Tender For Rewiring Of Electrical Installation And Replacement Of Existing Light Fittings, Ceiling Fans And Defective Switchgear In Govt. Model High School Vikasnagar, Mauli Jagran, U.T., Chandigarh.
Tender Value
26.22 Lakhs
Estimated cost
Bid Submission
06 Oct 2026
6 days left
EMD
52450
Bank guarantee accepted
Document Fee
Ref. Documents
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Chandigarh → Chandigarh
EMD Exemption
Not Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for Rewiring Of Electrical Installation And Replacement Of Existing Light Fittings, Ceiling Fans And Defective Switchgear In Govt. Model High School Vikasnagar, Mauli Jagran, U.T., Chandigarh.
BOQ
| Sl. No. | Item Description |
| 1 | DSR item No.1.10 Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS/HFFR PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit, with modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm FRLS/HFFR PVC insulated copper conductor single core cable etc. as required. |
| 2 | Group-C |
| 3 | 1.15 Rewiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS/HFFR PVC insulated copper conductor single core cable and 1.5 sq.mm FRLS/HFFR PVC insulated copper conductor single core cable as earth wire in existing surface/ recessed steel/PVC conduit including dismantling as required. |
| 4 | Group-C |
| 5 | DSR item No. 1.17 Supplying and drawing following sizes of FRLS/HFFR PVC insulated copper conductor, single core cable in the existing surface/ recessed steel/ PVC conduit as required. |
| 6 | 3 x 1.5 sq. mm |
| 7 | 3 x 2.5 sq. mm |
| 8 | 3 x 4 sq. mm |
| 9 | 5 x 6sq. mm |
| 10 | DSR item No. 1.21 Supplying and fixing of following sizes of medium class PVC conduit along with accessories in surface/recess including cutting the wall and making good the same in case of recessed conduit as required. |
| 11 | 25 mm |
| 12 | 32 mm |
| 13 | DSR item No.1.24 Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required. |
| 14 | 5/6 A switch |
| 15 | 3 pin 5/6 A socket outlet |
| 16 | DSR 1.25 Supplying and fixing two module stepped type electronic fan regulator on the existing modular plate switch box including connections but excluding modular plate etc. as required. |
| 17 | DSR 1.26 Supplying and fixing modular blanking plate on the existing modular plate & switch box excluding modular plate as required. |
| 18 | DSR 1.27 Supplying and fixing following size/ modules, GI box alongwith modular base & cover plate for modular switches in recess etc. as required. |
| 19 | 1 or 2 Module (75 mm x75 mm) |
| 20 | 3 Module (100mmX75mm) |
| 21 | 4 Module (125 mm x 75 mm) |
| 22 | 6 Module (200 mm x 75 mm) |
| 23 | 12 Module (200 mm x 150 mm) |
| 24 | DSR 1.31 Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 3 pin 5/6 A modular socket outlet and 5/6 A modular switch, connections etc. as required. |
| 25 | DSR item No.1.32 Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 6 pin 5/6 A & 15/16 A modular socket outlet and 15/16 A modular switch, connections etc. as required. |
| 26 | DSR 1.33 Supplying and fixing 3 pin, 5 A ceiling rose on the existing junction box/ wooden block including connections etc. as required. |
| 27 | DSR 1.38 Supplying and fixing call bell/ buzzer suitable for single phase, 230 V, complete as required. |
| 28 | DSR item No.2.2 Providing and fixing following rating and breaking capacity and pole MCCB with thermomagnetic release and terminal spreaders in existing cubicle panel board including drilling holes in cubicle panel, making connections, Ics=100% Icu and Operational Voltage 690V etc. as required. |
| 29 | 100 A,30KA,FPMCCB |
| 30 | 250 A,36KA,FPMCCB |
| 31 | DSR Item No. 2.4 Supplying and fixing following way, horizontal type three pole and neutral, sheet steel, MCB distribution board, 415 V, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without (MCB/RCCB/Isolator) |
| 32 | 4 way (4 + 12), Double door |
| 33 | DSR Item No.2.5 Supplying and fixing of following ways surface/ recess mounting, vertical type, 415 V, TPN MCB distribution board of sheet steel, dust protected, duly powder painted, inclusive of 200 A tinned copper bus bar, common neutral link, earth bar, din bar for mounting MCBs (but without MCBs and incomer) as required (Note: Vertical type MCB TPDB is normally used where 3 phase outlets are required). |
| 34 | 8 way (4 + 24), Double door |
| 35 | DSR 2.10 Supplying and fixing 5 A to 32 A rating, 240/415 V, 10 kA, \\"C\\" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required. |
| 36 | Single Pole |
| 37 | Triple Pole |
| 38 | Triple Pole & Neutral |
| 39 | DSR item No.2.14 Supplying and fixing following rating, double pole, (single phase and neutral), 240 V, residual current circuit breaker (RCCB), having a sensitivity current 30 mA in the existing MCB DB complete with connections, testing and commissioning etc. as required. |
| 40 | DSR item No.1.57 Supplying & fixing suitable size GI box wih modular plate and cover in front on surface or in recess including providing and fixing 25 A modular socket outlet and 25 A modular SP MCB, \\"C\\" curve including connections, painting etc. as required. |
| 41 | DSR 5.2 Earthing with G.I. earth pipe 4.5 metre long, 40 mm dia including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe etc. with charcoal/ coke and salt as required. |
| 42 | DSR item No.5.12 Providing and laying earth connection from earth electrode with 6 SWG dia G.I. Wire in 15 mm dia G.I. pipe from earth electrode including connection with G.I. thimble excavation and re-filling as required. |
| 43 | DSR item No.5.16 Providing and fixing 6 SWG dia G.I. wire on surface or in recess for loop earthing as required. |
| 44 | DSR item No.8.1 LED Down lighter (SMD Type) (System lumen efficacy ≥ 105 < 120 lm/Watt )(Please refer DNIT for complete specification of item no.22) |
| 45 | 18 watt |
| 46 | DSR item No.8.9 LED Batten light (System lumen efficacy ≥105 <120 lm/Watt).(Please refer DNIT for complete specification of item no.23) |
| 47 | 24 -26watt |
| 48 | DSR item No.8.16 LED Flood Light, powder coated pressure die cast aluminium (System lumen efficacy ≥120 and <135 lm/Watt).(Please refer DNIT for complete specification of item no.24) |
| 49 | 150 Watt. |
| 50 | DSR item No.9.2 Brush Less Direct Current (BLDC) Fan without Remote(Please refer DNIT for complete specification of item no.25) |
| 51 | 1400mm, service value ≥ 6.0 CM/Min/Watt, air delivery 245 CM/Min (Minimum) |
| 52 | DSR 11.1 Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required. |
| 53 | 4 X 10 Sq mm (25 mm) |
| 54 | 3½ X 35 sq. mm (32mm) |
| 55 | 3½ X 50 sq. mm (35mm) |
| 56 | 3½ X 120 sq. mm (45mm) |
| 57 | S/E of on load change over switch of 250 Amp. 4 pole 415 Volt with enclosure. The changeover switch should be of Havells/ Lauritz Knudsen/ Siemens/ Schneider/ABB/ Hager make only. The Changeover switch should be installed in existing cubicle panel / angle iron board/ including drilling holes in cubicle panel / angle iron board, making connections with suitable rating of copper wire / copper strip etc. as required. The job includes the cost of all petty material and labour charge etc as required to complete the job to the entire satisfaction of Engineer-in-charge. |
| 58 | Supply fabrication & erection of M.S. angle iron board covered with 14 GMS sheet fixed in to the nitch for mounting switchgear. The board shall be fabricated out of 40mm x 40mm x 5mm angle iron frame and shall be covered with a 14 GMS sheet duly welded for erection of switchgear on it. The switches /BDB’s / ELCB shall be provided with required no. of supporting member of M.S. flat 25mm x 5mm to bring all the switchgear in one level including bonding the board switchgear etc. to the existing earth. The board shall be painted with two coat of approved shade of superior quality paint after one coat of primer. The rate includes carriage from factory to site, erection charges in the niche and other petty material required at site of work. |
| 59 | Supply & erection of Adopter box of suitable size required made out of 16GMS sheet The box to be provided with front detachable cover and having holes of out going/ incoming pipe/ cable/ wire/ pipe. The boxes shall be painted with 2 coats of approval paint after applying one coat of primer. The size and design of the boxes shall be as per actual requirement at site. The box is fixed on existing surface by rawl plugs/ screws etc. suitable |
| 60 | Supply & erection of fan hook for erection of ceiling fan. The hook shall be made out ½” dia MS bar in U shape formation. It shall be fixed after chasing the RCC slab and making necessary repair, plaster and making its original position. |
| 61 | Supply and erection of sheet metal bus-bar chamber on existing surface with required No. of bus-bar strips of suitable length and cross-sectional area, made of copper strips of suitable length and cross-sectional area enclosure made of M.S. sheet 1.6mm thick with detachable cover fitted with dust excluding gasket and secured with sufficient No. of cadmium plated iron screws and of given overall dimensions and to be fixed with G.I. bolts and nuts/Rag bolts and nuts etc., complete with all accessories including connections with suitable size tin coated copper thimbles, bonding to the existing earth and painting etc. as desired by the Engineer-in-charge. |
| 62 | Sheet metal bus-bar chamber suitable for 300 Amp. 4’ long 415 Volts capacity with 4 copper strip Bus-bars each of length 1200 mm & cross-sectional area (31.75mm x 6.35mm) enclosure having overall dimensions (1280mm x 500mm x 200mm) nominal. |
| 63 | S/E of 3mm thick white glazed Bakelite sheet on the existing M.S box. The job includes the cost of sheets and making holes and cutting charges of switches & sockets. The job includes the cost of all labour & petty material required to complete the job. The Bakelite sheet should be of Superhylam/ Greenlam/ Formica make only. |
| 64 | Supply and fixing of 12 modules (200 mm x 150 mm) G.I box suitable for accommodate the following accessories along with modular base and cover plate for modular switches in recess/ surface etc as required for Computer Point with 4 Nos. 5/6 Amp. modular switch and 4 Nos. 3 pin 5/6 Amp. modular socket outlet. The job includes the cost of making interconnections with suitable copper wire, painting of box with approved paint and other petty material required to complete the job to the entire satisfaction of Engineer-in-Charge at site. The Modular accessories should be of Lauritz Knudsen (Entice) / ABB (Ivie) / Legrand (Myrius) / Crabtree (Athena)/ Norisys (Square series) make only. |
| 65 | Supply & fixing of OEM made Junction box IP-66/67 made out of Polycarbonate with Glass fiber reinforced of size 210x155x90 (minimum) with 5 nos. OEM made connectors/ terminal blocks. The Jn. Box and connectors/ terminal blocks should be supplied by OEM. The terminal blocks/ connectors should be of Hensel/ Wago/ Elmax/ Siemens make only and junction box shall be of Hensel make KF-1616 G or its equivalent Clipsal/ Legrand/ Rittal/ Schneider/ ABB make only. The Junction box shall be fire retardant and self-extinguishing. The gasket material shall be polyurethane and the gasket shall be internally embedded. The job includes the cost of cable glands for cable entry, mounting kit for pipe and post installation, fixing screw, all labour and petty material required to complete the job to the entire satisfaction of the Engineer in Charge of work. |
| 66 | Supply and erection of MS bracket F type suitable size and suitable shape made form 40mm x 40mm x 5mm thick angle iron to be installed on exiting parapet/ wall with help of suitable size of nuts and bolts etc. for erection of existing LED flood light fittings. The job also includes the cost of painting of box with superior quality of paint and other petty material etc as per required to complete the job. |
| 67 | Supply and laying of XLPE insulated PVC sheathed Aluminum conductor armoured cable of 1.1 KV grade as per IS 7098 (Part-I) 1988 (amended up to date) of the following sizes to be laid in existing Trench/Ducts/Cable Tray/ RCC/ HUME/ METAL/ DWC pipe / on surface with the help of MS clamps of suitable size/ as required at site to the entire satisfaction of Engineer-in-Charge. The job includes labour charges of laying the cable and making connections with suitable size aluminum lugs/thimbles etc. The cable shall be of Polycab / Havells / R.R. Kabel/ KEI/ Finolex make only. |
| 68 | 50 sq.mm 3.5 core (On surface) |
| 69 | 10 sq.mm 4 core (On surface) |
| 70 | LED Panel light 1x4 ft. (System lumen efficacy ≥120 <135 lm/Watt) (Recessed/ Surface type)(Please refer DNIT for complete specification of item no.37) |
| 71 | 33 Watt./ 36 Watt. Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Sep 25, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedOct 06, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 6 daysOct 06, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 6 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender