Tender For Renovation Work For Uphc(One Stop Centre) At Jayapuram Ward-25 In Tindivanam Municipality
Tender Value
18.90 Lakhs
Estimated cost
Bid Submission
09 Oct 2026
8 days left
EMD
18900
Bank guarantee accepted
Document Fee
Ref. Documents
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Villupuram → Tamil Nadu
EMD Exemption
Not Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for Renovation Work For Uphc(One Stop Centre) At Jayapuram Ward-25 In Tindivanam Municipality
BOQ
| Sl. No. | Item Description |
| 1 | Brick work in following Cement Mortar using best quality Burnt Clay Brick of size 9” x 4 3/8” x 2 3/4” with class designation of 7.5 conforming to IS 1077-1992 for foundation and basement including Cost of Mortar Plasticizer curing, etc.,complete complying with standard specification and as directed by the departmental officers. Brickwork shall be done as per IS 2212-1991 adopting English Bond generally.other type of bond shall be done as directed by the Executive Engineer in charge. |
| 2 | Dadooing walls with following best approved quality, white / colour glazed tiles conforming to IS 15622 of following sizes in Cement Mortar 1:2 (One Cement and Two crushed stone sand),10 thick with Mortar Plasticizer and pointing the joints with Water Resistant Tile Epoxy Grout at the rate of 0.27 Kg. / sq.m. neatly in all floors, curing, etc., complete complying with standard specification and as directed by the departmental officers.(The make and brand of the tiles should be got approved by Executive Engineer before use on works) |
| 3 | Fabricating Supplying and fixing in position of Aluminium anodised natural colour matt finish 1/3rd fixed glazing 2/3rd prelaminated board of Aluminium partition of size 2.700 mx 2.10 m.The outer frames Outer frame: 63.50x38x3mm@ 1.72 kg/m,Centre mullions: 63.50x38x3mm@ 1.55 kg/m,Alu. Clips: 17.27x17.15x1.50mm @ 0.175kg/mg/m for intermediate vertical mullion 90cm c/c. Horizontal mullion at 1.00m 2.10m covered with 4 mm thick plain glass with neccessary aluminium clips of size 17.27x17.15 x1.50mm @ 0.176kg/m and with required rubber beading etc., including necessary dismantling holes in RCC column,masonry wherever in necessary with power drills to the extent required and made good the damaged portion in good condition after fixing etc... complete complying with standard specification and as directed by the deparmental officers. All the aluminium sections should be anodised not less than 15 microns as ISI specification1868/1962 / and should be gotapproved by Executive Engineer before use. |
| 4 | Plastering with Cement Mortar 1:5 (One cement and Five Plastering sand), 12mm thick in all floors including mortar plasticizer at 200ml per 50Kg of cement used, curing etc. complete complying with standard specification and as directed by the departmental officers. |
| 5 | Painting Old Plastered Wall Surface with Two finishing coats of ready mixed (Emulsion) of approved quality and colour over the existing wall in all floors etc., complete complying with standard specification and as directed by the departmental officers. (The make, quality and colour of paint should be got approved by the Executive Engineer before use on works.) |
| 6 | Supplying and fixing Mild Steel grills for windows, ventilators etc.,complete complying with standard specifications and as directed by the departmental officers. |
| 7 | Painting new iron works such as steel doors, windows, ventilators, window bars, balustrades etc., with two coats of best approved first quality and colour of synthetic enamel paint over the existing red oxide priming coat in all floors excluding cost of priming coat etc., complete complying with standard specification and as directed by the departmental officers. (The make, quality and colour of paint should be got approved by the Executive Engineer before use on works.) |
| 8 | Paving the Top of roof with Solar refelective ceramic tiles of approved quality and colour laid in Cement mortar bed in 1:3 (One cement and three crushed stone sand) 12mm thick and pointed with water resistant tile epoxy grout for joint, curing etc., complete complying with standard specification and as directed by the departmental officers. (The make and brand of the tiles should be got approved by the Executive Engineer before use on works) |
| 9 | Wiring with 2 x 1.5 sqmm (22 /0.3 ) PVC insulated single core unsheathed copper conductor cable of 1100V grade in suitable PVC rigid pipe concealed in wall and ceiling with PVC accessories inflush with wall with 3mm thick hylum sheet cover with TW switch box and 5A F.T. switch with continuous earth wire connection of 14 SWG TC wire for making good of the concealed portion with suitable colour for PVC concealed light point / Fan point (For Electronic regulator). SD 23 |
| 10 | Wiring with 2 x 1.5 sqmm (22 /0.3 ) PVC insulated single core unsheathed copper conductor cable of 1100V grade in suitable PVC rigid pipe concealed in wall and ceiling with PVC accessories inflush with wall with 150 x 100 x 113 mm TW switch box with 3mm hylum sheet cover for 5A 3 pin non inter locking CS plug with continuous earth wire connection of 14 SWG TC wire and making good of the concealed portion with suitable colour for concealed PVC plug point. SD 38 |
| 11 | Supply and fixing of 1200mm (48\\") AC ceiling fan complete with stepped electronic 300W regulator with 1 meter down rod on the existing clamp SD-107 |
| 12 | Supply and fixing of single box type 4'36 W fluorescent fitting complete with electronic ballast with TW round blocks on wall or ceiling with flu tube with PVC unsheathed FRLS Copper leads from terminals to the fitting SD -87 |
| 13 | Drilling of 150 mm dia vertical bore well in hard rock area including drilling charges and including injection of casing pipe in the drilled hole etc complete (Page No:219) |
| 14 | Supply and delivery of 160 mm dia PVC causing pipe 6KSC/CM2 including cost of pipe ea complete |
| 15 | Labour Charges for inserting PVC casing pipes assembly (with slots or without slots) in the drilled hole including the jointing the pipes with PVC couplers with cement paste etc. complete |
| 16 | Supply and delivery of Wet type Submergible including all labour charges etc., complete., Submergible Motor 15 lpmx 80m.head 1 H.P (Page No:96) |
| 17 | Supply of 32mm UPVC Pipes specially made for deep borewell Submersible motor erection (ISI Make) including all cost materials, conveyance labours etc., complete as directed by departmental officers. |
| 18 | Cost and supply of 4Sqm cable 3 core including cost and conveyance of materials etc., complete (Page No:114) |
| 19 | Cost and supply of Nylon rope including cost and conveyance of materials etc., complete |
| 20 | Cost and supply of 32mm GI pipe inculding cost and conveyance of materials etc., complete (Page No:39) |
| 21 | Cost and supply of 32mm GI Coupling inculding cost and conveyance of materials etc., complete (Page No:42) |
| 22 | Cost and supply of 32mm GI Union inculding cost and conveyance of materials etc., complete (Page No:42) |
| 23 | Cost and supply of 32mm GI Gatevalve inculding cost and conveyance of materials etc., complete (Page No:43) |
| 24 | Cost and supply of 32mm GI Elbow inculding cost and conveyance of materials etc., complete |
| 25 | Cost and supply of 32mm GI Tee inculding cost and conveyance of materials etc., complete |
| 26 | Cost and supply of 32mm PVC Ball Valve. inculding cost and conveyance of materials etc., complete |
| 27 | Cost and supply of 20mm PVC screw down tap heavy type including cost and conveyance of materials cost. As per PWD schedule rates pg.no 48 |
| 28 | Cost and supply of 40mm Clamp Set including cost and conveyance of materials cost etc., complete (Page No:42) |
| 29 | Cost and supply of 160 mm pvc end cap including cost and conveyance of materials cost etc., complete |
| 30 | Cost and supply of Panel Board including cost and conveyance of materials cost etc., complete |
| 31 | Labour charges for Errection of submergible Pump set in bore well including fixing and jointing submergible cable with proper clamps up to the starter to required depth and also fixing of riser pipes to the required depth values Errection clamps pressure gauges up to the exterior wall of pump room and errction of panel board consisting of TPICN switches starter volmeter ammeter three pilot indicator lamps complete and testing the pump set and trail run for 10 days up to 5 HP. (Page No:226) |
| 32 | Supply and delivery and fixing of HDPE tank including loading and unloading. Transportation fixing and necessary GI Pipe and specials for pipe connection works including cutting. Threading and fixing charges as directed by departmental officers etc., complete (1000 Lit capacity 1 No) (Page No:83) |
| 33 | GST 18% Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Sep 24, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedOct 09, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 8 daysOct 09, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 8 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender