Tender For Repair And Replacemet Of Joinery And Miscellaneous Work At Pao (Or), special Repair To Security Fencing Near Bldg No 16 To Postmartem Area, special Repair /Replacemtn Of Gi Pipe Line At Jco Mess To Md Accn Near Vijay Park At Rts (D) Sahara
Tender Value
Ref. Documents
Estimated cost
Bid Submission
13 Oct 2026
17 days left
EMD
97420
Bank guarantee accepted
Document Fee
500
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Haridwar → Uttarakhand
EMD Exemption
Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for Repair And Replacemet Of Joinery And Miscellaneous Work At Pao (Or), special Repair To Security Fencing Near Bldg No 16 To Postmartem Area, special Repair /Replacemtn Of Gi Pipe Line At Jco Mess To Md Accn Near Vijay Park At Rts (D) Saharanpur And Certain Rev And Minor Works At Roorkee And Saharanpur Under Ge Roorkee
BOQ
| Sl. No. | Item Description |
| 1 | Demolition of cement concrete in ground floor & paving, n. exc 15 cm thick (below or above GL), unreinforced complete all as specified and directed and removing debris outside MoD land complete all as specified and as directed by Engr-in-Charge |
| 2 | M&L 40mm thick cement concrete (1:2:4), type B1 (using 20 mm graded stone aggregate) as in floor finished even and smooth without using extra cement complete all as specified and directed. |
| 3 | M&L cement concrete (1:4:8), type D2 (using 40 mm graded stone aggregate) as in subbase complete all as specified and directed. |
| 4 | M&L for 75mm thick cement concrete (1:3:6) type C2, using 40mm graded stone aggregate as in plinth protection and finishing the surfaces even and smooth without using extra cement, including necessary expansion joints, filled solidly with a hot mixture of blown grade bitumen and sand 1:1 by weight complete all as specified and directed. |
| 5 | M&L for PCC (1:2:4), type B-1 (20 mm graded stone aggregate) as in coping, DPC, embedding hold fast, etc. complete all as specified and directed. |
| 6 | M&L for RCC (1:2:4), Type B1 (20 mm graded stone aggregate) as in beams, cantilevers, chajjas, lintels over 1.5 m span complete all as specified and directed. |
| 7 | M&L for precast reinforced cement concrete type B-1 (1:2:4) in landings, cover slabs for manholes, kitchen platform etc and similar articles with plain faces, with plain fair faces, including chamfers, weathering, throating etc and setting in mortar complete with joints to match set in CM 1:6 complete all as specified and directed. |
| 8 | M&L for providing reinforced cement concrete (1:2:4), type B-1 using 20 mm graded crushed stone aggregate as in slabs supported on walls, beams and columns in floors, roof landings, kitchen shelves, landing or in any position complete all as specified and directed. |
| 9 | M&L for RCC, M-20 (Design Mix) (using 20mm graded granite stone aggregates) as in Slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like complete all as specified and directed. |
| 10 | Formwork for rough finished surfaces to chajjas and similar works complete all as specified and directed. |
| 11 | Formwork for rough finished surfaces to soffits of suspended slabs such as roof slab, floor slabs, landings and similar work etc not exc 200 mm thickness (horizontal or sloping) complete all as specified and directed. |
| 12 | Formwork for fair finished surfaces to soffits of suspended slabs such as roof slab, floor slabs, landings and similar work etc not exc 200 mm thickness (horizontal or sloping) complete all as specified and directed. |
| 13 | Formwork for rough finished surfaces to edges of concrete flats, RCC/PCC bands, etc exc 10 cm but not exc 20 cm wide complete all as specified and directed. |
| 14 | M&L for 60 mm thick Machine pressed precast conctete interlocking paver block any shape and size confirming to IS 15658-2006 of M-35 Grade made with grey cement and pigment complete all as specified and directed |
| 15 | Supply and laying sand (25 mm thickness) for cushioning to interlocking paver block complete all as specified and directed. |
| 16 | Demolition of brick work or stone/boulder masonry, built in cement mortar or cement lime mortar including all quoins, arches, pillars etc but excluding ashlar facing dressed stone work and precast concrete articles and removing debris out side MoD land complete all as specified and directed. |
| 17 | M&L for Brickwork with sub class ‘B’ bricks, (Old size bricks), straight or curved on plan to any radius in half brick thick walls built in CM 1:4 complete all as specified and directed. |
| 18 | M&L for Brick work with sub class 'B' bricks, (Old size bricks), straight or curved on plan, exc 6 mtr mean radius, built in CM 1:6 complete all as specified and directed. |
| 19 | M&L for brick work built in CM (1:4) curved on plan n ecx 6 metre mean radius using sub class ‘B’ bricks (Old size bricks) in any thick honey comb work complete all as specified and as directed. (These item measured half qty of total measured qty) |
| 20 | Demolition of cement concrete (reinforced) of any position not otherwise specifically provided for and including reinforcement required to facilitate demolition upto and including fourth story and on the roof top/mumty/parapet and removal of debris and rubbish out side MoD land complete all as specified and directed. |
| 21 | M&L for mild steel TMT bars 10 mm dia and over, cut to length, bent to shape required, including hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia or securing with clips and including welding (if required) has to be done with minimum 20 cm over lap for new and Old unserviceable of any height complete all as specified and directed. |
| 22 | Ditto all as per above but for 6 to 8 mm dia bar as in stirupps etc. |
| 23 | M&L for mild steel TMT bars 5 mm dia and over upto and incl 10mm dia, cut to length, bent to shape required, as in stirrups, binders and spacers and binding with and including mild steel wire (annealed) not less than 0.9 mm dia or securing with clips complete all as specified and as directed. |
| 24 | Taking down cement plaster of any description from brick wall surfaces etc including racking out joints and hacking for key, scrubbing down with water etc including all necessary scaffolding arrangments of any height complete all as specified and directed. |
| 25 | M&L Rendering 12 mm thick in cement mortar 1:6 on fair face of brick work/ concrete surfaces (either surfaces) of wall and finished even and smooth without using extra cement complete all as specified and directed. |
| 26 | M&L Rendering 10 mm thick in cement mortar 1:6 on fair face of brick work/concrete surfaces (either surfaces) of wall and finished even and smooth without using extra cement complete all as specified and directed. |
| 27 | M&L for rendering 15mm thick consist of two coats top layer 5 mm thick in CM 1:4 (mixed with WPC) over 10 mm th in CM 1:6, on fair faces of brick work finished even & fair complete all as specified and directed. Note : WPC shall be meausured & paid separately. |
| 28 | M&L for Rendering 10mm thick in CM 1:4 on concrete surfaces in ceiling complete all as specified and directed. |
| 29 | M&L Rendering 15 mm thick on concrete/stone masonry surfaces to be finished even and smooth (without using extra cement) in CM 1:4 complete all as specified and directed. |
| 30 | M&L for rendering 15mm thick in CM 1:6 on stone masonry surfaces complete all as specified and directed. |
| 31 | M&L for Rendering 5mm thick in cm 1:3 on concrete surfaces in ceiling complete all as specified and as directed. |
| 32 | M&L rendering/ screed bed or bedding layer of mortar 15mm thick in CM 1:4 mixed with WPC on concrete surfaces as in floor finishes on roof top finished even & smooth without using extra cement. Note : WPC shall be meausured & paid separately. |
| 33 | M&L for roof treatment with polymeric membrance (APP based) with non woven polyster mat as reinforcement with following:-(a) M&L for surface preparation by removal of existing treatment of tar felt/PCC/plastering/tiling/loose particle to ensure or clean smooth and dry surrfaceand preparing the surface.(b) M&L for providing & laying a coat of cold applied bitumen 85/25 based primer on entire surface @ 0.30 Ltr/Sqm on dry and clean surface.(c) M&L for providing & laying APP based polymeric membrane of 3 mm thickness of weight of 3.0 Kg/Sqm with non wovenpolyster fibre as reinforcement on primed surface by torch application with side over laps & joints over laps etc as per manufacturers instruction.(d) M&L for finishing of top surface by two coat of aluminium paint over a coat of blown bitumen 85/25 grade @ 1.2 Kg/ Sqm grouted all as specified and as per manufacturers instruction. |
| 34 | M&L for complete removal of existing treatment on surfaces of walls and applying one coat of wall primer (water thinnable/ solvent thinnable), 2mm wall care putty for making the surface smooth, one coat of wall primer and applying two coats of tractor emulsion oil emulsion distemper to be applied by approved applicator of the manufacturer of the paint and all as specified and as approved all as specified and directed. |
| 35 | Supply only liquid water proofing compound complete all as specified and as directed. |
| 36 | M&L preparation of newly plastered surfaces of walls and applying three coats of white wash complete all as specified and as directed. |
| 37 | M&L for preparation of newly concrete/plastered surfaces of ceiling and applying three coats of white wash complete all as specified and as directed. |
| 38 | M&L for preparation of new surfaces of walls by sanding the surfaces and applying one coat of wall primer (water thinable/ solvent thinable), 2mm wall putty for making the surface smooth and even one coat of wall primer and applying two coats of tractor emulsion oil emulsion distemper to be applied by approved applicator of the manufacturer of the paint and all as specified and as approved all as specified and as directed. |
| 39 | M&L for complete removal of existing treatment on external walls and applying Two coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/10 over 1mm thik external wall putty complete all as specified and directed. |
| 40 | M&L for preparation of newly plastered external walls and applying Two coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 5489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/10 over 1mm thick external wall putty complete all as specified and directed. |
| 41 | M&L preparation new steel surface over 10 cm width or girth and applying two coat of synthetic enamel paint over a coat of red oxide primer complete all as specified and directed. |
| 42 | Dismantling floor hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish out side MoD land complete all as specified and directed. |
| 43 | M&L for non skid coloured ceramic tiles, joint free, conforming to IS-13755, group B-II(b), 1st & premium quality, Digital coloured ceramic tiles, exc 0.06 sqm but not exceeding 0.11 sqm x 6-7 mm thick in floors, shelves etc, set and jointed in neat cement slurry and pointed in coloured cement to match over and including screed bed of 15mm thick in CM (1:6) complete all as specified and as directed. |
| 44 | M&L for glazed coloured ceramic tiles conforming to IS-13755, group B III, 1st & premium quality, Digital coloured ceramic tiles, 600mm x 300mm or 450x300x7mm 350x250x7mm thick in vertical surfaces (including designed borders ) such as skirting and dados, set and jointed in neat cement slurry pointed in coloured cement to match over rendering 10 mm thick on fair faces of brick work in CM (1:4) complete all as specified and as directed. |
| 45 | S&F Vitrified tiles 8 to10 mm thick (square/rectangular light shade) polished, area of each tiles not exceeding 0.36 sqm, in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement over and including 15mm thick screed bed in cement mortar 1:6 complete all as specified and directed. |
| 46 | Demolition of stone slabs and tiles of any description or thickness laid in floors, aprons etc, laid, bedded and pointed in any mortar and and removing the rubbish outside MoD land complete all as specified and directed. |
| 47 | M&L for Granite (of any type and colour), 20mm thick machine cut, set, bedded and jointed with grey cement slurry and pointed with white cement with admixture of pigment to match the shade of granite stone including grinding and polishing complete including screed bed in cement plaster 20 mm thick 1:4, as in kitchen platform, jamb/cill of window, ventilator, border, flooring and simillar work etc complete all as specified and directed. |
| 48 | M&L for granite (of any type and colour) 14-16 mm thick (table rubbed and polished) in cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite incl moulding of front side if required complete all as specified and directed. |
| 49 | M&L for 18 to 20mm thick Udaipur Black Stone factory made bull nosed, polished (table rubbed and polished) as in jambs, window cills, cooking platform and the like etc over 10mm thick cement screed in CM 1:4 including pointing in white cement (1:2) using marble dust and admixture of pigment to match with shade of stone including rubbing and polishing including rounding of edges, making hole for gas pipe complete all as specified and directed. |
| 50 | Taking up or down 15 mm bore GI tubing and connections including cleaning for re-fixing complete all as specified and directed. |
| 51 | S&F steel water tubing of size 15mm bore, medium grade, galvanised iron with all fittings such as Tees, elbows, sockets, bends, unions, shortpieces, nipples, brass nuts and diminishing pieces complete all as per IS 1239, fixed to wall and ceiling or laid in floors and making good disturbed surfaces to match the existing surfaces complete all as specified and directed. |
| 52 | Taking up or down 20 mm bore GI tubing and connections including cleaning for re-fixing complete all as specified and directed. |
| 53 | S&F steel water tubing of size 20 mm bore, medium grade, galvanised iron with all Fittings such as Tees, elbows, sockets, bends, unions, shortpieces, nipples, brass nuts and diminishing pieces complete all as per IS 1239, fixed to wall and ceiling or laid in floors and making good disturbed surfaces to match the existing surfaces complete all as specified and directed. |
| 54 | S&F 20mm bore CPVC medium grade with all fittings and fixed to wall and ceiling or laid in floors etc complete all as specified and directed. |
| 55 | Cutting chases, pinning in making good to facing on brick walls where required and pointing in cement mortar (1:3) to ends for concealed water tubing and making good, cutting n, exc.10cm girth complete all as specified and as directed. |
| 56 | S&F in repairs vitreous china wash down, white, water closet pan (pedestal pattern) with 'P' of 'S' trap (of size 465mm x 355mm x 265mm), including plastic seat cover to match with colour of WC, closed pattern with flat bottom & cover and chromium plated mild steel or aluminium anodized hinging device including connecting to trap and flushing pipe, anti-syphonage pipe etc and screwed with brass screws to sheesham wood plugs embedded in floor complete all as specified and directed. |
| 57 | S&F in repairs vitreous china premium/1st quality wash down water closet EWC white/ivory/off white (closed pattern incl all necessary accessories like rag bolts/gel gasket etc.(excluding flushing cistern & flush pipe) complete in all respect all as specified. |
| 58 | S&F in repair wash hand basin table top of size Table Top Basin 565x425x140 vitrous China including, waste coupling & PVC waste pipe of 32 mm dia etc complete all as specified and directed. |
| 59 | S&F in repairs, vitreous china coloured wash basin with counter and pedestal, size 865x500mm excluding taps, waste, chain and plug and porcelain stopper but incl brackets and cutting for pinning in ends of bracket, complete all as specified and directed. |
| 60 | M&L for PVC connections 15mm size with PTMT nuts of length 450mm complete all as specified and directed. |
| 61 | S&F in repair PVC connection 15 mm bore and 45cm long with washers complete all as specified and directed. |
| 62 | S & F in repair 15 mm bore Single lever basin mixer extended body without pop-up waste system with 450 mm long flexible hose screwed down, fancy type high pressure, with or without lettered 'HOT or Cold unserviceable' with long screwed sunk and fly nuts complete all as specified and directed. |
| 63 | S&F in repairs 10 litres capacity, premium Push Button Type Flushing Cistern Dual 10 LTR Cistern low level slim, syphonic type, white, plastic flushing cistern as per IS 7231:1994 with inlet, ball valve float vavle and other connected accesories including brackets and 40 mm nominal dia high density polyethylene pipes for flush pipe complete all as specified and directed. |
| 64 | M&L for vitreous China squatting pan, ‘Orissa’ pattern, size 580x440 mm white, with integral foot rests (excluding flushing cistern and flush pipe) complete all as specified and directed. |
| 65 | S&F vitreous china wash down water closet pan (Pedestal pattern) white incl 'P' or 'S' trap (Make : Parryware/Hindware) and making good the disturbed surface to match with the existing complete all as specified and directed. |
| 66 | S&F WC plastic water closet (EWC) seat cover white closed pattern with flat bottom and cover incl mild steel chromium plated hinging device complete all as specified and directed. |
| 67 | S&F Health Faucet 8 mm dia 1.2 mtr long flexible tube & wall hook complete all as specified and directed. |
| 68 | S&F brass chromium plated bib tap (short body) for iron pipe of 15 mm bore fancy type with crutch or butterfly handle, screwed down high pressure complete all as specified and directed. |
| 69 | S&F stop/Angle cock ISI marked fancy type, chromium plated, screw down high pressure with crutch or butterfly handle screwed both ends suitable for iron pipe of 15 mm bore complete all as specified and directed. |
| 70 | S&F 15 mm bore stop valves, cast copper alloy, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe and fixed complete all as specified and directed. |
| 71 | S&F Pillar Cock 15mm catalog ORP-10001PM and complete all as specified and directed. |
| 72 | S&F of CP Towel Ring fixed with and including Chromium plated brass screws and wooden/plastic cleats complete all as specified and directed. |
| 73 | S&F Liquid soap container of PTMT fixed with and including Chromium plated brass screws and wooden/plastic cleats. (Minimum weight 105gms) complete all as specified and directed. |
| 74 | S&F Toilet paper holder with flat recessed type stainless steel \\"but of brass, chromium plated or stainless steel complete all as specified and directed. |
| 75 | S&F table top basin WHB (size 425x340x175 mm as per catalog CNS-WHT-903 and complete all as specified and directed. |
| 76 | S&F urinal (size 355x340x535 mm as per catalog URS-WHT-13261 and complete all as specified and directed. |
| 77 | S&F in repair 15 mm bore, fancy type, angular valve, cast copper alloy, screwed down, high pressure, with crutch or butter fly handle, screwed both ends for iron pipe or for unions complete all as specified and directed. |
| 78 | S&F in repair 15 mm bore, fancy type, bib taps, long body (two in one) cast copper alloy 15mm bore with fancy chromium plated screwed down, screwed for iron pipe or for brass ferrule complete all as specified and directed. |
| 79 | S&F in repair bib taps brass chromium plated 15 mm bore size screwed down screwed for iron pipe or for brass ferrule complete all as specified and directed. |
| 80 | S&F in repair 15 mm bore, fancy type, health faucet with SS hose complete all as specified and directed. |
| 81 | S&F in repair CP Towel Ring complete all as specified and directed. |
| 82 | S&F in repair Stainless steel chromium plated Soap dish, any type, fixed to plugs with chromium plated brass screws complete all as specified and directed. |
| 83 | S&F in repairs sheet glass corner shelf assembly consisting of 5.5 mm thick sheet galss shelf 12 cm wide with chromium plated bracket guard and railing 60 cm long complete all as specified and directed. |
| 84 | S&F 15 mm bore overhead shower 250 mm dia single flow (ABS body chrome plated with grey face plate) with rubit cleaning system including shower arm 381 mm long (cat part No-SA 106/108 of ESS ESS Croma) Square shape with wall flange complete all as specified and as directed. |
| 85 | S&F in repairs for stainless steel Robe hook 2-way thick complete all as specifed. Make:- ESS ESS CROMA Cat Part No AC-105 or Equivalent of JAQUAR/PARKO. |
| 86 | S&F in repair 75 mm dia PVC(SWR) multi floor trap with grating including jointing with solvent cement complete all as specified and as directed. |
| 87 | S&F in repair in brass chromium plated towel rack with 3 hooks complete all as specified. Make:- ESS ESS CROMA Cat Part No AC-208 or Equivalent of JAQUAR/PARKO. |
| 88 | S&F in repairs 5.50 mm thick of size 900X600 mm, bevelled edge mirror of selected quality glass and fixed to walls using hidden studs complete all as specified and directed. |
| 89 | S&F in repair Looking mirror 600x450 mm beveled edge 5.5 mm thick selected quality glass, mounted on 6 mm thick commercial ply, aluminium frame around and fixed to wooden plug with CP brass screws and cup washers complete all as specified and directed. |
| 90 | Taking down Chowkhats or frames n.exc 1.50 sqm each (without taking off shutters from the frames) complete all as specified and directed. |
| 91 | Taking down Chowkhats or frames, exc 1.50 sqm but n exc 4.00 sqm each (without taking off shutters from the frames) complete all as specified and directed. |
| 92 | S&F factory made single extruded WPC (Wood Polymer Composite) solid door Frames/Chowkhat comprising of 100 mm X 50 mm size, applying PVC solvent cement and screwed with full body threaded, star headed SS screws having minimum frame density of 750 kg/cum and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixed in position with MS hold unserviceable fast/lugs/SS dash fasteners of required dia and length complete all as specified and directed. |
| 93 | Ditto all as above but for 45x70mm size |
| 94 | S&F Solid PVC Door Frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with MS Square tube, suppling & fixing in opening as per specification & drawing complete all as specified and directed. |
| 95 | S&F Factory made solid panel PVC door shutter 30mm thick (style) consisting of frame made out of MS tubes for top & bottom rails, MS frame shall be covered with heat moulded plain colour PVC 'C' chanel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; panelling of plain colour PVC sheet to be fitted in the MS frame welded/sealed to the stiles & rails eith suitable PVC sheet beading, and joined together with solvent cement, supplying & fixing in the frame at site as per specification & drawing complete all as specified and directed. |
| 96 | All as per item No 95 here-in-before but fully glazed i.e glass panes used instead of 5mm PVC sheets panels for vent etc complete all as specified and directed. |
| 97 | S&F factory made 28-30 mm thick single extruded WPC (Wood Polymer Composite) solid plain flush door shutter of required size, modulus of elasticity 850 N/mm” and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk SS screws complete all as specified and as directed by Engr-in-Charge. |
| 98 | S&F FRP door frames three legged of cross section 90x45mm having single rebate 32mmx15mm. The laminated door frame moulded with fire retardant grade unsaturated polyester resin and chopped mat. Door frame laminated shall be 2mm thick, frame shall be covered with fiber glass from all sides MS flat iron 25x3mm shall be provided at the bottom to steady the frame including PCC 1:2:4 Ty B0 using 12.5mm graded stone aggregate as in frame, complete all as specified and directed. |
| 99 | S&F Fiber glass reinforced plastic (FRP) Flush door in different plain and wood finish made with fire retardant grade unsaturated polyester resin, moulded to 3 mm thick FRP laminate all around, with suitable wooden blocks inside at required places for fixing of fittings and polyurethane foam (PUF) polystyrene foam to be used as filler material throughout the hollow panel, casted monolithically with testing parameter of FRP, laminate confirming to table 3 of IS-14856 Complete all as specified by the manufacturer and as per direction of Engineer-in-charge. |
| 100 | S&F 200 mm length Stainless steel barrel tower bolt extruded section complete all as specified and directed. |
| 101 | S&F Stainless steel of grade barrel tower bolt 100 mm long, extruded section complete all as specified and directed. |
| 102 | S&F 150 mm size stainless steel bright finish handles for shutter complete all as specified & directed. |
| 103 | S&F 300mm long Stainless steel, anodised sliding door bolt with haps, staple (bolt type) and fixing clip of sheet, cast or extruded section and fixing bolts and sliding bolts of extruded section or cast aluminium alloy complete all as specified and directed. |
| 104 | S&F stainless steel butt hinges, heavy duty of 100mm size complete all as specified and as directed by Engr-in-Charge. |
| 105 | S&F Stainless steel alloy hasps and staples, type-1, safety type, size 100 mm, anodized finish, not be less than Grade AC 10 of IS 1868:1996 including fixing with screws complete all as specified and directed by Engr-in-charge. |
| 106 | S&F floor door stopper overall length of cover plate 140mm long of aluminium alloy body and tongue, anodised, with hard drawn steel spring, fixed in floor complete all as specified and as directed. |
| 107 | M&L Door closer hydraulically made of Cast iron body regulated, designation No. 3, universal type, suitable for door shutters of 851 to 1000 mm in width and of weight between 61 to 80 kg and fixed complete all as specified and directed. |
| 108 | S&F PTMT But hinges 100 mm complete all as specified and directed. |
| 109 | S&F PTMT Tower bolt 200 mm complete all as specified and directed. |
| 110 | S&F PTMT door handles 125mm complete all as specified and directed. |
| 111 | S&F PVC Pipe (SWR) 75mm laid in floors or trenches, fixed to walls, etc complete all as specified and directed. |
| 112 | S&F PVC Pipe (SWR) 110mm laid in floors or trenches, fixed to walls, etc complete all as specified and directed. |
| 113 | S&F floor trap of PVC 75 mm out let dia with grating and jointed to waste pipe complete all as specified and directed. |
| 114 | S&F in repair Grating square fitting of size 150mm made in two parts for smell and mosquito proofing with minimum 25 mm water seal of PTMT. (Minimum weight 85gms) complete all as specified and directed. |
| 115 | M&L in repair PVC (SWR) Gully trap 125/110mm setting and jointing with solvent cement complete all as specified and directed. |
| 116 | S&F sheet glass frosted 5.5 mm thick,one side frosted, and glazing in square exceeding 0.5 Sqm in each pane complete all as specified and as directed. |
| 117 | S&F stainless steel wire cloth 0.36 mm nominal dia of wire and average width of aperture 1.4 mm and fixed with stainless steel wire staples complete all as specified and as directed. |
| 118 | S&F in repairs 110 mm dia PVC (SWR) pipes, type B, single socketed in any length with rubber ring joints, sealed with adhesive suitable for PVC pipes and fixed to walls including stack clamps out of 50 mm x 5 mm flat iron and 16 mm dia round iron stays upto 04 storeys including all steel scaffloding arrangments complete all as specified and directed by Engr-in-charge. |
| 119 | Ditto all as above but 75mm dia size |
| 120 | S&F 75mm dia PVC (SWR) bends with access doors, any radius, at any height including steel scaffold unserviceable complete all as specified and directed by Engr-in-charge. |
| 121 | S&F 110mm dia PVC (SWR) bends with access doors, any radius, at any height including steel scaffold unserviceable complete all as specified and directed by Engr-in-charge. |
| 122 | S&F 75 mm dia PVC (SWR) junction single, (single T) equal or uequal, with access door at any height including steel scaffold unserviceable complete all as specified and directed by Engr-in-charge. |
| 123 | S&F 110 mm dia PVC (SWR) junction single, (single T) equal or uequal, with access door at any height including steel scaffold unserviceableing complete all as specified and directed by Engr-in-charge. |
| 124 | S&F 75 mm dia PVC (SWR) vent cowl, at any height including steel scaffold unserviceable complete all as specified and directed by Engr-in-charge. |
| 125 | Dismantling of water tanks 1000 ltr of capacity and removing to store complete all as specified and directed. |
| 126 | M&L 1000 ltrs Rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top) incl 20mm PTMT ball valve and sockets hoisted and fixed in position all as specified in SSR Part I. |
| 127 | Dismantling posts or struts (steel or RCC or wooden) any section including taking out embedded portion (concrete work) and making good disturbed ground complete all as specified and directed |
| 128 | Dismantling wrought iron or mild steel work of any description not otherwise provided all as specified and directed |
| 129 | S&F joist, channel, angle, tee sections,tubular hollow pipes, staging for water tank, purlin and eafter & MS flats fixed independently, without connection plate, etc and all other similar works conforming to Fe 410-W (Gde-E-250) quality- complete all as specified and directed by Engr-in-charge |
| 130 | S&F MS work as in hold fasts, bands supports, clamps, wall ties hooks incl nut and bolts etc conforming to Fe-290 Gde-E-165 including welding etc. all as specified. |
| 131 | M&L MS Steel work in tubular trusses/purline/column/nut bolts/ base plate including special shaped washer etc. complete using ERW or induction butt welded tubes conforming to IS1161-1979 grade St.-240. |
| 132 | M&L MS works as in Posts and struts in fencing including cutting tops to shape as directed, drilling holes, notching for wire etc; flat iron fillets for securing wire mesh etc) including all necessary drilling bolting or riveting etc and similar work confirming to Fe 290 Gde E-165; complete all as specified & as directed. |
| 133 | Fixing only New/Old chain link fencing including line wires, any mesh, size and type to any type of standards, rails, straining bolts etc including provision of binding wire complete all as specified & as directed. |
| 134 | Supply only chain link MS Galvanised fencing, any size or type complete all as specified & as directed. |
| 135 | S&F Mild & steel screw bolts (machine made) with hexagonal or square heads at one end and screwed the other, or screwed both ends, each screwed end to be fitted with washers and one hexagonal or square nut,n.exc. 5 cm and 5 to 10 mm dia complete all as specified & as directed. |
| 136 | S&F Galvanised. 2 strand, steel barbed wire 2.24mm dia barbed with 2mm dia barbs at 75mm spacings and straining and fixing to any type of standard rails strain- ing bolts, including, securing or tying at crossings with and provision of galvanised mild steel wire, staples or steel pins, etc. as directed (each line wire to be measured) complete all as specified and directed |
| 137 | Clearing of Vegetation along Fencing alignment including cutting and removal of grass, bushes and shrubs including small plants upto 30mm girth (Excluding big trees), uprooting of roots, dressing and levelling of ground in a uniform strip of 1.50 metre width, and disposal of unserviceable material outside site upto 50 metre lead, complete all as specified and directed by Engr-in-Charge. |
| 138 | S&F for Providing Powder coated aluminium (minimum thickness of powder coating 50 micron) work for doors, windows, ventilators and partitions (Fixed portions) with extruded built up standard tubular sections/appropriate Z sections and other sections of approved make conforming to IS:733 and IS:1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing/paneling, CP brass/stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-Charge. |
| 139 | S&F for providing and fixing Powder coated aluminium (minimum thickness of powder coating 50 micron) for shutters of doors, windows & ventilators including providing and fixing hinges/pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber/ neoprene gasket required (Fittings shall be paid for separately) with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS:733 and IS:1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e at top, bottom and sides with required EPDM rubber/neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing/paneling, CP brass/stainless steel screws all complete as per architectural drawings and the directions of Engineer-in-Charge. |
| 140 | S&F anodised aluminium grill (anodised transparent or dyed to required shade according to IS:1868 with minimum anodic coating of grade AC 15) of approved design/pattern, with approved standard section and fixed to the existing window frame with CP brass/stainless steel screws @ 200 mm centre to centre, including cutting the grill to proper opening size for fixing and operation of handles and fixing approved anodised aluminium standard section around the opening, all complete as per requirement and direction of Engineer-in-charge. |
| 141 | M&L 18/19 mm thick block boards, grade 1 quality, exterior grade, decorative type with decorative face veneer on one faces complete all as specified and as directed by Engr-in-charge. |
| 142 | Cutting holes in brick work built in CM, exc one brick but n exc two bricks for inserting hold fast and making good dismantled portion in CM 1:3 or cement concrete 1:2:4 Type B-1 as required complete all as specified and directed. |
| 143 | S&F 20 mm bore Stop valves, cast copper alloy, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed complete all as specified and directed. |
| 144 | Drilling and tapping GI water mains 50mm bore (in position) for branch connections of the internal dia 20mm, complete all as specified and directed. |
| 145 | S&F straight plain brass ferrules (or connecting screws) screwed both ends and fixed to water mains for tapping branch connection of 20 mm bore pipe, complete all as specified and directed. |
| 146 | S&F Gun metal gate valve, ISI marked, with iron wheel head screwed both ends for iron pipe, fixed in repairs complete of size 20 mm bore |
| 147 | S&F in repair Vitreous China urinals, bowl type (back or corner wall type), complete including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and including 60mm long brass screws, pointing around urinal back in cement; fixing automatic flushing cistern with brackets, flush pipe, grating and Union for discharge pipe. (Exclusive of fixing supply pipe to flushing cistern, trap and waste pipe). |
| 148 | S&F Urinal spreader of PTMT any colour for fixing with 15 mm dia pipe. (Minimum weight 60gms) complete all as specified and directed. |
| 149 | Dismantling old asbestos sheets of any description, any location complete all as specified and directed. |
| 150 | S&F Pre-painted galvalume aluminium zinc coating GI based trapezoidal profile roofing sheets 0.50 mm thick of any colour/ length having tensile strength of 550 MPA AZ-150 as in roof coverings/cladding having effective & overall width 1015 mm &1072 mm respectively, profile hieght 28.5 mm and centre to centre distance between ribs 203 mm fixed with self tapping screws as directed by manufacturer on wooden/steel members including steel scaffolding of any height complete all as specified and directed. |
| 151 | M&L for Pre-painted galvalume aluminum zinc coating GI based Plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and directed. |
| 152 | M&L for PCC (1:3:6) type C-2 (using 40 mm graded crushed stone aggregrate) as in bed to 150mm internal dia RCC/ SGSW drain pipes including packing under and haunching against sides of pipes after they are laid and tested complete all as specified and directed. |
| 153 | M&L for 150 mm bore salt glazed stoneware drain pipes laid in trenches and jointed complete all as specified and directed. |
| 154 | M&L for broken stone or bouler Hardcore of gauge n exc. 63 mm, deposited, spread and levelled in layers n exc. 15 cm thick, watered and rammed to a true surface complete all as specified and as directed. |
| 155 | Supply and filling of broken brick for loose filling, of gauge 40 mm to 80 mm graded complete all as specified and directed. |
| 156 | M&L for surface dressing not exc 15 cm deep in soft/loose soil complete all as specified and directed. |
| 157 | Excavation in trenches, n exc 1.5 m wide and n exc 1.5 m in depth; for foundation, ducting & laying in LT UG cable/GI Pipe, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. n exc 10 sq m on plan and n exc 1.5 m in depth and getting out in soft/loose soil complete all as specified and directed. |
| 158 | Excavation over areas, n exc 1.5 m deep for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, soakage pit etc getting out in soft/loose soil, complete all as specified and directed |
| 159 | Excavation over areas, exc 1.5 m and n exc 3.0 m deep for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, soakage pit etc getting out in soft/loose soil, complete all as specified and directed |
| 160 | Excavation over areas, exc 3.0 m and n exc 4.50 m deep for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, soakage pit etc getting out in soft/loose soil, complete all as specified and directed |
| 161 | Excavation over areas, exc 4.50 m and n exc 6.0 deep for foundation, etc or for shafts, wells, cesspits, manholes, pier holes, soakage pit etc getting out in soft/loose soil, complete all as specified and directed |
| 162 | Excn in post holes (or similar holes) each n.exc. 0.5 Cum, getting out, returning filling in and ramming earth or broken rubble mixed with earth around, in layers n. exc. 25 cm, watering and removing surplus soil to a distance n.exc. 50 m and making surface good in soft/loose soil complete all as specified and directed. |
| 163 | M&L for returning, filling in, including spreading, levelling, watering and well ramming in layers not exc 25 cm in soft/loose soil complete all as specified and directed. |
| 164 | M&L for removing excavated soil n exc 50 m and depositing where directed at a level not exc 1.5 m above the starting point complete all as specified and directed. |
| 165 | Taking up or down existing 80mm bore GI steel tubing and connections (from wall/trenches/floor), including cleaning for re-fixing or removal to store complete all as specified and directed. |
| 166 | All as per item No. 165 here-in-before but 50mm bore GI steel tubing |
| 167 | All as per item No. 165 here-in-before but 40mm bore GI steel tubing |
| 168 | Refixing/shifting of 80mm bore old steel tubing and connections in new or old position with major defects including cleaning internally and externally, any grade/make in trenches/wall/floor/ceiling including all type of new fittings i.e sockets, Tee union elbow etc complete all as specified and directed. |
| 169 | All as per item No.168 here-in-before but 50mm bore old steel tubing |
| 170 | All as per item No. 168 here-in-before but 40mm bore old steel tubing |
| 171 | Supply, fixing & laying 80mm bore GI tubing medium grade as per IS 1239 with one socket both end threaded in any length including cutting threading connection in new or old position and all type of GI new fittings for laid in trenches/wall/ceiling/ floor complete all as specified and directed by Enginner-in-Charge. |
| 172 | All as per item No. 171 here-in-before but 50mm bore GI tubing |
| 173 | All as per item No 171 here-in-before but 40mm bore GI tubing |
| 174 | S&F 50mm bore Gun metal globe or gate valves, confirm IS 778, with iron wheel head, screwed both ends for iron pipe and fixed complete all as specified and directed by Enginner-in-Charge. |
| 175 | All as per item No 174 here-in-before but for 40mm bore Gun metal globe or gate valves |
| 176 | S&F 80mm dia sluice valve, class II, heavy duty, both ends flanged with gun metal spindle & check nut and all nuts, bolts, washers, gaskets etc; including dismantling of old unserviceable sluice valve complete of the following sizes (Note :- for these sluice valves which are fixed with pillar of over head tank work involve such as breaking of PCC/Lead flange joints will be deemed to include in the rate quoted & contractor will also repair the damaged floor etc, to match with existing. (joints shall be measured & paid for seprately) complete all as specified and directed by Enginner-in-Charge. |
| 177 | All as per item No 176 here-in-before but for 100mm dia sluice valve |
| 178 | M&L for construction of brick masonry valve chamber of internal size 1.0x1.0x1.0 mtr with sub class 'B' bricks in CM (1:6) with 3mm thick MS Sheet cover and angle iron frame made out of 40x40x6mm with 2 Nos MS hinges welded to angle iron frame including lifting hook & locking arrangement duly painted with one coat of black bituminous paint over a coat of red oxide primer complete with necessary earth work, brick work, PCC bed, cement plastering, finishing including dismantling and removal of old unserviceble valve pit remains from site complete all as specified and directed. |
| 179 | Dismantling and taking down carefully U/S copper/aluminium point wiring (light, fan, socket, power) complete fitting such as switches, ceiling roses, pendants, lamp holder, light fitting etc including CI/Pressed steel terminals, switch box, and making good the disturbed surface of wall/floor etc, to match with the existing surfaces of wall/floor complete all as specified & directed. |
| 180 | Dismantling and taking down carefully sub-main wiring/ service wire of any size including wooden batten etc and making good the disturbed surfaces of wall/floor to match with the existing wall/floor etc complete all as specified & directed. |
| 181 | Dismantling and taking down carefully existing DB’s any type and making good the disturbed surfaces of wall/floor to match with the existing wall/floor etc complete all as specified & directed. |
| 182 | M&L for Point wiring including with 1.5 Sqmm FRLS-H insulated, unsheathed, multistranded, 1100 Volts grade copper conductor cable single core conforming to IS:694 along with one run of 1.5 Sqmm FRLS-H insulated copper conductor cable green in colour for continuous earthing drawn through and including medium grade rigid PVC conduit conforming to IS:9537 (Pt-III) and its all accessories/junction boxes / inspection covers etc of suitable size but not less than 20mm(OD), concealed in wall/ floor etc including provision of pressed steel terminal box of thickness not less than 18 SWG /with earth dolly of suitable size concealed in wall and covered with 3 mm thick phenolic laminated hylam sheet fixed with brass/GI screws for mounting switches, sockets, fan regulator, etc/modular metal flush box covered with modular frame plate with cover of any size as per site requirement for mounting modular switches, modular sockets, modular fan regulator etc complete all as specified and directed for the following points:-One light/fan/bell/exhaust fan point controlled by one, one-way modular switch 5/6 Amp complete all specified and directed. |
| 183 | One 3pin/5pin 5/6 Amps socket out let on same board controlled by one, one-way modular switch complete all specified and directed. |
| 184 | One 3pin/5pin 5/6 Amps socket out let on independent board controlled by one, one-way modular switch complete all specified and directed . |
| 185 | All as per item No 182 here-in-before but wiring with 2.5 sqmm single core multi stranded copper condcutor 1100 V grade PVC insulated FRLS but unsheathed single core for 16 Amps power point on independent board and 2.5 sqmm FRLS cable as earthwire complete all as specified and directed. |
| 186 | S&F switch piano flush type white finish 5/6 Amps, single pole one way, 230 volts, 50 hz complete all as specified & directed. |
| 187 | S&F socket out let 2 pin 5/6 Amps & 3 pin 5/6 Amps flush type, 230 volts, 50 hz complete all as specified and directed. |
| 188 | S&F switch piano flush type white finish 15/16 Amps, single pole one way, 230 volts, 50 hz complete all as specified & directed. |
| 189 | S&F socket out let 5 pin 15/16 Amps & 3 pin 5/6 Amps flush type, 230 volts, 50 hz complete all as specified & directed. |
| 190 | S&F lamp holder (Angular/Straight), insulated body, with back plate for batten fitting complete all as specified & directed. |
| 191 | S&F LED Bulb 9 Watt (cool day light) having colour temp 6500 K and lumen output 950 suitable for \\"B-22 type to fix on batten holder complete all as specified and directed. |
| 192 | M&L ceiling rose 3 terminal / PVC/ polycarbonate, isolated body complete all as specified and directed. |
| 193 | S&F sheet metal enclosures with metal socket and plug top Single pole and neutral enclosure with a two pin and earth plug and socket complete ISI marked, 230/240 volts, 50 hz with one single pole MCB SP 25 Amps complete all as specified and directed. |
| 194 | S&F MCB distribution board, SPN, 8 way, 230 V, 1 phase, AC and MCBs as outgoing in sheet steel powder painted enclosure double door type with minimum IP 43 degree of protection with built in copper bus bar, neutral link and earth link complete including cutting the wall surfaces for flush mounting of DB and making good with cement plaster, putty and paint to match with the existing surface including taking down existing unserviceable MCB DB of any description complete all as specified and directed.Note: MCBs shall be measured and paid separately. |
| 195 | S&F of MCB distribution board, SPN, 8 way, 230 V, 1 phase, AC and MCBs as outgoing in sheet steel powder painted enclosure double door type with minimum IP 43 degree of protection with built in copper bus bar, neutral link and earth link complete including cutting the wall surfaces for flush mounting of DB and making good with cement plaster, putty and paint to match with the existing surface including taking down existing unserviceable MCB DB of any description complete all as specified and directed.Note: MCBs shall be measured and paid separately. |
| 196 | S&F MCB 40A, 16 KA, SPN, 'C curve, 240 V, 50 Hz including taking down existing unserviceable MCB of any description complete all as specified and directed. |
| 197 | S&F MCB 40A, 16 KA, SPN, 'C curve, 240 V, 50 Hz including taking down existing unserviceable MCB of any description complete all as specified and directed. |
| 198 | S&F MCB 06 to 32A, 10 KA, single Pole, 'C curve, 240 V, 50 Hz including taking down existing unserviceable MCB of any description complete all as specified and directed. |
| 199 | S&F of MCB 06 to 32A, 10 KA, single Pole, 'C curve, 240 V, 50 Hz including taking down existing unserviceable MCB of any description complete all as specified and directed. |
| 200 | S&F LED T5 tube light fitting 20 watts with polycarbonate housing and polycarbonate diffuser with integrated electronic driver with all accessories including connecting up with PVC insulated and PVC sheathed twisted three core flexible copper wire of 0.5 sqmm from ceiling rose to connector of fitting complete all as specified and directed. |
| 201 | S&F in replacement of old unserviceable LED T5 tube light fitting 20 watts with polycarbonate housing and polycarbonate diffuser with integrated electronic driver with all accessories including connecting up with pvc insulated and pvc sheathed twisted three core flexible copper wire of 0.5sqmm from ceiling rose to connector of fitting complete all as specified and directed. |
| 202 | S&F LED mirror light fitting Integral slim LED batten Integral 9 / 10 watts of 2 feet long internally prewired complete with all accessories and including connecting up with PVC insulated and PVC sheathed twisted two core wire of suitable size complete all as specified and directed. |
| 203 | S&F in replacement of old unserviceable LED mirror light fitting Integral slim LED batten Integral 9/10 watts of 2 feet long internally prewired complete with all accessories and including connecting up with PVC insulated and PVC sheathed twisted two core wire of suitable size complete all as specified and directed. |
| 204 | S&F LED street/security light fitting 25 watts with high efficiency long life LEDs with In-built electronic driver complete housed in pressure die-cast aluminium housing covered with polycarbonate cover with IP66 degree of protection including GI pipe bracket made up of 40 mm dia medium grade GI pipe of length 1.50m bent to required shape and fixing on walls with suitable MS clamps (02Nos) made up of 25mmx4mm MS flat, nuts, bolts and washers and provision of 3 core PVC insulated and PVC sheathed twisted three core flexible copper wire of 0.5sqmm from ceiling rose to connector of fitting complete all as specified and directed. |
| 205 | S&F in replacement of LED street/security light fitting 25 watts with high efficiency long life LEDs with In-built electronic driver complete housed in pressure die-cast aluminium housing covered with polycarbonate cover with IP66 degree of protection including GI pipe bracket made up of 40 mm dia medium grade GI pipe of length 1.50m bent to required shape and fixing on walls with suitable MS clamps(02Nos) made up of 25mmx4mm MS flat, nuts, bolts and washers and provision of 3 core PVC insulated and PVC sheathed twisted three core flexible copper wire of 0.5sqmm from ceiling rose to connector of fitting complete all as specified and directed. |
| 206 | S&F sub main wiring two single core 4 sq mm PVC insulated unsheathed stranded copper conductor cable (FRLS) 1100Volts grade drawn in & including rigid PVC conduit 20mm dia or more medium grade concealed in wall along with 2.5 Sq mm PVC insulated unsheathed copper conductor cable (FRLS) as earth wire and wire connected with main earth dolly including cutting chasing and making good disturbed portion all as specified and directed |
| 207 | S&F Exhaust fan Steel body AC single phase 230/240 Volt of size 300 mm sweep 900 RPM complete with louvers including making whole on wall to fix exhaust fan and grouting of nut bolts etc and making good the disturbed sufaces of wall all as specified and directed . |
| 208 | Supply and fixing water heater with temp regulator storage type of capacity 25 Ltr, five star rated AC sinle phase 230 volts 50 Hz, vertical mounting type with stainless steel inner tank of approved colour, with adjustable temperature and plug top complete all as specified and directed. |
| 209 | S&F 1100 volts grade heavy duty cable PVC insulated stranded aluminium conductor twin core, 16 sqmm, served with inner sheathing of PVC tape and overall PVC sheathed in service connections including connecting on LT OH line/ energy meter/DB etc complete all as specified and directed. |
| 210 | S&F in replacement of 1100 volts grade heavy duty cable PVC insulated stranded aluminium conductor twin core, 16sqmm, served with inner sheathing of PVC tape and overall PVC sheathed in service connections including connecting on LT OH line/energy meter/DB etc complete all as specified and directed. |
| 211 | Supply, Installed & fix maintenance free earthing copper bonded steel earth rod of 10 feet long having diameter of 17.2mm with copper bonding thickness of 250 micron,UL listed, CPRI Tested at 25 KA fault current for one second and is provided with universal clamp made of SS earth enhancing compound shall be of 50kg/pit (resistivity is less than 0.12 Ohm meter) tested as per IEC 62561-7. The above arrangements shall be provided with heavy duty earth poly plastic pit cover of 6000 kg load bearing capacity (Size: 270x 240x200mm) and FRLS insulated copper conductor of size 6 sqmm, single core cable drawn through and including light grade GI pipe of size 15 mm upto 7 mtr incl cutting and chases on wall and floor and aking good using PCC complete all as specified and directed.Note :- On testing after completion if the desired earth resistance is not obtained the earthing will be redone at no extra cost. Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Sep 22, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedOct 13, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 17 daysOct 15, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 19 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender