Tender For Special Repair To Bldg No P-69 At Jak Li Regt Centre Under Ge 970 Ews
Tender Value
40.94 Lakhs
Estimated cost
Bid Submission
14 Oct 2026
10 days left
EMD
82000
Bank guarantee accepted
Document Fee
500
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Budgam → Jammu and Kashmir
EMD Exemption
Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender For Special Repair To Bldg No P-69 At Jak Li Regt Centre Under Ge 970 Ews
BOQ
| Sl. No. | Item Description |
| 1 | Demolation of Brickwork or stone powder Masonry, built in cement or lime mortar including all quoins, arches, pillars, etc, but excluding ashlar facings, dressed stonework and precast concrete complete all as specified and directed. |
| 2 | M&L for brick work with sub class `B’ bricks, straight or curved on plan exc 6m mean radius built in CM 1:6 complete all as specified and directed. |
| 3 | M&L Walling of random rubble stone masonry, uncoursed, well bonded bedded & hearted , built in cement mortar 1:4 in retaining walls, abutments and similar work complete all as specified and as directed |
| 4 | M&L Raking out joints/ pointing to squared rubble stone masonry, coursed or uncoursed built in cement or cement lime mortar as in wall or drain, etc complete all as specified and as directed |
| 5 | M&L for flush pointing to stone random rubble stone masonry, uncoursed or brought upto courses in cement mortar 1:3 as in drain, retaining wall etc. complete all as specified and as directed. |
| 6 | M&L for brick work with sub class `B’ bricks, straight or curved on plan to any radius in half brick thick walls, built in CM 1:4 complete all as specified and as directed |
| 7 | Demolition of cement concrete in ground floors and pavings n.exc 15cm thickness (below or above ground level) complete all as specified and as directed. |
| 8 | Demolition of reinforced cement concrete of any description and in any position not otherwise specifically provided for (reinforcement cut as required to facilitate demolition) complete all as specified and as directed |
| 9 | Formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200mm thick (Horizontal or sloping) complete all as specified and as directed |
| 10 | M&L for RCC Type A-I (1:1½:3 (using 12.5mm graded stone aggregate) for slabs supported on walls,beams and columns in floors,roofs, landings, balconies,canopies, deck slabs and in shelves and the like complete all as specified and as directed |
| 11 | M&L precast reinforced cement concrete (1:1½:3 type type-I using 20mm graded stone aggregate in cover slabs (for Manholes etc), shelves and similar articles with plain faces including necessary moulds and setting in cement mortar 1:6 including necessary form work complete all as specified and directed. (Note : Reinforcement to be measured & paid separately) |
| 12 | M&L Mild steel TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire annealed not less than 0.9mm dia or securing with clips all as specified and directed. |
| 13 | M&L 100 mm thick PCC (1:4:8 ) type D-2 as in sub base finished even and rough complete all as specified and as directed. |
| 14 | M&L for 25mm thick PCC 1:2:4 type B-0 (12.5mm graded stone aggregate) as in level course with finshining in cement concrete surface even and rough to receive screed bed complete |
| 15 | Dismantling floor, hearth, wall tiling including taking down plastering in cement mortor removing serviceable tiles to store and rubbish off the premises |
| 16 | Roughening surfaces of old concrete floor by picking, sweeping clean and washing down with water to remove dust etc. complete all as specified and as directed. |
| 17 | M&L for 16-18mm thick Granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, window-cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite over screed bed of 15 mm thick 1:6 complete all as specified and directed by Engineer in charge. |
| 18 | M&L for rounding to edges of stone slabs one edge, such as in steps, cooking platform, and other similar situations complete all as specified and directed by Engr-in-Charge. |
| 19 | M&L Joint free Non - skid coloured ceramic tiles 7 to 10 mm thick (square/rectangular) area of Each tile exceeding 0.18 Sqm but not exceeding 0.36 Sqm, in floors etc. set and jointed in neat cement slurry over screed bed of 15 mm thick 1:6 and pointed in white or coloured cement to match complete all as specified and as directed |
| 20 | M&L Joint free Non - skid coloured ceramic tiles 7 to 10 mm thick (square/rectangular) area of Each tile exceeding 0.18 Sqm but not exceeding 0.36 Sqm in skirting/dado or vertical surfaces with back coat of screed bed or bedding layer of 10 mm thick 1:4 and pointed in white or coloured cement to match complete all as specified. |
| 21 | M&L Joint free Non - skid coloured ceramic tiles 7 to 10 mm thick (square/rectangular) area of Each tile exceeding 0.11 Sqm but not exceeding 0.18 Sqm, in floors etc. set and jointed in neat cement slurry over screed bed of 15 mm thick 1:6 and pointed in white or coloured cement to match complete all as specified and as directed |
| 22 | M&L Glazed coloured ceramic tiles in verticle surfaces 450 x 300 x 7mm thick set and jointed in neat cement slurry and pointed in coloured cement to match with backcoat of screed bed or bedding layer 10mm thick 1:4 and pointed in white or coloured cement to match complete all as specified. |
| 23 | S&F selected quality looking mirror bevelled edge 5.5mm thick selected quality glass, mounted on 6mm thick commercial plywood, including moulding of all round edges of looking mirror and fixed to wooden plug with appropriate nos CP brass screwed cup washers complete all as specified and directed. |
| 24 | M&L 75 mm thick PCC (1:4:8 ) type D-2 as in sub base finished even and rough complete all as specified and as directed. |
| 25 | M&L Johnson Endura premium paving tiles of techno commercial or equivalent of size 40cm x 40cm x 10 mm thick, set, jointed and pointed in neat cement slurry in floors, laid over 15 mm thick bedding layer in Cement Mortar 1:6 complete all as specified and as directed. |
| 26 | M&L for cutting chases, pinning in, making good to facing where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades shelves, lintels etc, and cutting chases for concealed water tubing or concealed conduit wiring etc and making good, cutting not exc 10cm girth all as specified and as directed |
| 27 | Taking up or down GI Water Tubing 15mm dia (bore) including Connections and Fittings, segregating serviceable PipeS&Fittings and Stacking properly at Site(s) for re-use, complete all as specified and as directed. |
| 28 | All as per Ser Item No 27.00 above, but for 20mm dia (Bore). |
| 29 | M&L for 16 mm dia 3-layer PP-R Polypropylene random copolymer) concealed pipes SDR 7.4 (PN16) UV stabilized and antimicrobial fusion welded having thermal stability for hot & cold water supply including all PP-R plain & brass threaded polypropylene random fittings fixed complete to walls, ceilings or in floors etc. complete all as specified. |
| 30 | All as per Ser Item No 29.00 above, but for 20mm dia (Bore). |
| 31 | All as per Ser Item No 29.00 above, but for 32mm dia (Bore). |
| 32 | Taking up or down and refixing old PP-R pipe 20mm ida and connections in new or old position (Walls, ceiling, floors, etc.) complete all as specified and as directed |
| 33 | M&L Lagging to pipes used in internal water supply (internal dia of pipe 20mm) or plumbing all round with,25min thick bonded mineral wool preformed ‘SNAP ON’ pipe sections of density 144 Kg/Cum conforming to IS 9842 all as specified and directed by the Engr-in-Charge. |
| 34 | Dismantling water tanks of capacity exc 500 Ltr but not exc 1000 ltr capacity complete. |
| 35 | S&F rotational moulded polythene water storage tanks tripple layer (cylindrical vertical with closed top) hoisted and fixed in postion 1000 ltrs capacity with and including 25mm dia ball valves, high pressure of PTMT with epoxy coated aluminium rod and high density plastic ball screwed for iron pipe minimum weight 210 gram complete all as specified and directed. |
| 36 | S&F 25mm dia PP-R Gate valves (brass insert) as per requirement of the site complete all as specified and as directed |
| 37 | S&F in repair vitreous China squatting pan, Orissa pattern incl PVC trap, size 580 x 440 mm white, with integral foot rests squat pattern closet also includes setting the trap and pan in cement concrete (1 cement, 2 sand or surkhi and 5 aggretate), min. 150mm thick all round and finished just below level of rim of pan to receive the floor finishing (thickness as indicated) and making good floor complete all as specified incl cutting to the flush pipe and necessary repair to the floor complete all as specified and directed. |
| 38 | S&F in repair PVC Flushing Cistern 10 litre capacity, Low Level Valve Less, Symphonic Action type, White, with Inlet, Ball Valve, Float and Handle including 32mm dia PVC Flush Pipe, a Pair of MS Brackets,CP flush bend including Cutting and Pinning in Ends, Making Good Disturbed Surfaces in Cement Mortar 1:3 including taking down unserviceable Flushing Cistern and connected Items of any description, complete all as specified and as directed. |
| 39 | S&F vitreous china wash basin with pedestal, white, flat back, size 550mm x 400mm, including brackets, PVC waste pipe 32mm dia, waste coupling brass, chromium plated and including cutting for and pinning in ends of brackets or erecting stand, fixed in repairs complete all as specified and directed. |
| 40 | S&F brass Chromium plated Basin Mixer valve hot and cold screwed down for iron pipe complete, all as specified and directed. |
| 41 | S&F Brass CP Wall mixer for Mixing hot & cold water (3 in 1) screwed down for iron pipe and fixed bore of pipe 15mm complete all as specified |
| 42 | S&F in repair 15mm dia bib taps fancy type CP Brass with Capstanhead, screwed down, screwed for iron pipe of bore 15mm complete. |
| 43 | S&F in repair Angle Cock,15mm fancy type, chromium plated, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed complete all as specified and as directed. |
| 44 | S&F PVC Connections 15mm size with PTMT Nuts of length 600mm and fixed, complete all as specified and as directed. |
| 45 | S&F Brass CP Sink Mixer with regular spout for Mixing hot & cold water screwed down for iron pipe and fixed bore of pipe 15mm complete all as specified |
| 46 | S&F Brass chromium plated shower rose 125mm size with 225 mm Flange, swivel joints, including fixing to steel pipe or union complete all as specified and directed. |
| 47 | S&F Tubular towel Rail CP Brass, chromium plated D type with CP Brackets, 600 mm long between flanges all as specified. |
| 48 | S&F Glass shelf 450 x 125 x 6MM (with ABS Bracket chromium plated bracket guard and SS railing complete all as specified and as directed |
| 49 | S&F Soap Dish Stainless Steel complete all as specified & directed. |
| 50 | S&F Peg Set of 6 Stainless Steel as approved by Engr-in-Charge |
| 51 | S&F Corner Glass Shelf 300mm (with ABS Brackets) 300 x 300mm as approved by Engr-in-Charge |
| 52 | S&F Towel Ring including necessary stain less steel screws, rawl plugs and washers complete all as specified and directed. |
| 53 | S&F stainless steel plate rack of stain less steel 1.00 mm thick of size size 24 x 30 x 10 inch of best quality including necessary stain less steel screws, rawl plugs and washerscomplete all as specified and directed. |
| 54 | S&F sinks with drain board made of stainless steel lmm thick kitchen or laboratory with plugs, washers and wastes; including bedding in cement mortar on to dwarf wall or including fixing cantilever brackets and connecting union to pipe, overall size 495mm x 420mm bowl size 410mm x 330mm x 160mm complete all as specified and directed. |
| 55 | Demolition and taking out cement mortar or lime concrete, brick bats from sunken floor portion complete all as specified and as directed. |
| 56 | M&L for preparing surface of sunken slab and applying 15mm thick cement plaster 1:3 cement sand mortar with integral water proofing compound both on floor & wall. The surface shall then be cured and allowed to dry then applying Epoxy Resin coating PolymeRModified cementation coating like brush bond of Fosroc, Pidilite and Bostic as peRManufacturers instructions both on floor as well as on wall and sunken floor shall be filled with graded cinder concrete upto top level to receive top flooring, incl providing 25mm dia GI spout pipe projecting 0.25mtr beyond the external face of wall complete all as specified and directed by Engr-in-Charge. |
| 57 | M&L for 40mm thick PCC 1:2:4 type B-0 as in Sunken Portion of WC/Bath room (using 12.5mm graded stone aggregate) complete all as specifed and directed. |
| 58 | M&L for lime concrete with lime mortar 1:5:10 type E2 mix using 40mm graded brick coarse aggregate in sunken Portion of WC/bath room complete all as specified and as directed. |
| 59 | Dismantling of PVC / CI pipe 100mm dia jointed in cement mortar and taking out of trench if required complete all as specified. |
| 60 | Dismantling of PVC / CI pipe 75mm dia or less jointed in cement mortar and taking out of trench if required complete all as specified. |
| 61 | S&F 75 mm bore PVC (SWR) Soil, waste and vent pipes single socketed in any length with rubber ring joints fixed to walls and making good with cement mortor 1:3 complete all as directed. |
| 62 | S&F 75 mm bore PVC (SWR) Soil, waste and vent pipes single socketed in any length with rubber ring joints laid in trenches or in floorsand making good with cement mortor 1:3 or with PCC 1:2:4 complete all as directed. |
| 63 | S&F 110 mm bore PVC (SWR) Soil, waste and vent pipes single socketed in any length with rubber ring joints fixed to walls and making good with cement mortor 1:3 or with PCC 1:2:4 complete all as directed. |
| 64 | S&F 110 mm bore PVC (SWR) Soil, waste and vent pipes single socketed in any length with rubber ring joints laid in trenches or in floors and making good with cement mortor 1:3 or with PCC 1:2:4 complete all as directed. |
| 65 | S&F in repair PVC 110 mm bore Bend complete all as specified and as directed. |
| 66 | S&F in repair PVC (SWR) junction single, (Single T) equal or unequal with access door in 110 mm bore. |
| 67 | S&F in repair PVC 75 mm bore Bend complete all as specified and as directed. |
| 68 | S&F in repair PVC 75 mm bore Bend with access door complete all as specified and as directed. |
| 69 | S&F in repair PVC (SWR) junction single, (Single T) equal or unequal with access door in 75 mm bore. |
| 70 | S&F in repair PVC (SWR) vent cowl 110 mm bore complete all as specified and as directed. |
| 71 | S&F in repairs for PVC (SWR) floor/Nahani trap 75 mm dia outlet, plain with grating including jointing with solvent cement to waste pipe, fixed in cement concrete type B-1 (1:2:4) |
| 72 | Taking down chowkats or frames n.exc 1.50 Sqm Each with shutters (without taking off shutters from the frames) complete. |
| 73 | Taking down chowkats or frames exc 1.50 Sqm but n.exc 4.00Sqm Each with shutters (without taking off shutters from the frames) complete. |
| 74 | S&F Factory made single extruded WPC (Wood Polymer Composite) solid door/ window/Ceosetory windows & other Frames/Chowkhat of size 45 x 70 mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/Cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2, modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire retardant and fixed in position with MS hold fast/lugs/SS dash fasteners of required dia and length complete as per direction of Engineer-in-Charge. (M.S. hold fast/ lugs or SS dash fasteners shall be paid for separately).Note: For WPC solid door/window frames, minus 5mm tolerance in dimension i.e. depth and width of profile shall be acceptable. Variation in profile dimensions on plus side shall be acceptable but no extra payment on this account shall be made. |
| 75 | S&F Factory made single extruded WPC (Wood Polymer Composite) solid plain flush door shutter of 30mm size comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/Cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, all as per direction of Engineer-In-Charge.(Note : Includes all other connected accessories Net opening will be measured for payment purpose.) |
| 76 | S&F powder coated aluminium (minimum thickness of powder coating 50 micron) work for doors, windows, ventilators and partitions (Fixed portions) with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS:733 and IS:1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing/ paneling, C.P. brass/ stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-Charge. |
| 77 | Supply & fixing powder coated aluminium windows and ventilator shutters,sliding or fixed type without sash bars , aluminium section weighting 0.55 kg / m including necessary joining cleats , glazing clips ,roller, rubber packing, anodised aluminium snap beading , screws,anodised aluminium fitting such as peg stays hinges,handle,locking device, louvers, rollers etc. complete all as specified. (Note:- Glass pane and mesh will be measured and paid separately ) |
| 78 | S&F Sheet tinted glass 4.8mm thick tinted glass and glazing in squares complete all as specified and as direccted |
| 79 | S&F Stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples complete all as specified |
| 80 | Material & labour Three Track powder coated anodised aluminum frame and shutters for windows and ventilators with for anodised aluminium shutters for windows and ventilators with for anodised aluminium shutter two Nos fully glazed 5.5 mm thick tinted or plain glass with one No shutter having stainless steel mosquito proofing net 0.63 mm dia with 1.40 mm aperature with and including necessary rubber packing aluminium beading and necessary locking arrangement and powder coating of any colour (Thickness or powder coating not less than 50 micron) complete all as specified and directed.Sections of window shall be aluminium sections as follows:-(a) Three track frame bottom and top section 92 mm x 31.75 mm x 1.3 mm thick with weight 1.065 KG per RM.(b) Three track frame bottom and top section 92 mm x 31.75 mm x 1.3 mm thick with weight 0.929 KG per RM.(c) Shutter bottom and top 40 mm x 18 mm x 1.55 mm thick with weight 0.547 Kg per RM.(d) Shutter sides 40 mm x 18 mm x 1.55 mm thick with weight 0.547 Kg per RM.Note : (i) The rates shall be inclusive of supply & fixing of rubber packing / gasket, SS wire mesh & glass pane of suitable size and all necessary arrangemetn to fixing frame with brick wall / concrete surface.(ii) The rates shall be inclusive to make good the damage portion of brick wall / concrete surface with PCC 1:3:6 & CM (1:3) to match with existing surface. |
| 81 | M&L Bands, straps, supports or stays for rainwater, ventilating pipes, including bolts, if required: hooks (stay), heavy, for large gates; hook and pintle hinges: large hasps and staples; chains; hand made sliding bolts; clamps; hold fasts; wall ties; hooks for hanging fans; plain angle cleats for securing purlins to wood trusses or rafters; knee piece inserts; two way and three way straps, plate washers and similar small articles conforming to Fe-290 Gde-E-165 |
| 82 | M&L for PCC 1:3:6 type C-1(using 20mm graded stone agg) for bed block for fixing hold fast complete all as specified. |
| 83 | M&L for providing PCC 1:2:4 type B-0 as in roof kerbs or Mud stops rouded or chamfered on edges (using 12.5mm graded stone aggregate) complete all as specifed and directed. |
| 84 | M&L Pressed steel frames (Factory made) made out of 1.25 mm thick black MS sheet for doors, with one oRMore rebates including necessary s&f lugs, Butt hinges, lock strike plate, etc complete, size of frame 125x60mm incl bottom of Each chowkat to be welded with 2 nos 25x25x3mm thick flat iron projecting 10 cm on either side complete all as specified and directed. |
| 85 | M&L Pressed steel frames (Factory made) made out of 1.25 mm thick black MS sheet for doors, with one oRMore rebates including necessary s&f lugs, Butt hinges, lock strike plate, etc complete, size of frame 105 x 60mm incl bottom of Each chowkat to be welded with 2 nos 25x25x3mm thick flat iron projecting 10 cm on either side complete all as specified and directed. |
| 86 | S&F 35 mm thick, factory made 2nd class hardwood glazed and skeleton shutters, open rebated and prepare to receive gauge etc (without sash bars) edges of framing plain, chamfered or rounded fitted with cut and mitred beads for secruing glass/gauge etc size of member of shutter as specified in SSR Part-I Section 8 Clause 8.20(a), fitted to chowkats complete all as directed. |
| 87 | S&F 35mm thick flush shutters, solid core construction, with block board core and plywood face panesls, commercial type on bothe sides complete all as specified and as directed. |
| 88 | S&F 18mm thick Plywood, grade BWR, type BB, fixed with screws to timber frame work complete all as specified and as directed |
| 89 | M&L for 0.9mm thick decorative laminate type 1 of surface finish, colour and patters as approved, fixed with approved adhesive as per Manufacturer's insturctions, complete all as specified. |
| 90 | S&F Push to open Magnetic Catches for kitchen cabinet doors complete all as specified Make Hettich or equivalent as approved by Engr-in-charge |
| 91 | S&F Contneous (piano) hinges, mild steel, bright finish or electrogalvanised width of flaps (when open) 30mm complete all as specified and directed. |
| 92 | S&F Hasp and staple, safety type, brass with mild steel hinge pin including bolt to hinge plate and fixed with screws but of aluminium anodised complete all as specified and directed. |
| 93 | S&F Stainless Steel Decorative Cabinet Handle 100 mm complete all as specified and directed |
| 94 | S&F Stainless steel wire cloth, 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples all as specified and directed. |
| 95 | S&F Floor door stopper of aluminum alloy body and tongue anodized with hard drawn steel spring fixed in floor of length 150mm complete all as specified and directed by Engr-in-Charge. |
| 96 | S&F Stainless Steel butt hinges medium weight of size 100 mm fixed with stainless screws complete all as specified and directed Engr-in-Charge. |
| 97 | S&F Extruded aluminium alloy handles 150 mm long fabricated type anodised complete all as specified and directed . |
| 98 | S&F 200mm size aluminium anodised, barrel tower bolt of extruded section complete all as specified and directed by Engr-in-Charge. |
| 99 | S&F 150 mm long aluminium anodized barrel tower bolts of extruded section lcomplete all as specified and as directed. |
| 100 | S&F 250 mm long aluminium alloy anodised sliding door bolt with hasp and staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy complete all as specified directed. |
| 101 | S&F Decorative Stainless steel tubular curtain rail of 25mm dia incl six nos curtain ring per running mtr and one number of brackets on Each end and one no of globe on Each end of the rod per opening of door / window (make and materail approved by Engineer-in-charge) complete all as specified and directed. |
| 102 | S&F 2nd class hardwood small fittings such as brackets of any type, latch and hinge blocks, shaped door and widnow stops and the like, including all necessary labour; articles no exc 200 cu. cm Each complete all as specified and as directed |
| 103 | Dismantling of Wall and ceiling boards (fibre, pulp, insulation, etc.) any thickness, including cover fillets but without frame work. |
| 104 | M&L for PVC 5 to 6mm thick hollow PVC Ceiling as in flat surface including all fixing viz, U and L as design and pattern, including Gl frame work as flat surface approved as in ceiling comprising of Gl perimeter channel 0.55mm thick with two unequal flanges of 20mm and 30mm and web of 27mm fixed to surrounding wall using nylon sleeves and screws at 450mm center to center/intermediate channel 0.9mm thick having equal flanges of 15mm Each and web of 45mm suspended from soffit at approx 900mm center to center with Gl cleat and steel expansion fasteners with and including ceiling section (not exc 1.2m length) of 0.55mm thickness having kurled web of 50mm and flange of 26mm Each with lips of 10.50mm fixed to the intermediate channel at 457mm center to center fixed with hanger of Gl channel made out of GI channel used in ceiling as above upto 1200 mm length in roof slabs by means of ceiling cleats complete all as specified and directed by Engr-in-Charge. |
| 105 | Dismantling of Plain or corrugated steel sheeting, any gauge, thickness complete all as specified. |
| 106 | S&F Pre- painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws, height upto & inl triple sotrey bldg as specifiedare to be fixed using torque adjustable electronic gun screws drills of suitable capacity complete all as specified. |
| 107 | S&F Pre-painted galvalume aluminum zinc coating GI based Plain steel sheet 0.50mm thick as in ridges, eves board of red colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws in any height all as specified. |
| 108 | Dismantling boarding, any description, fixed in any position with nails complete all as specified. |
| 109 | Dismantling wrought iron oRMild steel work of any description not otherwise provided for complete all as specified and as directed |
| 110 | S&F rolled mild steel sections channel angle Tee section and in tubular section as in main and cross beams, hip and jack rafters; purlins,post where connected to common rafters and running rails fixed with angle cleat or other connecting plates conforming to Fe 410-W Gde-E-250, quality A complete all as specified and directed. |
| 111 | S&F framed work such as grills (incl window grill with 12 mm Square war), gratings, etc with ends of bars shouldered and / or riveted or forged into spikes; framed guard ; barred iron doors; ladders; framed balusters; walk ways; railing and simillar work Con-forming to Fe 290 Gde E-165. |
| 112 | Taking down cement plaster on brick or stone walls etc raking out joints hacking for key scrabbing down water etc complete. |
| 113 | M&L for 15mm thick cement plaster in CM (1:4) on fair faces of brick or concrete surfaces using WPC where ever required as per Manufacturerer's instructions and finishing the surface even and smooth (without using extra cement) etc. incl finishing even and fair complete all as specified NOTE -WPC shall be measured and paid separetely. |
| 114 | M&L for rendering 15mm thick on fair faces of brick work in CM 1:6 finished even and fair without using extra cement complete. |
| 115 | M&L for rendering 10mm thick in CM (1:3) on fair faces or concrete ceiling surfaces finished even and fair without using extra cement complete, all as specified and directed. |
| 116 | Supply only WPC complete all as specified and directed. |
| 117 | M&L for applying two coats of synthetic eneamel painting over a coat of pink primer on new wooden surfaces exc 10 cm width or girth including preparation of surfaces complete. |
| 118 | M&L Preparing new plastered or unplastered surfaces of walls and applying two coats of distemper oil emulsion, white or tinted over & including a coat of primer complete. |
| 119 | M&L for complete removal of existing surface and applying two coats of oil bound distemper over a coat of primer white or tinted on old decorated/undecorated surfaces of wall complete all as specified and directed. |
| 120 | M&L for 2mm thick wall care putty on wall complete all as specified and as directed |
| 121 | M&L preparing new plastered or unplastered surfaces of Ceiling and applying two coats of distemper oil emulsion paint complete all as specified and as directed |
| 122 | M&L for complete removal of existing surface and applying two coat of Oil Bound Distemper over a coat of primer on old decorated/undecorated surfaces of Ceiling complete all as specified and as directed. |
| 123 | M&L for 2mm thick wall care putty on ceiling complete all as specified and as directed |
| 124 | M&L for preparation of newly plastered surfaces of wall applying a layer of wall care putty 2mm thick (averaging) , Material & Labour for applying Two or More coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 Sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 Sqm over new surfaces complete all as specified and directed |
| 125 | M&L for complete removal of existing treatment by scrapping down of old surface of wall applying a layer of wall care putty 2mm thick (averaging) , Material & Labour for applying Two or More coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 Sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 Sqm over new surfaces complete all as specified and directed |
| 126 | M&L 75mm thick PCC 1:3:6 type C2 using 40 mm graded crushed stone aggregate as in plinth protection incl finishing even and smooth w/o using extra cement. |
| 127 | Taking down carefully any type of copper/aluminium point wiring (light,fan, socket or power) complete including conduits/casing caping with fittings such as switches,ceiling roses, pendents,regulators,bells, sockets, tube light fittings etc, removing the materials/debris and making good the disturbed surface of wall to match with the original existing finish all as specified and as directed. |
| 128 | Taking down existing ceiling and exhaust fans with all connected items and removing from site/ store and making good the disturbed surface on ceiling/fan hook and refixing on same positioncomplete all as specified and as directed. |
| 129 | Taking down unserviceable any type of Main Switch, DB's including MCBs incl wooden/GI/MS sheet board etc and removing from site and making good the disturbed surface of wall etc all as specified and as directed. |
| 130 | Taking down unserviceable any type of copper/aluminium sub main wiring of any size/core/type complete including conduits/casing caping etc, removing the materials/debris and making good the disturbed surfaces of walls, floors and ceilings etc to match with the original existing finish all as directed. |
| 131 | M&L for concealed point wiring with FRLS-H, PVC insulated, unsheathed multistranded copper conductor cables 1100 Volts grade of 1.5 Sqmm size (Phase and Neutral) alongwith one earth continuity conductor with FRLSH PVC insulated unsheathed multistranded copper conductor cable 1100 Volts grade of 1.5 Sqmm size through and including 20 mm dia (medium grade) rigid non metallic PVC concealed conduit terminated and suitable foRModulaRMetal flush box as per site requirement for fixing of switches, sockets, fan regulators etc including testing on completion complete including cutting chases for concealed conduit piping in making good to facing and pointing in using cement mortar 1:3 and making good to disturbed surface for the following. : Note: (a) Rate of modular cover plates are paid seperately in respected items. (b) Rate for any type of way connector to fix fittings are deemed in item cost. |
| 132 | All as per Ser Item No 131.00 above, but one 3 pin socket outlet 5 Amps on the same board with cable 1.5 Sqmm size. |
| 133 | All as per Ser Item No 131.00 above, but one 3 pin socket outlet 5 Amps on the Indepdent modular board with cable 1.5 Sqmm size. |
| 134 | All as per Ser Item No 131.00 above, but one light point controlled by 2- way switches with cable 1.5 Sqmm size. |
| 135 | M&L for point wiring with PVC insulated un-sheathed cable with stranded copper conductor FR-LSH conforming to IS : 694 of size 2.5 Sq mm single core, including one No. 2.5 Sq mm single core PVC insulated un-sheathed copper cable FR-LS as continuous earth wire drawn in and including PVC rigid/ conduit of suitable size (not less than 20 mm in width) ISI marked medium grade, white colour with all accessories of same grade,concealed on wall/ceiling including terminated in to Modular switch board / Cast iron/pressed steel terminal box 60mm deep of required size made out of 2mm thick MS sheet duly painted both sides with 3 mm thick plastic laminated sheet top cover fixed with brass screw & cup washers foRMounting switch socket combination 2 in 1, 3 pin, 5 and 15 Amp flush type / modular type on the independent board complete all as specified and as directed |
| 136 | Hanging only ceiling fan and connecting up including provision of cable from ceiling rose to fan complete all as specified and directed. |
| 137 | Fixing only exhaust fan and connecting up including provision of cable from ceiling rose to fan complete all as specified and directed. |
| 138 | S&F in repairs in repairs Ceiling rose surface bakelite 65 x 50 mm, three terminals, 240 volts all as specified. |
| 139 | S&F Modular switch 1 Way 06 Amps, 1 module complete all as specified and directed. Make-Anchor Roma/Crabtee/Schneider. |
| 140 | S&F Modular socket 6A 2/3 pin conbined 2 module complete all as specified and directed. Make-Anchor Roma/Crabtee/Schneider. |
| 141 | S&F Modular switch 1 Way 16 Amps, 1 module complete all as specified and directed. Make-Anchor Roma/Crabtee/Schneider. |
| 142 | S&F Modular socket 6A/16A 2/3 pin conbined 2 module complete all as specified and directed. Make-Anchor Roma/Crabtee/Schneider. |
| 143 | S&F Modular switch 2 Way 06 Amps, 1 module complete all as specified and directed. Make-Anchor Roma/Crabtee/Schneider. |
| 144 | S&F Modular fan regulator 2 module complete all as specified and directed. Make-Anchor Roma/Crabtee/Schneider. |
| 145 | S&F Modular Bell push 1 Way 06 Amps, 1 module complete all as specified and directed. Make-Anchor Roma/Crabtee/Schneider. |
| 146 | S&F Call Bell Ding dong type complete all as specified and directed. |
| 147 | S&F modular white cover plate with frame 2 module complete all as specified and directed. Make-Anchor Roma/Crabtee/Schneider. |
| 148 | S&F modular white cover plate with frame 3 module complete all as specified and directed. Make-Anchor Roma/Crabtee/Schneider. |
| 149 | S&F modular white cover plate with frame 4 module complete all as specified and directed. Make-Anchor Roma/Crabtee/Schneider. |
| 150 | S&F modular white cover plate with frame 8 module complete all as specified and directed. Make-Anchor Roma/Crabtee/Schneider. |
| 151 | S&F in repairs of tube light fitting 1x 20 watts 4 feet with LED batten with aluminium housing and integrated electronic driver in cluding LED tube light white colour complete including connecting up with twin core twisted flexible copper conductor cable with suitable size all as directed. Make: Havells Catpart No.ENDURALINEARNEOBS22WLED865SPCWH or equivalent Bajaj/ Crompton |
| 152 | S&F Lamp holder, PVC/Polycarbonate type with back plate suitable for batten fitting of LED lamp 9 watt complete all as specified and directed.Make: Anchor or equivalent |
| 153 | S&F LED lamp 9W LED lamp suitable for B-22 holder complete all as specified and directed Make: Bajaj Catpart No.9W CDL B22 or equivalent Havells/ Crompton |
| 154 | S&F DB with sheet metal enclosure 240 volts, 8 way with 200 Amp rated bus bar single pole & neutral double door type foRMCBs including mounting work as required in position .complete all as specified and as directed. Make-Havells/ABB/L&T/Schneider. |
| 155 | S&F MCB SPN 40 amps 230 volts C curve, 50 HZ AC 10 KA Make-Havells/ABB/L&T/Schneider. |
| 156 | S&F MCB SP 06 to 32 amps 230 volts C curve, 50 HZ AC 10 KA Make-Havells/ABB/L&T/Schneider. |
| 157 | M&L for Earthing complete with galvanised steel earth plate, electrode, 600x600x6.0 mm thick burried directly in ground (earth pit not less than 2.25m deep below normal ground level) connected to GI wire 4mm dia by mens of nuts, bolts, & washers of GI as shown in electrical plate No. 3 of SSR Part-I Connected to earthing ten point all as specified and including necessary earth pit PCC 1:3:6 chanber be 50mm thick PCC 1:2:4 chamber cover with 6mm dia mild steel reinforcement of 10 cm c/c spacing both ways in lieu of CI cover , watering arrangement shall be made with GI pipe medium grade of 20mm dia including funnel and protection to earth lead shall be provided with GI pipe light grade 15mm dia upto 7.5 from the earth plate electrode & refilling of soil etc including necessary excavation & earth work in any strata and PCC chamber all as specified and directed by Engr-in-Charge including demolish existing earth pit taking out old materials. |
| 158 | M&L for Sub Main wiring using FRLS Insulated unsheathed, multistranded copper conductor FRLS PVC cable 2 runs of size 2.5 Sqmm for phase and neutral and 2.5 Sq mm for earthing. drawn through rigid PVC conduit of suitable size fixed on wall/ground/Ceiling etc., and complete all as directed by Engr-in-Charge. Note: Phase should be Red / Yellow / Blue, neutral should be black and earthing wire should be green in colour. Two runs of cable for phase / neutral and one run of cable for earth incl conduit will be measured and paid as one unit length. |
| 159 | M&L for Sub Main wiring using FRLS Insulated unsheathed, multistrand copper conductor FRLS PVC cable 2 runs of size 6 Sqmm for phase and neutral and 6 Sq mm for earthing. drawn through rigid PVC conduit of suitable size fixed on wall/ground/Ceiling etc., and complete all as directed by Engr-in-Charge. Note: Phase should be Red / Yellow / Blue, neutral should be black and earthing wire should be green in colour. Two runs of cable for phase / neutral and one run of cable for earth incl conduit will be measured and paid as one unit length. |
| 160 | S&F of Energy efficient LED street Light Luminaire 60 watts capacity comprises a die-cast aluminium housing including connections with 2 run of 2.5 Sq mm aluminium unsheathed wire multistranded from LT over head line / junction box to the connector of fitting, complete all as specified. |
| 161 | S&F of Street light bracket made out of GI tubing 32 / 40 mm dia, light grade of approx length 1.2 mtr long bend to shape suitable for security light fittings with necessary MS clamps - 02 Nos with one coat of anti corrosive primer and two coats of aluminium paint including nut, bolt, washers etc all as specified. |
| 162 | S&F Opening the unserviceable/burnt fan 1200 mm sweep and cutting of old burnt copper winding and rewinding the same with super enamelled copper winding wire of suitable gauge including insulating material such as paper cotton sleeves, varnish, reassembling, testing and connecting for satisfactory run, complete all as specified and directed. |
| 163 | Supply and replacing of Ball bearing of the ceiling fan (any sweep) as per existing size incl greasing/oiling, complete all as specified and directed. Make:- SKF/ NBC or Equivalent |
| 164 | Supply and replacenment gun metal bushes of surface size for ceiling fan/Exchast fan incl necessary mechanical work, complete all as specified and directed. |
| 165 | Supply and Fix Capacitor of of 2.5 MFD for ceiling fan, complete all as specified and directed. |
| 166 | M&L for replacement ceiling fan blade set of three heavy duty suitable for 1200 mm sweep of suitable approved make as direcetd by Engr-in-Charge. |
| 167 | Supply and Fix PVC canopy for ceiling fan 1200 mm sweep complete for various makes/model of fan, complete all as specified and directed. |
| 168 | M&L for strip opening and cutting of old burnt copper winding of exhaust fan and rewinding of exhaust fan motor of sweep 350/450mm with super enamelled copper winding wire of suitable gauge including insulating material such as paper cotton sleeves, varnish, re-assembling, testing and connecting for satisfactory run, complete all as specified and directed. |
| 169 | Supply and Fix Capacitor of 4 Mfd for exhaust fan, complete all as specified and directed. |
| 170 | M&L for Ball bearing of exhaust fan of any size/make as per the existing, complete all as specified and directed. Make: SKF/NBC or equivalent make. |
| 171 | M&L for painting the exhaust fan including louvers of size 300/450mm sweep with two coats of synthetic enamel paint after cleaning and making the surface of oil/dust free, complete all as specified and directed. |
| 172 | Supply and laying in repair of XLPE insulated,sheathed,armoured,heavy duty LT 1100 volts grade cable 35 Sqmm 3.5 core with aluminium conductor laid in trenches/pipes, fixed to poles/walls with suitable saddle complete all as directed. |
| 173 | Excavation in trenches not exc 1.5 mtr wide and not exc 1.5 M in depth and getting out in soft/loose soil or hard /dense soil for taking up or laying of cable all as specified and directed. |
| 174 | Returning, filling in including spreading, levelling, watering and well ramming in layers not exceding Cum 25cm complete al as specified and directed. |
| 175 | Removal of surplus soil not exceed to a distance of 50M where directed at a level not exc 1.5M above the starting point. |
| 176 | Supply and laying dry river sand laid in trenches as cable cushioning and covering complete all as secified and directed. Note : Punned thickness shall be measured and paid. |
| 177 | M&L for brick well brunt locally available sub class'B' laid over sand cushioning to cable in trenches keping width of brick parallel to the length of cable complete all as specified and directed. |
| 178 | Taking out/taking down old unserviceable damaged GI/PPR pipe of following sizes from excavated trenches including removing of fittings all as directed for necessary replacement /relaying serviceable GI pipe all as directed by Engineer in Charge.size of 50 mm dia |
| 179 | All as per Ser Item No 178.00 above, but 32/40 mm dia. |
| 180 | All as per Ser Item No 178.00 above, but 25 mm dia. |
| 181 | Supply and Laying of PPR pipes 3- layer SDR 7.4 of outer diameter of pipes as following UV stabilized and antimicrobial fusion welded having thermal stability for hot and cold water supply all PPR plain & brass threaded polypropylene random fittings laid in trenches including fittings and testing complete all as specified and directed :- Size of 50 mm dia. |
| 182 | All as per Ser Item No 181.00 above, but, 32/40 mm dia. |
| 183 | All as per Ser Item No 181.00 above, but, 25 mm dia. |
| 184 | M&L for construction of Brick Masonry valve chamber of size 600x600x600mm (Internal dimensions) with PCC 1:4:8 foundation 150mm thick, brick work built in CM 1:6, PCC 1:3:6 coping 50mm thick, plastering 15mm thick in CM 1:6 to all internal and exposed surfaces including excavation earthwork in hard/dense soil, MS sheet cover 4mm thick and MS equal angle iron 50mmx50mmx6mm frame as per existing size with locking arrangement embedded in PCC suitable for 25/40/50mm gate valve and painting to MS cover with two coats of synthetic enamel paint over one coat of red oxide primer etc complete including dismantling old/damaged valve pits complete all as specified and directed. |
| 185 | S&F Making connection of PPR distribution branch with PPRMain of sizes 50 mm to 75 mm by providing and fixing tee including cutting and making fusion joint etc complete all as specified and directed. |
| 186 | Taking out unserviceable Gate valves from water pipe line for necessary replacement all as directed for valve size 15mm to 32mm |
| 187 | Taking out unserviceable Gate valves from water pipe line for necessary replacement all as directed for valve size 40mm to 80mm. |
| 188 | Supply and fixing PPR gate valve (brass insert) of size 32 mm dia including connection and testing complete all as directed. |
| 189 | Supply and fixing PPR gate valve (brass insert) of size 50 mm dia including connection and testing complete all as directed. |
| 190 | M&L Lagging on pipes of internal dia 15 mm, used in external water supply or plumbing all round with, 40mm thick bonded mineral wool preformed ‘SNAP ON’ pipe sections of density 144 Kg/Cum conforming to IS 9842, provided with chicken mesh wire netting 25 gauze 20mm mesh and finally covering with plaster of pairs including taking down old, complete all as specified and directed for the size of 50 mm bore tubing. |
| 191 | All as per Ser Item No 190.00 above, but, 32 mm bore tubing, complete all as directed. |
| 192 | All as per Ser Item No 190.00 above, but, 25 mm bore tubing, complete all as directed. Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Sep 25, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedOct 14, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 10 daysOct 16, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 12 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender