Tender For Special Repairs To Bldg No T-90 & T-93 And T-178 At Nurla Mil Stn Under Age(I) Nimu.
Tender Value
44.50 Lakhs
Estimated cost
Bid Submission
15 Oct 2026
13 days left
EMD
89000
Bank guarantee accepted
Document Fee
500
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Leh → Ladakh
EMD Exemption
Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender For Special Repairs To Bldg No T-90 & T-93 And T-178 At Nurla Mil Stn Under Age(I) Nimu.
BOQ
| Sl. No. | Item Description |
| 1 | Dismantling timber scantling 40 sqcm and over in section, in any position in framed work in scantling etc complete all as specified and as directed by Engineer-in-Charge. |
| 2 | Material and labour second class Hard wood in clean sawn timber fixed and fixed in scantlings complete all as specified and as directed by Engineer-in-Charge. |
| 3 | Dismantling timber scantling as in fillets, rails, posts, rafters, purlins, etc. under 40 sqcm in section in any position as in framed work complete all as specified and as directed by Engineer-in-Charge. |
| 4 | Material and labour for 2nd class hard wood Plain fillets. exc. 13 & n.exc 25 Sq cm as in square, rectangular or triangular in section, clean sawn, secured with nails or brads complete all as specified and as directed by Engineer-in-Charge. |
| 5 | All as per item No 4 , but exc 3 & n.exc 6 Sq cm in bullnosed, splayed, chamfered or rounded on one edge or face as in beadding complete all as specified and as directed by Engineer-in-Charge. |
| 6 | Dismantling wall and ceiling boards (fibre,pulp, insulation, etc.) or insulation boards/slabs/ blankets, any thickness including cover fillets complete all as specified and as directed by Engineer-in-Charge. |
| 7 | Material and labour Prelaminated particle board 9mm thick, interior grade, prelaminated one side with decorative choice lamination and other side balancing white lamination, fixed with nails in ceiling, flat or sloping to timber frame work complete all as specified and as directed by Engineer-in-Charge. |
| 8 | Supply and fix 9mm thick Prelaminated particle board, interior grade, prelaminated one side with decorative choice lamination & other side balancing white lamination,fixed with nails to timber frame work as in walls complete all as specified and as directed by Engineer-in-Charge. |
| 9 | Supply and fix for Rolled sections as in main and cross beams, hip and jack rafters; purlins where connected to common rafters and running rails and guides for sliding doors;fixed with angle cleats or other connecting plates Fe-290 (Gde E-165) complete all as specified and as directed by Engineer-in-Charge. |
| 10 | Dismantling wrought iron or mild steel work of any description not otherwise provided complete all as specified and as directed by Engineer-in-Charge. |
| 11 | Demolition of Cement concrete (unreinforced) in ground floors and pavings n exc 15 cm thickness (below or above ground level) complete all as specified and as directed by Engineer-in-Charge. |
| 12 | Dismantling floor, hearth or wall tilling including cement mortar bedding ( but not backing ) removing serviceable tiles to store and rubbish of the premises complete all as specified and as directed by Engineer-in-Charge. |
| 13 | Material and labour 25 mm thick cement concrete type B- 1, 1:2:4 (20 mm graded aggregate) complete all as specified and as directed by Engineer-in-Charge. |
| 14 | Material and labour for Non - skid coloured Ceramic tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm, in floors etc. over 15mm thick Screed bed or bedding layer of mortar 15 mm thick for laying floor finishes in CM 1:6 set and jointed in neat cement slurry and pointed in white or coloured cement to match complete all as specified and as directed by Engineer-in-Charge. |
| 15 | Material and labour for Non - skid coloured Ceramic tiles 7 to 8 mm thick (square/rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors etc. over 15mm thick Screed bed or bedding layer of mortar 10 mm thick for laying floor finishes in CM 1:4 set and jointed in neat cement slurry and pointed in white or coloured cement to match complete all as specified and as directed by Engineer-in-Charge. |
| 16 | Demolition of Stone slabs and tiles of any description laid, bedded and pointed in in any mortar or thickness in floors, aprons etc. complete all as specified and as directed by Engineer-in-Charge. |
| 17 | Material and labour for 20mm thick Granite (of any type) tiles machine cut, bedded including Screed bed or bedding layer of mortar 15 mm thick in CM 1:4 for laying finishes and jointed with grey cement slurry and pointed with white cement with admixture of pigment to match the shade of granite stone including grinding and polishing complete all as specified and as directed by Engineer-in-Charge. |
| 18 | Taking down or up steel tubing and connections incl cleaning for refixing or removal to store for 15 mm dia bore complete all as specified and as directed by Engineer-in-Charge. |
| 19 | Supply and fix for 25mm outer dia 3-layer PP-R P o l y p r o p y l e n e random copolymer) concealed pipes SDR 7.4 (PN16) UV stabilized and antimicrobial fusion welded having thermal stability for hot & cold water supply including all PP-R plain & brass threaded p o l y p r o p y l e n e random fittings fixed complete to walls, ceilings or in floors etc complete all as specified and as directed by Engineer-in-Charge. |
| 20 | Dismantling broken water tank of cap exc 500 ltr but n exc 1000 ltr complete all as specified and as directed by Engineer-in-Charge. |
| 21 | Supply and fix for 1000 ltr cap Rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top) hoisted and fixed in position all as specified in SSR Part I complete all as specified and as directed by Engineer-in-Charge. |
| 22 | Supply and fix in repair vitreous china wash basin white flat back size 550x400mm ovel type/round /any shape (including tap, waste chain and plug and porcelain stopper and brackets all complete all as specified and as directed by Engineer-in-Charge. |
| 23 | Supply and fix in repair 15mm fancy type Bib taps, Chromium plated cast copper alloy with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule and fixed complete all as specified and as directed by Engineer-in-Charge. |
| 24 | Supply and fix in repair 15mm dia Angle cock/Stop valves, cast copper alloy,screwed down, high pressure,with crutch or butterfly handle,screwed both ends for iron pipe or for unions and fixed complete all as specified and as directed by Engineer-in-Charge. |
| 25 | Supply and fix in repair for 15mm PVC connections of 600mm long with PTMT nuts complete all as specified and as directed by Engineer-in-Charge. |
| 26 | Supply and fix in repair 15mm dia Fancy type Pillar taps, cast copper alloy, with capstan heads,chromium plated,screwed down high pressure, with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly-nuts, screwed for iron pipe and fixed complete all as specified and as directed by Engineer-in-Charge. |
| 27 | Supply and fix in repair 15mm brass Chromium plated for mixing hot & cold water screwed down for iron pipe and fixed complete all as specified and as directed by Engineer-in-Charge. |
| 28 | Supply and fix in repair 600mmx450mm bevelled edge mirror of selected quality glass, mounted on 6mm thick AC building board or commercial plywood and fixed to wooden plugs with chromium plated brass screws and cup washers complete all as specified and as directed by Engineer-in-Charge. |
| 29 | Supply and fix in repair Ball brass valves,high pressure, with polythene float and flynut complete, screwed for ironpipe or brass ferrule and fixed complete all as specified and as directed by Engineer-in-Charge. |
| 30 | Supply and fix in repair Brass chromium plated Tubular towel rail, 20mm dia, D type, 60cm long between flanges complete all as specified and as directed by Engineer-in-Charge. |
| 31 | Supply and fix in repiar Soap dish, vitreous China white, approximate size 160x 160x90mm complete all as specified and as directed by Engineer-in-Charge. |
| 32 | Supply and fix in repair Sheet glass shelf assembly consisting of 5.5mm thick sheet glass shelf 12cm wide with chromium plated bracket guard andrailing 60cm long complete all as specified and as directed by Engineer-in-Charge. |
| 33 | Supply and fix in repair 15mm Stop valves, cast copper alloy, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed complete all as specified and as directed by Engineer-in-Charge. |
| 34 | Supply and fix in repair PVC valveless, syphonic action type, flushing cistern 10 lts capacity, low level, white, with inlet, ball valve, float and handle including brackets complete all as specified and as directed by Engineer-in-Charge. |
| 35 | Supply and fix in repair Vitreous china wash down water closet pan \\"Pedestal Pattern\\" white, with seat white closed pattern with flat bottom and cover mild steel chromium plated or aluminized hinging deviced including flush pipe and joint etc and connection to drain, flushing, pipe, anti-syphonage pipe, and fixing arrangements with fixing bolts etc including making good the disturbed portion of floor in cement concrete 1:2:4 type B-0, complete all as specified and as directed by Engineer-in-Charge. |
| 36 | Dismantling Plain or corrugated steel sheeting,any gauge, thickness, including Nainital or similar pattern roof coverings complete all as specified and as directed by Engineer-in-Charge. |
| 37 | Supply and fix Pre- painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering /cladding to wall, fixed with self tapping screws complete all as specified and as directed by Engineer-in-Charge. |
| 38 | Pre-painted galvalume aluminum zinc coating GI based Plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and as directed by Engineer-in-Charge. |
| 39 | Supply and fix in repair sinks made of stainless steel 1.0mm thick kitchen or laboratory with plugs, washers and wastes; including bedding in cement mortar on to dwarf wall or including fixing cantilever brackets and connecting union to pipe, overall size 495mm x 420mm bowl size 410mm x 330mm x 160mm complete all as specified and as directed by Engineer-in-Charge. |
| 40 | Demolition of precast concrete block walling masonry, built in cement mortar complete all as specified and as directed by Engineer-in-Charge. |
| 41 | Material and labour for Pre-cast cement concrete block masonry in cement concrete 1:3:6 type C1(using 20mm graded aggregate) with solid blocks, exc. 10 cm in width and setting in mortar 1:4 complete all as specified and as directed by Engineer-in-Charge. |
| 42 | Material and labour for Rendering 15mm thick on fair faces of concrete block masonry surfaces in cement mortar (1:4) complete all as specified and as directed by Engineer-in-Charge. |
| 43 | Material and labour for Rendering 10mm thick on fair faces of concrete block masonry surfaces in cement mortar (1:6) complete all as specified and as directed by Engineer-in-Charge. |
| 44 | Material and labour preparing new plastered surfaces of walls and applying one of cement base paint over a coat of primer complete all as specified and as directed by Engineer-in-Charge. |
| 45 | Material and labour preparing new plastered surfaces of walls and Chalk whiting, on plastered surfaces, prepara-tory to distempering applying one coat of Distemper oil emulsion white or tinted complete all as specified and as directed by Engineer-in-Charge. |
| 46 | Material and labour for light shade Virified Ceramic tiles 10 mm thick (square/ rectangular) polished, area of each tiles not exceeding 0.36 sqm, in floors etc. incl 15mm thick screed bed in CM 1:4, set and jointed in neat cement slurry and pointed in white or coloured cement to match complete all as specified and as directed by Engineer-in-Charge. |
| 47 | Material and labour glazed ceramic tile \\" coloured\\" 450mmx 300mm x 7mm as in verticle surface such as skirting /dado etc, set and jointed in neat cement slurry and pointed with white cement mixed with pigment to match the shade of tile, fixed over and incl 10mm thick bedding layer in cement mortar 1:4 on concrete block wall surface complete all as specified and as directed by Engineer-in-Charge. |
| 48 | Formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200mm thick (Horizontal or sloping) complete all as specified and as directed by Engineer-in-Charge. |
| 49 | TMT bars 10 mm dia and above, cut to length , bent to shape required including cranking , bending spirally for hooping for columns, hooking ends, binding with and including mild steel wire ( annealed ) not less than 0.9mm dia complete all as specified and as directed by Engineer-in-Charge. |
| 50 | Material and labourfor RCC1:2:4 ( Nominal Mix) (20mm graded crushed stone agg) as in Slabs supported on walls, beams and columns in floors,roofs, landings, balconies, shelves and the like complete all as specified and as directed by Engineer-in-Charge. |
| 51 | Rolled mild steel sections as in framing for cladding, glazing and the like fixed with angle cleats and connecting plates, etc. Fe 410 -W (Gde-E- 250) quality-A complete all as specified and as directed by Engineer-in-Charge. |
| 52 | Supply and fix for Framed work such as grills, gratings, etc.. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe.290.Gde-E-165 complete all as specified and as directed by Engineer-in-Charge. |
| 53 | Material and labour painting on steel surface over 10 cm width or girth including preparation of surface and applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and as directed by Engineer-in-Charge. |
| 54 | Supply and fix for 0.63mm Galvanised, corrugated mild steel sheeting with two corrugations side lap, fixed with L-type or J-type hook and washers, in roofs, walls etc. with grade of zinc coating 275 complete all as specified and as directed by Engineer-in-Charge. |
| 55 | Material and labour for preparation of old painted steel surfaces of any description, over 10cm in width or girth,not otherwise described and applying two coats of Synthetic enamel (ordinary tint) complete all as specified and as directed by Engineer-in-Charge. |
| 56 | Taking down chowkhats or frames exc 1.5 sq. m but n exc 4 sq.m each (without taking off shutters from the frame) complete all as specified and as directed by Engineer-in-Charge. |
| 57 | Taking down Shutters of any description exc 1 sqm each but n exc 2 sqm each complete all as specified and as directed by Engineer-in-Charge. |
| 58 | Supply and fix Powder coated aluminium (minimum thickness of powder coating 50 micron) frame for doors, windows, ventilators with one or more rebates including joining cleat for fixing etc complete all as specified and as directed by Engineer-in-Charge. |
| 59 | Supply and fix Powder coated (minimum thickness of powder coating 50 micron) anodised aluminium door shutters, aluminium section weighing 0.55 Kg/m including necessary joining cleats, glazing clips, rubber neoprene packing, anodised aluminium snap beading screws etc. complete all as specified and as directed by Engineer-in-Charge. |
| 60 | Material and labour for plain sheet glass 4.80mm thick ordinalry quality and glazing with oil putty or wooden beads in square or fixed with aluminium section including rubber beads not exc 0.50 sqm in each pane complete all as specified and as directed by Engineer-in-Charge. |
| 61 | Supply and fix in repair Door closer hydraulically regulated designation No 3 universal type, aluminium body suitable for door shutters of up to 700 mm in width and weight not more than 35 Kg and fixed complete all as specified and as directed by Engineer-in-Charge. |
| 62 | Supply and fix solid PVC Door Frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S. Square tube, suppling & fixing in opening complete all as specified and as directed by Engineer-in-Charge. |
| 63 | Factory made solid panel PVC door shutter30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heatmoulded plain colour PVC ‘C’ channelhaving a PVC sheet strip of 20mm width stuck inside with solvent cement for stilesand plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, suppling & fixing in the frame at site complete all as specified and as directed by Engineer-in-Charge. |
| 64 | Supply and fixing Gypsum Board 12mm thick for ceiling/walling fixed with screw as per manufacturers instructions , along with Anodised aluminium snap grid frame work for false ceiling all as specified including Hangers 6 mm dia. G.I. (upto 1200mm length) adjusting level fixed to roof slabs by means ofceilling cleats made out of G.I. flat 40 x 3 mm size 60mm longand expansion hold fasteners 12.5mm dia. 40mm long complete all as specified and as directed by Engineer-in-Charge. |
| 65 | Material and labour for 10mm thick teak wood finish laminated wooden flooring interlocked with each others and its size as directed,over 6 micron polyethylene sheeting over the concrete to minimize moisture migration from the concrete complete all as specified and as directed by Engineer-in-Charge. |
| 66 | Material and labour for fix in repair 18/19mm thick Particle board, medium density, flat pressed,single layer type or three layer type with BWR type adhesive, fixed with nails to timber frame work complete all as specified and as directed by Engineer-in-Charge. |
| 67 | Material and labour for 0.9mm thick ,Decorative laminate type 1 of surface finish, colour and pattern as approved, fixed with approved adhesive complete all as specified and as directed by Engineer-in-Charge. |
| 68 | Supply and fix 75mm Butt hinges, cast brass, with mild steel hinge pin, bright polished and fixed, type B-12 complete all as specified and as directed by Engineer-in-Charge. |
| 69 | Material and labour for 75mm thick Cement concrete type C- 2,1:3:6 (40mm graded aggregate) as in plinthe protection complete all as specified and as directed by Engineer-in-Charge. |
| 70 | Supply and fix PVC (SWR) pipes single socketed, in any length with rubber ring joints, laid in trenches or floor of 75mm bore pipe complete all as specified and as directed by Engineer-in-Charge. |
| 71 | Supply and fix PVC (SWR) floor trap of 75mm plain with grating including jointing with solvent cement complete all as specified and as directed by Engineer-in-Charge. |
| 72 | Supply and fix BALL VALVE 25mm dia complete all as specified and as directed by Engineer-in-Charge. |
| 73 | Supply and fix 25mm Nipple suitable for HDPE water tank (Minimum weight 20mm-45 gms complete all as specified and as directed by Engineer-in-Charge. |
| 74 | Demolition and breaking up drain pipes (Salt glazed ware, AC or Reinforced concrete) set in cement mortar of internal dia 75-100mm incl any earth work and demolition of PCC complete all as specified and as directed by Engineer-in-Charge. |
| 75 | Material and labour for 100mm thick cement concrete 1:3:6 type C2 bed to drain pipes including packing under, and haunching against the sides of pipes after they are laid and tested complete all as specified and as directed by Engineer-in-Charge. |
| 76 | Supply and fix PVC (SWR) pipes single socketed, in any length with rubber ring joints, laid in trenches or floor of 110mm bore pipe complete all as specified and as directed by Engineer-in-Charge. |
| 77 | Excavating in trenches ,n exc 1.5 m wide and n exc 1.5 m in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. n exc 10 sq m on plan and n exc 1.5 m in depth and getting out in hard /Dense Soil complete all as specified and as directed by Engineer-in-Charge. |
| 78 | Returning, filling in, including spreading, levelling, watering and well ramming in layers not exc 25 cm. in hard / dense soil complete all as specified and as directed by Engineer-in-Charge. |
| 79 | Removing excavated material n exc. 50m and depositing where directed at a level n exc. 1.5 m above the starting point complete all as specified and as directed by Engineer-in-Charge. |
| 80 | Demolition of stone/boulders masonry, laid dry complete all as specified and as directed by Engineer-in-Charge. |
| 81 | Demolition of stone/ boulder masonry, built in cement mortar including all quoins, arches, pillars, etc, but excluding ashlar facings, dressed stonework and precast concrete articles complete all as specified and as directed by Engineer-in-Charge. |
| 82 | Material and labour for stone masonry Walling of random rubble, uncoursed, well bonded, bedded and solidly hearted, built in cement mortar 1:4, complete all as specified and as directed by Engineer-in-Charge. |
| 83 | Material and labour for stone masonry Walling of random rubble, uncoursed, well bonded, and solidly heartd laid dry complete all as specified and as directed by Engineer-in-Charge. |
| 84 | Demolition of Reinforced Cement Concrete in ground floors and pavings n exc 15 cm thickness (below or above ground level) (reinforcement cut as required to facilitate demolition) complete all as specified and as directed by Engineer-in-Charge. |
| 85 | Material and labour for cement concrete 1:4:8 type D2 (using 40mm graded crushed stone aggregate ) in foundation, filling and mass concrete complete all as specified and as directed by Engineer-in-Charge. |
| 86 | Material and labour for Precast reinforced cement concrete, type B-1, 1:2:4 (Using 20mm graded crushed stone aggregate) as in manhole cover set in cement mortar 1:4, complete all as specified and as directed by Engineer-in-Charge. |
| 87 | Supply and fix for 110 mm bore PVC (SWR) bends any radius complete all as specified and as directed by Engineer-in-Charge. |
| 88 | Supply and fix PVC (SWR) Vent cowl of 110mm bore complete all as specified and as directed by Engineer-in-Charge. |
| 89 | Taking down carefully aluminium/Copper point wiring light, fan socket or power complete fitting such as switches, ceiling rose, fan regulator, socket including light fitting etc complete with /PVC /MS conduit and T/W battern / casing caping complete all as specified and as directed by Engineer-in-Charge. |
| 90 | Taking out old unsv underground cable of any size/make/ type etc from excavted tranches/ on pole passing through pipes etc from different locations complete all as specified and as directed by Engineer-in-Charge. |
| 91 | Supply and laying or fixing or passing through pipe, 1100 volts grade heavy duty cable with PVC insulated aluminium conductor served with an inner sheathing of PVC tape armoured with galvanised steel wire or tape and overall PVC sheathed 2 core 16 sq. mm nominal cross section complete all as specified and as directed by Engineer-in-Charge. |
| 92 | Material and labour in repair for point wiring with PVC FRLS insulated single core cable of stranded copper conductors of size 1.5 sqmm, 1100 volt grade drawn in and including rigid PVC casing caping accessories lain on wall/ceiling surface and fixed with PVC saddles and back-plate and GI screws, including PVC insulated single core cable of stranded copper conductor of size 1.5 sqmm as earth continuous wire connected to common earth and PVC Board for housing like switches, sockets, fan regulators etc all as directed by Engineer-in-Charge for One light point/one fan point controlled by one switch complete all as specified and as directed by Engineer-in-Charge. |
| 93 | One 3 pin 5 amps socket outlet independent with cables 2.5 sqmm size complete all as specified and as directed by Engineer-in-Charge. |
| 94 | One 3 pin 5 Amp socket outlet on same board complete all as specified and as directed by Engineer-in-Charge. |
| 95 | All same as per item No 92 above but with conductor of size 4 sqmm (Nominal area) for one 3 pin socket outlet 15 Amps on independent board complete and earth continuity wire with 4 sqmm PVC insulated stranded copper conductor Cable complete all as specified and as directed by Engineer-in-Charge. |
| 96 | One bell/ buzzer point controlled by one push button on the same board with other switches or independent with cables1.5 sqmm size complete all as specified and as directed by Engineer-in-Charge. |
| 97 | Material and labour Buzzer, Ding Dong AC 230 volts, single pole complete all as specified and as directed by Engineer-in-Charge. |
| 98 | Supply and fix Bell push, flush type, 5 amp Switch , single pole, one way complete all as specified and as directed by Engineer-in-Charge. |
| 99 | Supply and fix Socket 2 in 1, 5 pin 5 Amp flush type complete all as specified and as directed by Engineer-in-Charge. |
| 100 | Supply and fix Switch piano flush type 5 Amp, single pole, one way complete all as specified and as directed by Engineer-in-Charge. |
| 101 | Supply and fix Switch socket combination 2 in 1, 3 pin, 5 Amp flush type complete all as specified and as directed by Engineer-in-Charge. |
| 102 | Supply and fix Switch Socket Combination 2 in 1, 3 pin, 15/16 amp flush type Universal complete all as specified and as directed by Engineer-in-Charge. |
| 103 | Material and labour for ceiling rose surface Bakelite 65x50mm two to three terminal complete all as specified and as directed by Engineer-in-Charge. |
| 104 | Supply and fix LED light fitting 1x9W/1X10W bulkhead luminaires including LED light driver holder connecting up with three core flexible copper conductor cable of suitable size complete all as specified and as directed by Engineer-in-Charge. |
| 105 | Supply and fixing LED light fitting with high out put diffuser 2 feet, 10 watt 220 V AC decorative type with driver holder and LED lamp including connecting up with three core flexible copper conductor cable of suitable size complete all as specified and as directed by Engineer-in-Charge. |
| 106 | Supply and fix basic all purpose surface and wall mounted LED batten with polycarbonate housing and integreted electronic driver of cap 20 watt, 4 feet long, with all accessories complete all as specified and as directed by Engineer-in-Charge. |
| 107 | Supply and fix Decorative wall mounting with matt gold finish with soda glass suitable for 4 W G9 LED Lamp with G9 base basic all purpose light with polycarbonate housing and integreted electronic driver of , with all accessories complete all as specified and as directed by Engineer-in-Charge. |
| 108 | Supply and fix in repair sheet metal powder coated versatile Double door SPN distribution board, 12 way suitable for MCB's fitted with copper bus bar rated 200amps, neutral link , earth bar and din rail suitable for use on 240 Volt, 50Hz complete all as specified and as directed by Engineer-in-Charge. |
| 109 | Material and labour in repair for MCB SPN 63 Amp, 240V with 10KA breaking capacity of 'C' series in distribution boards complete all as specified and as directed by Engineer-in-Charge. |
| 110 | Supply and fix to MCB SP 6-32 Amp with 10KA breaking capacity of 'C' series in distribution boards with all accessories complete all as specified and as directed by Engineer-in-Charge. |
| 111 | Dismantling and Taking down old u/s street / building sequrity Light fittings from poles, flood lights, post top lantern lights and garden lights for replacement with LED fittings complete all as specified and as directed by Engineer-in-Charge. |
| 112 | Supply and fix inrepair LED street light fitting 35 Watt 230 V AC outdoor type with high pressure die cast aluminum hosing and heat resistant complete with driver, lamp bracket with impact and corrosion resistant including thermal management in multiple optics complete with IP 65/66 protection complete all as specified and as directed by Engineer-in-Charge. |
| 113 | Material and labour for GI bracket 1.5 mtr long made out of GI pipe 40mm dia bend to suitable radius incl clamps nuts bolts washers incl painting with aluminum paint etc complete all as specified and as directed by Engineer-in-Charge. |
| 114 | Supply and fix electric water heater,storage type steel body with copper inner tank and heating element upto 2 KW capacity 25 litre, BEE 5 Star rated complete with all accessoriessuch as safety valve, thermostate, NRV, connection piece etc. complete all as specified and as directed by Engineer-in-Charge. |
| 115 | Supply and fix exhaust fan made of sturdy Engineering plastic complete with louvers shutter, voltage 230V, 50 Hz RPM 1200, Copper winding of sweep 300mm sweep with, blades, and frame and louvers complete all as specified and as directed by Engineer-in-Charge. |
| 116 | Air termination, single pointed, copper rod 12mm dia and 300mm long different locations / building complete all as specified and as directed by Engineer-in-Charge. |
| 117 | Test point terminal block made of gun metal or phosphorus bronze size 75x75x25mm drilled and screwed including 3 nos. 8mm dia 25mm long hexagonal head screw complete all as specified and as directed by Engineer-in-Charge. |
| 118 | Supply and fix Galvanised earth lead wire 4.0mm dia for roof conductors and down conductors above ground complete all as specified and as directed by Engineer-in-Charge. |
| 119 | Supply and fix or laying 32 mm light grade GI Tubes in trenches/on wall/ poles/ structures as in repairs GI tubeing light grade for road crossing/ for cable protection / fixing of pigmi lights etc, of the folling size including necessary provision for cable / Strip entry if reqd in pigmi lights pole fixinf screws / clmp complete as required complete all as specified and as directed by Engineer-in-Charge. |
| 120 | Material and labour for Earthing complete with galvanised steel earth plate electrode of size (600 x 600 x 6) mm thick buried directly into ground vertically to depth not less than 2.25 metre below normal ground level with top edge of earth plate at a depth not less than 1.5 metre below normal ground level, surrounded on all sides by alternate layers of 150 mm thick charcoal and common salt, connected to MS galvanised earth lead wire 4.0mm dia by means of bolts, nuts, washer, check nuts of galvanised iron or steel all as shown in Electrical plate No. 3, GI strip laid in dia 40 mm bore light grade GI Pipe laid in floor and fixed to wall with proper size of clamps and watering pipe of bore 20 mm dia GI light grade including wire mesh funnel, PCC, earth chamber pit (30X30X30cm) with PCC 1:2:4 type B-1 using 20 mm grade stone aggreate including form work cement mortar including CI Pit cover with frame necessary excavation and earth work in any type of soil including testing on completion for desired result complete all as specified and as directed by Engineer-in-Charge. |
| 121 | Material and labour for Earthing complete with galvanised steel earth plate electrode of size (600 x 600 x 6) mm thick buried directly into ground vertically to depth not less than 2.25 metre below normal ground level with top edge of earth plate at a depth not less than 1.5 metre below normal ground level, surrounded on all sides by alternate layers of 150 mm thick charcoal and common salt, connected to MS galvanised iron strip 25×4mm as earthing lead by means of bolts, nuts, washer, check nuts of galvanised iron or steel all as shown in Electrical plate No. 3, GI strip laid in dia 40 mm bore light grade GI Pipe laid in floor and fixed to wall with proper size of clamps and watering pipe of bore 20 mm dia GI light grade including wire mesh funnel, PCC, earth chamber pit (30X30X30cm) with PCC 1:2:4 type B-1 using 20 mm grade stone aggreate including form work cement mortar including CI Pit cover with frame necessary excavation and earth work in any type of soil including testing on completion for desired result complete all as specified and as directed by Engineer-in-Charge. |
| 122 | Supply and fix in replacement of existing worn out ceiling light with enviromental friendly, new generation, aesthetically designed, ultra modern recessed mounted LED light luminaries of size 595 mm x 595 mm(2'x2') an independent Isolated, electronic LED driver (SMPS based constant current supply) housed in CRCA powder coated sheet of system wattage - 36/40/42 Watt, Lumen out put- 4000-4300 Lm, THD < 10%, PF > 0.9, having short circuit and surge protection suitable for Armstrong/ Grid ceiling with all connected accessories including making connection with three core PVC insulated, sheathed copper conductor cable of size 23/0.0076 complete all as specified and as directed by Engineer-in-Charge. |
| 123 | Supply and fix in repair of round slim panel LED light 12W of 168mmx15mm complete all as specified and as directed by Engineer-in-Charge. |
| 124 | Supply and fix in repair of spot/ focus LED light 7W of 85mmx60mm complete all as specified and as directed by Engineer-in-Charge. |
| 125 | Supply and fix in repair of decorative light with lamp for wall incl bulb of 9/12W of different color complete all as specified and as directed by Engineer-in-Charge. |
| 126 | Supply and fix in repair of exhaust fan, engineering plastic body complete with louvers shutter, voltage 230V, 50 Hz, RPM 1200, Copper winding of sweep 250mm AC single phase with, blades, and frame and louvers of size 250 mm sweep complete all as specified and as directed by Engineer-in-Charge. |
| 127 | Supply and install wall mounted electric chimney of (LxWxH) (89.5 x 48.5 x 74.5) cm with filterless or Heat auto clean technology , suction capacity/power of 2400 m3/hr making it fume free, sensor control with Touch, Gesture and Remote control, oil collector tray, BLDC motor, Heat sensor, Intelliclean feature, LPG leakage sensor etc incl proper installation of chimney with wall clamp and of outer side fume duct with electric connection required as per site complete all as specified and as directed by Engineer-in-Charge. |
| 128 | Supply, laying and testing cable XLPE Insulated ,screened, PVC bedded, galvanized steel strip or wire armoured, electric power cables (heavy duty) 1100 Volts grade with stranded aluminium conductor of size 16 sq mm 4 core |
| 129 | Excavation in trenches not exceeding 1.5 m wide and not exceeding 1.5 m in depth for taking out pipe line etc for repairs / laying cables etc and getting out in soft / loose soil complete all as specified and as directed by the Engineer - in - Charge. |
| 130 | Material and labour for un reinforced pre cast concrete cable cover class LV type I, flat size 250 mm x 150 mm x 40 mm. |
| 131 | Sand cushioning to under ground cable complete all as specified in clause 19.75 of SSR Part - I. |
| 132 | Dismantling and Taking down LT U/S panels incl all outgoing and incoming connections and making good the disturbed area from site all as specified and directed by Engineer-in-Charge. |
| 133 | M&L for Busbar chambers with 4 aluminium busbar strip of rating 400 Amp 6 way fixed on angle iron of size 40mm x40mm x5mm Including busbar complete all as specified and directed by Engineer in Charge. |
| 134 | M & L for Earthing complete with galvanised steel earth plate electrode of size (600 x 600 x 6.3) mm thick buried directly into ground vertically to depth not less than 2.25 metre below normal ground level with top edge of earth plate at a depth not less than 1.5 metre below normal ground level, surrounded on all sides by alternate layers of 150 mm thick charcoal and common salt, connected to MS galvanized earh strip of size 32 x 6 mm by means of lugs, bolts, nuts, washer, check nuts of galvanised iron or steel all as shown in Electrical plate No. 3, wire protected by dia 15 mm bore light grade GI Pipe laid in floor and fixed to wall with proper size of clamps and watering pipe of bore 20 mm dia GI light grade including wire mesh funnel, PCC, earth chamber pit with PCC 1:2:4 type B-1 using 20 mm grade stone aggreate including form work cement mortar including CI Pit cover with frame necessary excavation and earth work in any type of soil including testing on completion for desired result all as specified. Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Sep 23, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedOct 15, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 13 daysOct 16, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 14 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender