Tender For Special Repairs To Keela Puliyur Periya Kulam In Tenkasi Taluk And District.
Tender Value
6 Lakhs
Estimated cost
Bid Submission
07 Oct 2026
5 days left
EMD
6000
Bank guarantee accepted
Document Fee
Ref. Documents
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Tenkasi → Tamil Nadu
EMD Exemption
Not Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender For Special Repairs To Keela Puliyur Periya Kulam In Tenkasi Taluk And District.
BOQ
| Sl. No. | Item Description |
| 1 | Dismantling clearing away and carefully stacking materials usefull materials for reuse for any thickness of walls in brick or stone masonry in lime mortar walls under 3m high etc., complete complying with standard specification and as directed by the departmental officers. |
| 2 | Earth work excavation for foundation in all kinds of soils and sub soils except hard rock requiring blasting full depth as may be directed and depositing the surplus earth in places shown by the Engineer in - charge of work and leveling the same with all leads and lifts including shoring, strutting, shuttering, baling out water wherever necessary and refilling the sides of foundation with excavated earth in layers of 15cm thick well rammed and consolidated etc. complete, complying with technical specifications and drawings as directed by the Engineer in - charge of work. |
| 3 | Providing and placing in Position of Plain cement concrete of grade M 10 using hard broken stone aggregate of maximum nominal size of 40mm to IS specified grading mixing by mixer machine including dewatering the placement site,laying the concrete in layers and in bays ,compacting and finishing the surface with all leads and lifts watering curing to attain the profile and strength as specified for various depth and height and above ground level etc complete as directed by the Engineer in charge of work complying with the standard specification |
| 4 | Providing and placing in position Plain Cement Concrete of M 15 Graded Mix using broken hard granite coarse aggregate (well graded) 60% of nominal maximum size of 40mm and 40% of nominal maximum size of 20mm and down graded to I.S specified grading (to achieve the specified characteristic strength of 15 N / mm2 in 28 days) and mixing the ingredients in approved mixer including dewatering of the placement site by baling / pumping and diverting wherever necessary, placing in layers and vibrating, watering, curing, finishing the surface with all leads and lifts etc., complete in all respects so as to attain the profile and strength as specified in the approved drawings and specification and as directed by the Engineer incharge of work, complying with standard specifications. ( with vibrator) |
| 5 | Supplying and erecting water tight steel centering for sides and soffits including supports and strutting upto height of 3.29 m high for plain surface such as R.C.C.slabs, vertical slabs,side slabs of R.C.C. Works with all cross bracings using mild steel B.G.10 gauge sheets of size 90cm x 60cm stiffened with welded mild steel angles of size 25mm x 25mm x 3mm for boarding laid over silver oak (country wood) joists of size 10cm x6.5cm spaced at about 90cm centre to centre and suported by casurina props of 10cm to 13cm dia sapaced at 75cm centre to centre complete complying with standard specification and as directed by the by the Engineer incharge of work (The retrieved materials should be taken back by the contractor ). The payment should be made after the concrete is laid. |
| 6 | Without strutting |
| 7 | With strutting |
| 8 | Providing and placing in position Plain Cement concrete of M-20 using broken hard granite coarse aggregate (well graded) of nominal maximum size of 20mm and down graded to IS specified grading and using crushed stone sand(m-sand) ( to achieve the specified characteristic strength of 20 N / mm² in 28 days ) and mixing the incredients in approved mixer including dewatering of the placement site by baling/pumping and diverting wherever necessary placing in layers and watering, curing, finishing the surface with all leads and lifts etc., complete in all respects so as to attain the profile and strength as specified in the approved drawings and specification etc., complete complying with standard specifications and as directed by the Engineer incharge of work. (For wearing coat) (Without vibration) |
| 9 | Fabricating, Supplying and erection of Screw gearing steel shutters of size above upto 1.00 m width consist shutters of skin plate made out of 8mm thick mild steel plate and horizontally stiffened with 65x65x6mm mild steel Angle at an interval not more than 0.50m and vertical stiffeners made out of same section at an interval not more than 0.60m and provided with 8mm mild steel gusset plate of required size on both sides fastened with rust free bolts and nuts etc. Conveying the fabricated shutter by using lorries including loading, unloading and leading the shutter to the vent. Dismantling the eroded shutter and shuttering arrangements by using necessary gas cutting equipment. Erecting the new shutter and the shuttering arrangements in the vent in proper position by using necessary hoisting equipment. The shutter shall be painted with two coats of Anticorrosive black paint over one coat of Red Oxide Primer. The rate including cost of materials consumables, labours power charges, conveyance charges for all equipment required conveying the dismantled materials to the section stores, cost of petty civil works, trial operation of shutter and warranty for 5 years etc.,complete. |
| 10 | Fabricating, supplying and fixing of Shutter Groove Angle made up of 65x65x6mm Mild Steel angle for required height including welding hold fast of size 25x25x6mm Mild steel angle 2 Nos on both sides and conveying and leading the groove angle to the vents. Fixing the angle to the grooves in proper alignment including dismantling the existing damaged groove angles, conveying and stacking at section store. The groove angle should be painted with two coats of AC black paint over one coat of red oxide primer. The rate including cost of materials, consumables, labours charges for all fabricating and hoisting equipments, conveyance, petty civil works and warranty for 5 years etc., complete, etc., |
| 11 | Supplying and fixing of Head Set Assembly Light duty with hexagonal nut (Approximate 50 Kg) made up of cast iron including moulding, machining and the hexagonal nut threaded to suit the Screw Rod provided with thrust bearings for smooth operation. Conveying and leading the head set assembly to the work site. Fixing the head set assembly to the top beam by using required rust free bolts and nuts in proper alignment including dismantling the existing damaged Head set assembly supplied with operating key and the both should be painted with two coats of AC black paint over one coat of red oxide primer. The rate including cost of materials, labours, charges for wooden pattern, moulding and charges for labours and materials and warranty for 5 years etc., complete. |
| 12 | Fabricating, Supplying and fixing of Top Beam made up of 150x75mm (ISMB 150) duly drilled to suit the Head Set Assembly with required bed bolt made out of 25mm mild steel round rod duly threaded with suitable anchorage arrangements to a height of 0.60m with necessary Fish plate made out of 12mm mild steel plate of size 0.30 x 0.15m 2Nos with required holes. Conveying and leading the top beam arrangements to the work site. Fixing the top beam arrangements at the top of the vent in correct position including dismantling the existing eroded top beam, conveying and stacking and the section stores. The top beam should be painted with two coats of AC black paint over one coat of Red Oxide primer. The Rate including cost of materials, labours, charges for all fabricating and hoisting equipments, cost of petty civil works conveyance charges for labours and materials and warranty for 5 years etc.., complete. GST 18% Please Enable Macros to View BoQ information |
| 13 | Fabricating, Supplying and fixing of Top Beam made up of 150x75mm (ISMB 150) duly drilled to suit the Head Set Assembly with required bed bolt made out of 25mm mild steel round rod duly threaded with suitable anchorage arrangements to a height of 0.60m with necessary Fish plate made out of 12mm mild steel plate of size 0.30 x 0.15m 2Nos with required holes. Conveying and leading the top beam arrangements to the work site. Fixing the top beam arrangements at the top of the vent in correct position including dismantling the existing eroded top beam, conveying and stacking and the section stores. The top beam should be painted with two coats of AC black paint over one coat of Red Oxide primer. The Rate including cost of materials, labours, charges for all fabricating and hoisting equipments, cost of petty civil works conveyance charges for labours and materials and warranty for 5 years etc.., complete. GST 18% Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Sep 22, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedOct 07, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 5 daysOct 07, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 5 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender