Tender For Standing Order For Carrying Out Balance Civil And Miscellaneous Works At Hbls Integrated Sugar Plant At Sugauli, East Ch Aran Bihar.
Tender Value
Ref. Documents
Estimated cost
Bid Submission
19 Oct 2026
19 days left
EMD
13 Lakhs
Bank guarantee accepted
Document Fee
Ref. Documents
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Pashchim Champaran → Bihar
EMD Exemption
Not Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for Standing Order For Carrying Out Balance Civil And Miscellaneous Works At Hbls Integrated Sugar Plant At Sugauli, East Ch Aran Bihar.
BOQ
| Sl. No. | Item Description |
| 1 | Earthwork excavation for foundations, pits, plinth beams, etc. |
| 2 | Earthwork excavation for foundations, pits, plinth beams, etc. up to 2.10 m depth below existing ground level in all types of soil excluding hard rock, including dressing and leveling of sides and bottom, dewatering/bailing out of water if encountered, providing necessary shoring and strutting, and disposal of surplus excavated earth within or outside HBL premises to an approved / unobjectionable location as directed by the Engineer-in-Charge, including spreading, watering, leveling and compaction complete in all respects.The rate shall include all labour, tools & tackles, equipment, lead, lift, royalties and incidental charges complete. |
| 3 | Earthwork excavation for foundations, pits, plinth beams, etc. below 2.10 m and up to 3.50 m depth existing ground level in all types of soil excluding hard rock, including dressing and leveling of sides and bottom, dewatering/bailing out of water if encountered, providing necessary shoring and strutting, and disposal of surplus excavated earth within or outside HBL premises to an approved/unobjectionable location as directed by the Engineer-in-Charge, including spreading, watering, leveling and compaction complete in all respects.The rate shall include all labour, tools & tackles, equipment, lead, lift, royalties and incidental charges complete. |
| 4 | Excavating trenches by mechinical / manual means of required width for pipes, cables, etc upto 80 mm dia including excavation for sockets, and dressing of sides, ramming of bottoms, for all depth, including getting out the excavated soil, and then returning the soil as required, in layers not exceeding 20 cm in depth, including consolidating each deposited layer by ramming, watering, etc. and disposing of surplus excavated soil as directed, within a lead of 50 m. |
| 5 | Excavating trenches by mechinical / manual means of required width for pipes, cables, etc more than 80 mm dia up to 300 mm dia including excavation for sockets, and dressing of sides, ramming of bottoms, for all depth, including getting out the excavated soil, and then returning the soil as required, in layers not exceeding 20 cm in depth, including consolidating each deposited layer by ramming, watering, etc. and disposing of surplus excavated soil as directed, within a lead of 50 m. |
| 6 | Excavating trenches by mechinical / manual means of required width for pipes, cables, etc more than 300 mm dia up to 600 mm including excavation for sockets, and dressing of sides, ramming of bottoms, for all depth, including getting out the excavated soil, and then returning the soil as required, in layers not exceeding 20 cm in depth, including consolidating each deposited layer by ramming, watering, etc. and disposing of surplus excavated soil as directed, within a lead of 50 m. |
| 7 | Backfilling around foundations, trenches, plinth beams, pits, etc. with approved excavated earth in layers not exceeding 200 mm compacted thickness, including breaking clods, watering, ramming and compacting to required density complete as directed by the Engineer-in-Charge.The rate shall include all labour, tools & tackles, equipment and incidental charges complete.Measurement for payment shall be based on compacted volume. |
| 8 | Supply and filling of approved local river sand in plinth, foundations, under footings, around foundations, trenches, etc. in layers not exceeding 200 mm compacted thickness, including conveying, spreading, watering, ramming, compacting, consolidating and dressing to required levels, grades and densities complete as per specifications and as directed by the Engineer-in-Charge.The rate shall include cost of sand, loading, unloading, transportation, royalty, all leads and lifts, labour, tools & tackles, equipment and all incidental charges complete.Measurement for payment shall be based on compacted volume. |
| 9 | Providing and laying damp-proof course (DPC) 40 mm thick in cement concrete of proportion 1:2:4 (1 cement : 2 coarse sand, Zone-III, derived from natural sources : 4 graded stone aggregate of 12.5 mm nominal size, derived from natural sources), including preparation and cleaning of the surface, laying, compacting and finishing the concrete to the required line, level, slope and thickness, with necessary curing, all complete as per drawings, specifications and directions of the Engineer-in-Charge.Rate shall include all materials, labour, tools, plant, equipment, transportation, loading/unloading, mixing, laying, compaction, finishing, curing and all incidental works necessary for satisfactory completion of the DPC. |
| 10 | Providing and laying Plain Cement Concrete (PCC) in leveling course of nominal mix 1:4:8 (1 Cement : 4 Coarse Sand : 8 Graded Stone Aggregate) using 40 mm and down graded stone aggregates, including batching, mixing, conveying, laying, compacting with mechanical vibrators, finishing to required line, level and slope, curing, and all necessary formwork/shuttering complete as per specifications and as directed by the Engineer-in-Charge.The rate shall include cost of all materials, labour, machinery, tools & tackles, water, curing, formwork, all leads and lifts and incidental charges complete.Measurement for payment shall be based on finished concrete volume. |
| 11 | Providing and laying Plain Cement Concrete (PCC) in leveling course of nominal mix 1:3:6 (1 Cement : 3 Coarse Sand : 6 Graded Stone Aggregate) using 20 mm and down graded stone aggregates, including batching, mixing, conveying, laying, compacting with mechanical vibrators, finishing to required line, level and slope, curing, and all necessary formwork/shuttering complete as per specifications and as directed by the Engineer-in-Charge.The rate shall include cost of all materials, labour, machinery, tools & tackles, water, curing, formwork, all leads and lifts and incidental charges complete.Measurement for payment shall be based on finished concrete volume. |
| 12 | Providing and laying Plain Cement Concrete (PCC) in leveling course of nominal mix 1:2:4 (1 Cement : 2 Coarse Sand : 4 Graded Stone Aggregate) using 20 mm and down graded stone aggregates, including batching, mixing, conveying, laying, compacting with mechanical vibrators, finishing to required line, level and slope, curing, and all necessary formwork/shuttering complete as per specifications and as directed by the Engineer-in-Charge.The rate shall include cost of all materials, labour, machinery, tools & tackles, water, curing, formwork, all leads and lifts and incidental charges complete.Measurement for payment shall be based on finished concrete volume. |
| 13 | Providing and laying Reinforced Cement Concrete (RCC) works up to Plinth Level of M25 grade Design Mix with minimum cement content of 360 kg/cum, using 20 mm and down graded machine crushed stone aggregates, in footings, pile caps, rafts, pedestals, columns, walls, plinth beams, curbs, equipment foundations, trenches, drains, Slab (excluading grade slab) and other RCC works, including batching, machine mixing, conveying, placing, vibrating with mechanical vibrators, tamping, compacting, finishing, curing and rendering of concrete surfaces wherever required, complete as per specifications and as directed by the Engineer-in-Charge.The design mix shall be got approved from the Consultant/Engineer-in-Charge based on necessary laboratory testing of materials and trial mixes before commencement of concreting work.The rate shall include cost of all materials excluding reinforcement steel, labour, machinery, tools & tackles, admixtures if required, all leads and lifts, and providing, erecting and dismantling of necessary centering, shuttering/formwork using steel/plywood shuttering with staging, scaffolding, bracing, supports, chamfers, fillets, surface preparation, hacking of concrete surfaces to receive plaster/finishes and all incidental works complete.Reinforcement steel shall be measured and paid separately under relevant item.Measurement for payment shall be based on finished concrete volume. |
| 14 | Providing and laying Reinforced Cement Concrete (RCC) work above Plinth level up to 10 m level of M25 grade Design Mix with minimum cement content of 360 kg/cum, using 20 mm and down graded machine crushed stone aggregates, in footings, pile caps, rafts, pedestals, columns, walls, plinth beams, curbs, equipment foundations, trenches, drains, Slab (excluading grade slab) and other RCC works, including batching, machine mixing, conveying, placing, vibrating with mechanical vibrators, tamping, compacting, finishing, curing and rendering of concrete surfaces wherever required, complete as per specifications and as directed by the Engineer-in-Charge.The design mix shall be got approved from the Consultant/Engineer-in-Charge based on necessary laboratory testing of materials and trial mixes before commencement of concreting work.The rate shall include cost of all materials excluding reinforcement steel, labour, machinery, tools & tackles, admixtures if required, all leads and lifts, and providing, erecting and dismantling of necessary centering, shuttering/formwork using steel/plywood shuttering with staging, scaffolding, bracing, supports, chamfers, fillets, surface preparation, hacking of concrete surfaces to receive plaster/finishes and all incidental works complete.Reinforcement steel shall be measured and paid separately under relevant item.Measurement for payment shall be based on finished concrete volume. |
| 15 | Providing and laying Reinforced Cement Concrete (RCC) work above 10.00 m level of M25 grade Design Mix with minimum cement content of 360 kg/cum, using 20 mm and down graded machine crushed stone aggregates, in footings, pile caps, rafts, pedestals, columns, walls, plinth beams, curbs, equipment foundations, trenches, drains, Slab (excluading grade slab) and other RCC works, including batching, machine mixing, conveying, placing, vibrating with mechanical vibrators, tamping, compacting, finishing, curing and rendering of concrete surfaces wherever required, complete as per specifications and as directed by the Engineer-in-Charge.The design mix shall be got approved from the Consultant/Engineer-in-Charge based on necessary laboratory testing of materials and trial mixes before commencement of concreting work.The rate shall include cost of all materials excluding reinforcement steel, labour, machinery, tools & tackles, admixtures if required, all leads and lifts, and providing, erecting and dismantling of necessary centering, shuttering/formwork using steel/plywood shuttering with staging, scaffolding, bracing, supports, chamfers, fillets, surface preparation, hacking of concrete surfaces to receive plaster/finishes and all incidental works complete.Reinforcement steel shall be measured and paid separately under relevant item.Measurement for payment shall be based on finished concrete volume. |
| 16 | Providing and laying Reinforced Cement Concrete (RCC) of M25 grade Design Mix with minimum cement content of 360 kg/cum, using 20 mm and down graded machine crushed stone aggregates, in grade slab/ flooring/ walkway at FFL level including batching, machine mixing, conveying, placing, vibrating with mechanical vibrators, tamping, compacting, finishing, curing and rendering of concrete surfaces wherever required, complete as per specifications and as directed by the Engineer-in-Charge.The design mix shall be got approved from the Consultant/Engineer-in-Charge based on necessary laboratory testing of materials and trial mixes before commencement of concreting work.The rate shall include cost of all materials excluding reinforcement steel, labour, machinery, tools & tackles, admixtures if required, all leads and lifts, and providing, erecting and dismantling of necessary centering, shuttering/formwork using steel/plywood shuttering with staging, scaffolding, bracing, supports, chamfers, fillets, surface preparation, hacking of concrete surfaces to receive plaster/finishes and all incidental works complete.Reinforcement steel shall be measured and paid separately under relevant item.Measurement for payment shall be based on finished concrete volume. |
| 17 | Providing, laying, spreading and compacting Granular Sub Base (GSB) over prepared sub-grade using graded stone aggregates conforming to Grading Zone V or VI of Table 400-1 of latest MORTH Specifications, with aggregate size 75 mm and down graded, complete as directed by the Engineer-in-Charge.The work shall include preparation of sub-grade, supply and transportation of approved materials to site for all leads and lifts, spreading in uniform layers of 125 mm to 150 mm compacted thickness, watering, mixing, grading and compacting with suitable vibratory/power rollers of minimum 10 tonne capacity including dry rolling and wet rolling to achieve specified compaction and density as per MORTH specifications.The item shall also include dressing to required line, grade, camber and levels, making up depressions/settlements by adding approved material, re-rolling wherever required and all operations necessary for proper completion of Granular Sub Base work complete in all respects.The rate shall include cost of all materials, loading, unloading, transportation, labour, machinery, rollers, water, tools & tackles, quality control tests, all leads and lifts and incidental charges complete.Measurement for payment shall be based on finished compacted volume. |
| 18 | Construction of Wet Mix Macadam (WMM) by providing, laying, spreading and compacting graded crushed stone aggregates using 53 mm and down graded aggregates conforming to MORTH Specifications, mixed with 2% Ordinary Portland Cement by weight of aggregate, complete as directed by the Engineer-in-Charge.The work shall include proportioning and mixing of aggregates with water at Optimum Moisture Content (OMC) in approved mechanical wet mix plant, transportation of mixed material to site in tippers, conveying to mechanical paver, laying over previously prepared surface to required thickness, line, grade, camber and alignment, compacting with 8–10 tonne vibratory roller/power roller to achieve minimum 95% of maximum dry density as per specifications including dry rolling and wet rolling.The item shall also include preparation of surface, edge protection of WMM layers, correction of irregularities, making up depressions/settlements with additional material and re-rolling to achieve specified finish and compaction complete in all respects.The rate shall include cost of aggregates, cement, water, loading, unloading, transportation, labour, machinery, wet mix plant operations, paver, rollers, lighting arrangements, maintenance of diversion roads if required, royalties, seigniorage charges, approvals from mining/applicable authorities, quality control tests, all leads and lifts and incidental charges complete.The work shall be executed in accordance with latest MORTH Specification Clause 406 (4th Revision) and as directed by the Engineer-in-Charge.Measurement for payment shall be based on finished compacted volume. |
| 19 | Providing and laying in position ready mixed or site batched Design Mix Cement Concrete of M30 grade for pavement/road works using coarse and fine aggregates derived from natural sources, Ordinary Portland Cement (OPC) / Portland Pozzolana Cement (PPC) / Portland Slag Cement (PSC), and approved admixtures in recommended proportions conforming to IS:9103 for improving workability, durability and setting characteristics without impairing strength, complete as per drawings, specifications and directions of the Engineer-in-Charge in panels using slotted ms channel shuttering of depth equal to the thickness of the pavement with required stiffness and fixing arrangement to keep them in position and enable to resist horizontal pressure of concrete, machine mixing, vibrating with screed board vibrator, pond curing for 14 days, vacuum dewatering, finished with power troweling concreting and surface texturing as per latest specification The concrete shall have minimum cement content of 350 kg/cum and shall be designed to achieve the specified strength and durability requirements. The work shall include batching, machine mixing, transportation, pumping/placing of concrete at site, laying, compacting with mechanical vibrators, curing, carriage for all leads and lifts and all operations necessary for completion of pavement concrete work complete in all respects. |
| 20 | The item shall also include rate for providing approved quality polythene paper (minimum 125 gsm) below the driveway, forming/cutting of grooves, expansion/construction joints in approved pattern and dimensions, cleaning of grooves/joints and filling/sealing with approved hot applied bituminous sealant/compound complete as directed by the Engineer-in-Charge.The rate shall include cost of all materials, admixtures, bituminous joint filler/sealant, labour, machinery, batching plant operations, transit mixers, pumps, groove cutting equipment, tools & tackles, water, quality control tests and incidental charges complete, but excluding cost of centering/shuttering, surface finishing/texturing.Reinforcement steel and dowel bar shall be measured and paid separately under relevant items. |
| 21 | Providing, driving and installing driven cast in-situ Reinforced Cement Concrete piles of specified diameter and length below pile cap level using hydraulic piling rigs with suitable power units, complete as per drawings, specifications and directions of the Engineer-in-Charge.The work shall include positioning and setting up piling rig, driving of casing/shell where required, supplying and placing M25 grade Design Mix concrete (As per approved Design Mix), providing and fixing pile shoe, driving and forming piles to the required depth and carrying safe working load not less than specified, withdrawing casing where applicable, maintaining alignment and verticality, cutting pile heads to required levels and all incidental works necessary for proper completion of piling works complete in all respects.The rate shall include cost of pile shoe, concrete, reinforcement up to 336 kg, labour, machinery, hydraulic piling rigs, power units, with bentonite solution, tools & tackles, all leads and lifts and incidental charges complete, Any reinforcement steel above 336 Kg shall be measured and paid separately under relevant item.)For actual drilling done pro-rata rate will be applied.(Size of Pile = Dia = 500mm, Depth= 20m) |
| 22 | Pile Breaking: Breaking / trimming of cast-in-situ reinforced concrete pile head of 500 mm diameter up to 2.0 m length from Natural Ground Level (NGL), including chipping, removal of weak / contaminated concrete, exposing reinforcement bars without damage, cutting and bending of reinforcement as per drawing, disposal of debris within site premises, and all necessary labour, tools & tackles complete as directed by Engineer-in-Charge. |
| 23 | Providing and fixing steel reinforcement for Reinforced Cement Concrete (RCC) works using ready-to-use “Cut, Bend and Tie” reinforcement bars of approved make, manufactured and processed at approved factory/workshop and transported to construction site, complete as per drawings, specifications and directions of the Engineer-in-Charge.The work shall include supply, cutting, bending, straightening, placing in position, tying with binding with 16 gauge MS annealed binding wire, providing necessary overlaps, hooks, chairs, spacers and supports for maintaining proper cover, alignment and spacing complete for all RCC works at all levels.Reinforcement steel shall consist of Thermo-Mechanically Treated (TMT) bars of grade Fe-500D or higher conforming to relevant IS specifications.The rate shall include cost of reinforcement steel, binding wire, wastage, cutting and bending charges, transportation, loading/unloading, labour, tools & tackles, all leads and lifts and incidental charges complete. |
| 24 | Providing and fixing high-yield reinforcement bars size = 12mm and minimum depth = 150mm into existing RCC/concrete by chemical anchoring, including setting out, drilling holes of required diameter and embedment depth using approved (rotary hammer/core) drilling equipment, thorough cleaning of holes by brushing and compressed air/vacuum, supplying and injecting approved chemical/epoxy anchoring adhesive, inserting and fixing reinforcement bars to the specified embedment, and ensuring proper bonding, alignment and projection, including all labour, materials, consumables, tools, equipment, wastage, cleaning and making good complete as directed by the Engineer.Reinforcement shall be measured and paid for separately. |
| 25 | Providing and fixing high-yield reinforcement bars size = 16 mm and minimum depth = 192mm into existing RCC/concrete by chemical anchoring, including setting out, drilling holes of required diameter and embedment depth using approved (rotary hammer/core) drilling equipment, thorough cleaning of holes by brushing and compressed air/vacuum, supplying and injecting approved chemical/epoxy anchoring adhesive, inserting and fixing reinforcement bars to the specified embedment, and ensuring proper bonding, alignment and projection, including all labour, materials, consumables, tools, equipment, wastage, cleaning and making good complete as directed by the Engineer.Reinforcement shall be measured and paid for separately. |
| 26 | Providing and fixing high-yield reinforcement bars size = 20 mm and minimum depth = 240mm into existing RCC/concrete by chemical anchoring, including setting out, drilling holes of required diameter and embedment depth using approved (rotary hammer/core) drilling equipment, thorough cleaning of holes by brushing and compressed air/vacuum, supplying and injecting approved chemical/epoxy anchoring adhesive, inserting and fixing reinforcement bars to the specified embedment, and ensuring proper bonding, alignment and projection, including all labour, materials, consumables, tools, equipment, wastage, cleaning and making good complete as directed by the Engineer.Reinforcement shall be measured and paid for separately. |
| 27 | Providing and fixing high-yield reinforcement bars size = 25 mm and minimum depth = 250mm into existing RCC/concrete by chemical anchoring, including setting out, drilling holes of required diameter and embedment depth using approved (rotary hammer/core) drilling equipment, thorough cleaning of holes by brushing and compressed air/vacuum, supplying and injecting approved chemical/epoxy anchoring adhesive, inserting and fixing reinforcement bars to the specified embedment, and ensuring proper bonding, alignment and projection, including all labour, materials, consumables, tools, equipment, wastage, cleaning and making good complete as directed by the Engineer.Reinforcement shall be measured and paid for separately. |
| 28 | Vertical Load Testing of piles in accordance with IS 2911 -IV including installation of loading paltform and preparation of pile head or construction of test cap and dismantling of test cap after test etc.complete as per specification . |
| 29 | Lateral load Testing of piles in accordance with IS 2911 -IV including installation of loading paltform and preparation of pile head or construction of test cap and dismantling of test cap after test etc.complete as per specification . |
| 30 | Pull Out Testing of piles in accordance with IS 2911 -IV including installation of loading paltform and preparation of pile head or construction of test cap and dismantling of test cap after test etc.complete as per specification . |
| 31 | Providing and constructing brick masonry work in substructure below plinth level using first quality burnt clay bricks of Class Designation 7.5 (75 KG / SQCM minimum) in cement mortar 1:6 (1 cement : 6 coarse sand), complete as per drawings, specifications and directions of the Engineer-in-Charge.The work shall include soaking of bricks before use, preparation of mortar, laying bricks in proper line, level and plumb with full mortar joints, providing all openings, offsets, projections, embeds and recesses as required, raking out joints to 10 mm depth for plastering/finishing, scaffolding, curing and all cutting, fitting and finishing works complete in all respects.The rate shall include cost of bricks, cement, sand, water, labour, scaffolding, tools & tackles, curing, all leads and lifts and incidental charges complete. |
| 32 | Providing and constructing brick masonry work in the superstructure from 0 (plinth) to 4.50 m level using first quality burnt clay bricks of Class Designation 7.5 (75 KG / SQCM minimum) in cement mortar 1:6 (1 cement : 6 coarse sand), complete as per drawings, specifications and directions of the Engineer-in-Charge.The work shall include soaking of bricks before use, preparation of mortar, laying bricks in proper line, level and plumb with full mortar joints, providing all openings, offsets, projections, embeds and recesses as required, raking out joints to 10 mm depth for plastering/finishing, scaffolding/staging, curing and all cutting, fitting and finishing works complete in all respects.The rate shall include cost of bricks, cement, sand, water, labour, scaffolding/staging, tools & tackles, curing, all leads and lifts up to 15 m height and incidental charges complete. |
| 33 | Providing and constructing brick masonry work in the superstructure from 4.50 m level up to 9.00 m level using first quality burnt clay bricks of Class Designation 7.5 (75 KG / SQCM minimum) in cement mortar 1:6 (1 cement : 6 coarse sand), complete as per drawings, specifications and directions of the Engineer-in-Charge.The work shall include soaking of bricks before use, preparation of mortar, laying bricks in proper line, level and plumb with full mortar joints, providing all openings, offsets, projections, embeds and recesses as required, raking out joints to 10 mm depth for plastering/finishing, scaffolding/staging, curing and all cutting, fitting and finishing works complete in all respects.The rate shall include cost of bricks, cement, sand, water, labour, scaffolding/staging, tools & tackles, curing, all leads and lifts up to 15 m height and incidental charges complete. |
| 34 | Providing and constructing brick masonry work in superstructure above 9 m level using first quality burnt clay bricks of Class Designation 7.5 (75 KG / SQCM minimum) in cement mortar 1:6 (1 cement : 6 coarse sand), complete as per drawings, specifications and directions of the Engineer-in-Charge.The work shall include soaking of bricks before use, preparation of mortar, laying bricks in proper line, level and plumb with full mortar joints, providing all openings, offsets, projections, embeds and recesses as required, raking out joints to 10 mm depth for plastering/finishing, scaffolding/staging, curing and all cutting, fitting and finishing works complete in all respects.The rate shall include cost of bricks, cement, sand, water, labour, scaffolding/staging, tools & tackles, curing, all leads and lifts up to 15 m height and incidental charges complete. |
| 35 | Providing and laying 115 mm thick half brick partition wall in cement mortar 1:4 (1 cement : 4 coarse sand) using approved quality table moulded chamber burnt clay bricks, complete at all levels as per drawings, specifications and directions of the Engineer-in-Charge.The work shall include soaking of bricks before use, preparation of mortar, laying bricks in proper line, level and plumb with full mortar joints, embedding 8 mm dia Tor steel reinforcement bars at every fourth course of brick masonry, proper anchoring to RCC/structural members, scaffolding/staging, curing and all cutting, fitting and finishing works complete in all respects.The rate shall include cost of bricks, cement, sand, reinforcement steel, binding wire, water, labour, scaffolding/staging, tools & tackles, all leads and lifts and incidental charges complete. |
| 36 | Providing and laying Flat brick soling (approx 75mm layer) below grade slab/floor using approved first class kiln burnt clay bricks conforming to IS:1077, laid flat/edge to edge over prepared and compacted sub-grade in proper line and level, including filling joints with sand, watering, ramming, consolidation, cutting of bricks wherever required, and all labour, materials, T&P, lead, lift, loading, unloading, wastages and incidental charges complete as per specifications and as directed by Engineer-in-Charge. |
| 37 | Providing and laying Edge to egde brick soling (approx 115mm layer) below grade slab/floor using approved first class kiln burnt clay bricks conforming to IS:1077, laid flat/edge to edge over prepared and compacted sub-grade in proper line and level, including filling joints with sand, watering, ramming, consolidation, cutting of bricks wherever required, and all labour, materials, T&P, lead, lift, loading, unloading, wastages and incidental charges complete as per specifications and as directed by Engineer-in-Charge. |
| 38 | Breaking and dismantling of reinforced cement concrete (RCC) work at all levels and heights by manual / mechanical means, including cutting of reinforcement, careful handling to avoid damage to adjoining structures, stacking of serviceable materials, and disposal of unserviceable debris to a designated location within the site or as directed by the Engineer-in-Charge, complete in all respects. |
| 39 | Breaking and dismantling of Plain cement concrete (PCC) work at all levels and heights by manual / mechanical means, careful handling to avoid damage to adjoining structures, stacking of serviceable materials, and disposal of unserviceable debris to a designated location within the site or as directed by the Engineer-in-Charge, complete in all respects. |
| 40 | Breaking and dismantling of brick masonry / ruble masonry work at all levels and heights by manual / mechanical means, careful handling to avoid damage to adjoining structures, stacking of serviceable materials, and disposal of unserviceable debris to a designated location within the site or as directed by the Engineer-in-Charge, complete in all respects. |
| 41 | Supplying and fixing dowel bars in RCC pavement, rigid pavement joints and other concrete areas complete as per IFC drawings, specifications and directions of the Engineer-in-Charge.The work shall include supply of dowel bars conforming to IS:432 Grade-I, cutting, straightening, machining, epoxy coating, fixing in proper alignment and position, provision of approved plastic sheathing on one end and all accessories required for proper load transfer arrangement in expansion/construction joints as per latest specifications of IRC:15 and IRC:58.For expansion joints, the item shall include providing and fixing closely fitting caps of minimum 100 mm length with closed end made of GI pipe or stiff plastic sleeve of minimum 2 mm thickness over the sheathed end of each dowel bar. Necessary expansion space equal to thickness of joint filler board shall be maintained between cap end and dowel bar end using approved compressible sponge filler. The arrangement shall be properly sealed/taped all around to prevent ingress of cement slurry.The work shall also include placing, supporting and securing dowel bars with approved alignment assemblies, spacers, chairs and supports to maintain proper line, level and spacing during concreting operations complete in all respects.The rate shall include cost of dowel bars, epoxy coating, sheathing, GI/plastic caps, compressible sponge filler, spacers, supports, fixing accessories, labour, tools & tackles, all leads and lifts and incidental charges complete.Approved make/brand of dowel bars and accessories shall be as approved by the Engineer-in-Charge. |
| 42 | Preparing and plastering internal wall surfaces at all heights with 12 mm thick cement plaster in cement mortar 1:4 (1 cement : 4 coarse sand), finished smooth with trowel and sponge, complete as per drawings, specifications and directions of the Engineer-in-Charge.The work shall include preparation of surfaces, hacking/raking out joints wherever required, cleaning, wetting, applying plaster to true line, level and plumb, smooth sponge finish, curing and all necessary scaffolding/staging complete in all respects.The item shall also include providing 6 mm x 6 mm recessed grooves at junctions of RCC and brick masonry surfaces, neatly formed and finished to avoid surface cracks and ensure proper architectural finish complete.The rate shall include cost of cement, sand, groove forming arrangements, water, labour, scaffolding/staging, tools & tackles, curing, all leads and lifts and incidental charges complete. |
| 43 | Preparing and plastering specified masonry, RCC and other surfaces at all heights with 6 mm thick cement plaster in cement mortar 1:3 (1 cement : 3 fine sand), finished smooth with trowel and sponge, complete as per drawings, specifications and directions of the Engineer-in-Charge.The work shall include preparation of surfaces, cleaning, hacking/raking out joints wherever required, wetting, applying plaster to the specified thickness and to true line, level and plumb, finishing of corners, edges, junctions, jambs and soffits, smooth sponge finish, curing and all necessary scaffolding/staging complete in all respects.The item shall also include proper preparation and treatment of junctions between RCC and brick masonry surfaces and providing 6 mm x 6 mm recessed grooves wherever shown or required, neatly formed and finished to avoid surface cracks and ensure proper architectural finish complete.The rate shall include cost of cement, fine sand, groove forming arrangements, water, labour, scaffolding/staging, tools & tackles, curing, all leads and lifts and incidental charges complete. |
| 44 | Providing and laying average 20 mm thick sand faced cement plaster in two coats on external wall surfaces at all heights in cement mortar 1:3 (1 cement : 3 coarse sand), complete as per drawings, specifications and directions of the Engineer-in-Charge.The work shall include preparation of surfaces, scaffolding/staging, providing and fixing chicken wire mesh at all junctions of brick masonry and RCC surfaces with minimum 150 mm overlap in all directions, groove cutting/forming wherever required, and providing additional thickness of plaster as necessary to achieve true line, level and plumb without any extra cost.The first coat shall consist of 12 mm thick cement plaster in CM 1:3 mixed with approved make waterproofing compound in proportion as per manufacturer’s specifications and finished rough to receive second coat.The second coat shall consist of 8 mm thick cement plaster in CM 1:3 finished with sponge rubbing to obtain uniform sand faced texture and proper architectural finish complete in all respects.The rate shall include cost of cement, sand, waterproofing compound, chicken mesh, water, labour, scaffolding/staging, curing, tools & tackles, all leads and lifts and incidental charges complete. |
| 45 | White washing with lime to give an even shade, of approved quality, over prepared plastered/masonry surfaces, complete as per drawings, specifications and directions of Engineer-in-Charge. The work shall include surface preparation, cleaning, preparation and application of lime wash in required coats to achieve uniform shade and finish, including scaffolding/staging, labour, tools & tackles, materials, wastage, leads, lifts and incidental charges complete.New Work 3 or more coats |
| 46 | Providing and applying 12 mm thick cement plaster of cement mortar 1:4 (1 cement : 4 coarse sand) on the internal surfaces of brick masonry drains, including preparation of surface, raking out joints, finishing the plastered surface smooth and even, and applying neat cement punning over the finished plastered surface, complete as directed by the Engineer-in-Charge.The rate shall include cost of cement, sand, groove forming arrangements, water, labour, tools & tackles, curing, all leads and lifts and incidental charges complete. |
| 47 | Distempering with 1st quality acrylic distemper (ready mixed) having VOC content less than 50 gram/litre, of approved manufacturer and required shade/colour, for new work, with two or more coats over and including one coat of water-thinnable cement primer having VOC content less than 50 gram/litre, complete as per drawings, specifications and directions of Engineer-in-Charge. The work shall include surface preparation, cleaning, minor repairs, application of primer and distemper coats uniformly to achieve an even and smooth shade, including scaffolding/staging, labour, tools & tackles, materials, wastage, leads, lifts and incidental charges complete. |
| 48 | Finishing walls with acrylic smooth exterior paint without silicone additives, of approved manufacturer and required shade/colour, for new work, with two or more coats applied @ 1.67 litre/10 sqm over and including one coat of exterior primer @ 0.90 litre/10 sqm, complete as per drawings, specifications and directions of Engineer-in-Charge. The work shall include surface preparation, cleaning, removal of loose particles and minor imperfections, application of primer and finish coats uniformly to achieve smooth, even and durable finish, including scaffolding/staging, labour, tools & tackles, materials, wastage, leads, lifts and incidental charges complete. |
| 49 | Finishing surfaces with epoxy paint On Steel Work: Providing and applying two or more coats of approved quality epoxy paint at all locations, of required shade and colour, over properly prepared surfaces and including suitable/compatible priming coat, complete as per manufacturer’s specifications, drawings and directions of Engineer-in-Charge. The work shall include surface preparation, cleaning, removal of dust, grease, loose particles and existing defective coating, minor repairs, application of primer and epoxy finish coats uniformly to achieve smooth, even and durable finish, including necessary scaffolding/staging, labour, tools & tackles, materials, wastage, leads, lifts and incidental charges complete. |
| 50 | Finishing surfaces with epoxy paint On Concrete Work: Providing and applying two or more coats of approved quality epoxy paint at all locations, of required shade and colour, over properly prepared surfaces and including suitable/compatible priming coat, complete as per manufacturer’s specifications, drawings and directions of Engineer-in-Charge. The work shall include surface preparation, cleaning, removal of dust, grease, loose particles and existing defective coating, minor repairs, application of primer and epoxy finish coats uniformly to achieve smooth, even and durable finish, including necessary scaffolding/staging, labour, tools & tackles, materials, wastage, leads, lifts and incidental charges complete. |
| 51 | Painting of rain water, soil, waste and vent pipes and fittings 75 mm diameter pipes:Providing and applying two or more coats of black anticorrosive bitumastic paint of approved brand and manufacture to rain water, soil, waste and vent pipes and fittings on new work, over and including one coat of ready-mixed zinc chromate yellow primer, complete as per drawings, specifications, manufacturer's recommendations and directions of Engineer-in-Charge. The work shall include surface preparation, cleaning, removal of rust, dust, grease and loose particles, application of primer and bitumastic paint uniformly to achieve a smooth, continuous and protective finish, including labour, brushes, tools & tackles, scaffolding/staging wherever required, materials, wastage, all leads, lifts and incidental charges complete.2 or more coats |
| 52 | Painting of rain water, soil, waste and vent pipes and fittings 100 mm diameter pipes:Providing and applying two or more coats of black anticorrosive bitumastic paint of approved brand and manufacture to rain water, soil, waste and vent pipes and fittings on new work, over and including one coat of ready-mixed zinc chromate yellow primer, complete as per drawings, specifications, manufacturer's recommendations and directions of Engineer-in-Charge. The work shall include surface preparation, cleaning, removal of rust, dust, grease and loose particles, application of primer and bitumastic paint uniformly to achieve a smooth, continuous and protective finish, including labour, brushes, tools & tackles, scaffolding/staging wherever required, materials, wastage, all leads, lifts and incidental charges complete.2 or more coats |
| 53 | Painting of rain water, soil, waste and vent pipes and fittings 150 mm diameter pipes:Providing and applying two or more coats of black anticorrosive bitumastic paint of approved brand and manufacture to rain water, soil, waste and vent pipes and fittings on new work, over and including one coat of ready-mixed zinc chromate yellow primer, complete as per drawings, specifications, manufacturer's recommendations and directions of Engineer-in-Charge. The work shall include surface preparation, cleaning, removal of rust, dust, grease and loose particles, application of primer and bitumastic paint uniformly to achieve a smooth, continuous and protective finish, including labour, brushes, tools & tackles, scaffolding/staging wherever required, materials, wastage, all leads, lifts and incidental charges complete.2 or more coats |
| 54 | Painting with synthetic enamel paint of approved brand and manufacture and required shade/colour to give an even shade, for new work with two or more coats, over properly prepared and primed surfaces, complete as per drawings, specifications and directions of Engineer-in-Charge. The work shall include surface preparation, cleaning, sanding/rubbing, removal of dust, rust and loose particles, minor making good, application of suitable primer and synthetic enamel finish coats uniformly to achieve smooth, even and durable finish, including scaffolding/staging wherever required, labour, materials, tools & tackles, wastage, all leads, lifts and incidental charges complete. |
| 55 | Painting with acid proof paint of approved brand and manufacture and required colour to give an even shade, for new work with two or more coats, over properly prepared surfaces, complete as per drawings, specifications and directions of Engineer-in-Charge. The work shall include surface preparation, cleaning, removal of dust, grease, loose particles and minor imperfections, application of suitable primer where specified and acid-proof finish coats uniformly to achieve a smooth, even and durable chemical-resistant finish, including scaffolding/staging wherever required, labour, materials, tools & tackles, wastage, all leads, lifts and incidental charges complete. |
| 56 | Painting with aluminium paint of approved brand and manufacture and required shade/finish to give an even shade, for new work with two or more coats, over properly prepared surfaces, complete as per drawings, specifications and directions of Engineer-in-Charge. The work shall include surface preparation, cleaning, removal of dust, rust, grease and loose particles, application of suitable primer where specified and aluminium paint coats uniformly to achieve smooth, even and durable finish, including scaffolding/staging wherever required, labour, materials, tools & tackles, wastage, all leads, lifts and incidental charges complete. |
| 57 | Providing and applying white cement based putty, of approved manufacturer, average 1 mm thickness over plastered ceiling surfaces, complete as per drawings, specifications and directions of Engineer-in-Charge. The work shall include surface preparation, cleaning, filling of minor imperfections, application of putty, sanding/rubbing to obtain smooth and even finish, including scaffolding/staging, labour, tools & tackles, materials, wastage, leads, lifts and incidental charges complete. |
| 58 | Providing and applying white cement based putty, of approved manufacturer, average 2 mm total thickness in two or more coats over plastered wall surfaces, complete as per drawings, specifications and directions of Engineer-in-Charge. The work shall include surface preparation, cleaning, filling of minor imperfections, application of successive coats, drying, sanding/rubbing and obtaining smooth and even finish, including scaffolding/staging, labour, tools & tackles, materials, wastage, leads, lifts and incidental charges complete. |
| 59 | Providing and applying two coats of acrylic emulsion paint internal: Providing and applying two coats of approved quality acrylic emulsion paint of required shade and colour over prepared plastered/puttied and primed wall surfaces, complete as per drawings, specifications and directions of Engineer-in-Charge. The work shall include preparation of surface, removal of dust and loose particles, rubbing down/sanding wherever required, application of primer wherever specified, filling and making good minor imperfections, application of two uniform coats of acrylic emulsion paint by brush/roller/spray as approved, allowing adequate drying between coats and obtaining smooth, even and uniform finish. The rate shall include cost of paint, thinning medium, labour, brushes, rollers, tools & tackles, scaffolding/staging, wastage, all leads and lifts and incidental charges complete. |
| 60 | Cement concrete flooring 40 mm thick in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate) with 20 mm nominal size stone aggregate, finished with a floating coat of neat cement, including cement slurry, complete as per drawings, specifications and directions of Engineer-in-Charge. The work shall include preparation and cleaning of base, laying, compacting, levelling and finishing to required line, level and slope, providing neat cement floating coat and curing, including all materials, labour, tools & tackles, scaffolding wherever required, leads, lifts, wastage and incidental charges complete. |
| 61 | Providing and fixing glass strips in joints of terrazzo/cement concrete flooring, including cutting and preparing joints, fixing 40 mm wide and 4 mm thick glass strips true to line, level and alignment, properly embedded and secured in cement mortar/slurry, complete as per drawings, specifications and directions of Engineer-in-Charge. The rate shall include cost of glass strips, cement mortar/slurry, labour, cutting, fixing, tools & tackles, wastage, leads, lifts and incidental charges complete. |
| 62 | Providing and laying 1st quality ceramic glazed floor tiles of size 300 × 300 mm, conforming to IS 15622, of approved make, colour and shade, laid on 20 mm thick cement mortar 1:4 (1 cement : 4 coarse sand), including cement slurry @ 3.3 kg/sqm, properly aligned, levelled and bedded. The work shall include cutting and fixing tiles to required line, level and slope, jointing and pointing with white cement and matching pigment, cleaning and finishing complete as per drawings, specifications and directions of Engineer-in-Charge. Rate shall include tiles, cement, sand, slurry, pigment, labour, tools & tackles, wastage, leads, lifts and incidental charges complete. |
| 63 | Providing and fixing 1st quality ceramic glazed tiles conforming to IS 15622, of approved make, colour and shade, of size as approved by Engineer-in-Charge, for skirting, risers of steps and dados, laid over 12 mm thick cement mortar 1:3 (1 cement : 3 coarse sand) and jointed with grey cement slurry @ 3.3 kg/sqm, including cutting, fitting, alignment, levelling and pointing of joints with white cement mixed with matching pigment, complete as per drawings, specifications and directions of Engineer-in-Charge. Rate shall include tiles, cement, sand, slurry, pigment, labour, cutting, wastage, tools & tackles, leads, lifts and incidental charges complete. |
| 64 | Providing and laying 1st quality 600 mm X 600 mm vitrified floor tiles of approved make, size and shade, thickness as specified by manufacturer, having water absorption < 0.08% and conforming to IS 15622, laid on 20 mm thick cement mortar 1:4 (1 cement : 4 coarse sand), including grey cement slurry @ 3.3 kg/sqm, properly aligned, levelled and laid to required line, level and slope. Joints shall be grouted/pointed with white cement and matching pigment, including cutting, fitting, cleaning and finishing complete as per drawings, specifications and directions of Engineer-in-Charge. Rate shall include tiles, cement, sand, slurry, grout/pigment, labour, cutting, wastage, tools & tackles, leads, lifts and incidental charges complete. |
| 65 | Providing and laying 1st quality 800 mm X 800 mm vitrified floor tiles of approved make, size and shade, thickness as specified by manufacturer, having water absorption < 0.08% and conforming to IS 15622, laid on 20 mm thick cement mortar 1:4 (1 cement : 4 coarse sand), including grey cement slurry @ 3.3 kg/sqm, properly aligned, levelled and laid to required line, level and slope. Joints shall be grouted/pointed with white cement and matching pigment, including cutting, fitting, cleaning and finishing complete as per drawings, specifications and directions of Engineer-in-Charge. Rate shall include tiles, cement, sand, slurry, grout/pigment, labour, cutting, wastage, tools & tackles, leads, lifts and incidental charges complete. |
| 66 | Providing and laying 1st quality 600 mm X 600 mm vitrified tiles of approved make, size, colour and shade, thickness as specified by the manufacturer, having water absorption less than 0.08% and conforming to IS 15622, in skirting and risers of steps, laid over 12 mm thick cement mortar 1:3 (1 cement : 3 coarse sand) and jointed with grey cement slurry @ 3.3 kg/sqm. The work shall include cutting, fitting, alignment, levelling and grouting of joints with white cement and matching pigment, complete as per drawings, specifications and directions of Engineer-in-Charge. Rate shall include tiles, cement, sand, cement slurry, white cement, matching pigment, labour, cutting, wastage, tools & tackles, leads, lifts and incidental charges complete. |
| 67 | Providing and laying 1st quality 800 mm X 800 mm vitrified tiles of approved make, size, colour and shade, thickness as specified by the manufacturer, having water absorption less than 0.08% and conforming to IS 15622, in skirting and risers of steps, laid over 12 mm thick cement mortar 1:3 (1 cement : 3 coarse sand) and jointed with grey cement slurry @ 3.3 kg/sqm. The work shall include cutting, fitting, alignment, levelling and grouting of joints with white cement and matching pigment, complete as per drawings, specifications and directions of Engineer-in-Charge. Rate shall include tiles, cement, sand, cement slurry, white cement, matching pigment, labour, cutting, wastage, tools & tackles, leads, lifts and incidental charges complete. |
| 68 | Providing and laying polished granite stone flooring of approved make, colour, shade and texture in required design and patterns, in linear as well as curvilinear portions, with 18 mm thick granite stone slabs laid over 20 mm average thick cement mortar 1:4 (1 cement : 4 coarse sand). The work shall include laying and jointing with cement slurry, pointing joints with white cement slurry mixed with matching pigment, cutting, edge dressing, alignment, rubbing, curing and polishing as required to achieve the specified finish, complete as per architectural drawings, specifications and directions of Engineer-in-Charge. Rate shall include granite slabs, cement, sand, slurry, pigment, labour, cutting, wastage, tools & tackles, curing, rubbing/polishing, leads, lifts and incidental charges complete.Polished Granite stone slab of all colour and texture. |
| 69 | Providing and fixing 18 mm thick gang saw cut (Area of slab upto 0.50 square meter), polished and machine-cut marble stone for wall lining/veneer work, of approved Raj Nagar plain white marble/Udaipur green marble/Zebra black marble, over average 12 mm thick backing grout in cement mortar 1:3 (1 cement : 3 coarse sand), including jointing and pointing with white cement mortar 1:2 (1 white cement : 2 marble dust) mixed with pigment to match marble shade. The work shall include cutting, dressing, fixing, alignment, levelling, cleaning and finishing complete as per drawings, specifications and directions of Engineer-in-Charge. Marble shall be secured to backing with cramps, cramps being measured and paid separately. Rate shall include marble, cement, sand, marble dust, pigment, grout, labour, cutting, dressing, tools & tackles, scaffolding, wastage, leads, lifts and incidental charges complete. |
| 70 | Providing and fixing 18 mm thick gang saw cut (Area of slab over 0.50 square meter), polished and machine-cut marble stone for wall lining/veneer work, of approved Raj Nagar plain white marble/Udaipur green marble/Zebra black marble, over average 12 mm thick backing grout in cement mortar 1:3 (1 cement : 3 coarse sand), including jointing and pointing with white cement mortar 1:2 (1 white cement : 2 marble dust) mixed with pigment to match marble shade. The work shall include cutting, dressing, fixing, alignment, levelling, cleaning and finishing complete as per drawings, specifications and directions of Engineer-in-Charge. Marble shall be secured to backing with cramps, cramps being measured and paid separately. Rate shall include marble, cement, sand, marble dust, pigment, grout, labour, cutting, dressing, tools & tackles, scaffolding, wastage, leads, lifts and incidental charges complete. |
| 71 | Providing edge moulding to 18 mm thick marble stone counters, Vanities etc., including machine polishing to edge to give high gloss finish etc. complete as per design approved by Engineerin- Charge. |
| 72 | Providing and laying Kota stone slabs, 20 mm thick, in treads and risers of staircase, of approved quality and shade, laid over 12 mm average thick cement mortar 1:3 (1 cement : 3 coarse sand), including jointing with grey cement slurry mixed with pigment to match the shade of stone, cutting, dressing, edge finishing, rubbing and polishing complete, including providing the stone in single length for each tread/riser wherever required, all complete as directed by Engineer-in-Charge. |
| 73 | Extra for providing pre-finished nosing to treads of steps in Kota stone/sand stone slab, including fixing and finishing complete. |
| 74 | Providing and fixing 10 mm thick acid and/or alkali resistant tiles of approved make, colour, shade, texture and size, conforming to IS 4457, on prepared concrete/cement mortar surface, laid over 10 mm thick bedding mortar in the proportion of 1:4 (1 part acid-proof cement : 4 parts coarse sand), including providing and applying acid and/or alkali resistant cement for filling and finishing the joints, cutting, shaping and fitting tiles around corners, edges, columns, floor traps and other obstructions, maintaining uniform line, level and slope, cleaning, curing and final finishing, complete in all respects as specified and directed by the Engineer-in-Charge. The tiles and jointing materials shall be resistant to the acids, alkalis, chemicals and other substances likely to come in contact with the finished surface. All materials, labour, tools, tackles, scaffolding and incidental works necessary for proper completion shall be included. |
| 75 | Providing and fixing 10 mm thick acid and/or alkali resistant tiles of approved make, colour, shade, texture and size, conforming to IS 4457, in dado/skirting over prepared surface, laid on 12 mm thick bedding mortar in the proportion of 1:4 (1 part acid-proof cement : 4 parts coarse sand), including filling and finishing joints with acid and/or alkali resistant cement, cutting, dressing, fixing, alignment, finishing and cleaning complete, including all materials, labour, tools and incidental works, as directed by the Engineer-in-Charge. |
| 76 | Providing and fixing expansion hold fasteners with threaded dia of 6 mm on C.C. /R.C.C./Brick masonry surface backing including drilling necessary holes and the cost of bolt etc complete. |
| 77 | Providing and fixing expansion hold fasteners with threaded dia of 10 mm on C.C. /R.C.C./Brick masonry surface backing including drilling necessary holes and the cost of bolt etc complete. |
| 78 | Providing and fixing expansion hold fasteners with threaded dia of 12 mm on C.C. /R.C.C./Brick masonry surface backing including drilling necessary holes and the cost of bolt etc complete. |
| 79 | Providing and fixing expandable fasteners 25 mm long size with necessary plastic sleeves and galvanised M.S. screws including drilling holes in masonry work /CC/ R.C.C. and making good etc. complete. |
| 80 | Providing and fixing expandable fasteners 32 mm long size with necessary plastic sleeves and galvanised M.S. screws including drilling holes in masonry work /CC/ R.C.C. and making good etc. complete. |
| 81 | Providing and fixing expandable fasteners 40 mm long size with necessary plastic sleeves and galvanised M.S. screws including drilling holes in masonry work /CC/ R.C.C. and making good etc. complete. |
| 82 | Providing and fixing expandable fasteners 50 mm long size with necessary plastic sleeves and galvanised M.S. screws including drilling holes in masonry work /CC/ R.C.C. and making good etc. complete. |
| 83 | Providing and fixing false ceiling at all height including providing and fixing of frame work made of special sections, power pressed from M.S. sheets and galvanized with zinc coating of 120 gms/sqm (both side inclusive) as per IS : 277 and consisting of angle cleats of size 25 mm wide x 1.6 mm thick with flanges of 27 mm and 37mm, at 1200 mm centre to centre, one flange fixed to the ceiling with dash fastener 12.5 mm dia x 50mm long with 6mm dia bolts, other flange of cleat fixed to the angle hangers of 25x10x0.50 mm of required length with nuts & bolts of required size and other end of angle hanger fixed with intermediate G.I. channels 45x15x0.9 mm running at the spacing of 1200 mm centre to centre, to which the ceiling section 0.5 mm thick bottom wedge of 80 mm with tapered flanges of 26 mm each having lips of 10.5 mm, at 450 mm centre to centre, shall be fixed in a direction perpendicular to G.I. intermediate channel with connecting clips made out of 2.64 mm dia x 230 mm long G.I. wire at every junction, including fixing perimeter channels 0.5 mm thick 27 mm high having flanges of 20 mm and 30 mm long, the perimeter of ceiling fixed to wall/partition with the help of rawl plugs at 450 mm centre, with 25mm long dry wall screws @ 230 mm interval, including fixing of gypsum board to ceiling section and perimeter channel with the help of dry wallscrews of size 3.5 x 25 mm at 230 mm c/c, including jointing and finishing to a flush finish of tapered and square edges of the board with recommended jointing compound , jointing tapes, finishing with jointing compound in 3 layers covering upto 150 mm on both sides of joint and two coats of primer suitable for board, all as per manufacturer’s specification and also including the cost of making openings for light fittings, grills, diffusers, cutouts made with frame of perimeter channels suitably fixed, all complete as per drawings, specification and direction of the Engineer in Charge but excluding the cost of painting with : 12.5 mm thick tapered edge gypsum plain board conforming to IS: 2095- (Part I) :2011 (Board with BIS certification marks) |
| 84 | Providing and fixing tiled false ceiling of GI Metal Ceiling Lay-in plain Tegular edge Global White colour tiles of size 595x595 mm, 0.5 mm thick with 8 mm drop, made of GI sheet having galvanizing of 100 gms/sqm (both sides inclusive) and electrostatically polyester powder coated of thickness 60 microns (minimum), including factory painted after bending, in true horizontal level, suspended on inter locking metal grid of hot dipped galvanized steel sections (galvanized @ 120 grams/sqm, both side inclusive) consisting of main “T” runner with suitably spaced joints to get required length and of size 24x38 mm made from 0.30 mm thick (minimum) sheet, spaced at 1200 mm center to center and cross “T” of size 24x25 mm made of 0.30 mm thick (minimum) sheet, 1200 mm long spaced between main “T” at 600 mm center to center to form a grid of 1200x600 mm and secondary cross “T” of length 600 mm and size 24x25 mm made of 0.30 mm thick (minimum) sheet to be interlocked at middle of the 1200x600 mm panel to form grids of 600x600 mm and wall angle of size 24x24x0.3 mm and laying false ceiling tiles of approved texture in the grid including required cutting/making, opening for services like diffusers, grills, light fittings, fixtures, smoke detectors etc. Main “T” runners to be suspended from ceiling using GI slotted cleats of size 27 x 37 x 25 x 1.6 mm fixed to ceiling with 12.5 mm dia and 50 mm long dash fasteners, 4 mm GI adjustable rods with galvanised butterfly level clips of size 85 x 30 x 0.8 mm spaced at 1200 mm center to center along main T, bottom exposed width of 24 mm of all T-sections shall be pre-painted with polyester paint, all complete for all heights as per specifications, drawings and as directed by Engineer-in-charge. |
| 85 | Providing and fixing tiled false ceiling of GI Metal Ceiling Lay in perforated Tegular edge global white colour tiles of size 595x595 mm and 0.5 mm thick with 8 mm drop; made of GI sheet having galvanizing of 100 gms/ sqm (both sides inclusive) and 20% perforation area with 1.8 mm dia holes and having NRC (Noise Reduction Coefficient ) of 0.5, electro statically polyester powder coated of thickness 60 microns (minimum), including factory painted after bending and perforation, and backed with a black Glass fiber acoustical fleece, in true horizontal level, suspended on inter locking metal grid of hot dipped galvanized steel sections (galvanized @ 120 grams/sqm, both side inclusive) consisting of main “T” runner with suitably spaced joints to get required length and of size 24x38 mm made from 0.30 mm thick (minimum) sheet, spaced at 1200 mm center to center and cross “T” of size 24x25 mm made of 0.30 mm thick (minimum) sheet, 1200 mm long spaced between main “T” at 600 mm center to center to form a grid of 1200x600 mm and secondary cross “T” of length 600 mm and size 24x25 mm made of 0.30 mm thick (minimum) sheet to be interlocked at middle of the 1200x600 mm panel to form grids of 600x600 mm and wall angle of size 24x24x0.3 mm and laying false ceiling tiles of approved texture in the grid including required cutting/making, opening for services like diffusers, grills, light fittings, fixtures, smoke detectors etc. Main “T” runners to be suspended from ceiling using GI slotted cleats of size 27 x 37 x 25 x 1.6 mm fixed to ceiling with 12.5 mm dia and 50 mm long dash fasteners, 4 mm GI adjustable rods with galvanised butterfly level clips of size 85 x 30 x 0.8 mm spaced at 1200 mm center to center along main T, bottom exposed width of 24 mm of all T-sections shall be pre-painted with polyester paint, all complete for all heights as per specifications, drawings and as directed by Engineer-in-charge. |
| 86 | Providing and fixing tiled false ceiling of 12.5 mm thick square edge PVC Laminated Gypsum Tile of size 595x595 mm, made of Gypsum plasterboard, manufactured from natural gypsum as per IS 2095 part I and laminated with white 0.16mm thick fire retardant PVC film on the face side and 12micron metalized polyester on the back side with all edges sealed with the face side PVC film which goes around and wraps the edges and is bonded to the edges and the back side metalized polyester film so as to make the tile a completely sealed unit, in true horizontal level, suspended on inter locking metal grid of hot dipped galvanized steel sections (galvanized @ 120 grams/sqm, both side inclusive) consisting of main “T” runner with suitably spaced joints to get required length and of size 24x38 mm made from 0.30 mm thick (minimum) sheet, spaced at 1200 mm center to center and cross “T” of size 24x25 mm made of 0.30 mm thick (minimum) sheet, 1200 mm long spaced between main “T” at 600 mm center to center to form a grid of 1200x600 mm and secondary cross “T” of length 600 mm and size 24x25 mm made of 0.30 mm thick (minimum) sheet to be interlocked at middle of the 1200x600 mm panel to form grids of 600x600 mm and wall angle of size 24x24x0.3 mm and laying false ceiling tiles of approved texture in the grid including required cutting/making, opening for services like diffusers, grills, light fittings, fixtures, smoke detectors etc. Main “T” runners to be suspended from ceiling using GI slotted cleats of size 27 x 37 x 25 x 1.6 mm fixed to ceiling with 12.5 mm dia and 50 mm long dash fasteners, 4 mm GI adjustable rods with galvanised butterfly level clips of size 85 x 30 x 0.8 mm spaced at 1200 mm center to center along main T, bottom exposed width of 24 mm of all T-sections shall be pre-painted with polyester paint, all complete for all heights as per specifications, drawings and as directed by Engineer-in-charge. |
| 87 | Providing and fixing tiled false ceiling of 12.5 mm thick fully Perforated Gypsum Board tile made from plasterboard having glass fibre conforming to IS: 2095 part I, of size 595x595 mm, having perforation of 9.7x9.7 mm at 19.4 mm c/c with center borders of 48 mm and the side borders of 30 mm, backed with non woven tissue on the back side, having an NRC (Noise Reduction Coefficient) of 0.79, with 50 mm resin bonded glass wool backing, in true horizontal level, suspended on inter locking metal grid of hot dipped galvanized steel sections (galvanized @ 120 grams/sqm, both side inclusive) consisting of main “T” runner with suitably spaced joints to get required length and of size 24x38 mm made from 0.30 mm thick (minimum) sheet, spaced at 1200 mm center to center and cross “T” of size 24x25 mm made of 0.30 mm thick (minimum) sheet, 1200 mm long spaced between main “T” at 600 mm center to center to form a grid of 1200x600 mm and secondary cross “T” of length 600 mm and size 24x25 mm made of 0.30 mm thick (minimum) sheet to be interlocked at middle of the 1200x600 mm panel to form grids of 600x600 mm and wall angle of size 24x24x0.3 mm and laying false ceiling tiles of approved texture in the grid including required cutting/making, opening for services like diffusers, grills, light fittings, fixtures, smoke detectors etc. Main “T” runners to be suspended from ceiling using GI slotted cleats of size 27 x 37 x 25 x 1.6 mm fixed to ceiling with 12.5 mm dia and 50 mm long dash fasteners, 4 mm GI adjustable rods with galvanised butterfly level clips of size 85 x 30 x 0.8 mm spaced at 1200 mm center to center along main T, bottom exposed width of 24 mm of all T-sections shall be pre-painted with polyester paint, all complete for all heights as per specifications, drawings and as directed by Engineer-in-charge. |
| 88 | Supplying, fabricating and fixing aluminium work for fixed portions of panel-room partitions using approved extruded built-up tubular/Z sections conforming to IS:733 and IS:1285, powder coated with minimum 50 micron coating. The work shall include mitring, mechanical jointing, cleat angles, aluminium snap beads, EPDM/neoprene gaskets, CP brass/SS screws, dash-fastener provisions and all necessary accessories for a rigid and accurately aligned frame. Glazing/paneling and dash fasteners shall be measured and paid separately as applicable; the completed frame shall be checked for plumb, level, alignment and secure fixing. |
| 89 | Supplying, fabricating and fixing powder-coated aluminium shutter for panel-room door, window or ventilator using approved extruded tubular/Z sections conforming to IS:733 and IS:1285, with minimum 50 micron powder coating. The item shall include hinges/pivots, EPDM/neoprene gaskets, provision for hardware, mechanical joints, cleats, screws and all necessary accessories for complete shutter fabrication and fixing. The shutter shall be aligned, adjusted and tested for smooth opening, closing and proper seating; fittings shall be paid separately where specified. |
| 90 | Supplying and fixing 12 mm thick pre-laminated particle board conforming to IS:12823 Grade I Type II, with decorative lamination on both sides, fixed within aluminium panel-room partition/door frames. The work shall include cutting to required size, edge treatment, CP brass/SS screws and all necessary fixing accessories. Panels shall be neatly aligned with uniform joints and securely fixed, with all exposed edges finished cleanly. |
| 91 | Supplying and fixing 4 mm thick float glass glazing in aluminium panel-room partitions, doors and fixed panels, complete with EPDM/neoprene gasket and all necessary glazing accessories. The glass shall be accurately cut, fitted and secured within aluminium snap-beaded frames without cracks, chips or excessive clearance. The completed glazing shall be checked for proper seating, uniform appearance and safe fixing. |
| 92 | Supplying and fixing 5 mm thick float glass glazing in aluminium panel-room partitions, doors and fixed panels, complete with EPDM/neoprene gasket and all necessary glazing accessories. The glass shall be accurately cut, fitted and secured within aluminium snap-beaded frames without cracks, chips or excessive clearance. The completed glazing shall be checked for proper seating, uniform appearance and safe fixing. |
| 93 | Supplying and fixing 8 mm thick float glass glazing in aluminium panel-room partitions, doors and fixed panels, complete with EPDM/neoprene gasket and all necessary glazing accessories. The glass shall be accurately cut, fitted and secured within aluminium snap-beaded frames without cracks, chips or excessive clearance. The completed glazing shall be checked for proper seating, uniform appearance and safe fixing. |
| 94 | Supplying, fixing and commissioning double-action hydraulic floor spring conforming to IS:6315, suitable for aluminium panel-room door shutters up to 125 kg, with brass cover plate of minimum 1.25 mm thickness. The work shall include floor cutting, embedding, brass pivot, outer box, slide plate and all fixing accessories. The door shall be adjusted and tested for smooth double-action operation, controlled closing and proper alignment, with the floor finish made good after installation. |
| 95 | Supplying and fixing 32 mm outside diameter, 3.0 mm thick and 2100 mm long anodised/ powder-coated/ polyester powder-coated aluminium tubular pull handle for panel-room door, complete with stainless-steel screws and required fixing accessories. The handle shall be securely anchored to the shutter at the approved locations with suitable backing/support. The completed handle shall be checked for rigidity, alignment, smooth edges and secure fixing. |
| 96 | Supplying and fixing brass 100 mm mortice latch and lock with six levers, without pair of handles, of approved make for aluminium panel-room doors, including necessary cutting and making good. The item shall include lock body, cylinder/key arrangement as applicable, screws, fixing accessories and adjustment. The lock shall be tested for smooth key operation, positive latching, proper engagement and secure locking of the door. |
| 97 | Supplying and fixing anodised/ powder-coated/ polyester powder-coated aluminium casement window fastener of required length for aluminium panel-room windows, complete with necessary stainless-steel/approved screws and accessories. The fastener shall be securely fixed and adjusted to provide positive locking of the window shutter. The completed assembly shall be tested for smooth operation, secure engagement and proper alignment. |
| 98 | Supplying and applying weather/structural non-sag elastomeric PU sealant over approved backer rod at the interface between aluminium partition frames and adjacent RCC, brick, stone, ceramic or gypsum surfaces, for joints up to 5 mm depth and 5 mm width, complying with ASTM C920, DIN 18540-F and ISO 11600. The work shall include cleaning and preparation of joint surfaces, primer where recommended, backer rod, sealant application and tooling to form a neat continuous seal. The completed joint shall be free from gaps, voids and discontinuities and shall be inspected for proper adhesion and weather-tightness. |
| 99 | Supplying and applying weather/structural non-sag elastomeric PU sealant over approved backer rod at the interface between aluminium partition frames and adjacent RCC, brick, stone, ceramic or gypsum surfaces, for joints above depth of 5 mm to 10 mm depth and width of 5 mm to 10 mm, complying with ASTM C920, DIN 18540-F and ISO 11600. The work shall include cleaning and preparation of joint surfaces, primer where recommended, backer rod, sealant application and tooling to form a neat continuous seal. The completed joint shall be free from gaps, voids and discontinuities and shall be inspected for proper adhesion and weather-tightness. |
| 100 | Supplying and applying weather/structural non-sag elastomeric PU sealant over approved backer rod at the interface between aluminium partition frames and adjacent RCC, brick, stone, ceramic or gypsum surfaces, for joints above depth of 10 mm to 20 mm depth and and width of 10 mm to 20 mm, complying with ASTM C920, DIN 18540-F and ISO 11600. The work shall include cleaning and preparation of joint surfaces, primer where recommended, backer rod, sealant application and tooling to form a neat continuous seal. The completed joint shall be free from gaps, voids and discontinuities and shall be inspected for proper adhesion and weather-tightness. |
| 101 | Providing and laying dry lean cement concrete sub-base over prepared sub-grade using coarse and fine aggregates conforming to IS:383, with aggregate-cement ratio not exceeding 15:1 and cement content not less than 150 kg/cum. The work shall include batching, transportation, mechanical paving, compaction with 8–10 tonne vibratory roller, finishing and curing. The completed DLC shall be checked for thickness, levels, strength and surface regularity. |
| 102 | Providing and fixing factory-made solid core flush door shutter, 35 mm thick, conforming to IS 2202 (Part-I), with face veneers of approved quality, hardwood lipping on all edges, including rebating where required, fixing with approved quality M.S./SS butt hinges with necessary screws, cutting, fitting and fixing complete in all respects as directed by Engineer-in-Charge. |
| 103 | Providing and fixing factory-made PVC door set for toilet/washroom, comprising PVC door frame/chowkhat of approved size and section and minimum 25 mm thick PVC door shutter, made from rigid, waterproof, termite-proof PVC material of approved make, colour and finish, including cutting, fitting and fixing of frame to masonry opening with suitable fasteners, filling/packing of gaps with approved material, fixing of shutter with stainless steel/MS hinges, SS/PVC lever handle, tower bolt/latch, mortice/appropriate toilet lock, door stopper and all necessary screws, fasteners, fittings and accessories, including making good the adjoining surfaces and complete installation in all respects as directed by the Engineer-in-Charge. |
| 104 | Providing and fixing complete WPC door assembly, comprising factory-made WPC solid door frame/chowkhat of approved section and 35 mm thick WPC solid plain flush door shutter, including cutting, mitring, jointing, fixing to wall/opening with suitable fasteners, SS/M.S. butt hinges, screws, necessary hardware, sealant, making good and all labour, materials, tools and tackles, complete as directed by Engineer-in-Charge. |
| 105 | Providing, supplying and fixing factory-made galvanized iron (GI) rolling shutter of approved make, manufactured from cold-rolled galvanized steel laths of minimum 80 mm width and 1.20 mm thickness, interlocked with each other throughout their length and secured at ends with end locks, complete with galvanized steel top cover, specially designed galvanized/M.S. pipe shaft, brackets, side guides/channels, bottom rail with suitable angle/flat, high tensile steel wire springs, ball bearings, locking arrangement for operation from inside and outside, pull-and-push manual operating arrangement, including cutting, fabrication, drilling, welding where required, hoisting, fixing in position, alignment, leveling, anchoring to masonry/RCC/structural steel, necessary nuts, bolts, screws, fasteners and all other accessories, applying approved protective coating/primer to non-galvanized portions, and making good the adjoining surfaces, complete in all respects as directed by the Engineer-in-Charge. |
| 106 | Providing and fixing M.S. grills of required pattern in frames of windows etc. with M.S. flats, square or round bars etc., including priming coat with approved steel primer and 2 coat paint, all complete — fixed to steel windows by welding /fixed to openings/wooden frames with rawl plugs, screws etc. |
| 107 | Providing and fixing wooden door frame/chowkhat, of approved section and size, properly seasoned and treated, wrought framed, rebated, tenoned and mortised, including providing and fixing holdfasts/dash fasteners, packing with cement mortar/concrete, cutting, fitting and fixing complete as directed by Engineer-in-Charge. |
| 108 | “Providing, supplying and fixing 6 mm thick M.S. chequered plate of approved quality for flooring/treads/landings/platforms, including cutting to required size, welding/fixing to supporting steel members, necessary edge preparation, hoisting, handling and applying one coat of approved steel primer, complete as directed by Engineer-in-Charge.” |
| 109 | Providing and applying road surface marking with ready-mixed road marking paint conforming to IS:164 on new bituminous/concrete surfaces, including cleaning, setting out, masking and application of two or more coats to obtain a uniform finish. The work shall include all labour, materials and tools necessary for sharp and clearly visible markings. Completed markings shall be checked for width, alignment, coverage and uniformity. |
| 110 | Providing and laying factory-made M-25 grade cement concrete kerb stones at or near ground level to required line, level and curvature, jointed with cement mortar 1:3. The work shall include preparation, placement, joint finishing and drainage openings wherever required. Finished kerb edging shall be aligned, securely seated and checked for uniformity, curvature and proper drainage. |
| 111 | Providing and laying factory-made 60 mm thick M-30 grade cement concrete interlocking paver blocks of approved size, shape, colour and pattern over 50 mm thick compacted sand bed. The work shall include cutting, fitting, vibratory compaction, joint filling with fine sand and final sweeping. The completed paved surface shall be checked for levels, slope, interlocking, joint filling and surface regularity. |
| 112 | Providing, casting and fixing precast reinforced cement concrete covers/slabs of specified size and minimum 75 mm thickness, using cement concrete of grade M-25, including reinforcement with TMT steel bars of required diameter and spacing, centering/moulds, vibration, finishing, curing, lifting, loading, transportation, handling and placing in position over drain/inspection chamber/cable trench, including making provision for lifting hooks/holes wherever required, complete in all respects as directed by the Engineer-in-Charge. |
| 113 | Providing brick edging in full-brick width and half-brick depth along road/footpath edges, including excavation, laying, alignment, refilling and disposal of surplus earth within 50 m lead. Bricks shall be properly bedded and jointed to form a continuous edge restraint. The completed edging shall be checked for line, level, stability and interface with the pavement. |
| 114 | Providing, laying and jointing 200 mm diameter glazed stoneware pipe, Class SP-1, with stiff 1:1 cement mortar joints, including cutting, bedding, alignment and testing of joints. The work shall include all necessary labour, tools and minor accessories for complete installation. The pipeline shall be checked for line, level, gradient, joint tightness and leakage before backfilling. |
| 115 | Providing, laying and jointing 300 mm diameter glazed stoneware pipe, Class SP-1, with stiff 1:1 cement mortar joints, including cutting, bedding, alignment and testing of joints. The work shall include all necessary labour, tools and minor accessories for complete installation. The pipeline shall be checked for line, level, gradient, joint tightness and leakage before backfilling. |
| 116 | Providing and laying cement concrete 1:5:10 using 40 mm aggregate all around 150 mm diameter stoneware pipe, including bed concrete as per standard design. The work shall include preparation of trench bottom, placing and compacting concrete, maintaining pipe alignment and curing. The completed bedding/encasement shall provide uniform support without displacement of the pipe. |
| 117 | Providing and laying cement concrete 1:5:10 up to haunches of 150 mm diameter stoneware pipe including bed concrete as per standard design. The work shall include careful placement around the pipe, compaction without damaging joints and curing. Pipe line and gradient shall be rechecked before and after concrete placement. |
| 118 | Constructing brick masonry manhole of internal size 900 x 800 mm and 450 mm deep in cement mortar 1:4, including RCC top slab, foundation concrete 1:4:8, 12 mm internal plaster in 1:3 mortar, cement-finished channels in 1:2:4 concrete and light-duty CI cover/frame 455 x 610 mm. The item shall include all masonry, concrete, plaster, channel formation and finishing required for complete construction. The completed manhole shall be watertight, properly benched, aligned with connecting drains and provided with accessible cover. |
| 119 | Supplying and fixing 560 mm diameter heavy-duty CI manhole cover without frame, with minimum cover weight of 108 kg, suitable for industrial road/yard drainage applications. The item shall include seating, levelling and all necessary fixing/packing materials. The cover shall be securely seated, flush with finished pavement level and checked for stability and safe operation. |
| 120 | Providing and laying Non-Pressure NP-3 class medium-duty RCC pipe of 450 mm diameter including collars/spigot joints with stiff 1:2 cement mortar and testing of joints. The work shall include bedding, alignment, jointing and all necessary handling and installation accessories. The completed pipeline shall be checked for gradient, invert level, joint integrity and free flow before backfilling. |
| 121 | Providing and laying Non-Pressure NP-3 class medium-duty RCC pipe of 600 mm diameter including collars/spigot joints with stiff 1:2 cement mortar and testing of joints. The work shall include bedding, alignment, jointing and all necessary handling and installation accessories. The completed pipeline shall be checked for gradient, invert level, joint integrity and free flow before backfilling. |
| 122 | Constructing soak pit 1.20 x 1.20 x 1.20 m filled with brickbats including 100 mm diameter, 1.20 m long stoneware drain pipe and all associated work as per standard design. The item shall include excavation, filling, pipe connection and making good. The completed soak pit shall be checked for stability, inlet level and free discharge into the percolation zone. |
| 123 | Supplying and fixing 100 mm diameter stoneware intercepting trap in manholes using stiff 1:1 cement mortar, including all necessary joints, bedding, alignment and testing. The trap shall be installed at designed invert level and securely connected to incoming/outgoing drainage lines. The completed installation shall be tested for leakage, flow and proper trap operation. |
| 124 | Making bell-mouth opening/entrance of 100 x 50 x 50 cm for drainage pipe under footpath, including cement concrete 1:3:6, plastering, precast RCC/SFRC slab, cement-mortar finishing, centering, shuttering and neat cement punning inside the bell mouth. The work shall include complete shaping and integration with adjoining road/footpath. The completed opening shall be aligned with the drain inlet and finished to prevent water stagnation. |
| 125 | Supplying, fixing and installing white vitreous china Orissa-pattern Indian WC pan of 580 x 440 mm size, complete with integral foot rests, 100 mm P/S trap, 10-litre low-level PVC flushing cistern, flush pipe and operating fittings. The item shall include all necessary brackets, connectors, washers, sealing materials, clamps and fixing accessories required for a complete installation. The work shall include connection to the water-supply and soil/waste system, testing for leakage and proper flushing, and making good the adjoining surface. |
| 126 | Supplying, fixing and installing white vitreous china European WC complete with solid seat and lid, 10-litre low-level vitreous china flushing cistern, CP flush bend, brackets, overflow arrangement and mosquito-proof coupling. The item shall include all necessary fittings, connectors, washers, seals and fixing accessories for a complete and functional installation. The work shall include connection to water-supply and soil/waste piping, testing of flushing and leakage, and making good the installation area. |
| 127 | Supplying, fixing and installing white vitreous china flat-back wash basin of 630 x 450 mm size, complete with CI brackets, two 15 mm CP brass pillar taps and 32 mm CP brass waste fitting. The item shall include all necessary brackets, waste connections, flexible connections, washers, sealants and fixing hardware required for installation. The work shall include connection to water-supply and waste piping, testing for leakage and proper drainage, and making good the adjoining wall/floor surface. |
| 128 | Supplying, fixing and installing AISI 304 stainless-steel kitchen sink conforming to IS 13983, size 610 x 510 mm with 200 mm bowl depth, complete with CI brackets and 40 mm SS plug. The item shall include all necessary waste fittings, supports, sealants, clamps and fixing accessories required for a complete installation. The work shall include connection to water-supply and waste piping, testing for leakage and proper drainage, and making good the counter/wall/floor interface. |
| 129 | Supplying, fixing and installing 8 mm CP/SS health jet for European WC, complete with flexible tube up to 1 m long and SS triangular wall plate. The item shall include all necessary connectors, washers, wall fixing hardware and sealing materials required for a leak-free installation. The work shall include connection to the water-supply line, testing for leakage and spray operation, and making good the wall surface. |
| 130 | Supplying, fixing and installing a pair of white vitreous china foot rests for Indian squatting WC, each approximately 250 x 130 x 30 mm in size. The item shall include all necessary fixing materials, supports and accessories required for firm and level installation. The work shall include proper alignment with the WC pan, secure anchoring to the floor and making good the surrounding surface. |
| 131 | Supplying, fixing and installing 10-litre white PVC low-level flushing cistern complete with manually operated handle/lever and internal flushing fittings. The item shall include inlet valve, float assembly, flush valve, washers, connectors, flush pipe and all fixing accessories required for complete installation. The work shall include connection to the water-supply and WC pan, adjustment of the flushing mechanism, testing for leakage and proper flushing, and making good the wall surface. |
| 132 | Supplying, fixing and installing 10-litre white vitreous china low-level flushing cistern complete with controlled flushing mechanism and all internal fittings. The item shall include inlet valve, float arrangement, flush valve, connectors, flush pipe, washers and fixing hardware required for complete installation. The work shall include connection to the water-supply and WC pan, adjustment and testing of the flushing system for satisfactory operation and leakage-free performance, and making good the installation area. |
| 133 | Supplying, fixing and installing white solid-plastic WC seat and lid suitable for the specified pedestal WC pan, complete with hinges, buffers and fixing hardware. The item shall include all brackets, fasteners and accessories required for secure and aligned installation. The work shall include adjustment of the seat and lid for smooth operation, checking of stability and proper seating, and complete making good of the installation. |
| 134 | Supplying, fixing and connecting GI inlet connection for WC flush pipe, including cutting, threading and necessary fittings. The item shall include nipples, unions, washers, sealants and other accessories required for a leak-proof connection. The work shall include connection to the flushing cistern/WC arrangement, pressure testing for leakage and making good of the surrounding surface. |
| 135 | Supplying, fixing and installing 32 mm CP brass bottle trap of approved make and quality, complete with all necessary connections. The item shall include washers, nuts, seals, connectors and fixing accessories required for a complete waste connection. The work shall include connection to the wash basin/sink waste outlet and drainage pipe, testing for leakage and free discharge, and making good the adjoining surface. |
| 136 | Supplying, fixing and installing white vitreous china wall-mounted/flat-back lipped-front urinal basin of approved size and pattern, complete with fixing accessories. The item shall include necessary brackets, flushing-water connection, waste fitting, trap, connectors, washers and sealants required for complete installation. The work shall include connection to the water-supply and drainage system, testing for flushing, leakage and proper discharge, and making good the wall surface. |
| 137 | Supplying, fixing and installing white vitreous china squatting plate urinal with integral rim and longitudinal flushing pipe, complete with necessary fittings. The item shall include brackets, flushing connections, waste/trap connections, washers, sealants and fixing accessories required for complete installation. The work shall include connection to water-supply and drainage piping, testing of flushing and drainage performance, and making good the floor/wall surfaces. |
| 138 | Supplying, fixing and connecting 32 mm semi-rigid PVC waste pipe for wash basin/sink, including compatible PVC waste fittings and all accessories required for complete installation. The item shall include couplers, bends, connectors, washers, solvent/jointing materials and clamps as necessary. The work shall include connection between the sanitary fixture and drainage line, testing for leakage and free flow, and making good the adjoining surface. |
| 139 | Supplying, fixing and connecting 32 mm flexible PVC waste pipe for wash basin, including compatible PVC waste fittings and all necessary accessories. The item shall include connectors, clamps, washers, sealing materials and fixing hardware required for complete installation. The work shall include connection to the waste outlet and drainage system, testing for leakage and unobstructed discharge, and making good the surrounding surface. |
| 140 | Supplying, fixing and connecting 40 mm flexible PVC waste pipe for sink/urinal, including compatible PVC waste fittings and all necessary accessories. The item shall include connectors, clamps, washers, sealing materials and fixing hardware required for complete installation. The work shall include connection to the sanitary fixture and drainage line, testing for leakage and free discharge, and making good the adjoining surface. |
| 141 | Supplying, fixing and installing 100 mm sand-cast iron grating for gully trap, complete with fixing accessories. The item shall include frame/support, clamps, cement mortar or other approved fixing material and all minor accessories required for proper installation. The work shall include accurate alignment with the gully trap, secure fixing, checking for free drainage and making good the surrounding surface. |
| 142 | Supplying, fixing and installing 25 mm mosquito-proof coupling of approved municipal design, complete with all necessary fittings. The item shall include connectors, sealants, washers and fixing accessories required for a secure and hygienic connection. The work shall include connection to the relevant sanitary/drainage arrangement, checking for leakage and mosquito-proof sealing, and making good the installation area. |
| 143 | Supplying, fixing and installing 600 x 450 mm bevelled-edge 6 mm superior-quality glass mirror with hardboard backing, wooden cleats and CP brass screws/washers. The item shall include all necessary brackets, supports, fasteners, protective backing and accessories required for secure installation. The work shall include accurate leveling and alignment, firm fixing without damage to the mirror, and complete finishing of the adjoining wall surface. |
| 144 | Supplying, fixing and installing 600 x 120 x 5 mm glass shelf with rounded edges, anodised aluminium angle frame, CP brass brackets and guard rail. The item shall include all necessary supports, screws, plugs, brackets and fixing accessories required for a stable installation. The work shall include accurate leveling, secure anchoring to the wall, checking for stability and making good the fixing points. |
| 145 | Supplying, fixing and installing CP brass toilet-paper holder of approved pattern, complete with necessary concealed/open fixing hardware. The item shall include screws, plugs, brackets and other minor accessories required for secure installation. The work shall include proper alignment and firm fixing to the wall, checking for smooth operation and making good the fixing surface. |
| 146 | Supplying, fixing and installing vitreous china toilet-paper holder of approved pattern, complete with all necessary fixing accessories. The item shall include brackets, screws, plugs, sealants and other minor accessories required for secure installation. The work shall include proper alignment, firm fixing to the wall and making good the surrounding surface. |
| 147 | Supplying, fixing and installing self-cleansing sand-cast iron trap with 100 mm inlet and 75 mm outlet, complete with grating and vent arrangement as required. The item shall include all necessary collars, connectors, cement mortar, sealants and fixing accessories required for a complete installation. The work shall include connection to the drainage system, testing for water-tightness and free discharge, and making good the surrounding floor/wall. |
| 148 | Supplying, fixing and installing PTMT waste coupling for wash basin/sink, 31 mm diameter, complete with all necessary washers, nuts, seals and connection accessories. The item shall be securely connected to the sanitary fixture and waste pipe to ensure a leak-free joint. The work shall include testing for leakage and proper discharge and making good the installation as required. |
| 149 | Supplying, fixing and installing PTMT trapezoidal towel ring of approximately 215 x 200 mm size with concealed fixing arrangement. The item shall include all necessary brackets, screws, plugs and concealed fixing accessories required for secure installation. The work shall include accurate alignment, firm fixing and making good the wall surface. |
| 150 | Supplying, fixing and installing 600 mm long PTMT towel rail complete with brackets and concealed fixing arrangement. The item shall include screws, plugs, supports and all other minor fixing accessories required for secure installation. The work shall include accurate leveling, firm anchoring to the wall and making good the fixing points. |
| 151 | Supplying, fixing and installing PTMT shelf approximately 440 x 124 x 36 mm, of approved quality and colour, complete with fixing accessories. The item shall include brackets, screws, wall plugs and other minor hardware required for secure installation. The work shall include accurate leveling and alignment, firm fixing and making good the adjoining wall surface. |
| 152 | Supplying, fixing and installing PTMT 15 mm urinal spreader complete with 1/2-inch BSP threaded connection. The item shall include all necessary connectors, washers, sealants and fixing accessories required for a complete installation. The work shall include connection to the urinal flushing line, testing for leakage and uniform water distribution, and making good the surrounding surface. |
| 153 | Supplying, fixing and installing PTMT urinal cock of 15 mm bore with BSP female threaded connection, complete with accessories. The item shall include connectors, washers, sealants and fixing hardware required for a leak-free connection. The work shall include connection to the urinal water-supply line, testing for leakage and operation, and making good the installation area. |
| 154 | Supplying, fixing and installing cPVC pressure pipe for hot/cold water supply, 15 mm OD, internal work exposed on wall, including CPVC plain/brass threaded fittings, clamps at 1 m spacing, solvent-cement joints and testing., complete with all necessary fittings, joints, clamps, connectors, washers, sealants and fixing accessories required for a complete installation. The work shall include all cutting, threading/jointing, supports, connections and minor accessories necessary for proper integration with the water-supply system. The completed installation shall be tested for leakage and satisfactory operation at the required pressure, including making good all disturbed surfaces and leaving the work complete in all respects. |
| 155 | Supplying, fixing and installing cPVC pressure pipe for hot/cold water supply, 20 mm OD, internal work exposed on wall, including fittings, clamps, jointing and testing complete., complete with all necessary fittings, joints, clamps, connectors, washers, sealants and fixing accessories required for a complete installation. The work shall include all cutting, threading/jointing, supports, connections and minor accessories necessary for proper integration with the water-supply system. The completed installation shall be tested for leakage and satisfactory operation at the required pressure, including making good all disturbed surfaces and leaving the work complete in all respects. |
| 156 | Supplying, fixing and installing cPVC pressure pipe for hot/cold water supply, 25 mm OD, internal work exposed on wall, including fittings, clamps, jointing and testing complete., complete with all necessary fittings, joints, clamps, connectors, washers, sealants and fixing accessories required for a complete installation. The work shall include all cutting, threading/jointing, supports, connections and minor accessories necessary for proper integration with the water-supply system. The completed installation shall be tested for leakage and satisfactory operation at the required pressure, including making good all disturbed surfaces and leaving the work complete in all respects. |
| 157 | Supplying, fixing and installing cPVC pressure pipe for hot/cold water supply, 32 mm OD, internal work exposed on wall, including fittings, clamps, jointing and testing complete., complete with all necessary fittings, joints, clamps, connectors, washers, sealants and fixing accessories required for a complete installation. The work shall include all cutting, threading/jointing, supports, connections and minor accessories necessary for proper integration with the water-supply system. The completed installation shall be tested for leakage and satisfactory operation at the required pressure, including making good all disturbed surfaces and leaving the work complete in all respects. |
| 158 | Supplying, fixing and installing cPVC pressure pipe for hot/cold water supply, 40 mm OD, internal work exposed on wall, including fittings, clamps, jointing and testing complete., complete with all necessary fittings, joints, clamps, connectors, washers, sealants and fixing accessories required for a complete installation. The work shall include all cutting, threading/jointing, supports, connections and minor accessories necessary for proper integration with the water-supply system. The completed installation shall be tested for leakage and satisfactory operation at the required pressure, including making good all disturbed surfaces and leaving the work complete in all respects. |
| 159 | Supplying, fixing and installing cPVC pressure pipe for hot/cold water supply, 50 mm OD, internal work exposed on wall, including fittings, clamps, jointing and testing complete., complete with all necessary fittings, joints, clamps, connectors, washers, sealants and fixing accessories required for a complete installation. The work shall include all cutting, threading/jointing, supports, connections and minor accessories necessary for proper integration with the water-supply system. The completed installation shall be tested for leakage and satisfactory operation at the required pressure, including making good all disturbed surfaces and leaving the work complete in all respects. |
| 160 | Supplying, fixing and installing cPVC pressure pipe for hot/cold water supply, 15 mm OD, concealed internal work including cutting chases, making good, fittings, clamps, solvent-cement joints and testing., complete with all necessary fittings, joints, clamps, connectors, washers, sealants and fixing accessories required for a complete installation. The work shall include all cutting, threading/jointing, supports, connections and minor accessories necessary for proper integration with the water-supply system. The completed installation shall be tested for leakage and satisfactory operation at the required pressure, including making good all disturbed surfaces and leaving the work complete in all respects. |
| 161 | Supplying, fixing and installing cPVC pressure pipe for hot/cold water supply, 20 mm OD, concealed internal work including cutting chases, making good, fittings, clamps, jointing and testing., complete with all necessary fittings, joints, clamps, connectors, washers, sealants and fixing accessories required for a complete installation. The work shall include all cutting, threading/jointing, supports, connections and minor accessories necessary for proper integration with the water-supply system. The completed installation shall be tested for leakage and satisfactory operation at the required pressure, including making good all disturbed surfaces and leaving the work complete in all respects. |
| 162 | Supplying, fixing and installing cPVC pressure pipe for hot/cold water supply, 25 mm OD, concealed internal work including cutting chases, making good, fittings, clamps, jointing and testing., complete with all necessary fittings, joints, clamps, connectors, washers, sealants and fixing accessories required for a complete installation. The work shall include all cutting, threading/jointing, supports, connections and minor accessories necessary for proper integration with the water-supply system. The completed installation shall be tested for leakage and satisfactory operation at the required pressure, including making good all disturbed surfaces and leaving the work complete in all respects. |
| 163 | Supplying, fixing and installing cPVC pressure pipe for hot/cold water supply, 32 mm OD, concealed internal work including cutting chases, making good, fittings, clamps, jointing and testing., complete with all necessary fittings, joints, clamps, connectors, washers, sealants and fixing accessories required for a complete installation. The work shall include all cutting, threading/jointing, supports, connections and minor accessories necessary for proper integration with the water-supply system. The completed installation shall be tested for leakage and satisfactory operation at the required pressure, including making good all disturbed surfaces and leaving the work complete in all respects. |
| 164 | Supplying, fixing and installing cPVC pressure pipe for hot/cold water supply, 15 mm OD, external work including CPVC fittings, trenching/refilling, solvent-cement joints and testing., complete with all necessary fittings, joints, clamps, connectors, washers, sealants and fixing accessories required for a complete installation. The work shall include all cutting, threading/jointing, supports, connections and minor accessories necessary for proper integration with the water-supply system. The completed installation shall be tested for leakage and satisfactory operation at the required pressure, including making good all disturbed surfaces and leaving the work complete in all respects. |
| 165 | Supplying, fixing and installing cPVC pressure pipe for hot/cold water supply, 20 mm OD, external work including fittings, trenching/refilling, jointing and testing., complete with all necessary fittings, joints, clamps, connectors, washers, sealants and fixing accessories required for a complete installation. The work shall include all cutting, threading/jointing, supports, connections and minor accessories necessary for proper integration with the water-supply system. The completed installation shall be tested for leakage and satisfactory operation at the required pressure, including making good all disturbed surfaces and leaving the work complete in all respects. |
| 166 | Supplying, fixing and installing cPVC pressure pipe for hot/cold water supply, 25 mm OD, external work including fittings, trenching/refilling, jointing and testing., complete with all necessary fittings, joints, clamps, connectors, washers, sealants and fixing accessories required for a complete installation. The work shall include all cutting, threading/jointing, supports, connections and minor accessories necessary for proper integration with the water-supply system. The completed installation shall be tested for leakage and satisfactory operation at the required pressure, including making good all disturbed surfaces and leaving the work complete in all respects. |
| 167 | Supplying, fixing and installing cPVC pressure pipe for hot/cold water supply, 32 mm OD, external work including fittings, trenching/refilling, jointing and testing., complete with all necessary fittings, joints, clamps, connectors, washers, sealants and fixing accessories required for a complete installation. The work shall include all cutting, threading/jointing, supports, connections and minor accessories necessary for proper integration with the water-supply system. The completed installation shall be tested for leakage and satisfactory operation at the required pressure, including making good all disturbed surfaces and leaving the work complete in all respects. |
| 168 | Supplying, fixing and installing cPVC pressure pipe for hot/cold water supply, 40 mm OD, external work including fittings, trenching/refilling, jointing and testing., complete with all necessary fittings, joints, clamps, connectors, washers, sealants and fixing accessories required for a complete installation. The work shall include all cutting, threading/jointing, supports, connections and minor accessories necessary for proper integration with the water-supply system. The completed installation shall be tested for leakage and satisfactory operation at the required pressure, including making good all disturbed surfaces and leaving the work complete in all respects. |
| 169 | Supplying, fixing and installing cPVC pressure pipe for hot/cold water supply, 50 mm OD, external work including fittings, trenching/refilling, jointing and testing., complete with all necessary fittings, joints, clamps, connectors, washers, sealants and fixing accessories required for a complete installation. The work shall include all cutting, threading/jointing, supports, connections and minor accessories necessary for proper integration with the water-supply system. The completed installation shall be tested for leakage and satisfactory operation at the required pressure, including making good all disturbed surfaces and leaving the work complete in all respects. |
| 170 | Supplying, fixing and installing unplasticised PVC flexible connection pipe with brass unions, 15 mm bore, 30 cm long, complete., complete with all necessary fittings, joints, clamps, connectors, washers, sealants and fixing accessories required for a complete installation. The work shall include all cutting, threading/jointing, supports, connections and minor accessories necessary for proper integration with the water-supply system. The completed installation shall be tested for leakage and satisfactory operation at the required pressure, including making good all disturbed surfaces and leaving the work complete in all respects. |
| 171 | Supplying, fixing and installing unplasticised PVC flexible connection pipe with brass unions, 15 mm bore, 45 cm long, complete., complete with all necessary fittings, joints, clamps, connectors, washers, sealants and fixing accessories required for a complete installation. The work shall include all cutting, threading/jointing, supports, connections and minor accessories necessary for proper integration with the water-supply system. The completed installation shall be tested for leakage and satisfactory operation at the required pressure, including making good all disturbed surfaces and leaving the work complete in all respects. |
| 172 | Supplying, fixing and installing cP brass shower rose, 100 mm diameter, suitable for 15/20 mm inlet, complete with fixing., complete with all necessary fittings, joints, clamps, connectors, washers, sealants and fixing accessories required for a complete installation. The work shall include all cutting, threading/jointing, supports, connections and minor accessories necessary for proper integration with the water-supply system. The completed installation shall be tested for leakage and satisfactory operation at the required pressure, including making good all disturbed surfaces and leaving the work complete in all respects. |
| 173 | Supplying, fixing and installing cP brass shower rose, 150 mm diameter, suitable for 15/20 mm inlet, complete with fixing., complete with all necessary fittings, joints, clamps, connectors, washers, sealants and fixing accessories required for a complete installation. The work shall include all cutting, threading/jointing, supports, connections and minor accessories necessary for proper integration with the water-supply system. The completed installation shall be tested for leakage and satisfactory operation at the required pressure, including making good all disturbed surfaces and leaving the work complete in all respects. |
| 174 | Supplying, fixing and installing polyethylene water-storage tank conforming to IS 12701, with cover and locking arrangement and holes for inlet/outlet/overflow; excluding fittings and base support., complete with all necessary fittings, joints, clamps, connectors, washers, sealants and fixing accessories required for a complete installation. The work shall include all cutting, threading/jointing, supports, connections and minor accessories necessary for proper integration with the water-supply system. The completed installation shall be tested for leakage and satisfactory operation at the required pressure, including making good all disturbed surfaces and leaving the work complete in all respects. |
| 175 | Supplying, fixing and installing cP brass bib cock, 15 mm nominal bore, approved quality conforming to IS 8931, complete., complete with all necessary fittings, joints, clamps, connectors, washers, sealants and fixing accessories required for a complete installation. The work shall include all cutting, threading/jointing, supports, connections and minor accessories necessary for proper integration with the water-supply system. The completed installation shall be tested for leakage and satisfactory operation at the required pressure, including making good all disturbed surfaces and leaving the work complete in all respects. |
| 176 | Supplying, fixing and installing cP brass long-nose bib cock, 15 mm nominal bore, minimum 810 g, complete., complete with all necessary fittings, joints, clamps, connectors, washers, sealants and fixing accessories required for a complete installation. The work shall include all cutting, threading/jointing, supports, connections and minor accessories necessary for proper integration with the water-supply system. The completed installation shall be tested for leakage and satisfactory operation at the required pressure, including making good all disturbed surfaces and leaving the work complete in all respects. |
| 177 | Supplying, fixing and installing cP brass long-body bib cock, 15 mm nominal bore, minimum 690 g, complete., complete with all necessary fittings, joints, clamps, connectors, washers, sealants and fixing accessories required for a complete installation. The work shall include all cutting, threading/jointing, supports, connections and minor accessories necessary for proper integration with the water-supply system. The completed installation shall be tested for leakage and satisfactory operation at the required pressure, including making good all disturbed surfaces and leaving the work complete in all respects. |
| 178 | Supplying, fixing and installing cP brass concealed stop cock, 15 mm nominal bore, standard approved design conforming to IS 8931, complete., complete with all necessary fittings, joints, clamps, connectors, washers, sealants and fixing accessories required for a complete installation. The work shall include all cutting, threading/jointing, supports, connections and minor accessories necessary for proper integration with the water-supply system. The completed installation shall be tested for leakage and satisfactory operation at the required pressure, including making good all disturbed surfaces and leaving the work complete in all respects. |
| 179 | Supplying, fixing and installing cP brass angle valve for basin mixer/geyser point, 15 mm nominal bore, conforming to IS 8931, complete., complete with all necessary fittings, joints, clamps, connectors, washers, sealants and fixing accessories required for a complete installation. The work shall include all cutting, threading/jointing, supports, connections and minor accessories necessary for proper integration with the water-supply system. The completed installation shall be tested for leakage and satisfactory operation at the required pressure, including making good all disturbed surfaces and leaving the work complete in all respects. |
| 180 | Supplying, fixing and installing cP brass extension nipple, 15mmx50 mm, approved make/quality, complete., complete with all necessary fittings, joints, clamps, connectors, washers, sealants and fixing accessories required for a complete installation. The work shall include all cutting, threading/jointing, supports, connections and minor accessories necessary for proper integration with the water-supply system. The completed installation shall be tested for leakage and satisfactory operation at the required pressure, including making good all disturbed surfaces and leaving the work complete in all respects. |
| 181 | Supplying, fixing and installing pTMT bib cock, 15 mm bore, 86 mm long, minimum 88 g, approved quality/colour, complete., complete with all necessary fittings, joints, clamps, connectors, washers, sealants and fixing accessories required for a complete installation. The work shall include all cutting, threading/jointing, supports, connections and minor accessories necessary for proper integration with the water-supply system. The completed installation shall be tested for leakage and satisfactory operation at the required pressure, including making good all disturbed surfaces and leaving the work complete in all respects. |
| 182 | Supplying, fixing and installing pTMT concealed stop cock, 15 mm bore, 108 mm long, minimum 108 g, complete., complete with all necessary fittings, joints, clamps, connectors, washers, sealants and fixing accessories required for a complete installation. The work shall include all cutting, threading/jointing, supports, connections and minor accessories necessary for proper integration with the water-supply system. The completed installation shall be tested for leakage and satisfactory operation at the required pressure, including making good all disturbed surfaces and leaving the work complete in all respects. |
| 183 | Supplying, fixing and installing pTMT pillar cock, 15 mm bore, 125 mm long with foam-flow outlet, minimum 120 g, complete., complete with all necessary fittings, joints, clamps, connectors, washers, sealants and fixing accessories required for a complete installation. The work shall include all cutting, threading/jointing, supports, connections and minor accessories necessary for proper integration with the water-supply system. The completed installation shall be tested for leakage and satisfactory operation at the required pressure, including making good all disturbed surfaces and leaving the work complete in all respects. |
| 184 | Supplying, fixing and installing pTMT push cock, 15 mm bore, 98 mm long, minimum 75 g, complete., complete with all necessary fittings, joints, clamps, connectors, washers, sealants and fixing accessories required for a complete installation. The work shall include all cutting, threading/jointing, supports, connections and minor accessories necessary for proper integration with the water-supply system. The completed installation shall be tested for leakage and satisfactory operation at the required pressure, including making good all disturbed surfaces and leaving the work complete in all respects. |
| 185 | Supplying, fixing and installing circular PTMT floor/waste grating, 100 mm nominal diameter, approved quality/colour, complete., complete with all necessary fittings, joints, clamps, connectors, washers, sealants and fixing accessories required for a complete installation. The work shall include all cutting, threading/jointing, supports, connections and minor accessories necessary for proper integration with the water-supply system. The completed installation shall be tested for leakage and satisfactory operation at the required pressure, including making good all disturbed surfaces and leaving the work complete in all respects. |
| 186 | Supplying, fixing and installing circular PTMT floor/waste grating, 125 mm nominal diameter with 25 mm waste hole, complete., complete with all necessary fittings, joints, clamps, connectors, washers, sealants and fixing accessories required for a complete installation. The work shall include all cutting, threading/jointing, supports, connections and minor accessories necessary for proper integration with the water-supply system. The completed installation shall be tested for leakage and satisfactory operation at the required pressure, including making good all disturbed surfaces and leaving the work complete in all respects. |
| 187 | Supplying, fixing and installing pTMT ball cock with epoxy-coated aluminium rod and plastic float, 15 mm bore, complete., complete with all necessary fittings, joints, clamps, connectors, washers, sealants and fixing accessories required for a complete installation. The work shall include all cutting, threading/jointing, supports, connections and minor accessories necessary for proper integration with the water-supply system. The completed installation shall be tested for leakage and satisfactory operation at the required pressure, including making good all disturbed surfaces and leaving the work complete in all respects. |
| 188 | Supplying, fixing and installing pTMT angle stop cock, 15 mm nominal bore, minimum 85 g, complete., complete with all necessary fittings, joints, clamps, connectors, washers, sealants and fixing accessories required for a complete installation. The work shall include all cutting, threading/jointing, supports, connections and minor accessories necessary for proper integration with the water-supply system. The completed installation shall be tested for leakage and satisfactory operation at the required pressure, including making good all disturbed surfaces and leaving the work complete in all respects. |
| 189 | Supplying, fixing and installing pTMT swivelling shower, 15 mm nominal bore, minimum 40 g, complete., complete with all necessary fittings, joints, clamps, connectors, washers, sealants and fixing accessories required for a complete installation. The work shall include all cutting, threading/jointing, supports, connections and minor accessories necessary for proper integration with the water-supply system. The completed installation shall be tested for leakage and satisfactory operation at the required pressure, including making good all disturbed surfaces and leaving the work complete in all respects. |
| 190 | Supplying, fixing and installing pTMT soap-dish holder, approx. 138x102x75 mm, concealed fixing arrangement, minimum 106 g, complete., complete with all necessary fittings, joints, clamps, connectors, washers, sealants and fixing accessories required for a complete installation. The work shall include all cutting, threading/jointing, supports, connections and minor accessories necessary for proper integration with the water-supply system. The completed installation shall be tested for leakage and satisfactory operation at the required pressure, including making good all disturbed surfaces and leaving the work complete in all respects. |
| 191 | Supplying, fixing and installing enclosed bulk water meter, 80 mm nominal bore, conforming to IS 2373, including bolts, nuts and rubber insertions; tail pieces excluded., complete with all necessary fittings, joints, clamps, connectors, washers, sealants and fixing accessories required for a complete installation. The work shall include all cutting, threading/jointing, supports, connections and minor accessories necessary for proper integration with the water-supply system. The completed installation shall be tested for leakage and satisfactory operation at the required pressure, including making good all disturbed surfaces and leaving the work complete in all respects. |
| 192 | Supplying, fixing and installing enclosed bulk water meter, 100 mm nominal bore, conforming to IS 2373, including bolts, nuts and rubber insertions; tail pieces excluded., complete with all necessary fittings, joints, clamps, connectors, washers, sealants and fixing accessories required for a complete installation. The work shall include all cutting, threading/jointing, supports, connections and minor accessories necessary for proper integration with the water-supply system. The completed installation shall be tested for leakage and satisfactory operation at the required pressure, including making good all disturbed surfaces and leaving the work complete in all respects. |
| 193 | Supplying, fixing and installing gI water-supply pipe, 15 mm nominal bore, internal exposed work, including GI fittings, clamps, cutting and making good walls, complete., complete with all necessary fittings, joints, clamps, connectors, washers, sealants and fixing accessories required for a complete installation. The work shall include all cutting, threading/jointing, supports, connections and minor accessories necessary for proper integration with the water-supply system. The completed installation shall be tested for leakage and satisfactory operation at the required pressure, including making good all disturbed surfaces and leaving the work complete in all respects. |
| 194 | Supplying, fixing and installing gI water-supply pipe, 20 mm nominal bore, internal exposed work, including GI fittings, clamps, cutting and making good walls, complete., complete with all necessary fittings, joints, clamps, connectors, washers, sealants and fixing accessories required for a complete installation. The work shall include all cutting, threading/jointing, supports, connections and minor accessories necessary for proper integration with the water-supply system. The completed installation shall be tested for leakage and satisfactory operation at the required pressure, including making good all disturbed surfaces and leaving the work complete in all respects. |
| 195 | Supplying, fixing and installing gI water-supply pipe, 25 mm nominal bore, internal exposed work, including GI fittings, clamps, cutting and making good walls, complete., complete with all necessary fittings, joints, clamps, connectors, washers, sealants and fixing accessories required for a complete installation. The work shall include all cutting, threading/jointing, supports, connections and minor accessories necessary for proper integration with the water-supply system. The completed installation shall be tested for leakage and satisfactory operation at the required pressure, including making good all disturbed surfaces and leaving the work complete in all respects. |
| 196 | Supplying, fixing and installing gI water-supply pipe, 15 mm nominal bore, concealed internal work, including GI fittings/clamps, anti-corrosive coating, cutting chases and making good, complete., complete with all necessary fittings, joints, clamps, connectors, washers, sealants and fixing accessories required for a complete installation. The work shall include all cutting, threading/jointing, supports, connections and minor accessories necessary for proper integration with the water-supply system. The completed installation shall be tested for leakage and satisfactory operation at the required pressure, including making good all disturbed surfaces and leaving the work complete in all respects. |
| 197 | Supplying, fixing and installing gI water-supply pipe, 20 mm nominal bore, concealed internal work, including GI fittings/clamps, anti-corrosive coating, cutting chases and making good, complete., complete with all necessary fittings, joints, clamps, connectors, washers, sealants and fixing accessories required for a complete installation. The work shall include all cutting, threading/jointing, supports, connections and minor accessories necessary for proper integration with the water-supply system. The completed installation shall be tested for leakage and satisfactory operation at the required pressure, including making good all disturbed surfaces and leaving the work complete in all respects. |
| 198 | Supplying, fixing and installing gI water-supply pipe, 15 mm nominal bore, external work, including GI fittings, trenching, refilling and testing, complete., complete with all necessary fittings, joints, clamps, connectors, washers, sealants and fixing accessories required for a complete installation. The work shall include all cutting, threading/jointing, supports, connections and minor accessories necessary for proper integration with the water-supply system. The completed installation shall be tested for leakage and satisfactory operation at the required pressure, including making good all disturbed surfaces and leaving the work complete in all respects. |
| 199 | Supplying, fixing and installing gI water-supply pipe, 20 mm nominal bore, external work, including GI fittings, trenching, refilling and testing, complete., complete with all necessary fittings, joints, clamps, connectors, washers, sealants and fixing accessories required for a complete installation. The work shall include all cutting, threading/jointing, supports, connections and minor accessories necessary for proper integration with the water-supply system. The completed installation shall be tested for leakage and satisfactory operation at the required pressure, including making good all disturbed surfaces and leaving the work complete in all respects. |
| 200 | Supplying, fixing and installing gun-metal gate valve with CI wheel, 20 mm nominal bore, screwed end, approved quality, complete., complete with all necessary fittings, joints, clamps, connectors, washers, sealants and fixing accessories required for a complete installation. The work shall include all cutting, threading/jointing, supports, connections and minor accessories necessary for proper integration with the water-supply system. The completed installation shall be tested for leakage and satisfactory operation at the required pressure, including making good all disturbed surfaces and leaving the work complete in all respects. |
| 201 | Supplying, fixing and installing gun-metal gate valve with CI wheel, 25 mm nominal bore, screwed end, approved quality, complete., complete with all necessary fittings, joints, clamps, connectors, washers, sealants and fixing accessories required for a complete installation. The work shall include all cutting, threading/jointing, supports, connections and minor accessories necessary for proper integration with the water-supply system. The completed installation shall be tested for leakage and satisfactory operation at the required pressure, including making good all disturbed surfaces and leaving the work complete in all respects. |
| 202 | Supplying, fixing and installing gun-metal gate valve with CI wheel, 32 mm nominal bore, screwed end, approved quality, complete., complete with all necessary fittings, joints, clamps, connectors, washers, sealants and fixing accessories required for a complete installation. The work shall include all cutting, threading/jointing, supports, connections and minor accessories necessary for proper integration with the water-supply system. The completed installation shall be tested for leakage and satisfactory operation at the required pressure, including making good all disturbed surfaces and leaving the work complete in all respects. |
| 203 | Supplying, fixing and installing brass ball valve with plastic float, 15 mm nominal bore, high/low pressure type, complete., complete with all necessary fittings, joints, clamps, connectors, washers, sealants and fixing accessories required for a complete installation. The work shall include all cutting, threading/jointing, supports, connections and minor accessories necessary for proper integration with the water-supply system. The completed installation shall be tested for leakage and satisfactory operation at the required pressure, including making good all disturbed surfaces and leaving the work complete in all respects. |
| 204 | Supplying, fixing and installing brass ball valve with plastic float, 20 mm nominal bore, high/low pressure type, complete., complete with all necessary fittings, joints, clamps, connectors, washers, sealants and fixing accessories required for a complete installation. The work shall include all cutting, threading/jointing, supports, connections and minor accessories necessary for proper integration with the water-supply system. The completed installation shall be tested for leakage and satisfactory operation at the required pressure, including making good all disturbed surfaces and leaving the work complete in all respects. |
| 205 | Supplying, laying, fixing and connecting glazed stoneware sewer pipe, 100 mm diameter, class SP-1, laid and jointed with 1:1 cement mortar including testing of joints, complete., complete with all necessary collars, joints, mortar, sealants, supports and connection accessories. The work shall include excavation/cutting where required, proper alignment, gradient, jointing and connection to the adjoining drainage system, including all incidental works. The completed installation shall be tested for water-tightness and free flow, with trenches/surfaces refilled or made good and the entire work completed to the satisfaction of the Engineer-in-Charge. |
| 206 | Supplying, laying, fixing and connecting glazed stoneware sewer pipe, 150 mm diameter, class SP-1, laid and jointed with 1:1 cement mortar including testing of joints, complete., complete with all necessary collars, joints, mortar, sealants, supports and connection accessories. The work shall include excavation/cutting where required, proper alignment, gradient, jointing and connection to the adjoining drainage system, including all incidental works. The completed installation shall be tested for water-tightness and free flow, with trenches/surfaces refilled or made good and the entire work completed to the satisfaction of the Engineer-in-Charge. |
| 207 | Supplying, laying, fixing and connecting non-pressure NP2 class light-duty RCC pipe, 100 mm diameter, with collars and cement-mortar joints, including testing, complete., complete with all necessary collars, joints, mortar, sealants, supports and connection accessories. The work shall include excavation/cutting where required, proper alignment, gradient, jointing and connection to the adjoining drainage system, including all incidental works. The completed installation shall be tested for water-tightness and free flow, with trenches/surfaces refilled or made good and the entire work completed to the satisfaction of the Engineer-in-Charge. |
| 208 | Supplying, laying, fixing and connecting non-pressure NP2 class light-duty RCC pipe, 150 mm diameter, with collars and cement-mortar joints, including testing, complete., complete with all necessary collars, joints, mortar, sealants, supports and connection accessories. The work shall include excavation/cutting where required, proper alignment, gradient, jointing and connection to the adjoining drainage system, including all incidental works. The completed installation shall be tested for water-tightness and free flow, with trenches/surfaces refilled or made good and the entire work completed to the satisfaction of the Engineer-in-Charge. |
| 209 | Group A light/fan/exhaust-fan/call-bell point with 1.5 sq.mm FRLS/HFFR PVC insulated copper conductor single-core cable in surface/recessed medium-class PVC conduit, with modular switch, modular plate, suitable GI box and 1.5 sq.mm earth conductor. |
| 210 | Twin-control light point with 1.5 sq.mm FRLS/HFFR PVC insulated copper conductor single-core cable in surface/recessed medium-class PVC conduit, complete with two-way modular/piano switches, box, plate and earth conductor. |
| 211 | Light/power plug wiring with 2 x 4 sq.mm FRLS/HFFR PVC insulated copper single-core conductors in surface/recessed medium-class PVC conduit, along with 1 x 4 sq.mm copper earth conductor. |
| 212 | Circuit/sub-main wiring comprising 2 x 1.5 sq.mm FRLS/HFFR PVC insulated copper single-core conductors plus 1 x 1.5 sq.mm earth conductor in surface/recessed medium-class PVC conduit. |
| 213 | Three-phase circuit/sub-main wiring comprising 4 x 2.5 sq.mm FRLS/HFFR PVC insulated copper single-core conductors plus 2 x 2.5 sq.mm earth conductors in surface/recessed medium-class PVC conduit. |
| 214 | Supplying, fixing and installing 20 mm steel conduit in surface/recessed installation, complete with all approved accessories, couplers, bends, inspection fittings and supports. Surface conduits shall be painted and recessed conduits shall include cutting/chasing and making good. The completed system shall be checked for alignment, continuity and clear passage before wiring. |
| 215 | Supplying, fixing and installing 25 mm steel conduit in surface/recessed installation, complete with all approved accessories, couplers, bends, inspection fittings and supports. Surface conduits shall be painted and recessed conduits shall include cutting/chasing and making good. The completed system shall be checked for alignment, continuity and clear passage before wiring. |
| 216 | Supplying, fixing and installing 32 mm steel conduit in surface/recessed installation, complete with all approved accessories, couplers, bends, inspection fittings and supports. Surface conduits shall be painted and recessed conduits shall include cutting/chasing and making good. The completed system shall be checked for alignment, continuity and clear passage before wiring. |
| 217 | Supplying, fixing and installing 40 mm steel conduit in surface/recessed installation, complete with all approved accessories, couplers, bends, inspection fittings and supports. Surface conduits shall be painted and recessed conduits shall include cutting/chasing and making good. The completed system shall be checked for alignment, continuity and clear passage before wiring. |
| 218 | Supplying, fixing and installing 20 mm medium-class PVC conduit in surface/recessed installation, complete with bends, couplers, junctions, inspection fittings and all necessary accessories. The work shall include cutting/chasing where required, saddling/supporting and making good. The completed conduit shall be checked for alignment, continuity and clear passage before drawing wires. |
| 219 | Supplying, fixing and installing 25 mm medium-class PVC conduit in surface/recessed installation, complete with bends, couplers, junctions, inspection fittings and all necessary accessories. The work shall include cutting/chasing where required, saddling/supporting and making good. The completed conduit shall be checked for alignment, continuity and clear passage before drawing wires. |
| 220 | Supplying, fixing and installing 32 mm medium-class PVC conduit in surface/recessed installation, complete with bends, couplers, junctions, inspection fittings and all necessary accessories. The work shall include cutting/chasing where required, saddling/supporting and making good. The completed conduit shall be checked for alignment, continuity and clear passage before drawing wires. |
| 221 | Supplying, fixing and installing 40 mm medium-class PVC conduit in surface/recessed installation, complete with bends, couplers, junctions, inspection fittings and all necessary accessories. The work shall include cutting/chasing where required, saddling/supporting and making good. The completed conduit shall be checked for alignment, continuity and clear passage before drawing wires. |
| 222 | Supplying, fixing and installing 75 x 75 x 60 mm nominal metal electrical box with suitable phenolic laminated cover, complete with screws, supports and accessories. The box shall be accurately aligned and securely fixed for switches/junctions. Metallic boxes shall be bonded to earth where required and all disturbed surfaces shall be made good. |
| 223 | Supplying, fixing and installing 100 x 100 x 60 mm nominal metal electrical box with suitable phenolic laminated cover, complete with screws, supports and accessories. The box shall be accurately aligned and securely fixed for switches/junctions. Metallic boxes shall be bonded to earth where required and all disturbed surfaces shall be made good. |
| 224 | Supplying, fixing and connecting 5/6 A modular switch on existing modular plate and switch box, complete with terminals and required accessories. The work shall include secure fixing, interconnections and all minor consumables required for a complete installation. The switch shall be tested for mechanical operation, continuity and correct polarity. |
| 225 | Supplying, fixing and connecting 15/16 A modular switch on existing modular plate and switch box, complete with terminals and required accessories. The work shall include secure fixing, interconnections and all minor consumables required for a complete installation. The switch shall be tested for mechanical operation, continuity and correct polarity. |
| 226 | Supplying, fixing and connecting 3-pin 5/6 A modular socket outlet on existing modular plate and switch box, complete with terminals and accessories. The work shall include protective earthing, connections and fixing hardware. The socket shall be tested for polarity, earth continuity, insulation resistance and satisfactory operation. |
| 227 | Supplying, fixing and connecting 6-pin 15/16 A modular socket outlet on existing modular plate and switch box, complete with terminals and accessories. The work shall include protective earthing, connections and fixing hardware. The socket shall be tested for polarity, earth continuity, insulation resistance and satisfactory operation. |
| 228 | Supplying, fixing and connecting suitable-size GI box with modular plate and cover, including 6-pin 5/6 & 15/16 A modular socket outlet and 15/16 A modular switch. The item shall include internal connections, earthing, fixing hardware and all accessories required for complete installation. The assembly shall be tested for polarity, earth continuity, insulation resistance and satisfactory operation. |
| 229 | Supplying, fixing and connecting 3-pin 5 A ceiling rose on existing junction box/wooden block, complete with terminals and accessories. The item shall include all fixing hardware and electrical connections required for complete installation. The ceiling rose shall be checked for secure fixing, continuity and correct polarity. |
| 230 | Supplying, fixing and connecting brass batten/angle holder, complete with terminals and required accessories. The item shall include secure fixing, electrical connections and all minor consumables necessary for complete installation. The holder shall be tested for continuity, polarity and secure mechanical operation. |
| 231 | Supplying, fixing and connecting suitable-size GI box with modular plate and cover, including 2 Nos. 3-pin 5/6 A modular socket outlets and 2 Nos. 5/6 A modular switches for light plugs in non-residential buildings. The item shall include internal wiring, earthing, terminals and all fixing accessories. The complete assembly shall be tested for polarity, earth continuity, insulation resistance and satisfactory operation. |
| 232 | Supplying, installing and commissioning GI pipe earthing using 40 mm dia, 4.5 m long GI earth pipe, complete with accessories, masonry enclosure, lockable cover, watering pipe, charcoal/coke and salt. The item shall include excavation, electrode connection, watering arrangement and backfilling. Earth resistance shall be measured and recorded and the completed earth pit shall be left accessible for maintenance. |
| 233 | Supplying and laying 25 x 5 mm copper strip at approximately 0.50 m below ground as strip earth electrode, including connection/termination with nuts, bolts, spring washers and required overlapping joints. The work shall include proper routing, jointing, supports and connection to the earth electrode/equipment. The completed earth path shall be tested for continuity and earth resistance and all disturbed surfaces made good. |
| 234 | Supplying, installing, testing and commissioning 12–15 W LED recessed/surface SMD downlighter, complete with aluminium body, PMMA/prismatic diffuser, high-efficiency driver, surge and short/open-circuit protection, PF ≥0.95 and associated external connections. The item shall include 1.5 sq.mm FRLS/HFFR copper connection, earthing, mounting hardware and all accessories. The fitting shall be tested for illumination, electrical safety and satisfactory operation. |
| 235 | Supplying, installing, testing and commissioning 18 W LED recessed/surface SMD downlighter, complete with aluminium body, PMMA/prismatic diffuser, high-efficiency driver, surge and short/open-circuit protection, PF ≥0.95 and associated external connections. The item shall include 1.5 sq.mm FRLS/HFFR copper connection, earthing, mounting hardware and all accessories. The fitting shall be tested for illumination, electrical safety and satisfactory operation. |
| 236 | Supplying, installing, testing and commissioning 40 W LED surface-mounted batten light with replaceable driver, suitable aluminium/CRCA body, high-efficiency LED system and complete external connections. The item shall include 1.5 sq.mm FRLS/HFFR copper connection, earthing, mounting clips and all accessories required for complete installation. The fitting shall be tested for illumination, electrical safety and satisfactory operation. |
| 237 | Providing and laying integral cement based water proofing treatment including preparation of surface as required for treatment of roofs, balconies, terraces etc consisting of following operations:(a) Applying a slurry coat of neat cement using 2.75 kg/sqm of cement admixed with water proofing compound conforming to IS. 2645 and approved by Engineer-in-charge over the RCC slab including adjoining walls upto 300 mm height including cleaning the surface before treatment.(b) Laying brick bats with mortar using broken bricks/brick bats 25 mm to 115 mm size with 50% of cement mortar 1:5 (1 cement : 5 coarse sand) admixed with water proofing compound conforming to IS : 2645 and approved by Engineer-in-charge over 20 mm thick layer of cement mortar of mix 1:5 (1 cement :5 coarse sand ) admixed with water proofing compound conforming to IS : 2645 and approved by Engineer-in-charge to required slope and treating similarly the adjoining walls upto 300 mm height including rounding of junctions of walls and slabs.(c) After two days of proper curing applying a second coat of cement slurry using 2.75 kg/ sqm of cement admixed with water proofing compound conforming to IS : 2645 and approved by Engineer-in-charge.(d) Finishing the surface with 20 mm thick jointless cement mortar of mix 1:4 (1 cement :4 coarse sand) admixed with water proofing compound conforming to IS : 2645 and approved by Engineer-in-charge including laying glass fibre cloth of approved quality in top layer of plaster and finally finishing the surface with trowel with neat cement slurry and making pattern of 300x300 mm square 3 mm deep.(e) The whole terrace so finished shall be flooded with water for a minimum period of two weeks for curing and for final test.“All above operations to be done in order and as directed and specified by the Engineer-in-Charge :With average thickness of 120 mm and minimum thickness at khurra as 65 mm. |
| 238 | Providing and laying water proofing treatment in sunken portion of WCs, bathroom etc., by applying cement slurry mixed with water proofing cement compound consisting of applying :(a) First layer of slurry of cement @ 0.488 kg/sqm mixed with water proofing cement compound @ 0.253 kg/ sqm. This layer will be allowed to air cure for 4 hours.(b) Second layer of slurry of cement @ 0.242 kg/sqm mixed with water proofing cement compound @ 0.126 kg/sqm. This layer will be allowed to air cure for 4 hours followed with water curing for 48 hours.The rate includes preparation of surface, treatment and sealing of all joints, corners, junctions of pipes and masonry with polymer mixed slurry. |
| 239 | PROVIDING AND APPLYING WATER PROOFING: Providing and applying approved waterproofing treatment to RCC tunnel walls, comprising thorough surface preparation, treatment of cracks, honeycombs and construction joints, localised sealing of seepage/leakage points as required, and application of approved multi-coat polymer-modified cementitious/crystalline waterproofing coating, complete in all respects as per manufacturer’s specifications and directions of the Engineer-in-Charge. |
| 240 | PROVIDING AND APPLYING WATER PROOFING: Providing and Apply Waterproofing: carrying out water proofing works wherever required as Per the Waterproofing Standards. Integral Cement Waterproofing Compound Confirming to IS 2645 and of approved make and manufacture enlisted by the site in-charge from time to time shall be used. The contractor shall bring the materials to the site in their original packing. The containers will be opened and the material mixed with dry cement in the proportion by weight,recommended by the manufacturers or as specifically described in the description of the item. care shall be taken in mixing, to see that the water proofing material gets well and integrally mixed with the cement and does not run out separately when water is added. Rate to include Additional 50mm PCC layer in 1:1.5:3 mix which is to be done to maintain the slop. |
| 241 | Providing and laying APP (Atactic Polypropylene Polymer) modified prefabricated five layer, 3 mm thick waterproofing membrane, black finished, reinforced with glass fibre matt, consisting of a coat of bitumen primer for bitumen membrane @ 0.40 litre/sqm, manufactured by the same membrane manufacturer, having density at 25°C of 0.87–0.89 kg/litre and viscosity 70–160 cps. Over the primer coat, the membrane shall be laid using butane torch, sealing all joints/laps and preparing the surface complete. The membrane shall have the specified physical and chemical properties, including joint strength, tear strength, softening point and cold flexibility. |
| 242 | Providing and injecting approved low-viscosity epoxy injection grout of approved make into cracks, voids and honeycombed portions of reinforced cement concrete/masonry by suitable mechanical injection gun/pump at the pressure required to ensure complete penetration and filling of the cracks/voids, including cleaning and preparation of the affected surface, drilling of injection holes at suitable spacing, fixing of injection nipples/packers, sealing of cracks between nipples with approved epoxy sealing compound, injection of epoxy grout under controlled pressure, monitoring of grout flow and pressure, cutting/removal of nipples/packers after completion and curing, sealing and making good the injection holes and treated surface, including all materials, labour, tools, tackles, plant and equipment, complete in all respects as directed by the Engineer-in-Charge. Payment shall be made on the basis of the actual weight of approved grout injected. |
| 243 | Providing and laying lightweight sunken slab filling using approved brick bats/brick ballast and cement mortar or other approved filling material to required levels, including slope formation and compaction. The work shall include filling around sanitary pipes without damaging waterproofing or pipe joints. Finished filling shall provide stable support and proper levels for subsequent floor construction. |
| 244 | Providing and fixing factory-made steel door shutter of approved gauge and profile, including steel frame, hinges, holdfasts/anchor fasteners, tower bolts, lock, handles and necessary hardware. The shutter and frame shall be accurately fabricated, aligned, plumbed and securely fixed to masonry/RCC openings. The complete door shall be tested for smooth operation, proper closing, locking and uniform clearances.Providing and fixing 1 mm thick M.S. sheet door with frame of 40x40x6 mm angle iron and 3 mm M.S. gusset plates at the junctions and corners, all necessary fittings complete, including applying a priming coat of approved steel primer.Using M.S. angels 40x40x6 mm for diagonal braces |
| 245 | Providing and fixing factory-made steel door shutter of approved gauge and profile, including steel frame, hinges, holdfasts/anchor fasteners, tower bolts, lock, handles and necessary hardware. The shutter and frame shall be accurately fabricated, aligned, plumbed and securely fixed to masonry/RCC openings. The complete door shall be tested for smooth operation, proper closing, locking and uniform clearances.Providing and fixing 1 mm thick M.S. sheet door with frame of 40x40x6 mm angle iron and 3 mm M.S. gusset plates at the junctions and corners, all necessary fittings complete, including applying a priming coat of approved steel primer.Using flats 30x6 mm for diagonal braces and central cross piece |
| 246 | Providing and fixing pressed steel door frames conforming to IS: 4351, manufactured from commercial mild steel sheet of 1.60 mm thickness, including hinges, jamb, lock jamb, bead and if required angle threshold of mild steel angle of section 50x25 mm, or base ties of 1.60 mm, pressedmild steel welded or rigidly fixed together by mechanical means, including M.S. pressed butt hinges 2.5 mm thick with mortar guards, lock strikeplate and shock absorbers as specified and applying a coat of approved steel primer after pre-treatment of the surface as directed by Engineer-in-charge: Fixing with adjustable lugs with split end tail to each jamb |
| 247 | Providing and fixing pressed steel door frames conforming to IS: 4351, manufactured from commercial mild steel sheet of 1.60 mm thickness, including hinges, jamb, lock jamb, bead and if required angle threshold of mild steel angle of section 50x25 mm, or base ties of 1.60 mm, pressedmild steel welded or rigidly fixed together by mechanical means, including M.S. pressed butt hinges 2.5 mm thick with mortar guards, lock strikeplate and shock absorbers as specified and applying a coat of approved steel primer after pre-treatment of the surface as directed by Engineer-in-charge: Fixing with carbon steel galvanised dash fastener of required dia and size |
| 248 | Providing and applying solvent-free, high-build polyurethane (PU) floor coating below and around electrical panels, of approved make, over properly prepared concrete surface, including mechanical cleaning/grinding, removal of loose particles and dust, surface preparation, application of compatible primer and minimum two coats of PU coating to achieve a minimum dry film thickness of 1.0 mm, including all materials, labour, tools and tackles, complete as per manufacturer's specifications and direction of Engineer-in-Charge. |
| 249 | Site GradingCarrying out grading of existing site surface in areas specified by the Engineer-in-Charge/HPCL, including near facilities, beside roads and other designated locations, by carrying out necessary cutting, filling, leveling and dressing of the existing ground to achieve the required finished levels and slopes. The work shall include deployment of required manpower, tools, tackles and machinery; excavation/cutting of existing earth, shifting and carting of available earth to low-lying areas, spreading and dressing of existing/imported earth, watering and compaction as required, and all incidental works necessary to achieve a smooth, uniform and properly compacted finished surface, free from undulations, depressions and unevenness, complete as directed by HPCL/Engineer-in-Charge.The maximum depth of cutting/filling under this item shall generally be up to 300 mm. Filling and leveling exceeding 400 mm depth/height shall be measured and paid separately under the applicable item. Supply of earth is excluded from the scope; wherever additional earth is required for leveling, the same shall be measured and paid separately under the applicable item.The rate shall include all manpower, machinery, equipment, handling, shifting, leveling, dressing, watering, compaction and associated operations necessary for complete execution of the work. |
| 250 | FALSE FLOORING:The false flooring system shall comprise galvanized mild-steel pedestal base plates, threaded pedestal studs, adjustable pressure die-cast aluminium top heads, and galvanized steel channel stringers forming a 610 mm × 610 mm support grid to achieve a finished floor level of 700 mm above the existing floor. The 35 mm thick, 610 mm × 610 mm teakwood particle-board panels shall be finished with aluminium foil underside, 2 mm antistatic PVC tiles/high-pressure laminate on top, and hard PVC edge lipping, with aluminium cleats for lateral stability. Panels shall be properly leveled, aligned, individually removable, and provided with necessary cutouts, ramps, slopes, steps and additional pedestals around equipment cutouts as required. The cavity shall be cleaned, dust-free and coated with polyurethane, and the complete system shall be designed to withstand a distributed load of 1250 kg/m². All detailed specifications, materials, dimensions, installation requirements, and associated provisions are as specified and detailed within this tender document itself. |
| 251 | SUPPLY & FIXING OF MS/CARBON STEEL FOUNDATION BOLTS & NUTS:Providing, supplying, fabricating and fixing MS/Carbon Steel round foundation/holding-down bolts of specified diameter and length, conforming to IS 2062 or equivalent approved grade, complete with nuts, washers, washer plates, threading, cutting, bending/hooking, welding, templates, positioning, alignment and fixing in RCC foundations/pedestals, including all materials, fabrication, labour, tools & tackles, transportation, testing/certification and all incidental works, complete as per approved drawings, specifications and directions of Engineer-in-Charge. Cost of concrete casting works shall be paid separately. |
| 252 | SUPPLY & FIXING OF HOT-DIP GALVANISED FOUNDATION BOLTS & NUTS :Supplying and fixing of BOLTS & NUTS as per IS: 2062 / SAE 1018 with minimum yield strength of 250 MPA in concrete at all levels and positions, bolts with nuts and washers, pipe sleeves etc. including surface cleaning & galvanizing with zinc coating of 610 GSM or 85 micron minimum conforming to IS: 4759, providing grease to exposed area of bolts, welding wherever necessary, protecting the same till final erection complete as per drawing, specifications and instruction of Engineer-in-Charge. Cost of concrete casting works shall be paid separately. |
| 253 | FIXING OF FOUNDATION BOLTS:Fixing, alignment and positioning of foundation bolts of approved size and grade at all levels and positions, including nuts, washers, pipe sleeves, templates/supports, necessary temporary arrangements for maintaining correct line, level, spacing and projection, providing grease to exposed portions of bolts, welding wherever necessary and protecting the same till final erection is completed, complete as per approved drawings, specifications and instructions of Engineer-in-Charge.Cost of concrete casting works shall be paid separately. |
| 254 | Earthwork excavation for foundations, pits, plinth beams, etc. |
| 255 | Earthwork excavation for foundations, pits, plinth beams, etc. up to 2.10 m depth below existing ground level in all types of soil excluding hard rock, including dressing and leveling of sides and bottom, dewatering/bailing out of water if encountered, providing necessary shoring and strutting, and disposal of surplus excavated earth within or outside HBL premises to an approved / unobjectionable location as directed by the Engineer-in-Charge, including spreading, watering, leveling and compaction complete in all respects.The rate shall include all labour, tools & tackles, equipment, lead, lift, royalties and incidental charges complete. |
| 256 | Earthwork excavation for foundations, pits, plinth beams, etc. below 2.10 m and up to 3.50 m depth existing ground level in all types of soil excluding hard rock, including dressing and leveling of sides and bottom, dewatering/bailing out of water if encountered, providing necessary shoring and strutting, and disposal of surplus excavated earth within or outside HBL premises to an approved/unobjectionable location as directed by the Engineer-in-Charge, including spreading, watering, leveling and compaction complete in all respects.The rate shall include all labour, tools & tackles, equipment, lead, lift, royalties and incidental charges complete. |
| 257 | Excavating trenches by mechinical / manual means of required width for pipes, cables, etc upto 80 mm dia including excavation for sockets, and dressing of sides, ramming of bottoms, for all depth, including getting out the excavated soil, and then returning the soil as required, in layers not exceeding 20 cm in depth, including consolidating each deposited layer by ramming, watering, etc. and disposing of surplus excavated soil as directed, within a lead of 50 m. |
| 258 | Excavating trenches by mechinical / manual means of required width for pipes, cables, etc more than 80 mm dia up to 300 mm dia including excavation for sockets, and dressing of sides, ramming of bottoms, for all depth, including getting out the excavated soil, and then returning the soil as required, in layers not exceeding 20 cm in depth, including consolidating each deposited layer by ramming, watering, etc. and disposing of surplus excavated soil as directed, within a lead of 50 m. |
| 259 | Excavating trenches by mechinical / manual means of required width for pipes, cables, etc more than 300 mm dia up to 600 mm including excavation for sockets, and dressing of sides, ramming of bottoms, for all depth, including getting out the excavated soil, and then returning the soil as required, in layers not exceeding 20 cm in depth, including consolidating each deposited layer by ramming, watering, etc. and disposing of surplus excavated soil as directed, within a lead of 50 m. |
| 260 | Backfilling around foundations, trenches, plinth beams, pits, etc. with approved excavated earth in layers not exceeding 200 mm compacted thickness, including breaking clods, watering, ramming and compacting to required density complete as directed by the Engineer-in-Charge.The rate shall include all labour, tools & tackles, equipment and incidental charges complete.Measurement for payment shall be based on compacted volume. |
| 261 | Supply and filling of approved local river sand in plinth, foundations, under footings, around foundations, trenches, etc. in layers not exceeding 200 mm compacted thickness, including conveying, spreading, watering, ramming, compacting, consolidating and dressing to required levels, grades and densities complete as per specifications and as directed by the Engineer-in-Charge.The rate shall include cost of sand, loading, unloading, transportation, royalty, all leads and lifts, labour, tools & tackles, equipment and all incidental charges complete.Measurement for payment shall be based on compacted volume. |
| 262 | Providing and laying damp-proof course (DPC) 40 mm thick in cement concrete of proportion 1:2:4 (1 cement : 2 coarse sand, Zone-III, derived from natural sources : 4 graded stone aggregate of 12.5 mm nominal size, derived from natural sources), including preparation and cleaning of the surface, laying, compacting and finishing the concrete to the required line, level, slope and thickness, with necessary curing, all complete as per drawings, specifications and directions of the Engineer-in-Charge.Rate shall include all materials, labour, tools, plant, equipment, transportation, loading/unloading, mixing, laying, compaction, finishing, curing and all incidental works necessary for satisfactory completion of the DPC. |
| 263 | Providing and laying Plain Cement Concrete (PCC) in leveling course of nominal mix 1:4:8 (1 Cement : 4 Coarse Sand : 8 Graded Stone Aggregate) using 40 mm and down graded stone aggregates, including batching, mixing, conveying, laying, compacting with mechanical vibrators, finishing to required line, level and slope, curing, and all necessary formwork/shuttering complete as per specifications and as directed by the Engineer-in-Charge.The rate shall include cost of all materials, labour, machinery, tools & tackles, water, curing, formwork, all leads and lifts and incidental charges complete.Measurement for payment shall be based on finished concrete volume. |
| 264 | Providing and laying Plain Cement Concrete (PCC) in leveling course of nominal mix 1:3:6 (1 Cement : 3 Coarse Sand : 6 Graded Stone Aggregate) using 20 mm and down graded stone aggregates, including batching, mixing, conveying, laying, compacting with mechanical vibrators, finishing to required line, level and slope, curing, and all necessary formwork/shuttering complete as per specifications and as directed by the Engineer-in-Charge.The rate shall include cost of all materials, labour, machinery, tools & tackles, water, curing, formwork, all leads and lifts and incidental charges complete.Measurement for payment shall be based on finished concrete volume. |
| 265 | Providing and laying Plain Cement Concrete (PCC) in leveling course of nominal mix 1:2:4 (1 Cement : 2 Coarse Sand : 4 Graded Stone Aggregate) using 20 mm and down graded stone aggregates, including batching, mixing, conveying, laying, compacting with mechanical vibrators, finishing to required line, level and slope, curing, and all necessary formwork/shuttering complete as per specifications and as directed by the Engineer-in-Charge.The rate shall include cost of all materials, labour, machinery, tools & tackles, water, curing, formwork, all leads and lifts and incidental charges complete.Measurement for payment shall be based on finished concrete volume. |
| 266 | Providing and laying Reinforced Cement Concrete (RCC) works up to Plinth Level of M25 grade Design Mix with minimum cement content of 360 kg/cum, using 20 mm and down graded machine crushed stone aggregates, in footings, pile caps, rafts, pedestals, columns, walls, plinth beams, curbs, equipment foundations, trenches, drains, Slab (excluading grade slab) and other RCC works, including batching, machine mixing, conveying, placing, vibrating with mechanical vibrators, tamping, compacting, finishing, curing and rendering of concrete surfaces wherever required, complete as per specifications and as directed by the Engineer-in-Charge.The design mix shall be got approved from the Consultant/Engineer-in-Charge based on necessary laboratory testing of materials and trial mixes before commencement of concreting work.The rate shall include cost of all materials excluding reinforcement steel, labour, machinery, tools & tackles, admixtures if required, all leads and lifts, and providing, erecting and dismantling of necessary centering, shuttering/formwork using steel/plywood shuttering with staging, scaffolding, bracing, supports, chamfers, fillets, surface preparation, hacking of concrete surfaces to receive plaster/finishes and all incidental works complete.Reinforcement steel shall be measured and paid separately under relevant item.Measurement for payment shall be based on finished concrete volume. |
| 267 | Providing and laying Reinforced Cement Concrete (RCC) work above Plinth level up to 10 m level of M25 grade Design Mix with minimum cement content of 360 kg/cum, using 20 mm and down graded machine crushed stone aggregates, in footings, pile caps, rafts, pedestals, columns, walls, plinth beams, curbs, equipment foundations, trenches, drains, Slab (excluading grade slab) and other RCC works, including batching, machine mixing, conveying, placing, vibrating with mechanical vibrators, tamping, compacting, finishing, curing and rendering of concrete surfaces wherever required, complete as per specifications and as directed by the Engineer-in-Charge.The design mix shall be got approved from the Consultant/Engineer-in-Charge based on necessary laboratory testing of materials and trial mixes before commencement of concreting work.The rate shall include cost of all materials excluding reinforcement steel, labour, machinery, tools & tackles, admixtures if required, all leads and lifts, and providing, erecting and dismantling of necessary centering, shuttering/formwork using steel/plywood shuttering with staging, scaffolding, bracing, supports, chamfers, fillets, surface preparation, hacking of concrete surfaces to receive plaster/finishes and all incidental works complete.Reinforcement steel shall be measured and paid separately under relevant item.Measurement for payment shall be based on finished concrete volume. |
| 268 | Providing and laying Reinforced Cement Concrete (RCC) work above 10.00 m level of M25 grade Design Mix with minimum cement content of 360 kg/cum, using 20 mm and down graded machine crushed stone aggregates, in footings, pile caps, rafts, pedestals, columns, walls, plinth beams, curbs, equipment foundations, trenches, drains, Slab (excluading grade slab) and other RCC works, including batching, machine mixing, conveying, placing, vibrating with mechanical vibrators, tamping, compacting, finishing, curing and rendering of concrete surfaces wherever required, complete as per specifications and as directed by the Engineer-in-Charge.The design mix shall be got approved from the Consultant/Engineer-in-Charge based on necessary laboratory testing of materials and trial mixes before commencement of concreting work.The rate shall include cost of all materials excluding reinforcement steel, labour, machinery, tools & tackles, admixtures if required, all leads and lifts, and providing, erecting and dismantling of necessary centering, shuttering/formwork using steel/plywood shuttering with staging, scaffolding, bracing, supports, chamfers, fillets, surface preparation, hacking of concrete surfaces to receive plaster/finishes and all incidental works complete.Reinforcement steel shall be measured and paid separately under relevant item.Measurement for payment shall be based on finished concrete volume. |
| 269 | Providing and laying Reinforced Cement Concrete (RCC) of M25 grade Design Mix with minimum cement content of 360 kg/cum, using 20 mm and down graded machine crushed stone aggregates, in grade slab/ flooring/ walkway at FFL level including batching, machine mixing, conveying, placing, vibrating with mechanical vibrators, tamping, compacting, finishing, curing and rendering of concrete surfaces wherever required, complete as per specifications and as directed by the Engineer-in-Charge.The design mix shall be got approved from the Consultant/Engineer-in-Charge based on necessary laboratory testing of materials and trial mixes before commencement of concreting work.The rate shall include cost of all materials excluding reinforcement steel, labour, machinery, tools & tackles, admixtures if required, all leads and lifts, and providing, erecting and dismantling of necessary centering, shuttering/formwork using steel/plywood shuttering with staging, scaffolding, bracing, supports, chamfers, fillets, surface preparation, hacking of concrete surfaces to receive plaster/finishes and all incidental works complete.Reinforcement steel shall be measured and paid separately under relevant item.Measurement for payment shall be based on finished concrete volume. |
| 270 | Providing, laying, spreading and compacting Granular Sub Base (GSB) over prepared sub-grade using graded stone aggregates conforming to Grading Zone V or VI of Table 400-1 of latest MORTH Specifications, with aggregate size 75 mm and down graded, complete as directed by the Engineer-in-Charge.The work shall include preparation of sub-grade, supply and transportation of approved materials to site for all leads and lifts, spreading in uniform layers of 125 mm to 150 mm compacted thickness, watering, mixing, grading and compacting with suitable vibratory/power rollers of minimum 10 tonne capacity including dry rolling and wet rolling to achieve specified compaction and density as per MORTH specifications.The item shall also include dressing to required line, grade, camber and levels, making up depressions/settlements by adding approved material, re-rolling wherever required and all operations necessary for proper completion of Granular Sub Base work complete in all respects.The rate shall include cost of all materials, loading, unloading, transportation, labour, machinery, rollers, water, tools & tackles, quality control tests, all leads and lifts and incidental charges complete.Measurement for payment shall be based on finished compacted volume. |
| 271 | Construction of Wet Mix Macadam (WMM) by providing, laying, spreading and compacting graded crushed stone aggregates using 53 mm and down graded aggregates conforming to MORTH Specifications, mixed with 2% Ordinary Portland Cement by weight of aggregate, complete as directed by the Engineer-in-Charge.The work shall include proportioning and mixing of aggregates with water at Optimum Moisture Content (OMC) in approved mechanical wet mix plant, transportation of mixed material to site in tippers, conveying to mechanical paver, laying over previously prepared surface to required thickness, line, grade, camber and alignment, compacting with 8–10 tonne vibratory roller/power roller to achieve minimum 95% of maximum dry density as per specifications including dry rolling and wet rolling.The item shall also include preparation of surface, edge protection of WMM layers, correction of irregularities, making up depressions/settlements with additional material and re-rolling to achieve specified finish and compaction complete in all respects.The rate shall include cost of aggregates, cement, water, loading, unloading, transportation, labour, machinery, wet mix plant operations, paver, rollers, lighting arrangements, maintenance of diversion roads if required, royalties, seigniorage charges, approvals from mining/applicable authorities, quality control tests, all leads and lifts and incidental charges complete.The work shall be executed in accordance with latest MORTH Specification Clause 406 (4th Revision) and as directed by the Engineer-in-Charge.Measurement for payment shall be based on finished compacted volume. |
| 272 | Providing and laying in position ready mixed or site batched Design Mix Cement Concrete of M30 grade for pavement/road works using coarse and fine aggregates derived from natural sources, Ordinary Portland Cement (OPC) / Portland Pozzolana Cement (PPC) / Portland Slag Cement (PSC), and approved admixtures in recommended proportions conforming to IS:9103 for improving workability, durability and setting characteristics without impairing strength, complete as per drawings, specifications and directions of the Engineer-in-Charge in panels using slotted ms channel shuttering of depth equal to the thickness of the pavement with required stiffness and fixing arrangement to keep them in position and enable to resist horizontal pressure of concrete, machine mixing, vibrating with screed board vibrator, pond curing for 14 days, vacuum dewatering, finished with power troweling concreting and surface texturing as per latest specification The concrete shall have minimum cement content of 350 kg/cum and shall be designed to achieve the specified strength and durability requirements. The work shall include batching, machine mixing, transportation, pumping/placing of concrete at site, laying, compacting with mechanical vibrators, curing, carriage for all leads and lifts and all operations necessary for completion of pavement concrete work complete in all respects. |
| 273 | The item shall also include rate for providing approved quality polythene paper (minimum 125 gsm) below the driveway, forming/cutting of grooves, expansion/construction joints in approved pattern and dimensions, cleaning of grooves/joints and filling/sealing with approved hot applied bituminous sealant/compound complete as directed by the Engineer-in-Charge.The rate shall include cost of all materials, admixtures, bituminous joint filler/sealant, labour, machinery, batching plant operations, transit mixers, pumps, groove cutting equipment, tools & tackles, water, quality control tests and incidental charges complete, but excluding cost of centering/shuttering, surface finishing/texturing.Reinforcement steel and dowel bar shall be measured and paid separately under relevant items. |
| 274 | Providing, driving and installing driven cast in-situ Reinforced Cement Concrete piles of specified diameter and length below pile cap level using hydraulic piling rigs with suitable power units, complete as per drawings, specifications and directions of the Engineer-in-Charge.The work shall include positioning and setting up piling rig, driving of casing/shell where required, supplying and placing M25 grade Design Mix concrete (As per approved Design Mix), providing and fixing pile shoe, driving and forming piles to the required depth and carrying safe working load not less than specified, withdrawing casing where applicable, maintaining alignment and verticality, cutting pile heads to required levels and all incidental works necessary for proper completion of piling works complete in all respects.The rate shall include cost of pile shoe, concrete, reinforcement up to 336 kg, labour, machinery, hydraulic piling rigs, power units, with bentonite solution, tools & tackles, all leads and lifts and incidental charges complete, Any reinforcement steel above 336 Kg shall be measured and paid separately under relevant item.)For actual drilling done pro-rata rate will be applied.(Size of Pile = Dia = 500mm, Depth= 20m) |
| 275 | Pile Breaking: Breaking / trimming of cast-in-situ reinforced concrete pile head of 500 mm diameter up to 2.0 m length from Natural Ground Level (NGL), including chipping, removal of weak / contaminated concrete, exposing reinforcement bars without damage, cutting and bending of reinforcement as per drawing, disposal of debris within site premises, and all necessary labour, tools & tackles complete as directed by Engineer-in-Charge. |
| 276 | Providing and fixing steel reinforcement for Reinforced Cement Concrete (RCC) works using ready-to-use “Cut, Bend and Tie” reinforcement bars of approved make, manufactured and processed at approved factory/workshop and transported to construction site, complete as per drawings, specifications and directions of the Engineer-in-Charge.The work shall include supply, cutting, bending, straightening, placing in position, tying with binding with 16 gauge MS annealed binding wire, providing necessary overlaps, hooks, chairs, spacers and supports for maintaining proper cover, alignment and spacing complete for all RCC works at all levels.Reinforcement steel shall consist of Thermo-Mechanically Treated (TMT) bars of grade Fe-500D or higher conforming to relevant IS specifications.The rate shall include cost of reinforcement steel, binding wire, wastage, cutting and bending charges, transportation, loading/unloading, labour, tools & tackles, all leads and lifts and incidental charges complete. |
| 277 | Providing and fixing high-yield reinforcement bars size = 12mm and minimum depth = 150mm into existing RCC/concrete by chemical anchoring, including setting out, drilling holes of required diameter and embedment depth using approved (rotary hammer/core) drilling equipment, thorough cleaning of holes by brushing and compressed air/vacuum, supplying and injecting approved chemical/epoxy anchoring adhesive, inserting and fixing reinforcement bars to the specified embedment, and ensuring proper bonding, alignment and projection, including all labour, materials, consumables, tools, equipment, wastage, cleaning and making good complete as directed by the Engineer.Reinforcement shall be measured and paid for separately. |
| 278 | Providing and fixing high-yield reinforcement bars size = 16 mm and minimum depth = 192mm into existing RCC/concrete by chemical anchoring, including setting out, drilling holes of required diameter and embedment depth using approved (rotary hammer/core) drilling equipment, thorough cleaning of holes by brushing and compressed air/vacuum, supplying and injecting approved chemical/epoxy anchoring adhesive, inserting and fixing reinforcement bars to the specified embedment, and ensuring proper bonding, alignment and projection, including all labour, materials, consumables, tools, equipment, wastage, cleaning and making good complete as directed by the Engineer.Reinforcement shall be measured and paid for separately. |
| 279 | Providing and fixing high-yield reinforcement bars size = 20 mm and minimum depth = 240mm into existing RCC/concrete by chemical anchoring, including setting out, drilling holes of required diameter and embedment depth using approved (rotary hammer/core) drilling equipment, thorough cleaning of holes by brushing and compressed air/vacuum, supplying and injecting approved chemical/epoxy anchoring adhesive, inserting and fixing reinforcement bars to the specified embedment, and ensuring proper bonding, alignment and projection, including all labour, materials, consumables, tools, equipment, wastage, cleaning and making good complete as directed by the Engineer.Reinforcement shall be measured and paid for separately. |
| 280 | Providing and fixing high-yield reinforcement bars size = 25 mm and minimum depth = 250mm into existing RCC/concrete by chemical anchoring, including setting out, drilling holes of required diameter and embedment depth using approved (rotary hammer/core) drilling equipment, thorough cleaning of holes by brushing and compressed air/vacuum, supplying and injecting approved chemical/epoxy anchoring adhesive, inserting and fixing reinforcement bars to the specified embedment, and ensuring proper bonding, alignment and projection, including all labour, materials, consumables, tools, equipment, wastage, cleaning and making good complete as directed by the Engineer.Reinforcement shall be measured and paid for separately. |
| 281 | Vertical Load Testing of piles in accordance with IS 2911 -IV including installation of loading paltform and preparation of pile head or construction of test cap and dismantling of test cap after test etc.complete as per specification . |
| 282 | Lateral load Testing of piles in accordance with IS 2911 -IV including installation of loading paltform and preparation of pile head or construction of test cap and dismantling of test cap after test etc.complete as per specification . |
| 283 | Pull Out Testing of piles in accordance with IS 2911 -IV including installation of loading paltform and preparation of pile head or construction of test cap and dismantling of test cap after test etc.complete as per specification . |
| 284 | Providing and constructing brick masonry work in substructure below plinth level using first quality burnt clay bricks of Class Designation 7.5 (75 KG / SQCM minimum) in cement mortar 1:6 (1 cement : 6 coarse sand), complete as per drawings, specifications and directions of the Engineer-in-Charge.The work shall include soaking of bricks before use, preparation of mortar, laying bricks in proper line, level and plumb with full mortar joints, providing all openings, offsets, projections, embeds and recesses as required, raking out joints to 10 mm depth for plastering/finishing, scaffolding, curing and all cutting, fitting and finishing works complete in all respects.The rate shall include cost of bricks, cement, sand, water, labour, scaffolding, tools & tackles, curing, all leads and lifts and incidental charges complete. |
| 285 | Providing and constructing brick masonry work in the superstructure from 0 (plinth) to 4.50 m level using first quality burnt clay bricks of Class Designation 7.5 (75 KG / SQCM minimum) in cement mortar 1:6 (1 cement : 6 coarse sand), complete as per drawings, specifications and directions of the Engineer-in-Charge.The work shall include soaking of bricks before use, preparation of mortar, laying bricks in proper line, level and plumb with full mortar joints, providing all openings, offsets, projections, embeds and recesses as required, raking out joints to 10 mm depth for plastering/finishing, scaffolding/staging, curing and all cutting, fitting and finishing works complete in all respects.The rate shall include cost of bricks, cement, sand, water, labour, scaffolding/staging, tools & tackles, curing, all leads and lifts up to 15 m height and incidental charges complete. |
| 286 | Providing and constructing brick masonry work in the superstructure from 4.50 m level up to 9.00 m level using first quality burnt clay bricks of Class Designation 7.5 (75 KG / SQCM minimum) in cement mortar 1:6 (1 cement : 6 coarse sand), complete as per drawings, specifications and directions of the Engineer-in-Charge.The work shall include soaking of bricks before use, preparation of mortar, laying bricks in proper line, level and plumb with full mortar joints, providing all openings, offsets, projections, embeds and recesses as required, raking out joints to 10 mm depth for plastering/finishing, scaffolding/staging, curing and all cutting, fitting and finishing works complete in all respects.The rate shall include cost of bricks, cement, sand, water, labour, scaffolding/staging, tools & tackles, curing, all leads and lifts up to 15 m height and incidental charges complete. |
| 287 | Providing and constructing brick masonry work in superstructure above 9 m level using first quality burnt clay bricks of Class Designation 7.5 (75 KG / SQCM minimum) in cement mortar 1:6 (1 cement : 6 coarse sand), complete as per drawings, specifications and directions of the Engineer-in-Charge.The work shall include soaking of bricks before use, preparation of mortar, laying bricks in proper line, level and plumb with full mortar joints, providing all openings, offsets, projections, embeds and recesses as required, raking out joints to 10 mm depth for plastering/finishing, scaffolding/staging, curing and all cutting, fitting and finishing works complete in all respects.The rate shall include cost of bricks, cement, sand, water, labour, scaffolding/staging, tools & tackles, curing, all leads and lifts up to 15 m height and incidental charges complete. |
| 288 | Providing and laying 115 mm thick half brick partition wall in cement mortar 1:4 (1 cement : 4 coarse sand) using approved quality table moulded chamber burnt clay bricks, complete at all levels as per drawings, specifications and directions of the Engineer-in-Charge.The work shall include soaking of bricks before use, preparation of mortar, laying bricks in proper line, level and plumb with full mortar joints, embedding 8 mm dia Tor steel reinforcement bars at every fourth course of brick masonry, proper anchoring to RCC/structural members, scaffolding/staging, curing and all cutting, fitting and finishing works complete in all respects.The rate shall include cost of bricks, cement, sand, reinforcement steel, binding wire, water, labour, scaffolding/staging, tools & tackles, all leads and lifts and incidental charges complete. |
| 289 | Providing and laying Flat brick soling (approx 75mm layer) below grade slab/floor using approved first class kiln burnt clay bricks conforming to IS:1077, laid flat/edge to edge over prepared and compacted sub-grade in proper line and level, including filling joints with sand, watering, ramming, consolidation, cutting of bricks wherever required, and all labour, materials, T&P, lead, lift, loading, unloading, wastages and incidental charges complete as per specifications and as directed by Engineer-in-Charge. |
| 290 | Providing and laying Edge to egde brick soling (approx 115mm layer) below grade slab/floor using approved first class kiln burnt clay bricks conforming to IS:1077, laid flat/edge to edge over prepared and compacted sub-grade in proper line and level, including filling joints with sand, watering, ramming, consolidation, cutting of bricks wherever required, and all labour, materials, T&P, lead, lift, loading, unloading, wastages and incidental charges complete as per specifications and as directed by Engineer-in-Charge. |
| 291 | Breaking and dismantling of reinforced cement concrete (RCC) work at all levels and heights by manual / mechanical means, including cutting of reinforcement, careful handling to avoid damage to adjoining structures, stacking of serviceable materials, and disposal of unserviceable debris to a designated location within the site or as directed by the Engineer-in-Charge, complete in all respects. |
| 292 | Breaking and dismantling of Plain cement concrete (PCC) work at all levels and heights by manual / mechanical means, careful handling to avoid damage to adjoining structures, stacking of serviceable materials, and disposal of unserviceable debris to a designated location within the site or as directed by the Engineer-in-Charge, complete in all respects. |
| 293 | Breaking and dismantling of brick masonry / ruble masonry work at all levels and heights by manual / mechanical means, careful handling to avoid damage to adjoining structures, stacking of serviceable materials, and disposal of unserviceable debris to a designated location within the site or as directed by the Engineer-in-Charge, complete in all respects. |
| 294 | Supplying and fixing dowel bars in RCC pavement, rigid pavement joints and other concrete areas complete as per IFC drawings, specifications and directions of the Engineer-in-Charge.The work shall include supply of dowel bars conforming to IS:432 Grade-I, cutting, straightening, machining, epoxy coating, fixing in proper alignment and position, provision of approved plastic sheathing on one end and all accessories required for proper load transfer arrangement in expansion/construction joints as per latest specifications of IRC:15 and IRC:58.For expansion joints, the item shall include providing and fixing closely fitting caps of minimum 100 mm length with closed end made of GI pipe or stiff plastic sleeve of minimum 2 mm thickness over the sheathed end of each dowel bar. Necessary expansion space equal to thickness of joint filler board shall be maintained between cap end and dowel bar end using approved compressible sponge filler. The arrangement shall be properly sealed/taped all around to prevent ingress of cement slurry.The work shall also include placing, supporting and securing dowel bars with approved alignment assemblies, spacers, chairs and supports to maintain proper line, level and spacing during concreting operations complete in all respects.The rate shall include cost of dowel bars, epoxy coating, sheathing, GI/plastic caps, compressible sponge filler, spacers, supports, fixing accessories, labour, tools & tackles, all leads and lifts and incidental charges complete.Approved make/brand of dowel bars and accessories shall be as approved by the Engineer-in-Charge. |
| 295 | Preparing and plastering internal wall surfaces at all heights with 12 mm thick cement plaster in cement mortar 1:4 (1 cement : 4 coarse sand), finished smooth with trowel and sponge, complete as per drawings, specifications and directions of the Engineer-in-Charge.The work shall include preparation of surfaces, hacking/raking out joints wherever required, cleaning, wetting, applying plaster to true line, level and plumb, smooth sponge finish, curing and all necessary scaffolding/staging complete in all respects.The item shall also include providing 6 mm x 6 mm recessed grooves at junctions of RCC and brick masonry surfaces, neatly formed and finished to avoid surface cracks and ensure proper architectural finish complete.The rate shall include cost of cement, sand, groove forming arrangements, water, labour, scaffolding/staging, tools & tackles, curing, all leads and lifts and incidental charges complete. |
| 296 | Preparing and plastering specified masonry, RCC and other surfaces at all heights with 6 mm thick cement plaster in cement mortar 1:3 (1 cement : 3 fine sand), finished smooth with trowel and sponge, complete as per drawings, specifications and directions of the Engineer-in-Charge.The work shall include preparation of surfaces, cleaning, hacking/raking out joints wherever required, wetting, applying plaster to the specified thickness and to true line, level and plumb, finishing of corners, edges, junctions, jambs and soffits, smooth sponge finish, curing and all necessary scaffolding/staging complete in all respects.The item shall also include proper preparation and treatment of junctions between RCC and brick masonry surfaces and providing 6 mm x 6 mm recessed grooves wherever shown or required, neatly formed and finished to avoid surface cracks and ensure proper architectural finish complete.The rate shall include cost of cement, fine sand, groove forming arrangements, water, labour, scaffolding/staging, tools & tackles, curing, all leads and lifts and incidental charges complete. |
| 297 | Providing and laying average 20 mm thick sand faced cement plaster in two coats on external wall surfaces at all heights in cement mortar 1:3 (1 cement : 3 coarse sand), complete as per drawings, specifications and directions of the Engineer-in-Charge.The work shall include preparation of surfaces, scaffolding/staging, providing and fixing chicken wire mesh at all junctions of brick masonry and RCC surfaces with minimum 150 mm overlap in all directions, groove cutting/forming wherever required, and providing additional thickness of plaster as necessary to achieve true line, level and plumb without any extra cost.The first coat shall consist of 12 mm thick cement plaster in CM 1:3 mixed with approved make waterproofing compound in proportion as per manufacturer’s specifications and finished rough to receive second coat.The second coat shall consist of 8 mm thick cement plaster in CM 1:3 finished with sponge rubbing to obtain uniform sand faced texture and proper architectural finish complete in all respects.The rate shall include cost of cement, sand, waterproofing compound, chicken mesh, water, labour, scaffolding/staging, curing, tools & tackles, all leads and lifts and incidental charges complete. |
| 298 | White washing with lime to give an even shade, of approved quality, over prepared plastered/masonry surfaces, complete as per drawings, specifications and directions of Engineer-in-Charge. The work shall include surface preparation, cleaning, preparation and application of lime wash in required coats to achieve uniform shade and finish, including scaffolding/staging, labour, tools & tackles, materials, wastage, leads, lifts and incidental charges complete.New Work 3 or more coats |
| 299 | Providing and applying 12 mm thick cement plaster of cement mortar 1:4 (1 cement : 4 coarse sand) on the internal surfaces of brick masonry drains, including preparation of surface, raking out joints, finishing the plastered surface smooth and even, and applying neat cement punning over the finished plastered surface, complete as directed by the Engineer-in-Charge.The rate shall include cost of cement, sand, groove forming arrangements, water, labour, tools & tackles, curing, all leads and lifts and incidental charges complete. |
| 300 | Distempering with 1st quality acrylic distemper (ready mixed) having VOC content less than 50 gram/litre, of approved manufacturer and required shade/colour, for new work, with two or more coats over and including one coat of water-thinnable cement primer having VOC content less than 50 gram/litre, complete as per drawings, specifications and directions of Engineer-in-Charge. The work shall include surface preparation, cleaning, minor repairs, application of primer and distemper coats uniformly to achieve an even and smooth shade, including scaffolding/staging, labour, tools & tackles, materials, wastage, leads, lifts and incidental charges complete. |
| 301 | Finishing walls with acrylic smooth exterior paint without silicone additives, of approved manufacturer and required shade/colour, for new work, with two or more coats applied @ 1.67 litre/10 sqm over and including one coat of exterior primer @ 0.90 litre/10 sqm, complete as per drawings, specifications and directions of Engineer-in-Charge. The work shall include surface preparation, cleaning, removal of loose particles and minor imperfections, application of primer and finish coats uniformly to achieve smooth, even and durable finish, including scaffolding/staging, labour, tools & tackles, materials, wastage, leads, lifts and incidental charges complete. |
| 302 | Finishing surfaces with epoxy paint On Steel Work: Providing and applying two or more coats of approved quality epoxy paint at all locations, of required shade and colour, over properly prepared surfaces and including suitable/compatible priming coat, complete as per manufacturer’s specifications, drawings and directions of Engineer-in-Charge. The work shall include surface preparation, cleaning, removal of dust, grease, loose particles and existing defective coating, minor repairs, application of primer and epoxy finish coats uniformly to achieve smooth, even and durable finish, including necessary scaffolding/staging, labour, tools & tackles, materials, wastage, leads, lifts and incidental charges complete. |
| 303 | Finishing surfaces with epoxy paint On Concrete Work: Providing and applying two or more coats of approved quality epoxy paint at all locations, of required shade and colour, over properly prepared surfaces and including suitable/compatible priming coat, complete as per manufacturer’s specifications, drawings and directions of Engineer-in-Charge. The work shall include surface preparation, cleaning, removal of dust, grease, loose particles and existing defective coating, minor repairs, application of primer and epoxy finish coats uniformly to achieve smooth, even and durable finish, including necessary scaffolding/staging, labour, tools & tackles, materials, wastage, leads, lifts and incidental charges complete. |
| 304 | Painting of rain water, soil, waste and vent pipes and fittings 75 mm diameter pipes:Providing and applying two or more coats of black anticorrosive bitumastic paint of approved brand and manufacture to rain water, soil, waste and vent pipes and fittings on new work, over and including one coat of ready-mixed zinc chromate yellow primer, complete as per drawings, specifications, manufacturer's recommendations and directions of Engineer-in-Charge. The work shall include surface preparation, cleaning, removal of rust, dust, grease and loose particles, application of primer and bitumastic paint uniformly to achieve a smooth, continuous and protective finish, including labour, brushes, tools & tackles, scaffolding/staging wherever required, materials, wastage, all leads, lifts and incidental charges complete.2 or more coats |
| 305 | Painting of rain water, soil, waste and vent pipes and fittings 100 mm diameter pipes:Providing and applying two or more coats of black anticorrosive bitumastic paint of approved brand and manufacture to rain water, soil, waste and vent pipes and fittings on new work, over and including one coat of ready-mixed zinc chromate yellow primer, complete as per drawings, specifications, manufacturer's recommendations and directions of Engineer-in-Charge. The work shall include surface preparation, cleaning, removal of rust, dust, grease and loose particles, application of primer and bitumastic paint uniformly to achieve a smooth, continuous and protective finish, including labour, brushes, tools & tackles, scaffolding/staging wherever required, materials, wastage, all leads, lifts and incidental charges complete.2 or more coats |
| 306 | Painting of rain water, soil, waste and vent pipes and fittings 150 mm diameter pipes:Providing and applying two or more coats of black anticorrosive bitumastic paint of approved brand and manufacture to rain water, soil, waste and vent pipes and fittings on new work, over and including one coat of ready-mixed zinc chromate yellow primer, complete as per drawings, specifications, manufacturer's recommendations and directions of Engineer-in-Charge. The work shall include surface preparation, cleaning, removal of rust, dust, grease and loose particles, application of primer and bitumastic paint uniformly to achieve a smooth, continuous and protective finish, including labour, brushes, tools & tackles, scaffolding/staging wherever required, materials, wastage, all leads, lifts and incidental charges complete.2 or more coats |
| 307 | Painting with synthetic enamel paint of approved brand and manufacture and required shade/colour to give an even shade, for new work with two or more coats, over properly prepared and primed surfaces, complete as per drawings, specifications and directions of Engineer-in-Charge. The work shall include surface preparation, cleaning, sanding/rubbing, removal of dust, rust and loose particles, minor making good, application of suitable primer and synthetic enamel finish coats uniformly to achieve smooth, even and durable finish, including scaffolding/staging wherever required, labour, materials, tools & tackles, wastage, all leads, lifts and incidental charges complete. |
| 308 | Painting with acid proof paint of approved brand and manufacture and required colour to give an even shade, for new work with two or more coats, over properly prepared surfaces, complete as per drawings, specifications and directions of Engineer-in-Charge. The work shall include surface preparation, cleaning, removal of dust, grease, loose particles and minor imperfections, application of suitable primer where specified and acid-proof finish coats uniformly to achieve a smooth, even and durable chemical-resistant finish, including scaffolding/staging wherever required, labour, materials, tools & tackles, wastage, all leads, lifts and incidental charges complete. |
| 309 | Painting with aluminium paint of approved brand and manufacture and required shade/finish to give an even shade, for new work with two or more coats, over properly prepared surfaces, complete as per drawings, specifications and directions of Engineer-in-Charge. The work shall include surface preparation, cleaning, removal of dust, rust, grease and loose particles, application of suitable primer where specified and aluminium paint coats uniformly to achieve smooth, even and durable finish, including scaffolding/staging wherever required, labour, materials, tools & tackles, wastage, all leads, lifts and incidental charges complete. |
| 310 | Providing and applying white cement based putty, of approved manufacturer, average 1 mm thickness over plastered ceiling surfaces, complete as per drawings, specifications and directions of Engineer-in-Charge. The work shall include surface preparation, cleaning, filling of minor imperfections, application of putty, sanding/rubbing to obtain smooth and even finish, including scaffolding/staging, labour, tools & tackles, materials, wastage, leads, lifts and incidental charges complete. |
| 311 | Providing and applying white cement based putty, of approved manufacturer, average 2 mm total thickness in two or more coats over plastered wall surfaces, complete as per drawings, specifications and directions of Engineer-in-Charge. The work shall include surface preparation, cleaning, filling of minor imperfections, application of successive coats, drying, sanding/rubbing and obtaining smooth and even finish, including scaffolding/staging, labour, tools & tackles, materials, wastage, leads, lifts and incidental charges complete. |
| 312 | Providing and applying two coats of acrylic emulsion paint internal: Providing and applying two coats of approved quality acrylic emulsion paint of required shade and colour over prepared plastered/puttied and primed wall surfaces, complete as per drawings, specifications and directions of Engineer-in-Charge. The work shall include preparation of surface, removal of dust and loose particles, rubbing down/sanding wherever required, application of primer wherever specified, filling and making good minor imperfections, application of two uniform coats of acrylic emulsion paint by brush/roller/spray as approved, allowing adequate drying between coats and obtaining smooth, even and uniform finish. The rate shall include cost of paint, thinning medium, labour, brushes, rollers, tools & tackles, scaffolding/staging, wastage, all leads and lifts and incidental charges complete. |
| 313 | Cement concrete flooring 40 mm thick in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate) with 20 mm nominal size stone aggregate, finished with a floating coat of neat cement, including cement slurry, complete as per drawings, specifications and directions of Engineer-in-Charge. The work shall include preparation and cleaning of base, laying, compacting, levelling and finishing to required line, level and slope, providing neat cement floating coat and curing, including all materials, labour, tools & tackles, scaffolding wherever required, leads, lifts, wastage and incidental charges complete. |
| 314 | Providing and fixing glass strips in joints of terrazzo/cement concrete flooring, including cutting and preparing joints, fixing 40 mm wide and 4 mm thick glass strips true to line, level and alignment, properly embedded and secured in cement mortar/slurry, complete as per drawings, specifications and directions of Engineer-in-Charge. The rate shall include cost of glass strips, cement mortar/slurry, labour, cutting, fixing, tools & tackles, wastage, leads, lifts and incidental charges complete. |
| 315 | Providing and laying 1st quality ceramic glazed floor tiles of size 300 × 300 mm, conforming to IS 15622, of approved make, colour and shade, laid on 20 mm thick cement mortar 1:4 (1 cement : 4 coarse sand), including cement slurry @ 3.3 kg/sqm, properly aligned, levelled and bedded. The work shall include cutting and fixing tiles to required line, level and slope, jointing and pointing with white cement and matching pigment, cleaning and finishing complete as per drawings, specifications and directions of Engineer-in-Charge. Rate shall include tiles, cement, sand, slurry, pigment, labour, tools & tackles, wastage, leads, lifts and incidental charges complete. |
| 316 | Providing and fixing 1st quality ceramic glazed tiles conforming to IS 15622, of approved make, colour and shade, of size as approved by Engineer-in-Charge, for skirting, risers of steps and dados, laid over 12 mm thick cement mortar 1:3 (1 cement : 3 coarse sand) and jointed with grey cement slurry @ 3.3 kg/sqm, including cutting, fitting, alignment, levelling and pointing of joints with white cement mixed with matching pigment, complete as per drawings, specifications and directions of Engineer-in-Charge. Rate shall include tiles, cement, sand, slurry, pigment, labour, cutting, wastage, tools & tackles, leads, lifts and incidental charges complete. |
| 317 | Providing and laying 1st quality 600 mm X 600 mm vitrified floor tiles of approved make, size and shade, thickness as specified by manufacturer, having water absorption < 0.08% and conforming to IS 15622, laid on 20 mm thick cement mortar 1:4 (1 cement : 4 coarse sand), including grey cement slurry @ 3.3 kg/sqm, properly aligned, levelled and laid to required line, level and slope. Joints shall be grouted/pointed with white cement and matching pigment, including cutting, fitting, cleaning and finishing complete as per drawings, specifications and directions of Engineer-in-Charge. Rate shall include tiles, cement, sand, slurry, grout/pigment, labour, cutting, wastage, tools & tackles, leads, lifts and incidental charges complete. |
| 318 | Providing and laying 1st quality 800 mm X 800 mm vitrified floor tiles of approved make, size and shade, thickness as specified by manufacturer, having water absorption < 0.08% and conforming to IS 15622, laid on 20 mm thick cement mortar 1:4 (1 cement : 4 coarse sand), including grey cement slurry @ 3.3 kg/sqm, properly aligned, levelled and laid to required line, level and slope. Joints shall be grouted/pointed with white cement and matching pigment, including cutting, fitting, cleaning and finishing complete as per drawings, specifications and directions of Engineer-in-Charge. Rate shall include tiles, cement, sand, slurry, grout/pigment, labour, cutting, wastage, tools & tackles, leads, lifts and incidental charges complete. |
| 319 | Providing and laying 1st quality 600 mm X 600 mm vitrified tiles of approved make, size, colour and shade, thickness as specified by the manufacturer, having water absorption less than 0.08% and conforming to IS 15622, in skirting and risers of steps, laid over 12 mm thick cement mortar 1:3 (1 cement : 3 coarse sand) and jointed with grey cement slurry @ 3.3 kg/sqm. The work shall include cutting, fitting, alignment, levelling and grouting of joints with white cement and matching pigment, complete as per drawings, specifications and directions of Engineer-in-Charge. Rate shall include tiles, cement, sand, cement slurry, white cement, matching pigment, labour, cutting, wastage, tools & tackles, leads, lifts and incidental charges complete. |
| 320 | Providing and laying 1st quality 800 mm X 800 mm vitrified tiles of approved make, size, colour and shade, thickness as specified by the manufacturer, having water absorption less than 0.08% and conforming to IS 15622, in skirting and risers of steps, laid over 12 mm thick cement mortar 1:3 (1 cement : 3 coarse sand) and jointed with grey cement slurry @ 3.3 kg/sqm. The work shall include cutting, fitting, alignment, levelling and grouting of joints with white cement and matching pigment, complete as per drawings, specifications and directions of Engineer-in-Charge. Rate shall include tiles, cement, sand, cement slurry, white cement, matching pigment, labour, cutting, wastage, tools & tackles, leads, lifts and incidental charges complete. |
| 321 | Providing and laying polished granite stone flooring of approved make, colour, shade and texture in required design and patterns, in linear as well as curvilinear portions, with 18 mm thick granite stone slabs laid over 20 mm average thick cement mortar 1:4 (1 cement : 4 coarse sand). The work shall include laying and jointing with cement slurry, pointing joints with white cement slurry mixed with matching pigment, cutting, edge dressing, alignment, rubbing, curing and polishing as required to achieve the specified finish, complete as per architectural drawings, specifications and directions of Engineer-in-Charge. Rate shall include granite slabs, cement, sand, slurry, pigment, labour, cutting, wastage, tools & tackles, curing, rubbing/polishing, leads, lifts and incidental charges complete.Polished Granite stone slab of all colour and texture. |
| 322 | Providing and fixing 18 mm thick gang saw cut (Area of slab upto 0.50 square meter), polished and machine-cut marble stone for wall lining/veneer work, of approved Raj Nagar plain white marble/Udaipur green marble/Zebra black marble, over average 12 mm thick backing grout in cement mortar 1:3 (1 cement : 3 coarse sand), including jointing and pointing with white cement mortar 1:2 (1 white cement : 2 marble dust) mixed with pigment to match marble shade. The work shall include cutting, dressing, fixing, alignment, levelling, cleaning and finishing complete as per drawings, specifications and directions of Engineer-in-Charge. Marble shall be secured to backing with cramps, cramps being measured and paid separately. Rate shall include marble, cement, sand, marble dust, pigment, grout, labour, cutting, dressing, tools & tackles, scaffolding, wastage, leads, lifts and incidental charges complete. |
| 323 | Providing and fixing 18 mm thick gang saw cut (Area of slab over 0.50 square meter), polished and machine-cut marble stone for wall lining/veneer work, of approved Raj Nagar plain white marble/Udaipur green marble/Zebra black marble, over average 12 mm thick backing grout in cement mortar 1:3 (1 cement : 3 coarse sand), including jointing and pointing with white cement mortar 1:2 (1 white cement : 2 marble dust) mixed with pigment to match marble shade. The work shall include cutting, dressing, fixing, alignment, levelling, cleaning and finishing complete as per drawings, specifications and directions of Engineer-in-Charge. Marble shall be secured to backing with cramps, cramps being measured and paid separately. Rate shall include marble, cement, sand, marble dust, pigment, grout, labour, cutting, dressing, tools & tackles, scaffolding, wastage, leads, lifts and incidental charges complete. |
| 324 | Providing edge moulding to 18 mm thick marble stone counters, Vanities etc., including machine polishing to edge to give high gloss finish etc. complete as per design approved by Engineerin- Charge. |
| 325 | Providing and laying Kota stone slabs, 20 mm thick, in treads and risers of staircase, of approved quality and shade, laid over 12 mm average thick cement mortar 1:3 (1 cement : 3 coarse sand), including jointing with grey cement slurry mixed with pigment to match the shade of stone, cutting, dressing, edge finishing, rubbing and polishing complete, including providing the stone in single length for each tread/riser wherever required, all complete as directed by Engineer-in-Charge. |
| 326 | Extra for providing pre-finished nosing to treads of steps in Kota stone/sand stone slab, including fixing and finishing complete. |
| 327 | Providing and fixing 10 mm thick acid and/or alkali resistant tiles of approved make, colour, shade, texture and size, conforming to IS 4457, on prepared concrete/cement mortar surface, laid over 10 mm thick bedding mortar in the proportion of 1:4 (1 part acid-proof cement : 4 parts coarse sand), including providing and applying acid and/or alkali resistant cement for filling and finishing the joints, cutting, shaping and fitting tiles around corners, edges, columns, floor traps and other obstructions, maintaining uniform line, level and slope, cleaning, curing and final finishing, complete in all respects as specified and directed by the Engineer-in-Charge. The tiles and jointing materials shall be resistant to the acids, alkalis, chemicals and other substances likely to come in contact with the finished surface. All materials, labour, tools, tackles, scaffolding and incidental works necessary for proper completion shall be included. |
| 328 | Providing and fixing 10 mm thick acid and/or alkali resistant tiles of approved make, colour, shade, texture and size, conforming to IS 4457, in dado/skirting over prepared surface, laid on 12 mm thick bedding mortar in the proportion of 1:4 (1 part acid-proof cement : 4 parts coarse sand), including filling and finishing joints with acid and/or alkali resistant cement, cutting, dressing, fixing, alignment, finishing and cleaning complete, including all materials, labour, tools and incidental works, as directed by the Engineer-in-Charge. |
| 329 | Providing and fixing expansion hold fasteners with threaded dia of 6 mm on C.C. /R.C.C./Brick masonry surface backing including drilling necessary holes and the cost of bolt etc complete. |
| 330 | Providing and fixing expansion hold fasteners with threaded dia of 10 mm on C.C. /R.C.C./Brick masonry surface backing including drilling necessary holes and the cost of bolt etc complete. |
| 331 | Providing and fixing expansion hold fasteners with threaded dia of 12 mm on C.C. /R.C.C./Brick masonry surface backing including drilling necessary holes and the cost of bolt etc complete. |
| 332 | Providing and fixing expandable fasteners 25 mm long size with necessary plastic sleeves and galvanised M.S. screws including drilling holes in masonry work /CC/ R.C.C. and making good etc. complete. |
| 333 | Providing and fixing expandable fasteners 32 mm long size with necessary plastic sleeves and galvanised M.S. screws including drilling holes in masonry work /CC/ R.C.C. and making good etc. complete. |
| 334 | Providing and fixing expandable fasteners 40 mm long size with necessary plastic sleeves and galvanised M.S. screws including drilling holes in masonry work /CC/ R.C.C. and making good etc. complete. |
| 335 | Providing and fixing expandable fasteners 50 mm long size with necessary plastic sleeves and galvanised M.S. screws including drilling holes in masonry work /CC/ R.C.C. and making good etc. complete. |
| 336 | Providing and fixing false ceiling at all height including providing and fixing of frame work made of special sections, power pressed from M.S. sheets and galvanized with zinc coating of 120 gms/sqm (both side inclusive) as per IS : 277 and consisting of angle cleats of size 25 mm wide x 1.6 mm thick with flanges of 27 mm and 37mm, at 1200 mm centre to centre, one flange fixed to the ceiling with dash fastener 12.5 mm dia x 50mm long with 6mm dia bolts, other flange of cleat fixed to the angle hangers of 25x10x0.50 mm of required length with nuts & bolts of required size and other end of angle hanger fixed with intermediate G.I. channels 45x15x0.9 mm running at the spacing of 1200 mm centre to centre, to which the ceiling section 0.5 mm thick bottom wedge of 80 mm with tapered flanges of 26 mm each having lips of 10.5 mm, at 450 mm centre to centre, shall be fixed in a direction perpendicular to G.I. intermediate channel with connecting clips made out of 2.64 mm dia x 230 mm long G.I. wire at every junction, including fixing perimeter channels 0.5 mm thick 27 mm high having flanges of 20 mm and 30 mm long, the perimeter of ceiling fixed to wall/partition with the help of rawl plugs at 450 mm centre, with 25mm long dry wall screws @ 230 mm interval, including fixing of gypsum board to ceiling section and perimeter channel with the help of dry wallscrews of size 3.5 x 25 mm at 230 mm c/c, including jointing and finishing to a flush finish of tapered and square edges of the board with recommended jointing compound , jointing tapes, finishing with jointing compound in 3 layers covering upto 150 mm on both sides of joint and two coats of primer suitable for board, all as per manufacturer’s specification and also including the cost of making openings for light fittings, grills, diffusers, cutouts made with frame of perimeter channels suitably fixed, all complete as per drawings, specification and direction of the Engineer in Charge but excluding the cost of painting with : 12.5 mm thick tapered edge gypsum plain board conforming to IS: 2095- (Part I) :2011 (Board with BIS certification marks) |
| 337 | Providing and fixing tiled false ceiling of GI Metal Ceiling Lay-in plain Tegular edge Global White colour tiles of size 595x595 mm, 0.5 mm thick with 8 mm drop, made of GI sheet having galvanizing of 100 gms/sqm (both sides inclusive) and electrostatically polyester powder coated of thickness 60 microns (minimum), including factory painted after bending, in true horizontal level, suspended on inter locking metal grid of hot dipped galvanized steel sections (galvanized @ 120 grams/sqm, both side inclusive) consisting of main “T” runner with suitably spaced joints to get required length and of size 24x38 mm made from 0.30 mm thick (minimum) sheet, spaced at 1200 mm center to center and cross “T” of size 24x25 mm made of 0.30 mm thick (minimum) sheet, 1200 mm long spaced between main “T” at 600 mm center to center to form a grid of 1200x600 mm and secondary cross “T” of length 600 mm and size 24x25 mm made of 0.30 mm thick (minimum) sheet to be interlocked at middle of the 1200x600 mm panel to form grids of 600x600 mm and wall angle of size 24x24x0.3 mm and laying false ceiling tiles of approved texture in the grid including required cutting/making, opening for services like diffusers, grills, light fittings, fixtures, smoke detectors etc. Main “T” runners to be suspended from ceiling using GI slotted cleats of size 27 x 37 x 25 x 1.6 mm fixed to ceiling with 12.5 mm dia and 50 mm long dash fasteners, 4 mm GI adjustable rods with galvanised butterfly level clips of size 85 x 30 x 0.8 mm spaced at 1200 mm center to center along main T, bottom exposed width of 24 mm of all T-sections shall be pre-painted with polyester paint, all complete for all heights as per specifications, drawings and as directed by Engineer-in-charge. |
| 338 | Providing and fixing tiled false ceiling of GI Metal Ceiling Lay in perforated Tegular edge global white colour tiles of size 595x595 mm and 0.5 mm thick with 8 mm drop; made of GI sheet having galvanizing of 100 gms/ sqm (both sides inclusive) and 20% perforation area with 1.8 mm dia holes and having NRC (Noise Reduction Coefficient ) of 0.5, electro statically polyester powder coated of thickness 60 microns (minimum), including factory painted after bending and perforation, and backed with a black Glass fiber acoustical fleece, in true horizontal level, suspended on inter locking metal grid of hot dipped galvanized steel sections (galvanized @ 120 grams/sqm, both side inclusive) consisting of main “T” runner with suitably spaced joints to get required length and of size 24x38 mm made from 0.30 mm thick (minimum) sheet, spaced at 1200 mm center to center and cross “T” of size 24x25 mm made of 0.30 mm thick (minimum) sheet, 1200 mm long spaced between main “T” at 600 mm center to center to form a grid of 1200x600 mm and secondary cross “T” of length 600 mm and size 24x25 mm made of 0.30 mm thick (minimum) sheet to be interlocked at middle of the 1200x600 mm panel to form grids of 600x600 mm and wall angle of size 24x24x0.3 mm and laying false ceiling tiles of approved texture in the grid including required cutting/making, opening for services like diffusers, grills, light fittings, fixtures, smoke detectors etc. Main “T” runners to be suspended from ceiling using GI slotted cleats of size 27 x 37 x 25 x 1.6 mm fixed to ceiling with 12.5 mm dia and 50 mm long dash fasteners, 4 mm GI adjustable rods with galvanised butterfly level clips of size 85 x 30 x 0.8 mm spaced at 1200 mm center to center along main T, bottom exposed width of 24 mm of all T-sections shall be pre-painted with polyester paint, all complete for all heights as per specifications, drawings and as directed by Engineer-in-charge. |
| 339 | Providing and fixing tiled false ceiling of 12.5 mm thick square edge PVC Laminated Gypsum Tile of size 595x595 mm, made of Gypsum plasterboard, manufactured from natural gypsum as per IS 2095 part I and laminated with white 0.16mm thick fire retardant PVC film on the face side and 12micron metalized polyester on the back side with all edges sealed with the face side PVC film which goes around and wraps the edges and is bonded to the edges and the back side metalized polyester film so as to make the tile a completely sealed unit, in true horizontal level, suspended on inter locking metal grid of hot dipped galvanized steel sections (galvanized @ 120 grams/sqm, both side inclusive) consisting of main “T” runner with suitably spaced joints to get required length and of size 24x38 mm made from 0.30 mm thick (minimum) sheet, spaced at 1200 mm center to center and cross “T” of size 24x25 mm made of 0.30 mm thick (minimum) sheet, 1200 mm long spaced between main “T” at 600 mm center to center to form a grid of 1200x600 mm and secondary cross “T” of length 600 mm and size 24x25 mm made of 0.30 mm thick (minimum) sheet to be interlocked at middle of the 1200x600 mm panel to form grids of 600x600 mm and wall angle of size 24x24x0.3 mm and laying false ceiling tiles of approved texture in the grid including required cutting/making, opening for services like diffusers, grills, light fittings, fixtures, smoke detectors etc. Main “T” runners to be suspended from ceiling using GI slotted cleats of size 27 x 37 x 25 x 1.6 mm fixed to ceiling with 12.5 mm dia and 50 mm long dash fasteners, 4 mm GI adjustable rods with galvanised butterfly level clips of size 85 x 30 x 0.8 mm spaced at 1200 mm center to center along main T, bottom exposed width of 24 mm of all T-sections shall be pre-painted with polyester paint, all complete for all heights as per specifications, drawings and as directed by Engineer-in-charge. |
| 340 | Providing and fixing tiled false ceiling of 12.5 mm thick fully Perforated Gypsum Board tile made from plasterboard having glass fibre conforming to IS: 2095 part I, of size 595x595 mm, having perforation of 9.7x9.7 mm at 19.4 mm c/c with center borders of 48 mm and the side borders of 30 mm, backed with non woven tissue on the back side, having an NRC (Noise Reduction Coefficient) of 0.79, with 50 mm resin bonded glass wool backing, in true horizontal level, suspended on inter locking metal grid of hot dipped galvanized steel sections (galvanized @ 120 grams/sqm, both side inclusive) consisting of main “T” runner with suitably spaced joints to get required length and of size 24x38 mm made from 0.30 mm thick (minimum) sheet, spaced at 1200 mm center to center and cross “T” of size 24x25 mm made of 0.30 mm thick (minimum) sheet, 1200 mm long spaced between main “T” at 600 mm center to center to form a grid of 1200x600 mm and secondary cross “T” of length 600 mm and size 24x25 mm made of 0.30 mm thick (minimum) sheet to be interlocked at middle of the 1200x600 mm panel to form grids of 600x600 mm and wall angle of size 24x24x0.3 mm and laying false ceiling tiles of approved texture in the grid including required cutting/making, opening for services like diffusers, grills, light fittings, fixtures, smoke detectors etc. Main “T” runners to be suspended from ceiling using GI slotted cleats of size 27 x 37 x 25 x 1.6 mm fixed to ceiling with 12.5 mm dia and 50 mm long dash fasteners, 4 mm GI adjustable rods with galvanised butterfly level clips of size 85 x 30 x 0.8 mm spaced at 1200 mm center to center along main T, bottom exposed width of 24 mm of all T-sections shall be pre-painted with polyester paint, all complete for all heights as per specifications, drawings and as directed by Engineer-in-charge. |
| 341 | Supplying, fabricating and fixing aluminium work for fixed portions of panel-room partitions using approved extruded built-up tubular/Z sections conforming to IS:733 and IS:1285, powder coated with minimum 50 micron coating. The work shall include mitring, mechanical jointing, cleat angles, aluminium snap beads, EPDM/neoprene gaskets, CP brass/SS screws, dash-fastener provisions and all necessary accessories for a rigid and accurately aligned frame. Glazing/paneling and dash fasteners shall be measured and paid separately as applicable; the completed frame shall be checked for plumb, level, alignment and secure fixing. |
| 342 | Supplying, fabricating and fixing powder-coated aluminium shutter for panel-room door, window or ventilator using approved extruded tubular/Z sections conforming to IS:733 and IS:1285, with minimum 50 micron powder coating. The item shall include hinges/pivots, EPDM/neoprene gaskets, provision for hardware, mechanical joints, cleats, screws and all necessary accessories for complete shutter fabrication and fixing. The shutter shall be aligned, adjusted and tested for smooth opening, closing and proper seating; fittings shall be paid separately where specified. |
| 343 | Supplying and fixing 12 mm thick pre-laminated particle board conforming to IS:12823 Grade I Type II, with decorative lamination on both sides, fixed within aluminium panel-room partition/door frames. The work shall include cutting to required size, edge treatment, CP brass/SS screws and all necessary fixing accessories. Panels shall be neatly aligned with uniform joints and securely fixed, with all exposed edges finished cleanly. |
| 344 | Supplying and fixing 4 mm thick float glass glazing in aluminium panel-room partitions, doors and fixed panels, complete with EPDM/neoprene gasket and all necessary glazing accessories. The glass shall be accurately cut, fitted and secured within aluminium snap-beaded frames without cracks, chips or excessive clearance. The completed glazing shall be checked for proper seating, uniform appearance and safe fixing. |
| 345 | Supplying and fixing 5 mm thick float glass glazing in aluminium panel-room partitions, doors and fixed panels, complete with EPDM/neoprene gasket and all necessary glazing accessories. The glass shall be accurately cut, fitted and secured within aluminium snap-beaded frames without cracks, chips or excessive clearance. The completed glazing shall be checked for proper seating, uniform appearance and safe fixing. |
| 346 | Supplying and fixing 8 mm thick float glass glazing in aluminium panel-room partitions, doors and fixed panels, complete with EPDM/neoprene gasket and all necessary glazing accessories. The glass shall be accurately cut, fitted and secured within aluminium snap-beaded frames without cracks, chips or excessive clearance. The completed glazing shall be checked for proper seating, uniform appearance and safe fixing. |
| 347 | Supplying, fixing and commissioning double-action hydraulic floor spring conforming to IS:6315, suitable for aluminium panel-room door shutters up to 125 kg, with brass cover plate of minimum 1.25 mm thickness. The work shall include floor cutting, embedding, brass pivot, outer box, slide plate and all fixing accessories. The door shall be adjusted and tested for smooth double-action operation, controlled closing and proper alignment, with the floor finish made good after installation. |
| 348 | Supplying and fixing 32 mm outside diameter, 3.0 mm thick and 2100 mm long anodised/ powder-coated/ polyester powder-coated aluminium tubular pull handle for panel-room door, complete with stainless-steel screws and required fixing accessories. The handle shall be securely anchored to the shutter at the approved locations with suitable backing/support. The completed handle shall be checked for rigidity, alignment, smooth edges and secure fixing. |
| 349 | Supplying and fixing brass 100 mm mortice latch and lock with six levers, without pair of handles, of approved make for aluminium panel-room doors, including necessary cutting and making good. The item shall include lock body, cylinder/key arrangement as applicable, screws, fixing accessories and adjustment. The lock shall be tested for smooth key operation, positive latching, proper engagement and secure locking of the door. |
| 350 | Supplying and fixing anodised/ powder-coated/ polyester powder-coated aluminium casement window fastener of required length for aluminium panel-room windows, complete with necessary stainless-steel/approved screws and accessories. The fastener shall be securely fixed and adjusted to provide positive locking of the window shutter. The completed assembly shall be tested for smooth operation, secure engagement and proper alignment. |
| 351 | Supplying and applying weather/structural non-sag elastomeric PU sealant over approved backer rod at the interface between aluminium partition frames and adjacent RCC, brick, stone, ceramic or gypsum surfaces, for joints up to 5 mm depth and 5 mm width, complying with ASTM C920, DIN 18540-F and ISO 11600. The work shall include cleaning and preparation of joint surfaces, primer where recommended, backer rod, sealant application and tooling to form a neat continuous seal. The completed joint shall be free from gaps, voids and discontinuities and shall be inspected for proper adhesion and weather-tightness. |
| 352 | Supplying and applying weather/structural non-sag elastomeric PU sealant over approved backer rod at the interface between aluminium partition frames and adjacent RCC, brick, stone, ceramic or gypsum surfaces, for joints above depth of 5 mm to 10 mm depth and width of 5 mm to 10 mm, complying with ASTM C920, DIN 18540-F and ISO 11600. The work shall include cleaning and preparation of joint surfaces, primer where recommended, backer rod, sealant application and tooling to form a neat continuous seal. The completed joint shall be free from gaps, voids and discontinuities and shall be inspected for proper adhesion and weather-tightness. |
| 353 | Supplying and applying weather/structural non-sag elastomeric PU sealant over approved backer rod at the interface between aluminium partition frames and adjacent RCC, brick, stone, ceramic or gypsum surfaces, for joints above depth of 10 mm to 20 mm depth and and width of 10 mm to 20 mm, complying with ASTM C920, DIN 18540-F and ISO 11600. The work shall include cleaning and preparation of joint surfaces, primer where recommended, backer rod, sealant application and tooling to form a neat continuous seal. The completed joint shall be free from gaps, voids and discontinuities and shall be inspected for proper adhesion and weather-tightness. |
| 354 | Providing and laying dry lean cement concrete sub-base over prepared sub-grade using coarse and fine aggregates conforming to IS:383, with aggregate-cement ratio not exceeding 15:1 and cement content not less than 150 kg/cum. The work shall include batching, transportation, mechanical paving, compaction with 8–10 tonne vibratory roller, finishing and curing. The completed DLC shall be checked for thickness, levels, strength and surface regularity. |
| 355 | Providing and fixing factory-made solid core flush door shutter, 35 mm thick, conforming to IS 2202 (Part-I), with face veneers of approved quality, hardwood lipping on all edges, including rebating where required, fixing with approved quality M.S./SS butt hinges with necessary screws, cutting, fitting and fixing complete in all respects as directed by Engineer-in-Charge. |
| 356 | Providing and fixing factory-made PVC door set for toilet/washroom, comprising PVC door frame/chowkhat of approved size and section and minimum 25 mm thick PVC door shutter, made from rigid, waterproof, termite-proof PVC material of approved make, colour and finish, including cutting, fitting and fixing of frame to masonry opening with suitable fasteners, filling/packing of gaps with approved material, fixing of shutter with stainless steel/MS hinges, SS/PVC lever handle, tower bolt/latch, mortice/appropriate toilet lock, door stopper and all necessary screws, fasteners, fittings and accessories, including making good the adjoining surfaces and complete installation in all respects as directed by the Engineer-in-Charge. |
| 357 | Providing and fixing complete WPC door assembly, comprising factory-made WPC solid door frame/chowkhat of approved section and 35 mm thick WPC solid plain flush door shutter, including cutting, mitring, jointing, fixing to wall/opening with suitable fasteners, SS/M.S. butt hinges, screws, necessary hardware, sealant, making good and all labour, materials, tools and tackles, complete as directed by Engineer-in-Charge. |
| 358 | Providing, supplying and fixing factory-made galvanized iron (GI) rolling shutter of approved make, manufactured from cold-rolled galvanized steel laths of minimum 80 mm width and 1.20 mm thickness, interlocked with each other throughout their length and secured at ends with end locks, complete with galvanized steel top cover, specially designed galvanized/M.S. pipe shaft, brackets, side guides/channels, bottom rail with suitable angle/flat, high tensile steel wire springs, ball bearings, locking arrangement for operation from inside and outside, pull-and-push manual operating arrangement, including cutting, fabrication, drilling, welding where required, hoisting, fixing in position, alignment, leveling, anchoring to masonry/RCC/structural steel, necessary nuts, bolts, screws, fasteners and all other accessories, applying approved protective coating/primer to non-galvanized portions, and making good the adjoining surfaces, complete in all respects as directed by the Engineer-in-Charge. |
| 359 | Providing and fixing M.S. grills of required pattern in frames of windows etc. with M.S. flats, square or round bars etc., including priming coat with approved steel primer and 2 coat paint, all complete — fixed to steel windows by welding /fixed to openings/wooden frames with rawl plugs, screws etc. |
| 360 | Providing and fixing wooden door frame/chowkhat, of approved section and size, properly seasoned and treated, wrought framed, rebated, tenoned and mortised, including providing and fixing holdfasts/dash fasteners, packing with cement mortar/concrete, cutting, fitting and fixing complete as directed by Engineer-in-Charge. |
| 361 | “Providing, supplying and fixing 6 mm thick M.S. chequered plate of approved quality for flooring/treads/landings/platforms, including cutting to required size, welding/fixing to supporting steel members, necessary edge preparation, hoisting, handling and applying one coat of approved steel primer, complete as directed by Engineer-in-Charge.” |
| 362 | Providing and applying road surface marking with ready-mixed road marking paint conforming to IS:164 on new bituminous/concrete surfaces, including cleaning, setting out, masking and application of two or more coats to obtain a uniform finish. The work shall include all labour, materials and tools necessary for sharp and clearly visible markings. Completed markings shall be checked for width, alignment, coverage and uniformity. |
| 363 | Providing and laying factory-made M-25 grade cement concrete kerb stones at or near ground level to required line, level and curvature, jointed with cement mortar 1:3. The work shall include preparation, placement, joint finishing and drainage openings wherever required. Finished kerb edging shall be aligned, securely seated and checked for uniformity, curvature and proper drainage. |
| 364 | Providing and laying factory-made 60 mm thick M-30 grade cement concrete interlocking paver blocks of approved size, shape, colour and pattern over 50 mm thick compacted sand bed. The work shall include cutting, fitting, vibratory compaction, joint filling with fine sand and final sweeping. The completed paved surface shall be checked for levels, slope, interlocking, joint filling and surface regularity. |
| 365 | Providing, casting and fixing precast reinforced cement concrete covers/slabs of specified size and minimum 75 mm thickness, using cement concrete of grade M-25, including reinforcement with TMT steel bars of required diameter and spacing, centering/moulds, vibration, finishing, curing, lifting, loading, transportation, handling and placing in position over drain/inspection chamber/cable trench, including making provision for lifting hooks/holes wherever required, complete in all respects as directed by the Engineer-in-Charge. |
| 366 | Providing brick edging in full-brick width and half-brick depth along road/footpath edges, including excavation, laying, alignment, refilling and disposal of surplus earth within 50 m lead. Bricks shall be properly bedded and jointed to form a continuous edge restraint. The completed edging shall be checked for line, level, stability and interface with the pavement. |
| 367 | Providing, laying and jointing 200 mm diameter glazed stoneware pipe, Class SP-1, with stiff 1:1 cement mortar joints, including cutting, bedding, alignment and testing of joints. The work shall include all necessary labour, tools and minor accessories for complete installation. The pipeline shall be checked for line, level, gradient, joint tightness and leakage before backfilling. |
| 368 | Providing, laying and jointing 300 mm diameter glazed stoneware pipe, Class SP-1, with stiff 1:1 cement mortar joints, including cutting, bedding, alignment and testing of joints. The work shall include all necessary labour, tools and minor accessories for complete installation. The pipeline shall be checked for line, level, gradient, joint tightness and leakage before backfilling. |
| 369 | Providing and laying cement concrete 1:5:10 using 40 mm aggregate all around 150 mm diameter stoneware pipe, including bed concrete as per standard design. The work shall include preparation of trench bottom, placing and compacting concrete, maintaining pipe alignment and curing. The completed bedding/encasement shall provide uniform support without displacement of the pipe. |
| 370 | Providing and laying cement concrete 1:5:10 up to haunches of 150 mm diameter stoneware pipe including bed concrete as per standard design. The work shall include careful placement around the pipe, compaction without damaging joints and curing. Pipe line and gradient shall be rechecked before and after concrete placement. |
| 371 | Constructing brick masonry manhole of internal size 900 x 800 mm and 450 mm deep in cement mortar 1:4, including RCC top slab, foundation concrete 1:4:8, 12 mm internal plaster in 1:3 mortar, cement-finished channels in 1:2:4 concrete and light-duty CI cover/frame 455 x 610 mm. The item shall include all masonry, concrete, plaster, channel formation and finishing required for complete construction. The completed manhole shall be watertight, properly benched, aligned with connecting drains and provided with accessible cover. |
| 372 | Supplying and fixing 560 mm diameter heavy-duty CI manhole cover without frame, with minimum cover weight of 108 kg, suitable for industrial road/yard drainage applications. The item shall include seating, levelling and all necessary fixing/packing materials. The cover shall be securely seated, flush with finished pavement level and checked for stability and safe operation. |
| 373 | Providing and laying Non-Pressure NP-3 class medium-duty RCC pipe of 450 mm diameter including collars/spigot joints with stiff 1:2 cement mortar and testing of joints. The work shall include bedding, alignment, jointing and all necessary handling and installation accessories. The completed pipeline shall be checked for gradient, invert level, joint integrity and free flow before backfilling. |
| 374 | Providing and laying Non-Pressure NP-3 class medium-duty RCC pipe of 600 mm diameter including collars/spigot joints with stiff 1:2 cement mortar and testing of joints. The work shall include bedding, alignment, jointing and all necessary handling and installation accessories. The completed pipeline shall be checked for gradient, invert level, joint integrity and free flow before backfilling. |
| 375 | Constructing soak pit 1.20 x 1.20 x 1.20 m filled with brickbats including 100 mm diameter, 1.20 m long stoneware drain pipe and all associated work as per standard design. The item shall include excavation, filling, pipe connection and making good. The completed soak pit shall be checked for stability, inlet level and free discharge into the percolation zone. |
| 376 | Supplying and fixing 100 mm diameter stoneware intercepting trap in manholes using stiff 1:1 cement mortar, including all necessary joints, bedding, alignment and testing. The trap shall be installed at designed invert level and securely connected to incoming/outgoing drainage lines. The completed installation shall be tested for leakage, flow and proper trap operation. |
| 377 | Making bell-mouth opening/entrance of 100 x 50 x 50 cm for drainage pipe under footpath, including cement concrete 1:3:6, plastering, precast RCC/SFRC slab, cement-mortar finishing, centering, shuttering and neat cement punning inside the bell mouth. The work shall include complete shaping and integration with adjoining road/footpath. The completed opening shall be aligned with the drain inlet and finished to prevent water stagnation. |
| 378 | Supplying, fixing and installing white vitreous china Orissa-pattern Indian WC pan of 580 x 440 mm size, complete with integral foot rests, 100 mm P/S trap, 10-litre low-level PVC flushing cistern, flush pipe and operating fittings. The item shall include all necessary brackets, connectors, washers, sealing materials, clamps and fixing accessories required for a complete installation. The work shall include connection to the water-supply and soil/waste system, testing for leakage and proper flushing, and making good the adjoining surface. |
| 379 | Supplying, fixing and installing white vitreous china European WC complete with solid seat and lid, 10-litre low-level vitreous china flushing cistern, CP flush bend, brackets, overflow arrangement and mosquito-proof coupling. The item shall include all necessary fittings, connectors, washers, seals and fixing accessories for a complete and functional installation. The work shall include connection to water-supply and soil/waste piping, testing of flushing and leakage, and making good the installation area. |
| 380 | Supplying, fixing and installing white vitreous china flat-back wash basin of 630 x 450 mm size, complete with CI brackets, two 15 mm CP brass pillar taps and 32 mm CP brass waste fitting. The item shall include all necessary brackets, waste connections, flexible connections, washers, sealants and fixing hardware required for installation. The work shall include connection to water-supply and waste piping, testing for leakage and proper drainage, and making good the adjoining wall/floor surface. |
| 381 | Supplying, fixing and installing AISI 304 stainless-steel kitchen sink conforming to IS 13983, size 610 x 510 mm with 200 mm bowl depth, complete with CI brackets and 40 mm SS plug. The item shall include all necessary waste fittings, supports, sealants, clamps and fixing accessories required for a complete installation. The work shall include connection to water-supply and waste piping, testing for leakage and proper drainage, and making good the counter/wall/floor interface. |
| 382 | Supplying, fixing and installing 8 mm CP/SS health jet for European WC, complete with flexible tube up to 1 m long and SS triangular wall plate. The item shall include all necessary connectors, washers, wall fixing hardware and sealing materials required for a leak-free installation. The work shall include connection to the water-supply line, testing for leakage and spray operation, and making good the wall surface. |
| 383 | Supplying, fixing and installing a pair of white vitreous china foot rests for Indian squatting WC, each approximately 250 x 130 x 30 mm in size. The item shall include all necessary fixing materials, supports and accessories required for firm and level installation. The work shall include proper alignment with the WC pan, secure anchoring to the floor and making good the surrounding surface. |
| 384 | Supplying, fixing and installing 10-litre white PVC low-level flushing cistern complete with manually operated handle/lever and internal flushing fittings. The item shall include inlet valve, float assembly, flush valve, washers, connectors, flush pipe and all fixing accessories required for complete installation. The work shall include connection to the water-supply and WC pan, adjustment of the flushing mechanism, testing for leakage and proper flushing, and making good the wall surface. |
| 385 | Supplying, fixing and installing 10-litre white vitreous china low-level flushing cistern complete with controlled flushing mechanism and all internal fittings. The item shall include inlet valve, float arrangement, flush valve, connectors, flush pipe, washers and fixing hardware required for complete installation. The work shall include connection to the water-supply and WC pan, adjustment and testing of the flushing system for satisfactory operation and leakage-free performance, and making good the installation area. |
| 386 | Supplying, fixing and installing white solid-plastic WC seat and lid suitable for the specified pedestal WC pan, complete with hinges, buffers and fixing hardware. The item shall include all brackets, fasteners and accessories required for secure and aligned installation. The work shall include adjustment of the seat and lid for smooth operation, checking of stability and proper seating, and complete making good of the installation. |
| 387 | Supplying, fixing and connecting GI inlet connection for WC flush pipe, including cutting, threading and necessary fittings. The item shall include nipples, unions, washers, sealants and other accessories required for a leak-proof connection. The work shall include connection to the flushing cistern/WC arrangement, pressure testing for leakage and making good of the surrounding surface. |
| 388 | Supplying, fixing and installing 32 mm CP brass bottle trap of approved make and quality, complete with all necessary connections. The item shall include washers, nuts, seals, connectors and fixing accessories required for a complete waste connection. The work shall include connection to the wash basin/sink waste outlet and drainage pipe, testing for leakage and free discharge, and making good the adjoining surface. |
| 389 | Supplying, fixing and installing white vitreous china wall-mounted/flat-back lipped-front urinal basin of approved size and pattern, complete with fixing accessories. The item shall include necessary brackets, flushing-water connection, waste fitting, trap, connectors, washers and sealants required for complete installation. The work shall include connection to the water-supply and drainage system, testing for flushing, leakage and proper discharge, and making good the wall surface. |
| 390 | Supplying, fixing and installing white vitreous china squatting plate urinal with integral rim and longitudinal flushing pipe, complete with necessary fittings. The item shall include brackets, flushing connections, waste/trap connections, washers, sealants and fixing accessories required for complete installation. The work shall include connection to water-supply and drainage piping, testing of flushing and drainage performance, and making good the floor/wall surfaces. |
| 391 | Supplying, fixing and connecting 32 mm semi-rigid PVC waste pipe for wash basin/sink, including compatible PVC waste fittings and all accessories required for complete installation. The item shall include couplers, bends, connectors, washers, solvent/jointing materials and clamps as necessary. The work shall include connection between the sanitary fixture and drainage line, testing for leakage and free flow, and making good the adjoining surface. |
| 392 | Supplying, fixing and connecting 32 mm flexible PVC waste pipe for wash basin, including compatible PVC waste fittings and all necessary accessories. The item shall include connectors, clamps, washers, sealing materials and fixing hardware required for complete installation. The work shall include connection to the waste outlet and drainage system, testing for leakage and unobstructed discharge, and making good the surrounding surface. |
| 393 | Supplying, fixing and connecting 40 mm flexible PVC waste pipe for sink/urinal, including compatible PVC waste fittings and all necessary accessories. The item shall include connectors, clamps, washers, sealing materials and fixing hardware required for complete installation. The work shall include connection to the sanitary fixture and drainage line, testing for leakage and free discharge, and making good the adjoining surface. |
| 394 | Supplying, fixing and installing 100 mm sand-cast iron grating for gully trap, complete with fixing accessories. The item shall include frame/support, clamps, cement mortar or other approved fixing material and all minor accessories required for proper installation. The work shall include accurate alignment with the gully trap, secure fixing, checking for free drainage and making good the surrounding surface. |
| 395 | Supplying, fixing and installing 25 mm mosquito-proof coupling of approved municipal design, complete with all necessary fittings. The item shall include connectors, sealants, washers and fixing accessories required for a secure and hygienic connection. The work shall include connection to the relevant sanitary/drainage arrangement, checking for leakage and mosquito-proof sealing, and making good the installation area. |
| 396 | Supplying, fixing and installing 600 x 450 mm bevelled-edge 6 mm superior-quality glass mirror with hardboard backing, wooden cleats and CP brass screws/washers. The item shall include all necessary brackets, supports, fasteners, protective backing and accessories required for secure installation. The work shall include accurate leveling and alignment, firm fixing without damage to the mirror, and complete finishing of the adjoining wall surface. |
| 397 | Supplying, fixing and installing 600 x 120 x 5 mm glass shelf with rounded edges, anodised aluminium angle frame, CP brass brackets and guard rail. The item shall include all necessary supports, screws, plugs, brackets and fixing accessories required for a stable installation. The work shall include accurate leveling, secure anchoring to the wall, checking for stability and making good the fixing points. |
| 398 | Supplying, fixing and installing CP brass toilet-paper holder of approved pattern, complete with necessary concealed/open fixing hardware. The item shall include screws, plugs, brackets and other minor accessories required for secure installation. The work shall include proper alignment and firm fixing to the wall, checking for smooth operation and making good the fixing surface. |
| 399 | Supplying, fixing and installing vitreous china toilet-paper holder of approved pattern, complete with all necessary fixing accessories. The item shall include brackets, screws, plugs, sealants and other minor accessories required for secure installation. The work shall include proper alignment, firm fixing to the wall and making good the surrounding surface. |
| 400 | Supplying, fixing and installing self-cleansing sand-cast iron trap with 100 mm inlet and 75 mm outlet, complete with grating and vent arrangement as required. The item shall include all necessary collars, connectors, cement mortar, sealants and fixing accessories required for a complete installation. The work shall include connection to the drainage system, testing for water-tightness and free discharge, and making good the surrounding floor/wall. |
| 401 | Supplying, fixing and installing PTMT waste coupling for wash basin/sink, 31 mm diameter, complete with all necessary washers, nuts, seals and connection accessories. The item shall be securely connected to the sanitary fixture and waste pipe to ensure a leak-free joint. The work shall include testing for leakage and proper discharge and making good the installation as required. |
| 402 | Supplying, fixing and installing PTMT trapezoidal towel ring of approximately 215 x 200 mm size with concealed fixing arrangement. The item shall include all necessary brackets, screws, plugs and concealed fixing accessories required for secure installation. The work shall include accurate alignment, firm fixing and making good the wall surface. |
| 403 | Supplying, fixing and installing 600 mm long PTMT towel rail complete with brackets and concealed fixing arrangement. The item shall include screws, plugs, supports and all other minor fixing accessories required for secure installation. The work shall include accurate leveling, firm anchoring to the wall and making good the fixing points. |
| 404 | Supplying, fixing and installing PTMT shelf approximately 440 x 124 x 36 mm, of approved quality and colour, complete with fixing accessories. The item shall include brackets, screws, wall plugs and other minor hardware required for secure installation. The work shall include accurate leveling and alignment, firm fixing and making good the adjoining wall surface. |
| 405 | Supplying, fixing and installing PTMT 15 mm urinal spreader complete with 1/2-inch BSP threaded connection. The item shall include all necessary connectors, washers, sealants and fixing accessories required for a complete installation. The work shall include connection to the urinal flushing line, testing for leakage and uniform water distribution, and making good the surrounding surface. |
| 406 | Supplying, fixing and installing PTMT urinal cock of 15 mm bore with BSP female threaded connection, complete with accessories. The item shall include connectors, washers, sealants and fixing hardware required for a leak-free connection. The work shall include connection to the urinal water-supply line, testing for leakage and operation, and making good the installation area. |
| 407 | Supplying, fixing and installing cPVC pressure pipe for hot/cold water supply, 15 mm OD, internal work exposed on wall, including CPVC plain/brass threaded fittings, clamps at 1 m spacing, solvent-cement joints and testing., complete with all necessary fittings, joints, clamps, connectors, washers, sealants and fixing accessories required for a complete installation. The work shall include all cutting, threading/jointing, supports, connections and minor accessories necessary for proper integration with the water-supply system. The completed installation shall be tested for leakage and satisfactory operation at the required pressure, including making good all disturbed surfaces and leaving the work complete in all respects. |
| 408 | Supplying, fixing and installing cPVC pressure pipe for hot/cold water supply, 20 mm OD, internal work exposed on wall, including fittings, clamps, jointing and testing complete., complete with all necessary fittings, joints, clamps, connectors, washers, sealants and fixing accessories required for a complete installation. The work shall include all cutting, threading/jointing, supports, connections and minor accessories necessary for proper integration with the water-supply system. The completed installation shall be tested for leakage and satisfactory operation at the required pressure, including making good all disturbed surfaces and leaving the work complete in all respects. |
| 409 | Supplying, fixing and installing cPVC pressure pipe for hot/cold water supply, 25 mm OD, internal work exposed on wall, including fittings, clamps, jointing and testing complete., complete with all necessary fittings, joints, clamps, connectors, washers, sealants and fixing accessories required for a complete installation. The work shall include all cutting, threading/jointing, supports, connections and minor accessories necessary for proper integration with the water-supply system. The completed installation shall be tested for leakage and satisfactory operation at the required pressure, including making good all disturbed surfaces and leaving the work complete in all respects. |
| 410 | Supplying, fixing and installing cPVC pressure pipe for hot/cold water supply, 32 mm OD, internal work exposed on wall, including fittings, clamps, jointing and testing complete., complete with all necessary fittings, joints, clamps, connectors, washers, sealants and fixing accessories required for a complete installation. The work shall include all cutting, threading/jointing, supports, connections and minor accessories necessary for proper integration with the water-supply system. The completed installation shall be tested for leakage and satisfactory operation at the required pressure, including making good all disturbed surfaces and leaving the work complete in all respects. |
| 411 | Supplying, fixing and installing cPVC pressure pipe for hot/cold water supply, 40 mm OD, internal work exposed on wall, including fittings, clamps, jointing and testing complete., complete with all necessary fittings, joints, clamps, connectors, washers, sealants and fixing accessories required for a complete installation. The work shall include all cutting, threading/jointing, supports, connections and minor accessories necessary for proper integration with the water-supply system. The completed installation shall be tested for leakage and satisfactory operation at the required pressure, including making good all disturbed surfaces and leaving the work complete in all respects. |
| 412 | Supplying, fixing and installing cPVC pressure pipe for hot/cold water supply, 50 mm OD, internal work exposed on wall, including fittings, clamps, jointing and testing complete., complete with all necessary fittings, joints, clamps, connectors, washers, sealants and fixing accessories required for a complete installation. The work shall include all cutting, threading/jointing, supports, connections and minor accessories necessary for proper integration with the water-supply system. The completed installation shall be tested for leakage and satisfactory operation at the required pressure, including making good all disturbed surfaces and leaving the work complete in all respects. |
| 413 | Supplying, fixing and installing cPVC pressure pipe for hot/cold water supply, 15 mm OD, concealed internal work including cutting chases, making good, fittings, clamps, solvent-cement joints and testing., complete with all necessary fittings, joints, clamps, connectors, washers, sealants and fixing accessories required for a complete installation. The work shall include all cutting, threading/jointing, supports, connections and minor accessories necessary for proper integration with the water-supply system. The completed installation shall be tested for leakage and satisfactory operation at the required pressure, including making good all disturbed surfaces and leaving the work complete in all respects. |
| 414 | Supplying, fixing and installing cPVC pressure pipe for hot/cold water supply, 20 mm OD, concealed internal work including cutting chases, making good, fittings, clamps, jointing and testing., complete with all necessary fittings, joints, clamps, connectors, washers, sealants and fixing accessories required for a complete installation. The work shall include all cutting, threading/jointing, supports, connections and minor accessories necessary for proper integration with the water-supply system. The completed installation shall be tested for leakage and satisfactory operation at the required pressure, including making good all disturbed surfaces and leaving the work complete in all respects. |
| 415 | Supplying, fixing and installing cPVC pressure pipe for hot/cold water supply, 25 mm OD, concealed internal work including cutting chases, making good, fittings, clamps, jointing and testing., complete with all necessary fittings, joints, clamps, connectors, washers, sealants and fixing accessories required for a complete installation. The work shall include all cutting, threading/jointing, supports, connections and minor accessories necessary for proper integration with the water-supply system. The completed installation shall be tested for leakage and satisfactory operation at the required pressure, including making good all disturbed surfaces and leaving the work complete in all respects. |
| 416 | Supplying, fixing and installing cPVC pressure pipe for hot/cold water supply, 32 mm OD, concealed internal work including cutting chases, making good, fittings, clamps, jointing and testing., complete with all necessary fittings, joints, clamps, connectors, washers, sealants and fixing accessories required for a complete installation. The work shall include all cutting, threading/jointing, supports, connections and minor accessories necessary for proper integration with the water-supply system. The completed installation shall be tested for leakage and satisfactory operation at the required pressure, including making good all disturbed surfaces and leaving the work complete in all respects. |
| 417 | Supplying, fixing and installing cPVC pressure pipe for hot/cold water supply, 15 mm OD, external work including CPVC fittings, trenching/refilling, solvent-cement joints and testing., complete with all necessary fittings, joints, clamps, connectors, washers, sealants and fixing accessories required for a complete installation. The work shall include all cutting, threading/jointing, supports, connections and minor accessories necessary for proper integration with the water-supply system. The completed installation shall be tested for leakage and satisfactory operation at the required pressure, including making good all disturbed surfaces and leaving the work complete in all respects. |
| 418 | Supplying, fixing and installing cPVC pressure pipe for hot/cold water supply, 20 mm OD, external work including fittings, trenching/refilling, jointing and testing., complete with all necessary fittings, joints, clamps, connectors, washers, sealants and fixing accessories required for a complete installation. The work shall include all cutting, threading/jointing, supports, connections and minor accessories necessary for proper integration with the water-supply system. The completed installation shall be tested for leakage and satisfactory operation at the required pressure, including making good all disturbed surfaces and leaving the work complete in all respects. |
| 419 | Supplying, fixing and installing cPVC pressure pipe for hot/cold water supply, 25 mm OD, external work including fittings, trenching/refilling, jointing and testing., complete with all necessary fittings, joints, clamps, connectors, washers, sealants and fixing accessories required for a complete installation. The work shall include all cutting, threading/jointing, supports, connections and minor accessories necessary for proper integration with the water-supply system. The completed installation shall be tested for leakage and satisfactory operation at the required pressure, including making good all disturbed surfaces and leaving the work complete in all respects. |
| 420 | Supplying, fixing and installing cPVC pressure pipe for hot/cold water supply, 32 mm OD, external work including fittings, trenching/refilling, jointing and testing., complete with all necessary fittings, joints, clamps, connectors, washers, sealants and fixing accessories required for a complete installation. The work shall include all cutting, threading/jointing, supports, connections and minor accessories necessary for proper integration with the water-supply system. The completed installation shall be tested for leakage and satisfactory operation at the required pressure, including making good all disturbed surfaces and leaving the work complete in all respects. |
| 421 | Supplying, fixing and installing cPVC pressure pipe for hot/cold water supply, 40 mm OD, external work including fittings, trenching/refilling, jointing and testing., complete with all necessary fittings, joints, clamps, connectors, washers, sealants and fixing accessories required for a complete installation. The work shall include all cutting, threading/jointing, supports, connections and minor accessories necessary for proper integration with the water-supply system. The completed installation shall be tested for leakage and satisfactory operation at the required pressure, including making good all disturbed surfaces and leaving the work complete in all respects. |
| 422 | Supplying, fixing and installing cPVC pressure pipe for hot/cold water supply, 50 mm OD, external work including fittings, trenching/refilling, jointing and testing., complete with all necessary fittings, joints, clamps, connectors, washers, sealants and fixing accessories required for a complete installation. The work shall include all cutting, threading/jointing, supports, connections and minor accessories necessary for proper integration with the water-supply system. The completed installation shall be tested for leakage and satisfactory operation at the required pressure, including making good all disturbed surfaces and leaving the work complete in all respects. |
| 423 | Supplying, fixing and installing unplasticised PVC flexible connection pipe with brass unions, 15 mm bore, 30 cm long, complete., complete with all necessary fittings, joints, clamps, connectors, washers, sealants and fixing accessories required for a complete installation. The work shall include all cutting, threading/jointing, supports, connections and minor accessories necessary for proper integration with the water-supply system. The completed installation shall be tested for leakage and satisfactory operation at the required pressure, including making good all disturbed surfaces and leaving the work complete in all respects. |
| 424 | Supplying, fixing and installing unplasticised PVC flexible connection pipe with brass unions, 15 mm bore, 45 cm long, complete., complete with all necessary fittings, joints, clamps, connectors, washers, sealants and fixing accessories required for a complete installation. The work shall include all cutting, threading/jointing, supports, connections and minor accessories necessary for proper integration with the water-supply system. The completed installation shall be tested for leakage and satisfactory operation at the required pressure, including making good all disturbed surfaces and leaving the work complete in all respects. |
| 425 | Supplying, fixing and installing cP brass shower rose, 100 mm diameter, suitable for 15/20 mm inlet, complete with fixing., complete with all necessary fittings, joints, clamps, connectors, washers, sealants and fixing accessories required for a complete installation. The work shall include all cutting, threading/jointing, supports, connections and minor accessories necessary for proper integration with the water-supply system. The completed installation shall be tested for leakage and satisfactory operation at the required pressure, including making good all disturbed surfaces and leaving the work complete in all respects. |
| 426 | Supplying, fixing and installing cP brass shower rose, 150 mm diameter, suitable for 15/20 mm inlet, complete with fixing., complete with all necessary fittings, joints, clamps, connectors, washers, sealants and fixing accessories required for a complete installation. The work shall include all cutting, threading/jointing, supports, connections and minor accessories necessary for proper integration with the water-supply system. The completed installation shall be tested for leakage and satisfactory operation at the required pressure, including making good all disturbed surfaces and leaving the work complete in all respects. |
| 427 | Supplying, fixing and installing polyethylene water-storage tank conforming to IS 12701, with cover and locking arrangement and holes for inlet/outlet/overflow; excluding fittings and base support., complete with all necessary fittings, joints, clamps, connectors, washers, sealants and fixing accessories required for a complete installation. The work shall include all cutting, threading/jointing, supports, connections and minor accessories necessary for proper integration with the water-supply system. The completed installation shall be tested for leakage and satisfactory operation at the required pressure, including making good all disturbed surfaces and leaving the work complete in all respects. |
| 428 | Supplying, fixing and installing cP brass bib cock, 15 mm nominal bore, approved quality conforming to IS 8931, complete., complete with all necessary fittings, joints, clamps, connectors, washers, sealants and fixing accessories required for a complete installation. The work shall include all cutting, threading/jointing, supports, connections and minor accessories necessary for proper integration with the water-supply system. The completed installation shall be tested for leakage and satisfactory operation at the required pressure, including making good all disturbed surfaces and leaving the work complete in all respects. |
| 429 | Supplying, fixing and installing cP brass long-nose bib cock, 15 mm nominal bore, minimum 810 g, complete., complete with all necessary fittings, joints, clamps, connectors, washers, sealants and fixing accessories required for a complete installation. The work shall include all cutting, threading/jointing, supports, connections and minor accessories necessary for proper integration with the water-supply system. The completed installation shall be tested for leakage and satisfactory operation at the required pressure, including making good all disturbed surfaces and leaving the work complete in all respects. |
| 430 | Supplying, fixing and installing cP brass long-body bib cock, 15 mm nominal bore, minimum 690 g, complete., complete with all necessary fittings, joints, clamps, connectors, washers, sealants and fixing accessories required for a complete installation. The work shall include all cutting, threading/jointing, supports, connections and minor accessories necessary for proper integration with the water-supply system. The completed installation shall be tested for leakage and satisfactory operation at the required pressure, including making good all disturbed surfaces and leaving the work complete in all respects. |
| 431 | Supplying, fixing and installing cP brass concealed stop cock, 15 mm nominal bore, standard approved design conforming to IS 8931, complete., complete with all necessary fittings, joints, clamps, connectors, washers, sealants and fixing accessories required for a complete installation. The work shall include all cutting, threading/jointing, supports, connections and minor accessories necessary for proper integration with the water-supply system. The completed installation shall be tested for leakage and satisfactory operation at the required pressure, including making good all disturbed surfaces and leaving the work complete in all respects. |
| 432 | Supplying, fixing and installing cP brass angle valve for basin mixer/geyser point, 15 mm nominal bore, conforming to IS 8931, complete., complete with all necessary fittings, joints, clamps, connectors, washers, sealants and fixing accessories required for a complete installation. The work shall include all cutting, threading/jointing, supports, connections and minor accessories necessary for proper integration with the water-supply system. The completed installation shall be tested for leakage and satisfactory operation at the required pressure, including making good all disturbed surfaces and leaving the work complete in all respects. |
| 433 | Supplying, fixing and installing cP brass extension nipple, 15mmx50 mm, approved make/quality, complete., complete with all necessary fittings, joints, clamps, connectors, washers, sealants and fixing accessories required for a complete installation. The work shall include all cutting, threading/jointing, supports, connections and minor accessories necessary for proper integration with the water-supply system. The completed installation shall be tested for leakage and satisfactory operation at the required pressure, including making good all disturbed surfaces and leaving the work complete in all respects. |
| 434 | Supplying, fixing and installing pTMT bib cock, 15 mm bore, 86 mm long, minimum 88 g, approved quality/colour, complete., complete with all necessary fittings, joints, clamps, connectors, washers, sealants and fixing accessories required for a complete installation. The work shall include all cutting, threading/jointing, supports, connections and minor accessories necessary for proper integration with the water-supply system. The completed installation shall be tested for leakage and satisfactory operation at the required pressure, including making good all disturbed surfaces and leaving the work complete in all respects. |
| 435 | Supplying, fixing and installing pTMT concealed stop cock, 15 mm bore, 108 mm long, minimum 108 g, complete., complete with all necessary fittings, joints, clamps, connectors, washers, sealants and fixing accessories required for a complete installation. The work shall include all cutting, threading/jointing, supports, connections and minor accessories necessary for proper integration with the water-supply system. The completed installation shall be tested for leakage and satisfactory operation at the required pressure, including making good all disturbed surfaces and leaving the work complete in all respects. |
| 436 | Supplying, fixing and installing pTMT pillar cock, 15 mm bore, 125 mm long with foam-flow outlet, minimum 120 g, complete., complete with all necessary fittings, joints, clamps, connectors, washers, sealants and fixing accessories required for a complete installation. The work shall include all cutting, threading/jointing, supports, connections and minor accessories necessary for proper integration with the water-supply system. The completed installation shall be tested for leakage and satisfactory operation at the required pressure, including making good all disturbed surfaces and leaving the work complete in all respects. |
| 437 | Supplying, fixing and installing pTMT push cock, 15 mm bore, 98 mm long, minimum 75 g, complete., complete with all necessary fittings, joints, clamps, connectors, washers, sealants and fixing accessories required for a complete installation. The work shall include all cutting, threading/jointing, supports, connections and minor accessories necessary for proper integration with the water-supply system. The completed installation shall be tested for leakage and satisfactory operation at the required pressure, including making good all disturbed surfaces and leaving the work complete in all respects. |
| 438 | Supplying, fixing and installing circular PTMT floor/waste grating, 100 mm nominal diameter, approved quality/colour, complete., complete with all necessary fittings, joints, clamps, connectors, washers, sealants and fixing accessories required for a complete installation. The work shall include all cutting, threading/jointing, supports, connections and minor accessories necessary for proper integration with the water-supply system. The completed installation shall be tested for leakage and satisfactory operation at the required pressure, including making good all disturbed surfaces and leaving the work complete in all respects. |
| 439 | Supplying, fixing and installing circular PTMT floor/waste grating, 125 mm nominal diameter with 25 mm waste hole, complete., complete with all necessary fittings, joints, clamps, connectors, washers, sealants and fixing accessories required for a complete installation. The work shall include all cutting, threading/jointing, supports, connections and minor accessories necessary for proper integration with the water-supply system. The completed installation shall be tested for leakage and satisfactory operation at the required pressure, including making good all disturbed surfaces and leaving the work complete in all respects. |
| 440 | Supplying, fixing and installing pTMT ball cock with epoxy-coated aluminium rod and plastic float, 15 mm bore, complete., complete with all necessary fittings, joints, clamps, connectors, washers, sealants and fixing accessories required for a complete installation. The work shall include all cutting, threading/jointing, supports, connections and minor accessories necessary for proper integration with the water-supply system. The completed installation shall be tested for leakage and satisfactory operation at the required pressure, including making good all disturbed surfaces and leaving the work complete in all respects. |
| 441 | Supplying, fixing and installing pTMT angle stop cock, 15 mm nominal bore, minimum 85 g, complete., complete with all necessary fittings, joints, clamps, connectors, washers, sealants and fixing accessories required for a complete installation. The work shall include all cutting, threading/jointing, supports, connections and minor accessories necessary for proper integration with the water-supply system. The completed installation shall be tested for leakage and satisfactory operation at the required pressure, including making good all disturbed surfaces and leaving the work complete in all respects. |
| 442 | Supplying, fixing and installing pTMT swivelling shower, 15 mm nominal bore, minimum 40 g, complete., complete with all necessary fittings, joints, clamps, connectors, washers, sealants and fixing accessories required for a complete installation. The work shall include all cutting, threading/jointing, supports, connections and minor accessories necessary for proper integration with the water-supply system. The completed installation shall be tested for leakage and satisfactory operation at the required pressure, including making good all disturbed surfaces and leaving the work complete in all respects. |
| 443 | Supplying, fixing and installing pTMT soap-dish holder, approx. 138x102x75 mm, concealed fixing arrangement, minimum 106 g, complete., complete with all necessary fittings, joints, clamps, connectors, washers, sealants and fixing accessories required for a complete installation. The work shall include all cutting, threading/jointing, supports, connections and minor accessories necessary for proper integration with the water-supply system. The completed installation shall be tested for leakage and satisfactory operation at the required pressure, including making good all disturbed surfaces and leaving the work complete in all respects. |
| 444 | Supplying, fixing and installing enclosed bulk water meter, 80 mm nominal bore, conforming to IS 2373, including bolts, nuts and rubber insertions; tail pieces excluded., complete with all necessary fittings, joints, clamps, connectors, washers, sealants and fixing accessories required for a complete installation. The work shall include all cutting, threading/jointing, supports, connections and minor accessories necessary for proper integration with the water-supply system. The completed installation shall be tested for leakage and satisfactory operation at the required pressure, including making good all disturbed surfaces and leaving the work complete in all respects. |
| 445 | Supplying, fixing and installing enclosed bulk water meter, 100 mm nominal bore, conforming to IS 2373, including bolts, nuts and rubber insertions; tail pieces excluded., complete with all necessary fittings, joints, clamps, connectors, washers, sealants and fixing accessories required for a complete installation. The work shall include all cutting, threading/jointing, supports, connections and minor accessories necessary for proper integration with the water-supply system. The completed installation shall be tested for leakage and satisfactory operation at the required pressure, including making good all disturbed surfaces and leaving the work complete in all respects. |
| 446 | Supplying, fixing and installing gI water-supply pipe, 15 mm nominal bore, internal exposed work, including GI fittings, clamps, cutting and making good walls, complete., complete with all necessary fittings, joints, clamps, connectors, washers, sealants and fixing accessories required for a complete installation. The work shall include all cutting, threading/jointing, supports, connections and minor accessories necessary for proper integration with the water-supply system. The completed installation shall be tested for leakage and satisfactory operation at the required pressure, including making good all disturbed surfaces and leaving the work complete in all respects. |
| 447 | Supplying, fixing and installing gI water-supply pipe, 20 mm nominal bore, internal exposed work, including GI fittings, clamps, cutting and making good walls, complete., complete with all necessary fittings, joints, clamps, connectors, washers, sealants and fixing accessories required for a complete installation. The work shall include all cutting, threading/jointing, supports, connections and minor accessories necessary for proper integration with the water-supply system. The completed installation shall be tested for leakage and satisfactory operation at the required pressure, including making good all disturbed surfaces and leaving the work complete in all respects. |
| 448 | Supplying, fixing and installing gI water-supply pipe, 25 mm nominal bore, internal exposed work, including GI fittings, clamps, cutting and making good walls, complete., complete with all necessary fittings, joints, clamps, connectors, washers, sealants and fixing accessories required for a complete installation. The work shall include all cutting, threading/jointing, supports, connections and minor accessories necessary for proper integration with the water-supply system. The completed installation shall be tested for leakage and satisfactory operation at the required pressure, including making good all disturbed surfaces and leaving the work complete in all respects. |
| 449 | Supplying, fixing and installing gI water-supply pipe, 15 mm nominal bore, concealed internal work, including GI fittings/clamps, anti-corrosive coating, cutting chases and making good, complete., complete with all necessary fittings, joints, clamps, connectors, washers, sealants and fixing accessories required for a complete installation. The work shall include all cutting, threading/jointing, supports, connections and minor accessories necessary for proper integration with the water-supply system. The completed installation shall be tested for leakage and satisfactory operation at the required pressure, including making good all disturbed surfaces and leaving the work complete in all respects. |
| 450 | Supplying, fixing and installing gI water-supply pipe, 20 mm nominal bore, concealed internal work, including GI fittings/clamps, anti-corrosive coating, cutting chases and making good, complete., complete with all necessary fittings, joints, clamps, connectors, washers, sealants and fixing accessories required for a complete installation. The work shall include all cutting, threading/jointing, supports, connections and minor accessories necessary for proper integration with the water-supply system. The completed installation shall be tested for leakage and satisfactory operation at the required pressure, including making good all disturbed surfaces and leaving the work complete in all respects. |
| 451 | Supplying, fixing and installing gI water-supply pipe, 15 mm nominal bore, external work, including GI fittings, trenching, refilling and testing, complete., complete with all necessary fittings, joints, clamps, connectors, washers, sealants and fixing accessories required for a complete installation. The work shall include all cutting, threading/jointing, supports, connections and minor accessories necessary for proper integration with the water-supply system. The completed installation shall be tested for leakage and satisfactory operation at the required pressure, including making good all disturbed surfaces and leaving the work complete in all respects. |
| 452 | Supplying, fixing and installing gI water-supply pipe, 20 mm nominal bore, external work, including GI fittings, trenching, refilling and testing, complete., complete with all necessary fittings, joints, clamps, connectors, washers, sealants and fixing accessories required for a complete installation. The work shall include all cutting, threading/jointing, supports, connections and minor accessories necessary for proper integration with the water-supply system. The completed installation shall be tested for leakage and satisfactory operation at the required pressure, including making good all disturbed surfaces and leaving the work complete in all respects. |
| 453 | Supplying, fixing and installing gun-metal gate valve with CI wheel, 20 mm nominal bore, screwed end, approved quality, complete., complete with all necessary fittings, joints, clamps, connectors, washers, sealants and fixing accessories required for a complete installation. The work shall include all cutting, threading/jointing, supports, connections and minor accessories necessary for proper integration with the water-supply system. The completed installation shall be tested for leakage and satisfactory operation at the required pressure, including making good all disturbed surfaces and leaving the work complete in all respects. |
| 454 | Supplying, fixing and installing gun-metal gate valve with CI wheel, 25 mm nominal bore, screwed end, approved quality, complete., complete with all necessary fittings, joints, clamps, connectors, washers, sealants and fixing accessories required for a complete installation. The work shall include all cutting, threading/jointing, supports, connections and minor accessories necessary for proper integration with the water-supply system. The completed installation shall be tested for leakage and satisfactory operation at the required pressure, including making good all disturbed surfaces and leaving the work complete in all respects. |
| 455 | Supplying, fixing and installing gun-metal gate valve with CI wheel, 32 mm nominal bore, screwed end, approved quality, complete., complete with all necessary fittings, joints, clamps, connectors, washers, sealants and fixing accessories required for a complete installation. The work shall include all cutting, threading/jointing, supports, connections and minor accessories necessary for proper integration with the water-supply system. The completed installation shall be tested for leakage and satisfactory operation at the required pressure, including making good all disturbed surfaces and leaving the work complete in all respects. |
| 456 | Supplying, fixing and installing brass ball valve with plastic float, 15 mm nominal bore, high/low pressure type, complete., complete with all necessary fittings, joints, clamps, connectors, washers, sealants and fixing accessories required for a complete installation. The work shall include all cutting, threading/jointing, supports, connections and minor accessories necessary for proper integration with the water-supply system. The completed installation shall be tested for leakage and satisfactory operation at the required pressure, including making good all disturbed surfaces and leaving the work complete in all respects. |
| 457 | Supplying, fixing and installing brass ball valve with plastic float, 20 mm nominal bore, high/low pressure type, complete., complete with all necessary fittings, joints, clamps, connectors, washers, sealants and fixing accessories required for a complete installation. The work shall include all cutting, threading/jointing, supports, connections and minor accessories necessary for proper integration with the water-supply system. The completed installation shall be tested for leakage and satisfactory operation at the required pressure, including making good all disturbed surfaces and leaving the work complete in all respects. |
| 458 | Supplying, laying, fixing and connecting glazed stoneware sewer pipe, 100 mm diameter, class SP-1, laid and jointed with 1:1 cement mortar including testing of joints, complete., complete with all necessary collars, joints, mortar, sealants, supports and connection accessories. The work shall include excavation/cutting where required, proper alignment, gradient, jointing and connection to the adjoining drainage system, including all incidental works. The completed installation shall be tested for water-tightness and free flow, with trenches/surfaces refilled or made good and the entire work completed to the satisfaction of the Engineer-in-Charge. |
| 459 | Supplying, laying, fixing and connecting glazed stoneware sewer pipe, 150 mm diameter, class SP-1, laid and jointed with 1:1 cement mortar including testing of joints, complete., complete with all necessary collars, joints, mortar, sealants, supports and connection accessories. The work shall include excavation/cutting where required, proper alignment, gradient, jointing and connection to the adjoining drainage system, including all incidental works. The completed installation shall be tested for water-tightness and free flow, with trenches/surfaces refilled or made good and the entire work completed to the satisfaction of the Engineer-in-Charge. |
| 460 | Supplying, laying, fixing and connecting non-pressure NP2 class light-duty RCC pipe, 100 mm diameter, with collars and cement-mortar joints, including testing, complete., complete with all necessary collars, joints, mortar, sealants, supports and connection accessories. The work shall include excavation/cutting where required, proper alignment, gradient, jointing and connection to the adjoining drainage system, including all incidental works. The completed installation shall be tested for water-tightness and free flow, with trenches/surfaces refilled or made good and the entire work completed to the satisfaction of the Engineer-in-Charge. |
| 461 | Supplying, laying, fixing and connecting non-pressure NP2 class light-duty RCC pipe, 150 mm diameter, with collars and cement-mortar joints, including testing, complete., complete with all necessary collars, joints, mortar, sealants, supports and connection accessories. The work shall include excavation/cutting where required, proper alignment, gradient, jointing and connection to the adjoining drainage system, including all incidental works. The completed installation shall be tested for water-tightness and free flow, with trenches/surfaces refilled or made good and the entire work completed to the satisfaction of the Engineer-in-Charge. |
| 462 | Group A light/fan/exhaust-fan/call-bell point with 1.5 sq.mm FRLS/HFFR PVC insulated copper conductor single-core cable in surface/recessed medium-class PVC conduit, with modular switch, modular plate, suitable GI box and 1.5 sq.mm earth conductor. |
| 463 | Twin-control light point with 1.5 sq.mm FRLS/HFFR PVC insulated copper conductor single-core cable in surface/recessed medium-class PVC conduit, complete with two-way modular/piano switches, box, plate and earth conductor. |
| 464 | Light/power plug wiring with 2 x 4 sq.mm FRLS/HFFR PVC insulated copper single-core conductors in surface/recessed medium-class PVC conduit, along with 1 x 4 sq.mm copper earth conductor. |
| 465 | Circuit/sub-main wiring comprising 2 x 1.5 sq.mm FRLS/HFFR PVC insulated copper single-core conductors plus 1 x 1.5 sq.mm earth conductor in surface/recessed medium-class PVC conduit. |
| 466 | Three-phase circuit/sub-main wiring comprising 4 x 2.5 sq.mm FRLS/HFFR PVC insulated copper single-core conductors plus 2 x 2.5 sq.mm earth conductors in surface/recessed medium-class PVC conduit. |
| 467 | Supplying, fixing and installing 20 mm steel conduit in surface/recessed installation, complete with all approved accessories, couplers, bends, inspection fittings and supports. Surface conduits shall be painted and recessed conduits shall include cutting/chasing and making good. The completed system shall be checked for alignment, continuity and clear passage before wiring. |
| 468 | Supplying, fixing and installing 25 mm steel conduit in surface/recessed installation, complete with all approved accessories, couplers, bends, inspection fittings and supports. Surface conduits shall be painted and recessed conduits shall include cutting/chasing and making good. The completed system shall be checked for alignment, continuity and clear passage before wiring. |
| 469 | Supplying, fixing and installing 32 mm steel conduit in surface/recessed installation, complete with all approved accessories, couplers, bends, inspection fittings and supports. Surface conduits shall be painted and recessed conduits shall include cutting/chasing and making good. The completed system shall be checked for alignment, continuity and clear passage before wiring. |
| 470 | Supplying, fixing and installing 40 mm steel conduit in surface/recessed installation, complete with all approved accessories, couplers, bends, inspection fittings and supports. Surface conduits shall be painted and recessed conduits shall include cutting/chasing and making good. The completed system shall be checked for alignment, continuity and clear passage before wiring. |
| 471 | Supplying, fixing and installing 20 mm medium-class PVC conduit in surface/recessed installation, complete with bends, couplers, junctions, inspection fittings and all necessary accessories. The work shall include cutting/chasing where required, saddling/supporting and making good. The completed conduit shall be checked for alignment, continuity and clear passage before drawing wires. |
| 472 | Supplying, fixing and installing 25 mm medium-class PVC conduit in surface/recessed installation, complete with bends, couplers, junctions, inspection fittings and all necessary accessories. The work shall include cutting/chasing where required, saddling/supporting and making good. The completed conduit shall be checked for alignment, continuity and clear passage before drawing wires. |
| 473 | Supplying, fixing and installing 32 mm medium-class PVC conduit in surface/recessed installation, complete with bends, couplers, junctions, inspection fittings and all necessary accessories. The work shall include cutting/chasing where required, saddling/supporting and making good. The completed conduit shall be checked for alignment, continuity and clear passage before drawing wires. |
| 474 | Supplying, fixing and installing 40 mm medium-class PVC conduit in surface/recessed installation, complete with bends, couplers, junctions, inspection fittings and all necessary accessories. The work shall include cutting/chasing where required, saddling/supporting and making good. The completed conduit shall be checked for alignment, continuity and clear passage before drawing wires. |
| 475 | Supplying, fixing and installing 75 x 75 x 60 mm nominal metal electrical box with suitable phenolic laminated cover, complete with screws, supports and accessories. The box shall be accurately aligned and securely fixed for switches/junctions. Metallic boxes shall be bonded to earth where required and all disturbed surfaces shall be made good. |
| 476 | Supplying, fixing and installing 100 x 100 x 60 mm nominal metal electrical box with suitable phenolic laminated cover, complete with screws, supports and accessories. The box shall be accurately aligned and securely fixed for switches/junctions. Metallic boxes shall be bonded to earth where required and all disturbed surfaces shall be made good. |
| 477 | Supplying, fixing and connecting 5/6 A modular switch on existing modular plate and switch box, complete with terminals and required accessories. The work shall include secure fixing, interconnections and all minor consumables required for a complete installation. The switch shall be tested for mechanical operation, continuity and correct polarity. |
| 478 | Supplying, fixing and connecting 15/16 A modular switch on existing modular plate and switch box, complete with terminals and required accessories. The work shall include secure fixing, interconnections and all minor consumables required for a complete installation. The switch shall be tested for mechanical operation, continuity and correct polarity. |
| 479 | Supplying, fixing and connecting 3-pin 5/6 A modular socket outlet on existing modular plate and switch box, complete with terminals and accessories. The work shall include protective earthing, connections and fixing hardware. The socket shall be tested for polarity, earth continuity, insulation resistance and satisfactory operation. |
| 480 | Supplying, fixing and connecting 6-pin 15/16 A modular socket outlet on existing modular plate and switch box, complete with terminals and accessories. The work shall include protective earthing, connections and fixing hardware. The socket shall be tested for polarity, earth continuity, insulation resistance and satisfactory operation. |
| 481 | Supplying, fixing and connecting suitable-size GI box with modular plate and cover, including 6-pin 5/6 & 15/16 A modular socket outlet and 15/16 A modular switch. The item shall include internal connections, earthing, fixing hardware and all accessories required for complete installation. The assembly shall be tested for polarity, earth continuity, insulation resistance and satisfactory operation. |
| 482 | Supplying, fixing and connecting 3-pin 5 A ceiling rose on existing junction box/wooden block, complete with terminals and accessories. The item shall include all fixing hardware and electrical connections required for complete installation. The ceiling rose shall be checked for secure fixing, continuity and correct polarity. |
| 483 | Supplying, fixing and connecting brass batten/angle holder, complete with terminals and required accessories. The item shall include secure fixing, electrical connections and all minor consumables necessary for complete installation. The holder shall be tested for continuity, polarity and secure mechanical operation. |
| 484 | Supplying, fixing and connecting suitable-size GI box with modular plate and cover, including 2 Nos. 3-pin 5/6 A modular socket outlets and 2 Nos. 5/6 A modular switches for light plugs in non-residential buildings. The item shall include internal wiring, earthing, terminals and all fixing accessories. The complete assembly shall be tested for polarity, earth continuity, insulation resistance and satisfactory operation. |
| 485 | Supplying, installing and commissioning GI pipe earthing using 40 mm dia, 4.5 m long GI earth pipe, complete with accessories, masonry enclosure, lockable cover, watering pipe, charcoal/coke and salt. The item shall include excavation, electrode connection, watering arrangement and backfilling. Earth resistance shall be measured and recorded and the completed earth pit shall be left accessible for maintenance. |
| 486 | Supplying and laying 25 x 5 mm copper strip at approximately 0.50 m below ground as strip earth electrode, including connection/termination with nuts, bolts, spring washers and required overlapping joints. The work shall include proper routing, jointing, supports and connection to the earth electrode/equipment. The completed earth path shall be tested for continuity and earth resistance and all disturbed surfaces made good. |
| 487 | Supplying, installing, testing and commissioning 12–15 W LED recessed/surface SMD downlighter, complete with aluminium body, PMMA/prismatic diffuser, high-efficiency driver, surge and short/open-circuit protection, PF ≥0.95 and associated external connections. The item shall include 1.5 sq.mm FRLS/HFFR copper connection, earthing, mounting hardware and all accessories. The fitting shall be tested for illumination, electrical safety and satisfactory operation. |
| 488 | Supplying, installing, testing and commissioning 18 W LED recessed/surface SMD downlighter, complete with aluminium body, PMMA/prismatic diffuser, high-efficiency driver, surge and short/open-circuit protection, PF ≥0.95 and associated external connections. The item shall include 1.5 sq.mm FRLS/HFFR copper connection, earthing, mounting hardware and all accessories. The fitting shall be tested for illumination, electrical safety and satisfactory operation. |
| 489 | Supplying, installing, testing and commissioning 40 W LED surface-mounted batten light with replaceable driver, suitable aluminium/CRCA body, high-efficiency LED system and complete external connections. The item shall include 1.5 sq.mm FRLS/HFFR copper connection, earthing, mounting clips and all accessories required for complete installation. The fitting shall be tested for illumination, electrical safety and satisfactory operation. |
| 490 | Providing and laying integral cement based water proofing treatment including preparation of surface as required for treatment of roofs, balconies, terraces etc consisting of following operations:(a) Applying a slurry coat of neat cement using 2.75 kg/sqm of cement admixed with water proofing compound conforming to IS. 2645 and approved by Engineer-in-charge over the RCC slab including adjoining walls upto 300 mm height including cleaning the surface before treatment.(b) Laying brick bats with mortar using broken bricks/brick bats 25 mm to 115 mm size with 50% of cement mortar 1:5 (1 cement : 5 coarse sand) admixed with water proofing compound conforming to IS : 2645 and approved by Engineer-in-charge over 20 mm thick layer of cement mortar of mix 1:5 (1 cement :5 coarse sand ) admixed with water proofing compound conforming to IS : 2645 and approved by Engineer-in-charge to required slope and treating similarly the adjoining walls upto 300 mm height including rounding of junctions of walls and slabs.(c) After two days of proper curing applying a second coat of cement slurry using 2.75 kg/ sqm of cement admixed with water proofing compound conforming to IS : 2645 and approved by Engineer-in-charge.(d) Finishing the surface with 20 mm thick jointless cement mortar of mix 1:4 (1 cement :4 coarse sand) admixed with water proofing compound conforming to IS : 2645 and approved by Engineer-in-charge including laying glass fibre cloth of approved quality in top layer of plaster and finally finishing the surface with trowel with neat cement slurry and making pattern of 300x300 mm square 3 mm deep.(e) The whole terrace so finished shall be flooded with water for a minimum period of two weeks for curing and for final test.“All above operations to be done in order and as directed and specified by the Engineer-in-Charge :With average thickness of 120 mm and minimum thickness at khurra as 65 mm. |
| 491 | Providing and laying water proofing treatment in sunken portion of WCs, bathroom etc., by applying cement slurry mixed with water proofing cement compound consisting of applying :(a) First layer of slurry of cement @ 0.488 kg/sqm mixed with water proofing cement compound @ 0.253 kg/ sqm. This layer will be allowed to air cure for 4 hours.(b) Second layer of slurry of cement @ 0.242 kg/sqm mixed with water proofing cement compound @ 0.126 kg/sqm. This layer will be allowed to air cure for 4 hours followed with water curing for 48 hours.The rate includes preparation of surface, treatment and sealing of all joints, corners, junctions of pipes and masonry with polymer mixed slurry. |
| 492 | PROVIDING AND APPLYING WATER PROOFING: Providing and applying approved waterproofing treatment to RCC tunnel walls, comprising thorough surface preparation, treatment of cracks, honeycombs and construction joints, localised sealing of seepage/leakage points as required, and application of approved multi-coat polymer-modified cementitious/crystalline waterproofing coating, complete in all respects as per manufacturer’s specifications and directions of the Engineer-in-Charge. |
| 493 | PROVIDING AND APPLYING WATER PROOFING: Providing and Apply Waterproofing: carrying out water proofing works wherever required as Per the Waterproofing Standards. Integral Cement Waterproofing Compound Confirming to IS 2645 and of approved make and manufacture enlisted by the site in-charge from time to time shall be used. The contractor shall bring the materials to the site in their original packing. The containers will be opened and the material mixed with dry cement in the proportion by weight,recommended by the manufacturers or as specifically described in the description of the item. care shall be taken in mixing, to see that the water proofing material gets well and integrally mixed with the cement and does not run out separately when water is added. Rate to include Additional 50mm PCC layer in 1:1.5:3 mix which is to be done to maintain the slop. |
| 494 | Providing and laying APP (Atactic Polypropylene Polymer) modified prefabricated five layer, 3 mm thick waterproofing membrane, black finished, reinforced with glass fibre matt, consisting of a coat of bitumen primer for bitumen membrane @ 0.40 litre/sqm, manufactured by the same membrane manufacturer, having density at 25°C of 0.87–0.89 kg/litre and viscosity 70–160 cps. Over the primer coat, the membrane shall be laid using butane torch, sealing all joints/laps and preparing the surface complete. The membrane shall have the specified physical and chemical properties, including joint strength, tear strength, softening point and cold flexibility. |
| 495 | Providing and injecting approved low-viscosity epoxy injection grout of approved make into cracks, voids and honeycombed portions of reinforced cement concrete/masonry by suitable mechanical injection gun/pump at the pressure required to ensure complete penetration and filling of the cracks/voids, including cleaning and preparation of the affected surface, drilling of injection holes at suitable spacing, fixing of injection nipples/packers, sealing of cracks between nipples with approved epoxy sealing compound, injection of epoxy grout under controlled pressure, monitoring of grout flow and pressure, cutting/removal of nipples/packers after completion and curing, sealing and making good the injection holes and treated surface, including all materials, labour, tools, tackles, plant and equipment, complete in all respects as directed by the Engineer-in-Charge. Payment shall be made on the basis of the actual weight of approved grout injected. |
| 496 | Providing and laying lightweight sunken slab filling using approved brick bats/brick ballast and cement mortar or other approved filling material to required levels, including slope formation and compaction. The work shall include filling around sanitary pipes without damaging waterproofing or pipe joints. Finished filling shall provide stable support and proper levels for subsequent floor construction. |
| 497 | Providing and fixing factory-made steel door shutter of approved gauge and profile, including steel frame, hinges, holdfasts/anchor fasteners, tower bolts, lock, handles and necessary hardware. The shutter and frame shall be accurately fabricated, aligned, plumbed and securely fixed to masonry/RCC openings. The complete door shall be tested for smooth operation, proper closing, locking and uniform clearances.Providing and fixing 1 mm thick M.S. sheet door with frame of 40x40x6 mm angle iron and 3 mm M.S. gusset plates at the junctions and corners, all necessary fittings complete, including applying a priming coat of approved steel primer.Using M.S. angels 40x40x6 mm for diagonal braces |
| 498 | Providing and fixing factory-made steel door shutter of approved gauge and profile, including steel frame, hinges, holdfasts/anchor fasteners, tower bolts, lock, handles and necessary hardware. The shutter and frame shall be accurately fabricated, aligned, plumbed and securely fixed to masonry/RCC openings. The complete door shall be tested for smooth operation, proper closing, locking and uniform clearances.Providing and fixing 1 mm thick M.S. sheet door with frame of 40x40x6 mm angle iron and 3 mm M.S. gusset plates at the junctions and corners, all necessary fittings complete, including applying a priming coat of approved steel primer.Using flats 30x6 mm for diagonal braces and central cross piece |
| 499 | Providing and fixing pressed steel door frames conforming to IS: 4351, manufactured from commercial mild steel sheet of 1.60 mm thickness, including hinges, jamb, lock jamb, bead and if required angle threshold of mild steel angle of section 50x25 mm, or base ties of 1.60 mm, pressedmild steel welded or rigidly fixed together by mechanical means, including M.S. pressed butt hinges 2.5 mm thick with mortar guards, lock strikeplate and shock absorbers as specified and applying a coat of approved steel primer after pre-treatment of the surface as directed by Engineer-in-charge: Fixing with adjustable lugs with split end tail to each jamb |
| 500 | Providing and fixing pressed steel door frames conforming to IS: 4351, manufactured from commercial mild steel sheet of 1.60 mm thickness, including hinges, jamb, lock jamb, bead and if required angle threshold of mild steel angle of section 50x25 mm, or base ties of 1.60 mm, pressedmild steel welded or rigidly fixed together by mechanical means, including M.S. pressed butt hinges 2.5 mm thick with mortar guards, lock strikeplate and shock absorbers as specified and applying a coat of approved steel primer after pre-treatment of the surface as directed by Engineer-in-charge: Fixing with carbon steel galvanised dash fastener of required dia and size |
| 501 | Providing and applying solvent-free, high-build polyurethane (PU) floor coating below and around electrical panels, of approved make, over properly prepared concrete surface, including mechanical cleaning/grinding, removal of loose particles and dust, surface preparation, application of compatible primer and minimum two coats of PU coating to achieve a minimum dry film thickness of 1.0 mm, including all materials, labour, tools and tackles, complete as per manufacturer's specifications and direction of Engineer-in-Charge. |
| 502 | Site GradingCarrying out grading of existing site surface in areas specified by the Engineer-in-Charge/HPCL, including near facilities, beside roads and other designated locations, by carrying out necessary cutting, filling, leveling and dressing of the existing ground to achieve the required finished levels and slopes. The work shall include deployment of required manpower, tools, tackles and machinery; excavation/cutting of existing earth, shifting and carting of available earth to low-lying areas, spreading and dressing of existing/imported earth, watering and compaction as required, and all incidental works necessary to achieve a smooth, uniform and properly compacted finished surface, free from undulations, depressions and unevenness, complete as directed by HPCL/Engineer-in-Charge.The maximum depth of cutting/filling under this item shall generally be up to 300 mm. Filling and leveling exceeding 400 mm depth/height shall be measured and paid separately under the applicable item. Supply of earth is excluded from the scope; wherever additional earth is required for leveling, the same shall be measured and paid separately under the applicable item.The rate shall include all manpower, machinery, equipment, handling, shifting, leveling, dressing, watering, compaction and associated operations necessary for complete execution of the work. |
| 503 | FALSE FLOORING:The false flooring system shall comprise galvanized mild-steel pedestal base plates, threaded pedestal studs, adjustable pressure die-cast aluminium top heads, and galvanized steel channel stringers forming a 610 mm × 610 mm support grid to achieve a finished floor level of 700 mm above the existing floor. The 35 mm thick, 610 mm × 610 mm teakwood particle-board panels shall be finished with aluminium foil underside, 2 mm antistatic PVC tiles/high-pressure laminate on top, and hard PVC edge lipping, with aluminium cleats for lateral stability. Panels shall be properly leveled, aligned, individually removable, and provided with necessary cutouts, ramps, slopes, steps and additional pedestals around equipment cutouts as required. The cavity shall be cleaned, dust-free and coated with polyurethane, and the complete system shall be designed to withstand a distributed load of 1250 kg/m². All detailed specifications, materials, dimensions, installation requirements, and associated provisions are as specified and detailed within this tender document itself. |
| 504 | SUPPLY & FIXING OF MS/CARBON STEEL FOUNDATION BOLTS & NUTS:Providing, supplying, fabricating and fixing MS/Carbon Steel round foundation/holding-down bolts of specified diameter and length, conforming to IS 2062 or equivalent approved grade, complete with nuts, washers, washer plates, threading, cutting, bending/hooking, welding, templates, positioning, alignment and fixing in RCC foundations/pedestals, including all materials, fabrication, labour, tools & tackles, transportation, testing/certification and all incidental works, complete as per approved drawings, specifications and directions of Engineer-in-Charge. Cost of concrete casting works shall be paid separately. |
| 505 | SUPPLY & FIXING OF HOT-DIP GALVANISED FOUNDATION BOLTS & NUTS :Supplying and fixing of BOLTS & NUTS as per IS: 2062 / SAE 1018 with minimum yield strength of 250 MPA in concrete at all levels and positions, bolts with nuts and washers, pipe sleeves etc. including surface cleaning & galvanizing with zinc coating of 610 GSM or 85 micron minimum conforming to IS: 4759, providing grease to exposed area of bolts, welding wherever necessary, protecting the same till final erection complete as per drawing, specifications and instruction of Engineer-in-Charge. Cost of concrete casting works shall be paid separately. |
| 506 | FIXING OF FOUNDATION BOLTS:Fixing, alignment and positioning of foundation bolts of approved size and grade at all levels and positions, including nuts, washers, pipe sleeves, templates/supports, necessary temporary arrangements for maintaining correct line, level, spacing and projection, providing grease to exposed portions of bolts, welding wherever necessary and protecting the same till final erection is completed, complete as per approved drawings, specifications and instructions of Engineer-in-Charge.Cost of concrete casting works shall be paid separately. Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Sep 26, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedOct 19, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 19 daysOct 20, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 20 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender