Tender For special Repair Of Guard Living Accn (Bldg No P/467, P/469 & P/470) Of Ap Area Of Dou And Boundary Wall Rear Side Of Bldg No P-33 At Aro Silchar Under Masimpur Mil Stn
Tender Value
42.20 Lakhs
Estimated cost
Bid Submission
14 Oct 2026
21 days left
EMD
84400
Bank guarantee accepted
Document Fee
500
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Cachar → Assam
EMD Exemption
Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for special Repair Of Guard Living Accn (Bldg No P/467, P/469 & P/470) Of Ap Area Of Dou And Boundary Wall Rear Side Of Bldg No P-33 At Aro Silchar Under Masimpur Mil Stn
BOQ
| Sl. No. | Item Description |
| 1 | B & R Division Items |
| 2 | Demolition of un-reinforced cement concrete in ground floor and paving not exceeding 15 cm thick (below or above ground level) complete all as specified and directed. |
| 3 | Demolition of brick work or stone/ boulder masonry, built in cement mortar including all quoins, pillars etc. complete all as specified and as directed. |
| 4 | Dismantling floor, hearth or wall tilling including cement mortar bedding (but not backing) removing serviceable tiles to stores and rubbish off the premises. |
| 5 | Dismantling mild steel work or wrought iron of any description and in any position complete all as specified and as directed. |
| 6 | Dismantling plain or corrugated steel sheeting, any gauge or any thickness as in roof covering, wall cladding, etc.including all necessary staging / scaffolding, etc. as required complete all as specified and as directed. |
| 7 | Dismantling wall and ceiling boards (fibre, pulb, insulation etc) or insulation boards slabs/blankets any thickness including cover fillets all as specified and as directed. |
| 8 | Dismantling boarding any description fixed in any position with nails all as specified. |
| 9 | Dismantling of rain water/sewage pipe of any type and any size including fitting complete all as specified and as directed. |
| 10 | Taking down cement plaster on brick or stone walls etc, including raking out joints, hacking for key scrubing down with water etc complete all as specified and as directed. |
| 11 | Taking down chowkhats or frame with shutters (without taking off shutters from frame) each not exceeding 1.50 Sqm each complete all as specified. |
| 12 | Taking down Chowkhats or frames with shutters exceeding 1.5 Sqm but not exceeding 4 Sqm each (without taking off shutters from the frame) complete all as specified. |
| 13 | Taking up or down 15mm dia GI steel tubing and connections, including cleaning for refixing or removal to store complete all as specified and as directed. |
| 14 | Taking up or down 20mm dia GI steel tubing and connections, including cleaning for refixing or removal to store complete all as specified and as directed. |
| 15 | Excavating in trenches, n exc 1.50 m wide and n exc 1.5 m in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. n exc 10 sq m on plan and n exc 1.5 m in depth and getting out soft/ loose type of soil complete all as specified and directed. |
| 16 | Excavating in trenches, n exc 1.50 m wide and depth exc 1.5 m but not exc 3.0m indepth (n.exc 10sqm on plan area) for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. n exc 10 sq m on plan and n exc 1.5 m in depth and getting out soft/loose type of soil complete all as specified and directed. |
| 17 | Returning, filling in trenches including spreading, leveling watering and ramming in layers not exceeding 25cm all as specified. |
| 18 | Removing of surplus soil not exceeding 50 m and deposited where directed at a level not exceeding 1.50m above the starting point all as specified. |
| 19 | M&L for plain cement concrete (1:4:8), Type D2 using 40 mm graded stone aggregate as in foundations, sub-base,filling and mass concrete complete all as specified. |
| 20 | M & L for plain cement concrete 1:3:6 type C-2 (using 40mm graded stone aggregates) as in plinth protection 75mm thick finished over and smooth without using extra cement complete all as specified and dirceted |
| 21 | M & L for 25mm thick Plain Cement concrete type B1 1:2:4 (12.5mm graded crushed stone aggregates) as in floors all as specified and directed. |
| 22 | Use and waste formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams; and similar work; vertical or to batter rough finished flat surfaces of concrete complete all as specified and as directed. |
| 23 | Use and waste of formwork to sides of pillars, posts, struts, piers, columns and stanchions for rough finished flat surfaces of concrete all as specified and directed. |
| 24 | Use and waste formwork to sides and soffits of floor or roof beam, beam hunching, girder, lintels, cantilever, shelves including supports etc for rough finished flat surfaces of concrete complete all as specified and directed |
| 25 | M & L for Reinforced Cement Concrete M-25 (design mix) using 20 mm graded aggregate as in foundation including rafts, footings, foundation beams, plinth beams, bases for columns etc complete all as specified and directed. |
| 26 | M & L for Reinforced Cement Concrete M-25 (design mix) using 20 mm graded aggregate as in column, pillars, piers, posts, and struts complete all as specified and directed. |
| 27 | M & L for Reinforced Cement Concrete M-25 (design mix) using 20 mm graded aggregate as in beams, cantilever, lintels over 1.5m complete all as specified and directed. |
| 28 | M & L for Mild steel TMT Bars 10mm dia and over, cut to length bend to shape as required including cranking, hooking etc and binding with and including mild steel wire (annealed) not less than 0.9 mm dia complete all as specified and directed. |
| 29 | M & L for Mild steel TMT Bars 6mm to 8mm dia, cut to length bend to shape as required including cranking, hooking etc and binding with and including mild steel wire (annealed) not less than 0.9 mm dia complete all as specified and directed. |
| 30 | M & L for brickwork with subclass 'B' straight or curved on plan exc 6 m mean radius, built in CM (1:4) complete all as specified and directed. |
| 31 | M & L for brick work with subclass 'B' or locally available best quality old size bricks, straight or curved on plan exc 6 m mean radius, built in cement mortar (1:4) use old bricks complete all as specified and directed.Note :- Old Bricks will be obtained from the relevant items. |
| 32 | M & L for 10mm thick rendering in cement mortar 1:6 on other than fair faces of brick wall or concrete surfaces, finished even and smooth without using extra cement complete all as specified. |
| 33 | M & L for 15mm thick rendering in cement mortar 1:4 on fair faces of brick wall or concrete surfaces, finished the surfaces even and fair without using extra cement complete all as specified. |
| 34 | M & L for 15 mm thick rendering in cement mortar 1:4 on other than fair faces of brick wall or concrete surfaces, finished the surfaces even and fair without using extra cement complete all as specified. |
| 35 | M & L rendering 15 mm thick cement mortar (1:4) on any faces of brick wall or concrete surfaces, in two layer each of 10+5 mm thick & water proofing compound finished even and fair without using extra cement complete all as specified. (Note :WPC measured separately). |
| 36 | Supply only integral water proffing compound WPC complete all as specified. |
| 37 | M & L Non Skid ceramic coloured tiles 7 to 8mm thick (square/ rectangular) area of each tile not exceeding 0.36 sqm, as in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tile over including 15 mm thick screed bed or bedding layers in cement mortar 1:4 for tile over brushing with neat cement slurry as specified |
| 38 | M & L Non Skid ceramic coloured tiles 7 to 8mm thick (square/ rectangular) area of each tile not exceeding 0.36 sqm, as in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tile over including 10 mm thick as backing coat cement mortar 1:4 laying of skirting/dado on walls all as specified |
| 39 | M & L Non Skid ceramic tiles coloured 7 to 8mm thick (square/ rectangular) area of each tile exceeding 0.06 but not exceeding 0.11 sqm, as in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tile including 15 mm thick screed bed or bedding layers in cement mortar 1:4 over brushing with neat cement slurry complete all as specified. |
| 40 | M & L Glazed ceramic coloured tiles in vertical surface size 450mm X 300mm X & ( 6mm to 7mm )mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match over & including 10mm thick screed bed or backing coat in cement mortar 1:4 laying of skirting/dado on walls all as specified and directed. |
| 41 | S & F pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified. |
| 42 | S & F pre-painted galvalume aluminium zinc coating GI based plain steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified. |
| 43 | S & F Framed work such as grills, gratings, etc.. with ends of bars or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe.290.Gde-E-165 complete all as specified and directed. |
| 44 | S & F MS clamp , made out of any MS section as required at site incl nuts -bolts & washers of suitable size incl necessary welding & two coats of synthetic enamel paint over one coat of red oxide primer using steel conforming to Fe-290 Gde-E-165 fixed complete all as specified. |
| 45 | S & F Factory Made Solid PVC Moulded Door Shutter, 28 to 30mm thick (stiles), with 2, 4, or 6 raised panel design with 2mm thick 3D wood grain Moulded PVC Sheet plyurethane painted on the front face & 2mm plain colour termite proof, water proof and fire resistant PVC sheet on back face, supplying & fixing in frame at site as per specification & drawing complete all as specified. |
| 46 | S&F Factory made single extruded WPC (Wood Polymer Composite) solid door/ window/ Ceosetory windows & other Frames/Chowkhat of size 45 x 70 mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calciumcarbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2, modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixed in position with MS hold fastlugs/SS dash fasteners of required dia and length complete as per direction of Engineer-in-Charge. (M.S. hold fast/ lugs or SS dash fasteners shall be paid forseparately). Note: For WPC solid door/window frames, minus 5mm tolerance in dimension i.e. depth and width of profile shall be acceptable. Variation in profile dimensions on plus side shall be acceptable but no extra payment on this account shall be made. |
| 47 | Factory made single extruded WPC (Wood Polymer Composite) solid plain flush door shutter of 30mm size comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) and 900 N (Edge), minimum compressive strength 50 N/mm, modulus of elasticity 850N/mm? and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixing with stainless steel butt hings of required size with necessary full body threaded star headed counter sunk S.S screws, all as per direction of Engineer-In-Charge. (Note: stainless steel butt hinges and necessary SS screws shall be paid separately |
| 48 | S & F factory made uPVC white colour Three track three panels sliding window with fly proof S.S wire mesh (Two nos. glazed & one no. wire mesh panels) upto 1.50m height made of (big series) frame 116 x 45 mm & sash 46 x 62 mm both having wall thickness of 2.3 ± 0.2 mm and single glazing bead / double glazing bead of appropriate dimension. (Area of window above 1.75 sqm) comprising of uPVC multichambered frame, with inbuilt roller track and sash extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), appropriate dimension of uPVC extruded glazing beads and uPVC extruded interlocks, EPDM gasket, wool pile, zinc alloy (white powder coated) touch locks with hook, zinc alloy body with single nylon rollers (weight bearing capacity to be 40 kg), G.I fasteners 100 x 8 mm size for fixing frame to finished wall and necessary stainless steel screws etc. Profile of frame & sash shall be mitred cut and fusion welded at all corners, including drilling of holes for fixing hardware's and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealent over backer rod of required size and of approved quality, complete all as specified and directed by Engineer-in-Charge. (Glass or wiremesh shall be paid separately) |
| 49 | S & F Pressed steel frames made of 1.25mm thick MS sheet of profile 125x60mm for door and window frames with one or more rebates including hinges, lock strike plate, shock absorber, treating of internal surfaces of chowkhats with coal tar or black paint including hinges, hold fasts/lugs etc complete all as specified. |
| 50 | M & L Plain Cement concrete (1:3:6), type C-0 using 12.5mm graded stone aggregate as in back filling of steel frame holdfast and similar likes including necessary formwork complete all as specified. |
| 51 | M & L for 2nd class fillet square, rectangular or tringular in section wrought screwed with nails exc 13sqcm and n.exc 25sqcm complete all as specified and directed. |
| 52 | S&F 2nd class hard wood 35mm thick glazed and skeleton shutters divided into square, with plain, chamfered or rounded mitred and any number of panels, prepared to receive glass, gauge etc. edge of frames chamfered or round size of numbers of shutters as specified in SSR Part I section 8 clause 8.24(a) complete all as specified and directed. |
| 53 | S&F Powder coated aluminium (minimum thickness of powder coating 50 micron) for shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber/neoprene gasket required (Fittings shall be paid for separately) with extruded built up standard tubular sections/ appropriate Z-sections and other sections of approved make conforming to IS: 733 and IS:1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing/ paneling, C.P. brass/ stainless steel screws all complete as per architectural drawings and the directions of Engineer-in-charge |
| 54 | S & F Stainless steel wire cloth. 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples complete all as specified. |
| 55 | S&F 4.00mm thick sheet glass ordinary quality and glazing with oil putting square n exc 0.5 sqm in each pane complete all as specified. |
| 56 | S&F 75mm long MS Butt hinges, medium weight, cold rolled complete all as specified. |
| 57 | S & F 150 mm long aluminium handles cast type anodised complete all as specified & directed . |
| 58 | S & F 150 mm long aluminum anodised barrel tower bolts of extruded section complete all as specified and directed. |
| 59 | S & F 200 mm long aluminum anodised barrel tower bolts of extruded section complete all as specified and directed. |
| 60 | S & F 200mm long Aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixedcomplete all as specified. |
| 61 | S&F Door stopper of aluminium alloy body and tongue, anodised with hard drawn steel springs, fixed to door with over all length 150mm with rubber bush complete all as specified and directed |
| 62 | S&F Door closer hydraulically regulated (cast iron), designation no. 1 universal type, suitable for door shutters up to 700mm in width and of weight not more than 35kg complete all as specified and directed |
| 63 | S&F as in repairs 25mm dia and 1mm thick MS chromium plated curtain rods with fixing side fancy type brackets end knobs, rings @10nos per running meter and fixed with PVC rawl plugs & steel screws etc all as specified and directed . |
| 64 | S & F, vitreous china wash basin, white flat back size 550 x 400 mm, excluding taps, waste chain, plug and porcelain stopper but including waste coupling, brackets, cutting for and pinning in ends of bracket or erecting stand complete all as specified. |
| 65 | Supply & Fixed in repairs Vitreous china wash down water closet pan ( pedestal pattern ) , white P or S trap including seat cover but excluding fixing bolts, flushing cistern and flush pipe complete all as specified and as directed. |
| 66 | S & F PVC valveless, syphonic action type, low level flushing cistren 10 ltr capacity white with inlet, ball valve float and handle including brackets complete all as specified. |
| 67 | S & F soap dish chromium plated standerd quality fixed on wall with brass screw complete all as specified. |
| 68 | S & F PVC connections 15mm size with PTMT nuts of length 450 m complete all as specified. |
| 69 | S & F 15mm bore pillar tap cast copper alloy with capstan head, chromium plated concealed screwed down high pressure with or without hot or cold with long shunk screwed shanks and fly nuts screwed for iron pipes and connecting to water pipe line complete all specified and directed. |
| 70 | S&F 15mm bore bib taps ,cast copper alloy, chromium plated with crutch or butter fly handle, screwed down for iron pipe or for brass ferrule including accessories complete all as specified and directed. |
| 71 | S & F 15mm bore angle valve, cast copper screwed down high pressure, with crutch or butterfly handle for 15 mm bore pipe or for unions complete all specified and directed. |
| 72 | S & F 15mm bore stop valve, screwed down high pressure, with crutch or butterfly handle for 15 mm bore pipe or for unions complete all specified and directed. |
| 73 | S & F Chromium plated shower roses with or without swivel joints any size including fixing to steel pipe or union with shower arm 15mm size, 195mm long with bend of 45degree with flange of PTMT etc complete all as specified and directed. |
| 74 | S & F 600mm X 450mm bevelled edge mirror of selected quality glass, mounted on 6mm thick AC building board or commercial plywood and fixed to wooden plugs with chromium plated brass screws and cup washers complete all as specified and directed. |
| 75 | S & F in repair Towel rail, 20mm dia brass chromium plated, 600mm long with fancy type brass chromium plated brackets on both sides and fixed with steel screws and wooden/rawl plugs complete all as specified. |
| 76 | Supplying and laying of CPVC pipes 16mm bore SDR 11 & Plain CPVC SDR 11 fittings in trenches complete all as specified. |
| 77 | Supplying and laying of CPVC pipes 20mm bore SDR 11 & Plain CPVC SDR 11 fittings in trenches complete all as specified. |
| 78 | S & F in repair 110mm bore PVC (SWR) pipes single socketed with rubber joint, in any length, laid in trenches or in floors / fixed to walls complete all as specified. |
| 79 | S & F 110mm bore PVC (SWR) bend suitable for pipe complete all as specified. |
| 80 | S & F 110mm bore PVC (SWR) junction, single T equal or unequal with or without door access complete all as specified. |
| 81 | Cutting grooves or rebates not exceeding 20 cm girth, and trimming with or without reinforced surfaces complete all as specified and directed. |
| 82 | M & L for suspended false ceiling using E-grid 2430, 180 GSM (exposed ceiling suspension system) of grid size 600mmx600mm with main runner 38 mm x 24 mm and wall angle 24mm x 24mm using 4mm thick high Pressure high pressure Non Asbestos Fiber Cement decorative Board (E-Board Classic) in a grid of GI system duly suspended with 4 mm dia GI bar hanger fixed with steel dash fasteners or iron purline from the roof with adjustment clip providing positions for light fixtures, air conditioning diffuser and ducts, sprinkler, smoke detectors etc. The main runners to be secured to structural soffits by hanger @ 1220 mm maximum c/c. The last hanger at the end of each main runner should not be placed at more than 450mm from the adjucent wall, flush fiiting 1220mm cross tee to be interlocked between main runners @ 610mm c/c, as to form 600 mm x 600 mm grid and incl apply coloured painting work with two coat of acrylic emulsion paint over a coat of cement primer before installing it on the grid all as specified and directed. Make : Everest Industries Ltd or equivalent as per IS 14862 all as specified and directed. |
| 83 | M & L for preparation of new plastered surface of walls and applying two coat of cement base paint over one coat of wall primer, complete all as specified. |
| 84 | M & L for preparation of new plastered surface of walls and applying two coat of oil emulsion distemper over a coat of primer complete all as specified. |
| 85 | Material & Labour for preparation of new plastered surface applying two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm using roller complete all as specified and directed. |
| 86 | M & L for preparation of new wooden surfaces of any description not other wise described over 10 cm width or girth and applying two coat of Synthetic enamel paint over a coat of pink primer complete all as specified and as directed. |
| 87 | Preparation of new steel surfaces surfaces of any description, over 10cm in width or girth, not otherwise described and applying two coats of synthetic enamel paint over a coat of red oxide primer of surfaces complete all as specified. |
| 88 | M & L for preparation of old steel surfaces of any description over 10 cm width or girth and applying two coat of Synthetic enamel paint complete all as specified and as directed. |
| 89 | E & M Division items |
| 90 | Taking down carefully copper/aluminium point wiring (light, fan, buzzer, socket or power) complete including fixture and fittings such as switches, ceiling roses, pendants, regulators, sockets, light fitting etc including removing from site for taking credit and making good to disturbed surface of walls, floors etc as per existing specification complete all as specified and as directed. |
| 91 | Taking down carefully submain wiring including all accessories without disturbing existing wiring fittings fixtures etc and making good to the disturbed surfaces all as directed and as specified in any type and size all as directed. |
| 92 | Dismantling old unserviceable main switches, sheet metal enclosures DB including MCBs etc and removing from site for taking credit incl making good to disturbed surface of wall as per existing specification complete all as specified and as directed. |
| 93 | Dismantling of U/s GI pipe of size 40 mm/50mm bore complete all as specified and directed. |
| 94 | Taking out old U/s XLPE cable of any size/type taking out of olf bricks/cable cover complete all as specified and directed. (Excavation and earth work will be measured and paid separately under respective items) |
| 95 | Taking out old U/s GI PIPE of any size/type including all fittings etc complete all as specified and directed. (Excavation and earth work will be measured and paid separately under respective items) |
| 96 | M & L for point wiring with FRLSH stranded copper conductor 1.5 sqmm (nominal area), two single core, PVC insulated cable 1100 volts grade, ISI-694 marked in and including heavy duty,concealed PVC Conduit including all accessories etc ISI marked, with GI sunken box suitable for fixing switches, sockets and regulators including PVC insulated stranded copper conductor 1.5 sqmm (nominal area) single core cable as earth continuity conductor to common earth and connecting to earth dolly complete all as specified and directed for One light point controlled by one switch. |
| 97 | M & L for point wiring with FRLSH stranded copper conductor 1.5 sqmm (nominal area), two single core, PVC insulated cable 1100 volts grade, ISI-694 marked in and including heavy duty, concealed PVC Conduit including all accessories etc ISI marked, with GI sunken box suitable for fixing switches, sockets and regulators including PVC insulated stranded copper conductor 1.5 sqmm (nominal area) single core cable as earth continuity conductor to common earth and connecting to earth dolly complete all as specified and directed for One fan point/exhaust fan point controlled by one, one way switch . |
| 98 | M & L for point wiring with FRLSH stranded copper conductor 1.5 sqmm (nominal area), two single core, PVC insulated cable 1100 volts grade, ISI-694 marked in and including heavy duty, concealed PVC Conduit including all accessories etc ISI marked, with GI sunken box suitable for fixing switches, sockets and regulators including PVC insulated stranded copper conductor 1.5 sqmm (nominal area) single core cable as earth continuity conductor to common earth and connecting to earth dolly complete all as specified and directed for One 3 pin 5 Amp socket outlet point controlled by one switch on the same board. |
| 99 | M & L for point wiring with FRLSH stranded copper conductor 1.5 sqmm (nominal area), two single core, PVC insulated cable 1100 volts grade, ISI-694 marked in and including heavy duty, PVC Conduit including all accessories etc ISI marked, with GI sunken box suitable for fixing switches, sockets and regulators including PVC insulated stranded copper conductor 1.5 sqmm (nominal area) single core cable as earth continuity conductor to common earth and connecting to earth dolly complete all as specified and directed for One 3 pin 5 Amp socket outlet point controlled by one switch on independent board. |
| 100 | M & L for point wiring with FRLSH stranded copper conductor 2.5 sqmm (nominal area), two single core, PVC insulated cable 1100 volts grade, ISI-694 marked in and including heavy duty, PVC Conduit including all accessories etc ISI marked, with GI sunken box suitable for fixing switches, sockets and regulators including PVC insulated stranded copper conductor 2.5 sqmm (nominal area) single core cable as earth continuity conductor to common earth and connecting to earth dolly complete all as specified and directed for 3 pin, 15 Amp socket outlet, independent |
| 101 | S&F switch piano flush type button single pole one way 5 Amps all as specified and directed. |
| 102 | S&F socket outlet 2 in 1, 3 pin 5 Amp flush type all as specified and directed. |
| 103 | S&F switch piano flush type button single pole one way 15 Amps all as specified and directed. |
| 104 | S&F Socket outlet 2 in 1, 3 pin, 5 and 15amp flush type all as specified and directed. |
| 105 | S&F ceiling rose surface bakelite with three terminals all as specified and directed |
| 106 | S&F ceiling fan regulator socketed, step type, flush type heavy duty suitable to work on 230 volts Ac supply complete all as specified. |
| 107 | M & L for submain wiring with two single core 4.0 sqmm PVC insulated unsheathed cable multi-strand copper conductor FRLSH drawn through and including PVC non metallic rigid PVC Conduit with all fittings and fixing accessories on roof, walls, ceiling etc including 1 x4.0 sqmm PVC insulated unsheathed multi strand copper conductor earth wire FRLSH connecting earth including cutting groove for concealed wiring, making good to disturb surface of wall/floor with cement mortar and finishes to match existing complete all as specified and directed. Note: Two run of single core cable, one run earth wire and one run PVC Conduit will be measured as one length. |
| 108 | M & L for submain wiring with two single core 6.0 sqmm PVC insulated unsheathed cable multi-strand copper conductor FRLSH drawn through and including PVC non metallic rigid Conduit conceled with all fittings and fixing accessories on roof, walls, ceiling etc including 1 x 6.0 sqmm PVC insulated unsheathed multi strand copper conductor earth wire FRLSH connecting earth including cutting groove for concealed wiring, making good to disturb surface of wall/floor with cement mortar and finishes to match existing complete all as specified and directed. Note: Two run of single core cable, one run earth wire and one run PVC Conduit will be measured as one length. |
| 109 | Supply & Fix LED betten plastic type fitting of capacity 20W, operating on 230V, 50Hz, AC Supply having luminous efficacy of not less than 125 lumens/watts, CCT 6500K, P.F>0.9, 2.5 KV surge protection, 4-feet long, housing made out of extruded alluminium with decorative end caps elegently designed complete all as specified. |
| 110 | S & F LED light fitting mirror type with high out put diffuser 2 feet, 10 watt 220 V AC decorative type with driver holder and LED lamp including connecting up with three core flexible copper conductor cable of suitable size complete all as specified and directed.. |
| 111 | S&F bldg security light, LED luminaire 30 watt made up of pressure die cast alluminium body with mid power LED as lighting sources and PC cover having Top opening separate driver compartment with IP66 protection and impact resistance of IK07 including fixing arrangements and taking down old rusted bracket fittings complete all as per directed by Engr- in – charge. |
| 112 | S&F Angle bracket 40mm dia for fixing building security light of 40mm dia of 1 mtr long bent to shape 45 degree for fixing of security light including MS clamps of suitable size including nuts, bolts complete all as specified and directed |
| 113 | S&F plastic body exhaust fan 250mm sweep complete with louvers shutter, voltage 230V, 50 Hz, RPM 1200, copper winding and connecting to ceiling rose with flexible copper cable including making holes on the wall and making good to the disturbed surfaces complete all as specified and as directed. |
| 114 | S&F Metal body exhaust fan 300 mm sweep complete with louvers shutter, voltage 230V, 50 Hz, RPM 1200, copper winding and connecting to ceiling rose with flexible copper cable including making holes on the wall and making good to the disturbed surfaces complete all as specified and as directed. |
| 115 | S&F BLDC ceiling fan 1200mm sweep complete with blades, down rods and accessories, 230 V, min air delivery 210 CFM with service value 6.00 BEE 5 star rated & provn of ‘S’ type fan hook including taking down of old UNSV one and depositing to MES storeyard for keeping in safe custody complete all as specified and directed including one step type electronic regulator. |
| 116 | S & F electric water heater, storage type steel body with copper inner tank and heating element upto 2 KW capacity 25 litre, BEE 5 Star rated complete with all accessories such as safety valve, thermostate, NRV, connection pipe etc complete all as specified and as directed. |
| 117 | S&F moduler type 3/5 pin socket with one single pole MCB 20Amp 230Volts including concealing in wall suitable for geyser, AC and domestic applianes complete all as specified and directed. |
| 118 | S&F factory made distribution Board sheet metal enclosure powder coated single phase neutral (SPN)DB for fixing of MCBs, 8 way double door with Aluminum bus bar 100 Amp including grouting on the wall by means of screws and rawal plugs and making good disturbed surfaces complete all as specified and directed. |
| 119 | S&F MCB SPN of capacity 40-63 Amps, 240 V, 10 KA 'C' curve complete all as specified and directed. |
| 120 | S&F MCB SP of capacity 5-32 Amps, 240 V, 10 KA 'C' curve complete all as specified and directed. |
| 121 | Taking out old existing earthing and M & L for new earthing with galvanised steel earth plate electrode 600mm X 600mm X 6mm thick burried directly in ground (earth pit not less than 2.25 mtr below ground level) with top edge of the plate not less than 1.5 mtr below ground level connected to 4mm dia GI wire protected by 20 mm bore light grade galvanised iron pipe and other end connected to test point as directed including funnel with wire mesh and watering pipe 20 mm bore medium grade galvanised iron pipe with charcoal and common salt in alternaterlayers of 15 cm thickness all around the GI plate electrode with concrete pit in PCC 1:3:6 type C-1 with cast iron frame including cast iron cover 10mm thick hinged to CI frame and 6mm MS rod for handle, necessary excavation and earth wok in hard/dense soil and disposal of spoil to a distance n exc 50 m and necessary testing complete all as shown in electrical plate No 3 of SSR part-I complete all as specified and directed. |
| 122 | S & F GI tube light grade 40mm bore with fittings for protection of cable complete all as specified and directed. |
| 123 | Supply, fixing, commissioning & testing of XLPE insulated, screened, PVC bedded, galvanised steel strip or wire armoured, Electric power cable (heavy duty) with aluminium conductors, cross sectional area 10 sqmm 2.0 core 1100 volts grade laid in trenches/fixed to wall/under road/pipe etc with copper cable glands & copper thimbles complete all as specified and directed. |
| 124 | Supply & laying GI tubes, 25mm medium grade,with screwed socket joint together with and including all Gl fittings connection on waal or floor with clamps digging etc as per site requirement as per Engr-in-Charge |
| 125 | S&F gun metal gate valve 25mm dia, cast copper alloy, screwed down high pressure with crutch or butterfly handle screwed both ends for iron pipe complete all as specified and directed. |
| 126 | M & L for cutting of existing GI pipe line 25mm dia for inserting Tee and reducer etc for taking 25mm dia branch pipe including fittings complete |
| 127 | M & L for plain cement concrete 1:3:6 type C-2 (using 40mm graded stone aggregates) with 100mm thick for flooring complete all as specified and dirceted |
| 128 | Excavation in trenches not exceeding 1.50 m wide and n.exc 1.5 m in depth for foundation of poles, cable etc, not exc 10 sqm on plan and getting out in soft/loose soil including taking out brick protection etc complete all as specified and directed. |
| 129 | Returning, filling in, including spreading, leveling, watering and well ramming in layers not exc 30cm thick complete all as specified and directed. |
| 130 | Removing excavated materials (soils) not exc. 50m and depositing where directed at a level not exc. 1.5m above the starting point complete all as specified and directed. |
| 131 | M & L for sand cushioning by spreading in trenches crushed sand by gently by punning down manually as in cable protection all as specified and as directed by Engineer -in-charge.Note : Thickness of sand cushioning after punning down will be measured. |
| 132 | M&L for bricks sub-class 'B' old size designation 75 of size 230X115X75mm laid in trenches for cable protection complete all as specified and directed. Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Sep 22, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedOct 14, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 21 daysOct 17, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 24 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender