Tender For Special Rep To Puf Shelter No. 633 (Tb/Bb) And Special Repair Of Toilet And Bathroom Block (Puf Sh No 440, 441 & 442) At Pms Under Ge Panagarh
Tender Value
47.50 Lakhs
Estimated cost
Bid Submission
14 Oct 2026
10 days left
EMD
95100
Bank guarantee accepted
Document Fee
500
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Purba Bardhaman → West Bengal
EMD Exemption
Not Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for Special Rep To Puf Shelter No. 633 (Tb/Bb) And Special Repair Of Toilet And Bathroom Block (Puf Sh No 440, 441 & 442) At Pms Under Ge Panagarh
BOQ
| Sl. No. | Item Description |
| 1 | Taking down cement plaster of any description from brick wall surfaces etc including racking out joints and hacking for key, scrubbing down with water etc complete all as specified and directed |
| 2 | M&L Rendering 15 mm thick cement plaster in CM 1:6 on brick/concrete work surfaces finished even and smooth (without using extra lime or cement) complete all as specified and directed. |
| 3 | M&L for Rendering 15 mm thick cement plaster in CM 1:4 on fair faces of brick/concrete surfaces finished fair and even, mixed wth water proofing compound admixture (if directed) as per manufacturer's instruction, complete all as specified and directed.Note :- WPC will measuered and paid separatly under relevant item of schedule. |
| 4 | Supply only liquid water proofing compound complete all as specified and directed. |
| 5 | Demolation of RCC of any description and in any position not otherwise specifically provided for including (renforcement cut as per required to facilitate demolition) complete all as specified and directed. |
| 6 | M & L for reinforced cement concrete (Nominal Mix) M-25 (20mm graded stone aggregate) foundations, including rafts, footings, foundation beams, plinth beams; bases for columns, etc. and mass concrete etc complete all as directed. |
| 7 | M & L for TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with the including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed. |
| 8 | Demolition of cement concrete in ground floor & paving n. exc 15 cm thick (below or above GL) unreinforced complete all as specified and directed. |
| 9 | M & L 75 mm thick cement concrete type C2, for PCC (1:3:6) using 40 mm graded aggregate as in sub base and pavings etc finishing cement concrete surface rough complete all as specified and as directed. |
| 10 | M & L 75 mm thick cement concrete type D2, for PCC (1:4:8) using 40 mm graded aggregate as in sub base and pavings etc finishing cement concrete surface rough complete all as specified and as directed. |
| 11 | M&L for 75 mm thick cement concrete M10 (Nominal Mix) with 40mm graded crushed aggregate finished even and fair laid to a slope of 1 in 12, laid in alternate bays, each bay not exceeding 3 m length with joint filled with bituminous mastic filling comprising a mixture of 1 part of heated Industrial bitumen 85/25 grade and two parts of heated sand as in plinth protection complete all as specified |
| 12 | M&L forming construction joint 30mm deep X 10mm wide with sealing compound grade A complete all as spd and directed. |
| 13 | Dismantling of floor hearth or wall tiling including cement mortar bedding but not backing and removing serviceable tiles to store yard and rubbish off the primises as directed |
| 14 | M&L for 25 mm thick PCC 1:2:4 type B-0 (Using 12.5mm graded crushed stone aggregate) as in floor, finished the surfaces fair & even to receive floor finishes, complete all as specified and directed. |
| 15 | M&L Non Skid coloured ceramic tiles 10 mm thick (Square/rectangular) area of each tile exceeding 0.42 sqm but not exceeding 1.00 sqm in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cemeent to match and including over screed bed or bedding layer of mortar 15 mm thick laying floor finished in CM 1:6 complete all as specified and directed. |
| 16 | M&L for Glazed ceramic tiles in vertical surface 350x 250x 7 mm thick set and jointed in neat cement slurry over back coat of layer of 10 mm thick with cement mortar 1:4 and pointed in white or colour cement to match the colour of tiles complete all as speciified and directed. |
| 17 | M&L Non Skid coloured ceramic tiles 7 to8 mm thick (Square/rectangular) area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm on vertical surface such as skirtings etc. set and jointed in cement slurry over 10 mm thick rendering in CM 1:3 complete all as specified and directed.complete all as spd and as directed. |
| 18 | M&L for old size brickwork with flyash bricks, straight or curved on plan exc 6m mean radius, half bricks thick built in CM (1:4) for edging of path complete all as specified and directed. |
| 19 | M&L for old size brick work with fly ash bricks straight or curved on plan exc 6 m mean radius build in CM 1:6 all as specified as directed. |
| 20 | S & F in repairs vitreous china squatting pan, 'Orissa\\" pattern, size 580 mm X 440 mm white with ‘P’ or ‘S” trap, front or back inlet and integral foot rests, any pattern and including fixing , connector to flush pipe, lime concrete bedding and making connections to flush pipe, connector to branch pipe and anti syphonage pipes etc. including sealing the joints and making leak proof using sealant complete all as specified and as directed by Engineer-in-Charge. |
| 21 | S & F in repairs vitreous china wash down water closet (pedestal pattern), white including thermoplastic seats and covers of grade 2 type, flat with hinging device of bronze or brass with nickel chromium plating, fixing bolt, connector to flush pipe and making connections to flush pipe, connector to branch soil pipe and anti syphonage pipes etc. including sealing the joints and making leak proof using sealant complete all as specified and as directed by Engineer-in-Charge. |
| 22 | S&F in repair vitreous china Counter top wash hand basin (self rimming) leed NC0483 (size 600x400x185mm) clour brillaiant/ off white including brackets and prepolished granite slab of size 1000x600mm and cutting notch of required size as per the wash hand basin is to be fixed in it complete all as spd and as directed. |
| 23 | S&F in repair Vitreous China bowl urinal flat back, size of 465 x 355 x 265 mm white minimum), with grating and union for discharge pipe(back or corner wall type), complete including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and including 60mm long brass screws, pointing around urinal back in cement; fixing automatic flushing cistern with brackets, flush pipe, grating and Union for discharge pipe. |
| 24 | S&F Urinal Spreader of chromium plated any colour for fixing with 15 mm dia pipe complete all as spd and directed. |
| 25 | S&F in repairs 8MM rectangular shaped urinal partition with frosted glass size 450 mm x 900 mm terminating about 40 cm above floor level and fixed with stainless steel clamp on wall complete all as specified and directed. |
| 26 | S&F in repairs 10 litre capacity PVC low level flushing cistern with all accessories complete fixed with WC including syphone pipe, PVC flushing pipe of size complete (with brackets). Make- Hindware, Parryware, commander (Sim Line) incl flush pipe of plyethene of low or high density of PVC 32mm dia for low level cistern all as specified and directed. |
| 27 | S&F in repair 15mm bore fancy type stop valve/angle cock (multiple) , chromium plated cast copper alloy, screwed down , high pressure , with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed complete all as specified and directed. |
| 28 | S&F in repair PVC connection 15mm size PTMT nuts of length 600mm complete all as specified and directed. |
| 29 | S&F in repair 15mm bore long Swan neck pillar taps cast copper alloy,with capstan heads,chromium plated,screwed down, fancy type high pressure, with or without lettred 'HOT or COLD' with long screwed sunk and fly nuts complete all as specified and directed. |
| 30 | S&F as in repair bib taps cast copper alloy 15mm bore long neck body with fancy chromium plated screwed down, screwed for iron pipe or for brass ferrule complete all as specified and directed. |
| 31 | S&F in repairs CP grating square 150mm size complete all as specified and directed. |
| 32 | S&F in repairs CP grating square with waste hole 150mm size complete all as specified and directed. |
| 33 | S&F in repairs 600mmx450mm beveled edge mirror of selected quality glass, mounted on 6mm thick AC building board or commercial plywood and fixed to wooden plugs with chromium plated brass screws and cup washers complete all as specified and as directed. |
| 34 | S&F as in repair tubular towel rail brass chromium plated 20 mm dia `D' type 60 cm long between flanges complete all as spd and directed. |
| 35 | M&L for 18mm to 20mm thick granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, window-cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite including 20mm thick screed bed CM(1:6) including dismantling the existing complete all as spd and directed |
| 36 | Rounding to edges of stone slabs exposed edge, such as in steps, cooking platform and other similar situation complete all as spd and directed. |
| 37 | Taking down chowkats or frames exc 1.5 sqm but n. exc 4 sqm each with shutters (without taking off shutters from the frame) complete all as spd and directed. |
| 38 | Taking down of chowkats or frames not exc 1.5sqm each with shutters (without taking off shutters from frames ) complete all as spd and directed. |
| 39 | Taking down shutters of any description exc 2 sqm each complete all as spd and directed. |
| 40 | S&F for factory made single extruded WPC (wood polymer composite) solid plain flush door shutter of 30mm size comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum frame density of 650 kg/cum, screw withdrawal strength of 1800N (face) and 900N (Edge), minimum compressive strength of 50 N/mm2, modulus of elasticity 850N/mm2 and resistance to spread of flame of class A category with property of being termite /borer proof, water/moisture proof and fire retardant and fixing with stainless steel butt hings of required size with necessary full body threaded star headed counter sunk S.S screws , all as per direction of Engineer-in -Charge. Note :- Stainless steel butt hinges and necessary SS Screws shall be paid separately) |
| 41 | S & F solid PVC door frame of size 50 x 47 mm made out of 5 mm plain colour PVC sheet reinforced with MS square tube complete all as specified and directed. |
| 42 | S&F Factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of MS tubes for top & bottom rails MS frame shall be convered with heat moulded plain colour PVC 'C' channel having a PVC sheet strip of 20 mm width stuck inside with solvant cement for stiles and plain colour PVC sheet top rail, lock rail and bottom rail on either side and as gap insert of top rail and bottom rail, paneling of plain colour PVC sheet to be fitted in the MS frame welded/sealed to the stiles and rails with suitabale PVC sheet beading, and jointed together with solvant cement, and S&F in the frame at side as per specification and drawing. |
| 43 | S&F for Powder coated aluminium (minimum thickness of powder coating 50 micron) work for doors, windows, ventilators and partitions (Fixed portions) with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS:1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasketetc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including Aluminium snap beading for glazing/ paneling, all complete as per architectural drawings and the directions of Engineer-in-Charge. |
| 44 | S&F for Providing and fixing Powder coated aluminium (minimum thickness of powder coating 50 micron) for shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber/neoprene gasket required (Fittings shall be paid for separately) with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS:1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing/paneling, C.P. brass/ stainless steel screws all complete as per architectural drawings and the directions of Engineer-in-Charge. |
| 45 | M&L for 4mm thick figured glass, pin head type and glazing with oil putty or with brass screws in square n.exc 0.50 sqm in each pan for bathrooms/toilets ventilators complete as directed. |
| 46 | M&L sheet glass 4.8 mm thick ordinary quality and glazing with oil putty and pin in square n. exc 0.50 sqm in each pan complete as directed. |
| 47 | S & F stainless steel wire cloth, 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples complete all as specified and directed. |
| 48 | Welding in repairs exc 2.5cm but n exc 5cm in length with thickness of metal to be welded exc. 20mm but n.exc 25mm for windows and ventilators complete all as specified and directed. |
| 49 | S&F in repair aluminium (extruded section body) door closer hydraulically regulated, designation No. 3, universal type, suitable for door shutters of 851 to 1000 mm in width and of weight between 61 to 80 kg and fixed complete all as spd and directed. |
| 50 | S & F stainless steel Butt hinges100mm long medium weight ,cold rolled complete as specified. |
| 51 | S&F 75mm long butt hinges, extruded alluminium alloy/stain less steel with galvanised mild steel hinge pin, anodised and fixed , type C-21 complete all as specified and directed. |
| 52 | S&F aluminium anodised 150 mm barrel tower bolts of extruded section complete all as specified and directed. |
| 53 | S&F aluminium anodised 75 mm barrel tower bolts of extruded section complete all as specified and directed. |
| 54 | S&F 150 mm long aluminium alloy handles,fabricated type, anodised complete all as specified and directed. |
| 55 | S&F 75 mm long aluminium alloy handles,fabricated type, anodised complete all as specified and directed. |
| 56 | S&F for 150mm long floor door stopper of aluminium alloy body and tongue, anodised, with hard drawn steel spring, fixed in floor complete all as specified and directed. |
| 57 | S&F 300 mm long aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy and fixed complete all as specified and dirceted. |
| 58 | Taking up or down steel water tubings and fittings etc complete and making good disturbed surfaces of walls/ceilings etc for 15 mm bore pipe complete including stacking aside for reuse and removal of unserviceable items from site complete. |
| 59 | Taking up or down steel water tubings and fittings etc complete and making good disturbed surfaces of walls/ceilings etc for 20 mm bore pipe complete including stacking aside for reuse and removal of unserviceable items from site complete. |
| 60 | S&F 20 mm outer dia medium grade CPVC, SDR 11 & plain CPVC SDR 11 with all fittings (brass inside the fittings) and fixed complete to walls and ceiling or laid in floors complete all as specified and directed. |
| 61 | S&F 25 mm outer dia medium grade CPVC, SDR 11 & plain CPVC SDR 11 with all fittings (brass inside the fittings) and fixed complete to walls and ceiling or laid in floors complete all as specified and directed. |
| 62 | S&F PVC SWR pipes, type B 110 mm bore single socketed in any length with rubber ring joints laid in trenches or in floors all as specified and directed. |
| 63 | S&F for PVC (SWR) pipe type B double socketed in any length with rubber ring joints fixed to walls of 110mm dia complete all as specified and directed. |
| 64 | S&F PVC SWR pipes, type B 75 mm bore single socketed in any length with rubber ring joints fixed to walls complete all as specified and directed. |
| 65 | S&F for PVC SWR bends of 110 mm bore complete all as spd and directed. |
| 66 | S&F for PVC SWR bends of 75 mm bore complete all as spd and directed. |
| 67 | S&F PVC (SWR) junction single (single T) equal or unequal provided with access door of 110 mm dia complete all as spd and directed. |
| 68 | Supply and fix PVC SWR Nahani/ Floor trap, multi inlet connection, plain with grating including jointing with solvent cement, dia of outlet 75 mm, water seal minimum 50 mm, complete all as specified and directed by Engineer in charge. |
| 69 | S&F for PVC (SWR) vent cowl 110 mm bore complete all as specified and directed. |
| 70 | Supply and fix in repair for Gun metal gate valve,20 mm bore, cast copper alloy screwed down, high pressure with crutch or butterfly handle, screwed both ends for iron pipe or for unions all as specified and as directed. |
| 71 | M&L for preparation of new steel surfaces and applying two coats of synthetic enamel paint over a coat of red oxide primer of any description not otherwise described over 10cm width or girth complete all as spd and directed. |
| 72 | M&L preparation of old surfaces of steel PUF panell of any description over 10cm width or girth, not otherwise described and applying two coat of synthetic enamel paint through Gun spray complete all as spd and directed. |
| 73 | M&L for writing letters or figures (block, Roman, Italic or indian) n exc 30 cm complete all as spd and as directed. |
| 74 | Dismantling wrought iron or mild steel work of any description not otherwiseprovided for complete all as spd and directed. |
| 75 | SS & F for Hand rails, half round or other steel section or core for wooden hand-rail straight portion, drilled and countersunk for balusters running bars, for doors, balusters, nosing to steps including embeding in concrete and screwing etc. wind ties for roof including securing bolts complete all as spd and directed. |
| 76 | S&F Joist channel angle of tee section fixed independently without connecting plate as Fe 410 W (Gde-E-250 quality A complete all as spd and directed. |
| 77 | Dismaltaling of plain or corrugated steel sheeting , any gauge, thickness, including nainital or similar pattern roof coverings complete all as specified and directed. |
| 78 | M & L for pre-painted hot-dip aluminium-zinc alloy metallic coated of any profile steel sheet corresponding to IS 15965:2012 of durability class 3, atmospheric classification category 3, coating class AZ150, 0.50 mm thick, of an approved colour and having yield strength of 550 MPa as in roof covering fixed with self tapping screws as specified up to anyheight including all necessary scaffolding and safety measures complete all as specified and directed. |
| 79 | All as per BOQ Srl Item No 78.00 here-in-before but except sheets Note: Serviceble sheets shall be reused ater proper cleaning. |
| 80 | M & L for pre-painted hot-dip aluminium-zinc alloy metallic coated plain steel sheet as per IS 15965:2012 of durability class 3, atmospheric classification category 3, coating class AZ150, 0.50 mm thick, of an approved colour and having yield strength of 550 MPa as in ridge/ valley/ gutter fixed with self tapping screws as specified any height Mtr height including all necessary scaffolding and safety measures complete all as specified and directed |
| 81 | M&L for under/over deck leaking arresters to PUF/steel sheet roofs by using 5mm thick bituminous Sheet (exc 20sqcm and not exc 40sqcm of each piece) including filling of silicon selant metal adhesive materials in holes, MS screws, washers etc where required at leakges of roof sheets complete all as specified and directed. |
| 82 | Demolition for brickwork or stone/boulder masonry, build in cement mortar including all quoins, arches, facings, dressed stonework and removal or rubbish off the site complete all as specified and directed. |
| 83 | M&L for brickwork with fly ash old size bricks, straight or curved on plan exc 6m mean radius for manholes/septic tank/soak well etc built in CM (1:4) complete all as specified and directed |
| 84 | M&L for RCC precast cement concrete type B-1, 1:2:4 (using 20 mm graded stone aggregate)as in cover slab for manholes and similar article with plain face set in CM (1:4) complete all as specified and directed (Note: Reinforcement will be measured and paid separately) |
| 85 | M&L for rendering 15mm thick cement mortar (1:4 ) on inside and outside brick wall of man hole/ septic tank/ concrete surfaces even and smooth with using extra cement complete all as specified and directed |
| 86 | M&L for PCC 1:3:6, type C1(using 40 mm graded stone aggregate) as in foundation filling and mass concrete complete all as specified and directed. |
| 87 | M& L for PCC type D2 1:4:8 using 40 mm graded aggregate in foundations, fillings and mass concrete. |
| 88 | M & L for Mild steel TMT bars 6mm to 8mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips. |
| 89 | Demolition and breaking up 150mm dia drain pipes (Salt glazed ware, AC or Reinforced concrete) set in cement mortar complete all as spd and directed. |
| 90 | Material and labour for cement concrete bed to drain pipe for 150mm bore of pipe including forming cradles in Cement concrete 1:3:6 Type C2 complete all as specifiedand and as directed. |
| 91 | Supplying and laying of PVC underground drainage sewer system pipe bearing 160 mm dia SN 4 including jointing with couplar, bend tee as per site requirement complete laid in trenches or floors complete all as specified and directed. |
| 92 | M&L for RCC 1:1.5:3 type A1 (20 mm graded crushed stone aggregate) nominal mix as in slab supported on walls,beam and colunm in floors,roof landings,balconies, canopies, deck slabs and in shelves all as spd and directed. |
| 93 | M&LProviding and laying at or near ground level factory made kerb stone of M-25 grade cement concrete in position to the required line, level and curvature, jointed with cement mortar 1:3 (1 cement: 3 coarse sand), including making joints with or without grooves (thickness of joints except at sharp curveshall not to more than 5 mm), including making drainage opening whereverrequired complete all as specified as directed. |
| 94 | M&L for 50mm thick sand filling under floors or in foundations including watering and consolidation complete all as spd and as directed. |
| 95 | Material and labour for machine pressed pre-polished precast concrete interlocking paver coloured block with grey cement and pigment any shape and size confirming to IS 15658-2006 of 60 mm thickness, M-35 Grade complete all as spd and as directed. |
| 96 | Taking down carefully aluminium/Copper conductor point wiring (light , fan, socket or powr) complete including fittings such as switches, ceiling rose, pendents, regulators sockets etc and removing (except those to be reused shall be kept in safe custody at the site) and making good disturbed surfaces of walls, floors etc tomatch with the existing completeall as specified and directed. Please Enable Macros to View BoQ information |
| 97 | Taking down carefully aluminium/Copper conductor point wiring (light , fan, socket or powr) complete including fittings such as switches, ceiling rose, pendents, regulators sockets etc and removing (except those to be reused shall be kept in safe custody at the site) and making good disturbed surfaces of walls, floors etc tomatch with the existing completeall as specified and directed. Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Sep 24, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedOct 14, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 10 daysOct 15, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 11 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender