Tender For special Repair To Bldg No T-57,T-241 And Provn Of Covered Shed Over The Or Bathing Point,01 X Guard Room With Att Toilet/Bathroom , Toolsand Expense Store At Along Mil Stn Under Ge 872 Ews
Tender Value
47.54 Lakhs
Estimated cost
Bid Submission
19 Oct 2026
18 days left
EMD
95100
Bank guarantee accepted
Document Fee
500
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
West Siang → Arunachal Pradesh
EMD Exemption
Not Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for special Repair To Bldg No T-57,T-241 And Provn Of Covered Shed Over The Or Bathing Point,01 X Guard Room With Att Toilet/Bathroom , Toolsand Expense Store At Along Mil Stn Under Ge 872 Ews
BOQ
| Sl. No. | Item Description |
| 1 | Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing) and disposal of debris and rubbish complete all as specified and directed. |
| 2 | Demolition of un-reinforced cement concrete in ground floors and pavings n.exc 15cm thickness, (Below or above Ground level) and disposal of debris and rubbish to a distance complete all as specified & directed. |
| 3 | Demolition of brick work or stone masonary built in cement mortor including all quoins & jambs etc. complete all as specified and directed. |
| 4 | Dismantling Timber Scantlings, 40 Sqcm and over in Section, in any Position, in Unframed Work, complete all as specified and as directed. |
| 5 | Taking down chowkats or frame, n.exc 1.5 Sqm each with shutters (without taking off shutter from the frame) complete all as specified and directed. |
| 6 | Taking down chowkats or frames, exc 1.5 but n.exc. 4 Sqm in each with shutter (without taking off shutter from the frame) complete all as specified and directed. |
| 7 | Taking down cement plaster on brick or stone walls etc including racking out joints, hacking for key, scrubbing down with water and removing rubbish complete all as specified and directed |
| 8 | Dismantling of plain or corrugated steel sheeting, any gauge, thickness, in roof covering including ridges and keeping serviceable sheets in safe custody for reuse in the work complete as directed. |
| 9 | Dismantling of wrought iron or mild steel work of any description not otherwise provided for complete all as specified and directed. |
| 10 | Dismantling Wall and ceiling boards (fibre, pulp, insulation, etc.) or insulation boards/slabs/ blankets, any thickness, including cover fillets/ snap grid frame etc complete all as specified and directed. |
| 11 | Surface excavation not exc 30cm deep and avg 15 cm deep and getting out in soft/loose soil complete all as specified and as directed. |
| 12 | Excavation in trenches, not exceeding 1.5 M wide and not exceeding 1.5 M depth for foundation, trenches for shafts, wells, cesspits, manholes, pier holes, cable etc. n exc 10sq m on plan and n exc 1.5m in depth and getting out in soft/loose soil complete all as specified and directed. |
| 13 | Excavating in post holes (or similar holes) each n. exc. 0.5 cum, getting out returning, filling in and ramming earth or broken rubble mixed with earth around, in layers n. exc. 25 cm watering and removing surplus soil to distance n. exc 50 m and making good surface complete all as specified and directed. |
| 14 | Excavating over areas, n exc 1.5 m deep and getting out as in Soft/Loose Soil, complete all as specified and as directed. |
| 15 | Excavating over areas, exc 1.5 m deep but n exc. 3.00 and getting out as in Soft/Loose Soil, complete all as specified and as directed. |
| 16 | Returning, filling in, including spreading, levelling, watering and well ramming in layers not exc 25 cm as in soft/loose soil complete all as specified and directed. |
| 17 | Removing excavated material not exc. 50 m and depositing where directed at a level not exc 1.5 m above the starting point complete all as specified and directed. |
| 18 | M & L for Sand filling under floors or in foundations including spreading, levelling, watering and consolidation complete all as specified and directed. |
| 19 | M&L Hardcore (broken stone or boulders) of gauge n exc. 63 mm, deposited, spread and levelled in layers n exc. 15 cm thick, watered and rammed to a true surface complete all as specified and directed. |
| 20 | M & L for Plain cement concrete 1:3:6, type C-2 (using 40 mm graded stone aggregate) as in foundation, filling and mass concrete, etc complete all as specified and directed. |
| 21 | M & L for Plain cement concrete 1:4:8, type D-2 (using 40 mm graded stone aggregate) as in foundation, filling and mass concrete, etc complete all as specified and directed. |
| 22 | M & L for Plain cement concrete 1:3:6, type C-1 (using 20 mm graded stone aggregate) as in bed blocks for fixing hold fasts etc. complete all as specified and directed. |
| 23 | M & L for precast cement concrete (1:2:4) type B1 (using 12.5mm graded stone aggregate) setting in CM 1:6 work for in landings, cover slabs (for man holes etc.) chullah hoods, chajjas, water troughs, mangers, shelves and similar articles with plain faces,complete all as specified & directed. |
| 24 | M & L Reinforced Cement Concrete 1:2:4, Type B-1(nominal design mix (20mm graded crushed stone aggregate) as in Slab supported on Walls, complete all as specified and as directed. |
| 25 | M & L Reinforced Cement Concrete 1:2:4, Type B-1(nominal design mix (20mm graded crushed stone aggregate) as in Chajjas , complete all as specified and as directed. |
| 26 | M & L Reinforced Cement Concrete 1:2:4, Type B-1 (Nominal Mix) (using 20 mm graded stone aggregate) for columns ,pillars ,Piers ,posts and struts complete all as specified and directed. |
| 27 | Material and Labour RCC (Nominal mix) 1:2:4 ( Using 20 mm graded crushed stone aggregates) as in Foundations, including rafts, footings, foundation beams; plinth beams; bases for columns, etc.; basement slabs, under-reamed piles and mass concrete complete all as specified and directed. |
| 28 | M & L Reinforced Cement Concrete 1:2:4, Type B-1 (Nominal Mix) (using 12.50 mm graded stone aggregate) as in beams, cantilevers, lintels over 1.5m span complete all as specified and directed. |
| 29 | M&L for 40mm thick damp proff course to horizontal or vertical surfaces in cement concrete 1:2:4, type B-0 using 12.5mm graded stone aggregate including necessary formwork , complete all as specified and directed. |
| 30 | M & L for Pre-cast cement concrete 1:3:6, type C-1 (using 20mm graded stone aggregate), block masonry with solid blocks of size 300x200x200mm or 300x200x100mm, having compressive strength of not less than 100 Kg/Sq Cm (As per IS-2185) exc. 10 cm in width and setting in mortar 1:6 complete all as specified and directed. |
| 31 | M&L Use and waste of Formwork to sides of Pillars, Posts, Struts, Piers, Columns and stanchions, flat, rough finished surfaces of concrete, ( complete all as specified and as directed. |
| 32 | Formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams; and similar work; vertical or to batter all as specified & directed |
| 33 | M&L Use and waste for Formwork to Sides and Soffits of Floor or Roof Beams, Beam Haunchings, Girders, Bres-Summers, Lintels, Cantilevers, Shelves including supports, overhangs, etc. also splays between floors and beams, etc., flat, rough finished surfaces of concrete, complete all as specified and as directed. |
| 34 | M&L Formwork to Chajjas and Similar Items including edges, flat, rough finished surfaces of concrete, complete all as specified and as directed. |
| 35 | M&L Steel windows with frame ,top hung shutter including hinges, steel peg stay, complete with glazing bars ,dovetailed or welded complete all as specified and as directed. |
| 36 | M&L Steel windows with frame ,top hung shutter including hinges, steel peg stay, complete without glazing bars ,dovetailed or welded complete all as specified and as directed. |
| 37 | S&F 35mm thick Flush shutters, solid core construction, with block board core and plywood face panels, commercial type on both sides fitted to cowkhats complete all as specified and directed. |
| 38 | S&F for 2nd class hardwood 35mm thick Glazed and skeleton shutters, open rebated and prepared to receive glass, gauze, etc. (without sash bars), edges of framing plain, chamfered or rounded. fitted with cut and mitred beads for securing glass, etc.; sizes of members of shutters as specified in SSR Part I, Section 8, clause 8.24 (a); supplied and fitted to chowkats as specified in SSR Part-I 2009.complete all as specified and directed |
| 39 | M & L for 6mm thick plywood grade BWR, type BB fixed with screws to timber frame work in wall , complete all as specified and as directed. |
| 40 | S&F for Solid PVC Door Frame of size 50mm x 47mm made out of 5mm wood grain printed PVC sheet reinforced with M.S. Square tube, fixing in opening as per Specifications and Drawings shown in MES Schedule Part-II, complete all as specified and as directed. |
| 41 | S&F Plain Colour Factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, suppling & fixing in the frame at site as per specification & drawing etc complete all as specified and as directed. |
| 42 | S & F in repair Stainless steel wire cloth. 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples complete all as specified and directed. |
| 43 | S & F Stainless steel wire cloth. 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples complete all as specified and directed. |
| 44 | S & F 5.5 mm thick, sheet glass, ordinary quality and glazing with oil putty in square not exceeding 0.5 Sqm in each pane complete all as specified and as directed. |
| 45 | S & F 4 mm thick, sheet glass, ordinary quality and glazing with oil putty in square not exceeding 0.5 Sqm in each pane complete all as specified and as directed. |
| 46 | S & F 4 mm thick, sheet glass, ordinary quality and glazing with oil putty in square exceeding 0.5 Sqm in each pane complete all as specified and as directed. |
| 47 | S & F 100 mm long, stainless steel butt hinges fixed with stainless steel hinge pin etc complete all as specified and directed. |
| 48 | S & F 75 mm long, stainless steel butt hinges fixed with stainless steel hinge pin etc complete all as specified and directed. |
| 49 | S & F 150 mm long, Aluminium anodised, barrel tower bolts of extruded section complete all as specified and directed. |
| 50 | S & F 150 mm size, extruded Aluminium alloy handles, fabricated type, anodised complete all as specified and directed. |
| 51 | S & F 300 mm Aluminium alloy anodised sliding door bolt with hasp & staple (bolt type) and fixing clipes of sheet, cast or extruded sections and fixing bolts of extruded sections or cast aluminium alloy, length of bolt complete all as specified and directed. |
| 52 | S & F 150 mm Aluminium alloy anodised sliding door bolt with hasp & staple (bolt type) and fixing clipes of sheet, cast or extruded sections and fixing bolts of extruded sections or cast aluminium alloy, length of bolt complete all as specified and directed. |
| 53 | S & F Pre-Painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as per manufacturer's instruction complete all as specified and directed. |
| 54 | S & F Pre-Painted galvalume aluminum zinc coating GI based Plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in ridges/vally gutter, fixed with self tapping screws as per manufacturer's instruction complete all as specified and directed. |
| 55 | M&L Mild Steel Work in Tubular Trusses including special shaped washer etc. complete using ERW or induction butt welded tubes conform-ing to IS:1161-1979 grade St.-240, complete all as specified and as directed. |
| 56 | M&L Rolled mild steel section as in main and cross beams, hip and jack rafters; purlins where connected to common rafters and running rails and guides for sliding doors; fixed with angle cleats or other connecting plates conforming to Fe-410-W (Gde-E-250) quality A complete all as specified and directed. |
| 57 | S & F Roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats etc conforming to Fe-290(GDE E 165) complete all as specified & directed. |
| 58 | M&L Framed Work such as hung as gates including pintle hinges,stops, hand-made sliding bolts etc ,Grills, Gratings. with ends of Bars shouldered and/or riveted, or forged into Spikes; Framed Guard Bars; Barred Iron Doors; Ladders; Framed Balusters; Walk Ways; Railings; Framework of Water Tanks and Similar Work, conforming to Fe-290, Gde-E-165, complete all as speci-fied and as directed. |
| 59 | Framed work as in doors or gates of angle or other section with gusset plates, rails, braces, etc., complete, drilled for fixing of steel sheeting or other covering. Doors, etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering, running rails and guides) and hanging; also fastening and fixing complete conforming Fe-290(GDE E 165), complete all as specified & directed. |
| 60 | M & L Rolled sections as in iron chowkats ,framing for cladding, glazing and the like fixed with angle cleats and connecting plates, etc.(Grade Fe 290 E165) all as specified & directed. |
| 61 | M & L mild steel work as in holdfasts , knee pieces and similar small article conforming to Fe-290 Gde-E-165, complete all as specified & directed. |
| 62 | S&F Mild Steel Plates (plain or chequered) channels, square cut or notched (ordinary and counter sunk) forming holes, without any attachment (Fe-290 Gde-E165) complete all as specified and directed. |
| 63 | M&L Mild Steel Screw Bolts (machine made) 11mm to 15mm diameter of neck and length of bolt exc 22.5 Cm and not exc. 30 Cm with hexagonal or square heads at one end and screwed the other, or screwed both ends, each screwed end to be fitted with washers and one hexagonal or square nut, complete all as specified and as directed. |
| 64 | S & F high strength TMT steel bars 10 mm dia., and over cut to length, bend to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia or securing with clips quality complete all as specified and directed. |
| 65 | S & F high strength Mild steel TMT bars 5mm dia and over upto and including 8mm dia in strirrups, spacers and binders spirally for hooping for columns, hooking ends and binding with mild steel wire (annealed) not less than 0.9 mm dia or securing with clips etc complete all as specified and directed. |
| 66 | S & F aluminium Anodised snap grid frame work of size 605mm x 605mm frame work for ceiling with aluminium T section of size 38mm x 25mm x 1.5mm thick for main runners, 25x25x1.5mm thick for cross runner and angle size 25x25x1.5mm thick alongwith wall suspended and including Hangers 4 mm dia. G.I. (upto 1200mm length) adjusting level fixed to ceiling members in proper position, fixed with aluminium staple on snap grid as per manufacturer's instructions including 6 mm thick non asbestor E-board, HSPC, designer fixed to frame complete all as specified and directed by the Engr-in-Charge. |
| 67 | M & L for 25 mm thick, plain cement concrete 1:2:4, type B-0 (using 12.5 mm graded stone aggregate) as in flooring, etc and finished the surface even and smooth without using extra cement complete all as specified and directed. |
| 68 | M & L for 40 mm thick, plain cement concrete 1:2:4, type B-2 (using 20 mm graded stone aggregate) as in flooring, etc and finished the surface even and smooth without using extra cement complete all as specified and directed. |
| 69 | M & L 75 mm thick cement concrete 1:4:8 type D-2( using 40 mm graded stone aggregate0as in sub base for receving the floors finishes. |
| 70 | M & L 100 mm thick cement concrete 1:3:6 type C-2( using 40 mm graded stone aggregate0as in sub base for receving the floors finishes. |
| 71 | M & L for 75 mm thick, plain cement concrete 1:3:6, type C-2 (using 40mm graded stone aggregate) as in plinth protection etc, finishing cement concrete surface even and smooth without using extra cement including making joints with bitumastic filing in proportion of bitumen and sand 1:2 complete all as specified and directed. |
| 72 | M & L for non skid ceramic, coloured tiles 7 to 8 mm thick (square/rectangular) area of each tile exc 0.11sqm but n.exc 0.18 sqm, in floors etc, and set & jointed in neat cement slurry and pointed in white or coloured cement to match with the shade of tiles including 15 mm thick screed bed in cement mortor 1:6 complete all as specified and directed. |
| 73 | M&L Glazed Ceramic Coloured Tile 450 x 350 x 7.0mm thick on Vertical Surfaces such as Skirting, Dados, Risers to Steps, etc., Set and Jointed in Neat Cement Slurry and Pointed in White or Coloured Cement to match the Shade of the Tiles over and including 10mm thick backing layer in cement mortar (1:4) complete all as specified and as directed. |
| 74 | S&F Machine cut kota stone slab flooring 20-25mm thick laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and granite finish polishing complete over 20mm thick 1:6 cement mortar screed bed complete all as specified and as directed. |
| 75 | M & L for Chequered cement concrete tiles of size 20cm x 20cm x 25mm thick, as in floors etc, including 15 mm thick screed bed in cement mortar 1:6 and set & jointed in neat cement slurry and pointed in grey cement and pigments to match with the shade of tiles complete all as specified and directed. |
| 76 | M&L 15 mm thick rendering in cement mortar (1:4) on fair faces of brick or concrete external surfaces in two layers ( 10mm+5mm thick) finished even and smooth without using extra cement using water proofing compound on top layer @2% by weight of cement or as per manufactures instruction on external wall surface complete all as specified and directed.Note : WPC shall be measured and paid seperately |
| 77 | M&L Rendering 10mm thick in Cement Mortar 1:6 on Brick Walls or on Concrete Surfaces, finishing plastered surfaces Even and fair without using Extra Cement complete all as specified and as directed. |
| 78 | M&L Rendering 15 mm thick in Cement Mortar 1:6 on Brick Walls or on Concrete Surfaces, finishing plastered surfaces Even and fair without using Extra Cement complete all as specified and as directed. |
| 79 | M&L Rendering 15mm thick in Cement Mortar 1:4 on Brick Walls or on Concrete Surfaces, finishing plastered surfaces Even and fair without using Extra Cement complete all as specified and as directed. |
| 80 | M & L for neeru finish to plastering all as specified & directed. |
| 81 | S & F water proofing compound (as approved), conforming to IS : 2645-2003, complete all as specified & directed. |
| 82 | M & L for Preparation of newly plastered surfaces of walls and applying two coats of cement base paint over a coat of alkali resistant primer complete all as specified and directed. |
| 83 | M & L for Preparation of old plastered surfaces of walls and applying one coats of cement base paint complete all as specified and directed. |
| 84 | M&L Preparing new Surfaces of wall and applying Three Coats of White Wash, complete all as specified and as directed. |
| 85 | M&L for Preparation applying two coats of oil emulsion distemper (any colour/tint) over a coat of 3 mm thick wall putty on plastered surfaces , preparatory to distempering over on new or old undecorated wall surface smooth and even including preparation of surfaces complete all as specified and directed. |
| 86 | M & L for Preparation of new steel surfaces of any description, over 10 cm in width or girth, not otherwise described and applying two coats of synthetic enamel paint over a coat of red oxide, zine chrome primer complete all as specified and directed. |
| 87 | M & L for Preparation of old painted steel surfaces of any description, not otherwise described, over 10 cm width or girth and applying one coat of Synthetic enamel paint complete all as specified and directed. |
| 88 | M&L preparation of new or previously untreated wooden surface of any description not otherwise described over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified and directed. |
| 89 | M&L preparation of old wooden surface of any description not otherwise described over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified and directed. |
| 90 | S & F in repairs, 15 mm bore, pillar taps, fancy type, cast copper alloy, chromium plated with capstan heads, screwed down high pressure with or without lettered 'Hot or Cold' with long screwed shanks and fly nuts, screwed for iron pipe complete all as specified and directed. |
| 91 | S & F in repair 15 mm bore, Stop/angle valves, cast copper alloy, chromium plated, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions complete all as specified and directed. |
| 92 | S & F 15 mm bore, bib taps, fancy type, cast copper alloy, chromium plated with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule fixed in repair complete all as specified and directed. |
| 93 | S&F Rotational Moulded Polyethylene (HDPE) Water Storage Tank 1000 Litre Capacity (Cylindrical Vertical with Closed Top), Black in Colour, Three Layered Construction, hoisted and fixed in Position all specified in MES Schedule Part-I including provision of 25mm x 100mm GI nippples with check nuts for inlet, outlet wash and overflow pipe including 20 mm bore, Ball valves high pressure of PTMT with epoxy coated Aluminium rod & high density plastic ball screwed for iron pipe and including Lowering of old/unserviceable Water Storage Tank of any description, complete all as specified and as directed. |
| 94 | Supply and fixing in repair 10 litre capacity low level PVC flushing cistern (any colour), syphonic action type, with inlet, ball valve, float, handle, fixed with cast iron bracket (of suitable size) and providing 32 mm dia PVC flush pipe and making all necessary connections complete as directed. |
| 95 | Supply and fix in repairs Vitreous China squatting pan of ‘Orissa pattern’, size 580 mm x 440mm (white) with ‘P’ or ‘S’ trap, front or back inlet and foot rests, any pattern complete including provision of PCC bedding and connection to trap, and to flushing pipe, antisyphonage pipe, etc. complete including making good to floor all as specified and directed. |
| 96 | S&F PVC connection 15mm size with PTMT nut of length 450mm complete all as specified and directed. |
| 97 | S&F Brass chromium plated tubular towel rail, 20mm dia, D type, 60,cm long between flanges as in repair complete all as specified and directed. |
| 98 | S & F in repair 600mmX450mm bevelled edge mirror of selected quality glass, mounted on 6mm thick AC building board or commercial plywood and fixed to wooden plug with chromiun plated brass screws and cup washers complete all as specified and directed. |
| 99 | S&F 20 mm dia Fancy type, Chromium Plated colour coated ( any coloured) curtain rod fixed to bracket/ pelmet box complete all as specified and as directed. |
| 100 | S & F work in repair for ABS body chrome plated shower rose 125mm size including fixing to steel pipe or union complete all as specified and directed |
| 101 | S & F steel tubing of 15 mm bore medium grade including fittings fixed to wall/concealed in wall , ceiling laid in floors etc complete and making good the area to match with existing surface complete all as specified & directed. |
| 102 | S & F steel tubing of 20 mm bore medium grade including fittings fixed to wall/concealed in wall , ceiling laid in floors etc complete and making good the area to match with existing surface complete all as specified & directed. |
| 103 | S & F High density polyethylene pipes (HDPE) 50 mm dia of pressure rating 6 kgf/cm2 fixed complete to walls, ceilings or in floors etc.complete all as specified & directed. |
| 104 | S & F in repair 20 mm bore, gun metal Gate valves, with iron wheel head, Class-I, Pressure Tested of 1.5 Mpa, screwed both ends for iron pipe complete all as specified and directed. |
| 105 | S & F in repair 15 mm bore, gun metal Gate valves, with iron wheel head, Class-I, Pressure Tested of 1.5 Mpa, screwed both ends for iron pipe complete all as specified and directed. |
| 106 | M & L for PCC 1:3:6 type C2 (using 40 mm graded stone aggregate) Concrete bed to drain pipes including packing under, and haunching against the sides of pipes after they are laid and tested for 110 mm dia outer pipes all as specified & directed. |
| 107 | S & F 75 mm bore, PVC (SWR), Soil, waste and vent pipes, single socketed in any length with rubber ring joints fixed to walls, etc complete all as specified and directed. |
| 108 | S&F PVC (SWR) Soil, Waste and Ventilating Pipe 110mm bore (dia), single socketed, in any length with Rubber Ring Joints fixed to Walls, complete all as specified and as directed. |
| 109 | S & F 75 mm bore, PVC (SWR) bends of any radius complete all as specified and directed. |
| 110 | S & F 75mm bore, PVC (SWR) junction single, (Single T) equal or unequal complete all as specified and directed. |
| 111 | S & F 110mm bore, PVC (SWR)Vent Cowl,complete all as specified and directed. |
| 112 | S&F PVC(SWR) Floor Trap with 75 mm bore (dia) Outlet, with Gratings including jointing to Waste Pipe and fixed in Cement Concrete 1:2:4 (20mm graded aggregate), as in repair complete all as specified and as directed. |
| 113 | S&F Vitreous China Wash Hand Basin Pedestal type 550x400mm in size, White (Flat Back or Angle Back Type) with 32mm dia Brass Chromium Plated Waste Fitting, a pair of Cast Iron Brackets duly painted including Cutting and pinning in Ends, making good disturbed Surfaces in Cement Mortar 1:3 including taking down/out unserviceable Wash Hand Basin and connected Items, complete all as specified and as directed. |
| 114 | Taking down copper/aluminium point wiring (light, fan, socket or power) complete, including fixture and fittings such as switches, ceiling roses, pendants, regulators, sockets, light fitting etc. removing materials to store for keeping in safe custody or for taking credit (credit for above items should be made as per conditions separately) and making good disturbed surfaces of walls, floors, etc. complete all as specified and directed. |
| 115 | Taking down unserviceable main switches, DBs, bus bars chambers, VTPN etc any capacity including all fittings and fixtures such as MCBs, isolator, etc and removing from site complete all as specified and directed. |
| 116 | M & L for Point wiring for one light/exhaust fan/fan point/call bell controlled by one way switch with two runs of single core 1.5 Sq.mm. (Nominal area) PVC insulated unsheathed multistranded copper conductor cable FRLSH (ISI marked) drawn through and including non metallic PVC casing capping (ISI marked) (aprox size 20/25/40mm width) surface type with all fittings/fixtures such as Tee, Bend, elbow, socketr, shaddle etc including 1.5mm thick MS sunken/terminal box including 3mm thick backelite sheet cover for fixing flush type switches, sockets, regulators etc. including provision of multistranded 1.5 Sq.mm copper conductor cable FRLSH [ISI marked] as earth wire connected to common earth dolly and earth in distribution board complete all as specified and as directed.(Note.: (i) The rate quoted is deemed to include making good the disturbed sufaces and to match the adjoining surface.) |
| 117 | All as per item No. 116.00 above but for One 3/5 pin socket outlet 6 amps point on same board complete ditto , all as specified & directed. |
| 118 | All as per item No. 116.00 above but for One 3/5 pin socket outlet 6 amps on independent board complete ditto ,all as specified & directed. |
| 119 | All as per item No. 116.00 here in before but for one 15 Amps power point on the independent board with two runs of PVC insulated and unsheathed copper conductor cable of size 2.5 sqmm multistranded FR (ISI marked) and 2.5 sqmm PVC insulated unsheathed solid copper conductor cable FR (ISI marked) as earth lead complete ditto,all as specified & directed. |
| 120 | S & F Modular switch one way 6 Amp 240 volts, 1 module ,240 volt AC and connecting up ,complete all as specified and as directed. |
| 121 | S & F Modular Socket outlet 2 in 1, 3 pin, 5/6 Amps, flush type complete all as specified and as directed. |
| 122 | S & F Modular Switch socket combination 2 in 1, 3 pin, 6 Amp, flush type, universal complete all as specified and as directed. |
| 123 | S & F Modular Switch socket combination 2 in1, 3 pin, 6 and 16Amp, flush type, universal complete all as specified and as directed. |
| 124 | S & F Modular fan step regulator,120W-2 module, 240 volt and connecting complete all as specified up ,complete all as specified & directed. |
| 125 | S & F ceiling rose, 65 X 50mm two to three terminals, PVC/polycarbonate, insolated body complete all as specified and directed. |
| 126 | S & F Angle Holder/Lamp Holder , PVC /polycarbonate type with backplate including LED Bulb , 15 watts , B-22 Lumen ≥ 900, Luminous afficancy ≥ Lum/watt, CCT: WW/NW/CW, CRI > 80 Ra , IP20 rated ,overmounted plastic housing, polycarbonate diffuser , 4 KV surge protection with over Voltage protection withstand upto 440 V (for 10 minute) with open and short circut protections as per IS :16102 complete all as specified & directed. |
| 127 | S & F LED Bulb 15 watt complete all as specified & directed. |
| 128 | S & F LED Bulb 18 watt complete all as specified & directed. |
| 129 | S & F LED Bulk Head, 10 Watt, IP 65 rated, compact design, PC Co extruded with high energy saving with all accessories and connecting up including lamp complete all as specified and directed. |
| 130 | S & F LED tube light fittings, retro bar professional WH 5700K to 6000K, 20 Watt and 2000 Lumens of cool white with all accessories, internally prewired and connecting up with twin core twisted copper conductor cable of suitable size including tube lamp complete all as specified and directed. |
| 131 | S & F Exhaust fan, 300 mm sweep, heavy duty, metal body 1400 RPM, AC, single phase, complete with all accessories and louver and electric connection including making necessary holes in walls complete all as specified and directed |
| 132 | S & F ceiling fan, complete with blades , down rods , electronic regulator and accessories 230 V ,1400 mm sweep , min air delivery 245 CFM with service valve 6.00 BEE , five star rated with brushless direct current motor BLDC , complete all as specified and directed |
| 133 | S & F sheet metal enclosure for DB's when MCBs to be used 4-way, SPN 240 V, Double door with IP 43 protection epoxy based powder coated suitable for mounting MCB DP/SPN as incomer and MCB SP as out -goings with 200 amps rated Bus-bar , neutral Bar, earth bar, connecting cable links and connecting up , including taking down unserviceable sheet metal enclosure of any description ,complete all as specified and as directed. |
| 134 | S & F sheet metal enclosure for DB's when MCBs to be used 8-way, SPN 240V, Double door with IP 43 protection epoxy based powder coated suitable for mounting MCB DP/SPN as incomer and MCB SP as out -goings with 200 amps rated Bus-bar , neutral Bar, earth bar, connecting cable links and connecting up , including taking down unserviceable sheet metal enclosure of any description ,complete all as specified and as directed. |
| 135 | S & F sheet metal enclosure for DB's when MCBs to be used 12-way, SPN 240V, Double door with IP 43 protection epoxy based powder coated suitable for mounting MCB DP/SPN as incomer and MCB SP as out -goings with 200 amps rated Bus-bar , neutral Bar, earth bar, connecting cable links and connecting up , including taking down unserviceable sheet metal enclosure of any description ,complete all as specified and as directed. |
| 136 | S & F MCB SPN 40-63A Amps, 240 Volts, 10KA, C Curve complete all as specified and as directed |
| 137 | S & F MCB SP 6 to 32 Amps, 240 Volts, 10KA, C Curve, complete all as specified and as directed |
| 138 | S & F Isolator TPN 415 volt .63 Amps complete all as specified and as directed |
| 139 | Supply and laying XLPE insulated,screened PVC bedded. galvanized steel strip or wire armoured , electric power cables (heavy duty) with stranded aluminium conductor , 1100 volts grade of size 16 mm sqmm x 2 core including taking out /removing the existing old/unsv cable complete all as specified & directed, |
| 140 | Supply and laying XLPE insulated,screened PVC bedded. galvanized steel strip or wire armoured , electric power cables (heavy duty) with stranded aluminium conductor , 1100 volts grade of size 25 mm sqmm x 3.5 core including taking out /removing the existing old/unsv cable complete all as specified & directed, |
| 141 | Supply & fixing /Laying Galvanised steel water tubing (medium grade) ,ISI marked with all new GI fittings and fixed to wall and ceilings or laid in floors etc. of size 25 mm dia , complete all as specified & directed. |
| 142 | Supply & fixing /Laying Galvanised steel water tubing (medium grade) ,ISI marked with all new GI fittings laid in trenches etc. of size 40 mm dia , complete all as specified & directed. |
| 143 | Supply & fixing /Laying Galvanised steel water tubing (medium grade) ,ISI marked with all new GI fittings laid in trenches etc. of size 25 mm dia , complete all as specified & directed. |
| 144 | Supply and fix in repair Gun metal, globe or gate valves (ISI marked) ( Class-I) with iron wheel head, screwed both ends for 25 mm bore GI pipe including taking down old unserviceable one complete as specified and as directed |
| 145 | S & F Ball Brass valves,high pressure with polythene float anf fly nut complete for brass ferrule of size 25 mm bore dia ,complete all as specified & directed. |
| 146 | Materials and Labour Cutting existing road / path etc for taking out cable and proction pipe and making good the disturbed surfaces with cement concrete type C2 ( 1:2:4,) using 20mm graded crushed stone aggregates) of suitable depth complete all as specified & directed. |
| 147 | Materials and Labour Cutting existing PPR/Steel tubing for alterations or additionsif necessary done , in any position without taking down of size upto 50 mm dia bore , complete all as specified & directed. Please Enable Macros to View BoQ information |
| 148 | Materials and Labour Cutting existing PPR/Steel tubing for alterations or additionsif necessary done , in any position without taking down of size upto 50 mm dia bore , complete all as specified & directed. Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Sep 25, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedOct 19, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 18 daysOct 21, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 20 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender