Tender For Special Repairs To Existing Hard Standing For Bmp Yard Area In Front Of Bldg No P-502, P-266, P-500, P-431, P503, P504, P-449 & P-265 At Brichgunj Mil Stn, Sri Vijaya Puram
Tender Value
86.99 Lakhs
Estimated cost
Bid Submission
21 Oct 2026
27 days left
EMD
1.55 Lakhs
Bank guarantee accepted
Document Fee
1000
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
South Andamans → Andaman And Nicobar Islands
EMD Exemption
Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for Special Repairs To Existing Hard Standing For Bmp Yard Area In Front Of Bldg No P-502, P-266, P-500, P-431, P503, P504, P-449 & P-265 At Brichgunj Mil Stn, Sri Vijaya Puram
BOQ
| Sl. No. | Item Description |
| 1 | Demolition of cement concrete unreinforced in ground floors and pavings n. exc. 15 cm thickness (below or above ground level) complete all as specified and directed by Engineer-in-charge. |
| 2 | M&L for providing PCC 1:2:4 type B-0 using 12.5mm graded stone aggregate as in mass concrete using river sand obtained from main land only using non metalic floor hardner complete all as specified and directed by Engineer-in-charge.Note : Non metalic floor hardner shall be measured and paid separately. |
| 3 | Supply only non metalic floor hardner. |
| 4 | M&L for Tie bars of Grade Fe-500D of 10 mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips or welded complete all as specified and directed by Engineer-in-charge. |
| 5 | Use and waste of Formworks to sides of concrete foundations,piles caps, footings, base of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams and similar works,vertical or to batter for rough finished surfaces complete all as specified and directed by Engineer-in-charge. |
| 6 | M&L for finishing surface of concrete pavements by brooming complete all as specified and directed by Engineer-in-charge. |
| 7 | M&L for Forming expansion joints,20mm thick filled with pre formed bituminous filler and top 30mm primed with sealing compound , Grade 'B' for 150 mm thick flooring complete all as specified and directed by Engineer-in-charge. |
| 8 | M& L for Forming Contraction (Dummy) joints 65mm deep x 10mm wide filled with sealing compound Grade 'B' for 150 mm thick flooring complete all as specified and directed by Engineer-in-charge. |
| 9 | M& L for providing Construction joint 30 mm deep x 10 mm wide filled with sealing compound Grade 'B' complete all as specified and directed by Engineer-in-charge. |
| 10 | Demolition of PCC Block walling built in CM 1:6 complete all as specified and directed by Engineer-in-charge. |
| 11 | M&L precast cement concrete block masonry with PCC solid blocks in 1:3:6 type C1 using 20mm graded stone aggregates, exc. 10cm in width and set in CM 1:4 complete all as specified and directed by Engineer-in-charge. |
| 12 | M&L Rendering 10mm thick on other than fair faces of Brick / Concrete Surfaces on walls in CM (1:6), finished even & smooth without using extra cement complete all as specified and directed by Engineer-in-charge. |
| 13 | M&L for precast cover slab with 1:2:4 type B1 using 20mm graded stone aggregate incl cost of use and waste of clean sawn wooden form work but excl cost of reinforcement all as specified incl removal of existing unserviceable cover slab complete all as specified and directed by Engineer-in-charge. |
| 14 | M&L for Mild steel bars 8 mm dia TMT bars, cut to length, bent to shape required, including cranking, bending spirally for hooping for man hole covers, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips for man hole cover complete all as specified and directed by Engineer-in-charge. |
| 15 | Extra for forming fair finished drain or channel 30cm inner girth in cement complete all as specified and directed by Engineer-in-charge. |
| 16 | Add or deduct for each 25 mm girth or part thereof over or under 30 cm |
| 17 | M & L for preparing Old steel/ Iron surfaces of any description exc 10cm Width or Girth and applying One coat of synthetic enamel paint complete all as specified and directed by Engineer-in-charge. Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Sep 23, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedOct 21, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 27 daysOct 23, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 29 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender