Tender For Repairs To Existing Toilet, Bathroom And Change Room Of Ladies Shift Room Bldg. No. 386A At Hef.
Tender Value
12.37 Lakhs
Estimated cost
Bid Submission
15 Oct 2026
14 days left
EMD
24760
Bank guarantee accepted
Document Fee
Ref. Documents
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Pune → Maharashtra
EMD Exemption
Not Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for Repairs To Existing Toilet, Bathroom And Change Room Of Ladies Shift Room Bldg. No. 386A At Hef.
BOQ
| Sl. No. | Item Description |
| 1 | Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing Serviceable tiles to store and rubbish off the premises |
| 2 | Demolition of unreinforced cement concrete in ground floors and pavings n exc 15 cm thickness (below or above ground level) |
| 3 | Demolition of Brickwork or stone/ boulder masonry, laid dry |
| 4 | Removing building materials etc. to a distance of 0.5km or under, beyond the lead included in the rates, including loading, unloading and stacking at the destination |
| 5 | Taking down & removing the shutters of any decription to the store/scrap yard but exc 1 sq. m and n exc 2 sq. m each. |
| 6 | Taking down Chowkhats or frames with shutters exc 1.5 sq. m but n exc 4 sq. m each for architraves, soffits, linings, window boards, etc. and removing to or from store of HEF |
| 7 | Dismantling structural steel work including doors, gates but excluding framed truss etc. |
| 8 | M&L for Excavation over area, n exc 1.5 m deep & getting out in soft and loose soil. |
| 9 | Rough Excavation, n exc 1.5 m deep & getting out in hard / dence soil. |
| 10 | M & L for Removing excavated material n exc. 50m and depositing where directed at a level n exc.1.5 m above the starting point in soft/loose soil |
| 11 | M & L for broken stone or boulder Loose filling with aggregates of gauge 80 to 150 mm in excavated area as per size and shape |
| 12 | M & L for Soling (or sub base) with broker boulders or quarried stone, inter stices filled, surface formed and rolled and consolidated to required gradient & camber with 200mm soling |
| 13 | M & L for Moorum/red bajri filling in floors or pavings, laid in layers n exc.15 cm thk, spread, levelled & rammed including watering. |
| 14 | M & L for cement concrete (nominal mix) type B2 1:2:4 (40mm graded aggregate) in Foundations, filling and mass concrete |
| 15 | M & L for 100 mm thk plain cement concrete type D2, 1:4:8 mix , using 40 mm graded aggregates, in sub-floors, floors, paving including shuttering etc. |
| 16 | TMT Mild steel bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips |
| 17 | M & L for providing 20mm thick Screed bed or bedding layer in cement mortar 1:6 mix for laying floor finishes |
| 18 | M & L for Non - skid coloured Ceramic tiles 7 to 8 mm thick area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match.(Size 600mm x 600mm) make- bell,somany, Johnson |
| 19 | M & L for Glazed ceramic tiles in vertical surface 450X 350X 7mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match, make- bell,somany, Johnson |
| 20 | Rendering 15 mm thick cement plaster on fair faces of brick work or concrete surfaces in CM (1:4). |
| 21 | M & L for old size brick with fly ash bricks straight or curved on plan exc 6 mean radius, built cement mortar in 1:4 |
| 22 | Rendering 15 mm thick even & smooth cement plaster on fair faces of brick work or concrete surfaces in cement mortar (1:4) mix without using extra cement even smooth and applying neeru finishing |
| 23 | S & F for 100 mm size CI nahani trap, with grating including jointing to waste pipe fixed in cement concrete type B 1 mix (1:2:4) |
| 24 | M & L for 100 mm size CI floor trap, with grating including jointing to waste pipe fixed in cement concrete type B 1 mix (1:2:4) |
| 25 | S & F Vitreous China wash down water closet pan (pedestal pattern), white (excluding fixing bolts, flushing cistern and flush pipe) |
| 26 | S & F for PVC (SWR) 'P' trap of 110mm Bore |
| 27 | S & F for PVC (SWR) 'S' trap of 110mm Bore |
| 28 | S & F for Vitreous China wash basin, angle back, size 600x480mm white, including taps, waste coupling of PTMT (half or full threaded), chain and plug and porcelain stopper & brackets. |
| 29 | Brass chromium plated 40mm bottle traps for wash basins with inlet and outlet screwed for pipe or connections including necessary packing, union and cap and fixed. |
| 30 | PVC (SWR) 75mm pipes single socketed, in any length with rubber ring joints, laid in trenches or in floors |
| 31 | PVC (SWR) 110mm pipes single socketed, in any length with rubber ring joints, laid in trenches or in floors. |
| 32 | S & F for vitreous China squatting pan, ‘Orissa’ pattern, size 580 x 440mm white, with integral foot rests complete including provision of lime concrete bedding (excluding flushing cistern & flush pipe) |
| 33 | S & F PVC 75 mm (SWR) junction single, (Single T) equal or unequal |
| 34 | S & F for PVC 75 mm (SWR) branch piece, single (single Y) equal or unequal |
| 35 | S & F for PVC 110 mm (SWR) branch piece, single (single Y) equal or unequal |
| 36 | S & F PVC (SWR) 110mm bends any radius |
| 37 | S & F PVC (SWR) 75mm bends any radius |
| 38 | Taking up or down 15 mm steel tubing and connections, including cleaning for refixing or removal to store |
| 39 | S & F Unplasticiscd PVC 15 mm pipes of pressure rating 10 kgf/cm2 laid in trenches |
| 40 | Supplying and laying of 15mm dia CPVC pipes SDR 11 & Plain CPVC SDR 11 fittings on walls /ceiling or laying in floors complete all as specified. |
| 41 | Brass CP mixer of 15mm dia for mixing hot & cold water screwed down for iron pipe and fixed |
| 42 | S & F of Stop valves 15mm dia, cast copper alloy, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed |
| 43 | S & F for Brass chromium plated shower rose 125mm size |
| 44 | S & F of 15 mm bore dia Bib taps fancy type, cast copper alloy with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule and fixed |
| 45 | S & F Flush pipe of polyethylene of low or high density or PVC. 32 mm dia, for low levelcistern |
| 46 | S & F for Flush pipes to pedestal pan, including all joints |
| 47 | M & L for health faucet (ABS body), mild steel chroumium plated suitable fo 15mm dia pipe with 1.25 metre long fexible tube and ABS wall hook including making connections and fixed in position complete in all respect as specified. |
| 48 | M & L for tubular round Brass chromium plated Towel Rail 20mm |
| 49 | M & L for Brackets of tubular round Brass chromium plated Towel Rail 20mm |
| 50 | S & F Soap dish, vitreous China white, approximate size 160x 160x90mm |
| 51 | Supply and fixing 30 mm thick Fiberglass Reinforced Plastic (F.R.P.) flush door shutter in different plain and wood finish made with fire retardant grade unsaturated polyester resin, moulded to 3 mm thick FRP laminate all around, with suitable wooden blocks inside at required places for fixing of fittings and polyurethane foam (PUF)/Polystyrene foam to be used as filler material throughout the hollow panel, casted monolithically with testing parameters of F.R.P. laminate conforming to table 3 of IS: 14856 complete all as specified by the manufacturer and as per directions of Engineer- in-charge. |
| 52 | Supply and fixing Fiber Glass Reinforced plastic (FRP) Door Frames of cross section 90 mm x 45 mm having single rebate of 32 mm x 15 mm to receive shutter of 30 mm thickness. The laminte shall be moulded with fire resistant grade unsaturated polyester resin and chopped mat. Door frame laminate shall be 2mm thick and shall be filled with suitable wooden block in all the three legs. The frame shall be covered with fiber glass from all sides. M.S. stay shall be provided at the bottom to steady the frame., complete as specified by the manufacturer and as per directions of Engineer-in-charge |
| 53 | S & F of Aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) with 150 mm in length and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed |
| 54 | S & F of Butt hinges of 100mm, extruded aluminium alloy with galvanised mild steel hinge pin, anodised and fixed, type B-21 |
| 55 | S & F of Extruded aluminium alloy handles of 100mm, fabricated type, anodised |
| 56 | S & F Flush shutters of 40mm thk, solid core construction, with block board core and plywood face panels, commercial type on both sides face is covered with decorative face veneer with lipping /frame to match |
| 57 | S & F of 1st class hardwood plain, solid, straight chowkats and frames, wrought, framed rebated on the solid, rounded or chamfered, put together with glue pinned at joints, supplied and fixed |
| 58 | S & F Powder coated Anodised aluminium window and ventilator shutters, fixed type without sash bar, aluminium section weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws etc. complete all as specified |
| 59 | S & F of 3mm thick sheet glass, ordinary quality and glazing with oil putty in square not exceeding 0.5 sqm in each pane. |
| 60 | S & F of Galvanised mild steel wire cloth, 0.56mm nominal dia of wire and average width of aperture 1.00mm and fixed with tinned tacks, or galvanised wire staples |
| 61 | S & F for Powder coated Anodised aluminium frame for doors, windows, ventilators with one or more rebates including joining cleat for fixing etc. complete all as specified |
| 62 | S & F of rolled mild steel in single stanchions, built up of one beam or channel section with flange plates, caps, bases, splices, angle brackets, cleats and other connections Fe-410-W(Gde-E-250) quality-A |
| 63 | S & F of Fe-410-W(Gde-E-250) quality-A roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats etc. |
| 64 | S & F of Pre- painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thk of an colour having tensile strength of 550 Mpa as in roof covering /cladding to wall, fixed with self tapping screws as specified |
| 65 | S & F of Mild steel screw bolts (machine made) with 16- 20 mm in dia. with hexagonal or square heads at one end and screwed the other, or screwed both ends, each screwed end to be fitted with washers and one hexagonal or square nut, but length of bolt exc 5 cm and n exc. 10 cm long |
| 66 | M & L for synthetic enamel painting in 2 coats on steel surfaces of any description including one coat of primer (red oxide) complete |
| 67 | S & F for 600mmx450mm bevelled edge mirror of selected quality glass, mounted on 6mm thick AC building board or commercial plywood and fixed to wooden plugs with chromium plated brass screws and cup washers |
| 68 | M & L for chalk whitening on plastered surfaces preparatory to distempering & apply two coats distemper oil emultion on wall. |
| 69 | M & L for preparing of surfaces on old surfaces & applying two coats of White washing on ceiling. |
| 70 | M & L for preparing of surfaces on old surfaces & applying two coats of cement paint on wall surfaces. |
| 71 | Taking down carefully copper/aluminium point wiring (light, fan, socket or power) complete, (fittings such as switches, ceiling roses, pendants, regulators sockets etc. to be measured separately), removing materials to store for keeping in safe custody for reuse at site and making good disturbed surfaces of walls, floors, etc. |
| 72 | Supply and fixing ceiling fans complete with blades, down rods, electronic regulator and accessories, 230 V, 1400mm with Min Air delivery 245 CFM and service value 6.0 BEE. Five starrated with brushless direct current motor (BLDC) |
| 73 | S & F of 240 V 40Amp. Double Pole Isolator/ MCB |
| 74 | S & F of Sheet metal enclosure for single pole & neutral 2 way without bus bar |
| 75 | S & F of Wiring for circuit/submain wiring alongwith earth wire with the following sizes of FR is PVC insulated copper conductor, single core cable in existing surface/ recessed steel as required 2x1.5 sq. mm + 1x1.0 sq. mm earth wire |
| 76 | S & F for One light point or one fan point controlled by one switch with cables 1.5 sq. mm size |
| 77 | M & L for Modular switch 1 way 6A, 1 module |
| 78 | S & F of White cover plate with frame, 4 module |
| 79 | S & F of Metal flush box 4 module |
| 80 | Supply and fixing LED street light fitting 35 Watt 230 V AC outdoor type with high pressure die cast aluminum hosing and heat resistant complete with driver, lamp bracket with impact and corrosion resistant including thermal management in multiple optics complete with IP 65/66 protection complete. |
| 81 | Supply and fixing LED lights fitting 1x 20W, 220V, AC decorative box type with driver, holder including LED tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete. |
| 82 | M & L Ceiling rose, 3 phase/PVC/ polycarbonate, isolated body |
| 83 | M & L Boxes junctions, plastic, round, four terminals |
| 84 | Supply and fixing of exhaust fan made of sturdy Engineering plastic complete with louvers shutter, voltage 230V, 50 Hz, RPM 1200, Copper winding of sweep 250mm |
| 85 | Cutting holes of exc 150 sq.cm but n exc 400 sq.cm into or through brick walls but in brick walls built in cement mortar or cement lime mortar and stone walls of lime concrete and making good in cement mortar 1:3 or cement concrete 1:2:4 type B-l as required Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Sep 24, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedOct 15, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 14 daysOct 16, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 15 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender