Tender For Repair/ Maintenance Of Lt Cables, Lt Panels, Poles Earthings, Distribution Pipe Lines, Pump Set, Motors, Lt Panels, Starters, Water Meers & Connected Works At Mes INSTALLATION Solan And Rapair/ Replacement Of Internal Wiring, Geysers, Exha
Tender Value
50 Lakhs
Estimated cost
Bid Submission
14 Oct 2026
19 days left
EMD
1 Lakhs
Bank guarantee accepted
Document Fee
500
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Solan → Himachal Pradesh
EMD Exemption
Not Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for Repair/ Maintenance Of Lt Cables, Lt Panels, Poles Earthings, Distribution Pipe Lines, Pump Set, Motors, Lt Panels, Starters, Water Meers & Connected Works At Mes INSTALLATION Solan And Rapair/ Replacement Of Internal Wiring, Geysers, Exhaust Fan & Submian Wiring, Led Fitting And Fixtures & Connected Services For Otm & Md Accn At Solan Under Ge Kasauli.
BOQ
| Sl. No. | Item Description |
| 1 | Schedule 'A' Section - I |
| 2 | Dismantling of old UNSV ACSR or AAC conductors, any type and size from the poles complete, all as specified and directed by Engr-in-Charge. |
| 3 | Supply and fixing new ACSR conductor including stringing on LT poles complete including aluminium binding wires, jumpering, bindings at insulators etc, complete, all as specified and directed by Engr-in-Charge. |
| 4 | Dismantling stay assembly complete.(demolition of concrete, etc. and excavation measured separately), complete all as specified and directed by Engr-in-Charge. |
| 5 | Supply and fixing Stay assembly complete with accessories as shown in electrical plate No-1 (loop type insulator, stay clamps, excavation and concrete measured separately) with stay rod 16mm dia, MS plate 6mm thick size 230x230mm, complete, all as specified and directed by Engr-in-Charge. |
| 6 | Dismantling of cross arms fixed on Steel tubular poles carefully including separating and getting aside, serviceable cross arms for re-use in the work and removing unserviceable cross arms from site complete all as specified directed. |
| 7 | Dismantling insulators any type, any size complete all as specified and directed by Engr-in-Charge. |
| 8 | Supplying & fixing in replacement of pin insulator porcelain vitreous, white, brown & green incl. One galvanised mild steel spindle, two galvanised iron washers and one galvanised iron nut, 100mm height 65mm dia for 1100 volts grade, complete, all as specified and directed. |
| 9 | Supplying & fixing in replacement of shackle type porcelain, vitreous , white, brown or green insulator including galvanised mild steel straps washers insulator bolts, washer and nuts of size 100 mm height, 115mm dia for working pressure 1100 volts, complete, all as specified and directed. |
| 10 | Supply and fixing Loop type insulator, vitreous porcelain white , brown, green small size with overall dimensions 65mm x 90mm clearance of hole 16mm, complete, all as specified and directed. |
| 11 | Taking down street/security/Gate light/ Solar light fittings LED light fittings of any capacity or type from pole/wall after disconnection and connecting wires, carrying out to store yard for necessary repair/replacement of spares and fittings etc.,complete all as specified and directed. |
| 12 | Supply and fixing in replacement of LED post top lantern LED type 20 watt 230 watt volts AC outdoor type waterproof with decorative post top for 360 degree indirect light IP 65 protection with impact and corrosion resistant complete with driver and lamp complete all as specified and directed by Engr-in-Charge. |
| 13 | Supply and fixing in replacement of Supply and fixing LED street light fitting 60 Watt 230 V AC outdoor type with high pressure die cast aluminum hosing and heat resistant complete with driver, lamp bracket with impact and corrosion resistant including thermal management in multiple optics complete with IP 65/66 protection complete all as specified and directed by Engr-in-Charge. |
| 14 | Supply and fixing in replacement of Supply and fixing LED street light fitting 35 Watt 230 V AC outdoor type with high pressure die cast aluminum hosing and heat resistant complete with driver, lamp bracket with impact and corrosion resistant including thermal management in multiple optics complete with IP 65/66 protection complete all as specified and directed by Engr-in-Charge. |
| 15 | Supply and fixing inreplacement of LED flood light fitting 120 Watt 230 V AC outdoor type with high pressure die cast aluminum hosing and heat resistant complete with driver, lamp bracket with impact and corrosion resistant including thermal management in multiple optics complete with IP 65/66 protection complete all as specified and directed by Engr-in-Charge. |
| 16 | Supplying & fixing in replacement of street light fitting GI bracket made out of 40mm bore GI pipe, light grade, tubing bend to shape, 1.2 metre long, fixed to pole/wall complete, all as specified and directed. |
| 17 | Supplying & fixing in replacement of clamps made out of 40x6 mm bending to shape, drilling holes for bolts suitable for fixing GI pipe bracket to steel pole, made in two halves, including nuts, bolts, washers and painting with two coats of aluminium paint over a coat of red oxide primer, complete, all as specified and directed. |
| 18 | Supply and fixing Steel water tubing, light grade, galvanised (ISI marked), 50 mm bore with all fittings, laid in trenches/ under roads or fixed to poles for passing cables for protection of cables, complete, all as specified and directed. |
| 19 | Supply and fixing Steel water tubing, light grade, galvanised (ISI marked), 40 mm bore with all fittings, laid in trenches/ under roads or fixed to poles for passing cables for protection of cables, complete, all as specified and directed. |
| 20 | Supply and fixing Steel water tubing, light grade, galvanised (ISI marked), 25 mm bore with all fittings, laid in trenches/ under roads or fixed to poles for passing cables for protection of cables, complete, all as specified and directed. |
| 21 | Supply and fixing Steel water tubing, light grade, galvanised (ISI marked), 20 mm bore with all fittings, laid in trenches/ under roads or fixed to poles for passing cables for protection of cables, complete, all as specified and directed. |
| 22 | Taking down carefully under ground cable of any size and making good to disturbed surface as per existing complete all as specified and directed. |
| 23 | Supply, laying, jointing and testing of XLPE insulated, armoured, heavy duty LT cable 1100 Volts grade with aluminium conductor laid in trenches, on poles, through pipes, fixed to walls etc cross sectional area 25 Sqmm 3.5 core, complete, all as specified and directed. |
| 24 | Supply, laying, jointing and testing of XLPE insulated, armoured, heavy duty LT cable 1100 Volts grade with aluminium conductor laid in trenches, on poles, through pipes, fixed to walls etc cross sectional area 16 Sqmm 4 core, complete, all as specified and directed. |
| 25 | Supply, laying, jointing and testing of XLPE insulated, armoured, heavy duty LT cable 1100 Volts grade with aluminium conductor laid in trenches, on poles, through pipes, fixed to walls etc cross sectional area 16 Sqmm 2 core, complete, all as specified and directed. |
| 26 | Supply, laying, jointing and testing of XLPE insulated, armoured, heavy duty LT cable 1100 Volts grade with aluminium conductor laid in trenches, on poles, through pipes, fixed to walls etc cross sectional area 10 Sqmm 2 core, complete, all as specified and directed. |
| 27 | Supply, laying, jointing and testing of XLPE insulated, armoured, heavy duty LT cable 1100 Volts grade with aluminium conductor laid in trenches, on poles, through pipes, fixed to walls etc cross sectional area 50 Sqmm 3.5 core, complete, all as specified and directed. |
| 28 | Supply, laying, jointing and testing of XLPE insulated, armoured, heavy duty LT cable 1100 Volts grade with aluminium conductor laid in trenches, on poles, through pipes, fixed to walls etc cross sectional area 95 Sqmm 3.5core, complete, all as specified and directed. |
| 29 | Supply, laying, jointing and testing of XLPE insulated, armoured, heavy duty LT cable 1100 Volts grade with aluminium conductor laid in trenches, on poles, through pipes, fixed to walls etc cross sectional area 70 Sqmm 3.5core, complete, all as specified and directed. |
| 30 | Supply, laying, jointing and testing of XLPE insulated, armoured, heavy duty LT cable 1100 Volts grade with aluminium conductor laid in trenches, on poles, through pipes, fixed to walls etc cross sectional area 120 Sqmm 3.5core, complete, all as specified and directed. |
| 31 | Supply, laying, jointing and testing of XLPE insulated, armoured, heavy duty LT cable 1100 Volts grade with aluminium conductor laid in trenches, on poles, through pipes, fixed to walls etc cross sectional area 630 Sqmm 3.5core, complete, all as specified and directed. |
| 32 | Supply, laying, jointing and testing of XLPE insulated, armoured, heavy duty LT cable 1100 Volts grade with aluminium conductor laid in trenches, on poles, through pipes, fixed to walls etc cross sectional area 240 Sqmm 3.5core, complete, all as specified and directed. |
| 33 | Streching of loose ACSR conductor including jumpering, binding,etc all as required in LT OH line, complete, all as directed. Note:- Disconnecting the existing security light or cable connection before stringing and reconnecting after stringing is included in the rates quoted. |
| 34 | Supplying & fixing in replacement of connection/Junction box made out of 1.6mm thick MS sheet front openable, weather & vermin proof including painting two coats of synthetic enamel paint over a coat of red primer. Connection box shall be suitable for housing & including aluminium bus bar 25 Amps cap - 2 Nos, MCB SP 6 Amps- 01 No and having provision of cable hole in bottom for two to three cables of size 16 Sqmm 4 core armoured cable connection box shall be fitted on street light pole and fixing arrangements i.e. MS clamps etc deemed to be provided by the contractor, size of box - 200 x 150 x 100mm, complete, all as directed. |
| 35 | Supplying & fixing in replacement of double walled corrugated HDPE duct pipe of 110 mm outer dia confirming to IS-14930 (Part-II) of approved colour with fittinggs for cable protection complete all as specified and direcetd. |
| 36 | Supplying & fixing in replacement of double walled corrugated HDPE duct pipe of 63 mm outer dia confirming to IS-14930 (Part-II) of approved colour with fittinggs for cable protection complete all as specified and direcetd. |
| 37 | Supplying and fixing 1100 volts grade heavy duty cable 4 sqmm 2 core PVC insulated aluminium conductor, served with inner sheathing of PVC tape and overall PVC sheathed in service connections one twin core cable flat or circular complete all as specified and directed by Engr - in - Charge. |
| 38 | Dismantling steel poles/struts, any size complete all as specified and directed by Engineer-in-Charge. |
| 39 | Supply and fixing in replacement of Steel tubular swaged poles complete with cast iron base plate, final, taper plug, bolts, nuts and screws as specified type 410 SP-31 9.0 mtr long duly painted with two coats of aluminium paint over a coat of red oxide primer complete, all as specified and directed.Note- Excavation, earth work and PCC shall be measured and paid separately. |
| 40 | Material and labour for Painting of steel tubular pole 9.0 metre long, by applying two coat of aluminium paint after scraping / brushing and cleaning the rust on pole and cross arms. Aluminium painting will be done on pole above 1.5 metre height from ground level and balance 1.5 mtr from ground level will be painted by alternate layer of black and white enameled paint (30 Cms each). Pole Nos will be written on pole by black paint in yellow circle of 150mm dia, complete, all as specified and directed. Note:- Only one coat will be applied at one time and payment at 50% of coated rate to be applied at the first time of first coat. Second coat is to be done more than 15 days after first coat. |
| 41 | Material and labour for painting of LT/Distribution Panel Board after cleaning and surface preparation, applying one coat red oxide primer and two coats synthetic enamel paint of approved shade including writing of panel name, feeder details, panel number, danger sign and identification markings complete, all as specified and directed by Engineer-in-Charge. |
| 42 | Supplying and laying synthetic Rubber insulated mats 2 mm thick for voltage upto 3.3 kv for electrical purpose as per IS 15652-2006, (superseding IS 5424) suitable for electrical shock safety of sizes 2m x 1m., complete all as specified and directed by Engr-in-Charge. |
| 43 | Supply and fix in replacement of Sheet metal enclosure bus bar including fiiting on wall/pole including and making the connection with MCCB 4 Pole 100 Amps 16 KA, 415 volts , 50 Hz ,thimble/lugs, aslo including all nuts bolts required for fixing all as specified and directed by Engineer - in - Charge. |
| 44 | Supply and fix in replacement of MCCB 4 pole 400 Amps 36 KA capacity AC 415 v complete all as specified and directed. |
| 45 | Supply and fix in replacement of MCCB 4 pole 250 Amps 36 KA capacity AC 415 v complete all as specified and directed. |
| 46 | Supply and fix in replacement of MCCB 4 pole 500 Amps 36 KA capacity AC 415 v complete all as specified and directed. |
| 47 | Supply and fix in replacement of MCCB 4 pole 160 Amps 36 KA capacity AC 415 v complete all as specified and directed. |
| 48 | Supply and fix in replacement of MCCB 4 pole 100 Amps 16 KA capacity AC 415 v complete all as specified and directed. |
| 49 | Material and labour for L.T. lightning arresters for outdoor use, non-liner resistor type, horn gap and choking coil, maximum working pressure 1100 volts including dismantling and taking down old arrestors complete all as directed |
| 50 | Material and labour for PVC spacer suitable for 5 wire LTOH line including taking down of old one. complete all as specified and directed by Engr-in-Charge. |
| 51 | Material and labour for PVC spacer suitable for 6 wire LTOH line including taking down of old one. complete all as specified and directed by Engr-in-Charge. |
| 52 | Pruning of tree branches and making clear LT line to the minimum distace of 1.8 mtrs all arround complete all as specified and directed by Engr-in-Charge. |
| 53 | For 3/4 conductors |
| 54 | For 5/6 conductors |
| 55 | Supply and fix in replacement of digital time switches astro type (Having longitude and latitude of Indian cities in memory) 250 V single phase of 20 Amp rating with contactor fitted inside steel enclosure. complete all as specified. |
| 56 | Taking out existing earthings and Material and labour for replacement of 'Earthing complete with and including galvanised steel earth plate electrode 60cm x 60cm x 6 mm thick surrounded by mixture of charcoal and salt in alternate layers , buried directly in ground vertically in a pit of depth not less than 2.25 meter deep below ground level with top as of the plate at a depth of not less than 1.5 mtrs below normal ground level connected to equipment by using GI strips of size 32x6 mm as earthing lead by means of bolts ,nuts, check nuts and washers of galvanised iron or steel earth wire protected by galvanised steel pipe 40 mm bore (light grade) and 20mm bore \\"Light' grade GI watering pipe connected to main switch or main control board or GOD or lightening arrester all as shown in electrical plate No. 3 of SSR - 2009(Pt I) & including necessary excavation and earth work. The rate also include charcoal and salt in alternate layers, 20 mm bore GI pipe (Light grade ) for watering , protection pipe funnel, wire mesh , PCC 1:2:4 type B1 chamber in cement concrete ,50 mm thick precast RCC M-25 ( Design mix) cover duly reinforced with XPM (weight not less than 3 kg /sqm ) and CI frame etc , and including provision of test point , connecting to test point and testing on completion etc, complete all as specified. NOTE : The unit rate include earthing lead and protection pipe upto 7.5 metre from top of earth plate. |
| 57 | Supply & fixing Glavanised iron strip 32x6mm buried in ground complete all as specified and directed by Engr-in-Charge. |
| 58 | Dismantling old unsv and Supply and fixing of shock treatment chart as per E-in-C's pattern size 2 feet x 4 feet aluminium board with alluminium frame & glass with houging aggrements all as directed. |
| 59 | Supply and fix cable jointing kit for 1.1 KV grade cable for straight through joint complete with Jointing material heat/cold Shrink type and accessories suitable for 3 ½ / 4 core XLPE, armoured, Al conductor cable of size185 to 240 sqmm,Indoor/Outdoor type including taking down of old one. |
| 60 | Supply & fixing in repair Digital Amp meter with selector switch and CTs 0 to 500 Amps 96 x 96 mm, Class 1, AC. As per existing Make & Model. complete all as specified and directed by Engr-in-Charge. |
| 61 | Supply & fixing in repair Digital Volt meter with selector switch and 0 to 500 votls 96 x 96 mm, Class 1, AC. As per existing Make & Model. complete all as specified and directed by Engr-in-Charge. |
| 62 | Material and labour for Laying cement concrete for foundation fillings and mass conctere type D2 1:4:8 ( 40 mm graded aggregate ) complete all as specified and directed. |
| 63 | Material and labour for PCC 1:3:6 (40 mm graded aggregate) Type C2 for foundation of pole, stay incl frame work where reqd all as specefied and directed. |
| 64 | Material and labour for Laying cement concrete for copying of poles type B1, 1:2:4 (20 mm graded crused stone aggregate) ,smooth finishing without using extra cement complete all as specified and directed. |
| 65 | Supply, installation, testing and commissioning in replacement factory made bus bar chamber, outdoor type, weather proof having both side openable hinged door shutters with locking arrangement, size of chamber 90cm x 60cm x 50cm made of 3mm thick CRCA sheet, powder coated paint inside and outside, welded with 4 Nos angle iron legs of size 40 x 40 x 6mm, 60cm long duly painted with two coats of black enamelled paint over a coat of red oxide primer and errected in PCC 1:3:6, type C2 foundation at suitable depth and having the following accessories:-Incoming : MCCB 04 pole 100 Amp, 25 KA Outgoing : 04 Nos 600 Amp Aluminium bus bar incl 08 nos hole on each bus bar with nut and bolts. |
| 66 | Disconnecting the electrical connections of motor, water supply to the Pump and taking out pump after disconnecting both motor and pump mechanically 10 to 15 HP capacity (Make- Kirloskar / C&G ) capacity - 45 Cum at 35 metres head installed at Water Pump House and Back Solan and transporting the same to an authorized workshop for following repairs :- |
| 67 | Supply and fixing Shaft with keys made out of steel 410 grade for Srl Item No 63.00 complete all as specified and directed by Engr-in-Charge. |
| 68 | Shaft sleeve with nuts made out of stainless steel 410 grade for Srl Item No 63.00 complete all as specified and directed by Engr-in-Charge. |
| 69 | Set of pins and Gaskets made out of Mild Steel for Srl Item No 63.00 complete all as specified and directed by Engr-in-Charge. |
| 70 | Coupling set made out of Cast Iron including bolts, nuts, washers & rubber bushes for Srl Item No 63.00 complete all as specified and directed by Engr-in-Charge. |
| 71 | Gland box made out of Cast Iron including gland box studs with nuts and washers for Srl Item No 63.00 complete all as specified and directed by Engr-in-Charge. |
| 72 | Gland packing made out of Gr. Cotton for Srl Item No 63.00 complete all as specified and directed by Engr-in-Charge. |
| 73 | Impeller made out of cast Iron duly balanced by means of precision lathe machine for Srl Item No 63.00 complete all as specified and directed by Engr-in-Charge. |
| 74 | Driving End bearing for Srl Item No 63.00 complete all as specified and directed by Engr-in-Charge. |
| 75 | Non Driving End bearing for Srl Item No 63.00 complete all as specified and directed by Engr-in-Charge. |
| 76 | Material and labour for applying two coats painting of PUMP with super enamelled paint on steel with black colour applying two coats by spray method complete all as specified and directed. |
| 77 | Disconnecting the electrical and mechanical connections of motor, and taking out motor,15 HP capacity at Solan Pump House. Transporting the same to an authorized workshop for following repairs:-(a) Dismantling burnt AC 3 Phase, 50 Hz, motor, 15 HP taking out all coils and re-winding the motor complete with same gauge of wire and same nos of turns. Heating, Baking and varnishing the winding complete. Re-assembling the motor and fixing back in position all as directed by Engr-in-Charge and recommended by the manufacturer. |
| 78 | All as per item No 64.00 here-in-before but for, 10 HP capacity complete all as specified and directed by Engr-in-Charge. |
| 79 | Material and labour for applying two coats painting of Motor with super enamelled paint on steel with grey colour applying two coats by spray method complete all as specified and directed. |
| 80 | Supply / laid PVC insulated unsheathed multistranded HRFR 3 x single core ( R,Y,B) copper conductor 1100 volts grade of size 16 sqmm passing through existing PVC/ERW conduit from starter upto pump fixed with required size of copper lugs complete all as specified and directed by Engr-in-Charge.( Note- 3 single core wire of 16 sqmm ( colour coding RYB) will be measured as one length of 1 RM) |
| 81 | Supply and fixing in replacement of Water meter 100 mm nominal bore conforming to IS:2373-1981 having CI casing bronze body and SS/Alloy/Bronze gear having dial duly marked with litres or kilolitres in boldface, thread/flanged end type with provision of strainer out side the meter complete all as specified and as directed by Engr-in-Charge. |
| 82 | Supply and fixing in replacement of Foot Valve conforming to IS-4038 flanged ISI marked completed with nut, bolts, washers etc including taking out old existing u/s foot valve of 100 mm dia and directed by Engr-in-Charge. |
| 83 | Supply and fixing Push Button 22.5 mm with push knob flush type having 1 NO & 1 NC illuminated type for putting on / off the starter suitable as per site requirement and directed by Engr-in-Charge. |
| 84 | Supply and fixing LED indicating light surge and low voltage protected 220 / 240 Volts AC, Colour R/Y/G/A suitable as per site requirement and directed by Engr-in-Charge. |
| 85 | Supply and fixing electronic star delta Timer ( 1 to100 sec) DQR 415/240V, 110V : AC complete suitable as per site requirement and directed by Engr-in-Charge. |
| 86 | Supply and fixing in replacement Star delta starter for 10-15 HP motor pump 415 AC complete suitable as per site requirement and directed by Engr-in-Charge. |
| 87 | Supply & fixing in repairs Volt Meter Digital, 96 x 96 mm, 0-500 Volts, Class 1, AC. As per existing Make & Model. complete all as specified and directed by Engr-in-Charge. |
| 88 | Supply & fixing in repairs Amp Meter Digital, 96 x 96 mm, 0-100 Amps, Class 1, AC. As per existing Make & Model. complete all as specified and directed by Engr-in-Charge. |
| 89 | Supply & fixing in repairs die cast resin CT, copper wound Class 1, for digital Amp Meters. Ratio of CT- as per existing Make & Model, complete all as specified and directed by Engr-in-Charge. |
| 90 | Taking out old & unserviceable power contactor and Supply & fix power contactor for S/D starter 15 HP (BCH Make) 3 pole, 32 Amps for AC 3 rating 415 volts, 15 kW 50 Hz supply including control coil, 1NO+1NC, contact springs, spring retainers and arc runners complete all as specified and directed by Engr-in-Charge. |
| 91 | Taking out old & unserviceable power contactor and Supply & fix power contactor for S/D starter 10 HP ,3 pole,12 Amps for AC 3 rating 415 volts, 5.5 KW , 50 Hz supply including control coil, 1NO+1NC, contact springs, spring retainers and arc runners complete all as specified and directed by Engr-in-Charge. |
| 92 | Supply & fixing in repairs MCCB 4 Pole 63 amps rating 415 volts AC. As per existing Make & Model. complete all as specified and directed by Engr-in-Charge. |
| 93 | Supply & fixing in repairs MCCB 3 Pole 32 amps rating 415 volts AC. As per existing Make & Model. complete all as specified and directed by Engr-in-Charge. |
| 94 | Supply & fixing in repairs Selecter switch 3 ON & OFF As per existing Make & Model. complete all as specified and directed by Engr-in-Charge. |
| 95 | Taking out existing earthings andMaterial and labour for replacement of chemical earthing (Pipe in pipe technology) Two B class IS mild steel pipe, one inside the other, hot dip galvanised with 100 micron coating outside and about 300 micron coating inside filled with high conductive and corrosion Resistant Crystalline Mixture inside and Backfill compound around the outer electrode) outer electrode dia 72 to 80mm and inner electrode dia 35 to 40 mm both 10' long, incldg making earth pit of size 4' x 4' and 11' deep fill the entire pit with black cotton soil or normal soil, pour enough water so that pit is full with water, leave it for three days so that soil soaks up the water, the soil level has goes down, again top up the pit with soil & fill the water. After two or three days when the pit is sturdy and ready for earthing purpose, install the earthing electrode as per installation method as below:- (a) Mix backfill compound evenly with soil. (b) Remove plastic sleeve carefully from electrode. (c) Place naked electrode at centre of pit. (d) Start refilling empty space around electrode with backfill compound in layers. (e) Pour some water and poke the pit with a long wooden rod to allow trapped air to escape. (f) Gradually continue refilling process till electrode is buried in the pit up to the green patch painted on the top portion of electrode. (g) Ensure that pit is not watery (h) Pack electrode with compound nicely and tightly, so that it stands firmly in pit. (j) Pour a few buckets of water around pit. (k) Pour a few buckets of water around in the pit everday for 10-15 days for system to set. (l) Connect the earth electrode with equipments by 25mm x 3mm aluminium strip. (m) Earthing test point terminal block made of gun metal size 150x100x50 mm drilled and screwed including 4 Nos 8 mm dia 40 mm long hexagonal head bolts and washers duly fixed on walls with fasteners 4 Nos. Note : (a) Earth resistance shall not be more than 5 Ohm. (b) Aluminium strip for connections shall be measured and paid separately. |
| 96 | Taking out old unsv and Supplying, fixing and testing of cast steel Sluice valve PN1.6 as per IS-14846, body, dome, wedge-CI IS:210, rings-bronze IS:318, Spindal-SS IS:6603, Gland Paking greasy jute packing, fasteners-CS, Gasket- Natural rubber, nominal size DN-150 mm, both ends flanged in existing line, after removal of old unserviceable sluice valve without damaging to existing pipe line complete all as specified and directed by Engr-in-charge. Note : Suitable size flanges for existing pipe line, Joints and jointing materials shall be included under this item. |
| 97 | All as per serial item No. 83.00 here-in-before but nominal size DN-100 mm -ditto-. |
| 98 | All as per serial item No. 83.00 here-in-before but nominal size DN-80 mm -ditto-. |
| 99 | Supply and fixing Cast iron Non Return valve W/O by pass arangement , Swing type, of Size 100 mm bore, confirming to IS 5312, flanged ends with nuts bolts, washers complete including taking down of old one as directed by Engr-in-Charge . |
| 100 | Supply and fixing Cast iron Non Return valve W/O by pass arangement , Swing type, of Size 150 mm bore, confirming to IS 5312, flanged ends with nuts bolts, washers complete including taking down of old one as directed by Engr-in-Charge . |
| 101 | Supply and fix Cast Iron Air Release Valves with two air Outlets, conforming to IS 14845 of size 100 mm dia bore and fixing up in Cast Iron Water supply mains of size 100 mm dia as directed by Engr-in-Charge . |
| 102 | Supply and fix Cast Iron Air Release Valves with two air Outlets, conforming to IS 14845 of size 150 mm dia bore and fixing up in Cast Iron Water supply mains of size 150 mm dia as directed by Engr-in-Charge . |
| 103 | Construction of brick masonary pit of size 60 x 60 x 60cm internal size with MS sheet 3mm thick and angle iron frame of size 40x40x6mm duly painted with 2 coats of synthetic enamel paint over a coat of red oxide primer including locking arrangement, lifting handle and including excavation / earth work, PCC in foundation, brick work, plaster including demolition of existing pit complete all as specified and shown in drawing No. STD- 1258, sheet 1/1. (original date - 30.11.93 and revised date - 15.09.2000 ).Note : Drawing mentioned above has not been enclosed herewith, however the same can be seen in the office of GE Kasauli. |
| 104 | Construction of brick masonary pit of size 90 x 90 x 90 cm internal size with MS sheet 3mm thick and angle iron frame of size 40x40x6mm duly painted with 2 coats of synthetic enamel paint over a coat of red oxide primer including locking arrangement, lifting handle and including excavation / earth work, PCC in foundation, brick work, plaster including demolition of existing pit complete all as specified and shown in drawing No. STD- 1258, sheet 1/1 (original date - 30.11.93 and revised date - 15.09.2000 ).Note : Drawing mentioned above has not been enclosed herewith, however the same can be seen in the office of GE Kasauli. |
| 105 | Supply, fabricating and fixing, in replacement, of cross arms (any type) supports, bracing, stiffness, clamps, back plate, base frame structure etc made out of MS channel, angle iron, flat iron of any size including all machine works i.e. drilling of holes, welding, cutting, grinding etc as required, including painting with two coats of aluminium paint over a coat of red oxide paint and all fixing accessories i.e. nuts, bolts and washers etc, complete all as directed. |
| 106 | Supply & fixing or fabricated of Mild steel frame glow sign boards on flex sheet size 1550mm x 910mm duly indicating the name of installation and logo of MES with suitable redium stencil and necessary items for fixing on roof /wall grouting/ PCC work complete all as directed by Engr-in-Charge.Note : Background colour sky blue and matter or size of stencil as direction by Engr-in-Charge. |
| 107 | Supply and fixing in replacement of LED type indicator lamp of red/blue/green colour for phase indication in existing LT panel/ motor starter panel/ APFC panel, complete all as directed. |
| 108 | Supply and fixing in replacement of start push botton green in existing motor starter panel/ APFC panel, complete all as directed. |
| 109 | Supply and fixing in replacement of stop push botton red in existing motor starter panel/ APFC panel, complete all as directed. |
| 110 | Supply and fixing in replacement of single phase preventor (SPP) in existing motor starter panel/ APFC panel, complete all as directed. |
| 111 | Supply and fixing in replacement of Motor 'ON' indicating green light in existing motor starter panel, complete all as directed. |
| 112 | Supply and fixing in replacement of Motor 'Trip' indicating red light in existing motor starter panel, complete all as directed. |
| 113 | Construction of brick masonary pit of size 120 x 120 x 120 cm internal size with MS sheet 3 mm thick and angle iron frame of size 40x40x6mm duly painted with 2 coats of synthetic enamel paint over a coat of red oxide primer including locking arrangement, lifting handle and including excavation / earth work, PCC in foundation, brick work, plaster including demolition of existing pit complete all as specified and shown in drawing No. STD- 1258, sheet 1/1 (original date - 30.11.93 and revised date - 15.09.2000 ).Note : Drawing mentioned above has not been enclosed herewith, however the same can be seen in the office of GE Kasauli. |
| 114 | Supply of calcium hypo chloride, 65%-70% chlorine content, high strength granular disinfectant for treatment of drinking water complete all as specified and qty as per requirement and as directed by Engr-in-Charge. Make: Puri chlor brand of M/S Sree Rayalaseema Hi-strength Hypo Ltd. |
| 115 | Supply and fixing in replacement of Bronze gate valve for 15mm bore pipe, with iron wheel head, screwed both ends for iron pipe and fixed, ISI marked conforming to IS 778: 1984, complete all as specified and directed. |
| 116 | All as per serial item No. 102.00 here-in-before but of size 20mm bore -ditto-. |
| 117 | All as per serial item No. 102.00 here-in-before but of size 25mm bore -ditto-. |
| 118 | All as per serial item No. 102.00 here-in-before but of size 40mm bore -ditto-. |
| 119 | All as per serial item No. 102.00 here-in-before but of size 50mm bore -ditto-. |
| 120 | Taking out unserviceable/defective/damaged/blockage GI pipe 15 mm bore steel water tubing, including fitting and removing away all unserviceable pipe from site, complete all as specified and as directed. (Note: Exacavation and earhwork shall be measured and paid for separately.) |
| 121 | All as per serial item No. 107.00 here-in-before but of size 20mm bore -ditto-. |
| 122 | All as per serial item No. 107.00 here-in-before but of size 25 mm bore -ditto-. |
| 123 | All as per serial item No. 107.00 here-in-before but of size 40mm bore -ditto-. |
| 124 | All as per serial item No. 107.00 here-in-before but of size 50mm bore -ditto-. |
| 125 | All as per serial item No. 107.00 here-in-before but of size 80mm bore -ditto-. |
| 126 | All as per serial item No. 107.00 here-in-before but of size 100mm bore -ditto-. |
| 127 | All as per serial item No. 107.00 here-in-before but of size 150mm bore -ditto-. |
| 128 | Supply and fixing steel water tubing medium grade, galvanised, ISI Marked conforming to IS 1239 Part-I 2004, 15mm bore with and including all fittings such as bends , elbows,tees, short length , socket, union, check nuts, nipples, flanges and weldings etc. fixed and laid in trenches/floor/under culvert/road crossing etc including testing complete all as specified and as directed. |
| 129 | All as per serial item No. 115.00 here-in-before but of size 20mm bore -ditto-. |
| 130 | All as per serial item No. 115.00 here-in-before but of size 25mm bore -ditto-. |
| 131 | All as per serial item No. 115.00 here-in-before but of size 40mm bore -ditto-. |
| 132 | All as per serial item No. 115.00 here-in-before but of size 50mm bore -ditto-. |
| 133 | All as per serial item No. 115.00 here-in-before but of size 80mm bore -ditto-. |
| 134 | All as per serial item No. 115.00 here-in-before but of size 100mm bore -ditto-. |
| 135 | All as per serial item No. 115.00 here-in-before but of size 150mm bore -ditto-. |
| 136 | Cleaning of RCC OH Tank of capacity 50000 Gln on staging 20 feet height throughly removing mud, grits etc. from the sump by following method:- (a) Removing all dirt,mud with the help of containers mannually from inside to the water storage Sump, then scraping to walls/pillars/floor complete as directed. (b) Washing with clean water after scraping with wire brush in side and removing mud and spoil to a distance n.exc. 50 mtrs.(c) Washing with clean water and bleaching powder including scraping wire brush on walls/pillars/floor removing mud, grits & deposits etc properly. (d) Repair/ Replacement to all inlet/out lets of sump with a reqd size of MS/GI Pipe as directed including cement work etc complete leakage proof.(MS/GI Pipe if reqd, it will be measured and paid separately).(e) Dry washed walls, coating with a one coat of white cement in side and out side two coat of white wash with lime the whole surface of walls/pillars and floor/roof of sump. |
| 137 | Cleaning of RCC UG sump of capacity 100000 Gln on staging 20 feet height throughly removing mud, grits etc. from the sump by following method:- (a) Removing all dirt,mud with the help of containers mannually from inside to the water storage Sump, then scraping to walls/pillars/floor complete as directed. (b) Washing with clean water after scraping with wire brush in side and removing mud and spoil to a distance n.exc. 50 mtrs.(c) Washing with clean water and bleaching powder including scraping wire brush on walls/pillars/floor removing mud, grits & deposits etc properly. (d) Repair/ Replacement to all inlet/out lets of sump with a reqd size of MS/GI Pipe as directed including cement work etc complete leakage proof.(MS/GI Pipe if reqd, it will be measured and paid separately).(e) Dry washed walls, coating with a one coat of white cement in side and out side two coat of white wash with lime the whole surface of walls/pillars and floor/roof of sump. |
| 138 | Cleaning of RCC UG sump of capacity 30000 Gln on staging 20 feet height throughly removing mud, grits etc. from the sump by following method:- (a) Removing all dirt,mud with the help of containers mannually from inside to the water storage Sump, then scraping to walls/pillars/floor complete as directed. (b) Washing with clean water after scraping with wire brush in side and removing mud and spoil to a distance n.exc. 50 mtrs.(c) Washing with clean water and bleaching powder including scraping wire brush on walls/pillars/floor removing mud, grits & deposits etc properly. (d) Repair/ Replacement to all inlet/out lets of sump with a reqd size of MS/GI Pipe as directed including cement work etc complete leakage proof.(MS/GI Pipe if reqd, it will be measured and paid separately).(e) Dry washed walls, coating with a one coat of white cement in side and out side two coat of white wash with lime the whole surface of walls/pillars and floor/roof of sump. |
| 139 | Cleaning of RCC Semi UG sump of capacity 10000 Gln on staging 10 feet height throughly removing mud, grits etc. from the sump by following method:- (a) Removing all dirt,mud with the help of containers mannually from inside to the water storage Sump, then scraping to walls/pillars/floor complete as directed. (b) Washing with clean water after scraping with wire brush in side and removing mud and spoil to a distance n.exc. 50 mtrs.(c) Washing with clean water and bleaching powder including scraping wire brush on walls/pillars/floor removing mud, grits & deposits etc properly. (d) Repair/ Replacement to all inlet/out lets of sump with a reqd size of MS/GI Pipe as directed including cement work etc complete leakage proof.(MS/GI Pipe if reqd, it will be measured and paid separately).(e) Dry washed walls, coating with a one coat of white cement in side and out side two coat of white wash with lime the whole surface of walls/pillars and floor/roof of sump. |
| 140 | Cleaning of RCC Semi UG sump of capacity 5000 Gln on staging 10 feet height throughly removing mud, grits etc. from the sump by following method:- (a) Removing all dirt,mud with the help of containers mannually from inside to the water storage Sump, then scraping to walls/pillars/floor complete as directed. (b) Washing with clean water after scraping with wire brush in side and removing mud and spoil to a distance n.exc. 50 mtrs.(c) Washing with clean water and bleaching powder including scraping wire brush on walls/pillars/floor removing mud, grits & deposits etc properly. (d) Repair/ Replacement to all inlet/out lets of sump with a reqd size of MS/GI Pipe as directed including cement work etc complete leakage proof.(MS/GI Pipe if reqd, it will be measured and paid separately).(e) Dry washed walls, coating with a one coat of white cement in side and out side two coat of white wash with lime the whole surface of walls/pillars and floor/roof of sump. |
| 141 | Supply only water quality Test Kit for Bromine,Chlorine and PH level for daily testing of quality of Water at various supply point of Solan. |
| 142 | Excavation in trenches in hard dense soil n.exc 1.5 mtr wide & n.exc 1.5mtr in depth and n. exc. 10sqm on plan for laying pipe in trenches and getting out complete all as specified and directed. |
| 143 | Returning filling in trenches, spreading, levelling, watering and well ramming in layers n.exc 25cm in hard dense soil complete all as specified and directed. |
| 144 | Removing of surplus soil to a distance n.exc 50 mtr and depositing where directed at a level n.exc 1.5 mtr above starting point complete all as specified and directed. |
| 145 | Taking down carefully any type of battens or conduit point wiring with or except conduit (light, fan, socket or power) complete including fittings and fixtures such as switches, sockets, ceiling roses, lamp holders, pendent light fittings, MCBs / isolators, fan regulators, tube light fittings etc removing material from site and making good disturbed surfaces of walls, ceilings etc including two coats of white / colour washing / distempering etc to match the existing complete all as directed by Engineer - in - Charge. |
| 146 | Material & labour for point wiring with 1.5 Sq.mm nominal cross sectional area, single core, 1100 Volts grade, multi stranded, FRLSH PVC insulated, unsheathed copper conductor cable in and including PVC concealed conduit of 20 mm dia or higher, medium grade complete with and including all PVC conduit accessories / fittings, brass screws, washers etc, sunk zinc coated pressed steel terminal boxes including all cutting holes in or through walls, making good to walls, ceiling etc including two coats of white / colour washing / distempering etc to the disturbed surfaces to match the existing with 3mm thick plastic laminated sheet top cover concealed in wall with and including continuous earth wire of size 1.5 Sqmm nominal cross sectional area, single core, PVC insulated stranded FRLSH copper conductor cable, unsheathed and connected to common earth and earth dolly complete all as specified and directed for the followings :- |
| 147 | One light / fan point controlled by one, one way switch 05 / 06 Amps complete all as specified and directed. |
| 148 | One bell/buzzer point controlled by one, one way switch 05/06 Amps complete all as specified and directed. |
| 149 | One 3 pin, 05 / 06 Amps socket outlet point on independent board controlled by one, one way 05 / 06 Amps switch complete all as specified and directed. |
| 150 | One 3 pin, 05 / 06 Amps socket outlet point on same board controlled by one, one way 05 / 06 Amps switch complete all as specified and directed. |
| 151 | One two way point controlled by two, two way switches 05 / 06 Amps complete all as specified and directed. |
| 152 | All as per serial item No 133.03 here - in - before but with 2.5 Sqmm nominal cross sectional area copper conductor cable for one 15 / 16 Amps socket outlet point on independent board complete all as specified and directed. |
| 153 | Supply and fix modular switch, 6 Amp, one way complete all as specified and directed by Engr-in-Charge. |
| 154 | Supply and fix modular switch, 16 Amp, one way complete all as specified and directed by Engr-in-Charge. |
| 155 | Supply and fix modular switch, 6 Amp, two way complete all as specified and directed by Engr-in-Charge. |
| 156 | Supply and fix modular bell push, 6 Amp, one way complete all as specified and directed by Engr-in-Charge. |
| 157 | Supply and fix modular socket 6 Amp 2/3 pin combined 2 module complete all as specified and directed by Engr-in-Charge. |
| 158 | Supply and fix modular socket 6/16 Amp 2/3 pin combined 2 module complete all as specified and directed by Engr-in-Charge. |
| 159 | Supply & fixing lamp holder (Angular / Straight), insulated body, with back plate for batten fitting all as specified and directed by Engr-in-Charge. |
| 160 | Supply and fix LED 9 W 3 STAR LAMP, lumen out put 525 lm,colour temp 6500K, length 102mm , dia 56mm and amp 0.03A Model : Make Havells or equivalent ,complete all as specified and directed by Engr-in-Charge. |
| 161 | Supply and fixing LED lights fitting batten type 20W, 220V, AC decorative box type with driver, including LED tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete all as specified and directed by Engr-in-Charge. Model: Make Havell's or equivalent make as mentioned in Appx'B' of CA. |
| 162 | Supply and fixing LED light fitting mirror type batten with high out put diffuser 2 feet, 10 watt 220 V AC decorative type with driver holder and LED lamp including connecting up with three core flexible copper conductor cable of suitable size Model : Make Havell's or equivalent make as mentioned in Appx'B' of CA. |
| 163 | Supply and fixing LED light fitting 1x9W/1X10W bulkhead luminaires including LED light driver holder connecting up with three core flexible copper conductor cable of suitable size all as specified and directed by Engr-in-Charge. |
| 164 | Supplying & Fixing Decorative Wall light fixture made up of Polycarbonate, suitable for 1X9W retrofit LED lamp ( B-22 base), Model : CITY 1 of Make Havell's or equivalent make as mentioned in Appx'B' of CA. |
| 165 | Supply & fixing of ceiling rose, 3 phase/PVC/polycarbonate isolated body complete all as specified & directed by Engineer -in- Charge. |
| 166 | Supply and fixing LED bldg security/street light fitting 35 Watt 230 V AC outdoor type with high pressure die cast aluminum hosing and heat resistant complete with driver, lamp bracket with impact and corrosion resistant including thermal management in multiple optics complete with IP 65/66 protection complete all as specified & directed by Engineer -in- Charge. |
| 167 | Supply and fix exhaust fan, steel body AC single Phase. 230V of size 300mm sweep with, blades, frame and louvers including taking down unserviceable and depositing to E/M Store complete all as specified and directed by Engr-in-Charge. |
| 168 | Taking down carefully unserviceable Sub main wiring of any size and type, removing material from site for taking credit and making good the disturbed surfaces of walls, ceilings etc including two coats of white / colour washing / distempering etc to match the existing complete all as specified and directed by Engineer - in - Charge. |
| 169 | Material and labour for sub main wiring with 2x6 Sqmm nominal cross sectional area (two single core cable of 6 Sqmm for Phase and neutral + 1 single core cable of 6 Sqmm for earth wire), 1100 Volts grade, stranded, PVC insulated, unsheathed, copper conductor cable FRLSH with and including continuous earth wire of size 6 Sqmm nominal cross sectional area, single core, PVC insulated, copper conductor cable drawing into and including rigid non metallic PVC concealed conduit of 25 mm dia, medium grade with all conduit accessories / fittings, brass screws, washers etc and connected to common earth dully including all cutting / chases etc in wall, making good to walls etc including two coats of white / colour washing / distempering etc to the disturbed surfaces to match the existing complete all as specified & directed by Engineer - in - Charge. |
| 170 | Ditto all as item No 151.00 above, but by using two single core cable of 10 Sqmm for Phase and neutral + 1 single core cable of 10 Sqmm for earth wire complete all as specified & directed by Engineer - in - Charge. |
| 171 | Taking down carefully unserviceable distribution board of any capacity including wooden board and making good the disturbed surfaces of walls, etc including two coats of white / colour washing / distempering etc to match the existing complete all as directed by Engineer - in - Charge. |
| 172 | Supply and fixing sheet metal enclosure double door, single pole and neutral, AC, 240 volts, 4 way, with 200 Amps rated copper bus bar and IP - 43 protection with metal double door and flush to wall including all cutting on wall and making good including two coats of white/colour washing/distempering etc to match the existing disturbed surfaces complete all as directed by Engineer - in - Charge. |
| 173 | -Ditto- all as per item No 154.00, but of size 08 way SPN. complete all as specified & directed by Engineer - in - Charge. |
| 174 | -Ditto- all as per item No 154.00, but of size 12 way SPN. complete all as specified & directed by Engineer - in - Charge. |
| 175 | Supply and fixing MCB, SP, AC, 240 volts \\"C\\" series capacity of 06 to 32 Amps, 10kA and making connections complete all as specified & directed by Engr - in - Charge. |
| 176 | Supply and fix in repair MCB single pole & neutral 32 Amps 240 volts, C series,10 kA rupturing capacity Make Polycab or equivalent make as mentioned in Appx'B' of CA. |
| 177 | Supply & fixing MCB, DP (Double Pole), AC, 240 volts, C series capacity 20 Amps to 32 Amps 10kA and making connections complete all as specified & directed by Engr - in - Charge. |
| 178 | Supply & fixing MCB, DP (Double Pole), AC, 240 volts, C series capacity 40 Amps to 63 Amps 10kA and making connections complete all as specified & directed by Engr - in - Charge. |
| 179 | Supply and fixing sheet metal enclosure, Triple pole and neutral AC, 415 volts, 04 way, with 200 Amps rated copper bus bar and IP - 43 & IK 09 protection including provision of four pole 100 Amp isolator and MCBs of cap 20 to 40 Amps as incomer with metal double door and flush to wall including all cutting etc on wall and making good including two coats of white / colour washing / distempering etc to match the existing disturbed surfaces complete all as directed by Engineer - in - Charge. |
| 180 | Supply & fix Isolator 4 Pole 'C' series 100 amps capacity AC 415 V,10kA complete all as specified and directed by Engineer - in - Charge. |
| 181 | Material and labour for Sheet metal enclosure including fiiting on wall including and making the connection with MCCB 4 Pole 100 Amps 25KA, 415 volts , 50 Hz ,thimble/lugs, aslo including all nuts bolts required for fixing all as specified and directed by Engineer - in - Charge. |
| 182 | Supply & fixing industrial type SPN enclosure with a two pin and earth plug and socket complete with and including 32 Amps MCB, single pole, AC, 240 volts and flush to wall including all cuttings & chases etc on wall and making good including two coats of white / colour washing / distempering etc to match the existing disturbed surfaces complete all as directed by Engineer - in - Charge. |
| 183 | Material & labour for earthing complete with galvanised mild steel earth plate electrode 60cmx60cmx6mm thick buried directly in ground (earth pit not less than 2.25mtr deep below ground level) with top edge of the plate not less than 1.5mtr below normal ground level steel earth plate connected with GI wire 04mm dia by means of lug, bolts, nuts, check nuts, washers of galvanised iron or steel GI protection pipe 15mm bore light grade all as shown in elect plate No.5 of SSR part I connecting to main switch board / Main DB’s including excavation, earth work, salt and charcoal dust mixed and packed 150mm thick around GI earth plate, GI pipe medium grade 20mm nominal bore watering pipe GI sheet funnel wire mesh, concrete pit, RCC cover in PCC 1:2:4 type B1 duly reinforced with MS Bars 6mm dia at the rate of 150mm center to center both way with suitable lifting handle and pit / chamber in PCC 1:3:6 type C1 , Angle iron 40x40x5mm frame for pit cover including testing on completion complete all as specified and directed by Engr - in - Charge. |
| 184 | Taking down carefully service connection/under ground cable of any size and making good to disturbed surface as per existing complete all as specified and directed by Engr - in - Charge. |
| 185 | Supply and laying or fixing or passing through pipe, 1100 volts grade heavy duty cable with PVC insulated aluminium conductor served with an inner sheathing of PVC tape armoured with galvanised steel wire or tape and overall PVC sheathed 4 sq. mm 2 core nominal cross section in service connections complete all as specified and directedby Engr - in - Charge. |
| 186 | Supply and laying or fixing or passing through pipe, 1100 volts grade heavy duty cable with PVC insulated aluminium conductor served with an inner sheathing of PVC tape armoured with galvanised steel wire or tape and overall PVC sheathed 6 sq. mm 2 core nominal cross section in service connections complete all as specified and directed by Engr - in - Charge. |
| 187 | Supply and laying or fixing or passing through pipe, 1100 volts grade heavy duty cable with PVC insulated aluminium conductor served with an inner sheathing of PVC tape armoured with galvanised steel wire or tape and overall PVC sheathed 10 sq. mm 2 core nominal cross section in service connections complete all as specified and directed by Engr - in - Charge. |
| 188 | Supply and laying or fixing or passing through pipe, 1100 volts grade heavy duty cable with PVC insulated aluminium conductor served with an inner sheathing of PVC tape armoured with galvanised steel wire or tape and overall PVC sheathed 16 sq. mm 2 core nominal cross section in service connections complete all as specified and directed by Engr - in - Charge. |
| 189 | Dismantling house service brackets, any type |
| 190 | Supply and fixing House service bracket (hook type complete with 3.0m long G.I. pipe 40 mm dia Med. grade, two nos 90 deg bends. M.S. hook and stay or guy . |
| 191 | Taking down after disconnecting electric connection 25/35/50 Ltrs storage water heater geysers, descalling and repair /replacement of un-serviciable spare and reassembling, recommissioning and testing complete all as per specified and directed. (Note - Spare parts will measured and paid saperetely under relevent items of schedule). |
| 192 | Supply and fixing in repair innner water container ISI Marked made of SS, vertical or horizontal type for 25 ltr to 50 ltr capacity geysers (as per existing sample) complete all as specified and directed. by Engr - in - Charge. |
| 193 | Supply and fixing cast copper alloy CP apparatus plate assembly (ISI Marked) with rubber washer suitable for 25 to 50 Ltrs capacity Geysers after taking out u/s aperature plate complete all as ditected. by Engr - in - Charge. |
| 194 | Supply and fixing fusible plug for geysers melting at 95 degree centigrade ( any special required for for fixing plug shall be supply without any financial implication after taking down old unserviceable fusible plug complete all as directed. by Engr - in - Charge. |
| 195 | Supply and fixing in repair indicators lamp round /rectangular type for any type or size capacity after taking down old unserviceable indicator lamp complete all as directed.by Engr - in - Charge. |
| 196 | Supply and fixing Heating Element ISI Marked round/ tringular base, push type or thread type including rubber washer for 1.5/2.0 KW suitable for geysers 25 Ltrs to 50 Ltrs capacity (as per existing sample) including taking down unserviceable complete all as specified and as directed. by Engr - in - Charge. |
| 197 | Supply & fix of geyser element 1.5 /2.0 KW capacity porcealen type of size 12 to 15 inch complete with clamps, nuts and bolts washers etc for geysers ISI marked (any Make) complete all as specified and directed. by Engr - in - Charge. |
| 198 | Supply and fixing thermostat ISI Marked suitable for geysers 25 Ltrs to 50 Ltrs capacity (as per existing sample) including taking down unserviceable complete all as specified and as directed. by Engr - in - Charge. |
| 199 | Supply and fixing PVC connections 450mm long for Hot/Cold water of 15mm size with cromium nuts and washsers fixed as in repairs complete all as specified.by Engr - in - Charge. |
| 200 | Supply only Capacitor 4 /3.15 mfd capacity item code QHPCWC5004X0 for exhaust fan on any sweep. complete all as specified and directed by Engr-in-Charge. |
| 201 | Supply and fix in replacement electric water heater, storage type steel body with copper inner tank and heating element upto 2 KW capacity 25 litre, BEE 5 Star rated complete with all accessories such as safety valve, thermostate, NRV, connection piece etc.and including taking down unserviceable and deposit to E/M Store. Note:- Geyser will be fitted with fastners-04 Nos including bolts washers etc and making good disturbed surface complete all as specified and directed by Engr-in-Charge. |
| 202 | Taking down exhaust fan dismantling and painting of exhaust fan complete at site with synthetic enamel paint by spraying incl (fittings with filler) one coat after cleaning all dust etc incl connecting up. Provn of twin core cable of suitable size for ceiling rose to connector connecting of earth wire incl replacement of capacitor, bearing/bush, rubber bushes minor nuts bolts screws washers greassing in fan bearing & refix same complete all as directed. |
| 203 | Material and labour for rewinding of 300mm sweep Exhaust fan with appropriate size of copper enamelled wire including varnishing ,heating with proper insulation complete and testing all as specified and directed. |
| 204 | Taking down carefully by unscrewing from boards/outlet boxes, fittings and fixtures such as switches, sockets, ceiling roses, lamp holders, brackets, ceiling fittings, bulk head fittings, tube light fittings and regulators, etc. for reuse at site or carrying to the store (To be measured only when found serviceable in all respects complete for reuse)of any type and size and making good the disturbed surfaces/walls, etc including two coats of white / colour washing / distempering etc to match the existing complete all as directed by Engineer - in - Charge. |
| 205 | Supply and fixing in replacement existing LED lights fitting batten type 20W, 220V, AC decorative box type with driver, including LED tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete all as specified and directed by Engr-in-Charge. |
| 206 | Supply and fixing LED Building security light 30 watt LED Inverter RTC inbuilt for AUTOON/AUTO OFF and must have dimming facility from 10 to 100% of rated wattage as peruser defined timeline made pressure die cast housing with individuals LEDs & Lens with modular secondary optics and IP65 protection with electronics driver and copper conductor 3 core of 0.7 sqmm from ceiling rose to security light with Bracket made out of GI light grade pipe of 32 mm dia 1.5 mtr long bend to an angle of 120 degree with fixing arrangements on wall Complete all as in repair. Make: Halonix Model: HLSLD-ML04-30-CWL-INV-RTC-DIMM, Wipro or Philips. |
| 207 | Supply and fixing in repair/replacement to existing surface light any type with 15 watt 220 volts AC surface/recessed type with high efficiency PMMA diffuser soft glare free light complete with drivers, holders, LED lamp suitable for roof ceiling including connecting up with three core flexible copper conductor cable of suitable size complete all as specified & directed by Engineer -in- Charge. |
| 208 | Supply and fixing in repair/replacement to existing LED light fitting 1x9W/1X10Wbulkhead luminaires including LED light driver holder connecting up with three core flexible copper conductor cable of suitable size all as specified and directed by Engr-in-Charge. |
| 209 | Supply and fix in repair/replacement to existing LED ADORE 9 W B22 CDL 3 STAR LAMP, odering code LHLDEUEBML8R005, lumen out put 525 lm,colour temp 6500K, length 102mm , dia 56mm and amp 0.03A complete all as specified and directed by Engr-in-Charge. |
| 210 | Supply and fix in repair/repair/replacement to existing post top lantern LED type 20 watt 230 watt volts AC outdoor type with decorative post top for 360 degree indirect light IP 65 protection with impact and corrosion resistant complete with driver and lamp complete all as specified and directed by Engr-in-Charge. |
| 211 | Supply and fix in repair/replacement to existing switch piano flush type, 05 / 06 Amps single pole, one way 240 volts complete all as specified & directed by Engr-in-Charge. |
| 212 | Supply and fix in repair/replacement to existing socket outlet 5 pin, 05 / 06 Amps flush type 240 volts complete all as specified & directed of maby Engr-in-Charge . |
| 213 | Supply and fix in repair/replacement to existing switch piano flush type, 15 / 16 Amps single pole, one way 240 volts complete all as specified & directed by Engr-in-Charge. |
| 214 | Supply and fix in repair/replacement to existing socket outlet 3 pin, 05 / 06 Amps and 3 pin 15 / 16 Amps (2 in 1 Multipurpose) 240 volts complete all as specified & directed by Engr-in-Charge. |
| 215 | Supply and fix in repair/replacement to existing switch bell push flush type , 5 amps , 240 volts all as directed by Engr-in-Charge |
| 216 | Supply and fix in repair/replacement to existing door bell ding dong type , 240 volts AC complete all as specified and directed by Engr-in-Charge. |
| 217 | Supply and fix in repair/replacement to existing switch piano flush type, 05 / 06 Amps single pole, two way 240 volts complete all as specified & directed. by Engr-in-Charge. |
| 218 | Supply and fix in repair/replacement to existing MCB, SP, AC, 240 volts \\"C\\" series capacity of 06 to 32 Amps, 10kA and making connections complete all as specified & directed. by Engr - in - Charge. |
| 219 | Supply & fix in repair/replacement to existing MCB, DP (Double Pole), AC, 240 volts, C series capacity 40 Amps to 63 Amps 10kA and making connections complete all as specified & directed. by Engr - in - Charge. |
| 220 | Supply and fix electronic meters temper proof LCD display with polycarbonate cover 230 V, 10-60Amp, accuracy class-I 50Hz, conforming to IS 13779, IP-54, with parameters to show data, time,current reading, load, PF, voltage and KWH including taking down unserviceable and depositing to E/M Store complete all as specified and directed by Engineer-in-Charge. |
| 221 | Supply and fixing steel meter box of size 90x95x20 cm box with thickness of steel 2mm including double door for opening with lockable arrangement incl steel knob, hinges, plater for hanging of meter 02 Nos and DBs 03 Nos etc with 4mm thick plain glass (size 6\\"x6\\") for provn of meter reading complete all as specified and directed by Engineer-in-Charge. |
| 222 | Amount of credit of Rs. 170154.60 for retrived old material as mentioned in Schedule 'A' section-II of tender document in pdf form, will be deducted offline while acceptence of tender. Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Sep 23, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedOct 14, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 19 daysOct 16, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 21 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender