Tender For special Repair To Joinery And Allied Work Of Officer Mess (Bldg No P-4 Bs) At Hq 41 Inf Bde And special Repairs To Officer Toilet (P-25) And Medicine Store (P-27) Of Central Medical Inspection Room Under Ge (East) Lucknow
Tender Value
47.50 Lakhs
Estimated cost
Bid Submission
21 Oct 2026
4 days left
EMD
95000
Bank guarantee accepted
Document Fee
500
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Lucknow → Uttar Pradesh
EMD Exemption
Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for special Repair To Joinery And Allied Work Of Officer Mess (Bldg No P-4 Bs) At Hq 41 Inf Bde And special Repairs To Officer Toilet (P-25) And Medicine Store (P-27) Of Central Medical Inspection Room Under Ge (East) Lucknow
Corrigendum
| Sr No | Corrigendum Date | Corrigendum | Type | New Submission Date |
|---|---|---|---|---|
| 1 | 13-Oct-2026 | DATE Corrigendum | Date | 21-Oct-2026 |
BOQ
| Sl. No. | Item Description |
| 1 | Taking down cement or cement lime plaster any description from brick or stone walls/ceiling etc including raking out joints, hacking for key & scrubbing down with water all as specified. |
| 2 | M&L for rendering 15mm thick in CM 1:6 on fair faces of brick work or concrete surface of wall and finished surface even and fair complete all as specified and directed. |
| 3 | M&L for rendering 15mm thick in CM 1:4 on other than fair faces of brick work or concrete surface of wall and finishedsurface even and fair complete all as specified and directed. |
| 4 | M&L for preparation of newly/old plastered surfaces of wall and applying two coat of oil emulsion distemper (OBD) over a coat of 2 mm thick wall care putty and over a coat of primer on wall of approved shade/tint complete all as specified & as directed. |
| 5 | M & L for preparation of newly/old plastered surfaces and finishing of walls with Premium Acrylic Smooth exterior paint with Silicone additives of required shade in two coats applied @ 1.43 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm complete all as specified and directed. |
| 6 | M & L for prepration of old plastered ceiling surfaces and applying two coats of white wash on ceiling all as specified. |
| 7 | Taking down chowkhat or frame with shutter (without taking off shutter from the frame) and area exc 1.5 Sqm but n.exc 4 sqm each complete all as specified. |
| 8 | Taking down chowkhat or frame with shutter (without taking off shutter from the frame) and area n.exc 1.5 Sqm each complete all as specified. |
| 9 | S&F for in repair three layer rotational moulded polyethylene water storage tank cylindrical hoisted & fixed in position incl dismantiling water tank complete all as specifed capacity 1000 ltrs complete all as specified and directed. |
| 10 | S&F in repair 20 mm Ball valves high pressure of PTMT with epoxy coated Aluminium rod and high density Plastic ball Screwed for iron pipe and fixed (Minimum weight -210 gms complete all as specified and directed. |
| 11 | S&F in repairs 15 mm bore GI tubing medium grade with all fittings and fixed complete to wall and ceiling or laid in floors including taking down of old pipe line with fittings complete all as specified and directed. |
| 12 | S&F in repairs 20 mm bore GI tubing medium grade with all fittings and fixed complete to wall and ceiling or laid in floors including taking down of old pipe line with fittings complete all as specified and directed. |
| 13 | Dismantling of stone slabs and tiles of any description or thickness in floors, platform, aprons etc laid bedded and pointed in any mortar complete all as specified and directed. |
| 14 | M & L for 20mm thick polished granite (of any type and colour) work (table rubbed and polished ) in steps, Jambs, pillars, window cills, cooking platform and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust and admixture of pigment to match with shade of granite complete all as specified and directed. |
| 15 | Rounding of edges of stone slabs one edge smooth round with polishing to match the finish of granite at top such as in steps, cooking platform, and other similar situations complete all as specified and directed. |
| 16 | S&F of false ceiling at all heights with GRG (Glass Fibre Reinforced Gypsum) False ceiling tiles of size 595x595mm of approved texture, design and patterns having moisture content less than 2% , humidity S&F for Semi perfortated 12mm thick micro tegularedged or 10mm thick squre edged GRG(Glass Fibre Reinforced Gypsum) false ceilijng tiles at all heights with GRC false ceiling tiles of size 595x595 mm of approved texture design and patterns having moisture content less than 2%, humidity resistance of 99% NRC 0.50 to 0.75 as per IS 8225:1987. Noncmbustible as per BS476(para4 )-1970 and light reflectance of 85% ( minimum) to be laid in true horizontal level suspended on interlocking metal T-Grid of hot dipped galvanized iron section of 0.33 mm thick (galvanized @ 120 grams per sqm including both sides) comprising of main T runners of size 15x32mm of length 1200 mm and 3000 mm, cross-T of size 15x 32 mm of length 1200 mm and secondary intermediate cross-T of size 15x32 mm of length 600 mm to from grid module of size 600x600mm, suspended from ceiling using galvanizedmild steel items (galvanized @ 80 grams per sqm) i.e 50mm long 8mm outer diameter M-6 dash fasteners, 6mm dia fully threaded hanger rod upto 1000mm length and L-shape level aduster of length and L- shape leveladjuster of size 85x25x2 mm Galvanised iron perimeter wall angle of size 24x24x0.40 of length 3000mm to be fixed on periphery wall / partition with the help of plastic rawl plugs at 450 mm center and 40mm long dry wall wood screw. The work shall be carried out as per direction of the Engineer-in-Charge |
| 17 | S&F 5 mm thick hollow PVC Wall panlling including PVC beading at corner and top of any design, fixed on wall as per manufacture instruction complete all as specified and directed. |
| 18 | Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing) and rubbish off the premises, all as specified and directed |
| 19 | M & L for vitrified ceramic tiles dark shade digital tiles/(double ultra charged), jointless premium quality 10mm thick (square/ rectanglar) polished, exceeding 0.18 sqm of each tiles not exceeding 0.38 sqm, in floors etc including laid over 15mm thick screed bed of CM 1:6 , set and jointed in neat cement slurry and pointed in white/coloured cement to match complete all as specified. |
| 20 | M & L for glazed ceramic tiles (coloured) jointless premium quality 10mm thick in vertical surfaces 600x300x7-8mm thick set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 10mm thick rendering in cement mortar 1:3 complete all as specified and directed. |
| 21 | M & L for Non-skid ceramic coloured tiles jointless premium quality 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles over & including 15mm thick screed bed in cement & sand mortar 1:6 complete all as specified and as directed. |
| 22 | Surface excavation not exc 30 cm deep averaging 15 cm deep and getting out in soft/ loose soil complete all as specified and as directed. |
| 23 | M & L for hard core free from dust and vegetation of gauge exc. 63 mm but not exc. 100 mm, deposited, spread and leveled in layers not exc. 15 cm thick, watered and rammed to a true surface using broken stone or boulders complete all as specified and directed. |
| 24 | M & L for providing 100 mm thick cement concrete 1:4:8 type D-2 (using 40 mm graded crushed stone aggregate) as in sub floor, sub base of floor finished even and rough to receive the mortar complete all as specified and directed. |
| 25 | S&F exterior tiles (heavy duty) of superior quality 400x400x18-20mm thick of approved size/design/shade set and jointed in neat cement slurry & pointed in white or coloured cement to match as in floor over and including 20mm thick screed bed in cm 1:4 complete all as specified and directed. |
| 26 | S & F 12mm thick toughened glass of one piece without any joint as in hinged doors, partitions automatic doors and similar work including cutting to shape, drilling holes required and pivot at top fancy type SS handle of size not less than 300 mm on both sides of shutter with suitable locking arrangement and all necessary fitting complete all as specified and directed. |
| 27 | S&F for frosted film 150 micron thick premium vinyl stained stickers 24 inches wide and 25 inches length (privacy blackout 84% UVA and 99% UV brays) with logo of approved design for glass door all as specified and directed |
| 28 | M & L for double action floor spring hydraulically regulated made up of minimum 1.25mm thick aluminium alloy sheet foundation box, main body with stainless steel cover, governing pivot made of brass, other parts made of mild steel heavy duty, fixed in repairs, with & including replacement of floor tiles if any broken during repair work and making good disturbed surfaces matching to the existing surfaces complete all as directed. |
| 29 | Supply & fixing Factory made uPVC prelem colour three track three panels sliding window with fly proof S.S wire mesh and 5 mm thick tooughned glass (Two nos. glazed & one nos stainless steel wire mesh panels) upto 1.50m height made of (big series) frame 112 x 52mm & sash 42x 68 mm both having wall thickness of 2.3 ± 0.2 mm and single glazing bead / double glazing bead of appropriate dimension. (Area of window above 1.75 sqm) comprising of uPVC multi- chambered frame, with inbuilt roller track and sash extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), appropriate dimension of uPVC extruded glazing beads and uPVC extruded interlocks, EPDM gasket, wool pile, zinc alloy (white powder coated) touch locks with hook, zinc alloy body with single nylon rollers (weight bearing capacity to be 40 kg), G.I fasteners 100 x 8 mm size for fixing frame to finished wall and necessary stainless steel screws etc. Profile of frame & sash shall be mitred cut and fusion welded at all corners, including drilling of holes for fixing hardware's and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealent filler of approved quality with backer rod of required size and side of uPVC frame will be fixed on wall with fastners and joints filled birla wall care putty and match with distrubed surface to existing finish of wall complete all as specified and directed by Engineer-in-Charge. Note- The cost of toughned glass and stainless steel wire shall be deemed inclusive in quoted unit rate. |
| 30 | S&F of powder coated aluminium Grill (anodised tranparent of dyed to required shade according to IS1868 with minimum anodic coating of grade AC 15) of approved design/pattern, with approved standard section and fixed to the exiting window frame with CP brass/ stainless steel screws @200 mm centre, including cutting the grill to proper opening size for fixing and operation of handles and fixing approved anodised aluminium standard section around the opening, all complete as per requirement and direction of Enginer-in-charge. |
| 31 | S&F powder coated aluminium anodised frame/chowkat of aluminium door fixed with rawal plug and screw or wire expansion hold fasteners complete all as specified and directed. |
| 32 | M & L for providing and fixing powder coated aluminium partly glazed and partly paneled door shutter side hung type using 1.50mm thick standered door section having size of styles, top rails 83x44mm where as bottom rails will be made up of 100x44mm including necessary joining cleats glazing clips, rubber packing, anodized aluminium snap beading screws, anodized aluminium fittings such as 100mm long 3 No. aluminium hinges B-21 ,type 01 No. aluminium tower bolt 200mm long and one no mortise lock 100mm size 4 levers (vertical type) and 01 No 300mm size long aluminium sliding bolt and 02 No fancey type fiber glass 150mm dia circular handle shall be provided to each door and glazing of top panel shall be made of 5.50 thick clear tinted sheet glass and pannelling shall be provided with 18mm thick exterior grade pre laiminated partical board water proof with both side choice laminations complete all as specified and directed.Note- The cost of glass, panels and other builder hardwares shall be deemed inclusive in quoted unit rate. |
| 33 | S&F in repairs aluminium extruded section body door closer hydraulically regulated, designation No.3, universal type, suitable for door shutters of 851 to 1000 mm in width and of weight between 61 to 80 kg complete all as specified and directed. |
| 34 | S&F 75x50mm single rebated factory made 100% solid WPC prelem both side (Wood Polymer Composit) door frame from 100% lead free ( Single & extruded process) material with dencity not less then 780kg /Cum complete all as specified and directed. |
| 35 | S&F 65x100 mm single rebated factory made 100% solid WPC prelem both side (Wood Polymer Composit) door frame from 100% lead free ( Single & extruded process) material with dencity not less then 780kg /Cum complete all as specified and directed. |
| 36 | S&F 65x125 mm single rebated factory made 100% solid WPC prelem both side (Wood Polymer Composit) door frame from 100% lead free ( Single & extruded process) material with dencity not less then 780kg /Cum complete all as specified and directed. |
| 37 | S&F Factory made 30 mm thick 100% solid WPC (Wood Polymer Composite) prelem solid both side 14 micron Flush door shutter with 10mm deep CNC moulding design of required size comprising of virgin PVC resin of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixing all as per direction of Engineer-In-Charge. |
| 38 | S&F 30mm thick factory made solid WPC (Wood plastic composit) moulded glazed door shutter with wire mesh in 04 number of division with brown wood grain texture including SS wire mesh (G-304) 0.36 mm minimum dia of wire and average width of aperature 1.4mm with XPM Aluminium alloy wire cloth of wire shall to be fixed with 15x15 square tube in side rails with screwing 8x28 heat metel zink coated screws can be remove of fix again after changing of wire mesh needed. The density should not be less then 650kg /Cum shall be as per manufacture instruction complete all as specified and as directed |
| 39 | S & F Powder coated aluminium window and ventilator shutters, fixed type without sash bar, aluminium section weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws etc. complete all as specified |
| 40 | S&F powder coated aluminium window and ventilator shutters, side hung type without sash bars, aluminium sections weighing 0.55 kg/m including necessary joining cleats, glazing clips,rubber packing, anodised aluminium snap beading, screws, anodised aluminium fittings such as peg stays 150mm long (1 no.). hinges type B-21 100mm long (2 no.) suitable handle (1 no.) complete all as specified |
| 41 | S & F 4.8mm thick sheet glass ordinary quality and glazing with oil putty/Aluminium beads in square exc 0.5 sqm in each pane including painting / oiling to new putty to match with the existing/new surfaces ground or obsecured to one side complete all as specified and as directed. |
| 42 | S&F 300 mm long stainles steel sliding door bolt with hasp & staple (bolt type) and fixing clips of sheet cast or extruded section and fixing bolt and sliding bolts all as specified |
| 43 | S&F 250 mm long stainless steel sliding door bolt with hasp & staple (bolt type) and fixing clips of sheet cast or extruded section and fixing bolt and sliding bolts all as specified |
| 44 | S & F for stainless steel anodized barrel tower bolts 200 mm of extruded section and fixed complete all as specified and as directed. |
| 45 | S & F for stainless steel anodized barrel tower bolts 150 mm of extruded section and fixed complete all as specified and as directed. |
| 46 | S&F 150 mm size stainless steel handles fabricated type extruded section ,ISI marked complete all as specified and as directed. |
| 47 | S&F 125mm size stainless steel handles fabricated type extruded section ,ISI marked complete all as specified and as directed. |
| 48 | S&F Butt hinges 125 mm stainless steel hinges medium weight and fixed complete all as specified and as directed. |
| 49 | S&F Butt hinges 100 mm stainless steel hinges medium weight and fixed complete all as specified and as directed. |
| 50 | Demolition of brickwork or stone/boulder masonry, built in cement mortar or cement lime mortar including all quoins, arches, pillars, etc but excluding ashlar facings, dressed stonework and precast concrete complete all as specified and as directed. |
| 51 | M&L for brick work with sub class ‘B’ old size bricks, straight or curved on plan exceeding 6m mean radius built in CM 1:4 complete all as specified and as directed. |
| 52 | S&F 18 mm thick solid WPC board of density 600kg/Sqm one side prelaminated decoratiove teak face and other side white and balancing as in kitchen shelf, shutters etc including chawkats and all fitting accessories etc including dismantling, complete all as specified and directed |
| 53 | S&F 150mm long fancy stainles steel handle for cupboard & wardrobe shutter complete all as specified and as directed by Engr-in-charge |
| 54 | S&F continuous (piano) hinges, mild steel, bright finish or electro galvanized width of flaps 30mm (when open) fixed with CP steel screws complete all as specified and as directed. |
| 55 | S&F stainless steel drapery curtain rods standard quality dia not less than 25mm dia with fancy type stainless steel bright finish latoo at both ends and Stainless Steel Bracket for middle support and end support as required all as specified and direced as approved by GE. |
| 56 | M&L for Plastering by using approved ready mix mixture of thickness 15 mm thick with water proofing liquid and taking down cement or cement lime plaster, raking out joints and preparing plastering the wall surface with white cement based polymer modified self curing mortar, including disposal of rubbish, all complete as per the direction of Engineer-in-Charge. |
| 57 | M&L for repair to plaster by using approved readymix mixture of thickness 10 mm and taking down cement or cement lime plaster, raking out joints and preparing plastering the wall surface with white cement based polymer modified self curing mortar, including disposal of rubbish, all complete as per the direction of Engineer-in-Charge |
| 58 | M&L for repair to plaster by using approved readymix mixture of thickness 5 mm and taking down cement or cement lime plaster, raking out joints and preparing plastering the Celing surface with white cement based polymer modified self curing mortar, including disposal of rubbish, all complete as per the direction of Engineer-in-Charge |
| 59 | M&L for preparation of newly plastered surfaces and applying two coats of distempering with 1st quality acrylic distemper (ready mixed) having VOC content less than 50 gms/litre, of approved manufacturer, over a coat of 2mm thick putty and primer of required shade and colour complete, as per manufacturer's specification complete all as specified and directed |
| 60 | Demolition of plain cement concrete of any description and in any position not otherwise specifically provided for in this Schedule complete, all as specified. |
| 61 | M&L for cement concrete 1:3:6 type C2, using 40mm graded crushed stone aggregate 75 mm thick as in plinth protection and flooring and finishing the surface even and smooth without using extra cement including filling of joints with sealing compound Grade A complete all as specified and directed. |
| 62 | S&F stainless steel wire cloth 0.36 mm nominal dia of wire and average width of apeerture 1.40 mm and fixed with tinned tacks, or galvanised wire staples, all as directed. |
| 63 | S&F 5.5 mm thick sheet glass ordinary quality and glazing with oil putty in square exc 0.5 sqm in each pane including painting / oiling to new putty to match with the existing/new surfaces complete all as specified. |
| 64 | M & L for framed work such as grills, gratings, etc.. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe.290.Gde-E-165 complete all as specified and directed. |
| 65 | S&F Vitreous china wash down water closet pan (pedestal pattern) white (excluding fixing bolts flushing cistern and flush pipe ). and trap including connection to drain (or out going pipe) and to flushing pipe anti sphonage pipe etc complete including flush pipes and all joints add if fixed in repairs complete all as specified and directed. |
| 66 | S&F Plastic water closet seat cover coloured/white, closed pattern with flat bottom, and cover and mild steel chromium plated or aluminised hinging device complete all as specified and directed. |
| 67 | S&F in repair health faucet for EWC CP hand hold with flexible pipe 1.5m long with complete fitting set complete all as specified and directed. |
| 68 | S&F in repairs 15mm dia CP two way tap consisting angle valve to control water suitable for jet cleaner complete all as specified and directed. |
| 69 | S&F 10 Litres capacity PVC valve less syphonic action type flushing cistern low level, white with inlet ball valve float and handle including brackets connection to pipes and fixing of lever if any joint between flushing pipe and socket of WC pan pre-made complete all as specified and directed. |
| 70 | S&F in repair Vitreous china wash hand basin white angle back size 550x400 mm including 32 mm dia CP waste coupling long screwed shank fly nut flanged end and embedded in lead to waste pipe excluding piller taps complete fixed specified and directed by enginner -in-charge |
| 71 | S&F 110mm PVC (SWR) junction single (single T) equal or unequal complete all as specified and directed. |
| 72 | S&F in repair 110mm bore PVC (SWR) pipe single socketed in any length with rubber rings joints laid in trenches or wall complete all as specified and directed. |
| 73 | S&F in repair 75mm bore PVC (SWR) pipe single socketed in any length with rubber rings joints laid in trenches or in floor/wall complete all as specified and directed. |
| 74 | S&F 110mm bore PVC (SWR) bends, any radius complete all as specified and directed. |
| 75 | S&F PVC (SWR) bends any radius of 75 mm dia complete all as specified and directed. |
| 76 | S&F PVC (SWR) 75mm floor trap, plain with grating including jointing with solvent cement complete all as specified and directed. |
| 77 | S&F 15mm dia fancy type chromium plated bib taps cast copper alloy with crutch or butterfly handle, scresed down screwed for iron pipe or for brass ferrule and fixed both ends for iron pipe or for unions complete all as specified and directed. |
| 78 | S&F brass chromium plated wall mixer for mixing hot & cold water in 3-in-1 with 1.50m long flexible lead & screwed down for iron pipe of 15mm bore complete all as specified and directed. |
| 79 | S&F in repairs 125 mm dia CP brass shower rose with or without swivel joints any size including fixing to steel pipe or union complete all as specified and directed. |
| 80 | S&F in repair 15 mm dia Pillar tap cast copper alloy chromium plated fancy type with capstan head and cup screwed down screwed for G I pipe or for brass ferrule complete all as specified and directed. |
| 81 | S&F 15mm dia fancy type chromium plated Stop/angle/Conceled valve/cast copper ally screwed down, high pressure, with crutch or butterfly handle screwed both ends for iron pipe or for unions and fixed to GI Pipe complete all as specified and directed. |
| 82 | S&F CP brass towel rails 20 mm dia and 600 mm long fixed as in repair incl chromium plated brass screw and wooden / cleats |
| 83 | S&F in repairs bevelled edge 600mmx450mm bevelled edge mirror of selected quality glass, mounted on 6mm thick AC building board or commercial plywood and fixed to wooden plugs with chromium plated brass screws and cup washers complete all as specified and directed. |
| 84 | S&F PVC connection of 15 mm bore 600 mm long with brass coupling on both ends of superior quality with PTMT nuts fixed as in repair complete all as specified and directed. |
| 85 | S&F in repairs 32 mm dia Waste coupling of PTMT (half or full threaded) (Minimum weight 32mm 45gms/40mm-60 gms) complete all as specified and directed. |
| 86 | S&F in repairs 32mm dia PVC waste pipe approx 900mm long for sink/WHB complete all as specified. |
| 87 | Removing existing roof treatment and preparing surfaces to the entire satisfaction of Engr-in Charge /GE including taking down existing plaster,cleaning of all foreign material such as grass roots dust & mud phuska in any etc and roughening the concrete surfaces by wire brushes and washing down to remove dust etc . flushing at junction of parapets and removing any vegetations and sprinking of anti-vegetation growth chemical at roof slab before roof treatment complete all as specified and directed. |
| 88 | M & L for cement concrete type B-0, 1:2:4 (12.5mm graded crushed stone aggregate) as on roof padding even and fair to receive screed bedding layer complete all as specified and directed. |
| 89 | M&L for 15mm thick on concrete surfaces of roof in cement mortar 1:4, mixed with liquid water proofing compound finished even and smooth without using extra cement . (Liquid water proofing compound to be measured paid separately) complete all as specified and directed. |
| 90 | Supply only Liquid water proofing compound complete all as spesified and directed. |
| 91 | M&L for application of high perfomance hybride polyurea elastomeric water proofing coating cold applied, liquid membrane at 1.5 kg/Sqm with an elongation minimum of 500+100% by roller and tensile strength of minimum 11-13 N/mm2 as per ASTM D2370, crack bridging ability minimum of 3 to 4 mm as per ASTM C1305 , Shore Hardness of minimum 70+5 as per ASTM D2240 complete as per directed by Engr-In-Charge. The System shall also include final base preparation including cleaning of the plaster surface etc and applying epoxy primer as approved makes in two coats at a coverage of 0.20 kg/Sqm, etc as per manufacturer specification, complete all as specified and directed. Note:- The work petaining to water proofing treatment shall be executed for authorized applicator through manufacture of wich the materials is proposed to be used by the contrator and approved by Garrision Engingeer. |
| 92 | Taking down carefully existing surface aluminium or copper point wiring (light, fan, socket, bell or power) including all associated fixtures and fittings such as switches, ceiling roses, regulators, sockets, lamp/angle holder etc and making good the disturbed surfaces to an even and smooth finish using cement mortar 1:3 and applying white/colour wash to match the existing surface complete. |
| 93 | M & L for point wiring with 1100 Volts grade PVC insulated FRLS multi-stranded copper conductor cable 1.5 sqmm including PVC insulated FRLS copper earth continuity conductor 1.5 sqmm, colour-coded as per IS, drawn through and including concealed rigid non-metallic PVC conduit, medium grade, ISI marked, ivory colour of size not less than 25 mm dia with all necessary conduit fittings and accessories such as bends, tees, couplers, junction boxes etc including concealed sunken modular GI metal boxes of minimum 1.0 mm thickness with modular mounting cover plates and frames of approved colour, suitable for mounting modular switches, sockets, regulators, etc complete for the following:– One light point controlled by one switch. Note : Cost of moduler suken boxes, frame and cover plate of requiste module shall be deemed inclusive in quoted unit rate. |
| 94 | All as per Item No 93 here-in-before but One fan point controlled by one switch. |
| 95 | All as per Item No 93 here-in-before but One light point controlled by two, two way switches. |
| 96 | All as per Item No 93 here-in-before but One socket outlet 6 Amp controlled by one switch on the same board with other switches. |
| 97 | All as per Item No 93 here-in-before but One socket outlet 6 Amp controlled by one switch on indepdendent board. |
| 98 | All as per Item No 93 here-in-before but One bell point controlled by one bell push. |
| 99 | M & L for point wiring with 1100 Volts grade PVC insulated FRLS multi-stranded copper conductor cable 2.5 sqmm, including PVC insulated FRLS copper earth continuity conductor 2.5 sqmm, colour-coded as per IS, drawn through and including concealed rigid non-metallic PVC conduit, medium grade, ISI marked, ivory colour, of size not less than 25 mm dia, with all necessary conduit fittings and fixing accessories, including sunken GI metal box of minimum 1.0 mm thickness with modular mounting cover plate and frame of approved colour, suitable for mounting modular accessories, complete for one 6A or 16 A socket outlet point controlled by one switch on independent board.Note : Cost of moduler suken boxes, frame and cover plate of requiste module shall be deemed inclusive in quoted unit rate. |
| 100 | M&L for point wiring with 1100 Volts grade PVC insulated FRLS multi-stranded copper conductor cable 4 sqmm, including PVC insulated FRLS copper earth continuity conductor 4 sqmm, colour-coded as per IS, drawn through and including concealed rigid non-metallic PVC conduit, medium grade, ISI marked, ivory colour, of size not less than 25 mm dia, with all necessary conduit fittings and fixing accessories complete for one 16A/20A socket outlet point controlled by one module MCB on independent board. Note : Cost of moduler suken boxes, frame and cover plate of requiste module shall be deemed inclusive in quoted unit rate. |
| 101 | S & F modular angle lamp holder with 9/12 watt LED bulb of approved make with insulated polycarbonate body with modular frame including necessary fixing accessories and electrical connections complete. |
| 102 | S&F modular one-way switch, 6 Amp, 1-module size of approved make, with all necessary fixing accessories and electrical connections complete. |
| 103 | S&F modular one-way switch, 16 Amp, 1-module size, of approved make, with all necessary fixing accessories and electrical connections complete. |
| 104 | S&F modular two-way switch, 6 Amp, 1-module size of approved make with all necessary fixing accessories and electrical connections complete. |
| 105 | S&F modular bell push switch, 6 Amp, 1-module size of approved make with all necessary fixing accessories and electrical connections complete |
| 106 | S&F AC ding-dong door bell, 240 Volts, single pole of approved mak with all necessary fixing accessories and electrical connections complete. |
| 107 | S&F modular socket outlet, 6 Amp, 2/3 pin combined, 2-module size, of approved make with all necessary fixing accessories and electrical connections complete. |
| 108 | S&F modular socket outlet, 6/16 Amp, 2/3 pin combined, 2-module size, of approved make with all necessary fixing accessories and electrical connections complete. |
| 109 | S&F MCCB, four-pole, 125 Amp, with minimum breaking capacity 16 kA (Icu = Ics), thermally adjustable type with thermal overload setting range from 70% to 100% of rated current, and fixed magnetic short-circuit protection, with spreader links (set of four) for cable connections, suitable cable lugs, nuts, bolts and washers including making all electrical connections complete. |
| 110 | S&F of MCB Distribution Board, factory-assembled type, fabricated from powder-coated CRCA steel sheet, recess-mounted, complete with reversible double door, having a minimum degree of protection IP-43 and mechanical impact resistance IK-09, conforming to IS 61439 (Low-voltage switchgear and controlgear assemblies), provided with insulated tinned copper busbar of 100 Amp rating, separate neutral busbar and earth busbar, DIN rail, detachable gland plate, complete with all internal interconnections, earthing connections, and blanking plates for all unused ways/spaces, complete in all respects, suitable for the following ratings and number of ways:–Note: MCCBs, MCBs and MCB Distribution Boards (DBs) shall be of the same make to ensure proper coordination, compatibility and compliance with applicable IEC standards. |
| 111 | SPN, 240 volts, 4 ways. |
| 112 | SPN, 240 volts, 8 ways. |
| 113 | SPN, 240 volts, 12 ways. |
| 114 | VTPN, 415 volts, 4 ways. |
| 115 | S&F ceiling rose, 3-plate type, with insulated polycarbonate body, of approved make with all necessary fixing accessories and electrical connections complete. |
| 116 | M & L for submain wiring alongwith earth continuity conductor with PVC insulated FRLS multistranded copper conductor cable using colour coding drawing into and including concealed rigid non metallic PVC conduit 20 mm dia, medium grade, ISI marked ivory colour along with accessories of nominal sizes 2x4 sqmm + 1x4 sqmm earth wire including taking down of old unservicable sub main wiring complete all as specified and directed. Note : (i) Cost of cutting & chasing for concealltion of conduit and making good as existing to distrubed surface shall be deemed inclusive in quoted unit rate. (ii) Three runs of 4 sqmm copper conductor and 01 run of PVC conduit shall be measured as one unit. |
| 117 | M & L for submain wiring alongwith earth continuity conductor with PVC insulated FRLS multistranded copper conductor cable using colour coding drawing into and including concealed rigid non metallic PVC conduit 25 mm dia, medium grade, ISI marked ivory colour along with accessories of nominal sizes 2x6 sqmm + 1x6 sqmm earth wire including taking down of old unservicable sub main wiring complete all as specified and directed. Note : (i) Cost of cutting & chasing for concealltion of conduit and making good as existing to distrubed surface shall be deemed inclusive in quoted unit rate. (ii) Three runs of 6 sqmm copper conductor and 01 run of PVC conduit shall be measured as one unit. |
| 118 | Supply and fix in replacement of SP MCB 6 to 32 Amps, 240 v, 50 Hz AC Made from moulded self extinguishing thermostat plastic and suitable for 'C' curve, 10kA breaking capacity complete all as specified and directed. |
| 119 | Supply and fix in replacement of SPN MCB 10 to 32 Amps, 240 v, 50 Hz AC Made from moulded self extinguishing thermostat plastic and suitable for 'C' curve, 10kA breaking capacity complete all as specified and directed. |
| 120 | Supply and fix in replacement of SPN MCB 40 to 63 Amps, 240 v, 50 Hz AC Made from moulded self extinguishing thermostat plastic and suitable for 'C' curve, 25kA breaking capacity complete all as specified and directed. |
| 121 | Supply and fix in replacement of TPN MCB 40 to 63 Amps, 240 v, 50 Hz AC Made from moulded self extinguishing thermostat plastic and suitable for 'C' curve, 25kA breaking capacity complete all as specified and directed. |
| 122 | S&F GI pipe bracket, 32 mm dia, light grade, 1.2 m long, bent to shape for security light fitting including 2 Nos MS clamps with nuts, bolts & washers and painting of clamps with aluminium paint over one coat of red oxide primer complete. |
| 123 | S&F in replacement LED security light fixture 25 to 35 Watt with powder-coated pressure die-cast aluminium body complete with electronic driver suitable for input voltage 140–270 Volts AC, 50 Hz, operating temperature –15°C to +50°C, provided with internal surge protection minimum 5 kV (L–N–E) as per IEC 61000-4-5, driver efficiency >85%, THD <10% as per IEC 61000-3-2, power factor ≥0.95, IP-66 protection and IK-10 impact resistance, CRI >80, system lumen efficacy ≥105 and <120 lm/W, with under-voltage and over-voltage protection, EMI/EMC compliance as per CISPR-15, and optical lenses for beam angle as per IESNA Type I / II / III, as required. The luminaire shall have minimum rated life of 50000 burning hours for LED with 70% lumen maintenance at end of life supported by LM-80 extrapolation and IES TM-21-11 report, CCT 5700K / 6000K / 6500K (ANSI bin), SDCM <5, and maximum power consumption not exceeding rated wattage. The fixture shall conform to relevant BIS standard and shall include all accessories, fixing arrangements, internal wiring with suitable size FRLS PVC insulated copper conductor cable, connections and earthing, complete in all respects and LM-79 and LM-80 test reports from NABL-accredited laboratory, as required under BIS for LED luminaires shall be submitted. |
| 124 | S&F in replacement LED surface-mounted batten light fitting, 20/22 Watt, with powder-coated die-cast/extruded aluminium or CRCA sheet phosphated and powder coated body, construction conforming to IS:10322 (Part-1) / IEC 60598-1 with replaceable high-efficiency electronic driver (driver efficiency ≥85%), system lumen efficacy ≥120 lm/W, suitable for AC 140–270 Volts, 50 Hz, operating temperature –15°C to +40°C. The luminaire shall be provided with internal surge protection minimum 2.5 kV, short-circuit and open-circuit protection, THD <10%, power factor ≥0.95, IP-20 protection, CRI >80, and flicker ≤5%. The LED shall have a minimum rated life of 50000 burning hours with 70% lumen maintenance at end of life. The CCT shall be 5700K / 6000K / 6500K (ANSI bin) with SDCM <3, and maximum power consumption shall not exceed the rated wattage. The luminaire shall conform to relevant BIS standards and bear a valid BIS Trade Mark Certificate (TC). Manufacturer’s name/word mark shall be engraved / embossed / screen-printed on the housing. The item includes internal wiring with suitable size FRLS PVC insulated copper conductor cable, all connections, earthing, fixing accessories, and is complete in all respects and LM-79 and LM-80 test reports from a NABL-accredited laboratory, as mandated under BIS for LED luminaires shall be submitted. |
| 125 | M&L for earthing with galvanised steel earth plate electrode of size 600 mm × 600 mm × 6 mm thick, buried directly in ground with earth pit not less than 2.25 metres deep below normal ground level, with top edge of earth plate not less than 1.5 metres below normal ground level, connected to galvanised steel earth lead wire 4 mm dia by means of galvanised steel bolts, nuts, check nuts and washers, all as shown on Electrical Plate No. 3 of MES SSR Part-I (2009), including 15 mm bore light grade GI protection pipe for earth lead up to 7.5 metres beyond the outer edge of earth pit, PCC chamber in cement concrete 1:3:6 type C-1, with RCC cover slab in cement concrete 1:2:4 type B-1, 40 mm thick, reinforced with 6 mm dia MS bars, 3 Nos each way, provided with lifting handle made out of 6 mm dia MS bar, watering arrangement consisting of funnel with wire mesh and 20 mm bore light grade GI watering pipe, common salt and charcoal filling including necessary excavation, earth work, and testing on completion complete. |
| 126 | S & F of GI box of suitable size fixed in recess with modular front plate and cover including provision and fixing of 20/25 Amp modular socket outlet and 16/20Amp modular SP MCB, ‘C’ curve as per load requirement with all necessary internal wiring connections, fixing arrangements complete. |
| 127 | Taking out old serviceable ceiling fan and wall mounting fan and refixing the same after carried out necessary painting , oiling and replacement of ball bearings and make functional complete all as directed |
| 128 | Taking out old serviceable exhaust fan and PVC air freshner and refixing the same after carried out necessary painting , oiling and replacement of ball bearings and make functional complete all as directed |
| 129 | S&F in repair Stepped type electronic fan regulator flush type on the existing modular switch socket plate complete |
| 130 | S&F in repair of MCB vertical distribution board, triple pole and neutral (TPN), 4-way, 415 Volts, factory-assembled type, conforming to IS/IEC 61439 (Low-voltage switchgear and controlgear assemblies), fabricated from powder-coated CRCA steel sheet enclosure, recess-mounted, suitable for MCCB incomer up to 160 Amp having a minimum degree of protection IP-43 and mechanical impact resistance IK-09 with reversible double door, incorporating insulated tinned copper busbar of 250 Amp rating, separate neutral busbar and earth busbar, DIN rail, and detachable gland plate, including all internal interconnections, earthing connections, and blanking plates for all unused ways/spaces complete. |
| 131 | Supply and fixing recess mounting LED light fitting 2'x2' luminaire architectural recessed luminaire with CRCA housing and Molded PC diffuser with an unique angular optics for making the illumination easy on eyes for light comfort in office areas with UGR<=19. The luminaire should have a color consistency SDCM< 5, CRI > 80 and choice of CCT: 5700K. Luminaire shall be designed to emit at least 3000 lumens and an efficacy of atleast 120Lm/W and maximum system wattage of 36 Watt, designed for ambient temp 45 deg C. The metallic electronic driver shall have a power factor >0.95, THD <10%, 4KV internal surge protection and the Ripple factor should be <5% to minimise the Flicker and Stroboscopic effect Fixture should have an operating voltage range of 140-270VAC incl. all as specified. |
| 132 | S & F of 2 X 36 watt ceiling suspended LED Luminaires, 230 V AC with 3000 K to 6500 K with min Lumen 110/ Watt with high efficiency PMMA Diffuser soft glare free light complete with driver, holder & LED Lamp complete including connecting up with driver three core flexible copper conductor cases of suitable size complete complete suspended on ceiling with suitable multistranded steel wire rope / steel chain of length 600mm to 900 mm (02 Nos) including suitable fastners/hooks in ceiling complete all as specifed |
| 133 | Supply and fix Rigid non-metallic PVC conduit exclusive of boxes (junction/terminal) but inclusive of all tees, bends,elbows, reducers, bell mouth tube ends and fixing accessories such as couplers, lock nuts, saddles, pipe hooks etc.PVC pipe 25 mm dia for protection of cables all as specifid |
| 134 | Supply and fixing Exhaust fan PVC body 250 mm sweep working on single phase supply incl. all accessories including electrical connection with required wire complete all as specified. |
| 135 | Supply and laying of XLPE Insulated armoured electric heavy power cable with aluminium stranded conductor ,1100 volts grade, cross sectional area 25sqmm x 2 core complete |
| 136 | Excavating in trenches, not exceeding 1.5 m wide and not exceeding 1.5 m in depth for laying of cables, pipes etc. and getting out including trimming the sides and forming bottom surfaces to required levels in soft/loose soil complete all as specified . |
| 137 | Returning, filling in, including spreading, levelling, and well ramming in layer not exceeding 25 cm thick in soft/loose soil complete all as specified. |
| 138 | Removing excavated material ( soils) not exceeding 50m and depositing where directed at a level not exceeding 1.5 m above the starting point complete all as specified . |
| 139 | Material and labour for river sand, washed and screened dry for cushioning to under ground cable in trenches below and around under ground cable including spreading and levelling complete all as specified. |
| 140 | M&L laying well burnt old size bricks, sub class \\"B\\" bricks, straight or curved on plan , laid flat with width equal to length of brick , laid dry over electric cable for protection complete all as specified. |
| 141 | Cutting chases in concrete wall/stone for laying PVC conduit and making good to facings where required and pointing in cement mortar 1:3, and making good, cutting not exc 20 cm girth and matching wall color. Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Oct 13, 2026
11:30 IST
Tender Published
Tender notice published.
Completed
Oct 21, 2026
18:00 IST
Corrigendum-1 Issued
Clarifications on tender conditions and amendments issued.
Upcoming · 4 daysOct 21, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 4 daysOct 23, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 6 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender