Tender For Special Repairs To Toe Drain From Ls 1270M To 1800M In Irukkangudi Reservoir In Sattur Taluk Of Virudhunagar District.
Tender Value
Ref. Documents
Estimated cost
Bid Submission
05 Oct 2026
2 days left
EMD
3000
Bank guarantee accepted
Document Fee
Ref. Documents
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Virudhunagar → Tamil Nadu
EMD Exemption
Not Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender For Special Repairs To Toe Drain From Ls 1270M To 1800M In Irukkangudi Reservoir In Sattur Taluk Of Virudhunagar District.
BOQ
| Sl. No. | Item Description |
| 1 | Earthwork excavating and depositing bank with an Intial lead of 10m. And intial lift of 2m in Hard stiff clay, stiff black cotton soil, Hard red earth, shales , Murrams, stoney earth mixed with small sized boulders and other gravelly soils SS20B |
| 2 | Earth work excavation for foundation in all kinds of soil and subsoils except hard rock requiring blasting full depth as may be directed and depositing the surplus earth in places shown by the engineer in chareg of work and levelling the same with all leads and lifts including shoring, strutting, shuttering bailing out water wherever necessary and refilling the sides of foundation with excavated earth in layers of 15cm thick well rammed and consolidated, etc., complete complying with technical specifications and drawings as directed by the engineer in charge of work. |
| 3 | Supplying and erecting steel centering including necessary supports for plane surfaces for Reinforced Cement Concrete works such as column footings, column pedestals, plinth beams, grade beams, staircase steps, Sill slabs etc. which require only nominal strutting using mild steel sheets of size 90cm x 60cm and 10 BG stiffened with welded mild steel angles of size 25mm x 25mm x 3 mm for boarding, laid with silver oak joists of size 10cm x 5cm & 7.5cm x 5cm as support runner , vertical stiffener, side support and Top Horizontal stiffener spaced at about 60cm to 90cm centre to centre or at suitable intervals etc. complete in all floors complying with standard specifcation. (Payment for centering shall be given after the concrete is laid). |
| 4 | Providing and placing Plain Cement Concrete M 10 grade using well graded aggregates of nominal maximum size of 40mm and downgraded to I.S specified grading ( To achieve the specified charaterstics strength of 10N/mm² in 28 days ) and mixing the ingredients in approved mixer including dewatering of the placement site by bailling / pumbing and diverting wharever necessary, placing concrete in layers, compacting, watering, curing, finishing the surface with all leads and lifts etc., complete as directed by the Engineer in charge of works and as per the technical specifications. |
| 5 | Supplying and fixing New G.I pipe post using G.I pipe of approved quality and good variety ISI brand \\"B\\" class pipes of the following sizes for fencing post including cutting the pipe to required length fixing the pipe to plumb in the existing holes and laying the concrete. The rate is inclusive of cost of G.I pipes, including conveyance to work site and labour charges for cutting the pipe to required length and fixing in position as directed by the Departmental officers. etc., complete. (TNBP N. 86 ) 50 mm dia G.I pipe post. (M-0434 ) |
| 6 | Supplying and fixing new 6 mm thick M.S chain link fencing of approval gauge with angle above ground level and tying the same with an angle including the cost of MS flat making holes on the flat cost of bolt nut 40 nos washer etc to size of the chain link fenching is 2 \\" x 2\\" x 10 gauge |
| 7 | Manufacturing supplying and fixing of Fully Panelled steel door with the following specification MS angels of size 40x40x6mm are used for the outer frames and M.S. angles of size 35x35x5mm for the shutter frames, stiffeners with 32 x 6mm M.S flat is provided at required intervals in the shutter frame. 18-gauge C.R. sheet laid as panel in the shutter and welded intact. M.S. flat 18x5mm is welded over the 32 x 6mm M.S. flat sandwitching the C.R. sheet in between additional stiffeners with 18x5mm M.S. flat is provided diagonally at the rear side of the shutter. 3nos. of Steel Parliament Hinges of Size 125mm x 150mm in case of single leaf and 6nos. of Steel Parliament Hinges of Size 125mm x 150mm in double leaves shutter to be provided. 6nos. of holdfasts 200 mm in length made of angle section spliced at the ends are welded to the outer frames of the door. Tower bolts 3 nos, one at the top, one at lock rail(Inner) and the other at the bottom are provided 1no. Aldrop is provided at lock rail section in the door 2 Nos of 200mm handle are to be provided. One rotaing locking arrangements for the inner side of the door and additional provision for locking arrangements for lock is provided on the rear side of the door at an appropriate place. Incase of double leaf door M.S.Flat 32 x 3mm at 1.1Kg/m is provided on the one shutter t conceal the gap between the two shutters. at an appropriate place in the door. A tie bar is provided at the bottom of the frame to prevent twisting of frame during transportation and fixing. All members are given a coat of red oxide primer as directed by the departmental officers. The rate includes cost of all materials, labour charges, transportation to site of work, loading, un loading and all other incidental charges etc., complete complying with standard specification and as directed by the departmental officers. -Single leaf of size 1.00m x 2.10m. |
| 8 | Painting new iron works such as steel doors, windows, ventilators, window bars, balustrades etc., with two coats of best approved first quality and colour of synthetic enamel paint over the existing red oxide priming coat in all floors excluding cost of priming coat etc., complete complying with standard specification and as directed by the departmental officers. (The make, quality and colour of paint should be got approved by the Executive Engineer before use on works.) |
| 9 | Providing and placing Plain Cement Concrete M 15 grade using well graded aggregates of nominal maximum size of 20mm and downgraded to I.S specified grading ( To achieve the specified charaterstics strength of 15N/mm² in 28 days ) and mixing the ingredients in approved mixer including dewatering of the placement site by bailling / pumbing and diverting wharever necessary, placing concrete in layers, compacting, watering, curing, finishing the surface with all leads and lifts etc., complete as directed by the Engineer in charge of works and as per the technical specifications. |
| 10 | GST 18% in Figures Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Sep 21, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedOct 05, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 2 daysOct 06, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 3 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender