Tender For Remodeling & Renovation Of Quarter No-C-1,C-2 & B-1 Of Chinsurah Irrigation Colony For Relocation The Damodar Irrigation Revenue Division No-Iii
Tender Value
11.25 Lakhs
Estimated cost
Bid Submission
12 Oct 2026
6 days left
EMD
22506
Bank guarantee accepted
Document Fee
Ref. Documents
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Hooghly → West Bengal
EMD Exemption
Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for Remodeling & Renovation Of Quarter No-C-1,C-2 & B-1 Of Chinsurah Irrigation Colony For Relocation The Damodar Irrigation Revenue Division No-Iii
BOQ
| Sl. No. | Item Description |
| 1 | Dismantling artificial stone flooring up to 50 mm. thick by carefully chiseling without damaging the base and removing rubbish as directed within a lead of 75 m.a) In ground floor including roof. |
| 2 | Dismantling all types of masonry excepting cement concrete plain or reinforced, stacking serviceablematerials at site and removing rubbish as directed within a lead of 75 m.a) In ground floor including roof. |
| 3 | b) Extra rate for each addl. Floor over the rate of ground floorIn 2 nd floor |
| 4 | Dismantling R.C. floor, roof, beams etc. including cutting rods and removing rubbish as directed within a lead of 75 m. including stacking of steel bars.(a) In ground floor including roof. |
| 5 | b) Extra rate for each addl. Floor over the rate of ground floorIn 1 st floor |
| 6 | In 2 nd floor |
| 7 | Cleaning the concrete surface by removing dirt and debris, marking defective locations and removing loose concrete by careful stripping until hard surface is exposed, cutting the concrete to regular shape, wire brushing the exposed surface and removing debris from site complete as per direction of the Engineer - in - Charge. |
| 8 | Plaster (to wall, floor, ceiling etc.) with sand and cement mortar including rounding off or chamfering corners as directed and raking out joints including throating, Nossing and drip course, scaffolding/staging where necessary (Ground floor).[Excluding cost of chipping over concrete surface](ii) With 1:4 cement mortar(c) 10 mm thick plaster |
| 9 | (b) 15 mm thick plaster |
| 10 | Extra for each additional floor over the rate for ground floor for Item No. 5(ii) Internal plaster(a) Up to 4th floorIn 1 st Floor |
| 11 | In 2 nd Floor |
| 12 | (i) External plaster(a) Up to 4th floorIn 1 st Floor |
| 13 | In 2 nd Floor |
| 14 | Stripping off worn out plaster and raking out joints of walls, ceilings etc. up to any height and in any floor including removing rubbish within a lead of 75m as directed. |
| 15 | Neat cement punning about 1.5mm thick in wall, dado, windowsill, floor etc.Note:Cement 0.152 cu.m per100 sq.m. |
| 16 | Ordinary Cement concrete (mix 1:2:4) with graded stone chips (20 mm Nominal size) excluding shuttering and reinforcement, if any, in ground floor as per relevant IS codes.a) Pakur Variety |
| 17 | Add extra over the rate of ground floor for basement and each additional floor above ground floor for items 9(i) up to 4 th floor.In 2 nd floor |
| 18 | Ordinary Cement concrete (mix 1:1.5:3) with graded stone chips (20 mm Nominal size) excluding shuttering and reinforcement if any, in ground floor as per relevant IS codes.i) Pakur Variety |
| 19 | Add extra over the rate of ground floor for basement and each additional floor above ground floor for items 17(i) up to 4 th floor.1 st Floor |
| 20 | 2nd Floor |
| 21 | Hire and labour charges for shuttering with centering and necessary staging up to 4 m using approved stout props and thick hard wood planks of approved thickness with required bracing for concrete slabs, beams and columns, lintels curved or straight including fitting, fixing and striking out after completion of works (up to roof of ground floor)(a) 25 mm to 30 mm thick wooden shuttering as per decision & direction of Engineer-In-Charge. |
| 22 | (c) Steel shuttering or 9 to 12 mm thick approved quality ply board shuttering in any concrete work |
| 23 | (d) Extra for works beyond the roof of ground floor per additional floor(i) up to 4th (per floor) and in basement.1 st Floor |
| 24 | 2nd Floor |
| 25 | Reinforcement for reinforced concrete work in all sorts of structures including distribution bars, stirrups, binders etc initial straightening and removal of loose rust (if necessary), cutting to requisite length, hooking and bending to correct shape, placing in proper position and binding with 16 gauge black annealed wire at every intersection, complete as per drawing and direction.(a) For works in foundation and up to roof of ground floor/up to 4 m(i) Tor steel/Mild SteelII. JSW/JSPL/SHYAM/SRMB/BMASL/ELECROSTEEL/SSL |
| 26 | (b)Add extra over the rate of ground floor/initial 4 m for each basement floor and each additional floor below/ above ground floori) Up to 4 th floor roof in each addl. Floor1 st Floor |
| 27 | 2 nd Floor |
| 28 | Welding in M.S. structural work with gas or electric:b) Continuous weld. |
| 29 | Brick work with 1st class bricks in cement mortar (1:4)(b) In superstructure, ground floor |
| 30 | Add extra for basement and each additional floor over the rate for ground floor on Item No. 22.02(a) Up to 4th floor2nd Floor |
| 31 | 125 mm. thick brick work with 1st class bricks in cement mortar (1:4) in ground floor. |
| 32 | Add extra for each additional floor over the rate for ground floor on items sl no. 24(a) up to 4th floor2 nd Floor |
| 33 | Supplying, fitting & fixing 1st quality Ceramic tiles in walls and floors to match with the existing work & 4 nos. of key stones (10mm) fixed with araldite at the back of each tile & finishing the joints with white cement mixed with colouring oxide if required to match the colour of tiles including roughening of concrete surface, if necessary or by synthetic adhesive & grout materials etc . (A) Floor With Sand Cement Mortar (1:4) 20 mm thick & 2 mm thick cement slurry at back side of tiles using cement @ 2.91 Kg/Sq.m & joint filling using white cement slurry @ 0.20kg/Sq.m. (a) Area of each tile upto 0.09 Sq.m ii) Other than Coloured decorative including white |
| 34 | Removing old scales, blisters etc. of interior surface of walls, ceiling by scraping etc. and preparing smooth and even surface with rendering or cement mortar (1:2) (as necessary), to make the surface suitable for receiving distemper. (Payment against this item will be made only when this has been done on the specific direction of the Engineer-in-charge). |
| 35 | Applying Exterior grade Acrylic primer of approved quality and brand on plastered or cencrete surface old or new surface to receive decorative textured (matt finish) or smooth finish acrylic exterior emulsion paint including scraping and preparing the surface throughly, complete as per manufacturer's specification and as per direction of the EIC. In Ground Floor: (a) One Coat |
| 36 | (A) Painting with best quality synthetic enamel paint of approved make and brand including smoothening surface by sand papering etc. including using of approved putty etc. on the surface, if necessary :(a) On timber or plastered surface :With other than hi-gloss of approved quality-(iv) Two coats (with any shade except white) |
| 37 | (b) On steel or other metal surface :With other than hi-gloss of approved quality-(iv) Two coats (with any shade except white) |
| 38 | (b) Priming one coat on timber or plastered surface with synthetic oil bound primer of approved quality including smoothening surfaces by sand papering etc. |
| 39 | a) Priming one coat on steel or other metal surface with synthetic oil bound primer of approved quality including smoothening surfaces by sand papering etc. |
| 40 | Wood work in door and window frame fitted and fixed in position complete including a protective coat of painting at the contact surface of the frame excluding cost of concrete, Iron Butt Hinges and M.S clamps. (The quantum should be corrected up to three decimals).(d) Sal : Local. |
| 41 | Labour for taking out door and window frame including shutter for repair or replacement of different parts of the frame & refixing the same including mending good all damages complete. (Concrete and brick work for mending damage will be paid separately)(a) Up to area 2.5 Sq.m |
| 42 | Panel shutters of door and window, as per design (each panel consisting of single plank without joint), including fitting and fixing the same in position but excluding the cost of hinge and other fittings.In ground floor.(iii) 35mm thick shutters with 19mm thick panel of size 30 to 45 cm.(b) Sishu, Gamar, Champ,Badam,Bhola, Mogra, Hallak. |
| 43 | Supplying, fitting and fixing M.S. clamps for door and window frame made of flat bent bar, end bifurcated with necessary screws etc. by cement concrete(1:2:4) as per direction. (Cost of concrete will be paid separately)c) 40mm X 6mm, 125mm Length |
| 44 | Iron butt hinges of approved quality fitted and fixed with steel screws, with ISI mark.(vi) 100mm. X 50mm. X 1.25mm. |
| 45 | Iron socket bolt of approved quality fitted and fixed complete.c) 150mm long x 10mm dia bolt. |
| 46 | (e) 300mm long x 10mm dia bolt. |
| 47 | i) Iron hasp bolt of approved quality fitted and fixed complete (oxidized) with 16mm dia rod with centre bolt and round fitting.(c) 300mm long. |
| 48 | (A) Iron door ring of approved quality fitted and fixed with nut and washercomplete.(i) 50mm dia. |
| 49 | (a) Metallic magic eye of approved quality fitted and fixed complete. |
| 50 | Supplying, Fitting & Fixing Factory made P.V.C. door frame of size 50 mmx47 mm with a wall thickness of 5 mm, made out of extruded 5 mm, PVC sheet miter cut at two corners and joined with two Nos of 1.5 mm long brackets of 15 mm x15 mm M.S. square tube. The two vertical door profiles are to be reinforced with 19 mix 19 mm M.S. Square tube of 19 gauge, weather seal to be provided through out the frame. The door frame shall be fixed with the wall using 65/100 mm long M.S. Screws through the frame by using P.V.C fasteners. A minimum of 4 Nos of screws to be provided for each vertical member and minimum 2 Nexfor horizontal member etc. complete as per Manufacturer's specification and direction of Engineer-in-Charge. |
| 51 | 35 mm thick factory made Solid panel PVC Door shutter made out of single piece extruded solid PVC profiles, 5 mm (± 0.2mm) thick, having styles & rails (except lock rail) of size 95 mm x 35 mm x 5 mm, out of which 75 mm shall be flat and 20 mm shall be tapered (on both side), having one side thickness of 15 mm integrally extruded on the hinge side of the profile for better screw holding power, including reinforcing with MS tube of size 40 mm X 20 mm x 1 mm, joints of styles & rails to be mitered cut & joint with the help of PVC solvent cement, self driven self tapping screws & M.S. rectangular pipes bracket of size 190 mm X 100 mm of cross section size 35 mm x 17 mm x 1 mm at each corner. Single piece extruded 5mm thick solid PVC Lock rail of size 115 mm x 35 mm x 35 mm, out of which 95 mm to be flat and 20 mm to be tapered at both ends, having 15 mm solid core in middle of rail section integrally extruded, fixing the styles & rails with the help of solvent and self driven self tapping screws of 125 mm x 8 mm, including providing 5 mm Single piece solid PVC extruded sheet inserted in the door as panel, all complete as per manufacturer's specification and direction of Engineer-in-charge.a) Factory made Single piece Nosn decorative extruded PVC tapered profiles door shutter(mat / plain finish) |
| 52 | Supplying, fitting and fixing windows and ventilators with or without integrated grills conforming to IS 1038-1975 and manufactured from rolled steel sections conforming to IS 7452-1974 with Nosn-friction projecting type, box type hinges, glazing clips, lugs locking bracket, handle plate etc, including hoisting in position, straightening ifrequired, fixing lugs in cement concrete ( 1:2:4) with stone chips 20 mm down cutting holes and mending good damages to match with existing surface complete in all respect excluding glazing.In Ground floor(b) Open able steel windows as per IS sizes with side hung shutters and horizontal glazing bars. [The extra rate admissible for the open able portion only](b) Open able steel windows as per IS sizes with side hung shutters and horizontal glazing bars. [The extra rate admissible for the open able portion only] |
| 53 | (c ) Extra over Item No. 37.01(ii) Top hung side hung ventilators as per I.S. sizes 580 mm. |
| 54 | (vi) steel peg stay 300 mm long including fitting and fixing. |
| 55 | (viii) M.S. integrated grill as per approved design integrated with steel window or ventilator, joints continuously welded with M.S. flats and bars. |
| 56 | Supplying best Indian sheet glass panes set in putty and fitted and fixed with nails and putty complete. (In all floors for internal wall & up to 6 m height for external wall)(i) 3 mm thick (weighing 7.4 kg/Sq.m) |
| 57 | Renewing worn out putty of glass panes :(a) Panes Nost exceeding 0.2 Sq.m |
| 58 | Mazdoor (Male) for shifting household goods and to perform other activities as and when necessary as per direction of the EIC |
| 59 | Anti-termite treatment to the outside of foundation with chemical emulsion by admixing chloropyrofos emulsifiable concentrate (1% concentration) with water by weight, drilling 12mm. dia holes in concrete or masonry apron at an interval of 300mm. to a depth, of 300mm or more as close to the plinth wall as possible and the chemical emulsion pumped into those holes to soak the soil below at a rate of 2.25 litres per linear metre complete as per specification laid down in para 4.3.1.1 of Code I.S.-6313 (Part-III)-1981. |
| 60 | (c) Anti-termite treatment to the soil under floor with chemical emulsion by admixing chloropyrofos emulsifiable concentrate (1% concentration) with water by weight including drilling vertically 12mm. dia holes at the junction of floor and wall at 300mm. interval to reach the soil below using hand operated pressure pump to squirt chemical emulsion into the pump to squirt chemical emulsion into the holes at the rate of one litre per hole. The holes shall be sealed after operation to match with the existing floor. The entire work is to be carried out as per specification laid down in para 4.3.1.4 of code I.S.-6313 (Part-III)-1981. |
| 61 | Supplying, fitting & fixing 1st quality Ceramic tiles in walls and floors to match with the existing work & 4 nos. of key stones (10mm) fixed with araldite at the back of each tile & finishing the joints with white cement mixed with colouring oxide if required to match the colour of tiles including roughening of concrete surface, if necessary or by synthetic adhesive & grout materials etc . (B) WallWith Sand Cement Mortar (1:3) 15 mm thick & 2 mm thick cement slurry at back side of tiles using cement @ 2.91 Kg/Sq.m & joint filling using white cement slurry @ 0.20kg/Sq.m.(a) Area of each tile upto 0.09 Sq.m(i) Coloured decorative |
| 62 | Taking out door shutter and rehanging the same by fixing aluminium sheet [0.457mm] with proper nail etc. |
| 63 | Labour for dismantling G.I. pipe with fittings.(i) 15 mm |
| 64 | Supplying, fitting and fixing G.I. pipes of TATA make with all necessary accessories, specials viz. socket, bend, tee, union, cross, elbow, nipple, long screw, reducing socket, reducing tee, short piece etc. fitted with holder bats clamps, including cutting pipes, making threads, fitting, fixing etc. complete in all respect including cost of all necessary fittings as required, jointing materials and two coats of painting with approved paint in any position above ground. (Payment will be made on the centre line measurements of total pipe line including all specials. Nos separate payment will be made for accessories, specials. Payment for painting will be made separately)(B) For Concealed Work(a) 15 mm dia. medium quality |
| 65 | Supplying, fitting and fixing shower of approved brand and make.(g) PTMT overhead shower ( Prayag or equivalent)(i) 75 mm round |
| 66 | Supplying, fitting and fixing bib cock or stop cock.(a) (i) Chromium plated Bib Cock short body (Equivalent to Code No. 511 & Model - Tropical / Sumthing Special of ESSCO or similar brand) |
| 67 | Supplying, fitting and fixing Flat back urinal (half stall urinal) in white vitreous chinaware of approved make in position with brass screws on 75 mm X 75 mm X 75 mm wooden blocks complete (i) 635 mm X 395 mm X 420 mm |
| 68 | Supplying, fitting and fixing white vitreous china best quality approved make wash basin with C.I. brackets on 75 mm X 75 mm wooden blocks, C.P. waste fittings of 32 mm dia., one approved quality brass C.P. pillar cock of 15 mm dia., C.P. chain with rubber plug of 30 mm dia., approved quality P.V.C. waste pipe with C.P. nut 32 mm dia., 900 mm long approved quality P.V.C. connection pipe with heavy brass C.P. nut including mending good all damages and painting the brackets with two coats of approved paint.(ii) 550 mm X 400 mm size |
| 69 | Dismantling E.P. or Anglo-Indian W.C. |
| 70 | Supply of UPVC pipes (B Type) & fittings conforming to IS-13592-1992(A) (i) Single Socketed 3 Meter Length(b) 110 mm |
| 71 | (ii) Double Socketed 3 Meter Length(b) 110 mm |
| 72 | (vii) Double Socketed 0.60 Meter Length(b) 110 mm |
| 73 | Supply of UPVC pipes (B Type) & fittings conforming to IS-13592-1992(B) Fittings(iii) Door Tee(b) 110 mm |
| 74 | ix) Bend 45º(b) 110 mm |
| 75 | xi) Door Bend (T.S.)(b) 110 mm |
| 76 | xiv) Cross Tee with Door(b) 110 mm |
| 77 | xxi) 110 X 110 P Trap75 mm |
| 78 | xv) Vent Cowl(b) 110 mm |
| 79 | xvi) Pipe Clip(b) 110 mm |
| 80 | xvii) W.C. Connector (150 mm long) 125 X 110(W/WC Ring)75 mm |
| 81 | xIv) Round Jali75 mm |
| 82 | L) Rubber Ring(b) 110 mm |
| 83 | Labour for fitting and fixing U.P.V.C. pipes for above ground work including cost of jointing materials etc. fitting and fixing all necessary specials, cutting pipes, cutting holes in walls or R.C. floor where necessary and mending good all damages excluding the cost of masonry or concrete work, if necessary, but including the cost and fitting and fixing holder bat clamps (any floor) or for underground work including cutting trenches up to 1.5 metre and refilling the same complete as per direction of the Engineer-in-charge. (Payment will be made on centre line measurement of the total pipeline including specials.(A)Above ground(ii) 110 mm dia. |
| 84 | Dismantling H.C.I. pipe with fittings including melting lead caulked joints.(iii) 100 mm |
| 85 | Supplying, fitting and fixing Orissa pattern water closet in white glazed vitreous chinaware of approved make in position complete excluding 'P' or 'S' trap (excluding cost of concrete for fixing).(i) 580 mm X 440 mm |
| 86 | Supplying, fitting and fixing E.W.C. in white glazed vitreous chinaware of approved make complete in position with necessary bolts, nuts etc.(a) With 'P' trap |
| 87 | Supplying, fitting and fixing towel rail with two brackets.(a) C.P. over brass(ii) 25 mm dia. and 600 mm long |
| 88 | Supplying, fitting and fixing in position R.C.C. Manhole/ pit cover of approved make with rim of approved make (Heavy type)(i) 450 mm dia. |
| 89 | Supplying, fitting and fixing 10 litre P.V.C. low-down cistern conforming to I.S. specification with P.V.C. fittings complete,C.I. brackets including two coats of painting to bracket etc. |
| 90 | Supplying, fitting and fixing best quality Indian make mirror 5.5 mm thick with silvering as per I.S.I. specifications supported on fibre glass frame of any colour, frame size 550 mm X 400 mm |
| 91 | Supplying, fitting and fixing urinal flush pipe fittings of approved brand.(a) C.P. urinal flush pipe fittings range of one i) C. P. Flush Pipe(b) C.P. urinal flush pipe fittings range of two |
| 92 | Supplying,fitting and fixing 32 mm dia. Flush Pipe of approved make withnecessary fixing materials and clamps complete.ii) C. P. Flush Pipe Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Sep 26, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedOct 12, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 6 daysOct 13, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 7 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender