Tender For special Repair To Bldg No. P-400 (Otm Accn) Of Rajput, Addn/Altn To Bathroom Of Bldg No. 490, Construction Of Facilities Block At Swc Rock Climbing Node And Addn/Altn To Hav Chandepal Thakur Kc Shooting Range At Mil Stn Alwar.
Tender Value
48.29 Lakhs
Estimated cost
Bid Submission
15 Oct 2026
16 days left
EMD
97000
Bank guarantee accepted
Document Fee
500
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Alwar → Rajasthan
EMD Exemption
Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for special Repair To Bldg No. P-400 (Otm Accn) Of Rajput, Addn/Altn To Bathroom Of Bldg No. 490, Construction Of Facilities Block At Swc Rock Climbing Node And Addn/Altn To Hav Chandepal Thakur Kc Shooting Range At Mil Stn Alwar.
BOQ
| Sl. No. | Item Description |
| 1 | Demolition of brick/stone masonry built in cement/lime mortar of any mix, including quoins, pillars and ashlar masonry, and removal of demolished material complete, all as specified and directed. |
| 2 | Dismantling stone slabs or tiles of any description and thickness in floors etc., laid dry or laid dry and pointed, complete all as specified and directed. |
| 3 | Demolition of cement concrete (unreinforced) in ground floors and paving, not exceeding 15 cm thickness, below or above ground level, including removal of rubbish complete, all as specified and directed. |
| 4 | Taking down chowkatts or frames with shutters, without taking off shutters from frames, exceeding 1.50 Sqm but not exceeding 4.00 Sqm each, and removing to store, complete all as specified and directed. |
| 5 | Taking down chowkatts or frames with shutters, without taking off shutters from frames, not exceeding 1.50 Sqm each, and removing to store, complete all as specified and directed. |
| 6 | Dismantling wrought iron or mild steel work of any description not otherwise provided for, complete all as specified and directed. |
| 7 | Dismantling floor, hearth or wall tiling including cement mortar bedding but not backing, removing serviceable tiles to store and rubbish off the premises, complete all as specified and directed. |
| 8 | Taking down cement plaster of any description from brick or stone surfaces, complete all as specified and directed. |
| 9 | Taking up or down 15 mm bore steel tubing and connections, complete all as specified and directed. |
| 10 | Taking up or down 20 mm bore steel tubing and connections, complete all as specified and directed. |
| 11 | Dismantling/demolishing water tanks of capacity not exceeding 1000 litres and removing from site, complete all as specified and directed. |
| 12 | Dismantling 110 mm bore PVC (SWR) drain pipe along with fittings and accessories, jointed in cement mortar, including taking out from walls, floors or trenches where required, complete all as specified and directed. |
| 13 | Dismantling 75 mm bore PVC (SWR) drain pipe along with fittings and accessories, jointed in cement mortar, including taking out from walls, floors or trenches where required, complete all as specified and directed. |
| 14 | M&L for brickwork with fly ash bricks conforming to IS 13757, old size bricks, straight or curved on plan exceeding 6 metre mean radius, built in cement mortar 1:6, complete all as specified and directed. |
| 15 | M&L for brickwork with fly ash bricks conforming to IS 13757, old size bricks, straight or curved on plan to any radius, in half-brick thick walls, built in cement mortar 1:4, complete all as specified and directed. |
| 16 | S&F solid PVC door frame 50 mm x 47 mm made out of 5 mm plain coloured PVC sheet reinforced with MS square tube, supplied and fixed in openings complete as per specification and drawing. |
| 17 | S&F factory-made solid PVC moulded door shutter 28 to 30 mm thick, with 2, 4 or 6 raised-panel design, 2 mm thick moulded pre-laminated PVC sheet on front face and 2 mm plain coloured PVC sheet on back face, supplied and fixed to frame complete as per specification and drawing. |
| 18 | S&F 35 mm thick second-class hardwood factory-made panelled door shutter, two-panel type, with lock rail and panel of 9 mm BWP commercial plywood or 12 mm veneered particle board with commercial veneering on both faces, members as specified, kiln seasoned, chemically pressure treated and fixed to chowkatts complete. |
| 19 | S&F 35 mm thick second-class hardwood glazed and skeleton shutters, open rebated and prepared to receive glass/gauze etc., without sash bars, edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass etc., complete all as specified and directed. |
| 20 | S&F factory-made box-type steel windows with side-hung shutters, including projecting-type hinges, 150 mm steel handle and steel peg stay, complete with glazing bars, fabricated with standard-size members as shown on drawings, including frames complete all as specified. Rate shall include lugs and fittings required for fixing wire cloth, sheet glass, grills, ironmongery and guard bars as shown on drawings. |
| 21 | S&F steel ventilator with top-hung shutter including hinges and steel peg stay, complete, including taking down existing ventilator, all as specified and directed. |
| 22 | M&L framed steel work such as grills, gratings, framed guard bars, barred iron doors, ladders, cooler stands, framed balusters, walkways, railings, framework of water tanks and similar work conforming to Fe 290 Grade E-165, complete all as specified and directed. |
| 23 | M&L bands, straps, supports or stays for rainwater/ventilating pipes, including bolts where required, hooks, hook and pintle hinges, hasps and staples, chains, hand-made sliding bolts, clamps, holdfasts, wall ties, fan hooks, plain angle cleats, knee-piece inserts, two-way/three-way straps, plate washers and similar small articles conforming to Fe 290-0 Grade E-165, complete all as specified and directed. |
| 24 | S&F stainless steel wire cloth of 0.36 mm nominal wire diameter and average aperture width 1.40 mm, fixed with stainless steel staples/nails/screws, complete all as specified and directed. |
| 25 | S&F ordinary-quality sheet glass, 4 mm thick, in panes not exceeding 0.50 Sqm each, fixed complete all as specified and directed. |
| 26 | M&L for preparation of new wooden surfaces exceeding 10 cm width or girth and applying two coats of synthetic enamel paint over one coat of pink primer, complete all as specified and directed. |
| 27 | M&L for preparation of new steel surfaces of any description exceeding 10 cm width or girth and applying two coats of synthetic enamel paint over one coat of red oxide primer, complete all as specified and directed. |
| 28 | S&F stainless steel butt hinges, 100 mm long, medium weight, fixed complete. |
| 29 | S&F anodised aluminium barrel tower bolt, 150 mm long, of extruded section, fixed complete. |
| 30 | S&F anodised aluminium 'D' type handle, 150 mm long, fixed complete all as specified and directed. |
| 31 | S&F floor door stopper, 150 mm long, of anodised aluminium-alloy body and tongue with hard-drawn steel spring, fixed in floor complete. |
| 32 | S&F anodised aluminium-alloy sliding door bolt, 300 mm long, with hasp, staple, fixing clips and bolts, fixed complete. |
| 33 | M&L glazed coloured ceramic tiles 450 x 350 x 7 mm thick in vertical surfaces, set and jointed in neat cement slurry and pointed with white/coloured cement to match shade of tiles, over and including 10 mm thick rendering in CM 1:4, complete all as specified and directed. |
| 34 | M&L non-skid coloured ceramic tiles 7 to 8 mm thick, square/rectangular, area of each tile exceeding 0.06 Sqm but not exceeding 0.11 Sqm, in floors, set and jointed in neat cement slurry and pointed with matching white/coloured cement over and including 15 mm thick screed bed in CM 1:6, complete. |
| 35 | M&L non-skid white ceramic tiles 7 to 8 mm thick, square/rectangular, area of each tile exceeding 0.11 Sqm but not exceeding 0.18 Sqm, in floors, set and jointed in neat cement slurry and pointed with matching white/coloured cement over and including 15 mm thick screed bed in CM 1:6, complete. |
| 36 | M&L green marble work 18 to 20 mm thick, table rubbed and polished, in steps, jambs, pillars, window cills, cooking platforms and the like, laid in CM 1:4 including pointing in white cement 1:2 using marble dust and pigment to match marble shade, complete. |
| 37 | M&L machine-cut Kota stone slab flooring 18 to 20 mm thick, size not less than 22\\" x 22\\", laid and jointed with grey cement slurry mixed with pigment to match shade, over and including 20 mm thick screed bed in CM 1:6, including rubbing and mirror polishing, complete. |
| 38 | M&L Kota stone slab 18 to 20 mm thick in risers of steps, skirting, dado and pillars, laid and jointed with grey cement slurry mixed with matching pigment over and including 10 mm thick rendering in CM 1:4, including cutting, moulding outer edges, rubbing and mirror polishing, complete. |
| 39 | M&L 75 mm thick PCC 1:3:6 Type C2 using 40 mm graded stone aggregate in plinth protection, finished fair and even using extra cement for smooth finish, complete. |
| 40 | S&F powder-coated aluminium frames for doors, windows and ventilators with one or more rebates, minimum powder-coating thickness 50 micron, including joining cleats and fixing arrangements, complete. |
| 41 | S&F powder-coated aluminium window/ventilator shutters, side-hung type without sash bars, minimum powder-coating thickness 50 micron, aluminium section weighing 0.55 Kg/m, including joining cleats, glazing clips, rubber packing, aluminium snap beading, screws, peg stay 150 mm long, B-1 hinges 100 mm long and suitable handle, complete. |
| 42 | M&L rendering 10 mm thick in CM 1:6 on brickwork, stone or concrete surfaces, finished even and smooth without using extra cement, complete. |
| 43 | M&L rendering 15 mm thick in CM 1:4 on brickwork/stone/concrete wall surfaces, finished even and smooth without using extra cement, with waterproofing compound measured and paid separately, complete. |
| 44 | Supply only integral waterproofing compound, complete as specified. |
| 45 | M&L rendering 5 mm thick in CM 1:3 on concrete ceiling surfaces, finished even and smooth without using extra cement, complete. |
| 46 | M&L for preparation of new surfaces and applying two or more coats of 100% premium acrylic exterior emulsion paint, VOC less than 50 gm/litre and UV resistant as per IS 15489:2004, alkali, fungal and dirt resistant, of required shade, with silicon additives @ 1.43 litre/10 Sqm over and including exterior primer @ 0.90 litre/10 Sqm, complete. |
| 47 | M&L for providing and applying minimum 1 mm thick wall-care putty over prepared surfaces to achieve an even and smooth surface for painting, complete all as specified and directed. |
| 48 | M&L for complete removal of existing treatment from stone/plastered wall surfaces and applying 1 mm thick wall-care putty, exterior primer @ 0.90 litre/10 Sqm and two or more coats of 100% premium acrylic exterior emulsion paint with silicon additives @ 1.43 litre/10 Sqm, VOC less than 50 gm/litre, UV, alkali, fungal and dirt resistant, of required shade, complete. |
| 49 | M&L for preparation of new plastered wall surfaces and applying three coats of white wash, complete all as specified and directed. |
| 50 | M&L for preparation of newly plastered/unplastered ceiling surfaces and applying three coats of white wash, complete all as specified and directed. |
| 51 | M&L for preparation of newly plastered wall surfaces and applying two coats of oil-bound distemper of approved shade over one coat of alkali-resistant primer and including 1 mm thick wall-care putty, complete. |
| 52 | M&L for complete removal of existing treatment including cleaning mortar drops, smoke soot, mould, moss, efflorescent salts, oil and greasy spots from old decorated wall surfaces and applying two coats of oil-bound distemper of approved shade/tint including 1 mm thick wall-care putty, complete. |
| 53 | M&L for brooming down old decorated plastered/unplastered wall surfaces including cornices, pilasters etc. and applying one coat of white wash, complete. |
| 54 | All as per preceding item but on ceiling surfaces. |
| 55 | S&F medium-grade steel tubing, 15 mm bore, including all fittings, fixed to walls and/or laid in floors, complete. |
| 56 | S&F medium-grade GI tubing, 20 mm bore, including fittings, fixed to walls/floors, complete. |
| 57 | S&F in repair PVC connection pipe 15 mm dia x 600 mm long including adapters and washers at both ends, complete. |
| 58 | S&F rotational-moulded polyethylene water storage tank, 1000 litre capacity, cylindrical vertical closed-top type, hoisted and fixed in position, complete. |
| 59 | S&F in repair brass high-pressure ball valve with polyethylene float and fly net, screwed for 15 mm dia iron pipe, complete. |
| 60 | S&F in repair white vitreous china wash-hand basin, flat-back type, size 450 x 300 mm, fixed on and including new brackets, CP waste coupling and PVC waste pipe, complete. |
| 61 | S&F in repair fancy-type chromium-plated alloy bib tap, 15 mm bore, with crutch/butterfly handle, screwed-down type, fixed complete. |
| 62 | S&F in repair fancy-type chromium-plated alloy stop/angle valve, 15 mm bore, screwed-down high-pressure type, fixed complete. |
| 63 | S&F in repair 20 mm dia gunmetal globe/gate valve with iron wheel head, screwed both ends and fixed complete. |
| 64 | S&F in repair 15 mm bore swan-neck cast copper-alloy chromium-plated pillar tap, weight not less than 400 grams, screwed for iron pipe/brass ferrule and fixed complete. |
| 65 | S&F in repair PVC waste pipe, 32 mm bore, of suitable length for WHB/urinal/sink, complete. |
| 66 | S&F in repair soap dish of any type, fixed to plugs with chromium-plated brass screws, complete. |
| 67 | S&F in repair sheet-glass shelf assembly comprising 5.5 mm thick glass shelf, 120 mm wide and 600 mm long, with chromium-plated brackets, guard and railing, complete. |
| 68 | S&F in repair bevelled-edge mirror 600 x 450 mm of selected-quality glass mounted on 6 mm thick AC building board/commercial plywood and fixed to wooden plugs with CP brass screws and cup washers, complete. |
| 69 | S&F in repair white vitreous china squatting pan, Orissa pattern, size 580 x 440 mm, with integral footrests and P/S trap, including CC bedding, connection to trap and 32 mm dia polyethylene/PVC flush pipe and making good disturbed floor surfaces to match existing, complete. |
| 70 | S&F in repair PVC low-level flushing cistern, 10 litre capacity, white ISI marked, syphonic-action type including inlet ball valve, float, handle and brackets, fixed complete. |
| 71 | S&F 15 mm dia fancy-type CP cast copper-alloy pillar tap with capstan head, screwed-down high-pressure type, long screwed shank and fly nuts, fixed complete. |
| 72 | S&F in repair chromium-plated brass shower rose, 125 mm size, with swivel joint including fixing to 15 mm bore steel pipe/union, complete. |
| 73 | S&F in repair tubular towel rail, 20 mm dia, D-type, 600 mm long between flanges, brass chromium plated, fixed complete. |
| 74 | S&F rolled mild-steel framed work as in doors/gates of angle or other sections with gusset plates, rails and braces, drilled for fixing steel sheeting/covering and prepared for hanging/sliding, including hooks and hinges or steel hanging-door fittings, fastening and fixing complete, Grade Fe410-0/E-250. |
| 75 | S&F PVC (SWR) 110 mm single junction Tee, equal or unequal, complete. |
| 76 | S&F PVC (SWR) pipe, 75 mm bore, single socketed, any length, with rubber-ring joints, laid in trenches/floors/walls including removing old pipes and making good disturbed surfaces to match existing, complete. |
| 77 | S&F PVC (SWR) bend, 75 mm dia, any radius, complete. |
| 78 | S&F in repair PTMT grating dome, 100 mm dia, minimum weight 25 grams, fixed with cement, complete. |
| 79 | S&F in repair PVC (SWR) floor trap, 75 mm dia, plain with grating, including jointing with solvent cement, complete. |
| 80 | S&F in repair PVC (SWR) gully trap 125/110 mm, setting and jointing with solvent cement, complete. |
| 81 | S&F anodised aluminium grill of approved design/pattern, minimum anodic coating Grade AC-15, fabricated from approved standard sections and fixed to existing window frame with CP brass/stainless steel screws @ 200 mm centres, including cutting to proper opening size and fixing standard aluminium section around, complete. |
| 82 | S&F PVC (SWR) pipe, 110 mm bore, single socketed, any length, with rubber-ring joints, laid in trenches/floors/walls including removing old pipes and making good disturbed surfaces to match existing, complete. |
| 83 | S&F PVC (SWR) bend, 110 mm bore, any radius, complete. |
| 84 | S&F PVC (SWR) vent cowl, 110 mm dia, complete. |
| 85 | Demolition of mud/PCC roof padding of any thickness including plaster and existing treatment, whether full or part thickness is removed, including cleaning and preparing surface for further treatment and disposal of debris/rubbish to a distance exceeding 1 Km but not exceeding 1.5 Km, complete. |
| 86 | M&L rendering 15 mm thick in CM 1:4 with waterproofing compound over green concrete surface, finished even and smooth without using extra lime/cement; waterproofing compound shall be measured and paid separately, complete. |
| 87 | M&L applying evenly tack coat of industrial bitumen 85/25 @ 1.20 Kg/Sqm including cleaning surface over bituminous primer, complete. |
| 88 | M&L APP-based polymeric membrane, minimum weight 3 Kg/Sqm and minimum 3 mm thick, reinforced with polyester non-woven reinforcement/mat of minimum 150 gm/Sqm, laid by torch application method with 100 mm overlaps in both directions as per manufacturer's instructions, including two coats of reflective silver aluminium paint over APP membrane, complete. |
| 89 | Cutting holes in brick walls exceeding half-brick but not exceeding one-brick thick built in cement/cement-lime mortar, or stone walls built in lime mortar, for inserting holdfasts and making good disturbed portions in CM 1:3 or CC 1:2:4 Type B1 as required, complete. |
| 90 | Demolition of reinforced cement concrete in roofs, floors other than ground floors, beams, staircases, landings, chajjas and similar suspended work, complete. |
| 91 | M&L granite tiles of any type, 18 to 20 mm thick, machine cut, bedded and jointed with grey cement slurry and pointed with white cement mixed with pigment to match granite shade, including cutting and polishing over and including 20 mm thick screed bed in CM 1:6, complete. |
| 92 | M&L formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work not exceeding 200 mm thick, horizontal or sloping, for rough-finished concrete surfaces, complete. |
| 93 | M&L 75 mm thick PCC 1:4:8 Type D2 using 40 mm graded crushed stone aggregate in sub-base of floors, complete. |
| 94 | M&L machine-pressed precast concrete interlocking paver blocks of any shape and size, 60 mm thick, M-35 grade, conforming to IS 15658:2006, laid over sand cushioning, complete all as specified and directed. Note: Sand cushioning shall be measured and paid separately. |
| 95 | Supply and laying of sand including spreading, levelling and ramming in layers not exceeding 25 cm thick in each layer, complete all as specified and directed. |
| 96 | M&L PCC 1:2:4 Type B0 using 12.5 mm graded crushed stone aggregate, 25 mm thick, in floors, complete all as specified and directed. |
| 97 | S&F 4.5 mm thick plain-coloured linoleum laid dry in floors including stretching, cutting and fitting, sealed down with approved adhesive, complete. |
| 98 | S&F solid PVC wall lining consisting of 5 mm thick decorative coloured laminated PVC sheet including solvent cement and fixing at site on PVC frame, complete as per specification and drawing. |
| 99 | S&F 5 mm thick PVC sheet fillet, 35 mm wide, for wall panelling including fixing to wall to form PVC frame, complete as per specification and drawing. |
| 100 | M&L PCC 1:2:4 Type B0 using 12.5 mm graded crushed stone aggregate in roof padding, minimum consolidated thickness 25 mm as levelling course, laid and compacted to minimum slope 1:30, complete. |
| 101 | M&L factory-cast precast cement concrete kerb stone in PCC 1:2:4 Type B1 using 20 mm graded crushed stone aggregate, with plain/interlocking joints as directed, solid blocks exceeding 10 cm width, set and jointed in CM 1:6, complete. |
| 102 | Excavating in trenches not exceeding 1.5 metre wide and not exceeding 1.5 metre in depth for foundations or for shafts, walls, manholes, laying cables, pipes etc., not exceeding 10 Sqm on plan, and getting out in soft/loose soil, complete. |
| 103 | Returning, filling in, including spreading, levelling, watering and well ramming in layers not exceeding 25 cm thick in soft/loose soil, complete. |
| 104 | Removal of excavated soil/material to a distance not exceeding 50 metre and depositing where directed at a level not exceeding 1.50 metre above starting point, complete all as specified. |
| 105 | M&L cement concrete 1:4:8 Type D2 using 40 mm graded crushed stone aggregate in foundations, filling or mass concrete, complete. |
| 106 | M&L RCC nominal mix Type B1 (1:2:4) using 20 mm graded crushed stone aggregate in foundations including footings, plinth beams, bases for columns etc., complete all as specified and directed. |
| 107 | M&L RCC nominal mix Type B1 (1:2:4) using 20 mm graded crushed stone aggregate in columns, pillars, piers, posts and struts, complete all as specified and directed. |
| 108 | M&L RCC nominal mix Type B1 (1:2:4) using 20 mm graded crushed stone aggregate in beams, cantilevers, bressummers and lintels exceeding 1.50 m span, complete all as specified and directed. |
| 109 | M&L RCC nominal mix Type B1 (1:2:4) using 20 mm graded crushed stone aggregate in slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs, shelves and the like, complete all as specified and directed. |
| 110 | M&L RCC nominal mix Type B1 (1:2:4) using 20 mm graded crushed stone aggregate in chajjas and the like, complete all as specified and directed. |
| 111 | M&L TMT reinforcement bars 10 mm dia and over, cut to length and bent to required shape including cranking, spiral bending, hooking ends and binding with annealed MS wire not less than 0.90 mm dia or securing with clips, complete all as specified and directed. |
| 112 | All as per reinforcement item above but for bars 5 mm to 10 mm dia as in stirrups, spacers, binders etc., complete all as specified and directed. |
| 113 | M&L formwork to sides of concrete foundations, footings, bases of columns, rafts and raft beams and sides/soffits of foundation and plinth beams and similar work, vertical or battered, complete all as specified and directed. |
| 114 | M&L formwork to sides of pillars, posts, struts, piers and columns, complete all as specified and directed. |
| 115 | M&L formwork to sides and soffits of floor/roof beams, beam haunchings, girders, bressummers, lintels, cantilevers and shelves including supports, overhangs and splays between floors and beams, complete all as specified and directed. |
| 116 | M&L for treating the backfill in contact with foundations with approved anti-termite chemical emulsion at the rate of 7.5 litres per Sqm of vertical surface, the area of substructure in contact with backfill being measured, complete all as specified and directed. |
| 117 | M&L for treating the top surface of filled earth below floors with approved anti-termite chemical emulsion at the rate of 5 litres per Sqm of surface area, complete all as specified and directed. |
| 118 | M&L for treating the soil under plinth protection with approved anti-termite chemical emulsion at the rate of 5 litres per Sqm of surface area, complete all as specified and directed. |
| 119 | M&L rendering 15 mm thick in CM 1:6 on other than fair faces of brickwork, finished even and smooth without using extra cement, complete all as specified and directed. |
| 120 | M&L rough-cast plaster on exterior walls comprising undercoat of cement and sand mortar 1:3 not less than 10 mm thick and, while still plastic, applying rough-cast mixture of crushed stone/fine gravel aggregate 6 to 12 mm mixed with coarse sand and cement in ratio 1:1:1, finished even, complete all as specified and directed. |
| 121 | M&L for preparation of newly plastered wall surfaces and applying two coats of cement-base paint over one coat of primer, complete all as specified and directed. |
| 122 | M&L hardcore of broken boulders, gauge not exceeding 63 mm, complete all as specified and directed. |
| 123 | S&F stainless steel barrel tower bolt of extruded section, 150 mm long, fixed complete. |
| 124 | S&F stainless steel handle, 150 mm size, fabricated type, ISI marked, fixed complete. |
| 125 | S&F PTMT waste coupling, half/full threaded, minimum weight 60 grams for 40 mm size, complete. |
| 126 | S&F PVC (SWR) 110 mm branch piece, single Y, equal or unequal, complete. |
| 127 | M&L cutting into existing manholes for connecting new 150 mm drains, making good around pipe and rendering, cutting out existing benching and forming branch channel, half-round or three-quarter section, in CC 1:2:4 Type B1, smooth finished, and reforming benching as required, complete. |
| 128 | M&L concrete bed to drain pipe including packing under and haunching against sides of pipes after laying and testing, in PCC 1:3:6 Type C2, for 150 mm bore pipe, complete. |
| 129 | M&L reinforced concrete pipe, 150 mm bore, Class NP2, laid and jointed with collars, complete all as specified and directed. |
| 130 | M&L precast RCC 1:2:4 Type B1 using 20 mm graded crushed stone aggregate in manhole cover slabs of any thickness, size or shape, including necessary formwork, set and jointed in CM 1:4, complete. |
| 131 | S&F stack clamps for 100 mm dia pipe fabricated from 50 x 5 mm flat iron and 16 mm dia round-iron stays including nuts and bolts and securing ends of stays to wall/roof, complete. |
| 132 | Extra for forming fair-finished drain or channel up to 30 cm inner girth in cement concrete using extra cement including forms/moulds and mitred/stopped ends, complete. |
| 133 | M&L PCC 1:2:4 Type B0 using 20 mm graded crushed stone aggregate for manhole bedding and coping including necessary formwork, complete. |
| 134 | M&L hardcore of gauge not exceeding 63 mm, deposited, spread and levelled in layers not exceeding 15 cm thick, watered and rammed to a true surface, complete. |
| 135 | M&L PCC 1:3:6 Type C2 using 40 mm graded crushed stone stone aggregate in foundation filling/mass concrete as in post holes, complete. |
| 136 | M&L providing and laying at or near ground level factory-made kerb stone of M-25 grade cement concrete in position to required line, level and curvature, jointed in CM 1:3, including making joints with or without grooves and providing drainage openings wherever required, complete all as specified and directed. |
| 137 | Taking down carefully copper/aluminium point wiring (light, socket or power) complete, including fittings such as switches, ceiling roses, pendants, regulators, sockets etc. (to be measured separately), and making good disturbed surfaces of walls, floors etc. to match with existing surfaces. |
| 138 | Taking down MCB with sheet metal enclosure, main switch, DB etc. and making good disturbed surfaces to match with existing surfaces, complete. |
| 139 | Taking down carefully by unscrewing from boards/outlet boxes fittings and fixtures such as switches, sockets, ceiling roses, lamp holders, building security lights with brackets, ceiling fittings 2x2 LED, bulkhead fittings, tube light of any type, bed side lights, modular switch sockets, modular sheet metal flush boxes, fan regulators of any type etc., complete all as specified and directed. |
| 140 | M&L for concealed point wiring with two single core PVC insulated, unsheathed, multistranded copper conductor cables of size 1.5 Sqmm (FRLS), drawn in and including electrical grade PVC conduit 20 mm dia concealed on wall/ceiling/floor, including PVC insulated unsheathed earth wire with multistranded copper conductor of size 1.5 Sqmm (FRLS), including MS sheet metal box with modular sheet top cover of required module with frame for mounting switches, sockets etc., including cutting chases in stone/brick wall and making good disturbed surfaces including plastering and painting to match existing colour and including modular cover plates of required module with frame and sheet metal box, complete all as specified and directed: One light point controlled by one one-way switch. |
| 141 | All as per preceding concealed point wiring item but one ceiling/exhaust fan point controlled by one switch and regulator. |
| 142 | All as per preceding concealed point wiring item but one 3-pin 5 Amp switch socket outlet on the same board with other switches. |
| 143 | All as per preceding concealed point wiring item but one 3-pin 5 Amp switch socket outlet point on independent board. |
| 144 | All as per preceding concealed point wiring item but one bell/buzzer point controlled by one bell push. |
| 145 | All as per preceding concealed point wiring item but two-way point controlled by two-way switches. |
| 146 | All as per concealed point wiring item above but wiring with 4 Sqmm multistranded copper conductor cable and earth wire with copper conductor of size 4 Sqmm for 15 Amp power point, complete all as specified and directed. |
| 147 | Supply and fixing modular switch, piano type, 230/250 Volts, one-way 6 Amp, 1 module, graded on top cover, complete all as specified and directed. |
| 148 | Supply and fixing modular switch, piano type, 230/250 Volts, two-way 6 Amp, 1 module, graded on top cover, complete all as specified and directed. |
| 149 | Supply and fixing modular switch, piano type, 230/250 Volts, one-way 16 Amp, 1 module, graded on top cover, complete all as specified and directed. |
| 150 | Supply and fixing modular bell push, 6 Amp, 1 module, 230/250 Volts, complete all as specified and directed. |
| 151 | Supply and fixing multipurpose flush mounting modular socket outlet, 230/250 Volts, 2-in-1, 3-pin 5 Amp, 2 module, complete all as specified and directed. |
| 152 | Supply and fixing modular socket outlet, 2-in-1, 3-pin 15 Amp, flush type, 230/250 Volts, complete all as specified and directed. |
| 153 | S&F multi-music type AC 230 Volts, single pole, modular type, complete all as specified and directed. |
| 154 | S&F in repair modular fan regulator, 120W, 2 module, complete all as specified and directed. |
| 155 | Supply and fix LED batten 1.2 metre long made of CRCA sheet housing with PC glossy diffuser, having nominal system lumen output of 2000 lumens at minimum system efficacy of 115 lumen per watt and total power consumption not exceeding 20 Watt including driver, rated system life 40000 burning hours at L70, operating temperature 6500K, CRI >80, THD <10 and PF >0.95, complete all as specified and directed. Make: Crompton Cat Part CIS-305-40-57-SL-DP-NWH / Philips Cat Part BN300C LED20S-6500 L120 PSU WH / Havells Cat Part Stella 20 Watt / Galmtube LHEWA/JPGPV1D020 or equivalent approved make. |
| 156 | Supply and fix lamp holder with insulated body and back plate for angle/batten fitting with LED of 09 Watt, complete all as specified and directed. |
| 157 | Supply and fixing 20 Watt emergency LED inverter bulb B-22 type with inbuilt powerful lithium battery backup of at least 4 hours and minimum two years warranty, with deep discharge protection and fast charging, complete all as specified and directed. Make: Havells/Philips/Bajaj or equivalent approved make. |
| 158 | Supply and fixing in replacement LED bulkhead fitting 1x10 Watt complete with standard LED lighting fixture with extruded polycarbonate housing, including electrical connection using 2-core flexible copper conductor cable 23/0.0076 from ceiling rose to light fitting, complete with all accessories; luminaire efficacy minimum 100 lumen/Watt, input voltage 140-270 Volts, operating temperature -5°C to +50°C, PF minimum 0.95, THD <15%, IP-65, CCT minimum 5400K, polycarbonate housing white coloured, LED driver of same make with open/short circuit and over-voltage protection, surge protection minimum 2.5 kV, CRI minimum 80 and rated life 50000 burning hours at L70, complete all as specified and directed. |
| 159 | Supply and fixing in replacement LED light fitting for mirror, adjustable type, with high output diffuser, 2 feet long, 10 Watt, 220V AC decorative type, tricolour setting with driver holder and LED lamp including connection using 3-core flexible copper conductor cable of suitable size, complete all as specified and directed. |
| 160 | Supply and fix ceiling rose, surface bakelite, two to three terminals/plate, 5 Amps, complete. |
| 161 | Supply and fix sheet metal enclosure DB, single pole and neutral for 240 Volts, 8-way, with 200 Amp rated busbar, flush/surface mounting, double door including wooden board, complete all as specified and directed. |
| 162 | Supply and fix vertical MCB distribution box, 3-phase TPN, 4-way, double door, for mounting MCB/ELCB/isolators etc., factory made conforming to IS-13032, fabricated from CRCA sheet not less than 1.2 mm thick, fitted with DIN channel, neutral line and 200 Amp rated busbar, with sheet steel having undergone anti-rust treatment, double door type, DB and MCB/isolator of same make and labels for IP-42 protection, complete all as specified and directed. |
| 163 | Supply and fix in repair MCCB 100 Amp, 4-pole, 415 Volts, rupturing capacity 16 kA, fixed type in V TPN DB, complete all as specified and directed. |
| 164 | Supply and fix MCB, single pole, 240 Volts, 6-32 Amp, 10 kA, complete all as specified and directed. |
| 165 | Supply and fix MCB SPN, 240 Volts, 32 Amp, 10 kA, complete all as specified and directed. |
| 166 | S&F sub-main wiring on and including passing through PVC conduit concealed, including cutting chases in stone/brick wall, 1100 Volts grade, with PVC flexible cable copper conductor fire resistant low smoke and halogen (FRLSH), unsheathed multistranded single core of size 6 Sqmm and continuous earth with PVC flexible cable copper conductor, unsheathed multistranded single core of size 6 Sqmm, green colour, conforming to IS 694/1990, including taking down existing unserviceable sub-main wiring. Two runs of cable with one run of earth wire and one run of PVC conduit shall be measured as one length. |
| 167 | M&L for earthing complete with galvanised steel plate earth electrode 600 x 600 x 6 mm, buried vertically in ground with top edge of plate at a depth not less than 2.25 metre below normal ground level, connected to 4 mm dia GI earth wire by means of bolts, nuts, check nuts and washers, including chemical compound, 4 mm dia GI earth wire up to 7.50 metre length, 20 mm dia medium grade GI watering pipe with funnel and wire mesh, 40 mm dia GI protection pipe, earthing pit in PCC 1:2:4 Type B1 using 20 mm graded stone aggregate, RCC pit cover reinforced with 8 mm dia CTD bars @ 150 mm c/c both ways, including excavation, returning, filling and disposal of surplus soil, testing of earth electrode and all necessary connections, complete all as specified and directed. |
| 168 | S&F sheet metal enclosure, single pole and neutral, with 02-pin and earth plug and socket complete with 01 single pole 20 Amp, 240 Volts MCB, including necessary fixing arrangement and all incoming and outgoing electrical connections, complete all as specified and directed. |
| 169 | Supply and fixing in replacement energy efficient LED street light fitting of 45 Watt, pressure die-cast aluminium housing/body with heat resistant clear toughened glass and suitable optics for low distribution street/roadway luminaire, with driver, including electric connection, fixing light fitting with new GI tubing bracket made out of 32 mm dia light grade GI tubing 1.2 metre long bent at 120 degree angle at half metre from bottom, including two Nos clamps made out of MS flat iron 40x3 mm with suitable nuts and bolts and painting clamps/nuts/bolts with two coats aluminium paint over red oxide primer, including taking down old unserviceable light fitting with old bracket; luminaire efficacy minimum 100 lumen/Watt, input voltage 140-270 Volts, operating temperature -10°C to +50°C, PF minimum 0.95, THD maximum 10%, IP66, IK rating minimum IK07, built-in potted LED driver of same make with open/short circuit and over-voltage protection, surge protection 10 kV, CCT 5700K, CRI >80 and rated life 50000 burning hours at L70, complete all as specified and directed. Please Enable Macros to View BoQ information |
| 170 | Supply and fixing in replacement energy efficient LED street light fitting of 45 Watt, pressure die-cast aluminium housing/body with heat resistant clear toughened glass and suitable optics for low distribution street/roadway luminaire, with driver, including electric connection, fixing light fitting with new GI tubing bracket made out of 32 mm dia light grade GI tubing 1.2 metre long bent at 120 degree angle at half metre from bottom, including two Nos clamps made out of MS flat iron 40x3 mm with suitable nuts and bolts and painting clamps/nuts/bolts with two coats aluminium paint over red oxide primer, including taking down old unserviceable light fitting with old bracket; luminaire efficacy minimum 100 lumen/Watt, input voltage 140-270 Volts, operating temperature -10°C to +50°C, PF minimum 0.95, THD maximum 10%, IP66, IK rating minimum IK07, built-in potted LED driver of same make with open/short circuit and over-voltage protection, surge protection 10 kV, CCT 5700K, CRI >80 and rated life 50000 burning hours at L70, complete all as specified and directed. Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Sep 23, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedOct 15, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 16 daysOct 17, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 18 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender