Tender For Repair To Leakage/Seepage, Roof Treatment And Connected B/R Nature Wks In Did Line, Kabul Line, (Offrs), Capt Anuj Nayyar Road, Karam Vihar, Sumran Line, New More Line & Messes (Engrs, 1/5 Gr, Delhi Area) And Nc Hut And Otm Accn In The Are
Tender Value
1.48 Crore
Estimated cost
Bid Submission
20 Oct 2026
3 days left
EMD
2.23 Lakhs
Bank guarantee accepted
Document Fee
1000
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
New Delhi → Delhi
EMD Exemption
Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for Repair To Leakage/Seepage, Roof Treatment And Connected B/R Nature Wks In Did Line, Kabul Line, (Offrs), Capt Anuj Nayyar Road, Karam Vihar, Sumran Line, New More Line & Messes (Engrs, 1/5 Gr, Delhi Area) And Nc Hut And Otm Accn In The Area Of Age B/R-Ii Under Ge (East) Delhi Cantt-10
BOQ
| Sl. No. | Item Description |
| 1 | Dismantling of Brick tiles or terracing tiles, single layer on roofs. |
| 2 | S&F for Heat Resistant Terrace Tiles (300 mm x 300 mm x 20 mm) with SRI (solar refractive index) > 78, solar reflection > 0.70 and initial emittance > 0.75 on waterproof and sloped surface of terrace, laid on 20 mm thick cement sand mortar in the ratio of 1:4 (1 cement : 4 coarse sand) and grouting the joints with mix of white cement & marble powder in ratio of 1:1, including rubbing and polishing of the surface upto 3 cuts complete, including providing skirting upto 150 mm height along the parapet walls in the same manner. |
| 3 | M&L cleaning of plastered roof surface and applying one coat of cold bituminous primer @ 0.25 ltrs / sqm conforming to IS 3384-1986, A Layer of APP based polymeric membrane , 3 mm thick ( Minimum) weighing 3.5 kg/sqm reinforced with polyester non woven fabric ( weighing not less than 160 gms/sqm ) shall be applied over bituminous primer as specified above and application of polymeric membrane shall be by torch application, the over lap shall be minimium 100 mm on transverse direction and 75 mm on longitudinal direction and applying one coat aluminium paint over the APP membrane @ 0.11 kg/sqm , complete all as specified and as directed. |
| 4 | Demolition of Mud in roofs, any thickness, including plastering and leeping (whether full thickness removed or only a part thereof). |
| 5 | Cutting out cracks to V-section in existing roofs or terracing surfaces, cleaning out and filling solidly with a hot mixture of bitumen and clean dry sand 1:1 (by weight), complete all as specified and as directed. |
| 6 | Cutting chases, pinning in. making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc.; and cutting chases for inserting APP membrane, concealed water tubing or concealed conduit wiring, etc., and making good, cutting not exc 10 cm girth in brick wall. |
| 7 | M&L for providing cement concrete type 1:2:4 type B-0(12.5 mm graded agg ) as in roof kerbs or mud stops, filling of hold fasts and door frames, rounded or chamfered on edges complete all as specified. |
| 8 | M&L PCC 1:3:6 type C2 with 20 mm graded stone aggregate as in padding over roof slab for making slope on roof top surface finished even and smooth complete all as specified and directed. |
| 9 | M&L for 10 mm thick Cement plaster on surfaces of concrete in CM 1:4 on roof surfaces (Over PCC Padding) with WPC (WPC shall be measured and paid separately) |
| 10 | Supply only of liquid water proofing compound complete all as specified and directed. |
| 11 | Providing and applying Smartcare Dampproof, a fibre reinforced elastomeric liquid water proofing membrane formulated with reinforcing acrylic fibers having Sun Reflectivity Index (SRI) of 105 on horizontal/vertical surfaces of roof/wall/chajjas in multiple coats @2.0 litre/sqm. Primary coat is self-priming coat of elastomeric waterproofing liquid (dilution with water in the ratio of 3:1, damp proof : water) and other coats to be applied undiluted. The coating needs to be reinforced with 40 GSM geotextile, to sandwiched between 2nd & 3rd coat of coating. The application shall be carried out after scrapping and properly cleaning the surface to remove loose particles with wire brushes complete in all respect as per the direction of Engineer-in-Charge. Notes:(1) The work shall be executed through authorised applicator of manufacturer only.(2) Authrised Applicator shall be approved by GE before starting of work.(3) All materials shall be procured directly form manufacturer. (4) Guarantee: The contractor shall furnish a written guarantee for the effectiveness of the water proofing treatment for a period of Eight years in favour of the GE. A sum equivalent to 2.5% (Two point Five Percent) of the cost of water proofing treatment shall be retained by the Govt from the contractor’s dues as security deposit. The contractor may, however, furnish a fixed deposit receipt in lieu from a Schedule bank pledged in favour of Garrison Engineer. |
| 12 | Taking up or down steel tubing 15 mm bore and connection including cleaning for refixing or removal to store complete all as specified and as directed by Engineer-in-Charge |
| 13 | S&F steel tubing medium grade galvanised with all fittings and fixed complete to walls and ceiling or laid in floors, bore of pipe 15 mm dia including making hole in RCC slabs for vertical pipes & making good the same with Cement Concrete 1:2:4 complete all as specified and as directed by Engineer-in-Charge |
| 14 | Taking up or down steel tubing 20 mm bore and connection including cleaning for refixing or removal to store complete all as specified and as directed by Engineer-in-Charge |
| 15 | S&F steel tubing medium grade galvanised with all fittings and fixed complete to walls and ceiling or laid in floors, bore of pipe 20 mm dia including making hole in RCC slabs for vertical pipes & making good the same with Cement Concrete 1:2:4 complete all as specified and as directed by Engineer-in-Charge |
| 16 | Taking up or down steel tubing 25 mm bore and connection including cleaning for refixing or removal to store complete all as specified and as directed by Engineer-in-Charge |
| 17 | S&F steel tubing medium grade galvanised with all fittings and fixed complete to walls and ceiling or laid in floors, bore of pipe 25 mm dia including making hole in RCC slabs for vertical pipes & making good the same with Cement Concrete 1:2:4 complete all as specified and as directed by Engineer-in-Charge |
| 18 | S&F in repair 15mm Gun-metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed |
| 19 | S&F in repair 20mm Gun-metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed |
| 20 | S&F in repair 25mm Gun-metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed |
| 21 | Dismantling water tanks exc 250 Ltrs but not exc 500 ltr capacity and removing to store. |
| 22 | S&F rotational moulded polythylene water storage tanks 500 ltr capacity (cylindrical vertical with closed top ) hoisted and fixed in position complete with ball valve of high pressure of PTMT with epoxy coated aluminium rod and high density plastic ball and screwd for iron pipe 25mm bore complete all as specified and directed. |
| 23 | Dismantling water tanks exc 500 Ltrs but not exc 1000 ltr capacity and removing to store. |
| 24 | S&F rotational moulded polythylene water storage tanks 1000 ltr capacity (cylindrical vertical with closed top) hoisted and fixed in position complete with ball valve of high pressure of PTMT with epoxy coated aluminium rod and high density plastic ball and screwd for iron pipe 25mm bore complete all as specified and directed. |
| 25 | Dismantling wrought iron or mild steel work of any description not otherwise provided |
| 26 | S&F for Framed work as in doors or gates of angle or other section with gusset plates, rails, braces, etc., complete, drilled for fixing of steel sheeting or other covering. Doors, etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering, running rails and guides) and hanging; also fastening and fixing Fe 410-W (GdeE- 250) qualityAcomplete all as directed and specified. |
| 27 | M&L for preparing new Steel surfaces of any description over 10cm width or girth and applying two coats of synthetic enamalle paint over a coat of red oxide zink chrome primer. complete all as specified and as directed. |
| 28 | Demolition of reinforced cement concrete of any description and in any position not otherwise specifically provided for complete all as specifed and directed. |
| 29 | M&L for providing RCC 1:2:4 type B-1 using 20 mm grade stone aggregate as in slab supportetd on walls, shelves, Chajjas, cantilevers or similar work complete all as specified and as directed. |
| 30 | M&L for Formwork to Chajjas through and similar items including edges and similar work complete all as specified and as directed. |
| 31 | M&L TMT bars 10mm dia and over in reinforcement cut to length bent to shape required incl hooking ends and binding with MS wire (annealed) not less than 0.9mm dia complete all as directed and specified. |
| 32 | M&L TMT bars 5mm dia and over upto and including 10mm dia in stirrups, spacers and binders in reinforcement cut to length bent to shape required incl hooking ends and binding with MS wire (annealed) not less than 0.9mm dia complete all as directed and specified. |
| 33 | Demolition of brick work/stone bulder measonary built in cement mortar or cement lime mortar of any description and in any position all as specified. |
| 34 | M&L for brick work in CM (1:4) straight or curved on plan exc 6.0m mean radius and using old size sub class 'B' bricks all as specified. |
| 35 | S&F in repair CP Grating 125 mm dia with waste hole or without waste hole |
| 36 | S&F in repair PVC (SWR) floor trap, plain with grating (waste hole/plain type) including jointing with solvent cement, 75 to 100 mm mm diameter of outlet, all as specified. |
| 37 | Demolition and breaking up drain pipes (SGSW, AC, PVC or reinforced cement) set in cement mortor internal dia of pipe 100 mm complete all as specified and directed. |
| 38 | S&F of 110 mm bore SWR pipes single socketed in any length with rubber ring joints fixed to walls ,floors, trenches etccomplete all specified and directed. |
| 39 | All as per item No 38 above but 75 mm dia PVC SWR pipe. |
| 40 | S&F 110 mm bore PVC (SWR) bends with rubber ring joints fixed to walls complete all as specified and directed. |
| 41 | All as per item No 40 above but 75 mm dia PVC SWR bends. |
| 42 | Taking down cement or lime plaster any description on brick or stone walls etc including racking out joints hacking for key scrubbing down with waters etc. |
| 43 | M&L for rendering 15 mm thick in cement mortor 1:4 on brick/ concrete surfaces with water proofing compound and finishing the surface even and fair without using extra cement complete all as specified directed. Note :- The work shall be executed up to G+8th floor Height |
| 44 | M&L for rendering 15mm thick cement plaster in cement mortar (1:6) finished even & smooth without using extra cement on brick/concrete surfaces complete all specified and directed. |
| 45 | M&L for preparing New plasteres surfaces Wall and applying of Birla/JK white wall care putty approx 2 mm thick on Wall as per manufacturer's instruction on existing prepared surface and make the surface smooth by rubbing with sand papers etc and applying two coats of oil emulsion distemper over a coat of primer paint on interior Wall complete all as specified and directed. |
| 46 | M&L for prepration of newly plastered surfaces of wall and applying two coats of cement base paint over a coat of Primer complete all as specified and directed . |
| 47 | Complete removal of existing treatment of old surface of wall and applying 1mm thick putty again sanding and appying two coats of acrylic emulsion paint interior grade over primer complete all as specified and directed by Engineer-in-Charge. |
| 48 | Complete removal of existing treatment of old surface and applying two coats of oil bound distemper on wall surfaces complete all as specified and directed.(Note : Finishing coat to be applied with roller). |
| 49 | M&L for preparation old decorated external wall surface and applying one coats of Cement base paint complete all as specified and directed by Engr-in-charge. |
| 50 | Complete removal of existing treatment of old surface and applying two coats of weather proofing exterior acrylic emulsion paint premium quality on wall surfaces over one coat of primer from the same manufacturer complete all as specified and directed. |
| 51 | Dismantling AC Sheets/CGI Sheets corrugated in roof coverings including ridges all as specified and directed |
| 52 | S & F Pre painted coloured galvalume aluminium Zink coating GI based corrugated steel sheet 0.50 mm thick of an colour having tensile strength of 550 Mpa as in roof covering / Cladding to wall, fixed with self tapping screws as specified. |
| 53 | S&F Pre-painted galvalume aluminum zinc coating GI based Plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in ridges, hips, valley gutters & fixed with self tapping screws as specified. |
| 54 | Dismantling wall and ceililing boards (fibre, pulp, insulation etc. ) or insulation boards/ slabs/ blankets, any thickness, including cover fiilets complete all as specified and directed. |
| 55 | M&L for aluminium anodised snap grid frame work of size 605 x 605mm for false ceiling with hanging arrangement of 6mm dia G.I.( upto 1200 mm length ) adjusting level fixed to roof slab by means of ceiling cleats made out of GI flat 40x3 mm size and 60mm long and expension hold fastners 12.50mm dia 40mm long complete all as specified and directed. |
| 56 | M&L for Non asbestos 4mm thick fibre cement building boards fixed or laid / inserted to aluminium frame work with screws as in false ceiling fixed in ceiling flat or sloping complete all as specified and directed. |
| 57 | M&L for Providing and fixing 10mm thick plaster of paris ceiling (Gypsum anhydrous) to flat surface over 2nd class soft wood fillets, or metal frame work and reinforced with G.I. wire mesh (Fillets, metal frame work paid separately) |
| 58 | S&F for 2mm thick fibre glass reinforced translucent plain sheeting fixed with coach screw and washer in roof, wall etc. including dismantling of old sheet complete all as specified. Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Sep 22, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedOct 20, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 3 daysOct 21, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 4 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender