Tender For Reconstruction Of Sluice No.2 Of Pullangudi Tank In Ramanathapuram Taluk Of Ramanathapuram District
Tender Value
9.40 Lakhs
Estimated cost
Bid Submission
08 Oct 2026
13 days left
EMD
10000
Bank guarantee accepted
Document Fee
Ref. Documents
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Ramanathapuram → Tamil Nadu
EMD Exemption
Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender For Reconstruction Of Sluice No.2 Of Pullangudi Tank In Ramanathapuram Taluk Of Ramanathapuram District
BOQ
| Sl. No. | Item Description |
| 1 | Dismantling with out damaging the near by structures if any, clearing away and carefully stacking materials useful for reuse for any thickness of walls in brick/stone masonry in cement mortar wall under 3 m high etc, complete complying with technical specification and as directed by the Engineer in charge of work |
| 2 | Dismantling with out damaging the near by structures if any, clearing away and carefully stacking materials useful for reuse for any thickness of plain cement concrete etc, complete complying with technical specification and as directed by the Engineer in charge of work |
| 3 | Earth work excavating and depositing on bank with initial lead of 10m and initial lift of 2m in hard stiff clay, stiff black cotton, hard red earth, shales, murram, gravel, stoney earth and earth mixed with small size boulders etc, complete complying with standard specification and as directed by the Engineer in charge of work.(SS.20B) |
| 4 | Earthwork excavation for foundation in hard stiff clay, stiff black cotton soil, hard red earth, shales, murram, gravel, stoney earth and earth mixed with small size boulders hard gravelly soil inclusive of shoring to full depth, strutting and bailing out water wherever necessary and refilling the sides of foundation with excavated soil other than sand in layers of not more than 15 cm thick, well rammed, consolidated and depositing the surplus earth in places as shown by the departmental officers with an initial lead of 10 metres and initial lift of 2 metres and clearing, leveling the site etc., complete complying with standard specification and as directed by the Engineer in charge of work. |
| 5 | Refilling with excavated earth (other than sand) with all leads and lifts for filling the open cut wherever necessary in layers including breaking clods watering and compaction using Power Roller to atleast 95% of Proctor Density at OMC in each layer and sectioning etc., complete complying with standard specification and as directed by the Engineer in charge of work. |
| 6 | Collection and supply of Sand Gravel mix 1:1 (one CS sand and one gravel) ratio for basement including stacking, mixing and spreading the Sand Gravel mix in layers of not exceeding in 150 mm thickness over properly prepared surface, watering and consolidating the same with approved type of compaction equipment complete complying with the standard specification and as directed by the Engineer in charge of work. |
| 7 | Providing and placing in position cement concrete of grade M15 for Plain cement concrete using hard well graded coarse aggregates of maximum nominal size of 40mm weigh batching the incredients and mixing in approved mixers/batching plant (to produce concrete of the specified characteristic strength of 15 N/sqmm at 28 days) including dewatering the placement site by bailing/pumping and by diverting wherever necessary, laying the concrete in layers of not exceeding 15cm thick and in bays, compacting and finishing the surface to the profile with all leads and lifts, water curing to attain and strength as specified in the drawing for various depth and height below and above ground level etc., complete complying with the standard specification and as directed by the Engineer in charge of work. |
| 8 | Providing and placing in position of plain cement concrete of grade M20 grade using hard well graded coarse aggregates of maximum nominal size of 20mm weigh batching the incredients and mixing in approved mixers/batching plant (to produce concrete of the specified characteristic strength of 15 N/sqmm at 28 days) including dewatering the placement site by bailing/pumping and by diverting wherever necessary, placing concrete in layers and in bays vibrarting, compacting and finishing the surface to the profile with all leads and lifts, water curing to attain and strength as specified in the drawing for various depth and height below and above ground level etc., complete complying with the standard specification and as directed by the Engineer in charge of work. ( With vibration) |
| 9 | Providing and placing in position of plain cement concrete of grade M20 using hard well graded coarse aggregates of maximum nominal size of 40mm (60%) and 20mm (40%) weigh batching the incredients and mixing in approved mixers/batching plant (to produce concrete of the specified characteristic strength of 15 N/sqmm at 28 days) including dewatering the placement site by bailing/pumping and by diverting wherever necessary, laying the concrete in layers of not exceeding 15cm thick and in bays, vibrating, compacting and finishing the surface to the profile with all leads and lifts, water curing to attain and strength as specified in the drawing for various depth and height below and above ground level etc., complete complying with the standard specification and as directed by the Engineer in charge of work. |
| 10 | Providing and placing in position of plain cement concrete of grade M20 using hard well graded coarse aggregates of maximum nominal size of 20mm weigh batching the incredients and mixing in approved mixers/batching plant (to produce concrete of the specified characteristic strength of 20 N/sqmm at 28 days) including dewatering the placement site, by bailing/pumping and by diverting wherever necessary, laying the concrete in layers of not exceeding 15cm thick and in bays, compacting and finishing the surface to the profile with all leads and lifts, water curing to attain and strength as specified in the drawing for various depth and height below and above ground level etc., complete complying with the standard specification and as directed by the Engineer in charge of work (For Wearing coat) ( Without vibration) |
| 11 | Supplying and erecting centering for sides and soffits including necessary supports and strutting upto 3.29 m height for Plane surfaces as detailed below in all floors with all cross bracings using mild steel sheets of size 90 x 60 cm and 10 BG stiffened with welded mild steel angle, of size 25 mm x 25 mm x 3 mm for boarding laid over silver oak joist of size 10cm x 6.5 cm spaced at about 90 cm centre to centre and supported by casurina props of 10cm to 13 cm dia spaced at not more than 75 cm centre to centre etc., complete complying with standard specification and as directed by the departmental officers (payment for centering shall be given after the concrete has been laid).With strutting |
| 12 | Supplying and fixing new cut stone roughly dressed to size on all faces and set in cement mortar 1:3 (One cement and three CS sand by volume) including all incidental charges such as finishing, curing etc., complete complying with standard specification and as directed by the Engineer in charge of work. |
| 13 | Fabricating and supply of country wood plug size of 40 x 40 cm and 45 cm to 60 cm height. The plug rod with 20 mm dia mild steel rod size of 3.0 m to 4.50 m height. The plug top side, middle, centre and bottom side covered iron strap - 3 nos. Plate thickness size 3 mm steel plate. The plug hole size 10 cm to 25 cm dia. etc., including cost of rod, wrought and put up and fixing in correct alignment in position. The plug painted with two coats of Varnish, the rod painted with two coats of best anti-corrosive paint and conveyance to the work site including loading, unloading. The rates should be inclusive of all taxes and duties and including fixing charges etc., complete complying specification and as directed by the Engineer. |
| 14 | Fabricating, Supplying and fixing of Top Beam made up of 150x75mm (ISMB 150) duly drilled to suit the Head Set Assembly with required bed bolt made out of 25mm mild steel round rod duly threaded with suitable anchorage arrangements to a height of 0.60m with necessary Fish plate made out of 12mm mild steel plate of size 0.30 x 0.15m 2Nos with required holes. Conveying and leading the top beam arrangements to the work site. Fixing the top beam arrangements at the top of the vent in correct position including dismantling the existing eroded top beam, conveying and stacking and the section stores. The top beam should be painted with two coats of AC black paint over one coat of Red Oxide primer. The Rate including cost of materials, labours, charges for all fabricating and hoisting equipments, cost of petty civil works conveyance charges for labours and materials and warranty for 5 years etc.., complete. |
| 15 | Supplying and fixing of Head Set Assembly Light duty with hexagonal nut (Approximate 50 Kg) made up of cast iron including moulding, machining and the hexagonal nut threaded to suit the Screw Rod provided with thrust bearings for smooth operation. Conveying and leading the head set assembly to the work site. Fixing the head set assembly to the top beam by using required rust free bolts and nuts in proper alignment including dismantling the existing damaged Head set assembly supplied with operating key and the both should be painted with two coats of AC black paint over one coat of red oxide primer. The rate including cost of materials, labours, charges for wooden pattern, moulding and charges for labours and materials and warranty for 5 years etc., complete. |
| 16 | Fabricating, supplying and fixing of 50mm dia Screw Rod made up of Mild Steel duly machined and fully threaded to suit the Head set Assembly and provided with required holes. Conveying and leading the screw rod to the worksite. Fixing the screw rod to the shutter gusset plate with required bolt and nut in proper alignment to the head set including dismantling the existing damaged screw rod, conveying and stacking at section store. The Screw rod should be painted with two coats of AC black paint over one coat of red oxide primer. The rate including cost of materials, labours, charges for all fabricating and hoisting equipments, conveyance charges for labours and materials and warranty for 5 years etc., complete. |
| 17 | Supplying,hoisting,laying,jointing and fixing in position of RCC hume pipes of NP3 class of 900mm dia with suitable collars including labour and jointing materials etc, complete complying with standard specification and as directed by the Engineer in charge of work. |
| 18 | Providing and placing in position of Reinforced cement concrete of grade M25 using hard well graded coarse aggregates of maximum nominal size of 20mm weigh batching the incredients and mixing in approved mixers/batching plant (to produce concrete of the specified characteristic strength of 20 N/sqmm at 28 days) including dewatering the placement site, by bailing/pumping and by diverting wherever necessary, laying the concrete in layers of not exceeding 15cm thick and in bays, vibrating,compacting and finishing the surface to the profile with all leads and lifts, water curing to attain and strength as specified in the drawing for various depth and height below and above ground level etc., complete complying with the standard specification and as directed by the Engineer in charge of work |
| 19 | Supplying fabricating and placing in position of Ribbed Tor Steel bars of Various diameter for all reinforced cement concrete works including cost of rods, binding wire, labour charges for cutting the rods to the required length, bending, tying and fixing in position complete for various height and above ground level etc complete and complying with the standard specification and as directed by the Engineer in charge. |
| 20 | GST(18%) Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Sep 23, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedOct 08, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 13 daysOct 09, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 14 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender