Tender For Addition/ Alteration To Improvement Of Bldg No-P-14 At Panchu Tikrey, Hut Bay
Tender Value
43.60 Lakhs
Estimated cost
Bid Submission
16 Oct 2026
20 days left
EMD
87200
Bank guarantee accepted
Document Fee
500
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
South Andamans → Andaman And Nicobar Islands
EMD Exemption
Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for Addition/ Alteration To Improvement Of Bldg No-P-14 At Panchu Tikrey, Hut Bay
BOQ
| Sl. No. | Item Description |
| 1 | NOTE: 1. The bidders/ contractors are advised to read tender documents and all corrigendum/ amendments and General conditions of contracts before entry/ quoting the rates. |
| 2 | Demolition of cement concrete (unreinforced) of any description and in any position not otherwise specifically provided for) complete all as specified and directed |
| 3 | M&L for PCC 1:4:8 Type D-2 (using 40mm graded stone aggregate) as in sub base finished to receive floor treatment etc complete all as directed. |
| 4 | Dismantling hearth or wall tiling of any description, size and thickness including cement mortar bedding , removing rubbish off the premises etc complete all as directed. |
| 5 | M&L for Vitrified tiles Double Charged 10mm thick (square/ rectangular) polished, area of each tiles not exceeding 0.42 sqm but not exceeding 1.00 sqm, in floors including screed bed 15mm thick in Cm 1:6 etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match |
| 6 | M&L for Vitrified tiles Double Charged tiles in vertical surface 10mm thick tiles exceeding 0.42 sqm but not exceeding 1.00 sqm fixed on vertical surfaces such as skirting /dado etc, set and jointed in neat cement slurry over 10mm thick backing coat in CM (1:4) and pointed in coloured cement to match complete all as specified and directed. |
| 7 | M&L for Vitrified tiles light shad 10mm thick (square/ rectangular) polished, area of each tiles not exceeding 0.36 sqm , in floors including screed bed 15mm thick in CM 1:6 etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match |
| 8 | M&L for Vitrified tiles, light shade, 10mm thick, in vertical surface area of each tiles not exceeding 0.36 sqm on vertical surfaces such as skirting /dado etc, set and jointed in neat cement slurry over 10mm thick backing coat in CM (1:4) and pointed in coloured cement to match complete all as specified and directed. |
| 9 | M&L Non Skid Ceramic tiles 7 to 8mm thick (square/ rectangular/strip) polished, area of each tiles not exceeding 0.18 sqm but not exceeding 0.36 sqm, in floors including screed bed 15mm thick in Cm 1:6 etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match |
| 10 | M&L for Glazed ceramic tiles in vertical surface each tiles of size 300x600mm, 7-8mm thick (coloured) of superior quality with highlighter tiles fixed on vertical surfaces such as skirting /dado etc, set and jointed in neat cement slurry over 10mm thick backing coat in CM (1:4) and pointed in coloured cement to match complete all as specified and directed. |
| 11 | Demolition of stone slabs, paving stones and tiles of any description and thickness in floors, aprons, laid, bedded and pointed in any mortar complete all as specified and directed. |
| 12 | M&L for Z black Granite (of any type) 18-20mm thick (table rubbed and polished) in steps, jambs, pillars, window- cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite. including 15mm thick screed bed in CM (1:6), complete all as specified and as directed. |
| 13 | M & L for 15mm thick Artficial Granite ( any type/colour as approved by GE) work in steps, jambs, pillars, window- cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite. including 15mm thick screed bed in CM (1:6), for laying floor finishes complete all as specified. |
| 14 | Rounding to edges of stone slabs one edge, such as in steps, cooking platform, and other similar situations complete all as specified and as directed. |
| 15 | Demolition of brick work / stone boulders/block masonry built in cement mortar incl all Quoins , arches, pillars etc but excluding ashlar facings, dressed stone work and precast concrete articles complete all as specified and directed. |
| 16 | M&L for Pre-cast cement concrete block masonry with solid blocks, exc. 10 cm in width and setting in mortar, complete built in CM (1:6) complete all as specified and as directed. |
| 17 | All as per item No.15 above but except bricks. |
| 18 | Taking down cement plaster any description on brick or stone walls etc including racking out joints hacking for key scrubbing down with water etc complete all as specified and directed. |
| 19 | M&L for Rendering in 10 mm thick in CM 1:6 fair faces of block work/concrete surface of any description in wall etc finished surfaces even and smooth finish complete all as specifed and directed. |
| 20 | M&L for Rendering in 10 mm thick in CM 1:4 fair faces of block work/concrete surface of any description in wall etc finished surfaces even and smooth with sogol finish complete all as specifed and directed. |
| 21 | M&L for preparation of newly plaster surface of walls and applying Two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over new surfaces including preparation of surfaces. |
| 22 | M&L for preparation of of newly plastered surfaces of walls and applying two coat of oil bound distemper over 2mm thick wall care putty and one coat of primer on wall, complete all as specified and as directed. |
| 23 | M&L for complete removal of existing treatment from old plastered surfaces of wall and applying two coat of oil bound distemper on walls over 2mm thick wall care putty and one coat of primer, complete all as specified and as directed. |
| 24 | M&L for complete removal of existing treatment from old plastered surfaces of ceiling and applying two coat of oil bound distemper on ceiling over 2mm thick wall care putty and one coat of primer, complete all as specified and as directed. |
| 25 | M&L for applying Two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm on old painted surfaces including complete removal of existing treatment. |
| 26 | Dismaintling wall and ceiling boards (fibre, pulp, insulation, etc) or insulation boards / slabs / blankets, any thickness, including cover fillets all as specified and directed. |
| 27 | M&L Gl frame work for seamless ceiling comprising of Gl perimeter channnel 0.55 mm thick with two unequal flanges of 20 and 30 mm and web of 27 mm fixed to rounding wall using nylon sleeves and screws at 450 mm centre to centre/intermediate channel 0.9 mm thick having two equal flanges of 15 mm each and web of 45 mm suspended from soffit at approx 900 mm centre to centre with Gl cleat and steel expansion fasteners with and including ceiling section (not exc 1.2 m length) of 0.55mm thickness having kurled web of 50 mm and flange of 26 mm each with lips of 10.5 mm fixed to the intermediate channel with connecting clips across the intermediate channel at 457 mm centre to centre with level diffrence, complete all as specified and directed. |
| 28 | Note:- The frame will be fixed at two or more level (as per direction of Engr -In -Charge) for designer false ceiling. Rates for the same are included in above rates and nothing will be paid extra. |
| 29 | S&F 12mm thick Gypsum Board as in seamless ceiling fixed with screw as per manufacturers instructions including 3 mm thick cement base wall care putty in two layer including necessary taping etc and applying two coats of oil bound distemper on ceiling surfaces with level diffrence, complete all as specified and directed. Note:- The false ceiling will be fixed at two or more level (as per direction of Engr -In -Charge) for designer false ceiling. Rates for the same are included in above rates and nothing will be paid extra. |
| 30 | Taking down Chowkhats or frames with shutters (without taking off shutters from the frames) n exc 1.5 Sqm each complete all as specified and directed |
| 31 | Taking down chowkats or frames with Shutters (without taking off shutters from the frame 1.50 Sqm and n exc 4.00 Sqm each complete all as specified and directed |
| 32 | M&L for cement concrete 1:2:4 type B-1, using 20mm graded stone aggregate as in coping, bed blocks, filling of hold fast PCC or similar works including formwork complete all as specified and directed. |
| 33 | M&L Factory made single extruded WPC (Wood Polymer Composite) solid door/ window/ Ceosetory windows & other Frames/ Chowkhat of size 65 x100 mm single rebate comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/ cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2, modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire retardant and fixed in position with MS hold fast/ lugs/SS dash fasteners of required dia and length complete as per direction of Engineer-in-Charge. (M.S. hold fast/ lugs or SS dash fasteners shall be paid for separately). Note: For WPC solid door/window frames, minus 5mm tolerance in dimension i.e. depth and width of profile shall be acceptable. Variation in profile dimensions on plus side shall be acceptable but no extra payment on this account shall be made |
| 34 | S&F 28-30 mm thick moulded WPC factory made 100% solid door (conforming as per IS-4020) made from 100% lead free single extruded with 2, 4 or 6 raised panel design on the front side with 10 mm deep mould on single side with wood grain texture and back side palin with density not less than 600 Kg/cum. Manufactured by an ISO : 9001-2015 certified company. The door should be water proof, termite proof, fire retardant and having screw holding capacity complete all as specified |
| 35 | S&F 150 mm long Extruded stainless steel handles decorative designer type, polished complete all as specified and as directed. |
| 36 | S&F 125 mm long Butt hinges,Stainless steel, with mild steel hinge pin, bright polished and fixed, typeB-11 complete all as specified and as directed. |
| 37 | S&F 150mm size Stainless steel tower bolts, with cast or sheet barrel and rolled or cast bolts and fixed complete all as specified and as directed. |
| 38 | S&F factory made 100 % solid wood plastic composite (WPC) flush type shutter of 18mm thickness one side laminate consisting of panel of PVC profile of 18mm (+ 0.7mm) thick of denisity 600 kg per cum manufactured by ISO-9000 certified company using for shutter cillicia ply 18mm thick and fixed with frame. The thickness of shutter is edges painted by matching colour of PVC lining of plain/prelim coloured PVC sheet using etc complete as per manufacture specification. |
| 39 | S&F auto soft closing hinges 35 mm of 0 crank( KH-001) OR 8 crank (KH-002) openable at 110 degree for kitchen cabinet shutters Make :Hexa, Hettich, Hafele |
| 40 | S&F Ball bearing runners 450 mm Telescopic channel (KTS-20) full extension load capacity 50 kgs, Make :Hexa, Hettich, Hafele |
| 41 | S&F 125 mm long stainless steel handles decorative designer type, polished complete all as specified and as directed. |
| 42 | S&F Ball catches with 8mm dia steel ball, and brass body and striking plate including letting in and fixed |
| 43 | S&F in repair WPC (Wood Polymer Composite) indoor wall panel of size as per manufacturer instruction and thickness 15mm to 27mm designe fluted louvered combine wood fibres and polymers to create a durable, eco-friendly, and aesthetic interior cladding, including all necessary frame work fixed to wall complete and directed by Engr-In-Charge. |
| 44 | S&F in repair 25 mm dia stainless steel curtain rod with 1.25mm thick with funnels complete all as specified and directed by Engr-in-charge. |
| 45 | S&F SS heavy duty decorative brackets suitable for 25mm dia curtain rod (minimum projection from wall 75mm) fixed in wall including drilling, rawl plug, screws etc complete all as specified and directed. |
| 46 | S&F powder coated (minimum thickness of powder coating 50 micron) aluminium frame for doors, windows, ventilators and partition including fabrication of frame with one or more rebates including jointing clits for fixing etc complete all as specified by Engr-In- Charge. |
| 47 | S&F powder coated (minimum thickness of powder coating 50 micron) Aluminium door, window and ventilator shutters, side hung type without sash bars aluminium sections weighing 0,55kg/m including necessary cleats ,glazing clips,rubber packing ,anodised aluminium snap beading ,screws,anodised aluminium fittings such as peg stays150mmlong(01 Nos), hinges type B-21 100mm long (02 Nos), suitale handle (01 nos) complete all as specified. Note : (i) Glass panes/wire cloth will be measured & paid separately . Please Enable Macros to View BoQ information |
| 48 | S&F powder coated (minimum thickness of powder coating 50 micron) Aluminium door, window and ventilator shutters, side hung type without sash bars aluminium sections weighing 0,55kg/m including necessary cleats ,glazing clips,rubber packing ,anodised aluminium snap beading ,screws,anodised aluminium fittings such as peg stays150mmlong(01 Nos), hinges type B-21 100mm long (02 Nos), suitale handle (01 nos) complete all as specified. Note : (i) Glass panes/wire cloth will be measured & paid separately . Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Sep 25, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedOct 16, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 20 daysOct 21, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 25 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender