Tender For Provision Of Guard Room With Toilets Under Age Br (P) Of Ge (P) Nagrota
Tender Value
19.67 Lakhs
Estimated cost
Bid Submission
19 Oct 2026
15 days left
EMD
39400
Bank guarantee accepted
Document Fee
500
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Nagrota/ JAMMU → Jammu and Kashmir
EMD Exemption
Not Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for Provision Of Guard Room With Toilets Under Age Br (P) Of Ge (P) Nagrota
BOQ
| Sl. No. | Item Description |
| 1 | BR PORTION Surface excavation n.exc (not exceeding) 30 cm deep and averaging 15cm deep and getting out any kind of soil complete all as specified and directed by Engineer-in-Charge. |
| 2 | Excavation in trenches not exceeding 1.5 Mtr wide and not exceeding 1.5 Mtr in deep in soft/disintegrated rocks getting out and levelling of bottom surface to required level all as specified and directed by Engr-in-charge. |
| 3 | Earth work in excavation by mechanical means (Hydraulic excavator)/ in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, lift upto 1.5 m, including getting out any kind of soil the excavated soil and disposal of surplus excavated soil as directed, with in a lead of 50 m. complete all as specified and directed by Engineer-in-Charge. |
| 4 | M&L for cement concrete Type D2 1:4:8 (40mm graded crushed aggregate) in foundations,filling and mass concrete. complete all as specified and directed by Engineer-in-Charge. |
| 5 | RCC (Design mix) M-25 for foundations, including rafts, footings, foundation beams; plinth beams; bases for columns, etc.; basement slabs, under-reamed piles and mass concrete complete all as specified and directed by Engineer-in-Charge. |
| 6 | RCC (Design mix) M-25 for Columns, pillars, piers, posts and struts complete all as specified and directed by Engineer-in-Charge. |
| 7 | RCC (Design mix) M-25 for Beams, cantilevers, bressummers, lintels over 1.5m span complete all as specified and directed by Engineer-in-Charge. |
| 8 | RCC (Design mix) M-25 for Slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves complete all as specified and directed by Engineer-in-Charge. |
| 9 | M&L for Treating the backfill in contact with foundation at the rate of 7.5 litres of emulsion per square metre of vertical surface (Area of the sub structure in contact with backfill to be measured). Complete all as specified and directed by Engineer-in-Charge. |
| 10 | M&L for Treating the top surface of filled earth at the rate of 5 litres of emulsion per square metre of surface complete all as specified and directed by Engineer-in-Charge. |
| 11 | M&L for Treating the soil along with external perimeter of building at the rate of 2.25 litre of emulsion per metre of the perimeter wall complete all as specified and directed by Engineer-in-Charge. |
| 12 | Returning, filling in, including spreading, levelling, watering and well ramming in layers not exc 25 cm. Complete all as specified and directed by Engineer-in-Charge. |
| 13 | Removing excavated material exc. 250 m but n exc. 500 m and depositing where directed. Complete all as specified and directed by Engineer-in-Charge. |
| 14 | M&L formwork to flat sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams; and similar work; vertical or to batter. Complete all as specified and directed by Engineer-in-Charge. |
| 15 | Rough finished surfaces of concrete flat formwork Square, Circular rectangular or polygonal to sides of pillars, posts, struts, piers, columns and stanchions. Complete all as specified and directed by Engineer-in-Charge. |
| 16 | Rough finished surfaces of concrete flat formwork to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelves including sup- ports, overhangs, etc. also splays between floors and beams, etc. Complete all as specified and directed by Engineer-in-Charge. |
| 17 | Rough finished surfaces of concrete flat formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200mm thick (Horizontal or sloping). Complete all as specified and directed by Engineer-in-Charge. |
| 18 | Rough finished surfaces of concrete flat formwork to edges of concrete flats, breaks in floors, openings in concrete walls, floors and roofs and sides of RCC/PCC bands in walls, horizontal or sloping, and similar work all exceeding 20cm wide. Complete all as specified and directed by Engineer-in-Charge. |
| 19 | Mild steel bars 10mm dia and over, cut to length, bent to shape required, ncluding cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips. Complete all as specified and directed by Engineer-in-Charge. |
| 20 | Mild steel bars but 5mm dia and over upto and including 10mm dia in stirrups, spacers and binders, cut to length, bent to shape required, ncluding cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips. Complete all as specified and directed by Engineer-in-Charge. |
| 21 | Mild steel bars 6mm to 8mm dia., cut to length, bent to shape required, ncluding cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips. Complete all as specified and directed by Engineer-in-Charge. |
| 22 | M&L for brickwork with subclass ‘B’ bricks, straight or curved on plan exc 6m mean radius built in CM 1:6. Complete all as specified and directed by Engineer-in-Charge. |
| 23 | M&L for brickwork with subclass ‘B’ bricks, straight or curved on plan to any radius in half brick thick walls built in CM 1:4 Complte all as directed |
| 24 | M&L for 2nd class HW 35mm thick flush shutters, solid core construction, but with particle board core and plywood face panels, commercial type on both sides. Complete all as specified and directed by Engineer-in-Charge. |
| 25 | S&F for pressed steel frames for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc. size 105 x 60mm including for one shop coat of priming complete all as specified and directed |
| 26 | S&F for pressed steel frame for door with two rebate incl necessary fixing lugs,hold fast,hings,lock strike plate 125 x 60mm including for one shop coat of priming complete all as specified and directed. |
| 27 | M&L Cement concrete 1:3:6 Type C-0 (12.5 mm graded crushed stone aggregate) as cooping, for lintels upto 1.5m clear span, cills, steps; seismic and other similar bands, plinth courses, string courses, lacing courses, parapets and railings upto 60 cm in height, kneelers, apex stones, bed plates, back filling of steel chowkhats, kerbs water troughs and the like including weathering, slightly rounded or chamfered angles and throating including necessary form work, complete all as specified and directed. |
| 28 | S&F for solid PVC Door Frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S. Square tube, suppling & fixing in opening as per specification. Complete all as specified and directed by Engineer-in-Charge. |
| 29 | S&F for factory Made Solid PVC Moulded Door Shutter, 28 to 30mm thick (stiles), with 2, 4, or 6 raised panel design with 2mm thick Moulded PVC Sheet on the front face & 2mm plain colour PVC sheet on back face with particle board Core , supplying & fixing in frame at site as per specification. Complete all as specified and directed by Engineer-in-Charge. |
| 30 | M&L for 2nd class HW 35mm thick Glazed and skeleton shutters, open rebated and prepared to receive glass, gauze, etc. (without sash bars), edges of framing plain, chamfered or rounded. fitted with cut and mitred beads for securing glass, etc.; sizes of me-mbers of shutters as specified in SSR Part I, Section 8, clause 8.24 (a); supplied and fitted to steel chowkats. Complete all as specified and directed by Engineer-in-Charge. |
| 31 | S&F for box type steel window frame with side hung double shutter with provision for desert cooler / AC (inside for wiremesh & out side for glass) including guard bar, hinges, steel, handle, tower bolt and steel peg stay complete with glazing bar dovetailed or welded including a coat of red oxide after preparation of surface before fixing and fixed steel window shall be conforming to relevant IS complete all as directed (Note : Wire mesh and sheet glass shall be meaured and paid separately). |
| 32 | S&F for sheet glass 4mm thick ordinary qaulity and glazing with oil putty in sqaures n exc 0.5 sqm each panes etc all as specified. |
| 33 | S&F for galvanised mild steel wire cloth, 0.56mm nominal dia of wire and average width of aperture 1.18mm and fixed with tinned tacks, or galvanised wire staples etc all as specified. |
| 34 | S&F for 150mm long aluminium anodised barrel tower bolt of extruded section and fixed. Complete all as specified and directed by Engineer-in-Charge. |
| 35 | S&F for 300mm long aluminium alloy, anodised, sliding door bolt with hasp, stapple (bolt type) and fixing clips of sheet cast or extruded sections and fixing bolts and sliding bolts of extruded section or cast aluminium alloy and fixed. Complete all as specified and directed by Engineer-in-Charge. |
| 36 | S&F for 100mm mild steel butt hinges, medium weight, cold rolled and fixed. |
| 37 | S&F for 150mm long aluminium handles cast type, anodised and fitted. Complete all as specified and directed by Engineer-in-Charge. |
| 38 | S&F for 300mm long ordinary MS rat tail rod pattern springs incl roller and roller plate. Complete all as specified and directed by Engineer-in-Charge. |
| 39 | S&F for box type steel ventilators frame with top hung double shutter with frame (inside for wiremesh & outside for glass), incl guard bar, hinges, steel handle tower bolt and steel peg stay complete with glazing bar dovbetailed or welded including a coat of red oxide after preparation of surface before fixing, steel ventilators shall be conforming to relevant IS complete and directed (Note : Wire mesh and sheet glass shall be meaured and paid separately). |
| 40 | M&L for two coats of synthetic enamel paint over a coat of pink primer on new wood or wood surfaces, over 10 cm width or girth incl preparation of surfaces. Complete all as specified and directed by Engineer-in-Charge. |
| 41 | M&L for two coats of synthetic enamel paint on new steel surfaces, over a coat of primer over 10 cm width or girth incl preparation of surfaces. Complete all as specified and directed by Engineer-in-Charge. |
| 42 | S&F for mild steel drapery rod 25mm dia plastic coated fixed on wall including providing rings through out the length at some intervals complete all as specified and directed |
| 43 | S&F for mild steel brackets powder coated at both ends to hang curtain rod and colour all as specifid and directed |
| 44 | S&F for PVC ball shaped knobs at both end of curtain rod and colour all as specifid and directed. |
| 45 | M&L for rendering 15mm thick on fair faces of brick work or concrete surfaces in cement mortar 1:4 without using extra cement complete all as specified. |
| 46 | M&L for rendering 15mm thick on fair faces of brick work or concrete surfaces in cement mortar 1:6 without using extra cement complete all as specified. |
| 47 | Rendering 5mm thick on fair faces of brick work or concrete surfaces cement mortar 1:3 without using extra cement complete all as specified |
| 48 | M&L for preparing new plastered surfaces of wall and applying two coats of cement based paint over a coat of primer complete all as specified . |
| 49 | M&L for preparing new plastered surfaces of wall and applying two coats of oil bound distemper over a coat of primer incl 3mm thick wall care putty complete all as specified . |
| 50 | M&L for preparing new plastered surfaces of ceiling, chajjas facia etc. and applying three coat of white wash complete all as specified and directe |
| 51 | M&L for 100mm thick Cement concrete type D- 2, 1:4:8 (40mm graded aggregate) as in flooring complete all as specified |
| 52 | M&L for 75mm thick Cement concrete type B- 2, 1:2:4 (40mm graded aggregate) as in flooring complete all as specified |
| 53 | M&L for pre polished Machine cut kota stone slab size not less then 550x550 (single piece using in treads) flooring 18-20mm thick over cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing, cutting in square or rectangular and polishing including 15mm thick screed bed in CM 1:4 complete all as specified and directed.complete |
| 54 | M&L 12-15mm thick Pre polished Kota stone slab for skirting, dado and pillar laid over cement screed and jointed including rubbing, cutting in square or rectangularand polishing including 15mm thick screed bed in CM 1:3 complete all as specified and directed. Complete |
| 55 | M&L for Non - skid Ceramic coloured tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors etc. set and jointed in neat cement slurry and pointed in coloured cement to match the surface over and including 15mm thick screed bed in CM 1:4 complete all as specified and directed. |
| 56 | M&L glazed, coloured, ceramic, tiles of size (350x600x7-10mm/300x450x7mm thick), on vertical surfaces, such as skirting, dadoes, etc set and jointed in neat cement slurry and pointed in coloured cement to match with the surface over and including 10mm thick backing coat in CM 1:3 complete all as specified and directed. |
| 57 | Forming Contraction (Dummy) joints 65mm deep x 10mm wide, filled with sealing compound Grade A. Complete all as specified and directed by Engineer-in-Charge. |
| 58 | M&L for PCC 1:3:6 type C2 (75 mm thick as in plinth protection & finishing the surface even & fair W/o using extra cement complete all as specified and directed. |
| 59 | M&L for hardcore of gauge n exc. 63 mm, deposited, spread and levelled in layers n exc. 15 cm thick, watered and rammed to a true surface Broken stone or boulders. Complete all as specified and directed by Engineer-in-Charge. |
| 60 | M&L for vitreous China squatting pan, ‘Orissa’ pattern, size 580 x 440 mm white, with integral foot rests (excluding flushing cistern and flush pipe) including provision of lean concrete bedding connection to drain out pipe, to flush pipe and antisyphonage pipe etc, complete all as specified. |
| 61 | M&L for 10 Ltr PVC valveless, syphonic action type, flushing cistern, low level, white, with inlet, ball valve, float and handle including brackets for fixing to wall, Flush pipe of polyethylene of low or high density or PVC. 32 mm dia, for low level cistern. Complete all as specified and directed by Engineer-in-Charge. |
| 62 | M&L for Vitreous Chiina wash basin, white, flat back, size 580x450 iron excluding taps, waste, chain and plug and porcelain stopper but including brackets for fixing to wall , 32mm dia Waste fittings, brass, chromium plated for glazed ware sinks, basins, etc.with long screwed shanks and fly-nuts, flange end bedded in red lead cement and other end fixed. Complete all as specified and directed by Engineer-in-Charge. |
| 63 | M&L for 20mm thick Granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, window- cills, cooking platforms and like in cement mortar (1:4) including moulding to edge of granite, pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite and including 15mm thick screed bed in CM 1:6 complete all as specified and directed |
| 64 | M&L Reinforced cement concrete (nominal mix type B1 1:2:4 (20 mm graded aggregate) in Slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the ikecomplete all as specified and directed. |
| 65 | S&F for stainless steel wall mounted soap dish holder fixed to plugs with chromium plated brass screws all as specified and directed |
| 66 | S&F for urinal spreader of PTMT any colour for fixing with 15 mm dia pipe. (Minimum weight 60gms). Complete all as specified and directed by Engineer-in-Charge. |
| 67 | S&F for vitreous China bowl urinal flat back, size of 465 x 355 x 265 mm white (minimum), with grating and union for discharge pipe (excluding flushing cistern, flush pipe and waste pipe). Complete all as specified and directed by Engineer-in-Charge. |
| 68 | S&F for 15 mm dia GI tubing medium grade with all fittings and fixed complete to walls or laid in floors. Complete all as specified and directed by Engineer-in-Charge. |
| 69 | Cutting chases, pinning in. making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc.; and cutting chases for concealed water tubing or concealed conduit wiring, etc., and making good, cutting not exc 10 cm girth. (in brick walls). Complete all as specified and directed by Engineer-in-Charge. |
| 70 | S&F for 20mm dia GI tubing medium grade with all fittings and fixed complete to walls or laid in floors. Complete all as specified and directed by Engineer-in-Charge. |
| 71 | S&F for bib tap fancy type 15mm dia cast copper alloy chromium plated with capstan handle screwed down for iron pipe or for brass ferrule all as specified and directed |
| 72 | S&F for 15mm dia swivel shower of PTMT any colour for fixing with 15mm pipe incl 195mm long with bend of 45degree with flange of PTMT any colour. (Minimum weight 40gms). Complete all as specified and directed by Engineer-in-Charge. |
| 73 | S&F for 15mm dia Pillar taps, cast copper alloy, with capstan heads, chromium plated, screwed down high pressure, with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly-nuts, screwed for iron pipe and fixed. Complete all as specified and directed by Engineer-in-Charge. |
| 74 | S&F for angle cock/ stop valve cast copper alloy 15mm dia fancy type chromium plated, with long shank and cup (concealed type) screwed down, high pressure, with capstan handle screwed both ends for iron pipes or for unions all as specified and directed |
| 75 | Supply and fixing 50mm dia low density polyethylene pipes (LDPE) of pressure rating 6 kgf/ cm2 fixed complete to walls, ceilings or floors including elbows, unions, tees, reducing tees, adoptors, sokets, plug house clips etc and fixing to walls etc complete with saddles (snap clips), wall clips hooks complete all as specified and directed. |
| 76 | S&F for 20mm bore Gun-metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed. Complete all as specified and directed by Engineer-in-Charge. |
| 77 | S&F for glass corner shelf of 300mm long all complete all as specified and directed by Engineer-in-Charge. |
| 78 | S&F for 600mmx450mm bevelled edge mirror of selected quality glass, mounted on 6mm thick AC building board or commercial plywood and fixed to wooden plugs with chromium plated brass screws and cup washers. Complete all as specified and directed by Engineer-in-Charge. |
| 79 | S&F for brass CP Tubular towel rail, 20mm dia, D type, 60cm long between flanges. Complete all as specified and directed by Engineer-in-Charge. |
| 80 | S&F for PVC connections 15mm size with PTMT nuts of length 600mm. Complete all as specified and directed by Engineer-in-Charge. |
| 81 | S&F for 1000 Ltr Rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top) hoisted and fixed in position all as specified in SSR Part I. Complete all as specified and directed by Engineer-in-Charge. |
| 82 | S&F for 20mm bore Ball valves high pressure of PTMT with epoxy coated Aluminium rod & highdensity plastic ball screwed for iron pipe and fixed. Complete all as specified and directed by Engineer-in-Charge. |
| 83 | M&L for 10 mm thick rendering in CM 1:4 mixed with water proofing compound @2% of cement over roof surfaces finished even and smooth without using extra cement complete all as specified Note:- WPC Mesured and Paid Separately. Complete all as specified and directed by Engineer-in-Charge. |
| 84 | Supplied only liquid water proofing compound ISI Marked complete all as specified and directed. |
| 85 | M&L for PCC 1:2:4 type B1 (20mm graded aggregate) 50mm thick as in roof padding finished even and smooth without using extra cement. Complete all as specified and directed by Engineer-in-Charge. |
| 86 | M&L for applying evenly a tack coat of industrial bitumen 85/25 grade @ 1.2 Kg/Sqm including bitumen primer @ 3.50 Kg/Sqm over plaster surfaces of roof. Complete all as specified and directed by Engineer-in-Charge. |
| 87 | M&L for laying APP (static polypropylele) modified membrance 3mm thick and weight not less than 3.00 Kgs per Sqm with 160 GSM/Sqm non woven polyester mat as centre core reinforcement laid with 75mm side over lap and 100mm end lap the membrane has to be laid with LPG tourch and over lap sealed and finished neat over roof and grouting with mixture of white cement and marble powder over roof complete all as specified and directed by Engr-in-Charge. NOTE : APP based polimeric membrane of approved manufacturer will be laid/fixed by authorised person of the same manufacturers units asper relevent IS. |
| 88 | S&F Precast factory made plain cement concrete tiles 30cm x 30cm x 25mm thick, set, jointed and pointed in neat cement slurry in floors jointed and pointed with grey cement and pigment including screed bed or bedding layer of mortar 15 mm thick in CM (1:4) complete all as specified and directed. |
| 89 | M&L for Cast iron cowl for 50mm bore pipe complete all as specified and directed. |
| 90 | M&L for 50mm bore Cast iron soil, waste and vent pipes (Sand cast) in any length with or without ears, with cement joints, fixed to walls, complete all as specified and directed |
| 91 | M&L for Cast iron bends (any radius), diminishing pieces or tapers (larger bore measured,for pipes of bore 50mm complete all as specified and directed |
| 92 | M&L for Cast iron bends (any radius) with duck's foot or heel rest fitted with oval access doors, for pipes of bore 100mm, complete all as specified and directed. |
| 93 | M&L for 100mm bore Cast iron soil, waste and vent pipes (Sand cast) in any length, with or without ears, with cement joints laid in trenches or in floors, complete all as specified and directed |
| 94 | M&L for Cast iron bends (any radius) with duck's foot or heel rest fitted with oval access doors, for pipes of bore 75mm, complete all as specified and directed. |
| 95 | M&L for Cast iron Bends (any radius), diminishing pieces or tapers for pipes of bore 75mm, complete all as specified and directed. (larger bore measured) |
| 96 | M&L for 75mm bore Cast iron soil, waste and vent pipes (Sand cast) in any length, with or without ears, with cement joints laid in trenches or in floors, complete all as specified and directed |
| 97 | M&L for Cast iron sanitary connection socket to fit WC out-let for pipes of bore 100mm complete all as specified and directed |
| 98 | M&L for Cast iron bends (any radius) with duck's foot or heel rest, for pipes of bore 100mm, complete all as specified and directed. |
| 99 | M&L for Cast iron Floor trap with stainless steel grating including jointing to waste pipe fixed in cement concrete type B-1 (1:2:4) with cement joint, dia of outlet 75mm, complete all as specified and directed. |
| 100 | M&L Stack clamps for 50mm bore out of 50 mm by 5 mm flat iron and 16mm dia round iron stays, including bolts and nuts and securing ends of stays to wall or roof complete all as specified and directed. |
| 101 | M&L for providing lead joints for 100mm dia in lieu of cement joints for pipes embedded in masonry or concrete complete all as specified and directed. |
| 102 | Cement Concrete bed Type D2 1:4:8 (40mm crushed stone graded aggregate), to 100mm bore drain pipes including packing under, and haunching against the sides of pipes after they are laid and tested complete all as specified and directed. |
| 103 | M&L for 150mm bore Reinforced concrete pipes, class NP3, laid and jointed complete with collars complete all as specified and directed. |
| 104 | M&L for cement Concrete bed Type D2 1:4:8(40mm graded aggregate) to 150mm bore drain pipes including packing under, and haunching against the sides of pipes after they are laid and tested complete all as specified and directed. |
| 105 | M&L for PCC 1:4:8 type D-2 ( 40mm graded crushed stone aggregate) as if foundation or sub base mass concrete complete all as specified and directed. |
| 106 | M&L for brickwork with sub class \\"B\\" bricks straight or curved on plan exc 6 m mean radius built in cement mortar 1:4 all as specified. |
| 107 | M&L for rendering 15 mm thick in CM 1:4 on brick work or concrete surfaces finished even and smooth without using extra cement including mixing of liquid warerproofing compound in the proportion as per manufacturer's instrutions. (WPC will be measured and paid separately) |
| 108 | Supply only Liquid water proofing compound ISI Marked Complete all as percified and directed |
| 109 | M&LProviding precast cement concrete 1:2:4 type B-1 using 20 mm graded crushed stone aggregate as in coping etc including necessary formwork all as specified and directed. |
| 110 | Providing precast cement concrete 1:2:4 type B-1 using 20 mm graded crushed stone aggregate as in manhole cover etc set in cement mortar 1:6. including necessary formwork all as specified and directed. |
| 111 | Providing cement concrete 1:4:8 type D-2 using 40mm greaded crushed stone aggregate in manhole channel complete all aspecified and directed. |
| 112 | Extra for forming fair finished drain or channel 30cm inner girth in cemernt concrete , using extra cement including forms, moulds, mittered/stoped ends etc complete all as specified and directed. |
| 113 | Add or deduct for each 25 mm girth or part thereof over or under 30cm for srl item No 112 above |
| 114 | EM PORTIONSupply and Laying Tubes (Pipe), 'medium grade', galvanised, with all fitting;laid in trenches including fitting 40 mm dia. Complete all as specified and directed by Engineer-in-Charge. |
| 115 | Supply and Laying Tubes (Pipe), 'medium grade', galvanised, with all fitting;laid in trenches including fitting 25 mm dia. Complete all as specified and directed by Engineer-in-Charge. |
| 116 | Supply and fix Gun Metal, globe or gate valves, with iron wheel head, screwed both ends for pipe and fixed of size 40 mm. Complete all as specified and directed by Engineer-in-Charge. |
| 117 | Supply and fix Gun Metal, globe or gate valves, with iron wheel head, screwed both ends for pipe and fixed of size 25 mm. Complete all as specified and directed by Engineer-in-Charge. |
| 118 | M&L for cutting of existing pipeline of 100/150 mm dia for taking branch connection alongwith insertion of CI/GI Tee and connecting material such as joint, nut bolts, etc all as required at site. Complete all as specified and directed by Engineer-in-Charge. |
| 119 | Material and labour for construction of masonary valve pit of size 60x60x60 cm complete with Ms angle frame and MS sheet cover of 3.15 mm thickness including excavation and earth work. Complete all as specified and directed by Engineer-in-Charge. |
| 120 | Supply and fix Desert cooler electric driven (single phase), having nominal air flow capacity of 4000 Cum per hour (or nearest size) Steel body |
| 121 | Supply, installation, commis-sioning of Water cooler fully stainless steel, electric driven single phase having 40 litre and nominal cooling capacity of 20 Litres per hour. |
| 122 | Supply and fix Voltage stabilizer for automatic operation, single phase naturally air cooled indoor type & designed for input variation between 170 V to 250 V with output voltage stabilized at 230 V with accuracy of ± 2.5% and of capacity 1.0 KVA |
| 123 | S&F for cable XLPE insulated screened PVC bedded galvanized steel striper wire armoured electric power cables heavy duty with standard aluminium conductor of size 2 core 16 Sqmm. |
| 124 | M&L for DWC pipe for cable protection of ID 32 mm complete with all fitting all as specified & directed by Engr-in-Charge. |
| 125 | M&L for Point wiring for One light point (T/L, Batton Hoder, Mirror Light, Bldg Sec Light & Bulk Head) controlled by one switch 5 Amp SP one-way complete with 1.5 Sq mm (nominal area) PVC insulated, unsheathed and multi strand copper conductor FRLS cable (ISI marked) drawn into and including PVC concealed conduit (medium quality) and conduit fittings including 1.5 Sq mm PVC insulated unsheathed and multi stranded copper conductor FRLS cable as earth wire to common earth and connecting to earth dolly including suitable size Modular MS sunken box for fixing of modular switches,sockets,regulators with frame and top white cover plate and machine made brass screw and washers etc complete all as specified and directed for one light point controlled by one one way switch. |
| 126 | - Ditto - all as per item No - 125 above but for one ceiling fan/exhaust fan point. |
| 127 | - Ditto - all as per item No - 125 above but for one 3 pin 5 amp socket on same board all as directed. |
| 128 | - Ditto - all as per item No - 125 above but for one 3 pin 5 amp socket on indipendant board all as directed. |
| 129 | - Ditto - all as per item No -125 above but with 2.5 sqmm copper conductor for 15 amp socket with 2.5 sqmm earth continuity conductor. Complete all as specified and directed by Engineer-in-Charge. |
| 130 | S&F for modular snap switch SP one way 5/6 Amps suitable for 1 Module. Complete all as specified and directed by Engineer-in-Charge. |
| 131 | S&F for modular socket 3 pin 5/6 Amps suitable for 2 Module. Complete all as specified and directed by Engineer-in-Charge. |
| 132 | S&F for modular snap switch SP one way 15/16 Amps suitable for 1 Module. Complete all as specified and directed by Engineer-in-Charge. |
| 133 | S&F for modular socket 5 pin 15/16 Amps suitable for 2 Module. Complete all as specified and directed by Engineer-in-Charge. |
| 134 | S&F for ceiling rose surface backalite two to three terminals. Complete all as specified and directed by Engineer-in-Charge. |
| 135 | Supply and fix lamp holder insulated body with back plate suitable for any type of fitting. Complete all as specified and directed by Engineer-in-Charge. |
| 136 | Supply and fixing LED Batten lights fttings 1 x 20Watt, 220V, AC. Complete all as specified and directed by Engineer-in-Charge. |
| 137 | Supply and fix LED Batten 5 Watt cool white tube light with 500 Lumen for bathroom mirror fitting. Complete all as specified and directed by Engineer-in-Charge. |
| 138 | Supply and fix LED lamp 9 Watt. Complete all as specified and directed by Engineer-in-Charge.. |
| 139 | Supply and fixing LED bldg Security light fitting 25 Watt 230 V AC outdoor type with high pressure die cast aluminum hosing and heat resistant complete with driver, lamp bracket with impact and corrosion resistant including thermal management in multiple optics complete with IP 65/66 protection. Complete all as specified and directed by Engineer-in-Charge. |
| 140 | Supply and fixing ceiling fans complete with blades, down rods, Fan Regulator and accessories, 230 V, 1200mm sweep. Min air delivery 210 CFM with service value 6.00 BEE. Five star rated with brushless direct current motor (BLDC). Complete all as specified and directed by Engineer-in-Charge. |
| 141 | Supply and fix electric water heater,storage type steel body with copper inner tank and heating element upto 2 KW capacity 25 litre, BEE 5 Star rated complete with all accessories such as safety valve, thermostate, NRV, connection piece etc. Complete all as specified and directed by Engineer-in-Charge. |
| 142 | Supply and fix exhaust fan made of sturdy Engineering plastic complete with louvers shutter, voltage 230V, 50 Hz, RPM 1200, Copper winding of sweep 250 mm. Complete all as specified and directed by Engineer-in-Charge. |
| 143 | S&F sheet metal enclosure for DB's , MCB DB SPN 8 way double door. Complete all as specified and directed by Engineer-in-Charge. |
| 144 | Supply and fixing MCB SPN 240 Volts 32 Amps complete all as specified and directed by Engineer-in Charge. |
| 145 | Supply and fixing MCB SP 240 Volts 6 Amps to 32 Amps complete all as specified and directed by Engineer-in Charge. |
| 146 | S&F for sub main wiring with PVC insulated, FRLS cable 2 single core 6 Sq mm 1100 V grade with stranded copper conductor on and incl PVC rigid non metalic conduit (ISI marked) in concealed incl all specials like joint, elbow,Tee, junction , bend etc and provision of PVC insulated copper conductor single core 6 sq mm for earth continuityconductor complete all as directed by Enginer-in-charge. |
| 147 | M&L for Earthing complete with GI earth plate 60cm ×60cm ×3 mm thick electrode buried directly in ground (earth pit not less than 2.25 meters deep below ground level) with top edge of the plate not less than 1.5 meter below normal ground level connected to GI earth wire lead 4 mm dia by means of bolts, nuts, check nuts and washer of galvanized iron or steel all as shown in electrical plate No 5 of SSR Part-I connected to continuous earth wire on earthing point all as specified and testing on completion, including provision of GI earth lead wire protected by 15 mm dia GI light grade protection pipe from test point to main board and 20mm GI medium grade watering pipe funnel, PCC earth pit and RCC cover charcoal, salt and GI wire including excavation and earth work etc complete all as directed at site. Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Sep 26, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedOct 19, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 15 daysOct 21, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 17 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender