Tender For Renovation And Maintenance Work At The Estate Managers Office, U.P. Housing And Development Board, D-2, Talpura Scheme, Jhansi.
Tender Value
80.25 Lakhs
Estimated cost
Bid Submission
17 Oct 2026
15 days left
EMD
1.61 Lakhs
Bank guarantee accepted
Document Fee
3540
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Jalaun → Uttar Pradesh
EMD Exemption
Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for Renovation And Maintenance Work At The Estate Managers Office, U.P. Housing And Development Board, D-2, Talpura Scheme, Jhansi.
BOQ
| Sl. No. | Item Description |
| 1 | Boring, Providing And Installing Cast In Situ Single Under Reamed Piles Ofspecified Diameter And Length Below Pile Cap In M-25 Cement Concrete, Tocarry A Safe Working Load Not Less Than Specified, Excluding The Cost Of Steel Reinforcement But Including The Cost Of Boring With Bentonite Solution And The Length Of The Pile To Embedded In Pile Cap Etc. All Complete. (Length Of Pile For Payment Shall Be Measured Upto To The Bottom Of Pile Cap) :300 Mm Dia Piles Dsr 20.3.1 |
| 2 | Earth Work In Excavation By Mechanical Means (Hydraulic Excavator)/ Manual Means Over Areas (Exceeding 30 Cm In Depth, 1.5 M In Width As Well As 10 Sqm On Plan) Including Getting Out And Disposal Of Excavated Earth Lead Upto 50 M And Lift Upto 1.5 M, As Directed By Engineer-InCharge. 2.6.1 All Kinds Of Soil Dsr 2.6.1 |
| 3 | Excavating, Supplying And Filling Of Local Earth (Including Royalty) By Mechanical Transport Upto A Lead Of 5Km Also Including Ramming And Watering Of The Earth In Layers Not Exceeding 20 Cm In Trenches, Plinth, Sides Of Foundation Etc. Complete. Dsr 2.25A |
| 4 | Providing And Laying In Position Cement Concrete Of Specified Grade Excluding The Cost Of Centering And Shuttering - All Work Up To Plinth Level : 1:4:8 (1 Cement : 4 Coarse Sand (Zone-Iii) Derived From Natural Sources : 8 Graded Stone Aggregate 40 Mm Nominal Size Derived From Natural Sources) Dsr 4.1.8 |
| 5 | Supplying And Filling In Plinth With Sand Under Floors, Including Watering, Ramming, Consolidating And Dressing Complete. Dsr 2.27 |
| 6 | Treatment Of Soil Under Existing Floors Using Chemical Emulsion @ One Litre Per Hole, 300 Mm Apart Including Drilling 12 Mm Diameter Holes And Plugging With Cement Mortar 1 :2 (1 Cement : 2 Coarse Sand) To Match The Existing Floor: With Chlorpyriphos/Lindane E.C. 20% With 1% Concentration. Dsr 2.35.3.1 |
| 7 | Providing And Laying In Position Specified Grade Of Reinforced Cement Concrete, Excluding The Cost Of Centering, Shuttering, Finishing And Reinforcement - All Work Up To Plinth Level1:1.5:3 (1 Cement : 1.5 Coarse Sand (Zone-Lll) Derived From Natural Sources : 3 Graded Stone Aggregate 20 Mm Nominal Size Derived From Natural Sources) Dsr 5.1.2 |
| 8 | Reinforced Cement Concrete Work In Beams, Suspended Floors, Roofs Having Slope Up To 15° Landings, Balconies, Shelves, Chajjas, Lintels, Bands, Plain Window Sills, Staircases And Spiral Stair Cases Above Plinth Level Up To Floor Five Level, Excluding The Cost Of Centering, Shuttering, Finishing And Reinforcement With 1:1.5:3 (1 Cement : 1.5 Coarse Sand(Zone-Ill) Derived From Natural Sources : 3 Graded Stone Aggregate 20 Mm Nominal Size Derived From Natural Sources). Dsr 5.3 |
| 9 | Reinforced Cement Concrete Work In Beams, Suspended Floors, Roofs Having Slope Up To 15° Landings, Balconies, Shelves, Chajjas, Lintels, Bands, Plain Window Sills, Staircases And Spiral Stair Cases Above Plinth Level Up To Floor Five Level, Excluding The Cost Of Centering, Shuttering, Finishing And Reinforcement With 1:1.5:3 (1 Cement : 1.5 Coarse Sand(Zone-Ill) Derived From Natural Sources : 3 Graded Stone Aggregate 20 Mm Nominal Size Derived From Natural Sources). Dsr 5.3 |
| 10 | Brick Work With Common Burnt Clay F.P.S. (Non Modular) Bricks Of Class Designation 15 In Foundation And Plinth In:Cement Mortar 1:6 (1 Cement : 4 Coarse Sand) Dsr 6.1.2 |
| 11 | Steel Reinforcement For R.C.C. Work Including Straightening, Cutting, Bending, Placing In Position And Binding All Complete Upto Plinth Level.. Thermo-Mechanically Treated Bars Of Grade Fe-500D OrMore. Dsr 5.22.6 |
| 12 | 15 Mm Cement Plaster On Rough Side Of Single Or Half Brick Wall Of Mix: 1:4 (1 Cement : 4 Coarse Sand) Dsr 13.5.1 |
| 13 | Brick Work With Common Burnt Clay F.P.S. (Non Modular) Bricks Of Class Designation 15 In Super Structure Above Plinth Level Up To Floor V Level In All Shapes And Size In:1:4 (1 Cement : 4 Sand) Dsr 6.4.1 |
| 14 | Brick Work With Common Burnt Clay F.P.S. (Non Modular) Bricks Of Class Designation 15 In Super Structure Above Plinth Level Up To Floor V Level In All Shapes And Size In:1:6 (1 Cement : 6 Sand) Dsr 6.4.2 |
| 15 | Half Brick Masonary With Common Burnt Clay F.P.S (Non Modular) Brick Of Class Designation 15 In Super Structure Above Plinth Level Up To Floor V Level Cement Mortar 1:4 (1 Cement : 4 Coarse Sand) Dsr 6.13.2 |
| 16 | 12 Mm Cement Plaster : 1:6 (1 Cement : 6 Coarse Sand) Dsr 13.4.2 |
| 17 | 15 Mm Cement Plaster On Rough Side Of Single Or Half Brick Wall Of Mix: 1:6 (1 Cement : 6 Coarse Sand) Dsr 13.5.2 |
| 18 | Add for plaster drip course/ groove in plastered surface or moulding to R.C.C. projections.Dsr 5.30 |
| 19 | Cement Concrete Flooring 1:2:4 (1 Cement : 2 Coarse Sand : 4 Graded Stone Aggregate) Finished With A Floating Coat Of Neat Cement, Including Cement Slurry, But Excluding The Cost Of Nosing Of Steps Etc. Complete.25 Mm Thick With 20 Mm Nominal Size Stone Aggregate. Dsr 11.3/40*2 |
| 20 | Cement Concrete Flooring 1:2:4 (1 Cement : 2 Coarse Sand : 4 Graded Stone Aggregate) Finished With A Floating Coat Of Neat Cement, Including Cement Slurry, But Excluding The Cost Of Nosing Of Steps Etc. Complete. 40 Mm Thick With 20 Mm Nominal Size Stone Aggregate. 40 Mm Thick With 20 Mm Nominal Size Stone Aggregate. Dsr 11.3.1 |
| 21 | Cement Plaster Skirting Up To 30 Cm Height, With Cement Mortar 1:3 (1 Cement : 3 Coarse Sand), Finished With A Floating Coat Of Neat Cement. 18 Mm Thick. Dsr 11.6.1 |
| 22 | Providing And Fixing 18 Mm Thick Gang Saw Cut Mirror Polished Premoulded And Prepolished, Machine Cut For Kitchen Platforms, Vanity Counters, Window Sills, Facias And Similar Locations Of Required Size, Approved Shade, Colour And Texture Laid Over 20 Mm Thick Base Cement Mortar 1:4 (1 Cement : 4 Coarse Sand), Joints Treated With White Cement, Mixed With Matching Pigment, Epoxy Touch Ups, Including Rubbing, Curing, Moulding And Polishing Of Edges To Give High Gloss Finish Etc. Complete At All Levels.Granite Stone Slab Of Colour Black, Cherry/Ruby Red. Area Of Slab Up To 0.50Sqm. Dsr 8.2.2.2 |
| 23 | Providing And Laying Ceramic Glazed Floor Tiles Of Size 300X300 Mm (Thickness To Be Specified By The Manufacturer) Of 1St Quality Conforming To Is : 15622 Of Approved Make In Colours Such As White, Ivory, Grey, Fume Red Brown, Laid On 20 Mm Thick Cement Mortar 1:4 (1 Cement : 4 Coarse Sand), Jointing With Grey Cement Slurry @ 3.3 Kg/Sqm Including Pointing The Joints With White Cement And Matching Pigment Etc., Complete. Dsr 11.37 |
| 24 | Providing And Fixing Ist Quality Ceramic Glazed Wall Tiles Conforming To Is: 15622 (Thickness To Be Specified By The Manufacturer), Of Approved Make, In All Colours, Shades Except Burgundy, Bottle Green, Black Of Any Size As Approved By Engineer-In-Charge, In Skirting, Risers Of Steps And Dados, Over 12 Mm Thick Bed Of Cement Mortar 1:3 (1 Cement : 3 Coarse Sand) And Jointing With Grey Cement Slurry @ 3.3Kg Per Sqm, Including Pointing In White Cement Mixed With Pigment Of Matching Shade Complete. Dsr 8.31 |
| 25 | - Providing And Fixing Isi Marked Flush Door Shutters Conforming To Is : 2202 (Part I) Non-Decorative Type, Core Of Block Board Construction With Frame Of 1St Class Hard Wood And Well Matched Commercial 3 Ply Veneering With Vertical Grains Or Cross Bands And Face Veneers On Both Faces Of Shutters: 35 Mm Thick Including Isi Marked Stainless Steel Butt Hinges With Necessary Screws Dsr 9.21.1 |
| 26 | Providing And Fixing Isi Marked Flush Door Shutters Conforming To Is : 2202 (Part I) Decorative Type, Core Of Block Board Construction With Frame Of 1St Class Hard Wood And Well Matched Teak 3 Ply Veneering With Vertical Grains Or Cross Bands And Face Veneers On Both Faces Of Shutters. 35 Mm Thick Including Isi Marked Stainless Steel Butt Hinges With Necessary Screws. Dsr 9.20.1 |
| 27 | Providing And Fixing Factory Made Single Extruded Wpc (Wood Polymer Composite) Solid Plain Flush Door Shutter Of Required Size Comprising Of Virgin Polymer Of K Value 58-60 (Suspension Grade), Calcium Carbonate And Natural Fibers (Wood Powder/ Rice Husk/Wheat Husk) And Non Toxic Additives (Maximum Toxicity Index Of 12 For 100 Gms) Having Minimum Density Of 850 Kg/Cum And Screw Withdrawal Strength Of 1800 N (Face) & 900 N (Edge), Minimum Compressive Strength 50 N/Mm2, Modulus Of Elasticity 850 N/Mm2 And Resistance To Spread Of Flame Of Class A Category With Property Of Being Termite/Borer Proof, Water/Moisture Proof And Fire Retardant And Fixing With Stainless Steel Butt Hinges Of Required Size With Necessary Full Body Threaded Star Headed Counter Sunk S§.S Screws, All As Per Direction Of Engineer-In- Charge. (Note: Stainless Steel Butt Hinges And Necessary S.S Screws Shall Be Paid Separately). Dsr 26.87.1 |
| 28 | Providing And Fixing Factory Made Single Extruded Wpc (Wood Polymer Composite) Solid Door/Window/Clerestory Windows & Other Frames/ Chowkhat Comprising Of Virgin Pvc Polymer Of K Value 58-60 (Suspension Grade), Calcium Carbonate And Natural Fibers (Wood Powder/ Rice Husk/ Wheat Husk) And Non Toxic Additives (Maximum Toxicity Index Of 12 For 100 Gms) Fabricated With Miter Joints After Applying Pvc Solvent Cement And Screwed With Full Body Threaded Star Headed Ss Screws Having Minimum Frame Density Of 750 Kg/Cum, Screw Withdrawal Strength Of 2200 N (Face) & 1100 N (Edge), Minimum Compressive Strength Of 58 N/Mm2, Modulus Of Elasticity 900 N/Mm2 And Resistance To Spread Of Flame Of Class A Category With Property Of Being Termite/Borer Proof, Water/Moisture Proof And Fire Retardant And Fixed In Position With M.S Hold Fast/Lugs/Ss Dash Fasteners Of Required Dia And Length Complete As Per Direction Of Engineer-In- Charge. (M.S Hold Fast/Lugs Or Ss Dash Fasteners Shall Beframe Size 45 X 70 Mm Paid For Separately). Note: For Wpc Solid Door/Fwindow Frames, Minus 5 Mm Tolerance In Dimensions I.E Depth And Width Of Profile Shall Be Acceptable. Variation In Profile Dimensions On Plus Side Shall Be Acceptable But No Extra Payment On This Account Shall Be Made. Dsr 26.86.1 |
| 29 | Providing And Fixing Angle Iron Frames For Doors, Windows And Ventilators Of Mild Steel Angle Sections Of Size 35X35X5 Mm, Joints Mitred And Welded By Angle Iron 35X35X5 Mm Or 35X 5 Mm Flat Pieces To The Existing T-Iron Frame Or To The Wall With Dash Fastener, Including Fixing Of Necessary Butt Hinges And Screws And Applying A Priming Coat Of Approved Steel Primer, All Complete As Per The Direction Of Engineer-In-Charge. Hold Fast Dsr 10.31 |
| 30 | Providing And Fixing M.S. Grills Of Required Pattern In Frames Of Windows Etc. With M.S. Flats, Square Or Round Bars Etc. Including Priming Coat With Approved Steel Primer All Complete. Fixed To Steel Windows By Welding. Fabrication Of M.S. Grill Dsr 9.48.1 |
| 31 | Providing And Fixing Factory Made Isi Marked Steel T Section 40X40X6 Mm , Windows And Ventilators, Side /Top /Centre Hung, With Beading And All Members Such As F7D, F4B, K11 B And K12 B Etc. Complete Of Standard Rolled Steel Sections, Joints Mitred And Flash Butt Welded And Sash Bars Tenoned And Riveted, Including Providing And Fixing Of Hinges, Pivots, Including Priming Coat Of Approved Steel Primer, But Excluding The Cost Of Other Fittings, Complete All As Per Approved Design, (Sectional Weight Of Only Steel Members Shall Be Measured For Payment). Fixing With 15X3 Mm Lugs 10 Cm Long Embedded In Cement Concrete Block 15X10X10 Cm Of C.C. 1:3:6 (1 Cement : 3 Coarse Sand : 6 Graded Stone Aggregate 20 Mm Nominal Size). Fabrication Of Hold Fast For Door Chaukhats And Windows. Dsr 10.11.1 |
| 32 | Providing And Fixing Angle Iron Frames For Doors, Windows And Ventilators Of Mild Steel Angle Sections Of Size 35X35X5 Mm, Joints Mitred And Welded By Angle Iron 35X35X5 Mm Or 35X 5 Mm Flat Pieces To The Existing T-Iron Frame Or To The Wall With Dash Fastener, Including Fixing Of Necessary Butt Hinges And Screws And Applying A Priming Coat Of Approved Steel Primer, All Complete As Per The Direction Of Engineer-In-Charge. Providing And Fixing Angle Iron Frames For Doors, Windows And Ventilators Of Mild Steel Angle Sections Dsr 10.31 |
| 33 | Painting Wood Work With Deluxe Multi Surface Paint Of Required Shade. Two Or More Coat Applied @ 0.90 Itr/10 Sqm Over An Under Coat Of Primer Applied @0.75 Itr/10 Sqm Of Approved Brand And Manufacture Dsr 13.48.2 |
| 34 | Distempering With 1St Quality Acrylic Distemper (Ready Mixed) Having Voc Content Less Than 50 Gms/Litre, Of Approved Manufacturer, Of Required Shade And Colour Complete, As Per Manufacturer'S Specification. New Work (Two Or More Coats) Over And Including Water Thinnable Priming Coat With Cement Primer Having Voc Content Less Than 50 Gram/Litre Dsr 13.41.1 |
| 35 | Finishing Walls With Premium Acrylic Smooth Exterior Paint With Silicone Additives Of Required Shade : New Work (Two Or More Coats Applied @ 1.43 Ltr/ 10 Sqm Over And Including Priming Coat Of Exterior Primer Applied @ 2.20 Kg/ 10 Sqm). Dsr 13.47.1 |
| 36 | Painting With Synthetic Enamel Paint Of Approved Brand And Manufacture Of Required Colour To Give An Even Shade :Two Or More Coats On New Work Over An Under Coat Of Suitable Shade With Ordinary Paint Of Approved Brand And Manufacture. Dsr 13.62.1 |
| 37 | Finishing Walls With Water Proofing Cement Paint Of Required Shade :New Work (Two Or More Coats Applied @ 3.84 Kg/10 Sqm). Dsr 13.44.1 |
| 38 | Providing And Applying White Cement Based Putty Of Average Thickness 1 Mm, Of Approved Brand And Manufacturer, Over The Plastered Wall Surface To Prepare The Surface Even And Smooth Complete. Dsr 13.8 |
| 39 | Providing And Fixing Bright Finished Brass Hanging Type Floor Door Stopper With Necessary Screws, Etc. Complete. 150Mm. Dsr 9.82 |
| 40 | Providing And Fixing Aluminium Sliding Door Bolts, Isi Marked Anodised (Anodic Coating Not Less Than Grade Ac 10 As Per Is : 1868), Transparent Or Dyed To Required Colour Or Shade, With Nuts And Screws Etc. Complete : 250X16 Mm Dsr 9.96.2 |
| 41 | Providing And Fixing Aluminium Tower Bolts, Isi Marked, Anodised (Anodic Coating Not Less Than Grade Ac 10 As Per Is : 1868 ) Transparent Or Dyed To Required Colour Or Shade, With Necessary Screws Etc. Complete : 250X10Mm. Dsr 9.97.2 |
| 42 | Providing And Fixing Aluminium Tower Bolts, Isi Marked, Anodised (Anodic Coating Not Less Than Grade Ac 10 As Per Is : 1868 ) Transparent Or Dyed To Required Colour Or Shade, With Necessary Screws Etc. Complete : 200X10Mm. Dsr 9.97.3 |
| 43 | Providing And Fixing Aluminium Handles, Isi Marked, Anodised (Anodic Coating Not Less Than Grade Ac 10 As Per Is : 1868) Transparent Or Dyed To Required Colour Or Shade, With Necessary Screws Etc. Complete Dsr 9.100.1 |
| 44 | Providing and laying integral cement based water proofing treatment including preparation of surface as required for treatment of roofs, balconies, terraces etc consisting of following operations: (a) Applying a slurry coat of neat cement using 2.75 kg/sqm of cement admixed with water proofing compound conforming to IS. 2645 and approved by Engineer-in-charge over the RCC slab including adjoining walls upto 300 mm height including cleaning the surface before treatment. (b) Laying brick bats with mortar using broken bricks/brick bats 25 mm to 115 mm size with 50% of cement mortar 1:5 (1 cement : 5 coarse sand) admixed with water proofing compound conforming to IS : 2645 and approved by Engineer-in-charge over 20 mm thick layer of cement mortar of mix 1:5 (1 cement :5 coarse sand ) admixed with water proofing compound conforming to IS : 2645 and approved by Engineer-in-charge to required slope and treating similarly the adjoining walls upto 300 mm height including rounding of junctions of walls and slabs. (c) After two days of proper curing applying a second coat of cement slurry using 2.75 kg/ sqm of cement admixed with water proofing compound conforming to IS : 2645 and approved by Engineer-in-charge. (d) Finishing the surface with 20 mm thick jointless cement mortar of mix 1:4 (1 cement :4 coarse sand) admixed with water proofing compound conforming to IS : 2645 and approved by Engineer-in-charge including laying glass fibre cloth of approved quality in top layer of plaster and finally finishing the surface with trowel with neat cement slurry and making pattern of 300x300 mm square 3 mm deep.(e) The whole terrace so finished shall be flooded with water for a minimum period of two weeks for curing and for final test.“All above operations to be done in order and as directed and specified by the Engineer-in-Charge : With average thickness of 120 mm and minimum thickness at khurra as 65 mm. Dsr 22.7.1 |
| 45 | Painting Steel Work With Deluxe Multi Surface Paint To Give An Even Shade. Two Or More Coat Applied @ 0.90 Ltr/ 10 Sqm Over An Under Coat Of Primer Applied @ 0.80 Ltr/ 10 Sqm Of Approved Brand And Manufacture Dsr 13.48.3 |
| 46 | Providing & Fixing Glass Panes With Putty And Glazing Clips In Steel Doors, Windows, Clerestory Windows, All Complete With :4.0 Mm Thick Glass Panes Dsr 10.30.1 |
| 47 | Providing And Fixing Glass Strips In Joints Of Terrazo/ Cement Concrete Floors. 40 Mm Wide And 4 Mm Thick. Dsr 11.13.1 |
| 48 | Providing & Laying Of Light Cinder Filling Under Floor Of Toilets & Other Sunken Roofs. MR |
| 49 | Providing And Laying Water Proofing Treatment In Sunken Portion Of Wcs, Bathroom Etc., By Applying Cement Slurry Mixed With Water Proofing Cement Compound Consisting Of Applying (A) First Layer Of Slurry Of Cement @ 0.488 Kg/Sqm Mixed WithWater Proofing Cement Compound @ 0.253 Kg/ Sqm. This Layer Will Be Allowed To Air Cure For 4 Hours (B) Second Layer Of Slurry Of Cement @ 0.242 Kg/Sqm Mixed With Water Proofing Cement Compound @ 0.126 Kg/Sqm. This Layer Will Be Allowed To Air Cure For 4 Hours Followed With Water Curing For 48 Hours.The Rate Includes Preparation Of Surface, Treatment And Sealing Of All Joints, Corners, Junctions Of Pipes And Masonry With Polymer Mixed Slurry. Dsr 22.5 |
| 50 | Centering And Shuttering Including Strutting, Propping Etc. And Removal Of Form For : Suspended Floors, Roofs, Landings, Balconies And Access Platform Dsr 5.9.3 |
| 51 | Centering And Shuttering Including Strutting, Propping Etc. And Removal Of Form For : Lintels, Beams, Plinth Beams, Girders, Bressumers And Cantilevers Dsr 5.9.5 |
| 52 | Demolishing Brick Work Manually/ By Mechanical Means Including Stacking Of Serviceable Material And Disposal Of Unserviceable Material Within 50 Metres Lead As Per Direction Of Engineer-In-Charge.In Cement Mortar Dsr 15.7.4 |
| 53 | Disposal Of Building Rubbish / Malba / Similar Unserviceable, Dismantled Or Waste Materials By Mechanical Means, Including Loading, Transporting, Unloading To Approved Municipal Dumping Ground Or As Approved By Engineer-In-Charge, Beyond 50 M Initial Lead, For All Leads Including All Lifts Involved. Dsr 15.6 |
| 54 | Providing And Fixing Isi Marked Oxidised M.S. Sliding Door Bolts With Nuts And Screws Etc. Complete (Copper Oxidised As Per Is 1378). 250X16 Mm. Dsr 9.62.2 |
| 55 | Providing And Fixing Isi Marked Oxidised M.S. Tower Bolt Black Finish, (Barrel Type) With Necessary Screws Etc. Complete (Copper Oxidised As Per Is 1378).250X10 Mm. Dsr 9.63.1 |
| 56 | Providing And Fixing Isi Marked Oxidised M.S. Handles Conforming To Is:4992 With Necessary Screws Etc. Complete (Copper Oxidised As Per Is 1378). 125 Mm. Dsr 9.66.1 |
| 57 | Providing And Fixing Water Closet Squatting Pan (Indian Type W.C. Pan ) With 100 Mm Sand Cast Iron P Or S Trap, 10 Litre Low Level White P.V.C. Flushing Cistern, Including Flush Pipe, With Manually Controlled Device (Handle Lever) Conforming To Is : 7231, With All Fittings And Fixtures Complete, Including Cutting And Making Good The Walls And Floors Wherever Required:White Vitreous China Orissa Pattern W.C. Pan Of Size 580X440 Mm With Integral Type Foot Rests. Dsr 17.1.1 |
| 58 | Providing And Fixing White Vitreous China Pedestal Type Water Closet ( European Type W.C. Pan ) With Seat And Lid, 10 Litre Low Level White P.V.C. Flushing Cistern, Including Flush Pipe, With Manually Controlled Device (Handle Lever) Conforming To Is : 7231, With All Fittings And Fixtures Complete, Including Cutting And Making Good The Walls And Floors Wherever Required:W.C. Pan With Isi Marked White Solid Plastic Seat And Lid. Dsr. 17.2.1 |
| 59 | Providing And Fixing Wash Basin With C.I. Brackets, 15 Mm C.P. Brass Pillar Taps, 32 Mm C.P. Brass Waste Of Standard Pattern, Including Painting Of Fittings And Brackets, Cutting And Making Good The Walls Wherever Require. A) White Vitreous China Flat Back Wash Basin Size 550X 400 Mm With Single 15 Mm C.P. Brass Pillar Tappillar Tap. Dsr 17.7.4 |
| 60 | Providing & fixing white vitreous china wash basin with C.I. brackets painted white, 15 mm C.P. brass pillar taps, C.P. brass chain with rubber plug, 32mm C.P. brass waste of standerd pattern including cutting & making good the walls wherever required.White Vitreous China Wash basin size 630x450 mm with a pair of 15 mm C.P. brass pillar taps. Dsr 17.7.1 |
| 61 | Providing And Fixing Flexible P.V.C. Waste Pipe For Sink Or Wash Basin Including Pvc Waste Fittings Complete.Felxible Pipe. 32Mm Dia. Dsr 17.28.1 |
| 62 | Providing and fixing P.V.C. waste pipe for sink or wash basin including P.V.C. waste fittings complete. Semi rigid pipe. 32 mm dia. Dsr 17.28.1.1 |
| 63 | Providing And Fixing Flexible P.V.C. Waste Pipe For Sink Or Wash Basin Including Pvc Waste Fittings Complete.Felxible Pipe. 40Mm Dia. Dsr 17.28.2.2 |
| 64 | Providing And Fixing 600X450 Mm Beveled Edge Mirror Of Superior Glass (Of Approved Quality) Complete With 6 Mm Thick Hard Board Ground Fixed To Wooden Cleats With C.P. Brass Screws And Washers Complete. Dsr 17.31 |
| 65 | Providing and fixing Stainless Steel AISI 304 (18/8) kitchen sink as per I.S. 13983 with C.I. brackets and stainless steel plug 40 mm including painting of fittings and brackets, cutting and making good the walls wherever required : Kitchen sink with drain board, 510x1040 mm bowl depth 250 mm. |
| 66 | Providing and fixing PTMT Bottle Trap for Wash basin and sink Bottle trap 38 mm single piece moulded with height of 270 mm, effective length of tail pipe 260 mm from the centre of the waste coupling, 77 mm breadth with 25 mm minimum water seal, weighing not less than 263 gms. |
| 67 | Providing And Fixing On Wall Face Unplasticised Rigid Pvc Rain Water Pipes Conforming To Is : 13592 Type A, Including Jointing With Seal Ring Conforming To Is : 5382, Leaving 10 Mm Gap For Thermal Expansion, (I) Single Socketed Pipes. 110 Mm Diameter. Dsr 12.41.2 |
| 68 | Providing And Fixing On Wall Face Unplasticised - Pvc Moulded Fittings/ Accessories For Unplasticised Rigid Pvc Rain Water Pipes Conforming To Is : 13592 Type A, Including Jointing With Seal Ring Conforming To Is : 5382, Leaving 10 Mm Gap For Thermal Expansion. Coupler 110 Mm. Dsr 12.42.1 |
| 69 | Providing And Fixing On Wall Face Unplasticised - Pvc Moulded Fittings/ Accessories For Unplasticised Rigid Pvc Rain Water Pipes Conforming To Is : 13592 Type A, Including Jointing With Seal Ring Conforming To Is : 5382, Leaving 10 Mm Gap For Thermal Expansion. Tee 110 Mm. Dsr 12.42.3 |
| 70 | Providing And Fixing On Wall Face Unplasticised - Pvc Moulded Fittings/ Accessories For Unplasticised Rigid Pvc Rain Water Pipes Conforming To Is : 13592 Type A, Including Jointing With Seal Ring Conforming To Is : 5382, Leaving 10 Mm Gap For Thermal Expansion. Bend 110 Mm. Dsr 12.41.5.2 |
| 71 | Providing And Fixing Unplasticised -Pvc Pipe Clips Of Approved Design To Unplasticised - Pvc Rain Water Pipes By Means Of 50X50X50 Mm Hard Wood Plugs, Screwed With M.S. Screws Of Required Length, Including Cutting Brick Work And Fixing In Cement Mortar 1:4 (1 Cement : 4 Coarse Sand) And Making Good The Wall Etc. Complete. 110 Mm. Dsr 12.43.2 |
| 72 | Making Khurras 45X45 Cm With Average Minimum Thickness Of 5 Cm Cement Concrete 1:2:4 (1 Cement : 2 Coarse Sand : 4 Graded Stone Aggregate Of 20 Mm Nominal Size) Over Pvc Sheet 1M X 1 M X 400 Micron, Finished With 12 Mm Cement Plaster 1:3 (1 Cement : 3 Coarse Sand) And A Coat Of Neat Cement,Punning,Rounding The Edges And Making And Finishing The Outlet Complete. 110Mm. Dsr 12.22 |
| 73 | Providing And Fixing 100 Mm Diameter And 60 Cm Long Rain Water Spout In Cement Mortar 1:4 (1 Cement : 4 Fine Sand). Dsr 12.37.1 |
| 74 | Providing And Fixing Chlorinated Polyvinyl Chloride (Cpvc) Pipes, Having Thermal Stability For Hot & Cold Water Supply Including All Cpvc Plain & Brass Threaded Fittings Including Fixing The Pipe With Clamps At 1.00M Spacing. This Includes Jointing Of Pipes & Fittings With One Step Cpvc Solvent Cement And Testing Of Joints Complete As Per Direction Of Engineer In Charge. Internal Work-Exposed On Wall. 20Mm Dia Nominal Outer Dia Pipes. Dsr 18.7.2 |
| 75 | Providing And Fixing Chlorinated Polyvinyl Chloride (Cpvc) Pipes, Having Thermal Stability For Hot & Cold Water Supply Including All Cpvc Plain & Brass Threaded Fittings Including Fixing The Pipe With Clamps At 1.00M Spacing. This Includes Jointing Of Pipes & Fittings With One Step Cpvc Solvent Cement And Testing Of Joints Complete As Per Direction Of Engineer In Charge. Internal Work-Exposed On Wall. 25Mm Dia Nominal Outer Dia Pipes Dsr 18.7.3 |
| 76 | Providing And Fixing Chlorinated Polyvinyl Chloride (Cpvc) Pipes, Having Thermal Stability For Hot & Cold Water Supply Including All Cpvc Plain & Brass Threaded Fittings I/C Fixing The Pipe With Clamps At 1.00M Spacing. This Includes Jointing Of Pipes & Fittings With One Step Cpvc Solvent Cement And The Cost Of Cutting Chases And Making Good The Same Including Testiang Of Joints Complete As Per Direction Of Engineer In Charge. Concealed Work Including Cutting Chases And Making Good The Walls Etc. 16Mm Dia Nominal Outer Dia Pipes Dsr18.8.1 |
| 77 | Providing And Fixing Chlorinated Polyvinyl Chloride (Cpvc) Pipes, Having Thermal Stability For Hot & Cold Water Supply Including All Cpvc Plain & Brass Threaded Fittings I/C Fixing The Pipe With Clamps At 1.00M Spacing. This Includes Jointing Of Pipes & Fittings With One Step Cpvc Solvent Cement And The Cost Of Cutting Chases And Making Good The Same Including Testiang Of Joints Complete As Per Direction Of Engineer In Charge. Concealed Work Including Cutting Chases And Making Good The Walls Etc. 20Mm Dia Nominal Outer Dia Pipes . Dsr18.8.2 |
| 78 | Providing And Fixing Chlorinated Polyvinyl Chloride (Cpvc) Pipes, Having Thermal Stability For Hot & Cold Water Supply Including All Cpvc Plain & Brass Threaded Fittings I/C Fixing The Pipe With Clamps At 1.00M Spacing. This Includes Jointing Of Pipes & Fittings With One Step Cpvc Solvent Cement And The Cost Of Cutting Chases And Making Good The Same Including Testiang Of Joints Complete As Per Direction Of Engineer In Charge. Concealed Work Including Cutting Chases And Making Good The Walls Etc. 32Mm Dia Nominal Outer Dia Pipes. Dsr18.8.4 |
| 79 | Providing And Fixing 45 Cm Long Unplasticised Pvc Connection Pipe With Brass Unions. 45 Cm Length.15Mm Nominal Bore. Dsr18.21.2.1 |
| 80 | Providing & Fixing Cp Brass Bib Cock Of Approved Quality Conforming To Is 8931. 15Mm Nominal Bore. Dsr 18.49.1 |
| 81 | Providing & Fixing C.P. Brass Long Body Bib Cock Of Approved Quality Conforming To Is Standards And Weighing Not Less Than 690 Gms. 15Mm Nominal Bore Dsr 18.51.1 |
| 82 | Providing & Fixing C.P. Brass Angle Valve For Basin Mixer And Gyser Points Of Approved Quality Conforming To Is 8931. 15Mm Nominal Bore Dsr 18.53 |
| 83 | Providing and fixing C.P. brass stop cock (concealed) of standard design and of approved make conforming to IS:8931: 15mm nominal bore. Dsr 18.52.1 |
| 84 | Providing And Fixing Ball Valve (Brass) Of Approved Quality, High Or Low Pressure, With Plastic Floats Complete. 25 Mm Nominal Bore Dsr 18.18.3 |
| 85 | Providing And Fixing Cp Brass Single Lever Lelephonic Wall Mixture Of Quality & Make And As Per Thedirection Of Enginer-In-Charge. 15Mm Dia Nominal Dia. Dsr 17.22B |
| 86 | Providing and fixing gun metal gate valve with wheel of approved quality. 25mm dia nominal bore.Dsr 18.17.1 |
| 87 | Providing and fixing brass stop cock of approved quality. 20 mm nominal bore. Dsr 18.16.2 |
| 88 | Providing And Fixing 8 Mm Dia C.P./S.S. Jet With Flexible Tube Upto 1 Meter Long With S.S. Triangular Plate For Eureopean Type W.C. Of Quality And Make As Approved By Engineer-In-Charge. 15Mm Nominal Bore Dsr 17.16A |
| 89 | Providing And Fixing Cp Brass 32 Mm Size Bottal Trap Of Approved Quality & Make And As Per Thedirection Of Enginer-In-Charge. Dsr 17.22A |
| 90 | Providing & Fixing Ptmt Towl Rail Complete With Brackets Fixed To Wooden Cleats With Cp Brass Screws With Concealed Fitting Arrangement Of Approved Quality And Colour. 600 Mm. Long Towl Rail Length Of 645 Mm. Width 78 Mm. And Effective Height Of 88 Mm, Weighing Not Less Than 190 Gms. Dsr 17.73.2 |
| 91 | Providing And Fixing Ptmt Liquid Soap Container 109 Mm Wide ,125 Mm High And 112 Mm Distance From Wall Of Standerd Shape With Bracket Of The Same Material With Snap Fittings Of Approved Quality And Colour Weighing Not Less Than 105 Gms Dsr 17.71 |
| 92 | Providing And Placing On Terrace (At All Floor Levels) Polyethylene Water Storage Tank Of Approved Brand And Manufacture With Cover And Suitable Locking Arrangement And Making Necessary Holes For Inlet, Outlet And Overflow Pipes But Without Fittings And The Base Support For Tank.For 500 Litres Dsr 18.48 |
| 93 | Constructing Masonry Chamber 60X60X75 Cm Inside, In Brick Work Incement Mortar 1:4 (1 Cement : 4 Coarse Sand) For Sluice Valve, With C.I.Surface Box 100 Mm Top Diameter, 160 Mm Bottom Diameter And 180 Mmdeep (Inside) With Chained Lid And Rcc Top Slab 1:1.5:3 Mix (1 Cement: 1.5Coarse Sand : 3 Graded Stone Aggregate 20 Mm Nominal Size), Includingnecessary Excavation, Foundation Concrete 1:5:10 (1 Cement : 5 Fine Sand: 10 Graded Stone Aggregate 40 Mm Nominal Size) And Inside Plasteringwith Cement Mortar 1:3 (1 Cement : 3 Coarse Sand) 12 Mm Thick, Finishedwith A Floating Coat Of Neat Cement Complete As Per Standard Design :With Common Burnt Clay F.P.S.(Non Modular) Bricks Of Class Designation 15. With Fps Bricks Of Class Designation 15. Dsr 19.7.1.1 |
| 94 | Supplying And Fixing C.L. Cover Without Frame For Manholes :455X610 Mm Rectangular C.L. Cover (Light Duty) The Weight Of The Cover To Be Not Less Than 23 Kg Dsr 19.18.1 |
| 95 | Haunching Of Swr Pipe 90Mm Or 110Mm With Pcc 1:5:10 Cement Concrete ( 1 Cement:5Coarse Sand:10Stone Grit) Dsr 19.2.2 |
| 96 | Providing And Fixing Of Upvc Swr Ring Fit Pipe Of Class B Of Isi Mark Confirming To Is Code 13592 (Make Prince, Supreme Finolex) In Internal Works Of Toilet And Rwp Etc. Including Fixing With Rubber Rings Etc. Including Cost Of All Material, Labour Etc. Complete. 110Mm Diameter MR |
| 97 | Providing And Fixing Of Upvc Swr Ring Fit Pipe Of Class B Of Isi Mark Confirming To Is Code 13592 (Make Prince, Supreme Finolex) In Internal Works Of Toilet And Rwp Etc. Including Fixing With Rubber Rings Etc. Including Cost Of All Material, Labour Etc. Complete. 90Mm Diameter MR |
| 98 | Supply And Fixing Of Upvc S.W.R. Pipe Nahni Trap Size 100X75,110/90 Mm Confirming To Is-14735 Self Cleaning Design Fixed In Pcc 1:2:4 And Supply And Fixing Of 125 Mm Dia Heavy Duty Cp Brass Jali. MR |
| 99 | Supply And Fixing Of Upvc S.W.R. Cowel Confirming To Is-14735. Size 75/90 Mm MR |
| 100 | Supply And Fixing Of Upvc S.W.R. Cowel Confirming To Is-14735. Size 110 Mm MR |
| 101 | Supply And Fixing Of Upvc S.W.R. Upvc Pipe Type B Conferming To Is 13502 Including Jointing Ring Lubricant And Upvc Swr Cupler Conferming Is To Is 14735 Also Including Excavation Of Trenches Cutting Of Wall And Holes And Repairing The Wall Floor And Refilling The Trenches As Before But Excluding Supply And Cost Of Other Fitting Such As Elbow Bend Tee And Y Tee Including All Material Labour And T&P Required For Proper Completion Work. 150 Mm O.D. MR |
| 102 | Providing and fixing in floor and wall face Ringfit UPVC ASTRAL ULTRADRAIN Conventional system for soil and waste water pipes conforming to (HSN CODE: 3917) Type B including jointing with seal ring. (i) Double socketed pipes. 110mm dia P.V.C. pipe. MR |
| 103 | Providing and fixing in floor and wall face Ringfit UPVC ASTRAL ULTRADRAIN Conventional system for soil and waste water pipes conforming to (HSN CODE: 3917) Type B including jointing with seal ring. (i) Double socketed pipes. 90mm dia P.V.C. pipe. MR |
| 104 | Providing & fixing UPVC Floor trap of self cleansing design with CP Jali complete in all respects. (Make : Supreme / Finolex / Prince).P-Trap type Floor Trap 110 x 90mm. MR |
| 105 | Providing and fixing terminal guard. 110mm. MR |
| 106 | Providing and fixing on wall face unplasticised - PVC moulded fittings/accessories for unplasticised Rigid PVC pipes including jointing with seal ring leaving 10 mm gap for thermal expansion. 110mm bend. MR |
| 107 | Providing and fixing on wall face unplasticised - PVC moulded fittings/accessories for unplasticised Rigid PVC pipes including jointing with seal ring leaving 10 mm gap for thermal expansion.90 mm bend.MR |
| 108 | Providing and fixing C.P. brass Two-way angle valve for EWC points & for fixing Ablution Health Fauct of approved quality conforming to15 mm nominal bore. MR |
| 109 | Wiring For Light Point/ Fan Point/ Exhaust Fan Point/ Call Bell Point With 1.5 Sq.Mm Frls Pvc Insulated Copper Conductor Single Core Cable In Surface / Recessed Steel Conduit, With Modular Switch, Modular Plate, Suitable Gl Box And Earthing The Point With 1.5 Sq.Mm Frls Pvc Insulated Copper Conductor Single Core Cable Etc. As Required. Group C. Dsr 1.3.3 |
| 110 | Wiring For Circuit/ Submain Wiring Alongwith Earth Wire With The Following Sizes Of Frls Pvc Insulated Copper Conductor, Single Core Cable In Surface/ Recessed Steel Conduit As Required. 2 X 2.5 Sq . Mm + 1 X 2.5 Sq. Mm Earth Wire. Dsr 1.7.2 |
| 111 | Wiring For Circuit/ Submain Wiring Alongwith Earth Wire With The Following Sizes Of Frls Pvc Insulated Copper Conductor, Single Core Cable In Surface/ Recessed Steel Conduit As Required. 2 X 4 : Sq. Mm + 1 X 4 Sq. Mm Earth Wire. Dsr 1.7.3 |
| 112 | Supplying And Fixing Of Following Sizes Of Steel Conduit Along With Accessories In Surface/Recess Including Painting In Case Of Surface Conduit, Or Cutting The Wall And Making Good The Same In Case Of Recessed Conduit As Required. 25 Mm Dsr 1.20.2 |
| 113 | Supplying And Fixing Suitable Size Gi Box With Modular Plate And Cover In Front On Surface Or In Recess, Including Providing And Fixing 6 Pin 5/6 & 15/16 Amps Modular Socket Outlet And 15/16 Amps Modular Switch,Connection Etc. As Required. Dsr 1.32 |
| 114 | Supplying & Fixing Suitable Size Gi Box Wih Modular Plate And Cover In Front On Surface Or In Recess Including Providing And Fixing 25 A Modular Socket Outlet And 25 A Modular Sp Mcb, “C” Curve Including Connections, Painting Etc. As Required. Dsr 1.57 |
| 115 | Supplying And Fixing Modular Blanking Plate On The Existing Modular Plate & Switch Box Excluding Modular Plate As Required Dsr 1.26 |
| 116 | Supplying And Fixing 3 Pin, 5 A Ceiling Rose On The Existing Junction Box/ Wooden Block Including Connections Etc. As Required. Dsr 1.33 |
| 117 | Extra For Fixing The Louvers/ Shutters Complete With Frame For ExhaustFans Of All Sizes. Dsr 1.51 |
| 118 | Supplying And Fixing Following Size/ Modules, Gi Box Alongwith ModularBase & Cover Plate For Modular Switches In Recess Etc As Required. 4 Module (125Mmx75Mm). Dsr 1.27.3 |
| 119 | Supply And Fixing Of Led Tube Light With Heavy Duty Metal Box Type Tube Light Fitting 1X22 Watt Suitable For Upto 1X 22 Watt Led Polycarbonate Tube Light Complete Including Tube Suitable For Both Surface & Suspended Complete In All Respect. Dsr 23.07 |
| 120 | Supply And Fixing Of Led Tube Light With Heavy Duty Metal Box Type Mirror Light Fitting 10 Watt Led Polycarbonate Tube Light Complete Including Tube Suitable For Both Surface & Suspended Complète In All Respect. MR |
| 121 | Supply And Fixing Of Wall Bricket 10 Watt Led Bulb Polycarbonate Tube Light Complete Including Tube Suitable For Both Surface & Suspended Complète In All Respect. MR |
| 122 | Supplying And Fixing Following Way ,Single Pole And Neutral,Sheet Steel, Mcb Distribution Board, 240 V, On Surface/ Recess, Complete With Tinned Copper Bus Bar, Earth Bar, Din Bar, Interconnections, Powder Painted Including Earthing Etc. As Required. (But Without Mcb/Rccb/Isolator). 12 Way, Double Door. Dsr 2.3.3 |
| 123 | Supplying And Fixing Following Way, Horizontal Type Three Pole And Neutral, Sheet Steel, Mcb Distribution Board, 415 V, On Surface/ Recess, Complete With Tinned Copper Bus Bar, Neutral Bus Bar, Earth Bar, Din Bar, Interconnections, Powder Painted Including Earthing Etc. As Required. (But Without Mcb/Rccb/Isolator). 4 Way Double Door. Dsr 2.4.1 |
| 124 | Supplying And Fixing Following Rating, Four Pole, 415 V, Mcb In The Existing Mcb Db Complete With Connections, Testing And CommissioningEtc. As Required. 40 Amps 4P Mcb. Dsr 2.13.1 |
| 125 | Supplying And Fixing 5 Amps To 32 Amps Rating, 240/415 Volts, \\"C\\" Curve, Miniature Circuit Breaker Suitable For Inductive Load Of Following Poles In The Existing Mcb Db Complete With Connections, Testing And Commissioning Etc. As Required. Single Pole 6-32Amp C Curve Dsr 2.10.1 |
| 126 | Supplying And Fixing Single Pole Blanking Plate In The Existing Mcb Db Complete Etc. As Required. Dsr 2.11 |
| 127 | Providing and fixing circular/ Hexagonal cast iron or M.S. sheet box for ceiling fan clamp, of internal dia 140 mm, 73 mm height, top lid of 1.5 mm thick M.S. sheet with its top surface hacked for proper bonding, top lid shall be screwed into the cast iron/ M.S. sheet box by means of 3.3 mm dia round headed screws, one lock at the corners. Clamp shall be made of 12 mm dia M.S. bar bent to shape as per standard drawing. CIVIL DSR 10.18 |
| 128 | Supply and fixing of wall bricket 10 watt LED bulb Polycarbonate tube light complete Including tube suitable for both surface & suspended Complète in all respect. MR |
| 129 | Supply, Installation, Testing and Commissioning of ceiling fan with BrushLess Direct Current (BLDC) Motor, class of insulation: B, 3 nos. metal(Aluminum alloy) blades, 30 cm long down rod, 2 nos. canopies, shackle kit,safety rope, copper winding, steel/Al body Power Factor not less than 0.9,Service Value (CM/M/W) minimum as below, 350 RPM (tolerance as per IS :374-2019), THD (Total Harmonic Distortion) less than 10%, remote(preferably mobile app based) for speed control and all remainingaccessories including safety pin, nut bolts, washers, temperature rise=75degree C (max.), insulation resistance more than 2 mega ohm, suitable for230 V, 50 Hz, single phase AC Ceiling Fan compliant to IS 374:2019 fan Supply, earthing etc. complete as req 1200mm, service value ≥ 6.0 CM/Min/Watt, air delivery 210 CM/Min (Minimum). |
| 130 | Supply and fixing of Exhaust-Fan 200mm Sweep OF APPROVED BRAND Complète in all respect. Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Sep 26, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedOct 17, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 15 daysOct 17, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 15 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender