Tender For General Repairs With Replacement Of Defective Parts Of Snow Cat Tractor S.No. 9919 & Snow Cat Tractor S.No. 9920 Engaged For Snow Clearance Operation On Nathatop-Sanasar Road For The Season 2026-27
Tender Value
1.60 Lakhs
Estimated cost
Bid Submission
03 Oct 2026
4 days left
EMD
3210
Bank guarantee accepted
Document Fee
200
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Udhampur → Jammu and Kashmir
EMD Exemption
Not Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for General Repairs With Replacement Of Defective Parts Of Snow Cat Tractor S.No. 9919 & Snow Cat Tractor S.No. 9920 Engaged For Snow Clearance Operation On Nathatop-Sanasar Road For The Season 2026-27
BOQ
| Sl. No. | Item Description |
| 1 | Repair to cutting blade of the Snow Cat Tractor 9919 by way of checking, dismantling of blade and then P/F of High Tensile Bolts & Nuts. Supply of high tensile bolts (Grade 8.8/10.9, IS 1367), dia 20 mm, length 100 mm, with nuts & washers, zinc plated in place of old/ damaged/worn-out nut and bolts. Job includes cost of material, labour charge and taxes. |
| 2 | Complete oil change of Snow Cat Tractor 9919 by flushing old moil from the engine and washing engine tank with diesel and then Providing of i.e. engine oil-8 ltrs (15W40), Universal Tractor transmission Oil- 25 litre along with filter kit like M-Oil filter – 01 No., Diesel Filter-01 No., Hydraulic Filter – 01 No., Fuel water separator – 01 No. Job includes cost of material, labour charge and taxes. |
| 3 | Repairs to High Pressure Hydraulic Hose Assembly (4800 psi) of Snow Cat Tractor 9919 by P/F of one hydraulic hose assembly, length 10 ft(3.05 m), working pressure 4800 psi (330 bar),constructed from 4-spiral wire reinforced synthetic rubber hose, conforming to SAE 100R12 / EN 856 standards. Hose to be oil and abrasion resistant, with minimum burst pressure 4 × working pressure (≈19,200 psi). Hose ends shall be crimped steel fittings of appropriate size and thread type (BSP/JIC/ORFS), pressure tested at 1.5 × working pressure (≈7200 psi). Supplied complete and ready for installation Job includes cost of material, labour charge and taxes. |
| 4 | Repairs to electrical system of the Snow Cat Tractor 9919 by way of checking, dismantling, replacement and then P/F of new components ie. Headlights, work lamps, cabin lamps, wiper assemblies, wiper motors, switches, and wiring harnesses as required for safe tractor and snow plough operation. All electrical spares to conform to relevant IS standards (IS 1606 for lamps, IS 15885 for switches) and testing of replaced parts after reassembly. Job also includes repairs to self of the tractor by dismantling it, cleaning and testing of parts and the P/F of Self carbon brush set-01 set, Field coil -01 set, bendix drive-01 no., petrol for cleaning of parts, self-solenoid switch-01 no., voltage regulator-01 no. including rewinding of armature. Testing and fitting to the vehicle. Job includes cost of material, labour charge and taxes. Job includes cost of material, labour charge and taxes. |
| 5 | Repair to Radiator of the Snow Cat Tractor 9919 by way of dismounting of Radiator & then P/F of new parts in place of defective/worn-out parts i.e. Radiator brackets-02 no’s, hose pipe set-01 no. fan belt, Thermostat valve-01no., Coolant-03 ltr. Complete Job includes repairs to fins, tubes and then joining the cracked corners by binding solution to prevent leakage and fitting of the same to the vehicle after cleanings of radiator with caustic soda and testing the cost of material, labour charges and all other taxes. |
| 6 | Repairs to electrical system of the Snow Cat Tractor 9920 by way of checking, dismantling, replacement and then P/F of new components ie. Headlights, work lamps, cabin lamps, wiper assemblies, wiper motors, switches, and wiring harnesses as required for safe tractor and snow plough operation. All electrical spares to conform to relevant IS standards (IS 1606 for lamps, IS 15885 for switches) and testing of replaced parts after reassembly. Job also includes repairs to self of the tractor by dismantling it, cleaning and testing of parts and the P/F of Self carbon brush set-01 set, Field coil -01 set, bendix drive-01 no., petrol for cleaning of parts, self-solenoid switch-01 no., voltage regulator-01 no. including rewinding of armature. Testing and fitting to the vehicle. Job includes cost of material, labour charge and taxes. Job includes cost of material, labour charge and taxes. |
| 7 | Repair to Snow Plough Cutting Blades (MS Steel) of Snow Cat Tractor 9920 by way of dismantling of the blade by way of cutting of nut and bolts with the help of gas welding. The snow plough cutting blades shall be fabricated from mild steel plates conforming to IS 2062 Grade A, with hardness up to ~130 BHN. Each blade shall measure 6 ft 6”in length, 8” in width, and 1” in (25.4 mm) in thickness. -02 no blades. The plates shall be supplied in plain condition and subsequently drilled and fitted by the department to suit the mounting pattern of the tractor plough frame. The approximate weight per blade is calculated as: Volume = 1.98 m × 0.18 m × 0.025 m = 0.00891 m³ Weight = Volume × Density of Steel (7850 kg/m³) ≈ 70 kg per blade Dimensions for Bolt Holes, using 20 mm dia high tensile bolts (Grade 8.8/10.9, IS 1367). It is estimated that 8 holes per blade shall be drilled. The job also includes nominal hardening and facing of M.S sheet that is also arc welded and attached with the tractor assembly. |
| 8 | Complete oil change of Snow Cat Tractor 9920 by flushing old moil from the engine and washing engine tank with diesel and then Providing of i.e., engine oil-8 ltrs (15W40), Universal Tractor transmission Oil- 25 litre along with filter kit like M-Oil filter – 01 No., Diesel Filter-01 No., Hydraulic Filter – 01 No., Fuel water separator – 01 No. Job includes cost of material, labour charge and taxes. Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Sep 24, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedOct 03, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 4 daysOct 03, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 4 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender