Tender For Periodical Services, Maintenance To Cupboard, Toilets Sanitary Fittings And Other Misc B/R Repair Works For Command Hut/Central Amenities, Offrs Md Accn At Or Near Arun Khetarpal Marg Road, Polo Road, Cassel Road, Parade Road, Mandir Marg
Tender Value
1.49 Crore
Estimated cost
Bid Submission
22 Oct 2026
21 days left
EMD
2.24 Lakhs
Bank guarantee accepted
Document Fee
1000
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
New Delhi → Delhi
EMD Exemption
Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for Periodical Services, Maintenance To Cupboard, Toilets Sanitary Fittings And Other Misc B/R Repair Works For Command Hut/Central Amenities, Offrs Md Accn At Or Near Arun Khetarpal Marg Road, Polo Road, Cassel Road, Parade Road, Mandir Marg Etc And Other Connected Areas In The Aor Of Age B/R-I Under Ge (East) Delhi Cantt-10
BOQ
| Sl. No. | Item Description |
| 1 | Taking down chowkats or frames with shutters (without taking off shutters from the frames) including iron mangory not exc. 1.5 Sqm each complete all as specified and directed. |
| 2 | Taking down chowkats or frames with shutters (without taking off shutters from the frames) including iron mangory exc. 1.5 sqm but n.exc 4 sqm each complete all as specified and directed. |
| 3 | Taking down shutters of any description not exceeding 2.00 Sqm each complete all specified and directed. |
| 4 | S&F solid PVC door frame of size 50mm x47mm made out of 5mm plain colour PVC sheet reinforced with MS square tube complete all as specified and directed. |
| 5 | S & F Factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, supplying & fixing in the frame at site as per specification & drawing. |
| 6 | S & F flush door shutter 35mm thick solid core construction with Block board and plywood face panels, commercial type on both sides. complete all as specified and as directed. |
| 7 | S & F 35 mm thick second class hard wood glazed and Skelton shutters open rebated and prepared to receive glass, gauge etc. (without sash bars) edges of framing plain, chamfered or rounded. fitted with cut and mitred beads for securing glass, etc. sizes of members of shutters as specified in SSR Part -I section 8 clause 8.24 (a) supplied and fitted to chowkhat |
| 8 | S & F framed work such as in door frame, door shutters / gate of angel , Flat iron or other section with MS sheet , cladding , gusset plates, rails, braces, , hold fast etc. complete , drilled for fixing of steel sheeting or other covering. Doors, etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings, including hinges hold fast of Fe 410-W (Gde E-250 quality) etc. complete all as specified and directed. |
| 9 | S & F Mild steel, plain, black sheet 1.60mm thick in wall cladding, steel gates and similar work, cut to size, holes punched; including round headed screws, clout nails or rivets and fixed to wood or steel framing with plain 40 mm lap joints with riveted or welded seams, including bending or turning up, mitred angles, etc. as required complete all as specified and as directed. |
| 10 | S & F for Factory made uPVC (white/Off white colour sliding window three track made out of extruded profiles with wall thickness of members as 2.3mm (1-0.2mm). Window profile with hollow section with multi chamber frame (60mm x 62mm) sash bars (42mm x 67mm). Sliding inter lock (one vertical length in each shutter 45.5mm x 28mm). Glazing head (24.5mm x 16mm) members will be mitred, cut and fusion welded in all corners including drilling of holes for fixing hardware and drainage of water. Making arrangement for fixing of hardware, EPDM gaskets 1.2, 1-0.2mm thick galvanised steel frame (30mm x 21.50mm). Sash bars (30mm x 18mm) profile to be inserted in required profile frame and will be fixed to the wall with 8mm x 100mm long fasteners. Hardware : Touch lock to be of Zinc alloy (white powder coated), Steel roller system including 5mm thick glazing with selected quality glass, Aluminium track on bottom rail to be of here track sliding frame, wool pine for sliding sash and interlock, complete all as specified and as directed. (Area exceeding 2.00 Sqm). (Note: The unit rate quoted by contractor includes cost of glass and includes all other connected accessories. Net opening will be measured for payment purpose.) |
| 11 | S & F for Factory made uPVC (white/Off White colour casement (Openable) Door made of extruded profile members with wall thickness of 2.3mm (1-0.2mm). Window profile members with hollow section with multi chamber. Frame (60mm x 58mm), sash bars (60min x 78mm). T-profile (One vertical length in between two shutters 60mmx 74mm). Glazing head (35mmx 20mm) will be mitred cut and fusion welded at all corners, including making of holes for fixing hardware and drainage of water etc., making arrangement for fixing of hardware EPDM gasket 1.2 to 0.02mm thick galvanised steel frame (28mmx21.50mm), sash bars (31mmx27mm). T-profile (27x17mm) to be inserted in required profile frame and will be fixed to wall 8mm x 100mm long fasteners. Hardware: casement door handle made of zinc alloy (white powder coated), Corner striker, Secondary Strikers, Cylinder, Door transmission gear made of mild steel with multi point locking system with striker, 3D Hinges of zinc alloy (white powder coated) and 5mm thick glazing with selected quality glass, complete all as specified and as directed.(Note: The unit rate quoted by contractor includes cost of glass and includes all other connected accessories. Net opening will be measured for payment purpose.) |
| 12 | S & F factory made uPVC white colour casement (Openable) Door made of extruded profile with wall thickness of 2.3mm ( + -0.2mm). Window profile with hollow section with muilty chamber, frame (60mm x 58mm), sash (60mm x 78mm). T profile (One vertical length in between two shutters) (60mm x 74mm). Glazing bead (35mm x 20mm) will be mitred cut and fusion welded at all corners, including drilling of holes for fixing hardware and drainage of water etc., making arrangement for fixing of hardware. EPDM gasket 1.2 + -0.2mm thick galvanized steel Frame (28mm x 21.5mm), sash (31mm x 27mm), T profile (27mm x 17mm) to be inserted in required profile, frame will be fixed to the wall with 8mm x 100mm long fasteners. Hardware: [casement door handle made of zinc alloyed (white powder coated). Corner striker. Secondary Strikers. Cylinder. Door transmission gear made of mild sleel with multi point locking system with strikes. 3D Hinges of zinc alloyed (white powder coated) and with stainless steel wire mesh (0.36mm nominal dia of wire and average width of aperture 1.40mm. (Note: The unit rate quoted by contractor include cost of wire mesh and all other connected accessories. Net opening will be measured for payment purpose.) |
| 13 | S&F Aluminium alloy powder coated windows sliding track (three track), bottom weighing not less than 1.015 Kg/RM, sides and top not less than 0.826 Kg/RM double riveted and 0.55Kg/RM for window shutter with one fixed glazed shutter and two nos glazed/gauged shutter sliding type with aluminium sections as per series - A (15mm) 3 track of Jindal section numbers for sliding windows with framed shutter including aluminium allow powder coated snap type beads handles with locking arrangement spring action and glazing clip joint cleats rubber gaskets etc. including provision of 4mm thick tinted glass/frosted glass of superior quality and stainless steel jali including all standard fittings, complete all as specified and as directed. |
| 14 | S & F Anodised aluminium window and ventilator shutters, powder coating of any colour, side hung type without sash bars, aluminium sections weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws, anodised aluminium fittings such as peg stays 150mm long (1 no.). hinges type B-21 100mm long (2 no.) suitable handle (1 no.) complete all as specified |
| 15 | S & F for Aluminium alloy powder coated door including frame and channel of section (Door frame single groove 101.6mm x 44.45mm x 1.80mm, shutter top section 47.62mm x 44.45mm x 1.80mm thick, shutter bottom section 114.30mm x 44.45mm x 1.80mm thick, shutter vertical section 85mm x 44.45mm x 1.80mm thick, shutter middle section 83.50mm x 44.45mm x 1.80mm thick & glazing clips weighing not less than 0.097 Kg/RM) including shutter fixed to sliding type/Openable frame and channel as directed and approved by GE and as per IS specifications including provn of 5mm thick tinted glass/12mm thick prelaminated particle board as required including handles, tower bolt, door closer heavy duty “SAMRAT”, locking arrangement “GODREJ”, rubber gasket and door stopper complete all as specified and as directed. |
| 16 | S & F for Powder coated aluminium partition with frame of standard powder coated aluminium sections of size 101.60mm x 44.45mm x 1.80mm in vertical and horizontal members and glazed with 5.5mm thick tinted glass and 12mm thick prelaminated particle board interior grade with laminations on both faces as directed by Engr-in-Charge according to site requirement including jointing cleats, glazing pins, rubber packing and fixing accessories as per site requirement including taking down existing partition of any type complete. |
| 17 | S & F for 10mm thick frosted toughened glass fixed as in doors, windows, shower partitions and similar work with all fittings reqd including cutting to shape, drilling holes including dismantling of existing glass of any type complete all as specified and directed |
| 18 | S & F in repairs ready made floor/wall mounted Vanity box made of HDHMR board, both side laminated consisting of the following combination :-(a) Wash Hand Basin 810mm x 500mm.(b) Base Cabinet 780mm x 485mm x 460mm.(c) Side Cabinet 300mm x 250mm x 1800mm.(d) Mirror cabinet size 780mm x 160mm x 800mm.Make : Hindware - Cat Part No. 70089 or 70084.Make : Kohler : Cat Part No. K-31602IN-E63 |
| 19 | S & F in repair aluminium dia cast door closer hydraulically regulated, designation No. 3, universal type, suitable for door shutters of 851 to 1000 mm in width and of weight between 61 to 80 kg and fixed. |
| 20 | S & F 100mm size stainless steel butt hinges fixing with screws to PVC door frame complete all as specified. |
| 21 | S & F Aluminium Anodised 150mm size barrel tower bolt complete all as specified and as directed. |
| 22 | S & F 150mm size aluminium anodised handles complete all as specified and as directed. |
| 23 | S & F 100mm size Mild steel butt hinges fixing with screws to Iron door frame complete all as specified. |
| 24 | S & F Mild steel 150mm size barrel tower bolt complete all as specified and as directed. |
| 25 | S&F Steel windows with side hung shutters including projecting type hinges with steel handle, and steel peg stay, complete with glazing bars, dovetailed or welded |
| 26 | S & F 300 mm long Mild steel sliding door bolts, plate type, stove enamelled black, with bright bolt not less than 12mm dia with and including a minimum of 6 bolts and nuts, four on bolt plate and two on staple plate and fixed complete all as specified and directed. |
| 27 | S & F of for mild steel pressed oval type handles stove enamelled black for doors 150 mm long complete all as specified and directed. |
| 28 | S & F of Floor door stopper of aluminium alloy body and tongue, anodized with hard drawn steel spring and vulcanised rubber piece fixed in floor, over all length of cover plate 140mm complete all as specified and directed. |
| 29 | S & F of 300mm long aluminium alloy anodised sliding door bolt with haps, staple ( bolt type ) and fixing clips of sheet, cast of extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy complete all as specified and directed. Please Enable Macros to View BoQ information |
| 30 | S & F of 300mm long aluminium alloy anodised sliding door bolt with haps, staple ( bolt type ) and fixing clips of sheet, cast of extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy complete all as specified and directed. Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Sep 24, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedOct 22, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 21 daysOct 23, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 22 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender