Tender For Special Repair Of Fol Shed Building No. A/9/90 At Asc (Sup) Type C At Pms Under Ge Panagarh
Tender Value
48.25 Lakhs
Estimated cost
Bid Submission
16 Oct 2026
12 days left
EMD
96500
Bank guarantee accepted
Document Fee
500
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Purba Bardhaman → West Bengal
EMD Exemption
Not Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender For Special Repair Of Fol Shed Building No. A/9/90 At Asc (Sup) Type C At Pms Under Ge Panagarh
BOQ
| Sl. No. | Item Description |
| 1 | Demolition of cement concrete (un reinforced) in ground floors and paving n.exc 15cm thickness (below or above ground (level) and lowering if necessary, removal of the rubbish off the premises Complete all as specified and directed. |
| 2 | M & L for Cement concrete 100 mm thick type B- 1, 1:2:4 (20 mm graded aggregate) laid on concrete floors and pavings; laid over cement concrete subfloors etc. and finished to an even and rough surface as specified and as directed by Engg-in-charge. |
| 3 | M&L for Plain Cement concrete type C-1, 1:3:6 (using 20 mm graded stone aggregate) as in foundations, filling and mass concrete complete all as specified and directed. |
| 4 | M&L for damp proof course 40mm thkM-20 (Nominal Mix) using 12.5mm graded crushed stone aggregate with water proofing compound conforming to IS-2645 liquid grade as per manufacturer’s instructions with and including polythene film 200 micron over and including 85/25 grade Industrial bitumen (IS-702 : 1988) @ 1.5 kg/sqm blended with the dry sand @ 0.05 cubic meter/ sqm. complete all as specified and directed. |
| 5 | M&L for 75 mm thick cement concrete M10 (Nominal Mix) with 40mm graded crushed aggregate finished even and fair laid to a slope of 1 in 12, laid in alternate bays, each bay not exceeding 3 m length with joint filled with bituminous mastic filling comprising a mixture of 1 part of heated Industrial bitumen 85/25 grade and two parts of heated sand as in plinth protection Complete all as specified and directed. |
| 6 | M&L for forming fair finished drain or channel 30 cm inner girth in cement concrete, using extra cement, including forms, moulds, mi- tred/stopped ends etc Complete all as specified and directed. |
| 7 | M & L for Sand filling under floors or in foundation including watering and consolidation complete all as specified. |
| 8 | Dismantling of plain or corrugated steel sheeting, any gauge, thickness, flat or curved incl ridges hips valleys as in roof coverings complete all as specified and directed. |
| 9 | M & L for pre-painted hot-dip aluminium-zinc alloy metallic coated of any profile steel sheet corresponding to IS 15965:2012 of durability class 3, atmospheric classification category 3, coating class AZ150, 0.50 mm thick, of an approved colour and having yield strength of 550 MPa as in roof covering fixed with self tapping screws as specified up to anyheight including all necessary scaffolding and safety measures complete all as specified and directed. |
| 10 | M & L for pre-painted hot-dip aluminium-zinc alloy metallic coated plain steel sheet as per IS 15965:2012 of durability class 3, atmospheric classification category 3, coating class AZ150, 0.50 mm thick, of an approved colour and having yield strength of 550 MPa as in ridge/ valley/ gutter fixed with self tapping screws as specified any height Mtr height including all necessary scaffolding and safety measures complete all as specified and directed. |
| 11 | Demolition of brick work built in CM including all quions, arches, pillars etc, but excluding ashlar facings, dressed stonework and precast concrete articles including removal of the rubbish off the premises all as specified and directed. |
| 12 | M&L Brick work with flyash old size bricks, straight or curved on plan exc. 6m mean radius built in cement mortar 1:6 complete all as directed. |
| 13 | M & L for rendering 20mm thick in CM (1:4) in two layers (8mm thick in CM (1:4) with approved water proofing compound as per manufacturing instraction over backing coat of 12mm thick in CM (1:4)) on brick work or concrete surfaces finished fair & even. Complete all as specified and directed. (Note:- WPC will be measured and paid separately) |
| 14 | Supply only Integral Water proofing compound Complete all as specified and directed. |
| 15 | Material & Labour for preparation of new surfaces of plastered walls and applying Two coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm ) over plastered surfaces of walls to prepare the surface even and smooth Complete all as specified and directed. |
| 16 | M&L for rendering 15 mm thick in CM 1:6 on fair faces of brick work surfaces finished fair and even complete all as specified. |
| 17 | Material & Labour for preparation of new surfaces of plastered walls and applying Two coats of Distempering with 1st quality acrylic distemper (ready mixed) having VOC content less than 50 gms/litre, of approved manufacturer, of required shade and colour complete, as per manufacturer's specification. over and including a coat of primer and 1.0 mm thick white wall care putty (premium quality) over plastered surfaces of walls to prepare the surface even and smooth Complete all as specified and directed. |
| 18 | Dismantling wrought iron or mild steel work of any description not otherwise provided complete all as specified and as directed. |
| 19 | S & F Roof trusses (framed) of angle iron members trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats etc. |
| 20 | S&F for framed work such as grills, gratings, etc.. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe.290.Gde-E-165 , the grill shall be inserted in the wall surface including necessary drilling and grouting with cement etc |
| 21 | SS & F for Hand rails, half round or other steel section or core for wooden hand-rail straight portion, drilled and countersunk for balusters running bars, for doors, balusters, nosing to steps including embeding in concrete and screwing etc. wind ties for roof including securing bolts complete all as spd and directed. |
| 22 | M&L for preparation of old painted of steel surfaces of any description not otherwise described over 10 cm width or girth and applying one coat of synthetic enamel paint complete all as specified and directed. |
| 23 | M&L for preparing of new steel & iron surfaces of any description, not otherwise described, over 10cm width or girth and applying two coats of synthetic enameled paint over a coat of Red oxide zinc chrome primer zinc chrome complete all as specified and as directed. |
| 24 | M&L for two coats of synthetic enamel paint on new surface over one coat of red oxide primer including preparation of surface of any description, n.exc 10 cm in width or girth not other wise described all as specified and directed by Engr-in-Charge. |
| 25 | Dismantling fencing wire mesh any type complete all as apecified and directed by Engineer- in -Charge |
| 26 | Supply and fix Galvanised iron wire using Hot Dip technology chain electrogalvanised coating chain link fencing wire mesh of size 75mmx75mm minimum dia meter of wire 3 mm confirming to IS -2712-2003 havinga tensile strength 400 to 500 Mpa including line wires, (Line wires will be measured and paid separately under supply only item) , straining bolts, etc. including provission of binding wireThe mesh wire a of the fabric shall be manufactured from ISI marked (make= Tata wireson) galvanised steel confirming to IS - 280:2006 (4th revision).The Kuncled ends should be of at least 50% of the sixe of the square mesh. The wires used in fencing should be long lasting and resistance to corrosion and testing criteria fullfill the requirement as per IS 1161:1998 complete all as specified and directed. |
| 27 | S& F in repairs Stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples complete. |
| 28 | Demolition of reinforced cement concrete in ground floors and pavings n.exc 15 cm thickness (below or above ground level) and removal of the rubbish off the premises all as specified and directed. |
| 29 | M&L for Steel Centering and shuttering including strutting, propping etc. and removal of form to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams; and similar work; vertical or to batter |
| 30 | M & L for reinforced cement concrete (Design Mix) M-25 (20mm graded stone aggregate) foundations, including rafts, footings, foundation beams, plinth beams; bases for columns, etc. and mass concrete etc complete all as directed. |
| 31 | M & L for Mild steel TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips. |
| 32 | M&L TMT mild steel bars 6mm to 8mm dia ,cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with mild steel wire (annealed) not less than 0.9mmdia or securing with clips quality conforming to complete all as specified. |
| 33 | Taking down chowkats or frames with shutter w/o taking off shutter from the frame exc 1.5 Sqm & n. exe 4 Sqm each incl cutting holes for taking out hold fast or dismantling brick work (holes cut and any other damage to jambs, walls for taking out hold fast shall be finished identical to existing finish without any extra cost to Govt.) all as specified and directed By Engr-in-charge. |
| 34 | Powder coated aluminium (minimum thickness of powder coating 50 micron) work for doors, windows, ventilators and partitions (Fixed portions) with extruded built up standard tubular sections/ appropriate Zsections and other sections of approved make conforming to IS: 733 and IS:1285, fixing with dashfasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top,bottom and sides with required EPDM rubber/ neoprene gasketetc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including Aluminium snap beading for glazing/ paneling, all complete as per architectural drawings and the directions of Engineer-in-Charge. |
| 35 | S & F powder coated Anodised aluminium window shutters, sliding type without sash bars, (minimum thickness of powder coating 50 micron) for three track shutters of windows & ventilators aluminium sections weighing 0.55 kg/m including necessary joining cleats , Aluminium snap beading for glazing/ paneling, C.P. brass/ stainless steel screws, anodised aluminium fittings suitaible etc all complete as per architectural drawings and the directions of Engineer-in-charge. |
| 36 | S&F in repair PVC SWR pipes, 150 mm bore single socketed in any length with rubber ring joint fixed to wall with steel clamps for rain water pipes all as specified and directed . Make : Supreme/ Finolex. |
| 37 | S&F in repair 150mm bore PVC (SWR) bends any radius with access door complete all as specified and as directed by EIC. Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Sep 26, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedOct 16, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 12 daysOct 17, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 13 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender