Tender For Construction Of Auditorium Hall At Leimayol Arts Centre, Chingamakha, Imphal West, Manipur.
Tender Value
6.22 Crore
Estimated cost
Bid Submission
16 Oct 2026
20 days left
EMD
12.45 Lakhs
Bank guarantee accepted
Document Fee
5000
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Imphal West → Manipur
EMD Exemption
Not Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for Construction Of Auditorium Hall At Leimayol Arts Centre, Chingamakha, Imphal West, Manipur.
BOQ
| Sl. No. | Item Description |
| 1 | EARTH WORK |
| 2 | Earthwork in excavation by mrchanical means (hydraulic excavator)/ manual means over areas (exceeding 30 cm in depth 1.5 m in width as well as 10 sqm on plan ) including getting out and disposal of excavated earth, lead upto 50 mt and lift upto 1.5 m as directed by th engineer in charge. All kind of soil |
| 3 | Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift upto 1.5 m. |
| 4 | Supplying and filling In plinth with sandy soil under floors induding, watering ,ramming consolidating and dressing complete. |
| 5 | CEMENT CONCRETE |
| 6 | Providing and laying cement concrete in foundation and plinth excluding cost of centering and shuttering 1 :4:8 ( 1 Cement: 4 coarse sand : 8 graded stone aggregate 40 mm nominal size) |
| 7 | REINFORCED CEMEN CONCRETE |
| 8 | Boring, providing and installation bored cast-in-situ reinforced cement pile of specified diameter and length below the pile cap M 25 in cement concrete, to carry a safe working load not less than specified, excluding the cost of steel reinforcement but including the cost of boring with casing and/ or bentonite solution and the length of pile to be embeded in the pile cap etc. all completed(Length of the pile for payment shall be measured up to bottom of pile cap) a) 400 mm diameter |
| 9 | Providing and laying in position specified grade of reinforced cement concrete excluding the cost of centering, shuttering, finishing and reinforcement - All work upto plinth level : 1 :1.5:3 (1 cement 1.5 coarse sand : 3 graded stone aggregate 20 mm nominal size) |
| 10 | Reinforced cement concrete work in walls (any thickness), including attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers.abutments, posts and struts etc. up to floor five level excluding cost of centering.shuttering, finishing and reinforcement : 1 :1.5:3 (1 cement 1.5 coarse sand: 3 graded stone aggregate 20mm nominal size). |
| 11 | Reinforced cement concrete work in beams, suspended floors, roofs having slope upto 15° landings, balconies, shelves, chafias, lintels, bands, plain window sills.staircases and spiral stair cases above plinth level upto floor five level, excluding the cost of centering.shuttering, finishing and reinforcement with 1 :1.5:3 (1 cement: 1.5 coarse sand : 3 graded stone aggregate 20mm nominal size). |
| 12 | STEEL REINFORCEMENT |
| 13 | Steel reinforcement for RCC work i/c straightening, cutting, bending, placing in position and binding all complete up to plinth level (a) Thermo-Mechanically Treated bars. |
| 14 | FORM WORKS |
| 15 | Centering and shuttering including strutting, propping etc and removal of form (a) Foundation footings, bases of columns etc. and mass concrete. |
| 16 | Centering and shuttering including strutting, propping etc and removal of form (b)Suspendod floors, roofs,landings, balconres nnd access platform, with water proof ply 12mm th ick |
| 17 | Centering and shuttering including strutting, propping etc and removal of form (c) Columns, Pillars, Piers, Abutments, Posts and Struts. |
| 18 | Centering and shuttering including strutting, propping etc and removal of form (d) Lintels, beams, plinth beams, girders,bressumers and cantilevers. |
| 19 | BRICK WORKS |
| 20 | Brick Work with 1st class common burnt clay F.P.S. (non modular) bricks in foundation and plinth in Cement mortar 1 : 4 (1 cement : r 4 coarse sand) |
| 21 | Half brick masonry with 1st class common burnt clay F.P.S. (non modular) bricks in superstructure above plinth level upto floor V level in Cement mortar 1 : 4 (1 cement : r 4 coarse sand) |
| 22 | WOOD WORKS |
| 23 | Providing wood work In framess of doors, windows, clerestory windows ond other frames,wrought frames ond fixed In position with hold fast lugs or with dash fastner of required dia ond length (hold fast lugs or dash fastner shall be paid for seperately Local best quality Uingthou wood |
| 24 | Providing wood work in frames of false ceiling, ,partitions etc . sawn and put up inposition : Local best quality Tolhao wood |
| 25 | Providing & fixing 25 mm thick plain local quality Uningthou skirting with necessary screws & priming coat on unexposed surface . |
| 26 | Providing and fixing panelled or panelled and glazed shutters for doors, windows and clerestory windows Including ISi markedMS butt hinges bright finished of required size with necessary 18 screws, excluding panelling which will be paid for separately, all complete as per direction of Engineer-in-charge. Local best quality Tolhao wood . 35 mm thick shutters |
| 27 | Providing and fixing ISi marked oxidised M.S.sliding door bolts with screws etc. complete |
| 28 | Providing and fixing ISi marked oxidised M.S. tower bolt black finish, (Barrel type) with a)250x 10 mm |
| 29 | Providing and fixing ISi marked oxidised M.S. tower bolt black finish, (Barrel type) with a)150x 10 mm |
| 30 | Providing and fixing ISi marked oxidised M.S. handles conforming to 15:4992 with a)125mm |
| 31 | Providing and fixing ISi marked oxidised M.S. handles conforming to 15:4992 with a)75mm |
| 32 | Providing and fixing bright finished brass hard drawn hooks and eyes. a)250mm |
| 33 | Providing 40 x 3 mm flat iron hold fast 40 cm long i/ c fixing to frames with 10 mm dia |
| 34 | Providing and fixing ISI marked oxidised M.S. pressed butt hinges with necessary screws |
| 35 | Providing and fixing M.S. grills of required pattern in frames of windows etc. with M.S. flats, square or round bars etc. including priming coat with approved steel primer all |
| 36 | STEEL WORKS |
| 37 | Providing and fixing M.S. fan clamp type-I of 16 mm dia m.S. bar bent to shape with hooked ends in RCC slabs during laying i/ c oainting the expose portion of loops, all per standaed design complete. |
| 38 | Providing & fixing in position collapsible steel shutters with vertical channels 20mm X 10 mm X 2 mm & braced with flat iron diagonals 20 mm X 5 mm sizes with top & bottom rails of T iron 40 mm X 40 mm X 6 mm with 38 mm dia steel pulleys complete with bolts & nuts,locking arrangement, stoppers,handles i/ c applying a priming coat of red lead paint. |
| 39 | Steel work in built up tubular trusses including cutting, hoisting, fixing in position and applying a coat of approved steel primer red oxide zinc chrome primer conforming to IS:2074-1979) welded and bolted including special shape washer etc. complete.Electric resistant welded tube (Conforming to IS:1611-1979) |
| 40 | ROOFING / CEILING |
| 41 | P /F precoated galvanised iron profile sheets (size, shape and pitch of corrugation as approved by Engineer-in-charge) with zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns. Sheet should have protective guard film of 25 microns minimum to avoid scratches during transportation and should be supplied in single length upto 12 metre or as desired by Engineer-in charge. The sheet shall be fixed using self drilling / self tapping screws of size (5.5x 55 mm) with EPDM seal,complete upto any pitch in horizontal/ vertical or curved surfaces, excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required with (a) Precoated galvanised iron profile sheets 0.50 mmthick. |
| 42 | 26 P /F precoated galvanised steel sheet roofing accessories , Zinc coating 120gsm as per IS: 277 in 240mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns using self drilling/ self tapping screws or with polymer coated J or L hooks, bolts and nuts and or G.I. seam bolts and nuts, G.I. plain and bitumen washers complete : i) Ridges plain (500 - 600mm). Precoated galvanised iron profile sheets 0.50 mm thick |
| 43 | P /F at all height false ceiling including providing and fixing of frame work made of special sections, power pressed from M.S. sheet and galvanised with zinc coating of 120 gms/ sqm (both sided inclusive) as per IS : 277 and consisting of angle cleats of size 25mm wide x 1.6mm thick with flanges of 27mm and 37mm, at 1200mm centre to centre, one flange fixed to the ceiling with dash fastener 12.5mm diax50mm long with 6mm dia bolts,other flange of cleat fixed to the angle hangers of 25x25x0.55mm of required length with nuts and bolts of required size and the other end of the angle hanger fixed with intermediate G.I. channels 45x15x0.9mm running at the spacing of 1200mm centre to centre, to which the ceiling section 0.5mm thick bottom wedge of 80mm with tapered flanges of 26mm each having clips of 10.5mm at 450mm centre to centre, shall be fixed in a direction perpendicular to G.I. intermediate channel with connecting clips made out of 2.64mm diax230mm long G.I. wire at every junction, including fixing perimeter channels 0.5mm thick 27mm high having flanges of 20mm and 30mm long, the perimeter of ceiling fixed to wall/ partition with the help of rawl plugs at 450mm centre, with 25mm long drive-all screws @ 230mm interval, including fixing of gypsum board to ceiling section and perimeter channel with the help of dry wall screws of size 3.5 x 25 mm at 230 mm c/ c, including jointing and finishng to a) Fully Perforated Gypsum Plaster Board of size 1200 x 2400 x 12.5 mm having approx. 15% perforated size and pattern as approved by the Engineer-in-charge and as per manufacter's specification, with all 4 sides tapered and backed by acoustical tissue with NRC value not less than 0.60. |
| 44 | FLOORING |
| 45 | 52 mm thick cement concrete flooring with concrete hardener topping under layer 40 mm thick cement concrete 1:2:4(1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) and top layer 12 mm thick cement hardener consisting of mix 1:2 (1 cement . hardener mix: 2 graded stone aggregate 6 mm nominal size) by volumen.hardening compound is mixed @ 2 litre per 50kg of cement or as per manufacturers specifications. This includes cost of cement slurry, but excluding the cost of nosing of steps etc. |
| 46 | Marble stone flooring with 18mm thick marble stone (sample of marble shall be approved by Engineer-in-charge) over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with grey cement slurry including rubbing and polishing complete with : Makrana white second quality. |
| 47 | Marble chips skirting (upto 30 cm height) rubbed and polished to granolithic finish, top layer 6 mm thick with white, black, chocolate, grey, yellow or green marble chips of sizes |
| 48 | FINISHING WORKS |
| 49 | 12mm Cement Plaster of mix 1:4 (1 Cement: 4 Fine Sand) |
| 50 | 15mm Cement Plaster on rough side of single or half brick wall of mix 1:4 (1 Cement: 4 Fine Sand) |
| 51 | Providing and applying white cement based putty of average thickness lmm,of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete. |
| 52 | Applying one coat of water thinnable cement primer of approved brand and manufacture on wall surface : Water thinnable cement primer |
| 53 | Applying ready mixed priming coat pink primer of approved quality on wood work |
| 54 | Painting two or more coats (excluding priming coat) with superior ready mixed paint for wood wo.rk of appioved quality in all shades on new work to give an even shade. |
| 55 | Applying ready mixed priming coat (Red lead primer of approved quality) on steel work. |
| 56 | Painting wood work with Deluxe Multi Surface Paint of required shade. Two or more coat applied @0.90 ltr/10 sqm over an under coat of primer applied @0.75 ltr/ 10 sqm of approved brand or manufacture |
| 57 | Painting with silicon & acrylic emulsion based water thinnable sealer of approved brand and manufacture on wet or patchy portion of plastered surfaces : Two coats |
| 58 | Making plinth protection 50mm thick of cement concrete 1:3:6 (1 cement : 3 coarsesand : 6 graded stone aggregate 20 mm nominal size) over 75mm bed of dry brick ballast 40mm nominal size well rammed and consolidated and grouted with fine sand including finishing the top smooth. |
| 59 | Providing and fixing EchoSeal Premium acoustic wall panels, 25 mm thick, fabric finished, including framework and fixing accessories, complete as per manufacturer's specifications. |
| 60 | Providing and fixing heavy duty homogeneous PVC I vinyl sheet flooring of approved make, shade and pattern, of minimum 2.0 mm thickness, laid over prepared smooth cement · concrete / screed base using approved adhesive, including rolling, cutting, jointing, cleaning and all complete as per manufacturer's specifications. |
| 61 | Cushioned carpet for Auditorium |
| 62 | Push back Auditorium chair with cup holders for VIP's & VVIP's i/c installation charges |
| 63 | Auditorium chair i/ c installationcharges |
| 64 | UNDERGROUND WATER TANK & SEPTIC TANK |
| 65 | EARTH WORK |
| 66 | Earthwork in excavation by mrchanical means (hydraulic excavator)/ manual means over areas (exceeding 30 cm in depth 1.5 m in width as well as 10 sqm on plan ) including getting out and disposal of excavated earth, lead upto 50 mt and lift upto 1.5 m as directed by th engineer in charge. All kind of soil |
| 67 | Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift upto 1.5 m. |
| 68 | CEMENT CONCRETE |
| 69 | Providing and laying cement concrete in foundation and plinth excluding cost of centering and shuttering 1 :3:6 ( 1 Cement: 3coarse sand : 6graded stone aggregate 40 mm nominal size) |
| 70 | REINFORCED CEMENT CONCRETE |
| 71 | Reinforced cement concrete work in beams, suspended floors, roofs having slope upto 15° landings, balconies, shelves, chafias, lintels, bands, plain window sills.staircases and spiral stair cases above plinth level upto floor five level, excluding the cost of centering.shuttering, finishing and reinforcement with 1 :1.5:3 (1 cement: 1.5 coarse sand : 3 graded stone aggregate 20mm nominal size). |
| 72 | Providing and laying in position specified grade of reinforced cement concrete excluding the cost of centering, shuttering, finishing and reinforcement - All work upto plinth level : 1 :1.5:3 (1 cement 1.5 coarse sand : 3 graded stone aggregate 20 mm nominal size) |
| 73 | Reinforced cement concrete work in walls (any thickness), including attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers.abutments, posts and struts etc. up to floor five level excluding cost of centering.shuttering, finishing and reinforcement : 1 :1.5:3 (1 cement 1.5 coarse sand: 3 graded stone aggregate 20mm nominal size). |
| 74 | STEEL REINFORCEMENT |
| 75 | Steel reinforcement for RCC work i/c straightening, cutting, bending, placing in position and binding all complete up to plinth level (a) Thermo-Mechanically Treated bars. |
| 76 | FORM WORKS |
| 77 | Centering and shuttering including strutting, propping etc and removal of form (b)Suspendod floors, roofs,landings, balconres nnd access platform, with water proof ply 12mm th ick |
| 78 | Centering and shuttering including strutting, propping etc and removal of form (a) Foundation footings, bases of columns etc. and mass concrete. |
| 79 | Centering and shuttering including strutting, propping etc and removal of form walls (any thicness) including attached pilasters, buttresses, plinth and string courses etc. |
| 80 | BRICK WORKS |
| 81 | Half brick masonry with 1st class common burnt clay F.P.S. (non modular) bricks in superstructure above plinth level upto floor V level in Cement mortar 1 : 4 (1 cement : r 4 coarse sand) |
| 82 | Brick Work with 1st class common burnt clay F.P.S. (non modular) bricks in foundation and plinth in Cement mortar 1 : 4 (1 cement : r 4 coarse sand) |
| 83 | FINISHING WORKS |
| 84 | 15mm Cement Plaster on rough side of single or half brick wall of mix 1:4 (1 Cement: 4 Fine Sand) |
| 85 | WS/SI WORKS |
| 86 | Providing and fixing G.I. pipes complete with G.I. fittings including trenching and refilling etc. 80mm nominal outer dia pipes |
| 87 | Providing and fixing chlorinated polyvinyl chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings This includes jointing of pipes & fittings with one step CPVC solvent cement, trenching, refilling & tyesting of joints complete as per direction of Engineer in charge- 32 mm nominal outer dia pipes |
| 88 | P /F Motor pump (lH.P) i/ c fitting |
| 89 | Providing and fixing water closet squatting pan (Indian type W .C. pan ) with 100 mm sand cast Iron P or S b·ap, 10 lih·e low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever) conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required: White Vitreous china Orissa pattern W.C.pan of size 580 x 440 mm with integral type foot rest |
| 90 | Providing and fixing white vitreous china pedestal type water closet (European type W.C. pan) with seat and lid, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever), conforming to IS : 7231, with all fittings and fixtures complete, - including cutting and making good the walls and floors wherever required: W.C. pan with ISI markedwhite solid plastic seat and lid. |
| 91 | Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever required: a) White Vitreous China Wash basin size 630x450 mm with a pair of 15 mm C.P. brass pillar taps |
| 92 | Providing and fixing white vitreous china flat back half stall urinal of size 580x380x350 mm with white PVC automatic flushing cistern, with fittings, standard size C.P. brass flush pipe, spreaders with unions and clamps (all in C.P. brass) with waste fitting as per IS : 2556, C.I. trap with outlet grating and other couplings in C.P. brass, including painting of fittings and cutting and making good the walls and floors wherever required : a)Single half stall urinal with 5 litre P.V.C. automatic flushing cistern |
| 93 | Providing and fixing one piece construction white vitreous china squatting plate with an integral longitudinal flushing pipe, white P.V.C. automatic flushing cistern, with fittings, standard size G.I. / PVC flush pipe for back and front flush with standard spreader pipes with fittings, G.I clamps and C.P. brass coupling complete, including painting of fittings and cutting and making good t);le walls and floors etc. wherever required : a)Single half stall urinal with 5 litre P.V.C. automatic flushing |
| 94 | Providing and fixing P.V.C. waste pipe for sink or wash basin including P.V.C. waste fittings complete.Flexible Pipe a) 32 mm dia |
| 95 | Providing and fixing mirror of superior glass ( of approved quality) and of required shape and size witl1 plastic moulded frame of approved make and shade with 6 mm thick hard board backing Rectangular shape 1500x450 mm |
| 96 | Providing and fixing PTMT towel rail complete with brackets fixed to wooden cleats with CP brass screws with concealed fittings arrangement of approved quality and colour. a) 450 mm long towel rail with total length of 495 mm, 78 mm wide and effective height of 88 mm, weighing not less than |
| 97 | Providing and fixing toilet paper holder: C.P. brass |
| 98 | Providing and fixing PTMT liquid soap container 109 mm wide, 125 mm high and 112 mm distance from wall of standard shape with bracket of the same materials with snap fittings of approved quality and colour, weighing not less tl1an 105 gms. |
| 99 | Providing and fixing C.P. brass bib cock of approved quality conforming to IS:8931 : a) 15 mm., nominal bore |
| 100 | Providing and fixing C.P. brass stop cock (concealed) of standard design and of approved - make conforming to IS:8931: a) 15 mm nominal bore |
| 101 | Providing and fixing ball valve (brass) of approved quality, High or low pressure, with plastic floats complete : a) 25 mm nominal bore |
| 102 | Providing and fixing gun metal non- return valve of approved quality (screwed end) : a) 25 mm nominal bore Vertical Code |
| 103 | Cutting holes up to 15x15 cm in R.C.C. floors and roofs for passing drain pipe etc. and repairing the hole after insertion of drain pipe etc. with cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size), including finishing complete so as to make it leak proof. |
| 104 | Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, i/ c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge. Concealed work, including cutting chases and making good the wall etc. a) 32 mm nominal outer di.a Pipes |
| 105 | Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings This includes jointing of pipes & fittings with one step CPVC solvent cement, h·enching, refilling & testing of joints complete as per direction of Engineer in Charge. External work: a) 65 mm nominal outer di.a Pines |
| 106 | Providing and fixing uplasticised PVC connection pipe with brass unions : 30 cm length: 20 mm nominal bore |
| 107 | Providing and placing on terrace (at all floor levels) polyethylene water storage tank, IS : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank. |
| 108 | Electricfication: - |
| 109 | Wiring for light point /Fan point /exhaust Fan point /call bell point with 1.5mm2 PVC insulated copper conductor single core cable in PVC casing & capping with modular type switch, modular plate suitable size G.I box and earthing the point with 1.5mm2 PVC insulated copper conductor single core cable etc. as reqd. |
| 110 | 1. Group A |
| 111 | 2. Group B |
| 112 | 3. Group C |
| 113 | Wiring for light point/power plug with 2 x 4 mm² PVC insulated copper conductor single core cable in PVC casing and capping along with 1 no. 4 mm² PVC insulated copper conductor single core cable for loop earthing etc. as reqd. |
| 114 | Wiring for circuit/sub-main wiring along with earth wire with the following sizes of PVC insulated copper conductor single core cable in PVC casing and capping etc. as reqd. |
| 115 | 1. 2 x 1.5 mm² + 1 x 1.5 mm² earth wire |
| 116 | 2. 2 x 4 mm² + 1 x 4 mm² earth wire |
| 117 | Supply and fixing (following piano type switch / socket) on the existing switch box/cover i/c connection etc as reqd. |
| 118 | 5/6 amps socket outlet |
| 119 | 5/6 amps switch |
| 120 | 15/16 amps socket outlet |
| 121 | 16 amps switch |
| 122 | S/F 400mm dia Wall mounting fan complete with all accessories etc. as reqd. |
| 123 | S/F 380 mm Sweep exhaust fan complete with all accessories i/c connection etc. as reqd. |
| 124 | S/F Star Param Recessed backlit panel round LED 15W Crompton |
| 125 | Supply of Indoor LED par 54 LED Par 200w, voltage 110V-250V/50-60HZ, lamp-TX high power LEDS; 3w X 54 LED, 4 in 1 LED working pot; any safe working position LED display, channel-4/5/7 CHS, Beam Angle-15/25/45/60°, IP Grade-IP20 control mode- master/slave synchronization, DMX-512 control and automatic run function, construction-Aluminium and plastic body, silver, white and black optional. Make: TDH Lighting/DLMC/PLS |
| 126 | Supply of LED cobe par 200W High Quality LED Parcan Light complete with, Lamp source 3200K CCT Colour temperature CRI & TLCI Values above 95DMX 512 dimming with 3 channel control Beam Angle of 9° / 25° / 45° Total Power Consumption of 165W High quality output replacing 1000W Halogen Par Flicker Free 100% for Tv & Film Cameras 11.7KHz Refresh Rate, Linear Dimming 0 ~ 100% Fuse and Internal safety protections Strobe option Adjustable 1-25 times/Sec Variable Fixture provided with Yoke of Manual Adjustment 3 Pin XLR for DMX Black powder coated body. Make: TDH Lighting/DLMC/PLS |
| 127 | Supply of 200W LED Fresnel Light having 3200K colour temperature High quality uniquely designed Fresnel Lens CRI,TLCI and R9 value above 96 LED COB Based Source No Multiple Shadows - Single Source illumination Total Power Consumption of 210W Linear dimming 0 ~ 100% Adjustment Flicker Free for High FPS, Power AC90-260V, 50/60HZ Working Temperature - +40° ~ -30° Active Cooling with Low Noise Fan DMX Control/3pin xlr Black powder coated fabricated housing with normal yoke. Make: TDH Lighting/DLMC/PLS |
| 128 | Supply of LED Spot light 200w Flicker free LED Light Source: 1pcs 200watt COB LED (WW/CW) Zoom: DMX control Lamp average life time: 50,000 hours DMX Channel: 2 / 3 / 4 channel Control Mode: DMX512, software (connect to computer), manual control Dimmer: 100% linearly adjustable Angle: 15°-50° Voltage: AC90-260V 50/60Hz Power: 200W Working Environment: indoor -20°C- 40°C IP Rate: IP20 Make: TDH Lighting/DLMC/PLS |
| 129 | Supply of LED Profile spot 26\\" ULTRA BRIGHT specification Voltage : AC90-240V, 50/60Hz Power Consumption : 200W LED : 200W Warm White / 2 in 1 / 4 in 1 Service Life : 60000 hours Lens Angle : 19/26/36° Optional Dimmer : 0-100% Linearly Adjustable Ambient Temperature : -25°C ~ +45°C Control Signal DMX 512, Master-slave, Sound, AutoControl Channel : 1/3CH Single colour, 2/5CH (2in1) N.W 6 kg, G.W : 7.5KG Dimensions : 450*280*mm Packing Size : 650*300*300mm Make: TDH Lighting/DLMC/PLS |
| 130 | Supply of LED Blinder 4way 4x100w Voltage : AC90V - 245V Frequency : 50-60HzPower Consumption : 450W Light Color : White or warm White LED Control : Individual Controllable Lifetime : 60,000 hours DMX Channel : 6/12/2CHColor Temp : 2500K / 3200K / 6500K Warm White : 5600K - 6400K Cool White : 2800K - 3200K Dimmer : 0~100% Linear Adjustable Beam Angle : 38 Degree Working Temperature : -30°C~50°C Control Mode : DMX512, Master / Salve, Auto Run, Stand alone, Sound Active Strobe Effect : Variable Speed (1-30Hz) House Material : Matel House Color : Black IP Grade : IP20 Weight : 5.5 kg Make: TDH Ligting/DLMC/PLS |
| 131 | Supply of LED cyclorama light Light source : 18PCS 12W 4IN1 LEDs Lens angle : 25°(30°, 45°, 60° optional) Channel mode : 3 / 4 / 6 / 7 / 9DMX Channel mode 0-100% linear dimming function: color mix, automatic color change, built-in program and strobe effect with adjustable Sound controlled via built-in microphone Adjustable sound sensitivity LED display, easy to control Control : auto, sound active, DMX512, software(connect to computer) Overheating protection Voltage : 100-220V,50/60hz Power : 230W IP rating : IP20 Make: TDH Lighting/DLMC/PLS |
| 132 | Supply of Digital Light Controller 1.Independent Intellectual Property Rights, Possessing Appearance Patents, Computer Copyright Registration Certificates. With CE, ROHS and related Test Reports. 2. Linux System, quad-core 64bit ARM processor 3. 4 DMX512 Output, 2048 Channels. Can Expand to 8 DMX512 Output, 4096 Channels 4. Supports Multiple Formats Library: R20, D4 and xml 5. Art-Net Port 6. 10.4\\" TFT-LCD Capacitive Touch Screen 7. Built-in Multiple Language, Support Customized 8.12 Executor faders+8 Preset Faders, 100 Pages. Save MAX 1200 Playback Program, run 20 programs simultaneously. 9. 4 High-precision Photoelectric Encoder Wheels with Backlight 10. With Vector Light Layout Function, Simulating Site Layout and Emission 11. Support for creating workspaces and quickly accessing interface 12. supports naming functions such as text, handwritten graffiti, and outline colors 13.Time code supports internal player, external MIDI, LTC time triggering 14.Built-in music player, compatible with MP3,WAV, FLAC and APE 15.Independent CMY or RGB color mixing system 16.MAX 1000 fixtures and 600 fixture group 17.MAX 600 material and can be classified 18.MAX save 1000 lighting program 19.Support remote software update |
| 133 | Supply of PLS 380W SHARPY with Out of light lens diameter: 155mm, Expected life of lamp bulbs: 2000 hours Color temperature: 7800K, Voltage: AC100-240V 50/60Hz, X-axis/Y-axis: 16-bit precision scanning; photoelectric reset system is used for horizontal and vertical direction of X-axis 540° and Y-axis 270°. Accidental collision error can be automatically retrieved and reset, Color disc: fixed color disc; a total of 13 kinds of colors including white; the two-way rainbow effect can achieve half-color, panchromatic, single and double color gradient and slow motions in positive and negative directions. It also has Hall, magnetic positioning and automatic error correction function. Make: TDH Lighting/DLMC/PLS |
| 134 | Supply of Cable Tray 40 x100 x16swg ited. (Customised) |
| 135 | Supply of Light socket box 4\\"x4\\" with 15 Amp multi socket Anchor/Dimond (Customised) |
| 136 | Supply of Side Light Ladder of 25mm x 50mm M.S tube size (6'x2') Make : Customised |
| 137 | Supply of DMX Splitter 1 in 10 out The XLR Connectors are mounted directly on the board. 2. Connectors can be on the front or on the back. 3. Daisy chain of the input signal. 4. Switch for DMX line termination. 5. In 1 to 10 unit, Make: TDH Lighting/DLMC/PLS |
| 138 | Supply of DMX cable 20/0.12BC+PE1.8, for stage to Control room (PLS/FBT/TASKER) or eq. |
| 139 | Supply of 6mm2 3 core PVC/XLPE insulated heavy duty armoured cable 1.1 KV grade |
| 140 | Supply of Customised MCB box having facility to connect the 58 nos, light point, with 58 Mcb 25Amp & 1 Isolator 100Amp RYB Indicator frequency meter, Volt meter etc. Make: Custom |
| 141 | Supply of DMX point box Make: Custom |
| 142 | Supply of 50mm OD G I Pipe B.Class for lighting grid & lighting bar to be hang from top with support of 40x40x5mm M.S.Angle. (Make:-JINDAL/TATA/) or eq. |
| 143 | Earthing with copper plate 600 mm x 600 mm x 6 mm thick i/c accessories and providing masonary enclosure with cover plate having locking arrangement and watering pipe etc. (but without charcoal or coke and salt) as reqd |
| 144 | Extra for using salt and charcoal for G.I or copper plate earth electrode as reqd. |
| 145 | P/L. earth connection from earth electrode with 4 mm dia copper wire in 15 mm dia G.I. pipe as reqd. |
| 146 | P/F 250 amp. TPN stand ground on load change over switch (Compact design) 415/500 V including connection etc as reqd |
| 147 | Sound System: - |
| 148 | Supply of professional Line Array Speaker System 12\\" two-way) suitable for auditorium sound reinforcement including mounting accessories and rigging hardware. |
| 149 | Supply of 18\\" Subwoofer Speakers compatible with main line array system for low frequency reinforcement. |
| 150 | Supply of Stage Monitor Speakers for stage performers including stand and accessories. |
| 151 | Supply of Digital Audio Mixing Console (minimum 32 channel) with built-in DSP, effects processor and USB interface. |
| 152 | Supply of Professional Power Amplifiers compatible with speaker system including DSP processing. |
| 153 | Supply of Digital Signal Processor / Equalizer / Audio Management System for system tuning and control. |
| 154 | Supply of Wireless Microphone System (handheld/lapel type) complete with receiver. |
| 155 | Supply of Podium Gooseneck Microphones suitable for Lectern installation. |
| 156 | Supply of Audio Equipment Rack with Power Sequencer and Distribution System. |
| 157 | Supply of Professional Audio Cabling, Connectors, Patch Panels and Accessories required for complete installation. |
| 158 | Supply and fixing of Speaker Mounting Hardware, Rigging Frames and Brackets. |
| 159 | Installation of complete sound system including speaker mounting, wiring, termination and testing. |
| 160 | Acoustic tuning, calibration, testing and commissioning of the sound system to ensure uniform sound coverage. |
| 161 | Transportation, insurance, loading/unloading of all equipment to site at Imphal. Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Sep 25, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedOct 16, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 20 daysOct 16, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 20 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender