | Earth work in excavation of foundation of structures as per drawing and technical specification, including setting out, construction of shoring and bracing, removal of stumps and other deleterious matter, dressing of sides and bottom and backfilling with approved material. As per Morth Specification No.-15.01, 304(B) & including cost of all material, labour, T&P, labour cess and all other taxes but excluding G.S.T. |
| 61 | Providing and laying boulders apron on Canal bed for protection against scour with stone boulders weighing not less than 40 kg each complete as per drawing and Technical specification. (Cluase-15.10 (2503)) & including cost of all material, labour, T&P,Royalty, ISTP, labour cess and all other taxes but excluding G.S.T.) |
| 62 | Type - B, \\"THRIE\\" : Metal Beam Crash BarrierProviding and erecting a \\"Thrie\\" metal beam crash barrier comprising of 3 mm thick corrugated sheet metal beam rail, 85 cm above road/ground level, fixed on ISMC series channel vertical post, 150×75×5 mm spaced 2 m centre to centre, 2 m high with 1.15 m below ground level, all steel parts and fitments to be galvanized by hot dip process, all fittings to conform to IS:1367 and IS:1364, metal beam rail to be fixed on the vertical post with a space of channel section 150×75×5 mm. 546 mm long complete as per clause 810 & including cost of all material, labour, T&P, labour cess and all other taxes but excluding G.S.T. |
| 63 | Road Marking with Hot Applied Thermoplastic Compound with Reflectorising Glass Beads on Bituminous Surface. Providing and laying of hot applied thermoplastic compound 2.5 mm thick including reflectorising glass beads @ 250 gms per sqm area, thickness of 2.5 mm is exclusive of surface applied glass beads as per IRC:35 .The finished surface to be level, uniform and free from streaks and holes. As per MORT&H clause 8.13 (803) (Ch-6, Sl. 2) & including cost of all material, labour, T&P, labour cess and all other taxes but excluding G.S.T. |
| 64 | Road Marking with Hot Applied Thermoplastic Compound with Reflectorising Glass Beads on Bituminous Surface. (Repeated/ Transverse bar) Providing and laying of hot applied thermoplastic compound 5 mm thick including reflectorising glass beads @ 500 gms per sqm area, thickness of 5 mm is exclusive of surface applied glass beads as per IRC:35-2015 The finished surface to be level, uniform and free from streaks and holes. (Ch-6, Sl. 3) & including cost of all material, labour, T&P, labour cess and all other taxes but excluding G.S.T. |
| 65 | providing and fixing of retro-reflectorised cautionary, mandatory and informatory sign as per IRC :67-2012 made of high intensity grade sheeting type-IV vide clause 801.3, fixed over aluminium sheeting 1.5 mm thick supported on a mild steel angle iron post 75 mm×75 mm×6 mm firmly fixed to the ground by means of properly designed foundation with M 15 grade cement concrete 45 cm×45 cm×60 cm. 60 cm below ground level as per approved drawing. The Retro reflective sheeting shall be tested for a certificate of having the sheeting tested for coefficient of retro reflection, daytime colour and luminance, shrinkage, flexibility, liner removal, adhesion, impact resistance, specular gloss and fungus resistance, 3 years outdoor weathering and its having passed these tests shall be obtained from International/Government Laboratory Institute by the manufacturer of the sheeting and in case the certificate is obtained from international condition, it should also be obtained from Indian condition within 3 years of launching of product by the manufacture in abroad. Alternatively, a certificate conforming to ASTM Specification (D 4956-09) on artificial accelerated weathering requirements from a reputed laboratory in India can be accepted provisionally. In such a situation, the Employer/Client, if so desires, could seek for a performance guarantee which would be released after receipt of certificate meeting the requirement of three years outdoor weathering of the sheeting as per IRC 67.2012. Legends, letters, numerals and borders etc should be as per MORTH specification No-801.3.7. Proof of the same in form of government report shall be uploaded while quoting tender (CH-6 SI.No.18) & including cost of all material, labour, T&P, labour cess and all other taxes but excluding G.S.T. i) 90 cm equilateral triangle with diffinitation plate (20cm×60cm). Cautionary Sign board- For T / Y Junction |
| 66 | providing and fixing of retro-reflectorised cautionary, mandatory and informatory sign as per IRC :67-2012 made of high intensity grade sheeting type-IV vide clause 801.3, fixed over aluminium sheeting 1.5 mm thick supported on a mild steel angle iron post 75 mm×75 mm×6 mm firmly fixed to the ground by means of properly designed foundation with M 15 grade cement concrete 45 cm×45 cm×60 cm. 60 cm below ground level as per approved drawing. The Retro reflective sheeting shall be tested for a certificate of having the sheeting tested for coefficient of retro reflection, daytime colour and luminance, shrinkage, flexibility, liner removal, adhesion, impact resistance, specular gloss and fungus resistance, 3 years outdoor weathering and its having passed these tests shall be obtained from International/Government Laboratory Institute by the manufacturer of the sheeting and in case the certificate is obtained from international condition, it should also be obtained from Indian condition within 3 years of launching of product by the manufacture in abroad. Alternatively, a certificate conforming to ASTM Specification (D 4956-09) on artificial accelerated weathering requirements from a reputed laboratory in India can be accepted provisionally. In such a situation, the Employer/Client, if so desires, could seek for a performance guarantee which would be released after receipt of certificate meeting the requirement of three years outdoor weathering of the sheeting as per IRC 67.2012. Legends, letters, numerals and borders etc should be as per MORTH specification No-801.3.7. Proof of the same in form of government report shall be uploaded while quoting tender (CH-6 SI.No.18) & including cost of all material, labour, T&P, labour cess and all other taxes but excluding G.S.T.vii) 90 cm height Octagon |
| 67 | providing and fixing of retro-reflectorised cautionary, mandatory and informatory sign as per IRC :67-2012 made of high intensity grade sheeting type-IV vide clause 801.3, fixed over aluminium sheeting 1.5 mm thick supported on a mild steel angle iron post 75 mm×75 mm×6 mm firmly fixed to the ground by means of properly designed foundation with M 15 grade cement concrete 45 cm×45 cm×60 cm. 60 cm below ground level as per approved drawing. The Retro reflective sheeting shall be tested for a certificate of having the sheeting tested for coefficient of retro reflection, daytime colour and luminance, shrinkage, flexibility, liner removal, adhesion, impact resistance, specular gloss and fungus resistance, 3 years outdoor weathering and its having passed these tests shall be obtained from International/Government Laboratory Institute by the manufacturer of the sheeting and in case the certificate is obtained from international condition, it should also be obtained from Indian condition within 3 years of launching of product by the manufacture in abroad. Alternatively, a certificate conforming to ASTM Specification (D 4956-09) on artificial accelerated weathering requirements from a reputed laboratory in India can be accepted provisionally. In such a situation, the Employer/Client, if so desires, could seek for a performance guarantee which would be released after receipt of certificate meeting the requirement of three years outdoor weathering of the sheeting as per IRC 67.2012. Legends, letters, numerals and borders etc should be as per MORTH specification No-801.3.7. Proof of the same in form of government report shall be uploaded while quoting tender (CH-6 SI.No.18) & including cost of all material, labour, T&P, labour cess and all other taxes but excluding G.S.T. x)30 cm × 90 cm (Left/Right) Object Hazard |
| 68 | Direction and place Identification signs up to 0.90 sqm size Board :Providing and erecting direction and place identification retro-reflectorised sign as per IRC-67 made of high intensity grade sheeting The Retro reflective sheeting shall be tested for a certificate of having the sheeting tested for coefficient of retro reflection, daytime colour and luminance, shrinkage, flexibility. liner removal, adhesion, impact resistance, specular gloss and fungus resistance, 3 years outdoor weathering and its having passed these tests shall be obtained from International/Government Laboratory Institute by the manufacturer of the sheeting and in case the certificate is obtained from international condition, it should also be obtained from Indian condition within 3 years of launching of product by the manufacture in abroad. Alternatively, a certificate conforming to ASTM Specification (D 4956-09) on artificial accelerated weathering equirements from a reputed laboratory in India can be accepted provisionally. In such a situation, the Employer/Client, if so desires, could seek for a performance guarantee which would be released after receipt of certificate meeting the requirement of three years outdoor weathering of the sheeting as per IRC 67:2012. Legends, letters, numerals and borders etc should be as per MORTH specification No-801.3.7. Sheet fixed over aluminium sheeting 2 mm thick with area not exceeding 0.9 sqm. Supported on a mild steel single angle iron post 75×75×6 mm firmly fixed to the ground by means of property designed foundation with M-15 grade cement concrete 45×45×60 cm, below ground level as per approved drawing completed (CH-6 SI.No.19) & including cost of all material, labour, T&P, labour cess and all other taxes but excluding G.S.T. |
| 69 | 12 m-15 m Span Over Head Structure with 300 dia MS two vertical post Supply, fixing & erection of built up Overhead Structure of 12M-15M span comprising of two vertical posts of 6.00 M height made up of 300 mm NB heavy class MS pipe as vertical member welded with 10 mm MS plate at top & 12 mm M S plate at bottom. The horizontal Truss shall comprise of 50 mm dia heavy class M.S. pipe and 40 mm dia heavy M S pipe as bracing & 10 mm MS plate at bottom for fixing to vertical post as per structure design & drawing with one of steel primer and two coats of synthetic enamel plant. The work includes construction of RCC Foundation of size 0.90×0.90×1.50 m of required depth as per site condition for built up structure including Earth work in excavation 100 mm thick Lean Concrete in 1:3:6 (cement coarse sand and 40 mm gauge stone ballast and RCC M-25 cement concrete including supply and fixing of 25 mm dia Foundation Bolts 600 mm long as per provision of structure design including cost of reinforcement & shuttering The lateral vertical clearances and complete. Installation work shall be as per relevant clauses of MORT&H specification section 800 and IRC 67 2012 complete in all respect. The Rates shall include cost of design, fabrication, supply. transportations, Local shifting Erection of Signage structure using crane, inclusive of all taxes etc. all T&P machine, material and labour required for proper completion of work as per direction of Engineer-in charge (CH-6 SI.No.7) & including cost of all material, labour, T&P, labour cess and all other taxes but excluding G.S.T. |
| 70 | 6M Span overhead Cantilever Structure with 300dia MS one vertical post Supply, fixing & erection of built up Cantilever Structure 6 m span comprising of one vertical posts of 6.00 M height made up of 300 mm NB heavy class MS pipe as vertical member welded with 10 mm MS plate at top & 12 mm M S plate at bottom. The horizontal Truss shall comprise of 50 mm dia heavy class M. S. pipe and 40 mm dia heavy M S pipe as bracing & 10 mm M$ plate at bottom for fixing to vertical post as per structure design & drawing with one of steel primer and two coats of synthetic enamel plant. The work includes construction of RCC Foundation of size 0.90×0.90×1.50 m of required depth as per site condition for built up structure including Earth work in excavation 100 mm thick Lean Concrete in 1:3:6 cement coarse sand and 40 mm gauge stone ballast and RCC - M25 grade concrete including supply and fixing of 25 mm dia Foundation Bolts 600 mm long as per provision of structure design including cost of reinforcement & shuttering. The lateral vertical clearances and complete installation work shall be as per relevant clauses of MORT&H specification section 800 and IRC 67: 2012 complete in all respect The Rates shall include cost of design fabrication, supply, transportation Local shifting Erection of Signage structure using crane, inclusive of all taxes etc. all T&P machine, material and labour required for proper completion of work as per direction of Engineer-in-charge. (CH-6 SI.No.4) & including cost of all material, labour, T&P, labour cess and all other taxes but excluding G.S.T. |
| 71 | Providing & erecting sign board with corrosion resistant made of 2mm thick aluminium sheet or 4mm thick ACP sheet face to be fully covered with miicroprismatic full cube technology type-XI grade retro reflective sheeting shalll be fully processed on base aluminium substrate and also fixed on the angle frame on 35x35x5mm as per IRC-67 with vertical and laterial clearance giving in para 80.2 &802.3 and clause 801.3 (CH-6 SI.No.10) & including cost of all material, labour, T&P, labour cess and all other taxes but excluding G.S.T. |
| 72 | Road DelineatorDelineator: Supply & Fixing of MS Delineator made of Mild steel with pure polyester powder coating with the minimum thickness of powder coating of not less than 40 micron for protection against corrosion. The surface should be concealed so that there should not be any exposed surface without powder coating. Alternatively, these metal guide poles can be concealed with thermoplastic body. The posts shall have lan ellipsoidal or circular design with the height of the pole shall be 800 to 900 mm above the ground with about 200 to 300 mm base which can be anchored onto the ground. Mild steel Guide Poles shall conform to Type XI sheeting specifications as per IRC:67 and ASTM D4956 which would ensure to obtain clear visibility of the road alignment during night time. The Retro reflective sheeting shall be tested for A certificate of having the sheeting tested for coefficient of retro reflection, daytime colour and luminance, shrinkage, flexibility, liner removal, adhesion, impact resistance, specular gloss and fungus resistance, 3 years outdoor weathering and its having passed these tests shall be obtained from International Government Laboratory/Institute by the manufacturer of the sheeting and in case the certificate is obtained from international condition, it should also be obtained from Indian condition within 3 years of launching of product by the manufacture in abroad. Alternatively, a certificate conforming to ASTM Specification (D4956-09) on artificial accelerated weathering requirements from a reputed laboratory in India can be accepted provisionally. In such a situation, the Employer/Client, if so desires, could seek for a performance guarantee which would be released after receipt of certificate meeting the requirement of three years outdoor weathering of the sheeting as per IRC 67:2012 & Proof of the same Report shall be uploaded which quoting tender. The rate shall include all materials, labour T&P. transportation, installation and incidentals all complete as per direction of the Engineer-in-Charge. (Ch-6, S.No. 1) & including cost of all material, labour, T&P, labour cess and all other taxes but excluding G.S.T. |
| 73 | Reflective Raised Pavement Markers (Cat Eye/Road Stud)Supply and fixing of raised pavement marker with Made of Plastic body of RPM/ Road Stud shall be moulded from ASA (Acrylic Styrene Acrylonitrite) or HIPS (High-impact Polystyrene) or Acrylonitrite Butadiene Styrene (ABS) or Any other suitable material approved by the Engineer. The Marker shall support a load of 13,635 kg tested in accordance with ASTM D4280. The Reflective panels shall consist of number of lenses containing single or dual prismatic cubes capable of providing total internal reflection of the light entering the lens face. Lenses shall be moulded of methyl methecrylate conforming to ASTM D788 of equivalent. The slop or retro-reflecting surface shall preferably be 35+1-5 degree to base and the area of each retro -reflecting surface shall not be less than 13.00 sq.cm. the marker height shall not be less than 10 mm and shall not exceed 20 mm & Width shall not exceed 130 mm. The base of the marker shall be flat within 1.3 mm all road studs shall be legibly marked with the name , trade or other means of identification of the manufacture. epoxy installations, excess adhesive around the edge of the marker, excess adhesive on the pavement and adhesive on the exposed surfaces of the markers shall be immediately removed. The contractor shall submit a two year warranty for satisfactory field performance including stipulated retro-reflectance of the reflecting panel, to the Engineer. In addition, a two year warranty for satisfactory infield performance of the finished road marker shall also be given by the contractor who carries out the work of fixing of reflective road markers. In case the markers are displaced, damaged get worn out or lose their reflectivity compared to stipulated standards, the contractor would be required to replace all such markers within 15 days of the intimation from the Engineer, at his own cost. The rate shall include all materials, labour, T&P, transportation, installation and incidentals all complete as per direction of the Engineer-in-Charge. (Ch-6, S.No. 5) (RPM with Shank) & including cost of all material, labour, T&P, labour cess and all other taxes but excluding G.S.T. |
| 74 | 05 Year Maintenance Charge For 1nd Year Routine Maitenance of road for 05 Years after the competion of work (Vide shasanadesh No. 17/2024/सा0-113/23-1-2024-23-1099/113/2023 Dated 16.01.2024 & letter No. 36890C/RMC/Mool-23-24 Dated 17.02.2024 of ENC PWD. Rate Excluding of G.S.T.)1st Year @ Nil |
| 75 | 05 Year Maintenance Charge For 2nd Year @ 0.25%Routine Maitenance of road for 05 Years after the competion of work (Vide shasanadesh No. 17/2024/सा0-113/23-1-2024-23-1099/113/2023 Dated 16.01.2024 & letter No. 36890C/RMC/Mool-23-24 Dated 17.02.2024 of ENC PWD. Rate Excluding of G.S.T.) |
| 76 | 05 Year Maintenance Charge For 3rd Year @ 0.50%Routine Maitenance of road for 05 Years after the competion of work (Vide shasanadesh No. 17/2024/सा0-113/23-1-2024-23-1099/113/2023 Dated 16.01.2024 & letter No. 36890C/RMC/Mool-23-24 Dated 17.02.2024 of ENC PWD. Rate Excluding of G.S.T.) |
| 77 | 05 Year Maintenance Charge For 4th Year @ 0.75%Routine Maitenance of road for 05 Years after the competion of work (Vide shasanadesh No. 17/2024/सा0-113/23-1-2024-23-1099/113/2023 Dated 16.01.2024 & letter No. 36890C/RMC/Mool-23-24 Dated 17.02.2024 of ENC PWD. Rate Excluding of G.S.T.) |
| 78 | 05 Year Maintenance Charge For 5th Year @ 1.00%Routine Maitenance of road for 05 Years after the competion of work (Vide shasanadesh No. 17/2024/सा0-113/23-1-2024-23-1099/113/2023 Dated 16.01.2024 & letter No. 36890C/RMC/Mool-23-24 Dated 17.02.2024 of ENC PWD. Rate Excluding of G.S.T.) Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Sep 28, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedOct 24, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 22 daysOct 24, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 22 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender