Tender For special Repairs/Replacement Of Lt Network In Dsc Otm Bldg, Dsc Md Accn, Nc(E) And 84 Md Accn Area In Domestic Area Of Afs Yelahanka.
Tender Value
68.51 Lakhs
Estimated cost
Bid Submission
22 Oct 2026
4 days left
EMD
1.27 Lakhs
Bank guarantee accepted
Document Fee
1000
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Bengaluru Urban → Karnataka
EMD Exemption
Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for special Repairs/Replacement Of Lt Network In Dsc Otm Bldg, Dsc Md Accn, Nc(E) And 84 Md Accn Area In Domestic Area Of Afs Yelahanka.
BOQ
| Sl. No. | Item Description |
| 1 | Fabricate, supply ,install testing and commissioning of LT panel Outdoor type in replacement 415 Volts, 50 Hz, 3 phase, 4 wire for accomodating the following accessories totaly enlosed self supporting structure fully compartmentalized suitable for outdoor use with bottom cable entry with suitable cable glands made out of CRCA sheet 3.15mm thick with angle iron frame works with suitable legs of ISA 50x50x5mm with four legs grouted PCC (1:2:4) type B1, foundation block with suitable monting arrangement for aluminium bus bars 300 Amps capacity, hindged door at front with suitable locking arrangement, provision of louvers at sides, CPRI approved, dust and vermin proof, powder coated and with following asseccories suitable for incoming/outgoing arrangements complete all as specifed and directed:- INCOMER :-(a) 4 Pole MCCB 200 Amp, (with thermal magnetic release) 50 Hz, 415 V with rupturing capacity 25 KA, -1 NoOUTGOING(b) 4 Pole MCCB 125 Amp, (with thermal magnetic release),50 Hz, 415 V with rupturing capacity 25 KA, -01 No(d) 4 Pole MCCB 63 Amp, (with thermal magnetic release), 50 Hz, 415 V with rupturing capacity 16 KA, -02 No(e) 4 Pole MCCB 40 AMps , (with thermal magnetic release), 50 Hz , 415V with rupturing capacity 16 KA -02 Nos (e) Multifunctional VAF Meter -01 No(f) Digital Ammeter-01 N(g) CT's 200/5- set of 3 No(h) LED type Indication lamps (RYB)-one set(For each incoming and outgoing) Note : (i) Contractor has to get the approval of drawings of LT panel from the Engr In Charge /GE before commencement of work. (ii) Switich gear and connected items should be of approved make. (iii) Bottom portion of panel should be 45 CM above from the ground level. |
| 2 | Fabricate, supply ,install testing and commissioning of LT panel outdoor type in replacement 415 Volts, 50 Hz, 3 phase, 4 wire for accomodating the following accessories totaly enlosed self supporting structure fully compartmentalized suitable for indoor use with bottom cable entry with suitable cable glands made out of CRCA sheet 3.15mm thick with angle iron frame works with suitable legs of ISA 50x50x5mm with four legs grouted PCC (1:2:4) type B1, foundation block with suitable monting arrangement for aluminium bus bars 300 Amps capacity, hindged door at front with suitable locking arrangement, provision of louvers at sides, CPRI approved, dust and vermin proof, powder coated and with following asseccories suitable for incoming/outgoing arrangements complete all as specifed and directed:- INCOMER (a) Onload change over switch 4 Pole 200 Amps (Incomer )-01 nosOUTGOING ( b) 4 Pole MCCB 125 Amp (With thermal and magnetic settings) , 50 Hz, 415 V with rupturing capacity 25 KA,-01 No(c) 4 Pole MCCB 63 Amp,(With thermal and magnetic settings) 50 Hz, 415 V with rupturing capacity 25 KA, -04 No(d) Digital Multifunctional VAF Meter -01Nos (e) CT's 200/5- set of 3 (g) LED type Indication lamps (RYB)-one set of 03 (for each incoming and outgoing)Note : (i) Contractor has to get the approval of drawings of LT panel from the Engr In Charge /GE before commencement of work. (ii) Switich gear and connected items should be of approved make. (iiI) Bottom portion of panel should be 45 CM above from the ground level. |
| 3 | Fabricate, supply ,install testing and commissioning of LT panel outdoor type inreplacement, 415 Volts, 50 Hz, 3 phase, 4 wire Suitable for accomodating the following accessories totaly enlosed self supporting structure fully compartmentalized suitable for outdoor use with bottom cable entry with suitable cable glands made out of CRCA sheet 3.15mm thick with angle iron frame works with suitable legs of ISA 50x50x5mm with four legs grouted PCC (1:2:4) type B1, foundation block with suitable monting arrangement for aluminium bus bars 300 Amps capacity, hindged door at front with suitable locking arrangement, provision of louvers at sides, CPRI approved, dust and vermin proof, powder coated and with following asseccories suitable for incoming/outgoing arrangements complete all as specifed and directed:-INCOMER (a) On load changeover switch 200 Amps , Incomer -1 NoOUTGOING (b) 4 Pole MCCB 160 Amp, with thermal and magnetic release, 50 Hz, 415 V with rupturing capacity 25 KA,-01 No(c) 4 Pole MCCB 63Amp, with thermal and magnetic release ,50 Hz, 415V with rupturing capacity 25 KA- 41 No(d) TPN MCB 32 Amp,50 Hz, 415V with rupturing capacity 10 KA- 01 No(d) Multifunctional VAF meter -01 Nos (f) CT's 200/5- set of 3 No(g) LED type Indication lamps (RYB)-one set(for each incoming and outgoing) Note : (i) Contractor has to get the approval of drawings of LT panel from the Engr In Charge /GE before commencement of work. (ii) Switich gear and connected items should be of approved make. (iiI) Bottom portion of panel should be 45 CM above from the ground level. |
| 4 | Fabricate, supply ,install testing and commissioning of LT panel Outdoor type in replacement 415 Volts, 50 Hz, 3 phase, 4 wire for accomodating the following accessories totaly enlosed self supporting structure fully compartmentalized suitable for outdoor use with bottom cable entry with suitable cable glands made out of CRCA sheet 3.15mm thick with angle iron frame works with suitable legs of ISA 50x50x5mm with four legs grouted PCC (1:2:4) type B1, foundation block with suitable monting arrangement for aluminium bus bars 300 Amps capacity, hindged door at front with suitable locking arrangement, provision of louvers at sides, CPRI approved, dust and vermin proof, powder coated and with following asseccories suitable for incoming/outgoing arrangements complete all as specifed and directed:- INCOMER :-(a) 4 Pole MCCB 200 Amp, (with thermal magnetic release) 50 Hz, 415 V with rupturing capacity 25 KA, -1 NoOUTGOING(b) 4 Pole MCCB 125 Amp, (with thermal magnetic release),50 Hz, 415 V with rupturing capacity 25 KA, -01 No(d) 4 Pole MCCB 63 Amp, (with thermal magnetic release), 50 Hz, 415 V with rupturing capacity 16 KA, -02 No(e) 4 Pole MCCB 40 AMps , (with thermal magnetic release), 50 Hz , 415V with rupturing capacity 16 KA -02 Nos (e) Multifunctional VAF Meter -01 No(f) Digital Ammeter-01 No(g) CT's 200/5- set of 3 No(h) LED type Indication lamps (RYB)-one set (For each incoming and outgoing ) Note : (i) Contractor has to get the approval of drawings of LT panel from the Engr In Charge /GE before commencement of work. (ii) Switich gear and connected items should be of approved make. (iiI) Bottom portion of panel should be 45 CM above from the ground level. |
| 5 | Fabricate, supply ,install testing and commissioning of LT panel outdoor type in replacement 415 Volts, 50 Hz, 3 phase, 4 wire for accomodating the following accessories totaly enlosed self supporting structure fully compartmentalized suitable for indoor use with bottom cable entry with suitable cable glands made out of CRCA sheet 3.15mm thick with angle iron frame works with suitable legs of ISA 50x50x5mm with four legs grouted PCC (1:2:4) type B1, foundation block with suitable monting arrangement for aluminium bus bars 300 Amps capacity, hindged door at front with suitable locking arrangement, provision of louvers at sides, CPRI approved, dust and vermin proof, powder coated and with following asseccories suitable for incoming/outgoing arrangements complete all as specifed and directed:- INCOMER (a) Onload change over switch 4 Pole 200 Amps (Incomer )-01 nosOUTGOING ( b) 4 Pole MCCB 125 Amp (With thermal and magnetic settings) , 50 Hz, 415 V with rupturing capacity 25 KA,-01 No(c) 4 Pole MCCB 63 Amp,(With thermal and magnetic settings) 50 Hz, 415 V with rupturing capacity 25 KA, -04 No(d) Digital Multifunctional VAF Meter -01Nos (e) CT's 200/5- set of 3 (g) LED type Indication lamps (RYB)-one set of 03 (for each incoming and outgoing)Note : (i) Contractor has to get the approval of drawings of LT panel from the Engr In Charge /GE before commencement of work. (ii) Switich gear and connected items should be of approved make. (iiI) Bottom portion of panel should be 45 CM above from the ground level. |
| 6 | Fabricate, supply ,install testing and commissioning of LT panel outdoor type in replacement 415 Volts, 50 Hz, 3 phase, 4 wire for accomodating the following accessories totaly enlosed self supporting structure fully compartmentalized suitable for outdoor use with bottom cable entry with suitable cable glands made out of CRCA sheet 3.15mm thick with angle iron frame works with suitable legs of ISA 50x50x5mm with four legs grouted PCC (1:2:4) type B1, foundation block with suitable monting arrangement for aluminium bus bars 200 Amps capacity, hindged door at front with suitable locking arrangement, provision of louvers at sides, CPRI approved, dust and vermin proof, powder coated and with following asseccories suitable for incoming/outgoing arrangements complete all as specifed and directed:- INCOMER (a) 4 Pole MCCB 125 Amp,(With thermal and magnetic settings) 50 Hz, 415 V with rupturing capacity 25 KA, Incomer -1 NoOUTGOING (b) 4 Pole MCCB 40 Amp,(With thermal and magnetic settings) 50 Hz, 415 V with rupturing capacity 16 KA-06 Nos(c) Digital Multifunctional VAF Meter -01 nos(d) CT's 200/5- set of 3 No(e) LED type Indication lamps (RYB)-one set (for each incoming and outgoing)Note : (i) Contractor has to get the approval of drawings of LT panel from the Engr In Charge /GE before commencement of work. (ii) Switich gear and connected items should be of approved make. (iiI) Bottom portion of panel should be 45 CM above from the ground level. |
| 7 | Fabricate, supply ,install testing and commissioning of LT panel Outdoor type in replacement ,415 Volts, 50 Hz, 3 phase, 4 wire suitable for accomodating the following accessories totaly enlosed self supporting structure fully compartmentalized suitable for outdoor door use with bottom cable entry with suitable cable glands made out of CRCA sheet 3.15mm thick with angle iron frame works with suitable legs of ISA 50x50x5mm with four legs grouted PCC (1:2:4) type B1, foundation block with suitable monting arrangement for aluminium bus bars 400 Amps capacity, hindged door at front with suitable locking arrangement, provision of louvers at sides, CPRI approved, dust and vermin proof, powder coated and with following asseccories suitable for incoming/outgoing arrangements complete all as specifed and directed:- INCOMER (a) Onlaod changeover switch 315 Amps 4 Pole -1 NoOUTGOING (b) 4 Pole MCCB 200 Amp (With thermal and magnetic settings), 50 Hz, 415 V with rupturing capacity 25 KA-01Nos (c) 4 Pole MCCB 125 Amp(With thermal and magnetic settings), 50 Hz, 415 V with rupturing capacity 25 KA-01 Nos (d) MCCB 4 Pole 63 Amps(With thermal and magnetic settings), 50 Hz 415V with rupturing capacity 16 KA -01 Nos (d) Digita VAF Ammeter-01 No(f) CT's 315/5- set of 3 No(e) LED type Indication lamps (RYB)-one setNote : (i) Contractor has to get the approval of drawings of LT panel from the Engr In Charge /GE before commencement of work. (ii) Switich gear and connected items should be of approved make. (iiI) Bottom portion of panel should be 45 CM above from the ground level. |
| 8 | Fabricate, supply ,install testing and commissioning of LT panel Outdoor type in replacement, 415 Volts, 50 Hz, 3 phase, 4 wire suitable for accomodating the following accessories totaly enlosed self supporting structure fully compartmentalized suitable for outdoor door use with bottom cable entry with suitable cable glands made out of CRCA sheet 3.15mm thick with angle iron frame works with suitable legs of ISA 50x50x5mm with four legs grouted PCC (1:2:4) type B1, foundation block with suitable monting arrangement for aluminium bus bars 400 Amps capacity, hindged door at front with suitable locking arrangement, provision of louvers at sides, CPRI approved, dust and vermin proof, powder coated and with following asseccories suitable for incoming/outgoing arrangements complete all as specifed and directed:-INCOMER (a) 4 Pole MCCB 320 Amp,(With thermal and magnetic settings) 50 Hz, 415 V with rupturing capacity 36 KA, Incomer -1 NoOUTGOING (b) 4 Pole MCCB 200 Amp,(With thermal and magnetic settings) 50 Hz, 415 V with rupturing capacity 25 KA-01Nos (c) 4 Pole MCCB 125 Amp,(With thermal and magnetic settings) 50 Hz, 415 V with rupturing capacity 25 KA-01 Nos (d) 4 Pole MCCB 63 AMps(With thermal and magnetic settings) MCCB 25 KA -01 Nos (e) MCB SPN 40 Amps 10 KA -01 Nos (f) Digital VAF Meter -01 nos (g) CT's 400/5- set of 3 No(h) LED type Indication lamps (RYB)-one setNote : (i) Contractor has to get the approval of drawings of LT panel from the Engr In Charge /GE before commencement of work. (ii) Switich gear and connected items should be of approved make. (iiI) Bottom portion of panel should be 45 CM above from the ground level. |
| 9 | Fabricate, supply ,install testing and commissioning of LT panel Outdoor type in replacement 415 Volts, 50 Hz, 3 phase, 4 wire suitable for accomodating the following accessories totaly enlosed self supporting structure fully compartmentalized suitable for outdoor door use with bottom cable entry with suitable cable glands made out of CRCA sheet 3.15mm thick with angle iron frame works with suitable legs of ISA 50x50x5mm with four legs grouted PCC (1:2:4) type B1, foundation block with suitable monting arrangement for aluminium bus bars 300 Amps capacity, hindged door at front with suitable locking arrangement, provision of louvers at sides, CPRI approved, dust and vermin proof, powder coated and with following asseccories suitable for incoming/outgoing arrangements complete all as specifed and directed:- INCOMER (a) 4 Pole MCCB 200 Amp,(With thermal and magnetic settings) 50 Hz, 415 V with rupturing capacity 25 KA, Incomer -1 NoOUTGOING (b) 4 Pole MCCB 125 Amp,(With thermal and magnetic settings) 50 Hz, 415 V with rupturing capacity 25 KA-02Nos (c) 4 Pole MCCB 100 Amp,(With thermal and magnetic settings) 50 Hz, 415 V with rupturing capacity 25 KA-01 Nos (d) MCCB 4P 63 Amps (With thermal and magnetic settings) 25 KA -01 Nos (e) MCB SPN 40 AMps -02 Nos (f) Digital VAF Meter -01 Nogf) CT's 300/5- set of 3 No(h) LED type Indication lamps (RYB)-one setNote : (i) Contractor has to get the approval of drawings of LT panel from the Engr In Charge /GE before commencement of work. (ii) Switich gear and connected items should be of approved make. (iiI) Bottom portion of panel should be 45 CM above from the ground level. |
| 10 | Fabricate, supply ,install testing and commissioning of LT panel Outdoor type in replacement 415 Volts, 50 Hz, 3 phase, 4 wire suitable for accomodating the following accessories totaly enlosed self supporting structure fully compartmentalized suitable for outdoor door use with bottom cable entry with suitable cable glands made out of CRCA sheet 3.15mm thick with angle iron frame works with suitable legs of ISA 50x50x5mm with four legs grouted PCC (1:2:4) type B1, foundation block with suitable monting arrangement for aluminium bus bars 400 Amps capacity, hindged door at front with suitable locking arrangement, provision of louvers at sides, CPRI approved, dust and vermin proof, powder coated and with following asseccories suitable for incoming/outgoing arrangements complete all as specifed and directed:- INCOMER (a) Onload changeover switch 4 Pole 200 Amps -01 NosOUTGOING (b) 4 Pole MCCB 160 Amp,(With thermal and magnetic settings) 50 Hz, 415 V with rupturing capacity 25 KA-01Nos (c) 4 Pole MCCB 125 Amp,(With thermal and magnetic settings) 50 Hz, 415 V with rupturing capacity 25 KA-01 Nos (d) 4 Pole MCCB 63 Amps (With thermal and magnetic settings) 4 Pole 16KA -03 Nos (e) Digital VAF Meter -01 No(f) CT's 300/5- set of 3 No(e) LED type Indication lamps (RYB)-one setNote : (i) Contractor has to get the approval of drawings of LT panel from the Engr In Charge /GE before commencement of work. (ii) Switich gear and connected items should be of approved make. (iiI) Bottom portion of panel should be 45 CM above from the ground level. |
| 11 | M & L for Earthing complete with galvanised earth plate electrode of size 600x600x6 mm thick burried directly in ground earth pit not less than 2.25 m below ground level with top edge of earth plate not less than 1.5 mtrs below ground level connected to 25X4 mm galvanised iron strip as earth lead upto a length of 7.5 metre long by means of bolts,nuts, washers etc. and protected by GI pipe light grade 15mm dia and 20mm dia GI tubing light grade with funnel for watering, all as shown in electrical plate No 3 of SSR Part-I, back-fill with salt and charcoal, provision of test point including connected to earth test point and necessary earth work excavation in any type of soil PCC (1:3:6) type C1 bed and chamber RCC (1:2:4) type B1, iron grill including GI cover with hinge and funnel watering pipe etc all as specified and directed (Note : 1. If the desired earth resistance is not found earthing shall be re-done by the Contractor at no extra cost .) |
| 12 | Supply and laying in trenches, LT underground cable of size 10 Sqmm 4 core XLPE insulated armoured and PVC sheathed 1100 Volts grade with aluminium conductor multistranded including cable connecting lugs, glands,jointing materials etc., laid in trenches, floors, roof, ducts and fixing using clamps, saddle for pole, wall including taking down complete all as directed . |
| 13 | Supply and laying in trenches, LT underground cable of size 16 Sqmm 4 core XLPE insulated armoured and PVC sheathed 1100 Volts grade with aluminium conductor multistranded including cable connecting lugs, glands,jointing materials etc., laid in trenches, floors, roof, ducts and fixing using clamps, saddle for pole, wall including taking down complete all as directed. |
| 14 | Supply and laying in trenches, LT underground cable of size 25 Sqmm 3.5 core XLPE insulated armoured and PVC sheathed 1100 Volts grade with aluminium conductor multistranded including cable connecting lugs, glands,jointing materials etc., laid in trenches, floors, roof, ducts and fixing using clamps, saddle for pole, wall including taking down complete all as directed. |
| 15 | Supply and laying in trenches, LT underground cable of size 35 Sqmm 3.5 core XLPE insulated armoured and PVC sheathed 1100 Volts grade with aluminium conductor multistranded including cable connecting lugs, glands,jointing materials etc., laid in trenches, floors, roof, ducts and fixing using clamps, saddle for pole, wall including taking down complete all as directed . |
| 16 | Supply and laying in trenches, LT underground cable of size 50 Sqmm 3.5 core XLPE insulated armoured and PVC sheathed 1100 Volts grade with aluminium conductor multistranded including cable connecting lugs, glands,jointing materials etc., laid in trenches, floors, roof, ducts and fixing using clamps, saddle for pole, wall including taking down complete all as directed. |
| 17 | Supply and laying in trenches, LT underground cable of size 70 Sqmm 3.5 core XLPE insulated armoured and PVC sheathed 1100 Volts grade with aluminium conductor multistranded including cable connecting lugs, glands,jointing materials etc., laid in trenches, floors, roof, ducts and fixing using clamps, saddle for pole, wall including taking down complete all as directed. |
| 18 | Supply and laying in trenches, LT underground cable of size 95 Sqmm 3.5 core XLPE insulated armoured and PVC sheathed 1100 Volts grade with aluminium conductor multistranded including cable connecting lugs, glands,jointing materials etc., laid in trenches, floors, roof, ducts and fixing using clamps, saddle for pole, wall including taking down complete all as directed . |
| 19 | Supply and laying in trenches, LT underground cable of size 120 Sqmm 3.5 core XLPE insulated armoured and PVC sheathed 1100 Volts grade with aluminium conductor multistranded including cable connecting lugs, glands,jointing materials etc., laid in trenches, floors, roof, ducts and fixing using clamps, saddle for pole, wall including taking down complete all as directed. |
| 20 | Supply and laying in trenches, LT underground cable of size 240 Sqmm 3.5 core XLPE insulated armoured and PVC sheathed 1100 Volts grade with aluminium conductor multistranded including cable connecting lugs, glands,jointing materials etc., laid in trenches, floors, roof, ducts and fixing using clamps, saddle for pole, wall including taking down complete all as directed . |
| 21 | Excavation in trenches not exceeding 1.5 m wide and not exceeding 1.5 m deep for laying of cables, pipes, foundation for poles etc., and getting out in hard/dense soil all as specified and as directed. |
| 22 | Returning filling in excavated soil upto a depth of 30 cm after riddling of excavated soil (in lieu of sand) for cushioning of cable and refilling of trenches with left over normal excavated soil including spreading, leveling, watering and well ramming in layers complete all as specified and as directed . |
| 23 | Removing surplus soil to a distance not exceeding 50 m and depositing where directed at a level not exceeding 1.5 m above the starting point as directed. |
| 24 | Supplying and laying un-reinforced precast concrete cable cover, class LV, Type 1 with peak, size250 mm x 150mm x 40mm all as specified and as directed. |
| 25 | M&L for PCC 1:4:8 type D2 using 40mm graded stone aggregate in foundation complete all as directed by Eng-in-cahrge. |
| 26 | M&L for PCC 1:3:6 type C1 using 20mm graded stone aggregate for stay and coping for poles including necessary form work to exposed surface finished smooth and even all of specified. |
| 27 | Supply and laying GI tubing light grade 50mm dia in trenches/fixing on pole /wall/crossing in drain etc.for protection of UG cable complete all as specified and directed. |
| 28 | Supply and laying GI tubing light grade 80mm dia in trenches/fixing on pole /wall/crossing in drain etc.for protection of UG cable complete all as specified and directed. |
| 29 | Material & Labour for boring of holes under roof, pavement, hardstanding by trenchless technology and necessary machine including GI pipe of 50/80/100mm dia suitable for 0.4mpa working pressure complete all as specified and directed. |
| 30 | Supply and fxing in replacement of 11meter high hot dipped octagonal poles with 130mm bottom dia & 70mm top dia made up of 3mm thick HT Sheet alongwith base plate of size 200x200x12mm including foundation bolts & bracket Suitable for accomodating 04 X Flood lights on ring type bracket of size 40mm pipe alongwith mounting arrangement for flood lights , 'J\\" type foundation bolts and numbering of poles, in white paint over black painted back ground at a height of 1.5m from bottom of pole with 5 cm large bold letters 2\\" (inch) wide with etc complete as required and all as specified and directed.complete accessories as required including dismantling existing pole. |
| 31 | Supply and fix in repair energy saving rectangular LED flood light fitting 200 Watts, 240 volts AC, cool white colour, CCT 5700°K, CRI>70, THD<10%, system lumens not less than 100lumens/watt with innovative thermal management, available with multiple optics, equipped with IP-66 protection, 5 KV surge protection, aluminium die cast housing, life of luminaires should not be less than 50000 burning hours and suitable for large area lighting including fixing on High mast pole/Buildings/TARMAC poles etc. by means of clamps, nuts, bolts and any other accessories complete all as specified and as directed |
| 32 | Supply and fxing in replacement of 7 meter high hot dipped octagonal poles (Grey painted coated) with 130mm bottom dia & 70mm top dia made up of 3mm thick HT Sheet alongwith base plate of size 200x200x12mm including foundation bolts & bracket of size M20x600mm EN 8 grade 'J\\" type foundation bolts and numbering of poles, in white paint over black painted back ground at a height of 1.5m from bottom of pole with 5 cm large bold letters 2\\" (inch) wide with etc complete as required and all as specified and directed.complete accessories as required including dismantling existing pole. |
| 33 | Supply and fxing in replacement of 6 meter high hot dipped steel tubular poles (Grey painted coated) with 130mm bottom dia & 70mm top dia made up of 3mm thick HT Sheet alongwith base plate of size 200x200x12mm including fiundation bolts & bracket of isze M20x600mm EN 8 grade 'J\\" type foundation bolts and numbering of poles, in white paint over black painted back ground at a height of 1.5m from bottom of pole with 5 cm large bold letters 2\\" (inch) wide with etc complete as required and all as specified and directed.complete accessories as required including dismantling existing pole. |
| 34 | Supply and fix in repair LED street light fitting 70/72 Watt 230 V AC outdoor type with high pressure die cast aluminum hosing and heat resistant complete with driver, lamp bracket with impact and corrosion resistant including thermal management in multiple optics with IP-66 protection, CCT 5700K, lumen efficacy not less than 110 lumen/watts complete all as specified and directed . |
| 35 | S& F in repair asthetically designed decorative hot dipped galvanised mild steel step pole of 3 mtrs with grey powder finish window - Plasma cut & Duly chamfered opening window of 300x10mm including taking down existing unserviceable pole and light fitting complete all as specified and directed . |
| 36 | Supply and fix decorative arms in diffrent designs , shaped and lenghts to compliments in EROS LED Post tops and Poles family suitable for Orbit plus S round arm for pole complete all as specified and directed. |
| 37 | Supply and fix new generation IP 65 Post top energy saving envirionmental firendly long life aesthatically designed with good indirect symmetrical light distribution , die cast aluminium landscape luminarie with high power Victoria LED Post top light as light source for LED Light of capacity 20 Watt suitable for pole of dia 76mm complete alll as specfied and directed. |
| 38 | Supply and fixing in replacement, “Lithium based Energy Efficient Integrated Solar Street Light of 40Watt” in rust proof Aluminium housing with Monocrystalline Solar PV Panel of 75W(-0/+4W)Mono , Lithium Battery 12.8V, 42AH(BIS Certified), IP 65, High brightness W-LED(150 Lm/watt) lamp with Aluminum reflector for better light distribution, Color Temperature 6500K +500K, Microcontroller based charge controller cum driver, automatic dimming function( with PIR Motion Sensor), Dusk to Dawn Operation, suitable to working temperature: (-) 5 degree C to (+) 45degree C, Charging time 1 day and Autonomy 2 days with dimming Protections: Short Circuit, overload, Reverse polarity and battery protections. |
| 39 | Supply and fix in repair glow signage boards with base frame made from angle iron and backside form ACP sheet 3mm thick with IP 68 Protection LED module , good quality virgin monomer Acrylic sheet , MES Logo & Southern Command logo in letters with 5 mm sun board channel , including complete wiring and power supply with IP 68 protection , each letter will be made with computer offset for having same letter style and type as approved , complete all as specified and directed. |
| 40 | Material & Labour for hardcore of gauge not exceeding 63 mm of broken stone, deposited, spread and leveled in layers not exceeding 15 cm thick, watered and rammed to a true surface complete all as specified and directed |
| 41 | Material & Labour local sand dry, filling in trenches around under ground cable complete all as specified and directed. |
| 42 | Material & Labour for spreading / filling loose stone aggregate of 40mm graded all as specified and directed |
| 43 | S&F for Framed work such as grills, gratings, etc.. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work incl hung as gates, incl pintle hinges, stops, hand made sliding bolts etc conforming to Fe.290.Gde-E-165, complete |
| 44 | Supply only Chain link MS galvanised fencing, any size or type complete all as specified and directed. |
| 45 | Fixing only chain link fencing including line wires, any mesh, size and type to any type of standards, rails, straining bolts, etc. including provission of binding wire complete all as specified and directed. |
| 46 | Material & Labour for two coats of synthetic enamel paint over a coat of red oxide primer on new steel Surfaces of any description, complete all as specified and directed. |
| 47 | Excavating in post holes (or similar holes) each n exc 0.5 cu. m, getting out, returning, filling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25 cm in soft/loose soil complete all as specified and directed. |
| 48 | Material & Labour precast cement concrete block masonry with solid blocks,exceeding 10 cm in width and setting in mortar 1:4 Type C1 (1:3:6) complete all as specified and directed. |
| 49 | Material & Labour for 15 mm thick cement plaster in CM 1:4, on stone surface finished even and smooth without using extra cement complete complete all as specified and directed. |
| 50 | Preparation of newly plastered surfaces and applying Two coats of cement base paint on walls incl priming plastered and other surfaces with alkali resistant priming paint etc complete all as specified and directed. |
| 51 | Material and lobour for laying DWC (Double wall corrugated ) pipe conforming or IS 16205 (electric cable use) of nominal outer dia 40mm and inner dia 32mm for laying electrical cables under trenches / under road/ wall complete all as specified and directed. Make : Universal /Rax/ Astrol |
AI Tender Summary
Tender Timeline
Sep 25, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedOct 22, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 4 daysOct 30, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 12 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender