Tender For special Repair To Toilets (7 Nos) Bldg No P-10, P-11, P-12, P-13, P-14, P-15 & P-16 And Provn Of Internal Wiring Of Drone Lab At Rudra Training At Pms Under Ge Panagarh
Tender Value
38.83 Lakhs
Estimated cost
Bid Submission
16 Oct 2026
13 days left
EMD
77700
Bank guarantee accepted
Document Fee
500
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Purba Bardhaman → West Bengal
EMD Exemption
Not Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for special Repair To Toilets (7 Nos) Bldg No P-10, P-11, P-12, P-13, P-14, P-15 & P-16 And Provn Of Internal Wiring Of Drone Lab At Rudra Training At Pms Under Ge Panagarh
BOQ
| Sl. No. | Item Description |
| 1 | Demolition of cement concrete (un reinforced) in ground floors and paving n.exc 15cm thickness (below or above ground (level) and lowering if necessary, removal of the rubbish off the premises complete all as specified and directed. |
| 2 | Demolition of brick work built in CM including all quions, arches, pillars etc, but excluding ashlar facings, dressed stonework and precast concrete articles including removal of the rubbish off the premises complete all as specified and directed. |
| 3 | Demolition of reinforced cement concrete in ground floors and pavings n.exc 15 cm thickness (below or above ground level) and removal of the rubbish off the premises complete all as specified and directed. |
| 4 | M&L for brick work with fly ash bricks old size, straight or curved on plan exc 6m mean radius, built in cement mortar 1:6 complete all as specified and directed. |
| 5 | M&L for brick work with fly ash bricks old size, straight or curved on plan exc 6m mean radius, in half brick walls built in cement mortar 1:4 complete all as specified and directed. |
| 6 | Taking down cement plaster on brick or stone wall etc. including racking out joints hacking for key scrubbing down with water etc complete all as specified and as directed. |
| 7 | M&L for Rendering 15 mm thick cement plaster in CM 1:4 on fair faces of brick/concrete surfaces finished fair and even, mixed wth water proofing compound admixture (if directed) as per manufacturer's instruction, complete all as specified and directed.Note :- WPC will measuered and paid separatly under relevant item of schedule. |
| 8 | Supply only WPC, complete all as specified and as directed. |
| 9 | Material & labour preparation of newly plastered surfaces of wall and applying Two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over new surfaces on external surface including putty over plastered surface to prepare the surface even and smooth as directed by Engineer-in-charge |
| 10 | M&L for rendering 15 mm thick on other than fair faces of brick work or concrete surfaces, finished fair and even on walls in cement mortar (1:6), complete all as specified. |
| 11 | Material & Labour for preparation of new surfaces of plastered walls and applying Two coats of Distempering with 1st quality acrylic distemper (ready mixed) having VOC content less than 50 gms/litre, of approved manufacturer, of required shade and colour complete, as per manufacturer's specification. over and including a coat of primer over plastered surfaces of walls complete all as specified. |
| 12 | M&L for rendering 5mm thick on fair faces of ceiling / chajja concrete surfaces in cement mortar 1:3 complete all as specified & directed. |
| 13 | M&L for prepartion of newly plastered ceiling/chajja surfaces and applying three coat of white wash complete all as specified and directed. |
| 14 | Taking down chowkat or frames exc 1.5 sqm but n exc 4.0 sqm each with shutter (without taking off shutters from the frame) and removing to or from store complete all as specified and as directed. |
| 15 | Taking down Chowkats or frames not exc. 1.5 sq. m each with shutters (without taking off shutters from the frames) and removing to or from store complete all as specified and as directed. |
| 16 | S&F solid PVC door frame of size 50mmx47mm made out of 5mm plain colour PVC sheet reinforced with MS square tube, supplying and fixing in opening as per specification and drawing complete all as specified and directed. |
| 17 | S&F Factory made solid panel PVC door shutter 30mm thick (style) consisting of frame made out of MS tubes for top and bottom rails. MS frame shall be covered with heat moulded plain colour PVC 'C' channel having a PVC sheet trip of 20mm with stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail and bottom rail; panelling of plain colour PVC sheet to be fitted in the MS frame welded/sealed to the stiles and rails with suitable PVC sheet beading and joined together with solvent cement, supplying and fixing in the frame at site as per specification and drawing complete all as specified and directed. |
| 18 | S&F Powder coated aluminium (minimum thickness of powder coating 50 micron) work for doors, windows, ventilators frame and partitions (Fixed portions) with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS:1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing/ paneling, C.P. brass/ stainless steel screws, all complete as per the directions of Engineer-in-Charge |
| 19 | S&F Powder coated aluminium (minimum thickness of powder coating 50 micron) for shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber/neoprene gasket required (Fittings shall be paid for separately) with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS:1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing/ paneling, C.P. brass/ stainless steel screws all complete as per architectural drawings and the directions of Engineer-in-chargeher for openable/sliding shuttters) including all necessary fittings as directed |
| 20 | S&F 100 mm butt hinges,extruded aluminium alloy with galvanised mild steel hinge pin, anodised and fixed, type B-22,complete all as specified and directed. |
| 21 | S&F aluminium anodised 150 mm barrel tower bolts of extruded section complete all as specified and directed. |
| 22 | S&F 150 mm long extruded aluminium alloy handles,fabricated type, anodised complete all as specified and directed. |
| 23 | S&F Stainless steel wire cloth 0.36 mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples, complete all as specified and directed. |
| 24 | M&L for 4mm thick figured glass, pin head type and glazing with oil putty in square n. exc 0.5 sqm in each pan all as directed |
| 25 | M&L for 4mm thick,ordinary quality and glazing with oil putty in square exc 0.5 sqm in each pan all as directed |
| 26 | M&L for 100 mm thick cement concrete Type B-1, 1:2:4 (using 20 mm graded stone aggregate) as in sub bases with nominal reinforcement complete all as specified and directed |
| 27 | M&L Mild steel TMT bars 6mm to 8 mm dia, cut to length, bent to shape required, including cranking, bending pirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed. |
| 28 | Dismantling of floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises complete all as specified and directed. |
| 29 | M&L Non Skid ceramic coloured tiles 7 to 8mm thick (squares/rectangular) area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm, in floors/skirting etc. laid over 15mm thick 1:6 cement mortar screed bed set and jointed in neat cement slurry and pointed in white or coloured cement to match complete all as specified and directed. |
| 30 | M&L for Glazed ceramic tiles in vertical surface 350x 250x 7 mm/ 450X 350X 7mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match over and including 15mm thick screed bed in CM 1:3. |
| 31 | S&F Chimney bars (straight or camber); bearing bars; tongues or water bars for window frames; window guard bars, plain, let in and fixed independently in wooden frames, L or T section supports for shelves etc. and similar articles conforming to Fe-290 Gde E-165 conforming to Fe-290, Gde-E-165 the grill shall be inseted in the wall surface including necessary drilling and grouting with cement etc, complete all as specified and directed. |
| 32 | S&F Framed work such as grills, gratings, etc with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe-290, Gde-E-165 the grill shall be inseted in the wall surface including necessary drilling and grouting with cement etc, complete all as specified and directed. |
| 33 | Dismanting of wrought iron or mild steel work af any description not otherwise provided for complete all as specified and as directed by Engineer-in-charge |
| 34 | M&L for preparing of new steel & iron surfaces of any description, not otherwise described, over 10cm width or girth and applying two coats of synthetic enameled paint over a coat of Red oxide zinc chrome primer zinc chrome complete all as specified and as directed. |
| 35 | M&L for RCC 1:1.5:3 type A1 (20 mm graded crushed stone aggregate) nominal mix as in chajja complete all as specified and directed. |
| 36 | M&L for RCC 1:1.5:3 type A1 (20 mm graded crushed stone aggregate) nominal mix as in slab supported on wall complete all as specified and directed. |
| 37 | M&L for use and waste of fair finish formwork to sides of chullah hoods, chajjas complete all as specified and directed. |
| 38 | M&L for RCC 1:1.5:3 type A1 (20 mm graded crushed stone aggregate) nominal mix as in Fins, fascias, louvres, parapets, and railings exc. 60cm in height, newels, balustrade, and the like complete all as specified and directed. |
| 39 | M&L for use and waste of fair finish formwork for sofits of slab complete all as specified and directed. |
| 40 | M&L for RCC (1:1.5:3) type A1 (nominal mix)(using 20mm graded crushed stone aggregate) coloumn, pillars, piers, posts and struts complete all as spd and directed |
| 41 | M&L for RCC 1:1.5:3 type A1 (20 mm graded crushed stone aggregate) nominal mix in beams, cantilevers, bressummers, lintels over1.5 m span complete all as specified and directed |
| 42 | M&L for use and waste of fair finish formwork for coloums complete all as specified and directed. |
| 43 | M&L for use and waste of formwork for sides and sofits of beams and lintels complete all as specified and directed. |
| 44 | M&L Mild steel TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending pirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed. |
| 45 | M&L Mild steel TMT bars 5mm dia and over upto and including 10mm dia in stirrups , spacers and binders, cut to length, bent to shape required, including cranking, bending pirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed. |
| 46 | M&L for use and waste of fair finish Formwork to edges of concrete flats, treads, breaks in floors, window cills, concrete railings, openings in concrete walls, floor and roofs n exc 20 cm wide and sides of RCC/ PCC bands in walls, horizontal or sloping and similar work exc 10cm but n exc 20cm wide complete all as specified and directed. |
| 47 | M&L for prepartion of old surface and applying two coats of Super Latex (Sika or equivalent) @ 80gm per sqm per coat in the ratio of 1:1.5:5 (latex : water : cement) over internal/external of brick/concrete surface after cleaning and washing the surface by wire brush and plenty of water The entire surface shall be washed throughly with plenty of water and then allowed to dry complete all as specified and as directed. Note:- The entire process to be executed through authorised applicator. |
| 48 | M&L Machine Cut Kota Stone Slab 18-20mm thick as in Floor, etc. over and including Screed Bed or Bedding Layer 20mm thick in Cement Mortar (1:6), Laid and Jointed with Grey Cement Slurry mixed with Pigment to match the Shade of the Slab including Rubbing and Polishing, complete all as specified and as directed. |
| 49 | M&L for Kota stone slab 18-20 mm thick in riser steps skirting dado and pillar laid over cement screed 15 mm thick CM 1:3 and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and mirror polishing complete all as specified and as directed |
| 50 | M&L for Green marble work 15 mm thick (table rubbed and polished) in steps, jambs, pillars, window cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with marble shade of following typesnt with admixture of pigment to match the shade of granite stone including grinding and polishing complete over and including 15mm thick Screed bed or backing coat for laying floor finishes in CM 1:6 complete all as specified. |
| 51 | M&L for 75 mm thick cement concrete M10 (Nominal Mix) with 40mm graded crushed aggregate finished even and fair laid to a slope of 1 in 12, laid in alternate bays, each bay not exceeding 3 m length with joint filled with bituminous mastic filling comprising a mixture of 1 part of heated Industrial bitumen 85/25 grade and two parts of heated sand as in plinth protection complete all as specified |
| 52 | M&L Plain Cement Concrete 1:3:6 type C1 (using 20 mm stone aggregate) as in surface channels and drains, complete all as specified and directed. |
| 53 | S&F in repairs Gun metal, globe or gate valve with iron wheel head, 20 mm bore, screwed both ends for pipe complete all as specified and as directed. |
| 54 | S&F in repair CP Bib taps 15mm dia, with cfancy handle, screwed down, screwed for iron pipe or for brass ferrule, fency type and fixed complete all as specified and directed. |
| 55 | S&F in repair Stop valve cast copper alloy screwed down high pressure with capston headed handle chromium plated concealed type screwed both ends for pipe 15 mm bore or for unions complete all as specified and as directed. |
| 56 | S&F in repaie fancy,chromium plated Stop valves 15mm dia, cast copper alloy, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed complete all as specified and as directed. |
| 57 | S&F in repair angle cock 15 mm bore fancy type chromium plated, with capstan head, high pressure, screwed down, screwed for iron pipe or for brass ferrule fixed to iron pipe complete all as specified and as directed. |
| 58 | S&F in repair 15mm bore pillar taps cast copper alloy,with capstan heads,chromium plated,screwed down, fancy type high pressure, with or without lettred 'HOT orCOLD' with long screwed sunk and fly nuts complete all as specified and directed. |
| 59 | Supply & Fixing in repairs Vitreous China Ware Wash hand basin white flat back size 550mmx400mm without pedestal, cutting for and pinning ends of brackets or erecting stand including necessary PVC outlet pipe, CP coupling 32mm dia complete all as specified complete all as specified |
| 60 | S&F in repair soap dish, any type fixed to plugs chromium plated brass screws complete all as specified and as directed. |
| 61 | S&F in repair glass self assembly consisting of 5.5 mm thick glass sheet glass self 12 Cm wide with CP bracket gaurd and railing 60 Cm long complete all as specified and as directed. |
| 62 | S&F in repair chromiuim plated Swivel shower roses with shower arm, 125 mm size including fxing to steel pipe or union etc complete all as specified and as directed. |
| 63 | S & F in repairs vitreous china squatting pan, 'Orissa\\" pattern, size 580 mm X 440 mm white with ‘P’ or ‘S” trap, front or back inlet and integral foot rests, any pattern and including fixing , connector to flush pipe, lime concrete bedding and making connections to flush pipe, connector to branch pipe and anti syphonage pipes etc. including sealing the joints and making leak proof using sealant complete all as specified and as directed by Engineer-in-Charge. |
| 64 | S&F in repairs PVC valveless,syphonic action type, low level PVC flushing cistren 10 ltr cap white with flush pipe & all fitting complete all as specified. |
| 65 | S&F in repair Vitreous china urinal, half stall type, white (excluding flushing cistern, flush pipe) including urinal spreader of PTMT any colour for fixing with 15mm dia pipe. (Minimum weight 60gms) and including waste pipe complete all as specified and directed. |
| 66 | S&F PVC connections 15 mm size with PTMT nuts of length 600mm complete all as specified and as directed. |
| 67 | S&F in repairs 32mm dia Waste coupling, brass , chromium plated for glazed ware , basins , etc. with long screwed shanks and fly -nuts , flange end bedded in red lead cement and other end fixed complete all as specified and as directed. |
| 68 | S&F in repairs grating square, Grating doom 125 mm dia with waste hole of PTMT. (Minimum weight 40gms), complete all as specified and directed. |
| 69 | Taking up or down steel water tubings and fittings etc complete and making good disturbed surfaces of walls/ceilings etc for 15 mm bore pipe complete including stacking aside for reuse and removal of unserviceable items from site complete. |
| 70 | Taking up or down steel water tubings and fittings etc complete and making good disturbed surfaces of walls/ceilings etc for 20 mm bore pipe complete including stacking aside for reuse and removal of unserviceable items from site complete. |
| 71 | S&F 16 mm outer dia medium grade CPVC, SDR 11 & plain CPVC SDR 11 with all fittings (brass inside the fittings) and fixed complete to walls and ceiling or laid in floors complete all as specified and directed. |
| 72 | S&F 20 mm outer dia medium grade CPVC, SDR 11 & plain CPVC SDR 11 with all fittings (brass inside the fittings) and fixed complete to walls and ceiling or laid in floors complete all as specified and directed. |
| 73 | S&F in repairTubular towel rail, 20mm dia, D type, brass chromium plated, 60cm long between flanges complete all as specified and directed. |
| 74 | Supply & fix mirror 600mmx 400mm bevelled edge mirror of selected quality glass, mounted on 6 mm thick AC building board or commercial plywood and fixed to wooden plugs with chromium plated brass screws and cup washers complete all as specified and directed. |
| 75 | S&F PVC plain bend (any radius) for 75 mm bore, PVC pipes, complete all as specified and directed. |
| 76 | S&F 75mm bore PVC (SWR) junction single, (single T) equal or unequal fitted with oval access door, complete all as specified and directed. |
| 77 | S&F 75 mm bore PVC (SWR) pipes, type B single socketed in any length with rubber ring joints fixed to walls including dismantling old unserviceable existing pipe with fittings, complete all as specified and directed.[Note : Payment shall be made in net length as fixed between the fittings as per SSR Part-II preamble para (a) of Page 384.] |
| 78 | S&F 110 mm bore PVC (SWR) pipes, type B single socketed in any length with rubber ring joints fixed to walls including dismantling old unserviceable existing pipe with fittings, complete all as specified and directed. |
| 79 | S&F PVC (SWR) bends, plain, 110 mm bore any radius, complete all as specified and directed. |
| 80 | S&F 110 mm bore PVC (SWR) junction single (single T) equal or unequal fitted with oval access door, complete all as specified and directed. |
| 81 | Supply and fixing as in repair 110mm dia PVC(SWR) pipe, type B fixed to wall or laid in trenches or in floors etc, including demolition complete all as specified and directed. |
| 82 | S&F in repair PVC door bends with oval access door (any radius) for 75 mm bore PVC pipes, complete all as specified and as directed. |
| 83 | S&F in repair PVC door bends with oval access door (any radius) for 75 mm bore PVC pipes, complete all as specified and as directed. |
| 84 | Cutting chases in brick walls, pinning in, making good to facings where required and pointing in cement mortar 1:3 and cutting chases for concealed water tubing and making good of groves for concealed GI/PVC tube, cutting not exc 10cm girth complete all as specified and as directed. |
| 85 | Rounding to edges of stone slabs one edge, such as in steps, cooking platform, granite/kota stone and other similar situations incl polishing, complete all as specified and directed. |
| 86 | M&L for repair to crack portion with jacktting technique, taking down existing plaster upto brick wall surface of min 200 mm wide, cleaning to loose particles on surface of brick work along the length of crack and filling the gap/ crack area with PCC 1:1.5:3 type A0 using 12.5mm aggregate both side of the wall surface fixed with, drilling holes 10mm dia on either side of the crack by means of drilling machine through out the full width of the wall @25 cm c/c and insert 8/10 mm dia od in the drilled holes, welded with horizontal rod to with hold the welded mesh and applying grit plaster 1:1:2 using 4 mm and down aggregate finished even and smooth without using extra cement, complete all as specified and directed. (Note: Reinforcement and welded mesh will be measured and paid separately) |
| 87 | M&L for grading roof in cement mortar 1:3, 25mm thick in edge and 50mm thick in ridge including necessary curing complete all as specified in SSR Part I clause No 11.42.2 |
| 88 | M & L for providing water proofing treatment with a layer of APP based polymeric membrane, 3 mm thick (minimum), weighing not less than 3.60 kg/Sqm reinforced with polymer non woven fabric (weighing not less than 160 gm/ Sqm) shall be applied over one coat of cold bituminious primer @ 0.40 ltr/ Sqm ( membrane shall be laid using butane torch and sealing all joints etc, complete all as specified and directed .( Note: The overlaps shall be of minimum 75 mm on longitudinal direction and 100 mm on transverse direction) complete all as specified and directed. |
| 89 | M&L for one coat aluminium paint over APP membrane, over 10cm in width or girth,not otherwise described complete all as specified. |
| 90 | Taking down carefully aluminium/Copper conductor point wiring (light , fan, socket or powr) complete including fittings such as switches, ceiling rose, pendents, regulators sockets etc and removing (except those to be reused shall be kept in safe custody at the site) and making good disturbed surfaces of walls, floors etc tomatch with the existing completeall as specified and directed. Please Enable Macros to View BoQ information |
| 91 | Taking down carefully aluminium/Copper conductor point wiring (light , fan, socket or powr) complete including fittings such as switches, ceiling rose, pendents, regulators sockets etc and removing (except those to be reused shall be kept in safe custody at the site) and making good disturbed surfaces of walls, floors etc tomatch with the existing completeall as specified and directed. Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Sep 26, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedOct 16, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 13 daysOct 17, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 14 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender