Tender For Special Repairs Of Bldg No P-50 Of Otm Accn Of 5 Rajput Under Ge (South) Delhi Cantt-10
Tender Value
66.25 Lakhs
Estimated cost
Bid Submission
21 Oct 2026
21 days left
EMD
1.24 Lakhs
Bank guarantee accepted
Document Fee
1000
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
New Delhi → Delhi
EMD Exemption
Not Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender For Special Repairs Of Bldg No P-50 Of Otm Accn Of 5 Rajput Under Ge (South) Delhi Cantt-10
BOQ
| Sl. No. | Item Description |
| 1 | M&L for complete removal of existing treatment on wall/roof projections including facia, cornices etc by scrapping with mechancical sander(having mechanical vacuum mechanism) having RPM not less than 1500, sanding pad of 80 grit having dia of 7\\"/9\\" to make free from dust, loose paint etc by skilled labour complete all as specified and directed. |
| 2 | M&L for water proof cement based putty @1kg (undiluted) per sqm of average thickness 2mm over the plastered /old prepared painted surface of wall and sanding of the putty surface with mechanical wall sander (having mechanical vacuum mecghanism) having RPM not less than 1500, sanding pad of 240 grit or above to make the surface . Step 1: Mix the putty powder by adding water as manufacturer's instruction and mix it with putty mixer with the mixing capacity of min 2.5 kg putty per minute. Step 2: Apply the first coat of the prepared mixer with the help of fully automatic airless spray machine/manully of putty application finishing the surface even and smooth in level without any undulations. Step 3: Allow 6-8 hrs time to dry the putty surface. |
| 3 | M&L for one coat of acrylic water based exterior grade primer @ 0.9litre(undiluted)/ 10 sqm diluted with water in 1:1 ratio to be applied with fully automatic airless spray machine and allow 6-8 hours to dry the surface for painting of subsequent coats complete all as specified and directed. |
| 4 | M&L for roof treatment in following stages complete all as specified and as directed. |
| 5 | (i) Preparation of concrete surfaces by wire brush and cleaned top surfaces of cement concrete. |
| 6 | (ii) PCC type B-0, 1:2:4 (12.5mm gradded aggregate) to maintain slop as in roof padding alongwith liquid water proffing compound. |
| 7 | (iii) Rendering 15mm thick in CM 1:3 on concrete surfaces on roof, Chajja, parapet, shunkan, etc. |
| 8 | (iv) Supply only liquid water proofing compound, complete all as specified and directed by engineer-in-charge. |
| 9 | (v) M & L single component solvent based moisture cured polyurethane resin based low viscous highly penetrative primer to be mixed properly with electric mixture and to be applied by brush/roller over the entire surface. The deposition of primer should be minimum 200 ml/sqm, however the same can be varied based upon surface porosity. |
| 10 | (vi) M & L two coats of single component non-UV resistant based polyurethane to be applied over the primed surface in an interval of 4–6 hrs. The topcoats should be applied with brush/roller. No dilution is required for these two coats. A non-woven geotextile sheet of 60 GSM to be sandwiched between the layers. The deposition of PU should be 1.80 kg/Sqm providing avg thickness of 1.20 mm. The tensile strength of the product should be minimum 1.80 N/mm². The elongation of the free film should be minimum 650% as per ASTM D412, shore A hardness should be minimum 45 as per ASTM D-2240, Crack Bridging @ -9°C minimum 1.50 as per ASTM C 836 / C-836, Solid Content should not be less than 90%. Moreover, the material should confirm to ASTM C-836, ASTM C-898. |
| 11 | (vii) M & L Separation Layer—Loosely lay minimum 150 GSM Geotextile (non-woven polyester) with a minimum of 75 mm wide overlap for protection of the installed system. |
| 12 | (viii)M & L SRI Coating: Applying two coats of a fiber-reinforced liquid applied elastomeric waterproofing membrane with Polyurethane modified binder & impregnated with synthetic fibre to be applied over the self-primed surface in an interval of 4–6 hrs. The topcoats should be applied with brush / roller / spray. The deposition should be minimum 1.20 kg/sqm. The crack bridging of the product should be minimum 1.50 mm & SRI value should be greater than 106. The priming coat should be self-priming with dilution of 40% with potable water. This layer includes 1 priming coat + 2 undiluted topcoats. |
| 13 | Taking down chowkats with shutters not exceeding 1.50 Sqm each (without taking off shutters from the frames) complete all as specified and as directed. |
| 14 | Taking down chowkats with shutters exc 1.50 Sqm but n exc 4.00 Sqm each (without taking off shutters from the frames) complete all as specified and as directed. |
| 15 | M & L Factory made single extruded WPC (Wood Polymer Composite) solid door/window/ceostory windows & other decorated type frames/chowkhat of size 100 × 65 mm comprising of virgin PVC polymer, calcium carbonate and natural fibres (wood powder/rice husk/wheat husk) and non-toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with mitre joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum screw withdrawal strength of 750 kg, minimum compressive strength of 58 N/mm², modulus of elasticity 900 N/mm² and resistance to spread of flame of Class A category with property of being termite/borer proof, waterproof, moisture proof and fire retardant and fixed in position with MS holdfast lugs/SS dash fasteners of required dia and length complete as per direction of Engineer-in-Charge. (MS hold fast/SS dash fasteners shall be paid separately.)Note: For WPC solid door/window frames, minus 5 mm tolerance in dimension i.e. depth and width of profile shall be acceptable but no extra payment on this account shall be made. |
| 16 | M & L Factory made single extruded WPC (Wood Polymer Composite) solid door/window/ceostory windows & other decorated type frames/chowkhat of size 125 × 65 mm comprising of virgin PVC polymer, calcium carbonate and natural fibres (wood powder/rice husk/wheat husk) and non-toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with mitre joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum screw withdrawal strength of 750 kg, minimum compressive strength of 58 N/mm², modulus of elasticity 900 N/mm² and resistance to spread of flame of Class A category with property of being termite/borer proof, waterproof, moisture proof and fire retardant and fixed in position with MS holdfast lugs/SS dash fasteners of required dia and length complete as per direction of Engineer-in-Charge. (MS hold fast/SS dash fasteners shall be paid separately.)Note: Minus 5 mm tolerance in profile dimensions is acceptable. |
| 17 | S & F providing and fixing factory made single extruded WPC (Wood Polymer Composite) solid decorative type flush door shutter 30 mm thick comprising of virgin PVC polymer, calcium carbonate and natural fibres (wood powder/rice husk/wheat husk) and non-toxic additives (maximum toxicity index of 12 for 100 gms), having minimum density of 650 kg/cum, screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength of 50 N/mm², modulus of elasticity 850 N/mm² and resistance to spread of flame Class A, termite/borer proof, waterproof, moisture proof and fire retardant, WPC laminated with PVC foil on both faces, fixed with stainless steel but hinges and necessary SS screws complete as directed by Engineer-in-Charge. (Stainless steel butt hinges and necessary SS screws shall be paid separately.) |
| 18 | S & F Providing and fixing factory made single extruded WPC (Wood Polymer Composite) solid decorative type flush door shutter of size 35 mm thick comprising of virgin polymer of K value 58–60 (Suspension Grade), calcium carbonate and natural fibres (wood powder/rice husk/wheat husk) and non-toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm², modulus of elasticity 850 N/mm² and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant.WPC to be laminated with PVC foil of minimum 14 microns thick of approved design pasted with hot melt adhesive on both faces of shutter and fixed with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S. screws, all as per direction of Engineer-in-Charge.Note: Stainless steel butt hinges and necessary S.S. screws shall be paid separate |
| 19 | Providing 30 mm thick factory-made wire mesh solid WPC doors shutter consisting of Density 650 kg/cum manufactured by an ISO-9001:2015 certified company. Door to be panelled with SS mosquito mesh and XTNL aluminium mesh for additional strength and safety purpose. Door to be fixed to frame with 3 Nos. SS butt hinges (100 × 25 × 2 mm and 32 mm long steel screws), complete with handles, tower bolts, etc., complete all as per Engineer-in-Charge's specification and drawings. Fixture/fittings shall be measured and paid under relevant items. |
| 20 | S&F for steel windows fabricated from roll formed sections made of galvanized steel colour coated powder coated (Base steel as per IS-513 D quality galvanized as IS 277 with zinc coating of 120 GSM) with total coated thickness of 0.60 mm. The coated section shall be with primer coated of primer of 7 microns thick, finish painted with a polyester paint of 12.16 microns thick and back coated with alkyd backer of 5–7 microns or powder coated with pure polyester powder upto 50–60 microns thick with the following specifications:(a) Main frame: 72 mm × 55 mm × 0.58 mm(b) Mullion: 72 mm × 50 mm × 0.58 mm(c) Glazed / gauzed shutter frame: 47 mm × 20.20 mm × 0.58 mm(d) Glass beads size: 12 mm × 12 mm × 0.58 mmAccessories: Each shutter shall be provided with the following fittings:Stainless steel pipe hinges – 01 setAluminium powder coated handles – 04 Nos.Glass panes – glazed shutter fixed with 5.00 mm thick float glassWire mesh – Stainless steel wire mesh of 0.3 mm nominal dia wire and average aperture width 1.40 mmGrills window shall be provided with grill made of 10 mm square MS bars welded to 12 mm × 6 mm thick MS plate. Distance between bars should not be more than 12 cm c/c.Total grill unit shall be enamel painted and fixed to window frame with screw.Note: The glazed/gauged shutter including guard bars shall be measured once, i.e., as per area of opening. No separate payment for separate shutter, i.e., glazed and fly-proof and guard bars, shall be made. Area of shutter shall be the area of opening. |
| 21 | S & F in repair aluminium ventilator with outer frame 40 × 14 mm, 1.3 mm thick corners cut and aluminium welded, centre mullion 40 × 65 mm, glazing clips, beading screws, MS wire mesh, 3 mm thick sheet glass, providing anodised aluminium snap beading and fixing complete. |
| 22 | Supply only stainless steel wire cloth 0.36 mm nominal dia of wire and average width of aperture 1.40 mm complete all as specified and directed. |
| 23 | S & F 100 mm size butt hinges, stainless steel of AISI 304 complete all as specified and directed. |
| 24 | S & F stainless steel of AISI 304 grade barrel tower bolt 200 mm long, extruded section, etc., complete all as specified and directed. |
| 25 | S & F stainless steel of AISI 304 grade barrel tower bolt 150 mm long, extruded section, etc., complete all as specified and directed. |
| 26 | S & F stainless steel of AISI 304 grade sliding door bolt with hasp, staple (both type) and fixing clips of SS 300 grade, cast or extruded sections, and fixing bolts etc., complete all as specified and directed. |
| 27 | S & F stainless steel of AISI 304 grade handle of size 200 mm long etc., complete all as specified and directed. |
| 28 | S & F 150 mm long floor door stopper of aluminium alloy, hard drawn steel spring, fixed in floor complete all as specified and directed. |
| 29 | Injection Grouting Treatment for Damp MasonryExpose the first joint of masonry structure at ground level horizontally. The plaster shall be knocked off at least 50 cm beyond the visibly penetrated area. Damaged mortar joints are to be scraped out to a depth of 15 mm.Drilling Holes: Drill 10 mm diameter holes in masonry structure along the side of the joint as per IS code at an angle of 45° and at spacing of 15–30 cm depending on the extent of rising dampness as recommended by Engineer-in-Charge.Cleaning of Holes: Clean holes by air blower prior to fixing nozzles. Install latex polymer injection packers (9.8 mm dia × 100 mm long) and tighten securely using spanner.Supply and Apply: Three-part, very low viscosity elastic polyacrylic injection resin with versatile and controlled expansion behaviour reacting with water (temperature range +3°C to +40°C), gel time approx. 8.5 minutes, pH 9–10, suitable for reinjectable hose systems.The holes shall be drilled until reaching behind the wall/floor interface. Inject resin at >20 bar into cracks or masonry joints allowing water ingress.Inject a small amount of water before grouting. When movement stops or polymer deactivates, inject grout. If dampness is heavy, inject again.Average resin consumption: 200 ml per hole.Complete all as specified and directed. |
| 30 | Supply and apply a three-part, very low viscosity elastic polyacrylic injection resin with versatile and controlled expansion behaviour reacting with water (temperature range +3°C to +40°C), gel time approximately 8.5 minutes, pH 9–10, tested as per WTA No. 2002-094 (1A), for reinjectable hose systems.The holes shall be drilled until reaching behind the wall/floor interface. Inject resin compound at pressure greater than 20 bar into cracks, fissures or masonry joints allowing water ingress.Water shall be injected before grouting. When movement stops, inject grout. Heavy dampness shall receive a second injection.Average resin consumption: 200 ml per hole. |
| 31 | M & L for providing anti-termite treatment along the external wall below concrete apron for post-construction treatment by chemical emulsion @ 2.25 litres per linear metre including drilling and plugging holes etc. in apron. |
| 32 | M & L injecting chemical emulsion into masonry with emulsifiable concentrate @ one litre per hole, 300 mm apart including drilling and plugging 12 mm dia holes with cement mortar 1:2 to match existing floors, complete all as specified. |
| 33 | M & L for chipping of spalled and loose concrete and cleaning rust from reinforcement by sand blasting, scrubbing down concrete surface with wire brushes, cleaning with water, allowing to dry, and applying a layer of zinc rich epoxy primer as anti-rust on all exposed reinforcement, followed by applying a layer of approved epoxy adhesive on complete exposed surfaces of concrete to be gunited and applying two layers of guniting over steel welded mesh 2 mm dia wire and aperture 75 mm, total thickness of gunite not exceeding 25 mm (average 13 mm) with cement mortar 1:2 using OPC 53 grade cement mixed with polycrete admixture @ 2% by weight of cement or as per manufacturer's instructions, and finally applying cement plaster over gunite surface of required thickness to give even, uniform and smooth finish conforming to proper cement mortar (1:3) to match the existing surfaces including all sides and soffits of slabs, chajjas, fins, facias, parapets, columns and beams, etc., complete including scaffolding, shuttering, necessary chases to brick work or RCC members at any height up to 4-storey buildings, all as specified.Note: Steel welded mesh is to be tightened/welded with the existing reinforcement. The cost of welded mesh is deemed to be included in the unit rate quoted. |
| 34 | Demolition of brickwork or stone/boulder masonry built in cement or cement-lime mortar including all quoins, arches, pillars, etc., but excluding ashlar facing, dressed stonework and precast concrete articles. |
| 35 | M & L brickwork with sub-class 'B' bricks, straight or curved on plan exceeding 6 m mean radius built in cement mortar (1:4), complete all as specified and directed |
| 36 | M & L half brick masonry with sub-class 'B' bricks, straight or curved on plan to any radius in half brick thick walls built in cement mortar (1:4), complete all as specified and directed. |
| 37 | Taking down cement or cement lime plaster, any description, on brick or stone walls, etc including raking out joints, hacking for key, scrubbing down with water etc complete. |
| 38 | M & L for 15 mm thick ready mixed plaster (self-curing) on brick/concrete surfaces of external walls, finished even and smooth, without using extra cement, complete all as specified and directed. |
| 39 | M & L for 15 mm thick ready mix plaster (self-curing) on brick/concrete surface of internal walls, finished even and smooth without using extra cement, complete all as specified and directed. |
| 40 | M & L for 10 mm thick ready mix plaster (self-curing) on ceiling surfaces/internal walls, finished even and smooth, complete all as specified and directed by Engineer-in-Charge. |
| 41 | Demolition of cement concrete( un reinforced) in ground floors and pavings n exc 15 cm thickness (below or above ground level) |
| 42 | Demolition of cement concrete (reinforced) of any description and in any position not otherwise specifically provided for. |
| 43 | Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises, complete all as specified and directed. |
| 44 | M & L providing 10 mm thick granite slab (square/rectangular), polished, area of each tile exceeding 0.42 sqm but not exceeding 1.00 sqm (600 mm × 1200 mm), set and jointed in cement mortar (1:3) including 20 mm thick backing in cement mortar (1:4), complete all as specified and directed. |
| 45 | All as per Item No. 36 but as skirting including 10 mm thick backing coat CM 1:3, complete all as specified and directed. |
| 46 | M & L non-skid coloured ceramic tiles 7–8 mm thick (square/rectangular), area of each tile exceeding 0.11 sqm but not exceeding 0.38 sqm, set and jointed in neat white or coloured cement slurry and pointed in white or coloured cement to match over and including 15 mm thick screed bed in cement mortar (1:4), complete all as specified and directed. |
| 47 | M & L glazed ceramic coloured tiles in vertical surfaces, size 600 × 300 × 7 mm, set and jointed in neat white or coloured cement slurry and pointed in white or coloured cement to match over and including 10 mm thick plaster in cement mortar (1:4), complete all as specified and directed. |
| 48 | Demolition of stone slabs and tiles laid, bedded and pointed of any description or thickness in floors, aprons, etc. |
| 49 | M & L granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, window sills, cooking platforms, vanity counters and like work in cement mortar (1:4) screed bed 20mm, including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite , complete all as specified and directed. |
| 50 | M & L granite colour approved (of any type) work (table rubbed and polished) in wall lining, veneer work and similar locations using 12 mm thick in cement mortar (1:3) including pointing in white cement (1:2) using marble dust with admixture of pigment to match the shade of granite, complete all as specified and directed. |
| 51 | M & L machine-cut Kota stone slab flooring over and including 20 mm thick cement screed bed in cement mortar (1:4), laid and jointed with grey cement slurry mixed with pigment to match the shade of slab including rubbing and polishing, complete all as specified and directed. |
| 52 | M & L Kota stone slab in treads, skirting, dado and pillar laid over and including 10 mm thick cement plaster in cement mortar (1:3), laid and jointed with grey cement slurry mixed with pigment to match the shade of slab including rubbing and polishing, complete all as specified and directed. |
| 53 | M & L 25 mm thick levelling cement concrete type B-1, 1:2:4 (20mm graded aggregate) under tiles/stones complete all as specified and directed. |
| 54 | M & L Cement Concrete 1:3:6, Type C-1 (using 20 mm graded stone aggregate) in lintels up to 1.5 m clear span, bands, copings, kneelers, apex stones, bed plates, water troughs and the like including weathering, slightly rounded or chamfered angles, throating, complete all as specified and directed. |
| 55 | M & L Cement Concrete 1:2:4, Type B-1 (using 12.5 mm graded stone aggregate) in lintels up to 1.5 m clear span, bands, copings, kneelers, apex stones, bed plates, water troughs and the like including weathering, slightly rounded or chamfered angles and throating, complete all as specified and directed. |
| 56 | Mild steel reinforcement bars, cut to length, bent to shape as required including cranking, bending spirally for hooping for columns, hooking ends, binders, ties, rings, etc., and binding with and including mild steel wire (annealed) not less than 0.90 mm diameter or securing with clips, complete all as specified. |
| 57 | Taking down eaves gutters and rainwater pipes (any size or pattern), including all fittings, heads, shoes, bends, swan necks and other accessories, for refixing or removal to store (measured overall as fixed along the centre line over fittings and accessories). |
| 58 | S & F PVC (SWR) pipes, single socketed, in any length with rubber ring joints, fixed to walls, of 75 mm bore complete all as specified and directed. |
| 59 | S & F PVC (SWR) pipes, single socketed, in any length with rubber ring joints, fixed to walls, of 110 mm bore complete all as specified and directed. |
| 60 | S & F PVC (SWR) pipes, single socketed, in any length with rubber ring joints, laid in trenches or in floors, of 75 mm bore complete. |
| 61 | S & F PVC (SWR) pipes, single socketed, in any length with rubber ring joints, laid in trenches or in floors, of 110 mm bore complete. |
| 62 | S & F PVC (SWR) bends, any radius, 75 mm bore, complete. |
| 63 | S & F PVC (SWR) bends, any radius, 110 mm bore, complete. |
| 64 | S & F PVC (SWR) junction single (single 'T'), equal or unequal, 75 mm bore, complete. |
| 65 | S & F PVC (SWR) junction single (single 'T'), equal or unequal, 110 mm bore, complete. |
| 66 | S & F PVC (SWR) junction single (single 'Y'), equal or unequal, 110 mm bore, complete. |
| 67 | S & F PVC (SWR) vent cowl, 110 mm bore, complete. |
| 68 | S & F PVC (SWR) plain end pipe laid in trench including solvent cement complete and concrete 1:2:4 Type B-1 using 20 mm graded stone aggregate with WPC, complete all as specified and directed. |
| 69 | Supplying and fixing of CPVC pipes (40 mm outer dia) SDR 11 & Plain CPVC SDR 11 fittings in trenches/walls, including all plain CPVC fittings and pipe cutting, fixing with CPVC solvent cement and testing, including taking up or down 32 mm bore GI tubing and connections, complete all as specified. |
| 70 | Supplying and fixing of CPVC pipes (32 mm outer dia) SDR 11 & Plain CPVC SDR 11 fittings in trenches/walls, including all plain CPVC fittings and pipe cutting, fixing with CPVC solvent cement and testing, including taking up or down 25 mm bore GI tubing and connections, complete all as specified. |
| 71 | Supplying and fixing of CPVC pipes (25 mm outer dia) SDR 11 & Plain CPVC SDR 11 fittings in trenches/walls, including all plain CPVC fittings and pipe cutting, fixing with CPVC solvent cement and testing, including taking up or down 20 mm bore GI tubing and connections, complete all as specified. |
| 72 | Supplying and fixing of CPVC pipes (20 mm outer dia) SDR 11 & Plain CPVC SDR 11 fittings in trenches/walls, including all plain CPVC fittings and pipe cutting, fixing with CPVC solvent cement and testing, including taking up or down 15 mm bore GI tubing and connections, complete all as specified. |
| 73 | Supply only special fittings 40 mm outer dia Brass Elbow |
| 74 | Supply only special fittings 32 mm outer dia Brass Elbow. |
| 75 | Supply only special fittings 25 mm outer dia Brass Elbow |
| 76 | Supply only special fittings 20 mm outer dia Brass Elbow. |
| 77 | Supply only special fittings 40 mm outer dia Male Brass Threaded Adaptor (MTA/MBTA). |
| 78 | Supply only special fittings 32 mm outer dia Male Brass Threaded Adaptor (MTA/MBTA). |
| 79 | Supply only special fittings 20 mm outer dia Male Brass Threaded Adaptor (MTA/MBTA) |
| 80 | Supply only special fittings 40 mm outer dia Brass Ball Valve for CPVC pipe, fixed complete. |
| 81 | Supply only special fittings 32 mm outer dia Brass Ball Valve for CPVC pipe, fixed complete. |
| 82 | Supply only special fittings 25 mm outer dia Brass Ball Valve for CPVC pipe, fixed complete |
| 83 | Supply only special fittings 40 mm outer dia Brass Tee for CPVC pipe, fixed complete. |
| 84 | Supply only special fittings 32 mm outer dia Brass Tank Adaptor for CPVC pipe/Tank, fixed complete. |
| 85 | Supply only special fittings 25 mm outer dia Brass Tank Adaptor for CPVC pipe/Tank, fixed complete. |
| 86 | M & L cutting chases, pinning in, making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc.; and cutting chases for concealed water tubing or concealed conduit wiring, etc., and making good, cutting not exceeding 10 cm girth, complete all as specified |
| 87 | M&L for rotational moulded polyethylene water storage tanks white colour 1000 lts capacity, triple layered (cylindrical vertical with closed top) hoisted and fixed in position including 20 mm dia PTMT float valve, lid tank cover for polyethylene and polyethylene ball including taking out existing unserviceable overhead tank of any description including fitting and fixtures, complete all as specified & directed. |
| 88 | S&F in repair vitreous china squatting pan, 'Orissa' pattern, of size 580 mm × 440 mm white with integral foot rest complete including provn of cement concrete bedding and connection to trap, outgoing flushing pipe, anti syphonage pipe etc complete. |
| 89 | S&F in repair Vitreous china wash down water closet pan (pedestal pattern), white, complete including fixing to trap, Inlet Supply and fixing of PVC seat and cover for pedestal pan complete all as specified and as directed. |
| 90 | S&F in repair 10 litre capacity PVC low level cistern 'white' with inlet, float valve including bracket with 32mm dia PVC waste/flush pipe 600 mm long complete. |
| 91 | S & F PVC connection 600mm long and 15 mm dia with brass fly nut at both ends complete. |
| 92 | S & F in repair vitreous China urinal Half stall type, white with grating and unions for discharge pipe including providing and fixing plugs, bedding urinal with 15 mm bore urinal spreader and waste coupling of PTMT min wt for urinal for urinals, (Minimum weight 320gm), & waste pipe against wall in CM 1:2 securing urinal to plugs with and including 60mm long brass screws pointing around urinal back in cement complete all as specified. |
| 93 | S & F vitreous china wash hand basin white, flat back of size 550mm × 400mm fixed on and including cast iron cantilever bracket, 32mm dia brass waste coupling and 32 mm dia PVC waste pipe including fixing of tap, waste fitting etc complete. Note: Pillar tap shall be measured as supply only under respective item. |
| 94 | S & F in repair Stop valves, cast copper alloy, screwed down, high pressure, with crutch or butterfly handle, fancy type, chromium plated, with long shank and cup (concealed type) screwed both ends for iron pipe or for unions 15 mm bore complete. |
| 95 | S & F in repair Stop valves, cast copper alloy, screwed down, high pressure, with crutch or butterfly handle, fancy type, chromium plated, screwed both ends for iron pipe or for unions 15 mm bore complete. |
| 96 | S & F in repair Bib taps cast copper alloy chromium plated with crutch or butterfly handle, fancy type, screwed down, screwed for iron pipe or for brass ferrule 15 mm bore complete. |
| 97 | S&F in repair fancy type brass chromium plated shower rose with arm complete. |
| 98 | S & F health faucet (ABS Body) mild steel chromium plated suitable for 15mm dia pipe with 1.25 metre long flexible tube and ABS wall hook including making connections and fixed in position complete in all respect as specified. |
| 99 | S&F looking mirror of size 600mm × 450mm with 5 mm thick mirror of selected quality glass, mounted on plastic frame and fixed complete. |
| 100 | S & F in repair Soap dish disc (oval) type, mild steel chromium plated of approximate size 100 × 50 × 10 mm, complete. |
| 101 | S&F in repair Granite corner (round quarter) Shelf (Shower Caddy), 23 cm rounded with moulding, a convex shaped trim with cross section in the shape of a quarter circle, and fix at corner complete all as specified by Engineer-in-Charge. |
| 102 | S & F in repair Tubular towel rail of brass chromium plated, 20 mm dia, 'D' type, 60 cm long between flanges complete. |
| 103 | Supply & fixed Vitreous China urinal partition white of size 310 × 700 mm complete. |
| 104 | S & F in repairs 15 mm bore pillar cock fancy type, screwed down high pressure with or without letters hot or cold with long screwed shank and fly nuts screwed for iron pipe ISI marked add if fixed in repairs complete all as specified & directed. |
| 105 | M & L for Preparing new plastered or unplastered surfaces of ceiling and applying three coats of white wash complete. |
| 106 | M & L for Preparing old plastered or unplastered surfaces of ceiling and applying two coats of white wash complete. |
| 107 | M & L for Preparing new plastered surfaces of wall and applying two coats of oil bound distemper white or tinted over and including 1 mm thick wall care putty and chalk whiting on plastered surfaces preparatory to distempering complete. |
| 108 | M & L for Preparing old plastered surfaces of wall and applying two coats of oil bound distemper white or tinted over and including 1–1.5 mm thick wall care putty on plastered surfaces preparatory to distempering complete. |
| 109 | M&l for complete removal of existing treatment of wall including cornices etc by washing, rubbing down, stopping holes and applying two coats of cement base paint of approved shade complete all as specified and directed |
| 110 | M&l for preparation of new plastered surfaces of wall and applying two coats of cement base paint of approved shade over a shade of cement based primercomplete all as specified and directed |
| 111 | M & L applying one coats of synthetic enamel paint on old treated wooden surfaces of any description over 10 cm width or girth including preparation of surfaces complete. |
| 112 | M & L applying two coats of synthetic enamel paint on new wooden surfaces of any description over 10 cm width or girth over a coat of pink primer including preparation of surfaces complete. |
| 113 | M & L applying one coat of synthetic enamel paint on old treated steel surfaces of any description over 10 cm width or girth including preparation of old painted surfaces complete. |
| 114 | M & L applying two coats of synthetic enamel paint on new steel surfaces of any description over 10 cm width or girth over a coat of red oxide primer including preparation of steel surfaces complete. |
| 115 | Taking down carefully the old U/S copper point wiring (light, fan, socket or power) complete fitting such as switches, ceiling roses, pendants, sockets, regulators, bell, etc and making good disturbed surfaces of walls including necessary touch up with the adjoining surface of disturbed area ie with OBD/colour wash/white wash as the existing finish complete. |
| 116 | M&L for point wiring complete, stranded copper conductor 1.5 Sqmm nominal area PVC insulated FRLS 1100 volts grade electrical cable in but with through suitable concealed PVC conduit and including replacement of modular sunken pressed steel terminal boxes 2mm thick of required size and modular white cover plate with all accessories including 1.5 sqmm stranded copper conductor PVC unsheathed cable earth wire to common earth and connected to earth dolly complete and making good to disturbed surface of walls including necessary touch up with adjoining surface of disturbed area i.e with OBD/colour work/white wash as existing finishes complete all as specified and as directed.Note :- 1. The Rate is inclusive cutting/chasing and making good distrubed surface with CM 1:3 and same surface finishes with the adjoining surface of distribed area with ODB/colour wash/white wash complete.2. At roof slab where there is burnt/blockage in the existing conduit wiring will be done through PVC conduit and rate are inclusive in above quoted item. |
| 117 | (a) All as per item No 2 but One light /fan/Bell point/security light controlled by one way switch |
| 118 | (b) All as per item No 2 but One light controlled by two way switch |
| 119 | (c) All as per item No 2 but One 3 pin socket outlet 5 amps on same board |
| 120 | (d) All as per item No 2 but One 3 pin socket outlet 5 amps point independent board with cable 1.5 Sqmm for main current and 1.5 sqmm as earth wire as power point. |
| 121 | (e) All as per item No 2 but One 3 pin socket outlet, 15 amps on independent board with cable 2.5 Sqmm for main current and 2.5 sqmm as earth wire as power point.Notes :- One power point/AC point wiring shall be provided on one circuit of one point only. |
| 122 | M & L applying two coats of synthetic enamel paint on new steel surfaces of any description over 10 cm width or girth over a coat of red oxide primer including preparation of steel surfaces complete. |
| 123 | M & L applying two coats of synthetic enamel paint on new steel surfaces of any description over 10 cm width or girth over a coat of red oxide primer including preparation of steel surfaces complete. |
| 124 | M & L applying two coats of synthetic enamel paint on new steel surfaces of any description over 10 cm width or girth over a coat of red oxide primer including preparation of steel surfaces complete. |
| 125 | M & L applying two coats of synthetic enamel paint on new steel surfaces of any description over 10 cm width or girth over a coat of red oxide primer including preparation of steel surfaces complete. |
| 126 | M & L applying two coats of synthetic enamel paint on new steel surfaces of any description over 10 cm width or girth over a coat of red oxide primer including preparation of steel surfaces complete. |
| 127 | M & L applying two coats of synthetic enamel paint on new steel surfaces of any description over 10 cm width or girth over a coat of red oxide primer including preparation of steel surfaces complete. |
| 128 | M & L applying two coats of synthetic enamel paint on new steel surfaces of any description over 10 cm width or girth over a coat of red oxide primer including preparation of steel surfaces complete. |
| 129 | M & L applying two coats of synthetic enamel paint on new steel surfaces of any description over 10 cm width or girth over a coat of red oxide primer including preparation of steel surfaces complete. |
| 130 | M & L applying two coats of synthetic enamel paint on new steel surfaces of any description over 10 cm width or girth over a coat of red oxide primer including preparation of steel surfaces complete. |
| 131 | M & L applying two coats of synthetic enamel paint on new steel surfaces of any description over 10 cm width or girth over a coat of red oxide primer including preparation of steel surfaces complete. |
| 132 | M & L applying two coats of synthetic enamel paint on new steel surfaces of any description over 10 cm width or girth over a coat of red oxide primer including preparation of steel surfaces complete. |
| 133 | M & L applying two coats of synthetic enamel paint on new steel surfaces of any description over 10 cm width or girth over a coat of red oxide primer including preparation of steel surfaces complete. |
| 134 | M & L applying two coats of synthetic enamel paint on new steel surfaces of any description over 10 cm width or girth over a coat of red oxide primer including preparation of steel surfaces complete. |
| 135 | M & L applying two coats of synthetic enamel paint on new steel surfaces of any description over 10 cm width or girth over a coat of red oxide primer including preparation of steel surfaces complete. |
| 136 | M & L applying two coats of synthetic enamel paint on new steel surfaces of any description over 10 cm width or girth over a coat of red oxide primer including preparation of steel surfaces complete. |
| 137 | M & L applying two coats of synthetic enamel paint on new steel surfaces of any description over 10 cm width or girth over a coat of red oxide primer including preparation of steel surfaces complete. |
| 138 | M & L applying two coats of synthetic enamel paint on new steel surfaces of any description over 10 cm width or girth over a coat of red oxide primer including preparation of steel surfaces complete. |
| 139 | M & L applying two coats of synthetic enamel paint on new steel surfaces of any description over 10 cm width or girth over a coat of red oxide primer including preparation of steel surfaces complete. |
| 140 | M & L applying two coats of synthetic enamel paint on new steel surfaces of any description over 10 cm width or girth over a coat of red oxide primer including preparation of steel surfaces complete. |
| 141 | M & L applying two coats of synthetic enamel paint on new steel surfaces of any description over 10 cm width or girth over a coat of red oxide primer including preparation of steel surfaces complete. |
| 142 | M & L applying two coats of synthetic enamel paint on new steel surfaces of any description over 10 cm width or girth over a coat of red oxide primer including preparation of steel surfaces complete. |
| 143 | M & L applying two coats of synthetic enamel paint on new steel surfaces of any description over 10 cm width or girth over a coat of red oxide primer including preparation of steel surfaces complete. |
| 144 | M & L applying two coats of synthetic enamel paint on new steel surfaces of any description over 10 cm width or girth over a coat of red oxide primer including preparation of steel surfaces complete. |
| 145 | M & L applying two coats of synthetic enamel paint on new steel surfaces of any description over 10 cm width or girth over a coat of red oxide primer including preparation of steel surfaces complete. |
| 146 | M & L applying two coats of synthetic enamel paint on new steel surfaces of any description over 10 cm width or girth over a coat of red oxide primer including preparation of steel surfaces complete. |
| 147 | M & L applying one coat of synthetic enamel paint on old treated steel surfaces of any description over 10 cm width or girth including preparation of old painted surfaces complete. |
| 148 | M & L applying one coat of synthetic enamel paint on old treated steel surfaces of any description over 10 cm width or girth including preparation of old painted surfaces complete. |
| 149 | M & L applying two coats of synthetic enamel paint on new steel surfaces of any description over 10 cm width or girth over a coat of red oxide primer including preparation of steel surfaces complete. Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Sep 23, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedOct 21, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 21 daysOct 23, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 23 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender