Tender For Special Repairs To Or Living Line Bldg No. P-45 At Otm Accn Of 322 Med Regt At Mil Stn Alwar.
Tender Value
44.41 Lakhs
Estimated cost
Bid Submission
13 Oct 2026
21 days left
EMD
89000
Bank guarantee accepted
Document Fee
500
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Alwar → Rajasthan
EMD Exemption
Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for Special Repairs To Or Living Line Bldg No. P-45 At Otm Accn Of 322 Med Regt At Mil Stn Alwar.
BOQ
| Sl. No. | Item Description |
| 1 | Demolition of cement concrete, unreinforced, of any description as in ground floors and paving, n exc 15 cm thick, below or above ground level, including breaking up and getting out, complete all as specified and directed. |
| 2 | Demolition of reinforced cement concrete of any description as in landing slabs, chullah hoods, manhole covers, roofs, floors, beams, staircases, landings, chajjas and similar suspended work, including cutting reinforcement where necessary and getting out, complete all as specified and directed. |
| 3 | Demolition of brickwork built in cement mortar or cement-lime mortar, including quoins and arches, complete all as specified and directed. |
| 4 | Taking down cement plaster/rendering of any description from brick, stone or cement concrete surfaces of walls and ceilings, including raking out joints/hacking surface for key and scrubbing down with water, complete all as specified and directed. |
| 5 | Taking down chowkhats/frames together with shutters, without taking shutters off frames, area n exc 1.50 Sqm each, complete all as specified and directed. |
| 6 | Taking down chowkhats/frames together with shutters, without taking shutters off frames, area exc 1.50 Sqm but n exc 4.00 Sqm each, complete all as specified and directed. |
| 7 | S&F in replacement 15 mm bore concealed galvanised iron tubing, medium grade, including all fittings such as bends, elbows, sockets, reducers, tees etc., fixed to walls/ceilings or laid in floors as required, including cutting/chasing through walls/floors and making good disturbed surfaces and taking down existing old U/S steel/GI tubing, fixed complete all as specified and directed. |
| 8 | All as per preceding GI tubing item but 20 mm bore. |
| 9 | M&L for post-construction anti-termite treatment to soil along external perimeter of building below concrete/masonry apron by injecting chemical emulsion at the rate of 2.25 litres per running metre, including drilling holes through apron at required spacing, injecting chemical emulsion and sealing/plugging holes with cement mortar 1:2, complete all as specified and directed. |
| 10 | M&L for brickwork with fly-ash bricks, old size, straight or curved on plan of mean radius exc 6 metre, built in cement mortar 1:6, including necessary scaffolding, raking out joints where required and curing, complete all as specified and directed. |
| 11 | M&L for half-brick thick brickwork with fly-ash bricks, straight or curved to any radius, built in cement mortar 1:4, including necessary reinforcement where specified separately, scaffolding and curing, complete all as specified and directed. |
| 12 | M&L for 15 mm thick rendering in cement mortar 1:4 on fair faces of brickwork/stone masonry, finished even and smooth without using extra cement, including mixing approved integral waterproofing compound at 3% by weight of cement, complete all as specified and directed. Note: Waterproofing compound shall be measured and paid for separately. |
| 13 | M&L for 15 mm thick rendering in cement mortar 1:6 on surfaces other than fair faces of brickwork/stone masonry, finished even and smooth without using extra cement, including scaffolding and curing, complete all as specified and directed. |
| 14 | M&L for 10 mm thick rendering in cement mortar 1:3 on ceiling surfaces, finished even and smooth without using extra cement, including scaffolding and curing, complete all as specified and directed. |
| 15 | M&L for 15 mm thick polymer-modified cement mortar plaster in proportion 1:3, fortified with SBR bonding/admixture compound, Nitobond SBR 45 or equivalent approved, using approximately 5 litres SBR for 50 Kg cement with water as recommended by manufacturer, applied to ceiling, beams and similar surfaces and finished to match adjoining existing surface, including taking down loose/U/S existing plaster, preparation and cleaning of substrate, application of bonding treatment, curing and making good, complete all as specified and directed. |
| 16 | M&L for rough-cast plaster to exterior walls comprising undercoat of cement mortar 1:3 n less than 10 mm thick and, while undercoat is in plastic state, application of rough-cast finishing mixture consisting of crushed stone/fine gravel aggregate of 6 to 12 mm size, coarse sand and cement in proportion 1:1:1, thoroughly mixed and applied uniformly to obtain even rough-cast finish, including preparation of surface, scaffolding and curing, complete all as specified and directed by Engineer-in-Charge. |
| 17 | S&F powder-coated aluminium openable window complete, outer frame comprising stiles, top, bottom and intermediate rails of hollow aluminium section 125 x 44 x 1.60 mm thick and openable glazed shutters fabricated from aluminium section 44 x 18 x 1.25 mm thick, glazed with 4.8 mm thick heat-absorbing glass securely fixed with suitable EPDM glazing beads, complete with handles, locking clips and necessary hardware; including openable gauze shutters fabricated from aluminium section 44 x 18 x 1.25 mm thick fitted with stainless steel wire cloth of 0.36 mm nominal wire diameter and average aperture 1.40 mm, securely fixed with suitable stainless steel screws/beading, handles and locking arrangement, including necessary cleats, fasteners, screws, sealant and all accessories, fixed complete all as specified and directed. Note: Outer overall size of completed window shall be measured for payment. |
| 18 | S&F powder-coated aluminium ventilator complete, outer frame comprising stiles, top, bottom and intermediate rails of hollow aluminium section 50 x 25 x 1.80 mm thick; lower portion glazed with 3 mm thick pin-headed glass securely fixed with aluminium glazing beads/clips and EPDM beading; upper portion provided with powder-coated aluminium louvre guides fitted with 3 mm thick pin-headed glass louvres, suitable EPDM beading, handles/clips and stainless steel wire cloth of 0.36 mm nominal wire diameter and average aperture 1.40 mm fixed in suitable frame, including necessary cleats, fasteners, screws, sealant and all accessories, fixed complete all as specified and directed. Note: Outer overall size of completed ventilator shall be measured for payment. |
| 19 | S&F stainless steel wire cloth having 0.36 mm nominal diameter wire and average width of aperture 1.40 mm, stretched taut and fixed to existing/new frames with stainless steel staples/screws as applicable, complete all as specified and directed. |
| 20 | S&F framework such as grills, gratings, framed guard bars, barred iron doors, ladders, balusters, walkways, railings, framework for water tanks and similar work, fabricated from structural steel conforming to Grade E-165 (Fe 290), with ends of bars shouldered/riveted or forged into spikes as required, including cutting, drilling, welding, riveting, bolts, nuts and fixing in position, complete all as specified and directed. |
| 21 | M&L for framed steelwork as in doors/gates, cooler stands and similar work fabricated from angles and other structural steel sections conforming to Grade E-165 (Fe 290), complete with gusset plates, rails and braces, drilled/prepared for fixing steel sheeting or other covering and prepared for hanging/sliding, including hooks and hinges or steel hanging-door fittings, fastening, fabrication, welding and fixing complete, but excluding steel sheeting/other covering, running rails and guides, complete all as specified and directed. |
| 22 | Cutting holes in stone walls built in cement mortar for inserting holdfasts and making good disturbed portions in cement mortar 1:3 or cement concrete 1:2:4 Type B-1, size exc half-brick but n exc one-brick, complete all as specified and directed. |
| 23 | S&F factory-made single-extruded WPC (Wood Polymer Composite) solid plain flush door shutter, 30 mm thick, comprising virgin polymer of K-value 58–60 suspension grade, calcium carbonate, natural fibres such as wood powder/rice husk/wheat husk and non-toxic additives, maximum toxicity index 12 per 100 g, minimum density 650 Kg/Cum, minimum screw withdrawal strength 1800 N on face and 900 N on edge, minimum compressive strength 50 N/Sqmm, modulus of elasticity n less than 850 N/Sqmm and resistance to spread of flame Class-A category, termite/borer proof, water/moisture proof and fire-retardant, fixed to frame with stainless steel butt hinges and full-body threaded star-headed countersunk stainless steel screws, complete all as specified and directed. Note: Stainless steel butt hinges and screws shall be measured and paid separately. |
| 24 | S&F factory-made single-extruded WPC solid door/window/clerestory window frame/chowkhat, section 45 x 70 mm, comprising virgin PVC polymer of K-value 58–60 suspension grade, calcium carbonate, natural fibres such as wood powder/rice husk/wheat husk and non-toxic additives, maximum toxicity index 12 per 100 g, fabricated with mitred joints using PVC solvent cement and full-body threaded star-headed stainless steel screws, minimum density 750 Kg/Cum, minimum screw withdrawal strength 2200 N on face and 1100 N on edge, minimum compressive strength 58 N/Sqmm, modulus of elasticity n less than 900 N/Sqmm and resistance to spread of flame Class-A category, termite/borer proof, water/moisture proof and fire-retardant, fixed in position with suitable MS holdfasts/lugs or stainless steel dash fasteners of required diameter and length, complete all as specified and directed. |
| 25 | S&F factory-made 35 mm thick second-class hardwood glazed/skeleton shutter, open rebated and prepared to receive wire mesh/gauze etc., without sash bars, edges of framing plain/chamfered/rounded and fitted with cut and mitred beads for securing wire mesh/glazing, sizes of members conforming to MES SSR Part-I Section 8 Clause 8.24(a), supplied and fitted to chowkhats, complete all as specified and directed. |
| 26 | S&F stainless steel butt hinges, 100 mm long, medium weight, including stainless steel screws, fixed complete all as specified and directed. |
| 27 | S&F anodised extruded aluminium alloy barrel tower bolt, 150 mm long, complete with barrel, bolt, staple/keeper and fixing screws, fixed complete all as specified and directed. |
| 28 | S&F extruded aluminium alloy handle, 150 mm long, fabricated and anodised type, ISI marked where applicable, including fixing screws, fixed complete all as specified and directed. |
| 29 | S&F aluminium alloy floor door stopper, 150 mm overall length, comprising anodised aluminium alloy body and tongue with hard-drawn steel spring and necessary fixing screws, fixed complete all as specified and directed. |
| 30 | S&F anodised aluminium alloy sliding door bolt, 300 mm long, complete with hasp and staple, fixing clips, bolts and sliding bolt fabricated from extruded/cast aluminium alloy sections, fixed complete all as specified and directed. |
| 31 | S&F stainless steel curtain rod, 25 mm dia, with designer/fancy end knobs and matching stainless steel brackets, including screws, fasteners and all accessories, fixed complete all as specified and directed. |
| 32 | Taking down existing old roof treatment, including carefully removing loose/U/S treatment, cleaning roof surface thoroughly by wire brushing and washing/watering and applying cement slurry at the rate of 3 Kg cement per Sqm over prepared roof surface, complete all as specified and directed. |
| 33 | M&L for PCC 1:2:4 Type B-0 using 12.5 mm graded crushed stone aggregate as in roof padding/levelling course, laid to minimum consolidated thickness 25 mm and formed to minimum slope 1 in 30, including necessary formwork, laying, compacting, finishing and curing, complete all as specified and directed. |
| 34 | M&L for 15 mm thick rendering in cement mortar 1:4 on roof slab, mixed with approved waterproofing compound at 3% by weight of cement, finished even and smooth to required slope for receiving APP modified bituminous membrane, including preparation and curing, complete all as specified and directed. Note: APP membrane and waterproofing compound shall be measured and paid separately. |
| 35 | M&L for four-course waterproofing treatment with APP modified bituminous waterproofing membrane, polyester reinforced, plain finish, 3 mm thick and total finished membrane weight n less than 3 Kg/Sqm ±5%, conforming to IS 16532:2017, comprising first course of bitumen primer conforming to IS 3384 at 0.40 litre/Sqm, second and fourth courses of bonding material comprising industrial bitumen Grade 85/25 conforming to IS 702 at 1.20 Kg/Sqm for each course and third course of APP membrane, laid by torch application, including sealing all joints with side laps n less than 75 mm and end laps n less than 100 mm, dressing at upstands, outlets and penetrations and sealing all overlaps by torch application, complete all as specified and directed. |
| 36 | M&L for applying two coats of heat-reflective silver aluminium paint over prepared APP modified bituminous membrane, including cleaning surface between coats and finishing uniformly, complete all as specified and directed. |
| 37 | Supply only approved integral waterproofing compound suitable for cement concrete/cement mortar, conforming to applicable IS and manufacturer's recommendations, complete all as specified and directed. Please Enable Macros to View BoQ information |
| 38 | Supply only approved integral waterproofing compound suitable for cement concrete/cement mortar, conforming to applicable IS and manufacturer's recommendations, complete all as specified and directed. Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Sep 21, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedOct 13, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 21 daysOct 15, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 23 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender