Tender For Special Repair To Small Arms Kote & Workshop (Bldg No. P-59) At Sqae (A) & Lpr, Khamaria Under Ge (P) No 1 Jabalpur
Tender Value
36.13 Lakhs
Estimated cost
Bid Submission
13 Oct 2026
21 days left
EMD
72300
Bank guarantee accepted
Document Fee
500
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Jabalpur → Madhya Pradesh
EMD Exemption
Not Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for Special Repair To Small Arms Kote & Workshop (Bldg No. P-59) At Sqae (A) & Lpr, Khamaria Under Ge (P) No 1 Jabalpur
BOQ
| Sl. No. | Item Description |
| 1 | Demolition of cement concrete (unreinforced) in ground floors and pavings or in any position n exc 15 cm thickness (below or above ground level) complete all as specified and directed. |
| 2 | M&L for Cement concrete type D2 1:4:8 (using 40 mm graded aggregate) as in foundation filling and mass concrete complete all as specified and directed. |
| 3 | Demolition of Stone slabs and tiles laid bedded and pointed in any mortar of any description or thickness in floors, aprons etc. complete all as specified and directed. |
| 4 | M&L for Machine cut kota stone slab flooring 20-25mm thick over cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing over and including screed bed or bedding layer of cement mortar (1:6) 15 mm thick for laying floor finishes,complete all as specified and directed. |
| 5 | M&L for Kota stone slab 20-25mm thick in riser of steps, skirting, dado and pillar laid over and including cement screed and jointed, with rendering of cement mortar (1:4) 10 mm thick for laying floor finishes, roofs complete all as specified and directed. |
| 6 | M&L for Surface excavation n.exc (not exceeding) 30 cm deep and averaging 15cm deep and getting out,complete all as specified and directed. |
| 7 | M&L for Chequered cement concrete tiles with grey pigment cement and pigments 20cm x 20cm x 25mm thick, set, jointed and pointed in neat cement slurry in floors, over and including screed bed or bedding layer of cement mortar (1:6) 15 mm thick for laying floor finishes, roofs complete all as specified and directed. |
| 8 | Demolition of cement concrete reinforced in Roofs, floors (other than ground floors), beams, staircases, landing, chajjas and similar suspended work complete all as specified and directed. |
| 9 | M&L for RCC M-25 design Mix using 20mm graded aggregate for chajjas, beams, lintel, etc. (20 mm graded aggregate) complete all as specified and directed. |
| 10 | Use and waste for Formwork for concrete to chullah hoods, chajjas, lintel, beams, troughs and similar items including edges, fair finished surfaces complete all as specified and directed. |
| 11 | Demolition of Brickwork or stone/ boulder masonry, built in cement mortar or cement lime mortar including all quoins, arches, pillars, drain etc, but excluding ashlar facings, dressed stonework and precast concrete articles, complete all as specified and directed. |
| 12 | Excavating in trenches, n exc 1.5 m wide and n exc 1.5 m in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. n exc 10 sq m on plan and n exc 1.5 m in depth and getting out,complete all as specified and directed. |
| 13 | M&L for RCC M-25 design Mix using 20mm graded aggregate for Walls, retaining walls, drain, basement walls, ballast walls, basement slabs and the like; any thickness; above top of footings; including attached pilasters and buttresses complete all as specified and directed. Note:- Reinforcement shall be measured and paid separately under respective item. |
| 14 | Use and waste of Formwork to faces of walls, retaining walls, abutments, parapets and staircase railings, sides of basement slab and similar work including attached pillasters, buttresses, complete all as specified and directed. |
| 15 | M&L for TMT Mild steel bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips, complete all as specified and directed. |
| 16 | S&F TMT steel bars but 5mm dia and over upto and including 10mm dia in stirrups, spacers and binders, complete all as specified and directed. |
| 17 | Returning, filling in, including spreading, levelling, watering and well ramming in layers not exc 25 cm,complete all as specified and directed. |
| 18 | Removing excavated material n exc. 50m and depositing where directed at a level n exc. 1.5 m above the starting point, complete all as specified and directed. |
| 19 | Complete removal of of PCC padding over roofs, floors (other than ground floors), beams, staircases, landing, chajjas and similar suspended work including plaster with existing water proofing treatment in any position cleaning, wire brushing, watering & removal of debris outside of MoD land,complete all as specified and directed. |
| 20 | M&L for PCC 1:2:4 type B1 using 20 mm graded stone aggregate as in concrete padding laid to required slope incl finishing the concrete surface fair and even without using extra cement complete all as specified and directed. |
| 21 | M&L for 10 mm thick screed bed or bedding layer of mortar in cement mortar (1:4) for laying roof finish as padding finished with WPC 3% by weight of total cement, complete all as specified and directed. |
| 22 | M&L for Cleaning of plastered roof surfaces and applying a coat of bitumen primer @ 0.30 kg/sqm on top of dry surfaces of finished cement mortar plaster complete all as specified and directed. |
| 23 | M&L for APP polymeric membrane min weighting 3kg/sqm and minimum 3mm thick reinforced with polyster non woven fabric(wt not less than 150 gms/sqm laid on primed surfaces by torch application on method complete all as specified and directed. |
| 24 | Supply and fixing Heat Resistant Terrace Tiles (300 mm x 300 mm x 20 mm) with SRI(solar refractive index) > 78, solar reflection > 0.70 and initial emittance > 0.75 on waterproof and sloped surface of terrace, laid on 20 mm thick cement sand mortar in the ratio of 1:4 (1 cement : 4 coarse sand) and grouting the joints with mix of white cement & marble powder in ratio of 1:1, including rubbing and polishing of the surface upto 3 cuts complete, including providing skirting upto 150 mm height along the parapet walls in the same manner complete all as specified and directed. |
| 25 | M&L for Applying two coats of bituminous base aluminium paint on old Surfaces including preparation complete all as specified and directed. |
| 26 | M&L for 75 mm cement concrete Type C2 1:3:6 (40 mm graded aggregate) in plinth protection and even and finishing cement concrete surface even and smooth without using extra cement complete all as specified and directed. |
| 27 | Taking down cement or cement lime plaster on brick or stone walls, etc. including raking out joints, hacking for key, scrubbing down with water, complete all as specified and directed. |
| 28 | M&L for rendering 15 mm thick on fair faces of brick work or concrete surfaces of Cement plaster 1:6, rendering is to be finished even or smooth (without using extra lime or cement) complete all as specified and directed. |
| 29 | M&L for rendering 5 mm thick on fair faces of brick work or concrete surfaces of Cement plaster 1:3, rendering is to be finished even or smooth (without using extra lime or cement) complete all as specified and directed. |
| 30 | M&L for Brick work with sub class ‘B’ bricks, old size bricks, straight or curved on plan exc 6m mean radius, built in cement mortar 1:6, complete all as specified and directed. |
| 31 | M&L for providing cement concrete B0 1:2:4 (12.5 mm graded aggregate) in holdfast complete all as specified and directed. |
| 32 | Taking down Chowkhat or frames not exc. 1.5 sq. m each with shutters (without taking off shutters from the frames), complete all as specified and directed. |
| 33 | Taking down Chowkhat or frames exc. 1.5 sq. but n exc 4 sq. m each with shutters (without taking off shutters from the frames), complete all as specified and directed. |
| 34 | Dismantling wrought iron or mild steel work of any description not otherwise provided for, complete all as specified and directed. |
| 35 | S&F for powder coated aluminium frame, shutter, grill for doors, windows, ventilators with one or more rebates including joining cleat for fixing etc. complete all as specified and directed. |
| 36 | S&F for Fibre glass reinforced translucent plain sheeting thickness 5 mm with two plain side lap fixed with coach screw and washer in roof, wall, windows etc complete all as specified and directed. |
| 37 | S&F for Factory made single/double extruded WPC (Wood Polymer Composite) solid door/ window/ Ceosetory windows & other Frames/ Chowkhat of size 50 x 125 mm(double rebat) comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2, modules of elasticity 900N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire retardant and fixed in position with MS hold fast/ lugs/ SS dash fasteners of required dia and length including fastenar of 100 mm long 10 mm dia complete all as specified and directed. |
| 38 | S&F for Factory made single extruded WPC (Wood Polymer Composite) solid plain flush door shutter of 30mm size comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, complete all as specified and directed. |
| 39 | S&F Butt hinges of size 100mm, medium weight, cold rolled mild steel, and fixed, complete all as specified and directed. |
| 40 | S&F 300 mm long Mild steel sliding door bolts, plate type, stove enamelled black, with bright bolt not less than 12mm dia with and including a minimum of 6 bolts and nuts, four on bolt plate and two on staple plate and fixed, complete all as specified and directed. |
| 41 | S&F 300 mm long Aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed, complete all as specified and directed. |
| 42 | S&F for 150 mm long Aluminium anodised, barrel tower bolts of extruded section and fixed, complete all as specified and directed. |
| 43 | S&F for 100 mm long Aluminium anodised, barrel tower bolts of extruded section and fixed, complete all as specified and directed. |
| 44 | M&L for new/old plastered surface, three coat of fire resisting paint of any description wood, steel, iron, concrete, brick, stone, etc., exceeding 10cm in width or girth, complete all as specified and directed. |
| 45 | Material & Labour for preparation of new/old external surfaces of wall and applying Two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over new surfaces, complete all as specified and directed. |
| 46 | Supplying and fixing in repairs of 15mm bore dia CPVC pipes of pressure rating 10 kgf/cm2 with all fittings to walls with hooks, ceiling or laid on floor complete all as specified and directed. |
| 47 | Supplying and fixing in repairs of 20mm bore dia CPVC pipes of pressure rating 10 kgf/cm2 with all fittings to walls with hooks, ceiling or laid on floor complete all as specified and directed. |
| 48 | Supplying and fixing in repairs of 25mm bore dia CPVC pipes of pressure rating 10 kgf/cm2 with all fittings to walls with hooks, ceiling or laid on floor complete all as specified and directed. |
| 49 | S&F in repair 110mm bore PVC (SWR) pipes single socketed, in any length with rubber ring joints, including all, laid in fixed to walls. complete all as specified and directed. |
| 50 | S&F 110mm bore PVC (SWR) bends any radius. complete all as specified and directed. |
| 51 | S&F 110mm bore PVC (SWR) junction single, (single T) equal or unequal any radius.complete all as specified and directed. |
| 52 | S&F 110mm bore PVC (SWR) junction double, (double T) equal or unequal any radius.complete all as specified and directed. |
| 53 | S&F 110mm bore PVC (SWR) cowl any radius.complete all as specified and directed. |
| 54 | S&F PVC (SWR) pipe inner dia 75mm single socketed in any length with rubber ring joint laid on wall/ceiling or laying in floors, in repair complete all as specified and directed. |
| 55 | S&F for 75 mm dia PVC (SWR ) bends and radius complete all as specified and directed. |
| 56 | S&F PVC (SWR) junction single, (single T) equal or un equal of 75 mm bore of pipe with access door complete all as specified and directed. |
| 57 | M&L for Glazed coloured ceramic tiles in vertical surface 350x 250x 7 mm/ 450X 350X 7mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match over and including CM 1:4, 10mm thick on fair faces of brick work or concrete surfaces, complete all as specified and directed. |
| 58 | M&L for Non - skid coloured Ceramic tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including screed bed or bedding layer of mortar 15 mm thick for laying floor finishes,complete all as specified and directed. |
| 59 | S&F PVC water tank Rotational moulded polyethylene water storage tanks 500 litres (cylindrical vertical with closed top) three layer hoisted and fixed in position complete all as specified and directed. |
| 60 | S&F 10 litre capacity PVC flushing tank,, syphonic action type, flushing cistern, low level, white, with inlet, ball valve,pvc flush pipe, float and handle incl brackets and waste pipe complete all as specified and directed. |
| 61 | S&F in repairs Vitreous China wash down water closet pan (squatt pattern), white, connection pipe to union of flushing cistern, inlet and overflow pipes,connecting only to flushing cistern anti-syphonage pipe with PVC flush pipe of 32mm dia with mild steel chromoum plated complete all as specified and directed. |
| 62 | S&F Health faucet (ABS Body) mild steel chromium plated suitable for 15 mm dia pipe with 1.25 meter long flexible tube and ABS wall hook including making connections and fixed in position complete all as specified and directed. |
| 63 | S&F 20 mm bore gun matel glove or gate valve valve cast copper alloy with handle screwed both ends for GI out let/inlet pipe or for union including threading to existing pipes on both ends complete all as specified and directed. |
| 64 | S&F Wash hand basin flat back 550x400mm vitreous china (white) including Brass chromium plated waste coupling 32mm bore, Waste pipe PVC 32mm bore,complete all as specified and directed. |
| 65 | M&L for in repairs PVC Nahani trap long neck 100 mm dia, with stainless steel grating including jointing to waste pipe fixed in cement concrete type B1, 1:2:4 complete all as specified and directed. |
| 66 | S&F for PVC connections 15 mm size with PTMT nuts of length 600mm fixed complete all as specified and directed. |
| 67 | S&F in repair 15mm Bib taps, cast copper alloy with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule and fixed, including all fittings complete all as specified and directed. |
| 68 | S&F in repair Pillar taps, cast copper alloy, with capstan heads, chromium plated, screwed down high pressure, with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly-nuts, screwed for iron pipe and fixed, including all fittings complete all as specified and directed. |
| 69 | Taking down copper/aluminium point wiring(light,fan, socket or power) complete, including fixture and fittings such as switches, ceiling roses, pendants, regulators, sockets, light fitting etc. removing materials to store for keeping in safe custody or for taking credit(credit for above items should be made as per conitions separately) and making good distrubed surfaces of walls, floors etc. complete all as specified and directed. Note :-1. Contractor has to submit existing bldg inventory items having details of serviceable and unsearviceable and physically verified with JE E/M during the handing taking of sites and before commencement of work.2. If work commence without signing of E/M inventory then contractor will be solely responsible for missing of E/M items and decision of engr-in-charge will be final in this regard.3. All E/M items received from site as a schedule of credit should be stores at location decided by engr-in-charge and should be taken out from bldg premises / stored location with confirmation to engr-in-charge |
| 70 | Taking down submain wiring any type and in any size including making good to disturbed surface, matching with existing complete all as specified and directed. |
| 71 | Taking down existing light fittings any type/any capacity cleaning completely to remove the dust and other particulars including checking of all connection and re-fixing the same in original position including provision of single core flexible wire upto ceiling rose complete all as specified and directed. |
| 72 | M&L for Point wiring for explosive atmosphere with 1100 volts grade, PVC insulated single core FRLS cable with stranded copper conductor of size 2.5 sqmm drawn through and including ERW rigid enamelled steel conduit of size 18/19 mm dia with bends, elbows, couplings etc. duly approved by CMRI Dhanbad and as per IS , flexed with PVC FRLS, insulated unsheathed multi stranded copper conductor cable of 2.5 sqmm as an earth wire connected to common earth and earth dolly as per IS specification for one light point controlled by one switch complete all as specified and directed. |
| 73 | M&L for in repairs for wiring for explosive atmosphere with two single core 2.5 Sqmm multi stranded copper conductor, FRLS, PVC insulated, unsheathed cable, ISI marked, drawn into ERW steel conduit including 2.5 Sqmm FRLS, PVC insulated and unsheathed stranded copper conductor as earth wire in surface/recess including taking down unserviceable sub-main wiring of any description and making good to the disturbed surfaces to match the existing surfaces complete all as specified and directed. Note : Two runs of 2.5 Sqmm copper conductor cable, one run of 2.5 sqmm copper conductor and one run of steel conduit will be measured as one unit. |
| 74 | Supply and fixing LED light fitting 2x16/18/20 Watt flame proof, CMRI certified recommended for gas/ vapor group of IIA & IIIB, Zone 1 & 2 and IP 65 protection with die cast aluminum hosing with heat resistant toughened glass with LED tube light fixtures driver, holders, connector etc. Complete with all accessories prewired and including connecting up with three core flexible copper conductor cable with suitable size flexible metalic hose conduit from juction box to tube light fittings not less than 500mm long of size. complete all as specified and directed. |
| 75 | Supply and fixing flame proof cum waterproof LED light buk head fitting of 40W/45 W. IP66 protection of cast Aluminum alloy meterail and Heat and Impact resistance toughen 'A' clear glass having Anti corrosive epoxy powder coated finish complete with all accessories pre wired and including connecting up with three core flexible copper conductor cable with suitable size.complete all as specified and directed. |
| 76 | Supply and Fix in repair flame proof /weather proof roatary ON/OFF switch, with terminal box capacity 16 amp. complete all as specified and directed. |
| 77 | Supply and fix flame proof /weather proof SS metallic flexible hose pipe from junction box to light fittings/ power socket not less than 300 mm long of size 20 mm duly approved by CMRI Dhanbad. complete all as specified and directed. |
| 78 | Supply and Fix in repair flame proof /weather proof junction box 4way (100 mm Dia). complete all as specified and directed. |
| 79 | Supply and fix enclosed, Flame proof weather proof distribution board SPN 6 Way (Enclosure Size: 250X250mm) FLP Lighting Distribution Panel Incoming: - MCB, 2P, 32Amp — 1 no, Outgoing: - MCB, SP, upto 32 Amp- 4 nos ,With complete internal Bus bar & wiring up to terminals. complete all as specified and directed. |
| 80 | M&L for earthing complete with galvanized steel earth plate electrode 600x600x6.0mm thick directly burried in the ground (earth pit not less than 2.25M deep below ground level) with top edge of earth plate not less than 1.50M deep below normal ground level, connected to galvanised wire of size 4mm by means of bolts, nuts, check nuts and washers of galvanised iron or steel, 40mm bore GI pipe medium grade including necessary fittings for protection of earthing strip, watering pipe 20mm bore GI medium grade, concrete chamber in PCC (1:4:8) type D-2 using 40 mm grade aggregate, coping shall be in PCC (1:3:6) type C-1 using 20 mm grade aggregate and internal surfaces of concrete chamber shall be given 12mm thick plaster in CM (1:4), funnel with wire gauge of 22 gauge (0.63 mm) 8 mesh per linear incl 50mm thick cover of RCC (1:2:4) type B-1 using 20mm grade stone aggregate reinforced with 8mm MS deformed bar @ 75 mm C/C both ways, char coal dust and common salt all as shown in electrical plate No. 3 of SSR Part-I (2009) including all necessary excavation & earth work and removal of surplus soil to a distance n. exc 50M and providing connection points with MS/ GI bolts & washers as required and connection from earth test point to earth electrode with same GI earth wire alongwith 15 mm GI protection pipe and testing on complete all as specified and directed. |
| 81 | Schedule of credit of Amount Rs.34,438.00 to be deducted during AOC. Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Sep 22, 2026
11:30 IST
Tender Published
Tender notice published.
TodayOct 13, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 21 daysOct 20, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 28 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender