Tender For Repairs To Plain Cement Concrete Hardstanding, Boundary Wall, Replacement Of Damaged Precast Reinforced Cement Concrete Slab And Manhole Cover And Other Connected Misc B/R Items At maintenance of (Mb) Ghatkopar Under Ge (Nw) Bhandup
Tender Value
35.80 Lakhs
Estimated cost
Bid Submission
17 Oct 2026
14 days left
EMD
71600
Bank guarantee accepted
Document Fee
500
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Mumbai Suburban → Maharashtra
EMD Exemption
Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for Repairs To Plain Cement Concrete Hardstanding, Boundary Wall, Replacement Of Damaged Precast Reinforced Cement Concrete Slab And Manhole Cover And Other Connected Misc B/R Items At maintenance of (Mb) Ghatkopar Under Ge (Nw) Bhandup
BOQ
| Sl. No. | Item Description |
| 1 | Demolition of brick work or stone / boulder masonry, built in cement mortar or cement lime mortar including all quoins, arches, pillars etc but excluding ashlar facing dressed stone work and precast concrete articles complete all as specified and directed. |
| 2 | Dismantling structural steel work including doors, gates but excluding framed truss etc complete all as specified and directed by Engineer-in-Charge. |
| 3 | Demolition of cement concrete (un-reinforced) in ground floors and pavings not exceeding 15 cm thickness below or above ground level complete all as specified and directed. |
| 4 | Dismantling of old barbed wire fencing with concertina coil complete all as specified and directed by Engineer-in-Charge. |
| 5 | Dismantling Plain or corrugated steel sheeting, any gauge, thickness, including Nainital or similar pattern roof coverings complete all as specified and directed. |
| 6 | Taking down cement plaster including racking out joints, hacking for key & scrubbing down with water etc complete all as specified and directed. |
| 7 | M & L for PCC (1:4:8) type D2 using 40 mm graded aggregate as in foundation mass concrete complete all as specified and directed by Engineer-in-Charge. |
| 8 | M & L for brick work with fly ash bricks old size bricks in cement mortar, straight or curved on plan exceeding 6 m mean radius, built in CM (1:6) complete all as specified and as directed |
| 9 | M & L for providing cement concrete type C2 (1:2:4) (20 mm graded aggregate) in surface channels and drains complete all as specified and as directed. |
| 10 | M & L for PCC (1:2:4) type B1 for copings on brick wall surfaces including weathering, slightly rounded or chamferred angles and throating complete all as specified and as directed. |
| 11 | M & L for 100 mm thick cement concrete (1:2:4) type B-1 using 20 mm graded stone aggregate in flooring finishes the surfaces even and smooth without using extra cement etc complete all as specified and directed. |
| 12 | M & L for 25 mm thick PCC (1:2:4) type B0, using 12.5 mm graded aggregate as in floors to receive surface of tile complete all as specified and directed. |
| 13 | M & L for screed bed or bedding layer of mortar, 20 mm thick, in cement mortar (1:6), for laying floor finishes / tiles complete all as specified and directed. |
| 14 | M & L in repairs for coloured glazed chequered liquid finish cement concrete 30 cm x 30 cm x 25 mm thick with mixture of grey and white cement in equal proportions and no pigment set & jointed in neat cement slurry & pointed in coloured cement to match the shade of tiles complete all as specified and directed. |
| 15 | M & L for 75 mm thick PCC (1:4:8) type D-2 using 40 mm graded stone aggregate as in sub base floor / pavings complete all as specified and directed |
| 16 | M & L for sand filling under 25 mm floors or in foundation including watering and consolidation complete all as specified and directed. |
| 17 | M & L in repairs for machine pressed (LAQUER FINISH) cement concrete factory made coloured glazed interlocking paver block any shape and size confirming to IS 15658 -2006 of 80 mm thickness, M-40 Grade, machine pressed of pattern and colour as approved by GE complete all as specified and directed. |
| 18 | M & L in repairs for machine pressed (LAQUER FINISH) cement concrete factory made coloured glazed interlocking paver block any shape and size confirming to IS 15658 - 2006 of 60 mm thickness, M-35 Grade, machine pressed of pattern and colour as approved by GE complete all as specified and directed. |
| 19 | M & L for coloured endura tiles of size 30 cm x 30 cm x 20 mm thick with mixture of grey and white cement in equal proportions and no pigment set & jointed in neat cement slurry & pointed in coloured cement to match the shade of tiles complete all as specified and directed. |
| 20 | M & L for PCC (1:2:4) type B1 using 20mm graded aggregate for machine pressesd precast cement concrete kerb stone including weathering, slightly rounded or chemfered angles and throating, as directed edges complete including excavavtion for kerb stone complete all as specified and as directed. |
| 21 | M & L in repairs for providing factory made RCC precast cement concrete grade M-30 cover slab of size 450 mm x 900 mm x 75 mm thick size set in cement mortar (1:6) including reinforcement of 8 mm dia deformed bars @150mm c/c both ways etc, complete all as specified and directed. |
| 22 | M & L in repairs for providing factory made RCC precast cement concrete grade M-30 cover slab of size 600 mm x 900 mm x 75 mm thick size set in cement mortar (1:6) including reinforcement of 8 mm dia deformed bars @150mm c/c both ways etc, complete all as specified and directed. |
| 23 | S & F in repair MS steel work in tubular trusses for sign board posts including special shaped washer etc. complete using ERW or induction butt welded tubes conforming to I.S 1161-1979 grade St.-240, complete all as specified as directed |
| 24 | S & F welded steel wire fabric weight not exceeding 4 kg/sqm supplied and fixed to wood or steel members complete all as specified and directed. |
| 25 | S & F pre-coated galvalume aluminium zinc coating based corrugated steel sheet 0.50 mm thick of any colour having tensile strength of 550 mpa as in roof covering / cladding to wall, fixed with self tapping screws complete all as specified and directed |
| 26 | M & L for cement concrete (1:4:8) type D-2 using 40 mm graded stone aggregate in foundation and filling around fencing post complete all as specified & directed. (Deduction for the portion of fencing post / strut embeded in concrete shall be made) |
| 27 | M & L in repairs for 18-20 mm thick Granite of any colour (table rubbed and polished) as in windows cill, in steps, jambs, pillars, window cills, cooking platforms and like in cement mortar (1:4) including form work, pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite with full round bull nosing edging complete all as specified and as directed |
| 28 | S & F mild steel grills framed work as such as grills, gratings etc., with ends of bars shouldered and / or riveted, or forget into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways, MS railings framework of water tanks and similar work conforming to Fe 410-0 or FE 310-0 complete all as specified and directed. |
| 29 | S & F 1.25 mm thick Mild steel, plain black sheet in steel gates and similar work, cut to size, holes punched; including round headed screws, clout nails or rivets and fixed to wood or steel framing with plain 40 mm lap joints with riveted or welded seams, including bending or turning up, mitred angles etc as required complete including cutting out of existing sheet if required complete all as specified and as directed. |
| 30 | S & F framed work as in doors or gates of angle or other section with gusset plates, rails, braces, etc., complete, drilled for fixing of steel sheeting or other covering, doors etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings and fastening and fixing complete FE 290 Gde E-165 complete all as specified and directed. |
| 31 | M & L in repair for reinforced cement concrete M-30 (20 mm graded aggregates) (nominal mix) as in drain cover slabs supported on wall with cast in situ including form work (width of drain not exceeding 3.0 mtr) including dismantling complete all as specified and directed. Reinforcement to be measured & paid seperately under respective items. |
| 32 | Supply and fixing TMT bars, 10 mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with mild steel wire (annealed) but not less than 0.9 mm dia conforming to Fe-410 - 0, complete all as specified and directed. |
| 33 | M & L for 15 mm thick in CM (1:4) rendering on fair faces of brick work is to be finished even and smooth (without using extra cement) complete all as specified and as directed. |
| 34 | M & L for preparing newly plastered walls surfaces and applying two coats of cement base paint over a coat white wash complete all as specified and directed. |
| 35 | M & L for preparation of new steel surfaces exceeding 10 cm width or girth and applying two coats of synthetic enamel paint over one coat of red oxide of zinc chrome primer complete all as specified and directed. |
| 36 | M & L for precast cement concrete block masonry in PCC (1:3:6) type C1 with solid block exceeding 10 cm in width and setting in CM (1:6) complete all as specified and as directed. |
| 37 | M & L for walling of random rubble masonry uncoursed well bonded and built in cement mortar (1:6) complete all as specified and directed . |
| 38 | All as per item no. 37 above but with old stone masonary (except stone) complete all as specified and directed. |
| 39 | M & L for extra over stone walling for hammer dressing to face stones and dressing of face beds and joints in random rubble walling, uncoursed with maximum depression 40 mm on face from straight edge of granite or trap stone of face bed & joints as specified of random ruble walling uncoursed or brought up to course complete all as specified and directed . |
| 40 | Racking out joints / pointing to random rubble or polygonal rubble uncoursed or brought up to courses built in cement mortar complete all as specified and directed. |
| 41 | M & L for raised pointing to random rubble or polygonal rubble uncoursed masonry in CM (1:4) complete all as specified and directed. |
| 42 | M & L for providing precast cement concrete (1:2:4) type B-1 (using 20 mm greded aggregate) in window or door cills, lintels, bressumers, steps, quoin blocks (for use with masonry), string courses, copings, kneelers, apex stones, pier caps, columns, posts, boundary pillars, bed plates, pintle blocks, anchorage blocks, bonders (for stonelling), corbels, brackets etc. (of any section indicated), with plain fair faces, including chamfered, weatherings, throating etc. and setting in mortar complete with joints to match complete all as specified and directed. |
| 43 | M & L for 20 mm thick broken glass coping in cement morter (1:3) on top of wall complete all as specified and directed. |
| 44 | M & L in repairs for reinforced concrete pipes class NP-2, 450 mm dia laid and jointed complete with collars complete all as specifed and directed. |
| 45 | S & F in repair stainless steel railing special alloy (grade 304) pipe 1.50 mm thick and any dia of pipe, including necessary cutting, notching organ welding, grinding and drlling counter sunk holes and bending required shape by mechanical means in factory as per requirement without forming wrinkles and butting polishing complete all as specified and directed. |
| 46 | S & F in repair WPC charcoal interlocking wall paneling / ceilling (LOUVERS SEAMLESS DESIGNER PLANKS) any colour high grade PVC, 100% termite & water resistant for 12-20 mm thick fixing with SS clips, bolt or adhesive with aluminium framing / grid with suitable fittings complete all as specified and directed. |
| 47 | M & L hardcore of broken stone or boulders of gauge not exceeding 63 mm, deposited, spread and levelled in layers not exceeding 15 cm thick, watered and rammed to true surface complete all as specified and directed. |
| 48 | M & L for M20 design mix (1:1.5:3) type B2 using 20 mm graded aggregate for flooring of stages complete all as specified. The cement used should be of OPC 43 / 53 grade and work should be commenced only after prior approval of the design mix with RMC plant mentioned in the PS clause. Before placing M20 grade of concrete including all shuttering and supporting to maintain proper box as bay wise with MS sections as directed by Engineer-in-Charge. |
| 49 | M & L for preparation of old plastered or unplastered surface of walls, cornices etc by brooming down or steel wire brushing scrapping down smoke soot, moulds moss and efflorescent salts and trading oil and greasy spots including all necessary scaffolding and applying one coat cement base paint (white or tinted) complete all as specified and directed. |
| 50 | S & F razer type concertina coil, 9 SWG hot galvanied spring tensile wire 145 to 150 newton per square mm, zinc coating 250-300 gram per sqm dia of coil when unstretched 610 mm minimum no of coil 10 per RM affter laying hot dip galvanised razer ribbon tape of size 0.50 mm thick 19 mm wide before wrapping of central corewise fixed with 1.66 mm thk GI clips 25 nos per running meter and special nut bolt hold Z coil together and extra two rows parrel wire of 10 gauge complete all as specified and directed by EIC and dismantling of razer type concertina coil with two parallel rows of wire remove of the debris outside MD land complete all as specified and directed by Engineer-in-Charge. |
| 51 | S & F galvanised 2 strand steel barbed wire 2.24 mm dia barbed with 2 mm dia barbs at 75 mm spacing and straining and fixing to any type of standard rails, straining bolts including securing of typing at crossings with provision of galvanised mild steel wire staple or steel pin as directed (each line of wire to be measured) complete all as specified and directed. Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Sep 26, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedOct 17, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 14 daysOct 19, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 16 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender