Tender For Special Reparis To Dandus Point Jetty At Sri Vijaya Puram
Tender Value
Ref. Documents
Estimated cost
Bid Submission
12 Oct 2026
9 days left
EMD
79996
Bank guarantee accepted
Document Fee
Ref. Documents
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
South Andamans → Andaman And Nicobar Islands
EMD Exemption
Not Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for Special Reparis To Dandus Point Jetty At Sri Vijaya Puram
BOQ
| Sl. No. | Item Description |
| 1 | Surface preparation to receive micro concrete by chipping to depth of max.75mm, cleaning, removing the traces of dust, loose concrete etc.including cost of all labour charges, minor tools, labour welfare cess, GST etc.complete. |
| 2 | Replacement of reinforcement as additional bars including bending, cutting, welding and fixing, including cost of steel, transportation charges, all labour charges, minor tools, labour welfare cess, GST etc.complete. |
| 3 | Steel centering and shuttering including strutting proping etc.and removal of form for :Columns, Pillars, Pipes, Abutments, Posts and struts, including cost of all materials, all labour charges, minor tools, labour welfare cess, GST etc.complete. |
| 4 | Drilling holes in the existing structure with mechanized boring machine to an average dia of 100mm at required location for pouring the micro concrete including cost of all labour charges and machineries, minor tools, LWC & GST etc.complete. |
| 5 | Supply and apply of high strength, non shrink cementilous free flow micro concrete (With minimum 28 days flexural strength 50 Kg/ Sqcm and compressive strength 500 Kg/Sqcm. As per BS 4551-80) for above water level using 12mm down size graded stone chips with the ratio of 1:0.75 (1 high strength & non shrink cementitious micro concrete chemical 0.75 12mm to 6mm stone chips) on site to enable completion of pouring in a continous operation. An approved grout concrete mixer of slow speed heavy duty drill and exact quality of water as recommended should be poured into the mixing vessel with cleaned stone chips of size 12mm to 6 mm slowly and mix the same thoroughly in a forced action. The mixed material should be placed immediately to positioned formwork continously to an average thickness of 75mm without any gap.including cost of all materials, labour charges, minor tools, labour welfare cess, GST etc.complete. |
| 6 | Anticorrosive coat on bars : Supplying , preparing and priming the reinforcement steel with Epoxy Zinc primer or Epoxy Zinc Primer or epoxy anti corrosive paint ( Confirming to IS/BS certification ), including cost of all materials all about charges, minor tools, LWC & GST etc., complete. |
| 7 | Supply and application of Epoxy Conctete Bonding agent (Confirming to and having BS 6319 certification) cleaned and properly prepared old concrete surface to give good bonding between old and new concrete, including cost of all materials, labour charges, minor tools, labour welfare cess, GST etc.complete. |
| 8 | Supplying, mixing and applying CURING MEMBRANE or equivalent with water including cost of materials, labour charges, minor tools, labour welfare cess, GST etc.complete. |
| 9 | Protective Coat : Supplying and applying two coats of IPH - Conguard or DECKGUARD 'S' or equivalent by spray or brush over the prepared surface and allow it to dry including cost of materials, labour, brushes, tools, equipments labour welfare cess, GST etc. complete. The polymer material properties are to be as follows: 1. Water absorption test in (%) : 0.15 % |
| 10 | Lockset: Mark the holes at the required spot. Drill the pilot holes using 14mm dia hammer drill bit to a depth of 150mm. Clean the holes with the good water. Mix the base and hardener of Polyester resin LOKSET \\"S\\" or equivalent pour the same to the 2/3 of the depth and insert the shear connecting rod of 12 mm dia gently in to the prepared holes. Pack the gap if any. Allow it to set for min. 20 minutes without disturbing including cost of all materials, all labour charges, labour welfare cess, GST, etc. complete. |
| 11 | Providing and fixing the sacrificial anode (Fosroc Galvashield XP or equivalent) over the main reinforcement of pile, pile caps, columns, Deck Beams and Deck Slabs etc. as per the manufacturer specification and designed spacings, as sacrificial anode to the reinforcement against corrosion, Including cost of all materials, machineries and labour charges, minor tools, labour welfare cess, GST etc., Complete. |
| 12 | Supply of Motor Launcher as & when required for transportation of department staff for supervision including hire charges of engine dinghy with fuel & operator, minor tools, LWC & GST etc., complete. Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Sep 28, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedOct 12, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 9 daysOct 13, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 10 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender