Tender For Special Repair To Building No Et 205 And Provn Of Automatic Organic Waste Converter Composit Machine 100 Kg Alongwith A Shed At Changsari Under Ge Rangia
Tender Value
30 Lakhs
Estimated cost
Bid Submission
16 Oct 2026
12 days left
EMD
60000
Bank guarantee accepted
Document Fee
500
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Baksa → Assam
EMD Exemption
Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for Special Repair To Building No Et 205 And Provn Of Automatic Organic Waste Converter Composit Machine 100 Kg Alongwith A Shed At Changsari Under Ge Rangia
BOQ
| Sl. No. | Item Description |
| 1 | Dismantling unframed timber scantlings 40 Sq cm and over in section and in any position complete all as specified and as directed. |
| 2 | Taking down chowkat or frame with shutter not exceeding 1.5 Sqm (without taking off shutter from the frame), complete all as specified and as directed. |
| 3 | Dismantling of unframed fillets, rails, posts, rafters, purlins etc., under 40 Sq. Cm in section complete all as specified and as directed. |
| 4 | Taking down chowkat or frame with shutter exceeding 1.5 Sqm but not exceeding 4 Sqm each (without taking off shutter from the frame), complete all as specified and as directed. |
| 5 | Dismantling Asbestos cement (corrugated, semi-corrugated, etc.) sheets in roof coverings, complete all as specified and as directed. |
| 6 | Demolition of reed, lathing, single or double, including battens and plaster or chicken wire lathing, complete all as specified and as directed. |
| 7 | Demolition of brick work or stone/boulder masonry, built in cement mortar including all quoins, arches, pillars, etc., complete all as specified and as directed. |
| 8 | Dismantling wall and ceiling boards (fibre, pulp, insulation etc.) any thickness, including cover fillets complete all as specified and as directed. |
| 9 | M&L for Brickwork with subclass ‘B’ bricks, straight or curved on plan to any radius in half brick thick walls built and set in cement mortar 1:4, complete all as per specified and as directed. |
| 10 | S&F of Stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples, complete all as specified and as directed. |
| 11 | M&L, 10 mm thick rendering in CM 1:6 on other than fair faces of brick work or concrete block surfaces finished fair and even without using extra cement complete all as specified and as directed. |
| 12 | M&L for Rendering (Externally) 15mm thick in Cement Mortar 1:4 in two layers on other than fair faces Brick Walls/Concrete Surfaces/ other side of lathing, 5mm thick top layer mixed with WPC as per Manufactures instruction, plastered surfaces finished Even and Smooth without using Extra Cement, complete all as specified and as directed. NOTE: WPC shall be Measured and Paid as ‘Supply only’ under relevant Item. |
| 13 | Supply only liquid water proofing compound conforming to relevant IS complete all as specified and as directed. |
| 14 | M&L for preparing new plastered surfaces and applying two coats of acrylic based distemper on wall surfaces including chalk whitening preparatory to distempering complete all as specified and as directed. |
| 15 | M&L for preparing newly plastered surfaces of walls and applying two coats of cement base paint over one coat of primer, complete all as per specified and as directed. |
| 16 | S&F of TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips, complete all as specified and as directed. |
| 17 | S&F of TMT bars 6-8mm dia, cut to length, bent to shape required, in stirrups, spacers and binders and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips, complete all as specified and as directed. |
| 18 | S&F of Steel work in tubular trusses including special shaped washer etc. complete using ERW or induction butt welded tubes conforming to I. S.1161- 1979 grade St.-240, complete all as specified and as directed. |
| 19 | M&L for Preparation of new or previously untreated steel surfaces of any description, over 10 cm width or girth, not otherwise described and applying two coats of black japan paint over a coat of red oxide zinc chrome primer complete all as specified and as directed. |
| 20 | Use and Waste for formwork to sides of pillars, posts, struts, piers, columns and stanchions, rough finished flat surfaces of concrete, complete all as specified and as directed. |
| 21 | Use and waste for Formwork to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelves including supports, overhangs, etc. also splays between floors and beams, etc., rough finished flat surfaces of concrete, complete all as specified and as directed. |
| 22 | M&L for providing 75 mm thick Cement concrete type C-2, 1:3:6 (40mm graded stone aggregate) as in floor/ path/ hardstanding/plinth protection, etc. or similar works, laid in altenate bays including use and waste of form work and finishing concrete surfaces even and fair, complete all as per specified and as directed. |
| 23 | M&L for Reinforced Cement Concrete (Nominal Mix) type B1, 1:2:4 (20mm graded stone aggregate) in Columns, pillars, piers, posts and struts, complete all as specified and as directed.NOTE : Reinforcement & Formwork will be measured and paid separately under relevant Item. |
| 24 | M&L for Reinforced Cement Concrete (Nominal Mix) type B1, 1:2:4 (20mm graded stone aggregate) in Beams, cantilevers, bressummers, lintels over 1.5m span, complete all as specified and as directed.NOTE : Reinforcement & Formwork will be measured and paid separately under relevant Item. |
| 25 | S&F of 0.50mm thick Pre-painted galvalume aluminum zinc coating GI based corrugated steel sheet of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws, complete all as specified and as directed. |
| 26 | S&F of 0.50mm thick Pre-painted galvalume aluminum zinc coating GI based plain steel sheet of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws, complete all as specified and as directed. |
| 27 | S&F of Factory Made Solid PVC Moulded Door Shutter With wood free EPS, 28 to 30mm thick (stiles), with 2, 4, or 6 raised panel design with 2mm thick Moulded Prelam PVC Sheet on the front face & 2mm prelam PVC Sheet on back face; complete all as specified and as directed. |
| 28 | S&F of Factory made solid panel one side prelam PVC door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement; complete all as specified and as directed by Engineer-in-charge. |
| 29 | S&F of Solid PVC Door Frame of size 50mm x 47mm made out of 5mm single side prelam PVC sheet reinforced with M.S. Square tube; complete all as specified and as directed by Engineer-in-charge. |
| 30 | M&L for Aluminium framed windows, anyb pattern, fixed/side hung/sliding (two or three track) using Aluminium section of approved make with or without sash bars suitable for 4mm thick glazing including necessary joining cleats, glazing clips, aluminium snap beading, handle, locking arrangement etc complete all as specified and as directed. Note : Glazing shall be measured and paid seperately. |
| 31 | S&F of 4.8 mm thick Sheet glass, ordinary quality in square exc 0.5 sq. m in each pane fixed with cut and mitred beads extra over sheet glass, ordinary quality, if sheet glass is ground or obscured or frosted on one side complete all as specified and as directed by Engineer-in-charge. |
| 32 | S&F of 200 mm long Aluminium anodised, barrel tower bolts of extruded section, complete all as specified and as directed by Engineer-in-charge. |
| 33 | S&F 100mm long medium weight cold rolled mild steel butt hinges with galvanised mild steel hinge pin type C-21 complete all as specified and as directed. |
| 34 | S&F Mild steel 300mm, ordinary rat tail rod pattern springs including roller and roller plate complete all as specified and as directed. |
| 35 | S&F of 100 mm long Aluminium anodised, barrel tower bolts of extruded section, complete all as specified and as directed by Engineer-in-charge. |
| 36 | S&F of 100 mm long Extruded aluminium alloy handles, fabricated type, anodised, complete all as specified and as directed by Engineer-in-charge. |
| 37 | S&F 75mm long medium weight cold rolled mild steel butt hinges with galvanised mild steel hinge pin type C-21 complete all as specified and as directed. |
| 38 | S&F in-repair of 20 mm dia mild steel, chromium plated curtain rail with fixing brackets, stops, rollers etc., complete all as specified and as directed by Engineer-in-charge. |
| 39 | M&L for providing Non-skid Ceramic coloured tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.18 sqm but not exceeding 0.36 sqm, in floors etc., laid over 15mm thick cement screed 1:6 set and jointed in neat cement slurry and pointed in white or coloured cement to match, complete all as per specified and as directed by Engineer-in-charge. |
| 40 | M&L for providing Glazed ceramic coloured tiles in vertical surface (like skirting, dado, etc.) 300x 450x 7 mm thick, over 10mm thick cement screed 1:4 set and jointed in neat cement slurry and pointed in white or colour cement to match, complete all as per specified and as directed by Engineer-in-charge. |
| 41 | S&F in-repair of powder coated Gl frame work for seamless ceiling comprising of Gl perimeter channnel 0.55 mm thick with two unequal flanges of 20 and 30 mm and web of 27mm fixed to surrounding wall using nylon sleeves and screws at 450 mm centre to centre/intermediate channel 0.9 mm thick having two equal flanges of 15 mm each and web of 45 mm suspended from soffit at approx 900 mm centre to centre with Gl cleat and steel expansion fasteners with and including ceiling section (not exc 1.2 m length) of 0.55 mm thickness having kurled web of 50 mm and flange of 26 mm each with lips of 10.5 mm fixed to the intermediate channel with connecting clips across the intermediate channel suspended from ceiling by means of 3mm dia GI hanger with and including supplying & fixing/ laying/ inserting of pre-painted (white) 4mm thick designer classic E-boards (595x595 mm) to GI frame work, complete all as specified and as directed by Engineer-in-charge., complete all as per specified and as directed. |
| 42 | M&L for Surface excavation n.exc 30cm deep and averaging 15cm deep and getting out in soft/loose soil, complete all as per specified and as directed. |
| 43 | Excavation in post holes (or similar holes) each n.exc 0.5cum in soft/loose soil and getting out, returning filling in and ramming earth or broken rubble mixed with earth around in layers not exceeding 25cm, watering and removing of surplus soil to a distance n.exc 50 meters and making good surface, complete all as per specified and as directed. |
| 44 | Removing excavated material not exc. 50 m & depositing where directed at a level not exc. 1.5 m above starting point complete all as per specified and as directed. |
| 45 | M&L for PCC 1:4:8 type D-2 (40mm graded stone aggregate) as in foundations, fillings and mass concrete complete all as per specified and as directed. |
| 46 | S&F of mild steel Plates (plain or chequered) channels, square cut or notched (ordinary and counter sunk) forming holes, without any attachment, confirming to Fe 410-W (Gde- E- 250) quality-A, complete all as specified and as directed. Please Enable Macros to View BoQ information |
| 47 | S&F of mild steel Plates (plain or chequered) channels, square cut or notched (ordinary and counter sunk) forming holes, without any attachment, confirming to Fe 410-W (Gde- E- 250) quality-A, complete all as specified and as directed. Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Sep 25, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedOct 16, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 12 daysOct 22, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 18 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender