Tender For Special Repair To Building No T-216 And Allied Works At Cijw School Vairengte
Tender Value
39.90 Lakhs
Estimated cost
Bid Submission
19 Oct 2026
16 days left
EMD
79800
Bank guarantee accepted
Document Fee
500
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Kolasib → Mizoram
EMD Exemption
Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender For Special Repair To Building No T-216 And Allied Works At Cijw School Vairengte
BOQ
| Sl. No. | Item Description |
| 1 | B & R Division Items |
| 2 | Demolition of un-reinforced cement concrete in ground floor and paving not exceeding 15 cm thick (below or above ground level) complete all as specified and directed. |
| 3 | Demolition of reinforced cement concrete floors (other than ground floors), beams, staircases, landing, chajjas and similar suspended work complete all as specified and directed. |
| 4 | Demolition of brick work or stone/ boulder masonry, built in cement mortar including all quoins, pillars etc. complete all as specified and as directed. |
| 5 | Demolition of reed lathing, single or double including battens and plaster or chiken wire lathing all as specified. |
| 6 | Dismantling mild steel work or wrought iron of any description and in any position complete all as specified and as directed. |
| 7 | Dismantling plain or corrugated steel sheeting, any gauge or any thickness as in roof covering, wall cladding, etc.including all necessary staging / scaffolding, etc. as required complete all as specified and as directed. |
| 8 | Dismantling of timber scantling 40 Sqcm and over in section, in any position in unframed work complete all as specified and directed. |
| 9 | Dismantling wall and ceiling boards (fibre, pulb, insulation etc) or insulation boards slabs/blankets any thickness including cover fillets all as specified and as directed. |
| 10 | Dismantling boarding any description fixed in any position with nails all as specified. |
| 11 | Taking down cement plaster on brick or stone walls etc, including raking out joints, hacking for key scrubing down with water etc complete all as specified and as directed. |
| 12 | Taking down chowkhats or frame with shutters (without taking off shutters from frame) each not exceeding 1.50 Sqm each complete all as specified. |
| 13 | Taking down Chowkhats or frames with shutters exceeding 1.5 Sqm but not exceeding 4 Sqm each (without taking off shutters from the frame) complete all as specified. |
| 14 | Excavating in trenches, n exc 1.50 m wide and n exc 1.5 m in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. n exc 10 sq m on plan and n exc 1.5 m in depth and getting out soft/ loose type of soil complete all as specified and directed. |
| 15 | Returning, filling in trenches including spreading, leveling watering and ramming in layers not exceeding 25cm all as specified. |
| 16 | Removing of surplus soil not exceeding 50 m and deposited where directed at a level not exceeding 1.50m above the starting point all as specified. |
| 17 | M&L for PCC (1:4:8), Type D2 using 40 mm graded stone aggregate as in foundations, sub-base,filling and mass concrete complete all as specified. |
| 18 | M & L for 75mm thick plain cement concrete 1:3:6 type C-2 (using 40mm graded stone aggregates) as in plinth protection finished over and smooth without using extra cement complete all as specified and dirceted |
| 19 | Use and waste formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams; and similar work; vertical or to batter rough finished flat surfaces of concrete complete all as specified and as directed. |
| 20 | Use and waste of formwork to sides of pillars, posts, struts, piers, columns and stanchions for rough finished flat surfaces of concrete all as specified and directed. |
| 21 | Use and waste formwork to sides and soffits of floor or roof beam, beam hunching, girder, lintels, cantilever, shelves including supports etc for rough finished flat surfaces of concrete complete all as specified and directed |
| 22 | Use and waste of formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200mm thick (Horizontal or sloping) complete all as specified and directed |
| 23 | Material and labour for Reinforced Cement Concrete M-20 (design mix) using 20 mm graded aggregate as in foundation including rafts, footings, foundation beams, plinth beams, bases for columns etc complete all as specified and directed. |
| 24 | Material and labour for Reinforced Cement Concrete M-25 (design mix) using 20 mm graded aggregate as in column, pillars, piers, posts, and struts complete all as specified and directed. |
| 25 | Material and labour for Reinforced Cement Concrete M-25 (design mix) using 20 mm graded aggregate as in beams, cantilever, lintels over 1.5m complete all as specified and directed. |
| 26 | Material and labour for Reinforced Cement Concrete M-25 (design mix) using 20 mm graded aggregate as in slab supported on walls, beams and columns in floors, roof landig balconies, canopies, deck slab and shelves and like complete all as specified and directed. |
| 27 | M & L for Mild steel TMT Bars 10mm dia and over, cut to length bend to shape as required including cranking, hooking etc and binding with and including mild steel wire (annealed) not less than 0.9 mm dia complete all as specified and directed. |
| 28 | M & L for Mild steel TMT Bars 6mm to 8mm dia , cut to length bend to shape as required including cranking, hooking etc and binding with and including mild steel wire (annealed) not less than 0.9 mm dia complete all as specified and directed. |
| 29 | M & L for Mild Steel TMT Bar 6mm dia and over up to 10 mm dia as in stirrups, spacers and binders as required including cranking, hooking etc and binding with and including mild steel wire (annealed) not less than 0.9 mm dia complete all as specified and directed |
| 30 | M & L for brickwork with subclass 'B' old size brick straight or curved on plan exc 6 m mean raduis, built in CM (1:6) complete all as specified and directed. |
| 31 | M & L for half brick work with Subclass ‘B’ old size brick straight or curved on plan to radius built in cement mortar (1:4) complete all as specified . |
| 32 | M & L for 15 mm thick rendering in cement mortar 1:6 on fair faces of brick wall or concrete surfaces, finished the surfaces even and fair without using extra cement complete all as specified. |
| 33 | M & L rendering 15 mm thick cement mortar 1:4 on fair faces of brickwork or concrete surfaces mixed with water proofing compound @ 3% weight of cement complete all as specified. (Note :WPC measured separately). |
| 34 | Supply only integral water proofing compound WPC complete all as specified. |
| 35 | M&L Machine cut pre polished kota stone slab flooring 20-25mm thick over 15mm thick screed bed in cm 1 : 6 with cement slurry jointed and pointed with grey cement slurry mixed with pigment to match the shade of slab as in flooring including rubbing and mirror/granite finish complete all as specified and as directed. |
| 36 | M&L Machine cut pre polished kota stone in riser of steps, skirting, dado and pillar 20-25mm thick over 20mm thick screed bed in cm 1 : 3 with cement slurry @ 4 kg/sqm jointed and pointed with grey cement slurry mixed with pigment to match the shade of slab including rubbing and mirror/granite finish complete all as specified and as directed. |
| 37 | Supply and fix pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and as directed. |
| 38 | Supply and fix pre-painted galvalume aluminium zinc coating GI based plain steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and as directed. |
| 39 | M & L for eves gutter made with 1mm thick MS sheet galvanised, class 3, half rounded edges complete all as specified and as directed. |
| 40 | Supply and fix Framed work such as grills, gratings, etc.. with ends of bars or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe.290.Gde-E-165 complete all as specified and directed. |
| 41 | Supply and fix mild steel Plates (plain or chequered) (Fe-290, Gde E-165) cut to required size, forming holes to receive holding down bolt and welded to tubular/square hollow section truss at both ends complete all as specified. |
| 42 | Supply and fix structural steel work in tubular/hollow sections trusses , Purlin, posts, rafter etc including special shaped washer etc. complete using ERW or induction butt welded tubes conforming to IS 1161-1979 grade St.-240 complete all as as specified and directed. |
| 43 | S & F anodised aluminium frame for doors, windows, ventilators with one or more rebates including jointing cleat for fixing etc complete all as specified . |
| 44 | Supply and fix anodised Aluminium door shutters, aluminium section weighing 0.55 kg/m including necessary joining cleats, glazing clips, ruber neoprene packing, handles 2 nos in each door, hinges, anodised aluminium snap bedading screws etc complete all as specified. |
| 45 | M & L for 12 mm thick Prelaminated particle board,Exterior grade, prelaminated on both side with decorative choice lamination & other side balancing white lamination, all as directed. |
| 46 | Supply and fix 3 ways sliding anodized aluminium glazed window shutter with frame with the following specification all as specified & directed.(a) Window frame 3 track of size 95mm × 25mm × 1.5mm thick.(b) Stiles and rails of size 35mm × 25mm × 1.5mm.(c) 35mm × 35mm × 1.5mm T section mullion.(d) PVC gasket with 4mm thick tinted glass, incl. aluminium handles with necessary locking arrangement for 02 Nos glazed shutter.(e) Stainless steel wire cloth, 0.36 mm nominal dia of wire and average width of aperture 1.40 mm, fixed with stainless steel wire staples, incl. aluminium handles with necessary locking arrangement for 01 No gauzed shutter.Note: Measurement to be taken as overall width and height of window. No shutter or frame to be measured separately. All necessary accessories including tinted glass and stainless steel wire cloth required for assembling and fixing window at proper place complete are deemed to be inclusive. |
| 47 | S&F 4.8 mm thick tinted sheet glass ordinary quality and glazing with oil putting square nexc 0.5 sqm in each pane complete all as specified. |
| 48 | Supply and fix 150 mm long aluminum anodised barrel tower bolts of extruded section complete all as specified and directed. |
| 49 | Supply and fix 200 mm long aluminum anodised barrel tower bolts of extruded section complete all as specified and directed. |
| 50 | S&F Mortice lock, vertical type size 100mm, of aluminium body 04 levers vertical type complete all as specified. |
| 51 | Supply and fix 300mm long Aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed complete all as specified. |
| 52 | S&F Door closer hydraulically regulated aluminium body (die cast body), designation no. 3 universal type, suitable for door shutters of 851 to 1000mm in width and weight between 61 to 80kg complete all as specified and directed |
| 53 | S & F as in repair 25mm dia MS chromium plated curtain rods with brackets including fixing stops, rollers bracket etc with harrison rails all as specified and directed . |
| 54 | Supply & Fixing False ceiling with semi perforated 12 mm thick micro tegular edged or 10 mm thick square edge at all heights with GRG (Glass Fiber Reinforced Gypsum) false ceiling tiles of size 595 × 595 mm of approved texture design and pattern having moisture content less than 2%, humidity resistance of 99%, NCR 0.50 to 0.75 as per IS 8225 : 1987, non-combustible as per BS 475 (Part-IV) 1970 and light code description Unit Rate No. 429, Sub Head 26.0 – New Technologies and Material, reflectance of 85% minimum, laid in true horizontal level, suspended on interlocking metal T-grid of hot dipped galvanized iron section of 0.33 mm thick (galvanized @ 120 gms/sqm including both sides) comprising of:Main T runner of size 15 × 32 mm, length 3000 mm.Cross T of size 15 × 32 mm, length 1200 mm.Secondary intermediate cross T of size 15 × 32 mm, length 600 mm.To form grid module of size 600 × 600 mm, suspended from ceiling using galvanized metal sheet item (galvanized @ 80 gms/sqm), i.e. 50 mm long, 8 mm outer diameter M-6 fasteners, 6 mm dia fully threaded hanger rod up to 1000 mm length, and L-shape level adjusters of size 85 × 25 mm, galvanized iron perimeter wall angle of size 24 × 24 × 0.40 mm, length 3000 mm, to be fixed on perimeter of wall/partition with the help of plastic rawl plugs at 450 mm centre to centre and 40 mm long drywall screws.The work shall be carried out as per specification, drawing and as per direction of Engr-in-Charge |
| 55 | M & L for preparation of new plastered surface and applying two coats of acrylic distemper over one coat of alkali resistant primer over including 1mm thick wall care putty over plastered surface complete all as specified and directed |
| 56 | M & L for preparation of new plastered surface and applying two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm using roller complete all as specified and directed. |
| 57 | M & L for Preparation of new steel surfaces surfaces of any description, over 10cm in width or girth, not otherwise described and applying two coats of synthetic enamel paint over including a coat of red oxide chrome primer of surfaces complete all as specified. |
| 58 | E & M Division items |
| 59 | Taking down carefully copper/aluminium point wiring (light, fan, buzzer, socket or power) complete including fixture and fittings such as switches, ceiling roses, pendants, regulators, sockets, light fitting etc including removing from site for taking credit and making good to disturbed surface of walls, floors etc as per existing specification complete all as specified and as directed. |
| 60 | Taking down carefully submain wiring including all accessories without disturbing existing wiring fittings fixtures etc and making good to the disturbed surfaces all as directed and as specified in any type and size all as directed. |
| 61 | Dismantling old unserviceable main switches, sheet metal enclosures DB including MCBs etc and removing from site for taking credit incl making good to disturbed surface of wall as per existing specification complete all as specified and as directed. |
| 62 | M & L for point wiring with FRLSH stranded copper conductor 1.5 sqmm (nominal area), two single core, PVC insulated cable 1100 volts grade, ISI-694 marked in and including heavy duty,concealed PVC Conduit including all accessories etc ISI marked, with GI sunken box suitable for fixing switches, sockets and regulators including PVC insulated stranded copper conductor 1.5 sqmm (nominal area) single core cable as earth continuity conductor to common earth and connecting to earth dolly complete all as specified and directed for One light point controlled by one switch. |
| 63 | M & L for point wiring with FRLSH stranded copper conductor 1.5 sqmm (nominal area), two single core, PVC insulated cable 1100 volts grade, ISI-694 marked in and including heavy duty, concealed PVC Conduit including all accessories etc ISI marked, with GI sunken box suitable for fixing switches, sockets and regulators including PVC insulated stranded copper conductor 1.5 sqmm (nominal area) single core cable as earth continuity conductor to common earth and connecting to earth dolly complete all as specified and directed for One fan point/exhaust fan point controlled by one, one way switch . |
| 64 | M & L for point wiring with FRLSH stranded copper conductor 1.5 sqmm (nominal area), two single core, PVC insulated cable 1100 volts grade, ISI-694 marked in and including heavy duty, concealed PVC Conduit including all accessories etc ISI marked, with GI sunken box suitable for fixing switches, sockets and regulators including PVC insulated stranded copper conductor 1.5 sqmm (nominal area) single core cable as earth continuity conductor to common earth and connecting to earth dolly complete all as specified and directed for One 3 pin 5 Amp socket outlet point controlled by one switch on the same board. |
| 65 | M & L for point wiring with FRLSH stranded copper conductor 1.5 sqmm (nominal area), two single core, PVC insulated cable 1100 volts grade, ISI-694 marked in and including heavy duty, PVC Conduit including all accessories etc ISI marked, with GI sunken box suitable for fixing switches, sockets and regulators including PVC insulated stranded copper conductor 1.5 sqmm (nominal area) single core cable as earth continuity conductor to common earth and connecting to earth dolly complete all as specified and directed for One 3 pin 5 Amp socket outlet point controlled by one switch on independent board. |
| 66 | M & L for point wiring with FRLSH stranded copper conductor 2.5 sqmm (nominal area), two single core, PVC insulated cable 1100 volts grade, ISI-694 marked in and including heavy duty, PVC Conduit including all accessories etc ISI marked, with GI sunken box suitable for fixing switches, sockets and regulators including PVC insulated stranded copper conductor 2.5 sqmm (nominal area) single core cable as earth continuity conductor to common earth and connecting to earth dolly complete all as specified and directed for 3 pin, 15 Amp socket outlet, independent |
| 67 | S&F switch piano flush type button single pole one way 5 Amps all as specified and directed. |
| 68 | S&F socket outlet 2 in 1, 3 pin 5 Amp flush type all as specified and directed. |
| 69 | S&F switch socket combination 5 in 1 5/16 Amp flush type with all as specified and directed. |
| 70 | S&F ceiling rose surface bakelite with three terminals all as specified and directed |
| 71 | S&F ceiling fan regulator socketed, step type, flush type heavy duty suitable to work on 230 volts AC supply complete all as specified. |
| 72 | S&F lamp holder insulated body with back plate for batten fitting complete all as specified and directed. |
| 73 | M & L for submain wiring with two single core 6.0 sqmm PVC insulated unsheathed cable multi-strand copper conductor FRLSH drawn through and including PVC non metallic rigid Conduit conceled with all fittings and fixing accessories on roof, walls, ceiling etc including 1 x 6.0 sqmm PVC insulated unsheathed multi strand copper conductor earth wire FRLSH connecting earth including cutting groove for concealed wiring, making good to disturb surface of wall/floor with cement mortar and finishes to match existing complete all as specified and directed. Note: Two run of single core cable, one run earth wire and one run PVC Conduit will be measured as one length. |
| 74 | S & F LED light fitting 1x9W/1X10W bulkhead luminaires including LED light driver holder connecting up with three core flexible copper conductor cable of suitable size all as specified and directed. |
| 75 | Supply & Fix LED type down lighter recess type 36W size 600mm X 600mm , complete with drivers connecting accessories and provision of fixing arrangement in false ceiling complete all as specified. |
| 76 | Supply and fixing surface mounting batten tube light fitting 20watt capacity, integrated polycarbonate LED channel with white acrylic cover complete suitable for and including Lamp 1X20 Watt, (4 feet) fixed properly on wall surface and connecting complete from ceiling rose to fitting by three core copper conductor cable of overall sheathed size 2.5 Sqmm which shall be passed through PVC flexible conduit complete all as specified and directed. |
| 77 | S&F bldg security light, LED luminaire 25 watt IP 66 LED lamp, made up of pressure die cast alluminium body with mid power LED as lighting sources and PC cover having Top opening separate driver compartment with IP66 protection and impact resistance of IK07 including fixing arrangements and taking down old rusted bracket fittings complete all as per directed by Engr- in – charge. Make : Bajaj or equivalent make of Havells/M/S Jaquar & company pvt ltd. |
| 78 | S&F plastic body exhaust fan 250mm sweep complete with louvers shutter, voltage 230V, 50 Hz, RPM 1200, copper winding and connecting to ceiling rose with flexible copper cable including making holes on the wall and making good to the disturbed surfaces complete all as specified and as directed. |
| 79 | S&F BLDC ceiling fan 1200mm sweep complete with blades, down rods and accessories, 230 V, min air delivery 210 CFM with service value 6.00 BEE 5 star rated & provn of ‘S’ type fan hook including taking down of old UNSV one and depositing to MES storeyard for keeping in safe custody complete all as specified and directed including one step type electronic regulator. |
| 80 | S&F Factory made distribution board sheet metal enclosure powder coated single phase neutral (SPN) 8 way double door with Aluminum bus bar 100 Amp for fixing of MCBs including grouting on the wall by means of screws and rawal plugs and making good disturbed surfaces complete all as specified and directed. |
| 81 | S&F Factory made distribution board sheet metal enclosure powder coated single phase neutral (SPN) 4 way double door with Aluminum bus bar 100 Amp for fixing of MCBs including grouting on the wall by means of screws and rawal plugs and making good disturbed surfaces complete all as specified and directed. |
| 82 | S&F Factory made distribution board sheet metal enclosure powder coated triple phase neutral (TPN) 4 way double door with Aluminum bus bar 100 Amp for fixing of MCBs including grouting on the wall by means of screws and rawal plugs and making good disturbed surfaces complete all as specified and directed. |
| 83 | S&F MCB TPN of capacity 63 Amps, 240 V, 10 KA 'B' curve complete all as specified and directed. |
| 84 | S&F MCB SPN of capacity 40-63 Amps, 240 V, 10 KA 'C' curve complete all as specified and directed. |
| 85 | S&F MCB SP of capacity 5-32 Amps, 240 V, 10 KA 'C' curve complete all as specified and directed. Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Sep 26, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedOct 19, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 16 daysOct 22, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 19 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender