Tender For Redevelopment Of Geetanjali Lodge At Agartala
Tender Value
Ref. Documents
Estimated cost
Bid Submission
12 Oct 2026
4 days left
EMD
30.73 Lakhs
Bank guarantee accepted
Document Fee
20000
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
tripura → Tripura
EMD Exemption
Not Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for Redevelopment Of Geetanjali Lodge At Agartala
BOQ
| Sl. No. | Item Description |
| 1 | Bill No. I: Earthwork Work |
| 2 | Clearing grass and removal of the rubbish upto a distance of 50 m outside the periphery of the area cleared. |
| 3 | Surface dressing of the ground including removing vegetation and in equalities not exceeding 15 cm deep and disposal of rubbish, lead upto 50 m and lift upto 1.5 m. - All kinds of soil |
| 4 | Earth work in excavation by mechanical means (Hydraulic excavator) / manual means over areas (exceeding 30cm in depth, 1.5m in width as well as 10 sqm on plan) including disposal of excavated earth, lead upto 50m and lift upto 1.5m, disposed earth to be levelled and neatly dressed. |
| 5 | Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift upto 1.5 m.All kinds of soil |
| 6 | Supplying and filling in plinth, under floor, foundations etc. with sand (fine) from local quarry with all lifts including spreading in horizontal layers, watering, grading to required slope, ramming, consolidating and compacting each layer by using plate compactor or by any suitable method complete. |
| 7 | Supplying chemical emulsion in sealed containers including delivery as specified.Chlorpyriphos/Lindane emulsifiable concentrate of 20% |
| 8 | Diluting and injecting chemical emulsion for POSTCONSTRUCTIONALanti-termite treatment as per IS: 6313(Part III)- Latest revision (excluding the cost of chemical emulsion):Along external wall where the apron is not provided using chemical emulsion @ 7.5 litres/sqm of the vertical surfaceof the substructure to a depth of 300 mm including excavation channel along the wall & rodding etc. complete:With Chlorpyriphos/Lindane E.C. 20% with 1% concentration. |
| 9 | Along the external wall below concrete or masonry apron using chemical emulsion @ 2.25 litres per linear metre including drilling and plugging holes etc.With Chlorpyriphos/Lindane E.C. 20% with 1% concentration. |
| 10 | Treatment of soil under plinth filling using chemical emulsion @ one litre per hole, 300 mm apart includingdrilling 12 mm diameter holes and plugging with sand filling: With Chlorpyriphos/Lindane E.C. 20% with 1% concentration. |
| 11 | Treatment of soil under existing floors using chemical emulsion @ one litre per hole, 300 mm apart including drilling 12 mm diameter holes and plugging with cement mortar 1 :2 (1 cement : 2 fine sand) to match the existing floor:With Chlorpyriphos/Lindane E.C. 20% with 1% concentration. |
| 12 | Treatment of existing masonry using chemical emulsion @ one litre per hole at 300 mm interval including drilling holes at 45° and plugging them with cement mortar 1:2 (1 cement: 2 fine sand) to the full depth of the hole:With Chlorpyriphos/Lindane E.C. 20% with 1% concentration. |
| 13 | Treatment at points of contact of wood work by chemicalemulsion Chlorpyriphos/ Lindane (in oil or kerosene basedsolution) @ 0.5 litres per hole by drilling 6 mm dia holes atdownward angle of 45° at 150 mm centre to centre andsealing the same.The work will be carried out as per IS: 6313 [Latest Revision]. Under the Insecticides Rule 1971: 10(3A) any person who desiresto undertake pest control operations will be a Licence holder.The agency must complying with all safety health and welfareregulations, appertaining to staff and work people employed onthe site.Keeping the site free from debris arising from the works duringthe work and leave the site free from debris on completion of work to the satisfaction of the Owner.The agency shall give a 3-year service guarntee in writingsupplemented by a seperate and unilateral guarantee from the specialised agency for the job to keep the building free of termites for the specified period at no extra cost of the Owner |
| 14 | Bill No. II: Cement Concrete Work |
| 15 | Providing and laying in position cement concrete of specified grade excluding the cost of centring and shuttering - All Work upto Plinth Level:1:2:4 ( 1 Cement: 2 fine sand : 4 graded stone aggregate 20 mm nominal size) |
| 16 | Providing and laying damp-proof course with cement concrete 1:2:4 (1 cement: 2 coarse sand : 4 graded stone aggregate 12.5mm nominal size).DPC 40 mm thick |
| 17 | Providing & applying a coat of residual petroleum bitumen of grade of VG-10 of aproved quality using 1.7kg per square metre on damp proof course after cleaning the surface with brushes and finally with a piece of cloth lightly soaked in kerosene oil. |
| 18 | Making plinth protection 50mm thick of cement concrete 1:3:6 (1 cement : 3 fine sand : 6 graded well burnt brick aggregate 20 mm nominal size) over 75mm bed of dry brick ballast 40mm nominal size well rammed and consolidated and grouted with fine sand including finishing the top smooth. |
| 19 | Making plinth protection 50mm thick of cement concrete 1:3:6 (1 cement : 3 fine sand : 6 graded well burnt brick aggregate 20 mm nominal size) over 75mm bed of dry brick ballast 40mm nominal size well rammed and consolidated and grouted with fine sand including finishing the top smooth. |
| 20 | Bill No. III: Reinforced Cement Concrete Work |
| 21 | Providing and laying in position specified grade of reinforced cement concrete excluding the cost of centring, shuttering, finishing and reinforcement-All Work upto Plinth Level:1:1½:3 ( 1 Cement: 1½ fine sand : 3 graded stone aggregate 20 mm nominal size) |
| 22 | Reinforced cement concrete work in walls (any thickness), including attached pilasters, buttresses, plinth and skirting courses, fillets, columns, pillars, piers, abutments, posts and struts etc. upto floor five level excluding cost of centring, shuttering, finishing and reinforcement-1:1½:3 ( 1 Cement: 1½ fine sand : 3 graded stone aggregate 20 mm nominal size) |
| 23 | Reinforced cement concrete work in beams, suspended floors, roofs having slope upto 15° landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases upto floor five level excluding the cost of centring, shuttering, finishing and reinforcement.1:1½:3 ( 1 Cement: 1½ fine sand : 3 graded stone aggregate 20 mm nominal size) |
| 24 | Providing and laying in position design mix cement concrete of specified grade for reinforced cement concrete work including pumping of concrete to site oflaying but excluding the cost of centring, shuttering, finishing and reinforcement, including admixtures in recommended proportions as per IS 9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability as per the directionof Engineer-in-Charge.(Note :- Cement content considered in this item is @418 kg/cum. Excess/ less cement used as per designmix is payable/recoverable separately).All works upto plinth levelReinforced cement concrete grade M-25 using 418 kg of cement per cum |
| 25 | All works upto Floor five levelReinforced cement concrete grade M-25 using 418 kg of cement per cum |
| 26 | Centering, Shuttering including struttings, propping etc and removal of form work for:Foundations, footings, bases for columns etc. for mass concrete with timber plank |
| 27 | Foundations, footings, bases for columns etc. for mass concrete with steel formwork |
| 28 | Suspended floors, roofs, landings, balconies and access platform with timber planks |
| 29 | Suspended floors, roofs, landings, balconies and access platform with M.S. plates and props |
| 30 | Lintel beams, plinth beams, girders, bressumers & cantilevers with 12 mm shuttering ply |
| 31 | Columns, Pillars, Piers, Abutments, Posts and Struts with M.S. shutters |
| 32 | Stairs (excluding landings) except spiral-staircases with wooden plank |
| 33 | Extra for additional height in centring, shuttering where ever required with adequate bracing, propping etc. including cost of de-shuttering and decentring at all levels, over a height of 3.5 m, for every additional height of 1 metre or part thereof: Suspended floors, roofs, landing, beams and balconies (Plan area to be measured). |
| 34 | Reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto plinth level.Thermo-Mechanically Treated bars of grade Fe-500D or more |
| 35 | Bill No. IV: Brick Work |
| 36 | First class brick work in foundation and plinth including cost of all materials as required complete:-In cement mortar 1:4 ( 1 cement : 4 fine sand ). |
| 37 | First class brick work in superstructure above plinth level & upto floor-five level including cost of all materials as required complete:-In cement mortar 1:4 ( 1 cement : 4 fine sand ). |
| 38 | Half brick masonry work with first class bricks in superstructure upto floor five level including cost of all materials as required complete:-In cement mortar 1:4 ( 1 cement : 4 fine sand ). |
| 39 | Providing and fixing Galvanized chicken mesh (24 guage, 12 mm size) properly stretched and nailed ensuring equal thickness of plaster at junction of masonry work and concrete members. |
| 40 | Bill No. V: Wood Work & PVC |
| 41 | Providing wood work in frames of doors, windows,clerestory windows and other frames, wrought framedand fixed in position : - Karai wood |
| 42 | Providing and fixing panelled / or panelled and glazed shutters for doors, windows and clerestory/ windows including ISI marked bright finished / black enamelled M.S butt hinges with necessary screws excluding panelling and or glazing, which will be paid for separately but including the wooden beading of 20 × 12 mm for fixing panelling and or glazing as per direction of Engineer-In-Charge.Local Teak wood35 mm thick shutters |
| 43 | Providing and fixing 35 mm thick factory made laminated veneer lumber door shutter conforming to IS : 14616 and TADS 15:2001 (Part B) including ISI marked black enamelled M.S. butt hinges with necessary screws as per directions of Engineer-incharge and panelling with panels of:12 mm thick one side prelaminated (with particle board decorative lamination on other sides) and balancing lamination grade - 1 medium density flat pressed, three layer particle board FPT - I or graded wood particle board FPT-1 conforming to IS : 3087 bonded with BWP type synthetic resin adhesive as per IS : 848 and prelamination conforming to IS : 12823 Grade - 1, Type II marked : |
| 44 | Providing and fixing aluminium handles ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade with necessary screws etc. complete : - 125 mm |
| 45 | Providing and fixing factory made UPVC door frame made of UPVC extruded, section having an overall dimension, as below (tolerance +/- 1mm) with wall thickness 2.0mm+/- 02mm. corners of the door frame to be jointed with galvanized brackets and stainless screws, joint mitred and plastic wilded. The hinge side vertical of the frames reinforced by galvanized MS tube of size 19 × 19 mm and 1 mm +/- 0.1 mm wall thickness and 3 nos stainless steel hinges fixed to the frame complete as per manufacturers specification and direction of Engineer-In-Charge.Extruded section Profile size 48x40 mm. |
| 46 | Providing and fixing to existing door frames.24 mm thick factory made PVC door shutters made of styles and rails of a UPVC hollow section of size 59x24 mm and wall thickness 2 mm ± 0.2 mm with inbuilt edging on both sides. The styles and rails mitred and joined at the corners by means of M.S. galvanised /plastic brackets of size 75×220 mm having wall thickness 1.0 mm and stainless steel screws. The styles of the shutter reinforced by inserying galvanised MS tube of size 20×20 mm and 1 mm ± 0.1 mm wall thickness. The lock rail made up of \\"H\\" Section, a UPVC hollow section of size 100×24 mm and 2 mm ± 0.2 mm wall thickness fixed to the shutter styles by means of plastic /galvanised MS \\"U\\" cleats. The shutter frame filled with a UPVC multi-chambered single panel of size not less than 620 mm, having overall thickness of 20 mm and 1 mm ± 0.1 mm wall thickness. The panels filled vertically and tie bar at two places by inserting horizontaly 6 mm galvanised MS rod and fastened with nuts and washers, complete as per manufacturer's specification and direction of Engineer-In-Charge. (for W.C. and Bathroom door shutter). |
| 47 | Providing and fixing factory made P.V.C. door frame of size 50x47 mm with a wall thickness of 5mm, made out of extruded 5mm rigid PVC foam sheet mitred at corners and joined with 2 Nos. of 150mm long brackets of 15x15mm M.S. square tube, the vertical door profiles to be reinforced with 19×19mm MS square tube of 19 gauge, EPDM rubber gasket weather seal to be provided through out the frame . The door frame to be fixed to the wall usuing MS screws of 65/100 mm size complete as per manufacturers' specification and direction of Engineer-In-Charge. |
| 48 | Providing and fixing curtain rods of 1.25 mm thickchromium plated brass plate, with two chromiumplated brass brackets fixed with C.P. brass screws andwooden plugs, etc., wherever necessary complete : - 20 mm dia |
| 49 | Providing and fixing M.S. grills of required pattern inframes of windows etc. with M.S. flats, square orround bars etc. all complete.Fixed to steel windows by welding. |
| 50 | Fixed to openings /wooden frames with rawl plugs screws etc. |
| 51 | providing 40 × 5 mm flat iron hold fast 40 cm longincluding fixing to frame with 10 mm diameter bolts,nuts and wooden plugs and embedding in cementconcrete block 30 × 10 × 15 cm 1:3:6 mix (1 cement : 3fine sand : 6 graded stone aggregate 20mm nominalsize) |
| 52 | Providing and fixing ISI marked M.S. pressed butt hinges bright finished with necessary screws etc. complete :125 × 65 × 2.12 mm |
| 53 | 100 × 58 × 1.90 mm |
| 54 | 75 × 47 × 1.70 mm |
| 55 | 50 × 37 × 1.50 mm |
| 56 | Providing and fixing IS : 12817 marked stainless steel butt hinges with stainless steel screws etc. complete :125 x 64 x 1.90 mm |
| 57 | 100 X 58 X 1.90 mm |
| 58 | 75 x 47 x 1.80 mm |
| 59 | Providing and fixing bright finished brass towerbolts (barrel type)with necessary screws etc. complete :250x10 mm |
| 60 | 200 x 10 mm |
| 61 | 150 x 10 mm |
| 62 | Providing and fixing oxidised M.S. Safety chain with necessary fixtures for doors. (Weighing not less than 450 gms.) |
| 63 | Providing and fixing chromium plated brass handles with necessary screws etc. complete:125 mm |
| 64 | 100 mm |
| 65 | Providing and fixing bright finished brass hanging type floor door stopper with necessary screws, etc. complete. |
| 66 | Providing and fixing IS : 3564 marked aluminium extruded section body tubular type universal hydraulic door closer with double speed adjustment with necessary accessories and screws etc. complete. |
| 67 | Providing and fixing bright finished brass 100 mm mortice latch and lock ISI marked with six levers and a pair of anodised (anodic coating not less than grade AC 10 as per IS : 1868) aluminium lever handles with necessary screws etc. complete (Best make of approved quality) |
| 68 | Supplying and fixing rolling shutters of approved make,made of required size M.S. laths interlocked togetherthrough their entire length and jointed together at theend by end locks mounted on specially designed pipeshaft with brackets, side guides and arrangements forinside and outside locking with push and pull operation complete including the cost of providing and fixing necessary 275mm long wire springs grade No.2 and M.S.top cover of required thickness for rolling shutters &with handles, hold fast including embedding in cement concrete of required grade required for fixing in position, all necessary fittings, including applying of approvedsteel primer etc. complete as required:-80xl.25mm M.S. laths with 1.25 mm thick top cover. |
| 69 | Providing and fixing ball bearing for rolling shutters (exceeding 10 sqm area) of approved make complete as required. |
| 70 | Extra for providing & fixing mechanical device chain and crank operation for operating rolling shutters of approved make complete as required:-Exceeding 16.80 sqm in area. |
| 71 | Extra for providing & fixing grilled rolling shutters manufactured out of 8 mm dia. M.S. plain bar instead of laths as per design approved by Engineer-in-charge (area of grill to be measured) complete as required. |
| 72 | Providing and fixing aluminium tubular handle bar of 32 mm outer dia, 3.0 mm thick and 2100 mm long with Stainless Steel screws etc. of approved quality complete as per direction of Engineer-in-charge:-Polyester powder coated aluminium minimum thickness 50 micron. |
| 73 | Bill No. VI: Aluminium Work & Structural Glazing |
| 74 | Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS : 1285, fixing with dash fasteners of required dia and size, including necessary filling up of gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, aluminium snap beading for glazing / paneling, C.P. brass / stainless steel screws, all complete as per architectural drawing and the direction of Engineerincharge. (Glazing and paneling and dash fasteners to be paid for separately) :-For fixed portion of approved quality:-Powder coated aluminium ( minimum thickness of powder coating of 50 micron ). |
| 75 | For shutters of doors, windows & ventilators including providing and fixing hinges / pivots and making provision for fixing fittings wherever required including the cost of EPDM rubber / neoprene gasket required ( Fittings shall be paid for separately ):-Powder coated aluminium ( minimum thickness of powder coating of 50 micron ). |
| 76 | Providing and fixing double glazed hermetically sealed glazing in aluminium windows, ventilators and partition etc. with 6 mm thick clear float glass both side having 12 mm air gap including providing EPDM gasket, perforated aluminium spacers, desiccants, sealant (both primary and secondary sealant) of approved quality etc.complete as per specification, drawing and direction of Engineer-incharge |
| 77 | Providing and fixing aluminium round shape handle of outer dia 100 mm with SS screws etc. of approved quality complete as per direction of Engineer-in-charge:-Polyester powder coated aluminium minimum thickness 50 micron. |
| 78 | Providing and fixing 12 mm thick frameless toughenedglass door shutter of approved brand and manufacture,including providing and fixing top & bottom pivot &spring type fixing arrangement and making necessaryholes etc. for fixing required door fittings, all complete asper direction of Engineer-in-charge (Door handle, lockand stopper etc.to be paid separately). |
| 79 | Float glass sheet of nominal thickness 8 mm.(weight not less than 20 kg/sqm). |
| 80 | Float glass sheet of nominal thickness 4 mm (weight not less than 10kg/sqm). |
| 81 | Float glass sheet of nominal thickness 5.5 mm.(weight not less than 13.50 kg/sqm). |
| 82 | Frosted glass sheet of nominal thickness 4 mm (weighing not less than 10 kg/sqm) |
| 83 | Glass sheet (Pin headed) 4 mm thick |
| 84 | Toughened glass 12 mm thickness |
| 85 | Filling the gap in between aluminium frame and adjacent RCC/brick work by providing weather silicon sealantover backer rod of approved quality etc. complete as perarchitectural drawing and direction of the Engineer-incharge:- (i) Upto 5 mm depth and 5 mm width. |
| 86 | Bill No. VII: Flooring |
| 87 | Providing and laying 1st class quality ceramic floor tilesin different sizes (thickness to be specified by themanufacturer) of 1st quality conforming to IS : 15622 -2017 of approved make in colours such as White, Ivory,Grey, Fume Red Brown, laid over 20 mm thick cement mortar 1:4 (1 cement : 4 fine sand), Jointing with greycement slurry @ 3.3 kg/sqm including pointing the jointswith white cement and matching pigment etc. allcomplete as per direction of the Engineer in-charge.Mat Finish Tiles/ Anti-skid Tiles/ Glossy Tiles300 x 300mm in all shades and designs |
| 88 | 600 mm x 600 mm in all shades and designs 1st class quality ceramic floor Porcelain tiles |
| 89 | Providing and laying 1st class quality vitrified floor tilesin different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS: 15622 - 2017, of approved make, in all colours and shades, laid over 20mm thick cement mortar1:4 (1 cement : 4 fine sand), jointing with grey cementslurry @ 3.3 kg/ sqm including grouting the joints with white cement and matching pigments etc. all complete asper direction of the Engineer-in-charge..Double charged Stainfree vitrified tiles (Glossy)Size of tile 600 mm x 600 mm |
| 90 | Providing and fixing 1st class quality ceramic glazed wall tiles conforming to IS : 15622 - 2017 (thickness to be specified by the manufacturer) of approved make in all colours, shades of any size as approved by Engineer-incharge in skirting, risers of steps and dados, laid over 12 mm thick bed of cement mortar 1 : 3 (1 cement : 3 fine sand) jointed with ordinary cement slurry including pointing with white cement mixed with pigment of matching shade etc. all complete as per direction of the Engineer in-charge.450 mm X 300 mm in all shades and design |
| 91 | Providing and fixing coloured self adhesive PU - Tactile tiles, ground surface indicators (made of Polyurethane) grade 70/85 of size 300x300mm. for guiding/warning to the visualy impaired visitors in the entre/side of the pedestrian/ approch pathway as per design/specification and Harmonised guidelines complete in all respect as per the direction of the Engineer-in-charge. |
| 92 | Providing and laying flamed finish Granite stone flooring in required design and patterns, in linearas well as curvilinear portions of the building allcomplete as per the architectural drawings with Flamed finish granite stone slab Jet Black, Cherry Red, Elite Brown, Cat Eye or equivalent over 20mm (average) thick base of cement mortar 1:4 (1cement : 4 fine sand) laid and jointed with cement slurry and pointing with white cement slurry admixed with pigment of matching shade including rubbing, curing and polishing etc. allcomplete as specified and as directed by theEngineer-in-Charge-18 mm thick stone slab. |
| 93 | Providing & fixing in position Phenol bondedBamboowood flooring with planks of sizes 14mm thick, 1800mm length (minimum) and 130 mm wide (minimum),in approved colour, texture and finish, having Performance Appraisal Certificate (PAC) issued by Building Materials & Technology Promotion Council (BMTPC). The flooring shall be fixed with tongue andgroove interlocking system, with underlayment of 4mm thick expanded poly ethylene foam sheets having density 40kg/cum, over prepared surface with necessary quarter round planks of size 1900mm x 18mm and doorreducer of size 1900mm x 44mm, wherever required.The bomboo wood planks shall have minimum densityof 1000 Kg/cum & minimum Hardness 1000 Kgf. withEco friendly UV coating, etc. all complete as per directionof Engineer-in-charge. |
| 94 | Supply & installation of EPDM flooring |
| 95 | 40 mm thick fine dressed stone flooring over 20 mm (average) thick base of cement mortar 1:5 (1 cement : 5 coarse sand), including pointing with cement mortar 1:2 (1 cement : 2 stone dust) with an admixture of pigment to match the shade of stone. Red sand stone |
| 96 | Bill No. VIII:ROOFING |
| 97 | Supply & installation of pre-painted Galvalume sheetsfor roofing / cladding (size, shape and pitch of corrugation as approved by Engineer-in-charge) in 550 mpa steel grade, made out of Cold Rolled Steel coated with Zinc-Aluminium alloy coating of 43.5% Zn,55% Al and 1.5% Silicon confirming to ASTMA792/A792M and AS1397, Alloy coating AZ150/AZ70, colour coated with high quality Polyester coating, top coated of modified polyester of 20 micron, back side coat of 5 micron, having epoxy primer coat of 5 micron on both side. Sheet should have protective guard filmof 25 microns minimum to avoid scratches while transportation and should be supplied in single length upto 12 metre or as desired by Engineer-incharge.The sheet shall be fixed using self drilling / self tapping screws of size (5.5x 55mm) with EPDM washers filled with white lead complete upto anypitch in horizontal / vertical or curved surfaces excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required and as per direction of Engineer-in-charge.0.80mm thickness |
| 98 | Supply & installation of pre-painted Galvalume sheets roofing accessories in 550mpa steel steel grade, madeout of Cold rolled steel coated with Zinc-Aluminiumalloy coating of 43.5% Zn, 55% Al and 1.5% Silicon confirming to AASTM A792/A792M and AS1397, Alloy coating AZ150/AZ70, colour coated with high quality polyester coating, top coated of modified polyester of 20 micron, back side coat of 5 micron, having epoxy primercoat of 5 micron on both side etc. complete as perdirection of Engineer-in-charge. Sheet should have protective guard film of 25 microns minimum to avoid scratches while transportation. Sheet should have protective guard film of 25 microns minimum to avoid scratches while transportation. The sheetshall be fixed using self drilling /self tapping screws with EPDM washers complete for Ridges / Valley / Gutter / Flashing of width 610mm:0.80mm thickness |
| 99 | Providing and fixing false ceiling at all height including providing and fixing of frame work made of special sections, power pressed from M.S. sheets and galvanized with zinc coating of 120 gms/sqm (both side inclusive) asper IS : 277 and consisting of angle cleats of size 25 mmwide x 1.6 mm thick with flanges of 27 mm and 37mm, at 1200 mm centre to centre, one flange fixed to the ceiling with dash fastener 12.5 mm dia x 50mm long with 6mmdia bolts, other flange of cleat fixed to the angle hangers of25x10x0.50 mm of required length with nuts & bolts of required size and other end of angle hanger fixed with intermediate G.I. channels 45x15x0.9 mm running at the spacing of 1200 mm centre to centre, to which the ceiling section 0.5 mm thick bottom wedge of 80 mm with tapered flanges of 26 mm each having lips of 10.5 mm, at 450 mm centre to centre, shall be fixed in a direction perpendicular to G.I. intermediate channel with connecting clips madeout of 2.64 mm dia x 230 mm long G.I. wire at every junction, including fixing perimeter channels 0.5 mm thick27 mm high having flanges of 20 mm and 30 mm long, the perimeter of ceiling fixed to wall /partition with the help of rawl plugs at 450 mm centre, with 25mm long dry wall screws @ 230 mm interval, including fixing of gypsum board to ceiling section and perimeter channel with the help of dry wall screws of size 3.5 x 25 mm at 230 mm c/c,including jointing and finishing to a flush finish of tapered and square edges of the board with recommended jointing compound, jointing tapes, finishing with jointing compound in 3 layers covering upto150 mm on both sides of joint and two coats of primer suitable for board, all as per manufacturer's specification and also including the cost of making openings for lightfittings, grills, diffusers, cutouts made with frame of perimeter channels suitably fixed, all complete as per drawings, specification and direction of the Engineer in Charge but excluding the cost of painting with :12.5 mm thick tapered edge gypsum moisture resistant board |
| 100 | Providing and fixing false ceiling of Phenol bonded Bamboo wood ceiling (made in India) with planks of sizes8mm thick, 1800mm length (minimum) and 130mm wide (minimum), in approved colour, texture and finish, having Performance Appraisal Certificate (PAC) issued by Building Materials & Technology Promotion Council (BMTPC) The Bamboo wood planks shall have minimum density of 1000 Kg/cum & minimum Hardness 1000 Kgf. Eco friendly UV Coated factory finished Ceiling tiles with providing and fixing of framework made of special sections, power pressed from M.S. sheets and galvanized with zinc coating of 120gms/sqm (both side inclusive) as per IS : 277 and consisting of angle cleats of size 25 mm wide x 1.6 mm thick with flanges of 27mm and 37mm, at 600 mm Centre to Centre, one flange fixed to the ceiling with dash fastener 12.5mm dia x 50mm long with 6mm dia bolts, other flange of cleat fixed to the angle hangers of25x10x0.50 mm of required length with nuts & bolts of required size and other end of angle hanger fixed with intermediate G.I. channels 45x15x0.9 mm running at the spacing of 600 mm Centre to Centre, to which the ceiling section 0.5 mm thick bottom wedge of 80 mm with tapered flanges of 26 mm each having lips of 10.5mm, at 300 mm Centre to Centre, shall be fixed in a direction perpendicular to G.I. intermediate channel with connecting clips made out of 2.64 mm dia x 230 mm long G.I. wire at every junction, including fixing perimeter channels 0.5 mm thick 27 mm high having flanges of 20mm and 30 mm long, the perimeter of ceiling fixed to wall/partition with the help of rawl plugs at 450 mm Centre, with 25mm long dry wall screws at 230 mm interval, including fixing of ISI mark BWR plywood of 12mm thickness to ceiling section and perimeter channel with the help of dry wall screws of size 3.5 x 25 mm at 230 mm c/c, including jointing and finishing to a flush finish of tapered and square edges of the board with recommended jointing compound ,jointing tapes. All as per manufacturer's specification and also including the cost of making openings for light fittings, grills, diffusers, cutouts made with frame of perimeter channels suitably fixed, all complete as per drawings, specification and direction of the Engineer in Charge: |
| 101 | Supply and Installation of Tensile Walkway Canopy in fabricated MS structureas as per specification and approval of Engineer-in-Charge |
| 102 | Bill No. IX: Steel Work |
| 103 | Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete.Hot finished seamless type tubes |
| 104 | Providing structural steel work riveted, bolted or welded in built up sections, trusses and framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete as required. |
| 105 | Steel work welded in built up section/framed work including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using steel etc. complete as required:-In grating, frames, guard bar, railing, brackets, gates and similar works, all complete.In grating, frames, guard bar, railing, brackets, gates and similar works, all complete. |
| 106 | Bill No. X: Finishing Work |
| 107 | 12 mm Cement PlasterCement mortar 1:4 (1 cement : 4 fine sand) |
| 108 | 15 mm cement plaster on the rough side of single or half brick wall of mix:Cement mortar 1:4 (1 cement : 4 fine sand) |
| 109 | 6 mm cement plaster of mix :Cement mortar 1:4 (1 cement : 4 fine sand) |
| 110 | Neat cement punning. |
| 111 | 6 mm cement plaster in single layer finished with a floating coat of neat cement, curing and a thick coat of lime wash on top when dry on wall bearings for RCC slabs and beams complete.Cement mortar 1:3 (1 cement : 3 fine sand) |
| 112 | Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete. |
| 113 | Distempering with 1st quality acrylic distemper (readymixed) having VOC content less than 50 grams/ litre, ofapproved brand and manufacture to give an even shade[Payment shall be made after submission of TestCertificate issued by the Manufacturer] :New work ( two or more coats) over and including water thinnable priming coat with cement primer. |
| 114 | Wall painting with acrylic plastic emulsion paint of approved brand and manufacture to give an even shade [Payment shall be made after submission of Test Certificate issued by the Manufacturer] : Two or more coats on new work |
| 115 | Finishing walls with textured exterior paint of required shade of approved brand and manufacture [Payment shall be made after submission of Test Certificate issued by the Manufacturer] :New work ( two or more coats applied @ 3.28 litre/10 sqm) over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm |
| 116 | Applying one coat of water thinnable cement primer of approved brand and manufacturer on wall surface complete.Water thinnable cement primer |
| 117 | Applying priming coat [Payment shall be made after submission of Test Certificate issued by the Manufacturer] :With ready mixed Pink or Grey primer of approved brand and manufacture on wood work ( hard & soft wood ). |
| 118 | Painting with synthetic enamel paint of approved brand and manufacture to give an even shade [Payment shall be made after submission of Test Certificate issued by the Manufacturer]:Two or more coats on new work over an under coat of suitable shade with ordinary paint (primer) of approved brand and manufacture |
| 119 | Providing & fixing in position Phenol bondedBamboowood wall cladding at all height with planks ofsizes 10mm thick, 1800mm length (minimum) and 100mm wide (minimum), in approved colour, texture andfinish, having Performance Appraisal Certificate (PAC)issued by Building Materials & Technology PromotionCouncil (BMTPC), with necesasary profiled edges fixedwith 40mm SS screws 5 nos in each tile to frame workmade of local teak wood of size 20x15 mm in centre ofeach tile and bottom and top of work height, 40x15mmplaced at ends of each tile. The cladding shall be laidover backlayment of 1.00 mm thick expanded polyethylene foam of density 40kg/cum in two layers, firstlayer on wall surface before fixing wooden frame andsecond layer on frame under cladding. The bomboowood planks shall have minimum density of 1000Kg/cum & minimum Hardness 1000 Kgf. with Ecofriendly UV coating, etc. all complete as per direction ofEngineer-in-charge. |
| 120 | Providing and laying water proofing treatment on roofsof slabs by applying cement slurry mixed with waterproofing cement compound, as directed by Engineer-in-Charge and consisting of applying :(a) after surface preparation, first layer of slurry ofcement @ 0.488 kg/sqm mixed with water proofingcement compound @ 0.253 kg/sqm.(b) laying second layer of Fibre glass cloth when the firstlayer is still green. Overlaps of joints of fibre clothshould not be less than 10 cm.(c) third layer of 1.5 mm thickness consisting of slurry ofcement @ 1.289 kg/sqm mixed with water proofingcement compound @ 0.670 kg/sqm and fine sand @1.289 kg/sqm. This will be allowed to air cure for 4hours followed by water curing for 48 hours. The entiretreatment will be taken upto 30 cm on parapet wall andtucked into groove in parapet all around. |
| 121 | Grading roof for water proofing treatment complete as required as per direction of the Engineer-in-charge with :Cement concrete 1:2:4 (1 cement : 2 fine sand : 4 graded stone aggregate 20 mm nominal size) |
| 122 | Bill No. XI: Dismantling & Demolishing |
| 123 | Dismantling old plaster or pointing, raking out joints, cleaning and preparing the surface for re-plastering or re-pointing including disposal of rubbish to the dumping ground with all leads and lifts etc.complete as per direction of the Engineer- in-charge. |
| 124 | Dismantling doors, windows and clerestory windows (steel or wood) shutter including chowkhats, architrave, holdfasts etc. complete and stacking within 50 metres lead :Of area 3 sqm and below (Ground Floor Toilet) |
| 125 | Dismantling tile work in floors and roofs laid in cement mortar including stacking material within 50 metres lead.For Thickness of tiles 10 mm to 25 mm |
| 126 | Dismantling and stacking within 50 metres lead, fencing posts or struts including all earth work and dismantling of concrete etc. in base of:T or L iron pipe |
| 127 | Dismantling of flushing cistern of all types (C.I./PVC/Vitrious China) including stacking of useful materials near the site and disposal of unserviceable materials within 50 metres lead. |
| 128 | Dismantling W.C. Pan of all sizes including disposal of dismantled materials including malba all complete as per directions of Engineer-in-Charge. |
| 129 | Bill No. XII: Landscape |
| 130 | Earth work in surface excavation not exceeding 30 cm in depth but exceeding 1.5 m in width as well as 10 sqm on plan including disposal of excavated earth upto 50 m and lift upto 1.5 m, disposed soil to be levelled and neatly dressed: -All kinds of soil |
| 131 | Earth work in excavation by mechanical means (Hydraulic excavator) / manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan) including dressing of sides and ramming of bottoms, lift upto 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m.All kinds of soil |
| 132 | Excavation in soil by manual meansExcavation in Roadway cutting in soil by using manual means and carrying of cut earth to embankment site with all lifts and lead upto 50 metre as per MoR&TH Technical Specification clauses of section 300. |
| 133 | Excavation for structuresEarth work in excavation of foundation of structures as per drawing and technical specification, including setting out, construction of shoring and bracing, removal of stumps and other deleterious matter, dressing of sides and bottom, backfilling the excavation earth to the extent required and utilising the remaining earth locally for road work as per MoRT&H Technical Specification clauses of section 300.Ordinary soilBy manual means ( upto 3 m depth ) |
| 134 | Construction of Embankment with Material Obtained from Borrow PitsConstruction of embankment with approved material obtained from borrow pits with all lifts, transporting to site, spreading, grading to required slope and compacting to meet requirement of Tables 300.1 and 300.2 with a lead upto 1000 m as per MoRT&H Technical Specification clauses of section 300. |
| 135 | Construction of Subgrade and Earthen ShouldersConstruction of subgrade and earthen shoulders with approved material obtained from borrow pits with all lifts and leads, transporting to site , spreading, grading to required slope and compacted to meet requirement of Table 300.2 as per MoRT&H Technical Specification clauses of section 300. |
| 136 | Compacting Original GroundCompacting original ground supporting subgradeLoosening of the ground upto a level of 500 mm below the subgrade level, watered, graded and compacted in layers to meet requirement of Tables 300.2 for subgrade construction as per MoRT&H Technical Specification clauses of section 300. |
| 137 | Providing and laying in position cement concrete of specified grade excluding the cost of centring and shuttering -All Work upto Plinth Level1:4:8 ( 1 Cement: 4 fine sand : 8 graded stone aggregate 40 mm nominal size) |
| 138 | Plain/reinforced cement concrete in substructure complete including formwork as per drawings & MoRD technical specification Clauses 802, 804, 805, 806, 807, 900, 1202 & 1204. (including centering, shuttering, staging etc. but excluding reinforcement)P.C.C grade M 15 (1:2.5:5 Nominal mix) |
| 139 | R.C.C grade M-25 |
| 140 | Supplying, fitting & placing Thermo-Mechanically treated bar/ Cold twisted deformed steel bar in substructure complete as per drawings & MoRD technical specification Clauses 1002, 1005, 1010 and 1202. |
| 141 | Providing & laying reinforced cement concrete in superstructure as per drawings & MoRD technical specifications Clauses 800, 900, 1205.4 & 1205.5 (including centering, shuttering, staging etc. but excluding reinforcement).R.C.C M 25For height upto 5 m |
| 142 | For height from 5 m to 10 m |
| 143 | R.C.C. Grade M 30For height upto 5 m |
| 144 | Supplying, fitting, & placing Thermo-Mechanically treated bar/ Cold twisted deformed steel bar reinforcement in superstructure complete as per drawing & MoRD technical specifications Clauses 1002, 1010 & 1202. |
| 145 | Providing weep holes in brick masonry/ stone masonry, plain/ reinforced concrete abutment, wing wall, return wall with 100 mm dia AC pipe or uPVC pipe (110 mm OD of 6.0 kg/cm2 pressure) extending through the full width of the structures with slope of 1(V):20(H) towards drawing face complete as per drawing and MoRD technical specification clauses 614, 709, 1204.3.7. |
| 146 | Providing and laying Flooring complete as per drawing an Technical specifications laid over 100 mm thick cement concrete bedding as per drawing and MoRT&H Technical specifications clause 2505.Rubble stone laid in cement mortar 1:3, 300 mm thick |
| 147 | Granular sub-base with Well Graded Material (Table 400.1) using Jhama Brick AggregateBy Mix in Place MethodConstruction of granular Sub-base by providing well graded material (Jhama Brick aggregates) spreading in uniform layers with motor grader on prepared surface, mixing by mix in place metjod with rotovator at OMC, and compacting with smooth wheel rollr to achieve the desired densitty, complete as per MoRD Technical Specification Clause 401.For Grading-I Material |
| 148 | Excavating, supplying and filling of local earth (including royalty) by mechanical transport upto a lead of 5 km also including ramming and watering of the earth in layers not exceeding 20 cm in trenches, plinth, sides of foundation etc. complete. |
| 149 | Providing & laying filter media with jhama brick aggregates as per specification to a thickness of not less than 600 mm with smaller size towards the soil & bigger size towards the wall & providing over the entire surface behind abutment, wing wall, return wall to the full height, compacted to firm condition complete as per drawing and MoRD technical specification clause 2504.2.2. |
| 150 | Granular sub-base with Well Graded Material (Table 400.1) using Jhama Brick Aggregate(A) By Mix in Place MethodConstruction of granular Sub-base by providing well graded material (Jhama Brick aggregates) spreading in uniform layers with motor grader on prepared surface, mixing by mix in place metjod with rotovator at OMC, and compacting with smooth wheel rollr to achieve the desired densitty, complete as per MoRD Technical Specification Clause 401.(i) For Grading - I Material (jhama brick aggreate) |
| 151 | Water Bound Macadam Sub-Base / Base using Jhama Brick AggragateWBM Grading - 2Providing, laying, spreading and compacting jhama brick aggregates of specific sizes to water bound macadam specification including spreading in uniform thickness, hand packing rolling with three wheel roller 80-100 kN in stages to proper grade and camber, applying and brooming binding materials to fill up the interstices of coarse aggregate, watering and compacting to the required density Grading- 2 as per MoRD Technical Specification Clause 405.By Manual Means |
| 152 | Water Bound Macadam Sub-Base / BaseWBM Grading 1Providing, laying, spreading and compacting stone aggregates of specific sizes to water bound macadam specification including spreading in uniform thickness, hand packing, rolling with three wheel 80-100 kN static roller in stages to proper grade and camber, applying and brooming, stone screening/ binding materials to fill up the interstices of coarse aggregate, watering and compacting to the required density 'Grading 1' as per MoRD Technical Specification Clause 404.By Manual Means |
| 153 | Tack coat using hot straight run bitumen of grade VG-30 on W.B.M.Providing and applying tack coat using hot straight run bitumen of grade VG-30, including heating the bitumen, spraying the bitumen, cleaning and preparing the existing road surface as per specifications: On W.B.M. @ 0.75 kg/ sqm. |
| 154 | 25 mm thick Open-Graded Premix Carpet using Bituminous(Bitumen VG-30) Binder with organosilane nanotechnologyProviding, laying and rolling of open-graded premix carpet of 25 mm thickness composed of 13.2 mm to 5.6 mm aggregates using bitumen (Bitumen VG-30 mixed with 0.1% organosilane nanotechnology Zycotherm by weight of bituminous binder) to required line, grade and level to serve as wearing course on a previously prepared base, including mixing in a suitable plant, laying and rolling with a three wheel 80 - 100 kN static roller capacity, finished to required level and grades to be followed by seal coat of either Type A or Type B or Type C or Type D as per Technical Specification Clause 508By Manual Means |
| 155 | 18 mm thick granite flooring iin pathways, foothpaths, copings, exterior flooring etc. in 1:4 Cement Mortar |
| 156 | Stone tile (polished) work for wall lining over12mm thick bed of cement mortar 1:3 (1 cement :3 fine sand) and cement slurry @ 3.3 kg/sqmincluding pointing in white cement completeincluding rubbing, curing etc. complete at alllevels as required:-8 mm thickGranite of any colour and shade duly approved . |
| 157 | Providing and laying cement concrete in kerbs, steps and the like at or near ground level excluding the cost of centering, shuttering and finishing.1:1½:3 ( 1 Cement: 1½ fine sand : 3 graded stone aggregate 20 mm nominal size) |
| 158 | Providing and laying factory made kerb stoneProviding and laying at or near ground level factory made kerb stone of M-25 grade cement concrete inposition to the required line, level and curvature jointed with cement mortar 1:3 (1 cement : 3 sand), including making joints with or without grooves (thickness of joints except at sharp curve shall not to more than 5 mm), including making drainage opening wherever required complete etc. as per direction of Engineer-in-Charge (length of finished kerb edging shall be measured for payment). (Precast c.c. kerb stone shall be approved by Engineer-in- Charge). |
| 159 | 60 mm thick factory made c.c. interlocking paver block of M-35 GradeProviding and laying factory made coloured chamfered edge Cement Concrete paver blocks of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over 50 mm thick compacted bed of sand, compacting and proper embedding/laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with fine sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand in footpath, parks, lawns, drive ways or light traffic parking etc. complete as per specifications & approval/ direction of Engineer-in-Charge.60 mm thick c.c. paver block of M-35 grade with approved colour, design and pattern. |
| 160 | 80 mm thick factory made c.c interlocking paver block of M-35 GradeProviding and laying factory made chamfered edge Cement Concrete paver blocks of required strength, thickness & size/ shape, made by table vibratory method to attain superior smooth finish using PU or equivalent moulds, laid in required grey colour & pattern over 50 mm thick compacted bed of sand, compacting and proper embedding/ laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with fine sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand in footpath, parks, lawns, drive ways or light traffic parking etc. all complete as per specifications & approval / direction of the Engineer -in-Charge:80 mm thick c.c. paver block of M-35 grade with approved colour, design and pattern. Cement concrete 1:2:4 in pavements, laid to required slope and camber in panels |
| 161 | Providing and fixing stainless steel (Grade 304) railing made of Hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, including fixing the railing with necessary accessories & stainless steel dash fasteners , stainless steel bolts etc., of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-in-charge, (for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts, fasteners etc.). |
| 162 | Providing and fixing G.I. chain link fabric fencing of required width in mesh size 25x25 mm made of G.I. wire of dia 3 mm including strengthening with 2 mm dia wire or nuts, bolts and washers asrequired complete as per the direction of Engineer-in-charge. |
| 163 | Providing and fixing as per drawing /image STAINLESS STEEL DUSTBIN SERIES : ,600MM DIA X900MM HEIGHT with post hight-1200 and pipe dia 40mm SS-Grade-304 (2 NOS. FOrm. A ONE SET) with provision of opening at the bottom of the bin. |
| 164 | Providing and fixing stainless steel ( Grade 304) Sign board/Benches,chair,Scultures,canoppy made of Hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing tubes, channels, plates etc., including welding, grinding, and making curvature (wherever required) and fitting the same withbuffing, polishing necessary stainless steel nuts and bolts complete, i/c fixing the railing with necessary accessories & stainless steel dash fasteners , stainless steel bolts etc., of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-in- shall be considered excluding fixing accessories such as nuts, bolts,fasteners etc.-Making the Sign board on S steel sheet |
| 165 | Bill No. XIII: Horticulture |
| 166 | Fine dressing the ground |
| 167 | Mixing earth and sludge or farm. yard manure in proportion specified or as directed. |
| 168 | Spreading of sludge, farm.-yard manure or/and good earth in required thickness (Cost of sludge, farm.yard manure or /and good earth to be paid for separately) (MIN 200 MM LAYER). |
| 169 | Providing and laying Neelgiri/Mexican grass turf with earth 50mm to 60mm Thickness of existing ground prepared with proper level and ramming with tools wooden (Dhurmos) and then rolling the surface with light roller make the surface smoothen and light waterning with sprinkler and maintenance for 30 days or more till the grass establish properly, as per direction of Officer-in-charge |
| 170 | Providing & laying Selection no. 1 grass turf with earth 50mm to 60mm thickness on existing ground prepared with proper level and ramming with required tools wooden and than rolling the surface with light roller make the surface smoothen and light watering the same, as per direction of Officer-in-charge. |
| 171 | Mixing earth and sludge or faRmt. yard manure in proportion specified or as directed. |
| 172 | Digging holes in all kinds of soil, and refilling the same, with the excavated earth, mixed with well decayed farm-yard manure (cost of well decayed farm yard manure to be paid separately) in the ratio of 2:1 by volume (2 parts of stacked volume of earth after reduction by 20% : 1part of stacked volume of manure after reduction by 8%) flooding with water, dressing including removal of rubbish and surplus earth, if any with all leads and liftsHoles 1.2 m dia and 1.2 m deep. |
| 173 | Digging holes in all kinds of soil, and refilling the same, with the excavated earth, mixed with well decayed farm-yard manure (cost of well decayed farm yard manure to be paid separately) in the ratio of 2:1 by volume (2 parts of stacked volume of earth after reduction by 20% : 1part of stacked volume of manure after reduction by 8%) flooding with water, dressing including removal of rubbish and surplus earth, if any with all leads and liftsHoles 60 cm dia, and 60 cm deep. |
| 174 | Supply & Install Trees/ Palms inclusive of: i).Removal of rubbish/ all construction debris /site trash, and surplus earth inclusive with all leads and lift. ii). Treat the pit with Chloropyriphos solution of 0.5% concentration(5 ml/liter water) as required iv). Flooding the pit with water after making kiaries where required vi). Fertilise the pit by adding DAP 50gm, MOP 25 gm, 50gm neem oil cake and 50 gm stearameal per pit at the time of planting-FICUS BENJAMINA,IN RECTANGULAR BOX HEDGES 1.2X 1.2M X 1.2M Minimum 3.6 / 4.0 m overall height,Minimum 100mm caliper,Multibranching at 2.4m from collar |
| 175 | Supply & Install Trees/ Palms inclusive of: i).Removal of rubbish/ all construction debris /site trash, and surplus earth inclusive with all leads and lift. ii). Treat the pit with Chloropyriphos solution of 0.5% concentration(5 ml/liter water) as required iv). Flooding the pit with water after making kiaries where required vi). Fertilise the pit by adding DAP 50gm, MOP 25 gm, 50gm neem oil cake and 50 gm stearameal per pit at the time of planting-ERYTHRINA INDICA,Minimum 3.0/3.5m overall height,Multibranching at 2.5m from collar, min. 60m Caliper. |
| 176 | Supply & Install Trees/ Palms inclusive of: i).Removal of rubbish/ all construction debris /site trash, and surplus earth inclusive with all leads and lift. ii). Treat the pit with Chloropyriphos solution of 0.5% concentration(5 ml/liter water) as required iv). Flooding the pit with water after making kiaries where required vi). Fertilise the pit by adding DAP 50gm, MOP 25 gm, 50gm neem oil cake and 50 gm stearameal per pit at the time of planting-LAGERSTROEMIA SPECIOSA,Minimum 3.0/3.5m overall height,Multibranching at 2.5m from collar, min. 60m Caliper. |
| 177 | Supply & Install Trees/ Palms inclusive of: i).Removal of rubbish/ all construction debris /site trash, and surplus earth inclusive with all leads and lift. ii). Treat the pit with Chloropyriphos solution of 0.5% concentration(5 ml/liter water) as required iii). Flooding the pit with water after making kiaries where required iv). Fertilise the pit by adding DAP 50gm, MOP 25 gm, 50gm neem oil cake and 50 gm stearameal per pit at the time of planting CYCUS REVOLUTA,FERN SAGO,Minimum 0.6 M trunk height, Minimum 3 whorls with 15 leaves each. |
| 178 | Supply & Install Shrubs inclusive of: i).Removal of rubbish/ all construction debris /site trash, and surplus earth inclusive with all leads and lift. ii). Treat the pit with Chloropyriphos solution of 0.5% oncentration(5 ml/liter water) as required iv). Flooding the pit with water after making kiaries where required vi). Fertilise the pit by adding DAP 50gm, MOP 25 gm, 50gm neem oil cake and 50 gm stearameal per pit at the time of planting.-NYCTANTHES ARBOR-TRISTIS,Minimum 600mm height@900mmc/c,Bushy, Multibranching, Flowering. |
| 179 | Supply & Install Shrubs inclusive of: i).Removal of rubbish/ all construction debris /site trash, and surplus earth inclusive with all leads and lift. ii). Treat the pit with Chloropyriphos solution of 0.5% oncentration(5 ml/liter water) as required iv). Flooding the pit with water after making kiaries where required vi). Fertilise the pit by adding DAP 50gm, MOP 25 gm, 50gm neem oil cake and 50 gm stearameal per pit at the time of planting-CALLIANDRA EMARGINATA,Minimum 900mm height@900mmc/c,Bushy, Multibranching, Flowering |
| 180 | Supply & Install Shrubs inclusive of: i).Removal of rubbish/ all construction debris /site trash, and surplus earth inclusive with all leads and lift. ii). Treat the pit with Chloropyriphos solution of 0.5% oncentration(5 ml/liter water) as required iv). Flooding the pit with water after making kiaries where required vi). Fertilise the pit by adding DAP 50gm, MOP 25 gm, 50gm neem oil cake and 50 gm stearameal per pit at the time of planting-Nerium oleander 'Petite Pink' Dwarf Pink , Minimum 900mm height@750mmc/c,Bushy, Multibranching, Flowering |
| 181 | Supply & Install Shrubs inclusive of: i).Removal of rubbish/ all construction debris /site trash, and surplus earth inclusive with all leads and lift. ii). Treat the pit with Chloropyriphos solution of 0.5% oncentration(5 ml/liter water) as required iv). Flooding the pit with water after making kiaries where required vi). Fertilise the pit by adding DAP 50gm, MOP 25 gm, 50gm neem oil cake and 50 gm stearameal per pit at the time of planting.-Hibiscus Rosasinium Cooperii Minimum 600mm height @600mmc/c,Bushy |
| 182 | Supply & Install Shrubs inclusive of: i).Removal of rubbish/ all construction debris /site trash, and surplus earth inclusive with all leads and lift. ii). Treat the pit with Chloropyriphos solution of 0.5% oncentration(5 ml/liter water) as required iv). Flooding the pit with water after making kiaries where required vi). Fertilise the pit by adding DAP 50gm, MOP 25 gm, 50gm neem oil cake and 50 gm stearameal per pit at the time of planting.-MARIGOLD Minimum 600mm height @600mmc/c,Bushy |
| 183 | Supply & Install Shrubs inclusive of: i).Removal of rubbish/ all construction debris /site trash, and surplus earth inclusive with all leads and lift. ii). Treat the pit with Chloropyriphos solution of 0.5% oncentration(5 ml/liter water) as required iv). Flooding the pit with water after making kiaries where required vi). Fertilise the pit by adding DAP 50gm, MOP 25 gm, 50gm neem oil cake and 50 gm stearameal per pit at the time of planting.-CESTRIUM ELEGANS Minimum 600mm height @600mmc/c,Bushy |
| 184 | Supply & Install Shrubs inclusive of: i).Removal of rubbish/ all construction debris /site trash, and surplus earth inclusive with all leads and lift. ii). Treat the pit with Chloropyriphos solution of 0.5% oncentration(5 ml/liter water) as required iv). Flooding the pit with water after making kiaries where required vi). Fertilise the pit by adding DAP 50gm, MOP 25 gm, 50gm neem oil cake and 50 gm stearameal per pit at the time of planting.-BELOPERONE GUTTATA Minimum 600mm height @600mmc/c,Bushy |
| 185 | Supply & Install Shrubs inclusive of: i).Removal of rubbish/ all construction debris /site trash, and surplus earth inclusive with all leads and lift. ii). Treat the pit with Chloropyriphos solution of 0.5% oncentration(5 ml/liter water) as required iv). Flooding the pit with water after making kiaries where required vi). Fertilise the pit by adding DAP 50gm, MOP 25 gm, 50gm neem oil cake and 50 gm stearameal per pit at the time of planting.-BAUHINIA TOMENTOSA Minimum 600mm height @600mmc/c,Bushy |
| 186 | Supply & Install Shrubs inclusive of: i).Removal of rubbish/ all construction debris /site trash, and surplus earth inclusive with all leads and lift. ii). Treat the pit with Chloropyriphos solution of 0.5% oncentration(5 ml/liter water) as required iv). Flooding the pit with water after making kiaries where required vi). Fertilise the pit by adding DAP 50gm, MOP 25 gm, 50gm neem oil cake and 50 gm stearameal per pit at the time of planting.-ACOKANTHERA SCHIMPERI Minimum 600mm height @600mmc/c,Bushy |
| 187 | Mixing earth and sludge or faRmt. yard manure in proportion specified or as directed. |
| 188 | Supply &Install ground covers/ Shade plants inclusive of: i).Removal of rubbish/ all construction debris /site trash, and surplus earth inclusive with all leads and lift. ii). Treat the pit with Chloropyriphos solution of 0.5% oncentration(5 ml/liter water) as required iv). Flooding the pit with water after making kiaries where required vi). Fertilise the pit by adding DAP 50gm, MOP 25 gm, 50gm neem oil cake and 50 gm stearameal per pit at the time of planting.-Hibiscus Rosasinium Cooperii Minimum 600mm height @600mmc/c,Bushy |
| 189 | Supply &Install ground covers/ Shade plants inclusive of: i).Removal of rubbish/ all construction debris /site trash, and surplus earth inclusive with all leads and lift. ii). Treat the pit with Chloropyriphos solution of 0.5% oncentration(5 ml/liter water) as required iv). Flooding the pit with water after making kiaries where required vi). Fertilise the pit by adding DAP 50gm, MOP 25 gm, 50gm neem oil cake and 50 gm stearameal per pit at the time of planting.g-HAMELIA PATTENS,Minimum 1500mm height@900mmc/c,Bushy, Multibranching |
| 190 | Supply &Install ground covers/ Shade plants inclusive of: i).Removal of rubbish/ all construction debris /site trash, and surplus earth inclusive with all leads and lift. ii). Treat the pit with Chloropyriphos solution of 0.5% oncentration(5 ml/liter water) as required iv). Flooding the pit with water after making kiaries where required vi). Fertilise the pit by adding DAP 50gm, MOP 25 gm, 50gm neem oil cake and 50 gm stearameal per pit at the time of planting.-JASMINUM HUMILE,Minimum 900mm height@600mmc/c,Bushy, Multibranching, Flowering |
| 191 | Supply &Install ground covers/ Shade plants inclusive of: i).Removal of rubbish/ all construction debris /site trash, and surplus earth inclusive with all leads and lift. ii). Treat the pit with Chloropyriphos solution of 0.5% oncentration(5 ml/liter water) as required iv). Flooding the pit with water after making kiaries where required vi). Fertilise the pit by adding DAP 50gm, MOP 25 gm, 50gm neem oil cake and 50 gm stearameal per pit at the time of planting.-TABERNAEMONTANA CORONERIA,Minimum 600mm height@600mmc/c,Bushy, Multibranching, Flowering |
| 192 | Supply &Install ground covers/ Shade plants inclusive of: i).Removal of rubbish/ all construction debris /site trash, and surplus earth inclusive with all leads and lift. ii). Treat the pit with Chloropyriphos solution of 0.5% oncentration(5 ml/liter water) as required iv). Flooding the pit with water after making kiaries where required vi). Fertilise the pit by adding DAP 50gm, MOP 25 gm, 50gm neem oil cake and 50 gm stearameal per pit at the time of planting.-TABERNAEMONTANA CORONERIA VARIEGATED,Minimum 600mm height@600mmc/c,Bushy, Multibranching, Flowering |
| 193 | Supply &Install ground covers/ Shade plants inclusive of: i).Removal of rubbish/ all construction debris /site trash, and surplus earth inclusive with all leads and lift. ii). Treat the pit with Chloropyriphos solution of 0.5% oncentration(5 ml/liter water) as required iv). Flooding the pit with water after making kiaries where required vi). Fertilise the pit by adding DAP 50gm, MOP 25 gm, 50gm neem oil cake and 50 gm stearameal per pit at the time of planting.g-IXORA sinensis,Minimum 250mm height@250mmc/c,Bushy, Multibranching, Flowering |
| 194 | Supply &Install ground covers/ Shade plants inclusive of: i).Removal of rubbish/ all construction debris /site trash, and surplus earth inclusive with all leads and lift. ii). Treat the pit with Chloropyriphos solution of 0.5% oncentration(5 ml/liter water) as required iv). Flooding the pit with water after making kiaries where required vi). Fertilise the pit by adding DAP 50gm, MOP 25 gm, 50gm neem oil cake and 50 gm stearameal per pit at the time of planting.g-IXORA CHENINSIS,Minimum 250mm height@250mmc/c,Bushy, Multibranching, Flowering |
| 195 | Supply &Install ground covers/ Shade plants inclusive of: i).Removal of rubbish/ all construction debris /site trash, and surplus earth inclusive with all leads and lift. ii). Treat the pit with Chloropyriphos solution of 0.5% oncentration(5 ml/liter water) as required iv). Flooding the pit with water after making kiaries where required vi). Fertilise the pit by adding DAP 50gm, MOP 25 gm, 50gm neem oil cake and 50 gm stearameal per pit at the time of planting.g-OCIMUM SANCTUM - BASIL ( BLACK TULSI ),Minimum 200mm height@200mmc/c,Bushy, Multibranching, Flowering |
| 196 | Supply &Install ground covers/ Shade plants inclusive of: i).Removal of rubbish/ all construction debris /site trash, and surplus earth inclusive with all leads and lift. ii). Treat the pit with Chloropyriphos solution of 0.5% oncentration(5 ml/liter water) as required iv). Flooding the pit with water after making kiaries where required vi). Fertilise the pit by adding DAP 50gm, MOP 25 gm, 50gm neem oil cake and 50 gm stearameal per pit at the time of planting.g-OCIMUM SANCTUM - BASIL ( GREEN TULSI ),Minimum 200mm height@200mmc/c,Bushy, Multibranching, Flowering |
| 197 | Supply &Install ground covers/ Shade plants inclusive of: i).Removal of rubbish/ all construction debris /site trash, and surplus earth inclusive with all leads and lift. ii). Treat the pit with Chloropyriphos solution of 0.5% oncentration(5 ml/liter water) as required iv). Flooding the pit with water after making kiaries where required vi). Fertilise the pit by adding DAP 50gm, MOP 25 gm, 50gm neem oil cake and 50 gm stearameal per pit at the time of planting.g-CASSIA BIFLORA,Minimum 900mm height@900mmc/c,Bushy, Multibranching, Flowering |
| 198 | Supply &Install ground covers/ Shade plants inclusive of: i).Removal of rubbish/ all construction debris /site trash, and surplus earth inclusive with all leads and lift. ii). Treat the pit with Chloropyriphos solution of 0.5% oncentration(5 ml/liter water) as required iv). Flooding the pit with water after making kiaries where required vi). Fertilise the pit by adding DAP 50gm, MOP 25 gm, 50gm neem oil cake and 50 gm stearameal per pit at the time of planting.g-IXORA RED,Minimum 250mm height@250mmc/c,Bushy, Multibranching, Flowering |
| 199 | Supply &Install ground covers/ Shade plants inclusive of: i).Removal of rubbish/ all construction debris /site trash, and surplus earth inclusive with all leads and lift. ii). Treat the pit with Chloropyriphos solution of 0.5% oncentration(5 ml/liter water) as required iv). Flooding the pit with water after making kiaries where required vi). Fertilise the pit by adding DAP 50gm, MOP 25 gm, 50gm neem oil cake and 50 gm stearameal per pit at the time of planting.-LAGERSTROEMIA INDICA ROSEA Minimum 1500mm height @1500mmc/c,Bushy |
| 200 | Supply &Install ground covers/ Shade plants inclusive of: i).Removal of rubbish/ all construction debris /site trash, and surplus earth inclusive with all leads and lift. ii). Treat the pit with Chloropyriphos solution of 0.5% oncentration(5 ml/liter water) as required iv). Flooding the pit with water after making kiaries where required vi). Fertilise the pit by adding DAP 50gm, MOP 25 gm, 50gm neem oil cake and 50 gm stearameal per pit at the time of planting.-HELLICONIA METTALICA,Minimum 150mm height @200mmc/c,bushy |
| 201 | Supply &Install ground covers/ Shade plants inclusive of: i).Removal of rubbish/ all construction debris /site trash, and surplus earth inclusive with all leads and lift. ii). Treat the pit with Chloropyriphos solution of 0.5% oncentration(5 ml/liter water) as required iv). Flooding the pit with water after making kiaries where required vi). Fertilise the pit by adding DAP 50gm, MOP 25 gm, 50gm neem oil cake and 50 gm stearameal per pit at the time of planting.-HEMILIA PATENS,Minimum 150mm height @200mmc/c,bushy |
| 202 | Supply &Install ground covers/ Shade plants inclusive of: i).Removal of rubbish/ all construction debris /site trash, and surplus earth inclusive with all leads and lift. ii). Treat the pit with Chloropyriphos solution of 0.5% oncentration(5 ml/liter water) as required iv). Flooding the pit with water after making kiaries where required vi). Fertilise the pit by adding DAP 50gm, MOP 25 gm, 50gm neem oil cake and 50 gm stearameal per pit at the time of planting.-MUSSAENDA ERYTHROPHYLLA,Minimum 150mm height @200mmc/c,bushy |
| 203 | Supply &Install ground covers/ Shade plants inclusive of: i).Removal of rubbish/ all construction debris /site trash, and surplus earth inclusive with all leads and lift. ii). Treat the pit with Chloropyriphos solution of 0.5% oncentration(5 ml/liter water) as required iv). Flooding the pit with water after making kiaries where required vi). Fertilise the pit by adding DAP 50gm, MOP 25 gm, 50gm neem oil cake and 50 gm stearameal per pit at the time of planting.-Hibiscus Rosa Sinensis Minimum 600mm height @600mmc/c,Bushy |
| 204 | Supply &Install ground covers/ Shade plants inclusive of: i).Removal of rubbish/ all construction debris /site trash, and surplus earth inclusive with all leads and lift. ii). Treat the pit with Chloropyriphos solution of 0.5% oncentration(5 ml/liter water) as required iv). Flooding the pit with water after making kiaries where required vi). Fertilise the pit by adding DAP 50gm, MOP 25 gm, 50gm neem oil cake and 50 gm stearameal per pit at the time of planting.-CUPHEA HYSSOPIFOLIA PURPLE Minimum 200mm height @200mmc/c,Bushy |
| 205 | Supply &Install ground covers/ Shade plants inclusive of: i).Removal of rubbish/ all construction debris /site trash, and surplus earth inclusive with all leads and lift. ii). Treat the pit with Chloropyriphos solution of 0.5% oncentration(5 ml/liter water) as required iv). Flooding the pit with water after making kiaries where required vi). Fertilise the pit by adding DAP 50gm, MOP 25 gm, 50gm neem oil cake and 50 gm stearameal per pit at the time of planting.-TECOMARIA CAPENSIS Minimum 600mm height @600mmc/c,Bushy |
| 206 | Supply &Install ground covers/ Shade plants inclusive of: i).Removal of rubbish/ all construction debris /site trash, and surplus earth inclusive with all leads and lift. ii). Treat the pit with Chloropyriphos solution of 0.5% oncentration(5 ml/liter water) as required iv). Flooding the pit with water after making kiaries where required vi). Fertilise the pit by adding DAP 50gm, MOP 25 gm, 50gm neem oil cake and 50 gm stearameal per pit at the time of planting.-OPHIOPOGON BLACK GRASS. |
| 207 | Supply &Install ground covers/ Shade plants inclusive of: i).Removal of rubbish/ all construction debris /site trash, and surplus earth inclusive with all leads and lift. ii). Treat the pit with Chloropyriphos solution of 0.5% oncentration(5 ml/liter water) as required iv). Flooding the pit with water after making kiaries where required vi). Fertilise the pit by adding DAP 50gm, MOP 25 gm, 50gm neem oil cake and 50 gm stearameal per pit at the time of planting.-LAVENDER |
| 208 | Supply &Install ground covers/ Shade plants inclusive of: i).Removal of rubbish/ all construction debris /site trash, and surplus earth inclusive with all leads and lift. ii). Treat the pit with Chloropyriphos solution of 0.5% oncentration(5 ml/liter water) as required iv). Flooding the pit with water after making kiaries where required vi). Fertilise the pit by adding DAP 50gm, MOP 25 gm, 50gm neem oil cake and 50 gm stearameal per pit at the time of planting.-ALTERNANTHERA RED |
| 209 | Supply &Install ground covers/ Shade plants inclusive of: i).Removal of rubbish/ all construction debris /site trash, and surplus earth inclusive with all leads and lift. ii). Treat the pit with Chloropyriphos solution of 0.5% oncentration(5 ml/liter water) as required iv). Flooding the pit with water after making kiaries where required vi). Fertilise the pit by adding DAP 50gm, MOP 25 gm, 50gm neem oil cake and 50 gm stearameal per pit at the time of planting.-WEDELIA TRILOBATA,Minimum 3 runners per plant,Minimum 150mm height @200mmc/c. |
| 210 | Supply &Install ground covers/ Shade plants inclusive of: i).Removal of rubbish/ all construction debris /site trash, and surplus earth inclusive with all leads and lift. ii). Treat the pit with Chloropyriphos solution of 0.5% oncentration(5 ml/liter water) as required iv). Flooding the pit with water after making kiaries where required vi). Fertilise the pit by adding DAP 50gm, MOP 25 gm, 50gm neem oil cake and 50 gm stearameal per pit at the time of planting.-CHLOROPHYTUM COSMOSOM VITTATUM, Minimum 200mm height @200mmc/c, Minimum 3 runners per plant |
| 211 | Supply & Install plants to form hedge , inclusive of: i).Removal of rubbish/ all construction debris /site trash, and surplus earth inclusive with all leads and lift. ii). Treat the pit with Chloropyriphos solution of 0.5% oncentration(5 ml/liter water) as required iv). Flooding the pit with water after making kiaries where required vi). Fertilise the pit by adding DAP 50gm, MOP 25 gm, 50gm neem oil cake and 50 gm stearameal per pit at the time of planting.-MURRAYA EXOTICA,Minimum 300mm height @300mmc/c,Bushy |
| 212 | Supply & Install plants to form hedge, inclusive of: i).Removal of rubbish/ all construction debris /site trash, and surplus earth inclusive with all leads and lift. ii). Treat the pit with Chloropyriphos solution of 0.5% oncentration(5 ml/liter water) as required iv). Flooding the pit with water after making kiaries where required vi). Fertilise the pit by adding DAP 50gm, MOP 25 gm, 50gm neem oil cake and 50 gm stearameal per pit at the time of planting.-FICUS PANDA Minimum 300 mm height @200mmc/c,Bushy |
| 213 | Supplying at site of work well-decayed farm.-yard manure, from any available source, approved by the Engineer-in-charge including screening and stacking. |
| 214 | Supplying site of work-Deoiled Neem-Cake duly packed in used bags |
| 215 | Supplying at site of work sludge duly stacked at site. |
| 216 | Bill No. XIV: Sanitation Installations & Plumbing |
| 217 | Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge. Concealed work including cutting chases and making good the walls etc.15 mm nominal outer dia .Pipes. |
| 218 | 20 mm nominal outer dia .Pipes. |
| 219 | 32 mm nominal outer dia .Pipes. |
| 220 | Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings This includes jointing of pipes & fittings with one step CPVC solvent cement ,trenching ,refilling & testing of joints complete as per direction of Engineer in Charge. - External work32 mm nominal outer dia .Pipes. |
| 221 | 50 mm nominal outer dia .Pipes. |
| 222 | 75 mm nominal inner dia .Pipes. |
| 223 | 100 mm nominal inner dia .Pipes. |
| 224 | Providing and fixing on wall face unplasticised Rigid PVC rain water pipes (working pressure 4 kg/cm2) conforming to IS : 13592 Type A including jointing with seal ring conforming to IS : 5382 leaving 10 mm gap for thermal expansion etc. complete as per direction of Engineer-in-charge : Single socketed pipe - 75 mm OD |
| 225 | Single socketed pipe - 110 mm OD |
| 226 | Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water, soil, waste & vent pipes pipes conforming to IS : 13592 Type A including jointing with seal ring conforming to IS : 5382 leaving 10 mm gap for thermal expansion: Coupler75 mm |
| 227 | 110 mm |
| 228 | Single equal tee with door - 75x75x75 mm |
| 229 | 110x110x110 mm |
| 230 | Bend 87.5° - 75 mm |
| 231 | 110 mm |
| 232 | Single unequal junction of required degree with door110x110x75 mm |
| 233 | Providing and fixing unplasticised -PVC pipe clips of approved design to unplasticised - PVC rain water, soil, waste & vent pipes by means of 50x50x50mm hard wood plugs, screwed with M.S. screws of required length including cutting brick work and fixing with cement mortar 1 : 4 (1cement : 4 fine sand) making good the wall etc. complete. 75 mm |
| 234 | 110 mm |
| 235 | Providing and fixing water closet squatting pan (Indian type W.C. pan ) with 100mm sand cast Iron P or S trap, 10 litre low level white P.V.C. flushing cistern with manually controlled device (handle lever) conforming to IS : 7231, with all fittings and fixtures complete including cutting and making good the walls and floors wherever required :White Vitreous china Orrisa pattern W.C. pan of size 580x440 mm with integral type foot rests. |
| 236 | Providing and fixing white vitreous china pedestal type water closet (European type) with seat and lid, 10 litre low level white vitreous china flushing cistern & C.P. flush bend with fittings & C.I. brackets, 40mm flush bend, overflow arrangement with specials of standard make and mosquito proof coupling of approved municipal design complete including painting of fittings and brackets, cutting and making good the walls and floors wherever required :W.C. pan with ISI marked white solid plastic seat and lid. |
| 237 | Providing and Fixing one piece construction white vitreous china squatting plate with an integral longitudinal flushing pipe, white P.V.C. Automatic flushing cistern, with fittings, standard size G.I. flush pipe for back and front flush with standard spreader pipes with fittings, G.I clamps and C.P. brass coupling complete including painting of fittings and cutting and making good the walls and floors etc. wherever required :Single squatting plate with 5 litre P.V.C. automatic flushing cistern. |
| 238 | Range of two squatting plates with 5 litre P.V.C. automatic flushing cistern. |
| 239 | Providing and fixing floor mounted, white vitreous china single piece, double traps syphonic water closet of approved brand/make, shape, size and pattern including integrated white vitreous china cistern of capacity 10 litres with dual flushing system, including all fittings and fixtures with seat cover, cistern fittings, nuts, bolts and gasket etc including making connection with the existing P/S trap, complete in all respect as per directions of Engineerin- Charge. |
| 240 | Providing and Fixing white vitreous china flat back half stall urinal of size 580x380x350mm with white PVC automatic flushing cistern, with fittings, standard size C.P. brass flush pipe, spreaders with unions and clamps (all in C.P. brass) with waste fitting as per IS : 2556, C.I. trap with outlet grating and other couplings in C.P. brass including painting of fittings and cutting and making good the walls and floors wherever required :Single half stall urinal with 5 litre P.V.C. automatic flushing cistern. |
| 241 | Range of two half stall urinals with 5 litre P.V.C. automatic flushing cistern. |
| 242 | Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps,32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require :White Vitreous China Wash basin size 630x450 mm with a pair of 15 mm C.P. brass pillar taps |
| 243 | White Vitreous China Wash basin size 550x400 mm with a pair of 15 mm C.P. brass pillar taps. |
| 244 | Providing and fixing white vitreous china pedestal for wash basin completely recessed at the back for the reception of pipes and fittings. |
| 245 | Providing and fixing Stainless Steel AISI 304 (18/8) kitchen sink as per IS 13983 with C.I. brackets and stainless steel plug 40 mm including painting of fittings and brackets, cutting and making good the walls wherever required:Kitchen sink with drain board510x1040 mm bowl depth 250mm. |
| 246 | Providing and fixing controlled flush, low level cistern made of vitreous china with all fittings complete.10 litre (full flush) capacity-white |
| 247 | Providing and fixing G.I. inlet connection for flush pipe connecting with W.C. pan. |
| 248 | Providing and fixing P.V.C. waste pipe for sink or wash basin including P.V.C. waste fittings complete.Flexible pipe32 mm dia |
| 249 | 40 mm dia |
| 250 | Providing and fixing 100 mm sand cast Iron grating for gully trap. |
| 251 | Providing and fixing mirror of superior glass (of approved quality) and of required shape and size with plastic moulded frame of approved make and shade with 6 mm thick hard board backing :Circular shape 450 mm dia |
| 252 | Rectangular shape 453x357mm |
| 253 | Rectangular shape 1500x450 mm |
| 254 | Providing and fixing 600x120x5mm glass shelf with edges round of supported on anodised aluminium angle frame with C.P. brass brackets and guard rail complete fixed with 40 mm long screws, rawl plugs etc., complete. |
| 255 | Providing and fixing toilet paper holder :C.P. brass |
| 256 | Vitreous china |
| 257 | Providing and fixing PTMT Bottle Trap for Wash basin and sink.Bottle trap 38mm single piece moulded with height of 270mm, effective length of tail pipe 260mm from the centre of the waste coupling 77mm breadth with 25mm minimum water seal, weighing not less than 263gms. |
| 258 | Providing and fixing PTMT liquid soap container 109mm wide, 125mm high and 112mm distance from wall of standard shape with bracket of the same materials with snap fittings of approved quality and colours weighing not less than 105 gms. |
| 259 | Providing and fixing PTMT towel rail complete withbrackets fixed to wooden cleats with CP brass screwswith concealed fitting arrangement of approved qualityand colour.600mm long towel rail with total length of 645mm, width78mm and effective height of 88mm, weighing not lessthan 190gms. |
| 260 | Providing and fixing brass bib cock of approved quality :15 mm nominal bore |
| 261 | 20 mm nominal bore |
| 262 | Providing and fixing brass stop cock of approved quality :15 mm nominal bore |
| 263 | 20 mm nominal bore |
| 264 | Providing and fixing C.P. brass long body bib cock of approved quality conforming to IS standards and weighing not less than 690 gms. 15 mm nominal bore |
| 265 | Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end): 25 mm nominal bore |
| 266 | 32 mm nominal bore |
| 267 | Providing and fixing ball valve (brass) of approved quality High or low pressure, with plastic floats complete :20 mm nominal bore |
| 268 | 25 mm nominal bore |
| 269 | Providing and fixing C.P. brass shower rose with 15 or 20 mm inlet:100 mm diameter |
| 270 | 150 mm diameter |
| 271 | Providing and fixing C.P. brass angle valve for basin mixer and geyser points of approved quality conforming to IS:8931 15 mm nominal bore |
| 272 | Providing and placing on terrace (at all floor levels) polyethylene water storage tank ISI : 12701 marked with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank. |
| 273 | EXTERNAL PLUMBINGREINFORCED CEMENT CONCRETE WORKFilling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift upto 1.5 m. - All Work upto Plinth Level1:1:2 ( 1 Cement: 1 fine sand : 2 graded stone aggregate 20 mm nominal size) |
| 274 | Reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto plinth level. Thermo-Mechanically Treated bars of grade Fe-500D or more |
| 275 | WATER SUPPLYProviding and laying Double Flanged (Screwed/ Welded) Centrifugally (Spun) Ductile Iron Pipes of Class K 9 conforming to IS : 8329 :150 mm dia Ductile Iron Double Flanged |
| 276 | Providing and laying S&S Centrifugally Cast (Spun) / Ductile Iron Pipes conforming to IS : 8329150 mm dia Ductile Iron Class K-7 pipes |
| 277 | Providing and fixing C.I. sluice valves (with cap) complete with bolts, nuts, rubber insertions etc. (the tail pieces if required will be paid separately)100 mm diameter Class II |
| 278 | Providing and fixing C.I. double acting air valve of approved quality with bolts, nuts, rubber insertions etc. complete (The tail pieces, tapers etc if required will be paid separately): 50 mm dia |
| 279 | 80 mm dia |
| 280 | 100 mm dia |
| 281 | Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings This includes jointing of pipes & fittings with one step CPVC solvent cement ,trenching, refilling & testing of joints complete as per direction of Engineer in Charge.50 mm nominal outer dia .Pipes. |
| 282 | 62.50 mm nominal inner dia .Pipes. |
| 283 | 75 mm nominal inner dia .Pipes. |
| 284 | 100 mm nominal inner dia .Pipes. |
| 285 | Constructing masonry Chamber 60x60x75 cm, insidein brick work in cement mortar 1:4 (1 cement : 4 finesand) for sluice valve, with C.I. surface box 100mm.top diameter, 160 mm bottom diameter and 190mm deep ( inside) with chained lid and RCC topslab 1:2:4 mix (1 cement :2 coarse sand : 4 graded stone aggregate 20mm nominal size ) necessary excavation foundation concrete 1:5:10 (1 cement : 5fine sand : 10 graded stone aggregate 40 mm nominal size) and inside plastering with cement mortar 1:3 (1cement : 3 coarse sand) 12 mm thick finished with afloating coat of neat cement complete as perstandard design : With Second Class bricks |
| 286 | Providing, installation and commissioning of package type Iron Removal Plant comprising of Iron Removal Filter of dual media filter with anthracite coal, filter gravel, polypropelene double hexagonal nut strainer etc., mixing chamber for coagulants like sodium alluminates etc., oxidation chamber with manganese dioxide , metering pump for coagulant dosing, air compressor of suitable capacity with motor, back washing arrangements, disinfection with sodium hypochlorite solution through metering pump, all necessary pipes for raw water collection, inter connecting all the chambers, delivery outlet of 150 mm dia alongwith all related civil, mechanical and Electrical works etc. complete as per approved drawing, process flow, technical specification and direction of the Engineer - in - charge. 2500 G.P.H CAPACITY |
| 287 | Charges for drilling and boring of pilot hole in any soil strata bywater jet or any suitable method including collection ofsamples at various suitable levels and preservation ofsamples in polythene bags / sample boxes and disposal ofexcess soil or mud and maintain the pilot hole properly andrequired staging as per specification ( IS : 2800 ) and directionof the Engineer-in-charge.100 mm dia |
| 288 | Reaming of pilot hole to an enlarged bore hole in any soilstrata by manual means, disposal of excess soil or mud,including the cost for water etc. as required to maintain thebore hole properly as per specification and direction of theEngineer - in - charge.from 100 mm dia pilot hole to 250 mm bore hole |
| 289 | Providing & lowering of UPVC pipe as per IS:12818 after washing of the bore hole by manual means as per specification and direction of the Engineer - in - charge. 'CM' Casing pipe150 mm dia |
| 290 | 125 mm dia |
| 291 | RS' pipe100 mm dia |
| 292 | Washing & development of Tube Well by using hand pump or by any suitable method & testing of the well as per specification & direction of the Engineer in charge |
| 293 | Providing and fixing of UPVC end cap suitable for UPVC ‘CM’ casing or ‘CS’ casing or ‘RS’ pipes as per specification and direction of the Engineer-in-charge.100 mm dia |
| 294 | Providing and fixing of UPVC reducer suitable for UPVC ‘CM’ casing or ‘CS’ casing or ‘RS’ pipes as per specification and direction of the Engineer-in-charge.150 x 100 mm dia |
| 295 | Providing and fixing of housing clamp ( made with 12 mm thick MS sheet ) along with well cap (made with 10 mm thick MS sheet ) with necessary arrangements for SBDTW as per specification and direction of the Engineer - in - charge. 150 mm dia |
| 296 | Providing and shrouding of the deep tube well assembly with washed pea gravels ( 2.0 - 4.75 mm effective size ) as per specification ( IS : 4097) and direction of the Engineer - in - charge.with contractor's rigwith pea gravels obtained from Durgapur, West Bengal. |
| 297 | Providing and Installation of 3 HP (single/three phase) submerssible Pump (Electrical) as per relevent IS code with LT control panels connected with 100 mtr insulated cables from the distribution lines, 2 nos. electric pole of 8.5 mtr long 7/16 cable, well cap, housing clamp, column pipes, single/three phase earthing, motor starter, control panel box with locking arrangement with all accessories complete as per the direction fo the Engineer-in-charge.For Borewell |
| 298 | SEWAGE AND DRAINAGEProviding, laying and jointing glazed stoneware pipes grade ‘A’ with stiff mixture of cement mortar in the of 1:1 (1 cement: 1 fine sand) including testing of joints etc. complete 150 mm diameter |
| 299 | Laying Reinforced Cement Concrete Pipe NP2 as per design in single RowLaying reinforced cement concrete pipe NP2 for culverts on first class bedding of granular material in single row including fixing collar with cement mortar 1:2 but excluding cost of pipes (available at site), excavation, protection works, backfilling, concrete and masonry works in head walls and parapets as per MoRD Technical specification Clause 1106.900 mm dia |
| 300 | 600 mm dia |
| 301 | 300 mm dia |
| 302 | Constructing brick masonry chamber for underground C.I. inspection chamber and bends with 1st class bricks in cement mortar 1:4 (1 cement : 4 fine sand) C.I. cover with frame (light duty) 455x610 mm internal dimensions, total weight of cover with frame to be not less than 38 kg (weight of cover 23 kg and weight of frame 15 kg) R.C.C. top slab with 1:2:4 mix (1 cement :2 fine sand : 4 graded stone aggregate 20 mm nominal size) foundation concrete 1:5:10 (1 cement: 5 fine sand : 10 graded stone aggregate 40 mm nominal size), inside plastering 12 mm thick with cement mortar 1:3 (1 cement: 3 fine sand) finished smooth with a floating coat of neat cement on walls and bed concrete etc. complete as per standard design :Inside dimensions 600x 850 mm and 45 cm deep for pipe line with three or more inlets : |
| 303 | Making soak pit 2.5 m diameter 3.0 metre deep with 45 x 45 cm dry brick honey comb shaft with well burnt 2nd class bricks and S.W. drain pipe 100 mm diameter, 1.8 m long complete as per standard design. |
| 304 | Supplying and fixing C.I. cover without frame for manholes 500 mm diameter C.I. cover (medium duty) the weight of the cover to be not less than 58 kg. |
| 305 | Supply,Installation, Testing and Commissioning of Underground Fully Advanced Automatic Sewage Treatment Plant of Capacity of 20 KLD including solar packeg to run the plant on solar energy. |
| 306 | SOLID WASTE COMPOSTING PLANTSupply, Installation and Commissioning of Fully Automatic Electro-mechanically operated Organic Waste Composting machine capable of handling 150 kg/ day of with Duel shaft 3HP shredder 12-month warranty from the date of supply for parts against manufacturing defect |
| 307 | Bill No. XV: Electrical, CCtv, WiFi & Networking Works |
| 308 | Electrical PanelSupplying and laying of the following sizes XLPE insulated PVC sheathed aluminium conductor armoured cable with necessary connection etc as required2 core 10 Sq mm |
| 309 | 3.5 core 50 Sq mm |
| 310 | 3.5 core 95 Sq mm |
| 311 | 3.5 core 120 Sq mm |
| 312 | 3.5 core 185 Sq mm |
| 313 | 4 core 16 Sq mm |
| 314 | 4 core 25 Sq mm |
| 315 | Supplying and fixing of aluminium terminal ends (LUGS) - long barrel of following sizes : -10 sq mm |
| 316 | 16 sq mm |
| 317 | 25 sq mm |
| 318 | 50 sq mm |
| 319 | 95 sq mm |
| 320 | 120 sq mm |
| 321 | 185 sq mm |
| 322 | Supplying and fixing of heat shrinkable straight through cable jointing kits of following sizes : -2 core 16 sqmm or 4 core 10/16 sq mm size |
| 323 | 3.5 core or 4 core 25/35 sq mm size |
| 324 | 3.5 core or 4 core 50 sq mm size |
| 325 | 3.5 core or 4 core 95 sq mm size |
| 326 | 3.5 core or 4 core 185 sq mm size:- |
| 327 | Supplying and laying of following size DWC HDPE pipe ISI marked along with all accessories like socket, bend, couplers etc. conforming to IS 14930, Part II complete with fitting and cutting, jointing etc. in the existing trench, complete as required.63 mm dia (OD-63 mm & ID-51 mm nominal) |
| 328 | 160 mm dia (OD-160 mm & ID-135 mm nominal) |
| 329 | LT Panel :-Fabrication, supply, installation, testing and commissioning of cubicle type compartmentalized wall/ floor mounted power cum control panel board of specified size and 900mm (NS) deep made out of not less than 2 mm thick CRCA MS sheet with suitable size compartments for bus bars, switchgears and necessary cutouts for voltmeters, ameters ets as per specifications including powder coating painting but without busbars, switchgears and other accessories etc complete as required for completeness and as per attached specification, direction of Engineer, CPWD standards and Electrical Inspectorate standards. (Only face area is to be measured)INCOMER1 No.630A FP MCCB(35 KA) (1 for main incomer)4 pole MCCB, 600A, Adjustable Microprocessor Release, 35KA for D.G incomer - 1nosMetering & Indication2 set of phase indicating lamps2 set of (0-500V) Voltmeter with VSS1 set of (0-160A) Ammeter with ASS with 3 no s.160/5A CTs1 set of (0-200A) Ammeter with ASS with 3 no s.200/5A CTsBUS-BAR1 Set of 1000A TPN Aluminium Bus Bar with colour coded PVC SleevesOUTGOINGS 3 Nos.63 A FP MCCB (10KA) &2 Nos 160 A FP MCCB (10KA),2 Nos 200 A FP MCCB (10KA) |
| 330 | Fabrication, supply, installation, testing and commissioning of cubicle type compartmentalized wall/ floor mounted power cum sub main distribution board of specified size and depth above 300 mm and upto 450mm made out of not less than 2 mm thick CRCA MS sheet with suitable size compartments for bus bars, switchgears and necessary cutouts for voltmeters, ameters ets as per specifications including powder coating painting with busbars, switchgears and other accessories etc complete as required as following:. 4 pole MCCB, 200 A, 35KA (1no.)as incomer analog type 0-100 amp ammeter of size 100x100 (NS)analog type 0-500 amp voltmeter of size 100x100 (NS)selector switch for voltmeterselector switch for ammetermeter230 volt LED type indicating lamp (3nos.)100A-TP (MCB) (1 no.) 63A-TP (MCB) (4 no.), 40A-TP (MCB) (4),32A-DP (MCB)(4)for outgoing as outgoing |
| 331 | Fabrication, supply, installation, testing and commissioning of cubicle type compartmentalized wall/ floor mounted power cum sub main distribution board of specified size and depth above 300 mm and upto 450mm made out of not less than 2 mm thick CRCA MS sheet with suitable size compartments for bus bars, switchgears and necessary cutouts for voltmeters, ameters ets as per specifications including powder coating painting with busbars, switchgears and other accessories etc complete as required as following:. 4 pole MCCB, 160 A, 35KA (1no.)as incomer analog type 0-100 amp ammeter of size 100x100 (NS)analog type 0-500 amp voltmeter of size 100x100 (NS)selector switch for voltmeterselector switch for ammetermeter230 volt LED type indicating lamp (3nos.)63A-TP (MCB) (6 no.), 40A-TP (MCB) (4),32A-DP (MCB)(4)for outgoing as outgoing |
| 332 | Design, Fabrication, Supply, Erection, Testing and commisioning of Powder coated, Weather Proof Double door type Feeder pillar fabricated out of 14 guage CRCA sheet steel in cubical, free standing, dust and vermin proof, with reinforcement of suitable size angle iron, channel, T -iron or flats as required. Feeder pillar shall be treated with all anti-corrosive process before painting as per specification. Feeder Pillar shall be suitable for 415V, 3-Phase, Four wire, 50 Hz supply complete with earth bus and lifting hooks as required in case of large panels.Approval shall be taken for each panel before fabrication.direction of Engineer, CPWD standards and Electrical Inspectorate standards. (All hardwares like nuts and bolts used shall be Galvanized and Zinc passivated)- Feeder Pillar:INCOMER- 1No. 63A FP MCCB(35 KA) , 1No. 63A FP Contactor, AOM switch & Timers for 24 Hrs. settingMetering & Indication- 1 set of phase indicating lampsBUS-BAR- 1 Set of 100A TPN Aluminium Bus Bar with colour coded PVC Sleeves.OUTGOINGS-10 Nos. 32A FP MCB, 4 Nos. 40A FP MCB and 4 Nos. 6-32 SP MCB |
| 333 | Supplying, installation, testing and commissioning of following capacity diesel Generating Set (alternator directly coupled to diesel engine) compete in all respect broadly comprising of following and as per CPCB 2 norms (upto date ammended), including following specification.A. Alternator : Self excited, brush less type, of following capacity, 3 phase, 415 volts 50 Hz, 4 pole, AC alternator complete with all accessories.B. Engine : water cooled diesel engine of suitable BHP for rated alternator at 1500 rpm, turbo charged, direct injection type, 4 stroke, 4/6 cylinder including specified size fuel tank of approved design and shape duly calibrated and painted with one coat of primer and two coats of synthetic enameled paint of approved colour, residential type silencer with exhaust MS pipe (upto 2metre beyond silenser) duly wrapped with asbestos rope of legging of specified quality and specification.C. AMF Panel Cubical, compartmentalized, AMF panel board with all suitable size power and control contactors, switches, meters and other accessories, internal wiring, connection, inter-connection etc. for trouble free smooth functioning of DG Set complete with battery charger and leads as per specification.D. Base Plate : Common base plate of required size for mounting of engine alternator set fabricated from MS channel and vibration damping arrangement with cushy foot mounting i/c painting etc. as per specification. 250 KVA |
| 334 | Supply, Installation, Testing and Commissioning of Distribution Transformer (3ISLevel- ll)-DTR 200KVA 11/0.433KV as per TSECL Standards and Specification and providing all necessary connections as per the instructions of Engineer-in-charge. |
| 335 | Internal Electrical WorkWiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS/HFFR PVC insulated copper conductor single core cable in surface/ recessed medium class PVC conduit, with modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm FRLS/HFFR PVC insulated copper conductor single core cable etc. as required. Group A |
| 336 | Group B |
| 337 | Group C |
| 338 | Wiring for twin control light point with 1.5 sq.mm FRLS/HFFR PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit, 2way modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm FRLS/HFFR PVC insulated copper conductor single core cable etc. as required. |
| 339 | Wiring for light/ power plug with 4X4 sq. mm FRLS/HFFR PVC insulated copper conductor single core cable in surface/ recessed medium class PVC conduit along with 2 Nos. 4 sq. mm FRLS/HFFR PVC insulated copper conductor single core cable for loop earthing as required. |
| 340 | Wiring for circuit/ submain wiring along with earth wire with the following sizes of FRLS/HFFR PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required. 2 X 1.5 sq. mm + 1 X 1.5 sq. mm earth wire |
| 341 | 2 X 2.5 sq. mm + 1 X 2.5 sq. mm earth wire |
| 342 | 2 X 4 sq. mm + 1 X 4 sq. mm earth wire |
| 343 | 4 X 6 sq. mm + 2 X 6 sq. mm earth wire |
| 344 | 4 X 10 sq. mm + 2 X 6 sq. mm earth wire |
| 345 | Supplying and drawing following pair 0.5 mm dia FRLS/HFFR PVC insulated annealed copper conductor, unarmored telephone cable in the existing surface/ recessed steel/ PVC conduit as required.Telephone wire 2 pair |
| 346 | Telephone wire 4 pair |
| 347 | Supplying and drawing co-axial TV cable RG-6 grade, 0.7 mm solid copper conductor PE insulated, shielded with fine tinned copper braid and protected with PVC sheath in the existing surface/ recessed steel/ PVC conduit as required. |
| 348 | Metal Telephone Junction Box 10 / 20 / 30 Pair |
| 349 | Supplying and fixing of the following PVC conduit (medium gauge) with all accessories on slab/recessed on wall etc as required.19/20 mm dia |
| 350 | 25 mm dia |
| 351 | Supplying and fixing of the following electrical accessories including necessary connection etc. as required.Angle/batten holder |
| 352 | Ceiling rose |
| 353 | Supplying and fixing of the following sizes GI (in recess) and plastic (on surface) modular switch boards etc. as required.1-2 module GI switch board:- |
| 354 | 3 module GI switch board:- |
| 355 | 4 module GI switch board:- |
| 356 | 6 module GI switch board:- |
| 357 | 8 module GI switch board:- |
| 358 | 12 module GI switch board:- |
| 359 | Supplying and fixing of the following sizes modular type cover plates for GI/Plastic modular switch boards etc. as required.1-2 module :- |
| 360 | 3 module :- |
| 361 | 4 module :- |
| 362 | 6 module :- |
| 363 | 8 module :- |
| 364 | 12 module :- |
| 365 | Supplying and fixing of the following modular accessories including necessary connection etc. as required.6/10 amps one way SP switch (1M) |
| 366 | 6/10 amps two way SP switch (1M) |
| 367 | 16/20 amps one way SP switch (1M) |
| 368 | Bell push SP (1M) |
| 369 | 32 amps one way DP switch (2M) |
| 370 | 3 pin 6/10 amps socket outlet (2M) |
| 371 | 3/6 pin 16/20 amps socket outlet (2M) |
| 372 | 3/6 pin 25 amps socket outlet (2M) |
| 373 | 5 step fan regulator (2M):- |
| 374 | RJ11 telephone socket outlet (1M):- |
| 375 | RJ45 LAN socket outlet (1M):- |
| 376 | TV socket outlet (1M):- |
| 377 | Buzzer call bell (1M) |
| 378 | 20/25 amps single phase motor starter switch (2M) |
| 379 | Supply, Installation, Testing and Commissioning of 1200MM ceiling fan with Brush Less Direct Current (BLDC) Motor, class of insulation: B, 3 nos. metal (Aluminium alloy) blades, 30 cm long down rod, 2 nos. canopies,hackle kit, safety rope, copper winding, steel/Al body.Power Factor not less than 0.9, Service Value(CM/M/W) minimum as below, 350 RPM (tolerance asper IS : 374-2019), THD (Total Harmonic Distortion) less than 10%, remote (preferably mobile app based)for speed control and all remaining accessories including safety pin, nut bolts, washers, temperature rise=75 0C (max.), insulation resistance more than 2mega ohm, suitable for 230 V, 50 Hz, single phase AC supply Ceiling Fan compliant to IS 374:2019 fan i/cexternal connections with 1.5 sq.mm FRLS/HFFR,PVC insulated copper conductor single core cableand earthing etc. as required.1200mm, service value ≥ 6.0 CM/Min/Watt, air delivery 210 CM/Min (Minimum) |
| 380 | Providing and fixing circular/ Hexagonal cast iron or M.S. sheet box for ceiling fan clamp of internal dia 140mm, 73mm height, top lid of 1.5mm thick M.S. sheet with its top surface hacked for proper bonding, top lid shall be screwed into the cast iron/ M.S. sheet box by means of 3.3mm dia. round headed screws, one lock at the corners. Clamp shall be made of 12mm dia M.S. bar bent to shape, including painting the exposed portion as per standard drawing complete as required (provided incase of low ceiling height) |
| 381 | Supplying & installation of 225/230 mm sweep metalic body exhaust fan including connection etc as required:- |
| 382 | SOLAR WATER HEATING SYSTEMSupplying, installation, testing and commissioning of following of solar water heating system with heat exchanger type including electrical heater backup,make up water tank but without piping including necessary connection etc as required. |
| 383 | Supplying and fixing of following surface/recess mounted LED luminaries in powder coated die cast housing complete with high efficiency polycarbonate diffuser and necessary connection etc. as required (with 50000 burning hours and minimum lumen output of 100 lm/watt):-Surface mounted integrated 10 watt LED batten with polycarbonate diffuser:- |
| 384 | Surface mounted integrated 20 watt LED batten with polycarbonate diffuser:- |
| 385 | Recessed/Surface mounted 2ft x 2ft decorative 36 watt LED panel light with integral driver and high quality polycarbonate diffuser:- |
| 386 | Recessed round/Square shaped 6 watt LED downlight with integral driver and high quality polycarbonate diffuser |
| 387 | Recessed round/Square shaped 18 watt LED downlight with integral driver and high quality polycarbonate diffuser:- |
| 388 | Supplying and fixing of following outdoor LED luminaries in powder coated die cast housing complete with heat resistant tempered glass/diffuser including necessary connection etc. as required (50000 burning hours and minimum lumen output of 100 lm/watt):-9 watt/10 watt LED Bollard light with high quality polycarbonate diffuser (IP 65):- |
| 389 | 6 watt/10 watt LED Bulkhead light with high quality polycarbonate diffuser (IP 65):- |
| 390 | Supplying and installation of powder coated steel sheet enclosure (MCB DB) suitable for 240/415 volts MCB/Isolator/RCCB (SP/SPN/DP/TP/TPN/FP) complete with necessary bus bar, neutral link, din rail, earth bar etc i/c connection as required.(2+4) / 6 way SPN MCB DB (double door) |
| 391 | 6 way horizontal TPN MCB DB (Double door):- |
| 392 | 8 way horizontal TPN MCB DB (Double door):- |
| 393 | Supplying & installation of 10 KA breaking capacity, B/C curve MCB of following ratings in the existing MCB DB including connection as required:-6 to 32 amps SP MCB:- |
| 394 | 40/50/63 amps TPN MCB:- |
| 395 | Supplying, installation, testing and commissioning of following ratings online UPS with inbuilt isolation transformer, 50/60Hz (Auto sensing) frequency, P.F range 0.95-0.99, voltage regulation +/-1%, Pure sine wave form, total harmonic distortion < 5% with full load, Noise level 50db at 1m, LED indication for Normal mode/Load on battery/Load on bypass/System fault, Audible alarm for Mains failure, low battery, Overload, fault and Bypass mode complete with M. S Rack for mounting battery bank, Battery inter link cables and all other necessary accessories including connections etc. as required:-10 kVA, 3 Ph input/1 Ph output Online UPS with 28800 VAH battery bank for minimum 2 hours Backup:- |
| 396 | SITC of 43-inch or above LED Display, Resolution : 3840*2160 (4K UHD), Brightness (Typ.): 350 nits or better Contrast Ratio : 5000:01:00 or better, Viewing Angle (H/V) :178/178 Response Time (G-to-G) :8ms(Typ.) or better, Operation Hour : 16/7,Haze : 2%, Input : DVI-D, HDMI 2.0 (2), HDCP 2.2, Stereo Mini Jack, DVI/HDMI/Audio (Common), USB 2.0 x 2, Output : Stereo Mini Jack,RS232C (in/out) thru stereo jack, RJ45,IR Special Features : H/W: Temperature Sensor, Pivot Display, Clock Battery (168hrs Clock Keeping), Built in Speaker(10W 2ch or better), IP5x, Wi-Fi/BT S/W: Auto Source Switching & Recovery, Button Lock, Hot key option, Plug&Play (Initial Setting) remote control etc with wall mounting bracket. |
| 397 | Supplying and fixing following of split Inverter type Air Conditioner unit with cooling unit (copper coil) and condensing unit (copper coil) including 5 years compressor warranty and standard length of upto 5 metre of copper piping with insulation etc complete as per specification:2.0 Ton split type Inverter AC {5 Star} |
| 398 | Supplying and fixing following Small Fridge, Big Space : Fitted with a bottle bin that accommodates 2-litre bottles and a wire shelf to easily organize items mini bar freeze 40 litre as required |
| 399 | Supplying following grade co-axial TV cable FR PVC insulated, shielded with fine tinned copper braid and protected with PVC sheath cable in company pack coils.RG-11 grade |
| 400 | Suppy, installation, testing & commissitioning and putting into operation and final testing of MACHINE ROOM LESS TYPE automatic lift complete with ARD and all standard equipments, accessories and control equipments as per manufacturer's design and as per CPWD specification (Part III LIFTS) 1981and fulfilling following requirments on turn key basis.A. Type : Passenger liftB. Load : 6 passenger/ 408 KgC. Speed : 1.0 metre per secondD. Contol : AC2E. Operation : Microprosser based simplex collective selective with/without lift attendentF. Total rise : About 9 mtrsG. Landings : 4 All on same sideH. Floors served : G,1,2,3I. Signals : Digital car position indicator, car travel direction indicator in car & at all landingsJ. Lift shaft size : About 1800 mm width X 1680 mm depth, finished with plaster (size as per actual site conditions)K. Lift car size : About 1100 mm width X 1000 mm depthL. Car entrance : Clear opening 800 mm wide X 2000 mm high protected with car doorM. Landing entrance: Clear opening 800 mm wide X 2000 mm high protected with landing doorN. Car door : Stainless steel/ Glass Door two pannel telescopic/centre opening flush typeO. Landing door : Stainless steel/ Glass Door two pannel telescopic/centre opening flush typeP. Door operation: Automatic electric power operated door with infra red protectionQ. Car interior : Stainless steel pannel with hair line/ mirror/moon rock finish on all sidesR. Car floor : Hard wood covered with PVC/ marblex tilesS. Car ceiling & lighting : Fluorscent lighting concealed by suspended false ceiling with plain acrylic diffuser. The frame of suspended false ceiling shall be of powder coated aluminiumT. Car ventilation : Pressure fan with anodised aluminium grillU. Emergency lighting in car: Battery operated Emergency lighting in the lift carV. Intercom system : Battery operated Intercom system in lift car, machine room and control roomW. Emergency alarm : Battery operated alarm bell system in lift car & contol roomX. Electric power supply : AC 415 Volts 3 phase 50 Hz terminated in machine roomY. Fire man switch : Fire man switch at main landing termanal |
| 401 | External lightsEarthing with 40 mm dia G.I. Earth pipe (medium gauge) 4.5 m. long complete with masonry enclosure on top CI cover plate size 12\\"x 12\\" having locking arrangement including CC work, holes on earth pipe etc. as required. |
| 402 | Extra for using salt (5 kg) and charcoal (46kg) for pipe earth electrode as required. |
| 403 | Earthing with Copper earth plate 600 mm x 600 mm x 3 mm thick i/c accessories and providing masonry enclosure with CI cover plate Size 12\\"x 12\\" having locking arrangement, along with 20 mm dia (medium gauge) watering pipe including CC work etc as required:- |
| 404 | Earthing with G.I. earth plate 600 mm x 600 mm x 6 mm thick i/c accessories and providing masonry enclosure with CI cover plate Size 12\\"x 12\\" having locking arrangement, along with 20 mm dia (medium gauge) watering pipe including CC work etc as required:- |
| 405 | Proving and fixing / drawing of 4.06 mm dia (8 SWG) G.I. wire on surface or in existing G.I/ PVC/ Polythene pipe for loop earthing as required. |
| 406 | Supply and fixing of 25mm x 5mm GI strip on wall/ floor of the building for horizontal/ vertical run including necessary spacers and porcelain insulators at regular intervals. |
| 407 | Supply and fixing of 32mm x 6 mm GI strip on walls/ floor of the building for horizontal/ vertical run including necessary spacers and porcelain insulators at regular intervals. |
| 408 | Supply and fixing of 25mm x 3mm Copper on walls/ floor of the building for horizontal/ vertical network including necessary spacers and porcelain insulators at regular intervals. |
| 409 | Supply and fixing of 32mm x 6 mm Copper strip on walls/ floor of the building for hoizontal/ vertical network including necessary spacers and porcelain insulators at regular intervals. |
| 410 | Supplying and fixing of following outdoor LED luminaries in powder coated die cast housing complete with heat resistant tempered glass/diffuser including necessary connection etc. as required (50000 burning hours and minimum lumen output of 100 lm/watt):-45 watt LED street light fixture with integral driver and secondary lens (IP 66):- |
| 411 | 60 watt LED flood light fixture with integral driver and secondary lens (IP 66):- |
| 412 | 120 watt LED flood light fixture with integral driver and secondary lens (IP 66):- |
| 413 | 9 watt/10 watt LED Bollard light with high quality polycarbonate diffuser (IP 65):- |
| 414 | 6 watt/10 watt LED Bulkhead light with high quality polycarbonate diffuser (IP 65):- |
| 415 | 40 watt LED post top light fixture with integral driver and high quality polycarbonate diffuser (IP 65):- |
| 416 | Providing and fixing of lightning conductor finial, made of 25 mm dia 300 mm long, G.I. tube, having single prong at top, with 85 mm dia 6 mm thick G.I. base plate including holes etc. complete as required. |
| 417 | Providing and fixing testing joint, made of 20mm. x 3mm. thick G.I. strip, 125mm. long, with 4 nos of G.I. bolts, nuts, chuck nuts and spring washers etc. complete as required. |
| 418 | Supply installation and commissioning of contemporary design Single arm Lighting Pole with 60WX1 LED Modules of 6000mm Height, arm length 1000mm, made out of hot rolled steel grade E250, as per IS 2062:2011 and designed suitably for wind speed upto 50m/s wind conforming to IS 875: PART -3:1987. the square base plate of MS (grade E250) and facilitated with 4 elongated slots 48mm x 24mm at CC 215X160mm to suit the 500mm, J-type bolts (Grade 4.6). The cable entry hole Ø70mm is provided at the centre of the baseplate. A base compartment for weather proof control box is provided at a height 300mm above the base plate with a die cast door contoured to the poles's shape housing the gear tray, pre-wired with 2.5 Sq.mm cable, Siemens/Anchor make MCB, terminal connectors for loop in loop out arrangement. The surface preparation of the pole & components shall be done by shot blasting which is environmentally safe eliminating the chemical and acid use and ensuring the thorough removal of impurities like rust, oxides and other unwanted particles from the surface for high standard coating. The surface finish of the pole shall be Zinc rich primer coat & pure polyester powder coating providing 60 Microns DFT. Pole consist of module based luminaire each 60W(Min IP68) with minimum delivered lumens of 110lm/W with led life span of L70 / B10 @ 60000 Hrs, SDCM ≤ 3, Type III light distribution, IK09, Input Voltage 240V ac at 50-60Hz frequency, Operating voltage 100-277V ac with cut-off protection and self restart feature in case of over / under voltage and phase to phase voltage, driver efficiency > 85%, Power factor >0.9, THD <10% . Available CCT 3000K/4000K/5700K. Product finsih available: Pure polyester powder coated Product should be BIS and CE Certified. |
| 419 | Supply installation and commissioning of Lighting Pole of 4000mm Height suitable for mounting light luminaires Poles can stylishly convey the identity of any landscape. , made out of hot rolled steel grade E250, as per IS 2062:2011 and designed suitably for wind speed upto 50m/s wind conforming to IS 875: PART -3:1987. The pole profile extends from the square base plate of MS (grade E250) and, J-type, M16 bolts (Grade 4.6). The cable entry hole Ø70mm is provided at the centre of the baseplate. The pole size shall have Ø76 mm and base size Ø139.7 mm. A base compartment for weather proof control box is provided at a height 260mm above the base plate with a die cast door contoured to the poles's shape housing the gear tray, prewired with 2.5 Sq.mm cable, Siemens/Anchor make MCB, terminal connectors for loop in loop out arrangement. The surface preparation of the pole & components shall be done by shot blasting which is environmentally safe eliminating the chemical and acid use and ensuring the thorough removal of impuritise like, rust, oxides and other unwanted particles from the surface for high standard coating. The surface finish of the pole shall be Zinc rich primer coat & pure polyester powder coating providing 60 Microns DFT. Any other wiring/electrical consumables shall be under the scope of purchaser. Product finsih available: Pure polyester powder coated Graphite grey, Anthracite grey, black. Product should be CE Certified. |
| 420 | Supply installation and commissioning of double arm Lighting Pole 4000mm Height. Made out of hot rolled steel grade E250, as per IS 2062:2011 and designed suitably for wind speed upto 50m/s wind conforming to IS 875: PART -3:1987. the square base plate of MS (grade E250) of size and facilitated with 4 elongated slots 38mm x 19mm at CC 180mm to suit the 300mm, J-type bolts (Grade 4.6). The cable entry hole Ø70mm is provided at the centre of the baseplate. A base compartment for weather proof control box is provided at a height 300mm above the base plate with a die cast door contoured to the poles's shape housing the gear tray, pre-wired with 2.5 Sq.mm cable, Siemens/Anchor make MCB, terminal connectors for loop in loop out arrangement. The surface preparation of the pole & components shall be done by shot blasting which is environmentally safe eliminating the chemical and acid use and ensuring the thorough removal of impurities like rust, oxides and other unwanted particles from the surface for high standard coating. The surface finish of the pole shall be Zinc rich primer coat & pure polyester powder coating providing 60 Microns DFT. Any other wiring/electrical consumables shall be under the scope of purchaser. Product should be CE Certified. |
| 421 | Supply installation and commissioning of an elegant and efficient 30W Lantern with translucent diffuser provide a unique comfortable light choice with symmetrical and glare free light distribution. Aesthetically designed sturdy construction ensure a long life against all weather condition, maintaining initial performance through lifetime of installation. The luminaire compromises of specially contoured spun aluminium top cover. The lamp along with control gear is housed inside and covered with a toughened glass diffuser at the top portion of extruded aluminium tube and the bottom portion attached to a mounting base. Lamp compartment encased in non-yellowing clear/ translucent UV stabilised acrylic diffuser. Die cast aluminium spigot base with aluminium alloy of low copper content for effective corrosion resistance. Suitable for mounting on 60mm OD Pipe. Integral constant power supply. Product benefits are elegant, robust design, environmental friendly, moisture proof, insect free, low maintenance cost, reduces glare with minimum delivered lumens of 120lm/W with led life span of L70-B10-60000h@ Ta 25°C Mac Adam step 3 LED, IP65, IK06, CRI≥80, Power factor >0.95, THD<10, Surge Protection upto 4KV, driver efficiency >87%. Input Voltage 240V ac at 50-60Hz frequency, Operating voltage 100-277V ac with cut-off protection. Available CCT 3000K/4000K/5700K. Product should be BIS and CE Certified. |
| 422 | Supply installation and commissioning of 16w environmentally friendly LED garden and pathway luminaires to create a pleasant light distribution with a high degree of visual comfort. Theses luminaires offer shielded glare free illumination on ground surface and are perfect for illuminating entrance, footpaths as well as garden and landscape architecture. Clean lines and pure form are the underlying elements if this series of LED bollards, designed to provide radially symmetric light emission of 360° . Luminaire body made of extruded aluminium alloy (grade 6063) with die cast aluminium components and non corrosive SS fasteners. Reflector system made of spun aluminium (powder coated). Non yellowing UV stabilised acrylic/ polycarbonate diffuser. Silicone gasket. Luminaire supplied with2/3 core cable length and IP67 connector. Mounting plate die cast aluminium double powder coated with an anchorage unit and stainless steel fixing screws. High luminous efficiency at reduced wattage. Elegant and robust design, dark sky compliant protects pedestrians from glare by preventing spill light above the horizontal plane. Cable entries for through wiring of main supply cable. Integral constant current power supply , pre-wired with LED driver and suitable for operating on 240V 50 Hz single phase AC supply. Lumen output 120lm/w, Mac Adam step 3 LED, CRI>80, L70-B10-60000h@ Ta 25°C, IK08, IP65. Power factor >0.95, THD<8, Surge Protection upto 3KV, driver efficiency >87%. Operating Temperature of the luminaire is -15°C~ 50°C, Input Voltage 240V ac at 50-60Hz frequency, Operating voltage 100-277V ac with cut-off protection. Available CCT 3000K/4000K/5700K. Product should be BIS and CE Certified. |
| 423 | Supply installation and commissioning of Flexible LED Strip White led color 12Vdc / 24Vdc CRI >80 MacAdam step 3 Input power : 12W Dimension 1000 x 12 mm Beam angle : 120° Electronic driver ON/OFF (External driver)IP rating IP67MATERIAL CHARACTERISTICSCopper coated flexible strip, Silicone moulded diffuser, End cap LIGHTING PERFORMANCESilicone moulded diffuserThis luminaire contains built-in LED modules. LED modules are engineered accordingly to the existing regulations of Lumen Maintenance (LM80) and Technical Memorandum (TM21), Lifespan of the luminaire >10,000 hours at 40ｰC. Operating ambient temperature range is from -15ｰC to +50ｰC. Driver efficiency >85%, Surge protection 3KV. Product should be BIS and CE Certified. |
| 424 | SITC of 4 Mtr. GI OCTAGONAL POLE FABRICATED PART AS PER DIMENSION : T0P DIA - 70 mm, BOTTOM DIA -135 mm, (SECTION LENGTH - 4000 mm) THICKNESS - 3 mm, BASE PLATE -- 220 mm x 220 mm x 12 mm.. FOUNDATION BOLT - M20 x 700 mm x 4 nos 'J' type bolts |
| 425 | Supply of 1 mtr Single Arm Bracket. |
| 426 | Supply of 1 mtr Double Arm Bracket. |
| 427 | CCTV WORKSupplying, installation, testing and commissioning of 4 MP Bullet Camera weather & dust proof IP based Fixed Lens day/night Camera (IP67, IK 10), 1/3” 4MP PS CMOS Image Sensor, H.265 and H.264 triple-stream encoding, WDR(120dB), Day/Night Support, UL ,CE FCC Certified as per the specifications. |
| 428 | 2 MP PTZ Camera - Providing installation testing and commissioning weather & dust proof IP based Dome PTZ (Pan Tilt & Zoom) true day & night camera, 1/2.8” 2MP PS CMOS Image sensor, Max. 50/60fps@1080P, Color: [email protected]; [email protected] (IR on), Powerful 45x (3.95~177.7 mm) Optical and 16x Digital zoom, WDR(120dB), 3D DNR, Day/Night(ICR),Defog, ROI, EIS, AGC, BLC, HLC, Support Starlight Function, Up to 300 presets, auto scan, 8 tour, 5 pattern, auto pan, Tripwire, Intrusion, Abandoned / Missing , Face Detection, Heat Map, IR Range of 200 Mtr., Max 300° /s pan speed, 360° endless pan rotation, Built-in 7/2 alarm in/out, Micro SD card 256GB, IP67, IK10, Support PoE+, UL, CE ,FCC certified |
| 429 | Supply, Installation, Testing and Commissioning of 32 Channel NVR 4 Sata port-Upto 8 TB; 32 Channel IP camera input, Quad Core embedded Processor and LINUX Embedded; 16 POE; Max 200 Mbps incoming & out going bandwidth, Smart H.265/ H.264 codec decoding, Upto 8 MP resolution preview and playback, Frame Rate: 1-15 FPS(8 MP); 1-25/30 fps for rest of Resolutions; Support 4 SATA HDDs up to 8 TB each, 2 USB (1 USB 3.0, 1 USB2.0), 1HDMI /1 VGA simultaneous video output , Two way talk 1Channel Input, 1Channel Output RCA, 1RJ-45port (10/100/1000Mbps), |
| 430 | Supplying, installation, testing and commissioning of 8 Port Managable PoE Switch 10/100/1000 8 Port with 2 Giga SFP uplink, L2 Managed PoE switch, Power Budget max 96 W, single port 30 W, AI Extend, Al VLAN as per the specifications. |
| 431 | Supplying , installation , testing and commissioning of 9U Indoor Rack Wallmount 9U 630D With Front Glass Door Lock & Key 550 9U - (with 1U cable Manager;Fan;6 socket PDU) complete as required. |
| 432 | Supplying , installation , testing and commissioning of 6 TB Surveillance Hard disk drive Complete as required |
| 433 | Supplying and drawing UTP 4 pair Cat 6 LAN wire in existing surface/concealed Steel/FRLS PVC conduit as per specification. |
| 434 | Supply, installation and testing for HDMI cable. |
| 435 | Supply of swaged steel tubular pole as per IS 2713 with base plate of size 300x300x6mm welded at bottom, necessary hole for cable entry and earthing stud welded at specified height including painting with one coat of red oxide zinc chromate primer.Designation 410 SP-2 height 7.00 metre |
| 436 | Supply, installation, testing and commissioning of 2MP Outdoor IP66 PTZ Camera with 4.5-135 mm Lens, 120dB WDR, 30X Optical Zoom, 100 Meter IR Range, ONVIF Profile S & G PTZ Camera, CE FCC and UL certified as per specification of Engineer in charge. |
| 437 | Supplying, installation testing and commissioning of standard/ short/long throw multimedia projector with display device- DLP technology and above, minimum No. of pixels 1024x768, computer compatiblity- UXGA/WXGA/SXGA/XGA, minimum life of light source-5000 hours, network terminal wired/ wireless with inbuilt speaker including all accessories and specifications as per site requirement.Brightness: 4000 Lumens |
| 438 | Supplying and fixing of the following PVC conduit (medium gauge) with all accessories on slab/recessed on wall etc as required.25 mm dia |
| 439 | Erection of metallic pole of following length in cement concrete 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 40 mm nominal size) foundation including excavation and refilling etc. as required.Above 6.5 metre and upto 8.0 metre |
| 440 | Wi-fi and Network Active componentInRoom APSITC Ruckus Wi-Fi 6 dual-band concurrent 2.4 GHz & 5 GHz, Wired / Wireless Wall Switch, BeamFlex+, 1 10/100/1000 & 2 10/100/1000 Ethernet Access Ports, POE in. Does not include DC power supply. |
| 441 | SITC Surface Mount Bracket for Ruckus H350/H550. Required when mounting H350/H550 where no electrical outlet box is available |
| 442 | Indoor APSITC Ruckus R350 dual-band 802.11abgn/ac/ax Wireless Access Points, 2x2:2 streams (2.4GHz/5GHz) OFDMA, MU-MIMO, BeamFlex+, 802.3af PoE support. Does not include power adapter or PoE injector. Includes Limited Lifetime Warranty |
| 443 | SITC Multipurpose mounting bracket for R-Series indoor AP’s. Supports mounting to hard wall, ceiling, pole or truss |
| 444 | Outdoor APSITC Ruckus T350c, omni, outdoor access point, 802.11ax 2x2:2 internal BeamFlex+, dual band concurrent. One Ethernet port, PoE input. -20°C to 65°C Operating Temperature. Includes mounting bracket. Does not include PoE injector. |
| 445 | SITC Mounting Kit for T-Series APs (see RUCKUS Accessory Guide for compatibility) - Qty 1 |
| 446 | 24 Port POE SwitchSITC ICX 8100 Switch, 24x 10/100/1000 ports, 4 x 1G SFP uplink-ports, advanced layer 2, 370W PoE budget |
| 447 | SITC WD SPT-8100-SGD-48/48-X/24P/24P-X 3YR RMT |
| 448 | Core SwitchSITC RUCKUS ICX 8200 Switch, 24x 10/100/1000 Mbps SFP ports, 4x 25 GbE SFP28 stacking/uplink-ports, three-year remote TAC support. Power cord not included. TAA |
| 449 | SITC ICX 8200 Layer 3 premium license. Enables advanced layer 3 features (OSPF, VRRP, PIM, PBR, VRF, GRE) |
| 450 | SITC 1000Base-SX SFP optic, MMF, LC connector, Optical Monitoring Capable |
| 451 | Ruckus Cloud ControllerSITC RUCKUS One Single-tenant Essentials cloud 1 x license of Device Networking for 3-Yr Subscription for REC. License owned by Ruckus End Customer. Device Networking of AP or Switch use 1 x license each. Switch RMT support is not included and is required to be purchased separately. |
| 452 | SITC Palo Alto 440 |
| 453 | Bill No. XVI: Fire Fighting & Fire Alarm Work |
| 454 | Providing laying, testing & commissioning of 'C' class heavy duty MS Pipe conforming to IS 1239/3589 i/c fittings like elbows, tees, flanges, tapers, nuts bolts, gaskets etc. in ground including welding, excavation & providing cement concrete blocks as supports, anticorrosive treatment with coaltar/asphalt tape as per IS 10221, refilling the trench etc. of following sizes complete as required.200 mm dia |
| 455 | 150mm dia. |
| 456 | Providing, laying, testing & commissioning of 'C' class heavy duty MS pipe conforming to IS 3589/IS 1239 including Welding, fittings like elbows, tees, flanges, tapers, nuts bolts, gaskets etc. and fixing the pipe on the wall/ceiling with suitable clamp/support frame and painting with two or more coats of synthetic enamel paint of required shade complete as required :25 mm dia |
| 457 | 80mm dia. |
| 458 | 100 mm dia |
| 459 | 150 mm dia |
| 460 | Applying priming coat [Payment shall be made after submission of Test Certificate issued by the Manufacturer] :With ready mixed red oxide zinc chromate primer of approved brand and manufacture on steel galvanised iron/ steel works |
| 461 | Providing and fixing C.I. double acting air valve of approved quality with bolts, nuts, rubber insertions etc. complete (The tail pieces, tapers etc if required will be paid separately):80 mm dia |
| 462 | Supplying, fixing, testing & commissioning of double flanged sluice valve of rating PN 1.6 with non rising spindle, bronze/gun metal seat, ISI marked complete with nuts, bolts, washers, gaskets and conforming to IS 780 of following sizes as required :100 mm dia |
| 463 | 150mm dia. |
| 464 | 200 mm dia. |
| 465 | Providing, installation, testing and commissioning of non-return valve of following sizes confirming to IS: 5312 complete with rubber gasket, GI bolts, nuts, washers etc.as required 100 mm dia |
| 466 | 150mm dia |
| 467 | 200 mm dia. |
| 468 | Supplying, fixing, testing and commissioning of butterfly valve of PN 1.6 rating with bronze / gunmetal seat duly ISI marked complete with nuts, bolts, washers, gaskets conforming to IS 13095 of following sizes as required :100 mm dia |
| 469 | 150mm dia |
| 470 | 200 mm dia. |
| 471 | Supply, installation, testing and commissioning of ball valve (brass) high or low pressure with plastic floats inclusive of all necessary required material, labor for mentioned below size.20.00 mm OD |
| 472 | 25.00 mm OD |
| 473 | Providing and fixing gunmetal single acting air release valve with screwed inlet 25 mm dia and with necessary G.I. coupling, valve to be fitted on top of Air vessel or on wet riser as per specification. |
| 474 | Supplying and fixing first-aid Hose Reel with MS construction spray painted in post office red, conforming to IS 884 complete with the following as required.(a) 20 mm nominal internal dia water hose thermoplastic (Textile reinforced) type -2 as per IS:12585(b) 20 mm nominal internal dia gun metal globe valve & nozzle.(c) Drum and brackets for fixing the equipmets on wall.(d) Connections from riser with 25 mm dia stop gun metal valve & M.S. Pipe and socket.30 m |
| 475 | Supplying and fixing single headed internal hydrant valve with instantaneous Gunmetal / Stainless Steel coupling of 63 mm dia with cast iron wheel ISI marked conforming to IS 5290 (Type -A) with blank Gunmetal / Stainless Steel cap and chain as required :Single headed Gunmetal |
| 476 | Supplying and fixing orifice plate made out of 6 mm thick stainless steel (Grade 304) with orifice of required size to be fitted between flange & landing valve of external and internal hydrants to reduce pressure at the outlet to the level of 3.5 kg/cm2 complete as required. |
| 477 | Supplying and fixing 63 mm dia, 15 mtr long Flax canvas hose pipe with 63 mm dia Male and Female Stainless Steel-IS: 3444 Grade-1 couplings duly binded with GI wire, rivets etc. conforming to IS: 636 (Type -A) as required. |
| 478 | Supplying and fixing of MS hose cabinet box of made of 2 mm thick MS sheet and 40 x 40 x 5mm angle iron with front openable cover having 6 mm thick glazed glass viewing window i/c necessary locking arrangement, on existing wall / brick platform etc complete as required.Size 600 mm x 600 mm x 500 mm |
| 479 | Providing and fixing fire brigade 63mm dia GM suction coupling to 100/150 mm dia suction pipe complete. |
| 480 | Providing and fixing standard fireman's axe (tested for 20000 Volts) with heavy insulated rubber handle. (ISI marked) |
| 481 | Supply & Fixing of galvanized mild steel fire bucket of 10 litres nominal capacity. Bucket shall be painted with two coats of white paint on the inside and two coats of red paint on the outside etc complete as required. |
| 482 | Supplying and fixing of fire brigade connection of cast iron body with gun metal male instantaneous inlet couplings complete with cap and chain as reqd. for suitable dia MS pipe connection conforming to IS 904 as required :4 way - 150 mm dia M.S. Pipe |
| 483 | Providing and laying in position cement concrete of specified grade excluding the cost of centring and shuttering -1:3:6 ( 1 Cement: 3 fine sand : 6 graded stone aggregate 20 mm nominal size) |
| 484 | Reinforced cement concrete work in beams, suspended floors, roofs having slope upto 15° landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases upto floor five level excluding the cost of centring, shuttering, finishing and reinforcement1:1:2 ( 1 Cement: 1 fine sand : 2 graded stone aggregate 20 mm nominal size) |
| 485 | Reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete above plinth level.Thermo-Mechanically Treated bars of grade Fe-500D or more |
| 486 | Centering shuttering including struttings, propping etc. and removal of form work for:Foundations, footings, bases for columns etc. for mass concrete with steel formwork |
| 487 | UGR (UNDER GROUND RESERVIOR)Excavation for all types and sizes of foundations, trenches and drains or for any other purpose including disposal of excavated stuff with complete lead and lift including dressing and leveling of pits. - All kinds of soil |
| 488 | Filling from available excavated stuff (Excluding rock) in trenches, plinth, sides of foundation etc. in layers not exceeding 20cm in depth consolidating each deposited layer by ramming and watering with a lead upto 50 M. and lift upto 1.5 M. |
| 489 | Providing and laying in position cement concrete of specified grade excluding the cost of centring and shuttering -1:3:6 ( 1 Cement: 3 fine sand : 6 graded stone aggregate 20 mm nominal size) - PCC for tank |
| 490 | Providing and laying in position specified grade of reinforced cement concrete excluding the cost of centring, shuttering, finishing and reinforcement - All work upto plinth level:1:1:2 ( 1 Cement: 1 fine sand : 2 graded stone aggregate 20 mm nominal size) |
| 491 | Extra for providing and mixing water proofing material in cement concrete work in doses by weight of cement as per manufacturer's specification |
| 492 | Centering shuttering including struttings, propping etc. and removal of form work for:Foundations, footings, bases for columns etc. for mass concrete with steel formwork |
| 493 | Walls (any thickness) including attached pilasters, buttresses, plinth and string courses etc. using shuttering ply (For retaining wall) |
| 494 | Reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete above plinth level.Thermo-Mechanically Treated bars of grade Fe-500D or more |
| 495 | Extra for providing and mixing water proofing material in cement plaster work in proportion recommended by the manufacturers. |
| 496 | Providing and Placing in position suitable PVC water stops conforming to IS:12200 for construction/expansion joints between two RCC members and fixed to the reinforcement with binding wire before pouring concrete etc. complete as required as per direction of the Engineer-in-charge:Serrated with central bulb (225 mm wide, 8-11 mm thick) |
| 497 | Providing orange colour safety foot rest of minimum 6 mm thick plastic encapsulated as per IS : 10910 on 12mm dia steel bar conforming to IS : 1786 having minimum cross section as 23 mmx25mm and over all minimum length 263 mm and width as 165mm with minimum 112 mm space between protruded legs having 2 mm tread on top surface by ribbing or chequering besides necessary and adequate anchoring projections on tail length on 138 mm as per standard drawing and suitable to with stand the bend test and chemical resistance test as per specifications and having manufacture's permanent identification mark to be visible even after fixing, including fixing in manholes with 30x20x15 cm cement concrete block 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) complete as per design. |
| 498 | Supplying and fixing C.I. cover without frame for manholes : 455 x 610 mm rectangular C.I. cover (light duty)the weight of the cover to be not less than 23 kg. |
| 499 | Providing, hoisting and fixing in position inverted „J‟ type 100 mm dia. C.I. Cowl type ventilators with mosquitoproof aluminium mesh at top including applying 2 coats of anti-corrosive paint, etc. complete as directed by Engineer-in-charge, weighing not less than 35 Kg. |
| 500 | Providing and laying flanged C.I. standard specials such as tees, bends, collars, tapers, caps etc., suitable for flanged jointing as per IS : 1538 : Upto 300 mm dia |
| 501 | Pump HouseProviding and laying in position cement concrete of specified grade excluding the cost of centring and shuttering -1:3:6 ( 1 Cement: 3 fine sand : 6 graded stone aggregate 20 mm nominal size) |
| 502 | Providing and laying in position specified grade of reinforced cement concrete excluding the cost of centring, shuttering, finishing and reinforcement - All work upto plinth level:1:1:2 ( 1 Cement: 1 fine sand : 2 graded stone aggregate 20 mm nominal size) |
| 503 | Reinforced cement concrete work in beams, suspended floors, roofs having slope upto 15° landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases upto floor five level excluding the cost of centring, shuttering, finishing and reinforcement1:1:2 ( 1 Cement: 1 fine sand : 2 graded stone aggregate 20 mm nominal size) |
| 504 | Extra for providing and mixing water proofing material in cement concrete work in doses by weight of cement as per manufacturer's specification |
| 505 | Providing and fixing in position MS Puddle collar (approx. 1m length) inside the wall including all material labour as per Technical Specifications and as per direction of Engineer. 300 mm dia. Pipe |
| 506 | Providing and fixing Galvanized chicken mesh (24 guage, 12 mm size) properly stretched and nailed ensuring equal thickness of plaster at junction of masonry work and concrete members. |
| 507 | Providing and fixing M.S. grills of required pattern in frames of windows etc. with M.S. flats, square or round bars etc. all complete.Fixed to steel windows by welding. |
| 508 | Providing and fixing in position 1mm thick M.S. sheet sliding-shutters with frame and diagonal braces of 40x40x6mm angle iron and 3mm M.S. gusset plates at the junction and corners 25mm dia pulley, 40x40x6mm angle and T-iron guide sufficiently long at the top and bottom respectively, channels & with bolts, nuts, rivets, locking arrangement, stoppers, handles, hold fast including embedding in cement concrete of required grade for fixing in position, all necessary fittings, including applying a priming coat of approved steel primer etc. complete as required. |
| 509 | Providing and fixing 1mm thick M.S. sheet door with frame of 40x40x6mm angle iron and 3mm M.S. gusset plates at the junctions and corners, & with cleats with bolts & nuts, rivets, locking arrangement, handles, hooks & eyes, pinlets including embedding in cement concrete of required grade for fixing in position, all necessary fittings, including applying a priming coat of approved steel primer etc. complete as required:-Using M.S. angels 40x40x6 mm for diagonal braces. - Door |
| 510 | Supplying and fixing rolling shutters of approved make, made of required size M.S. laths interlocked together through their entire length and jointed together at the end by end locks mounted on specially designed pipe shaft with brackets, side guides and arrangements for inside and outside locking with push and pull operation complete including the cost of providing and fixing necessary 275mm long wire springs grade No.2 and M.S. top cover of required thickness for rolling shutters & with handles, hold fast including embedding in cement concrete of required grade required for fixing in position, all necessary fittings, including applying of approved steel primer etc. complete as required:80xl.25mm M.S. laths with 1.25 mm thick top cover. |
| 511 | Providing and fixing ball bearing for rolling shutters (exceeding 10 sqm area) of approved make complete as required. |
| 512 | Extra for providing & fixing mechanical device chain and crank operation for operating rolling shutters of approved make complete as required:-Exceeding 10.00 sqm and upto 16.80 sqm in the area. |
| 513 | Distempering with 1st quality acrylic distemper (ready mixed) having VOC content less than 50 grams/ litre, of approved brand and manufacture to give an even shade [Payment shall be made after submission of Test Certificate issued by the Manufacturer] :New work ( two or more coats) over and including water thinnable priming coat with cement primer. |
| 514 | Finishing walls with acrylic smooth exterior paint of required shade of approved brand and manufacture [Payment shall be made after submission of Test Certificate issued by the Manufacturer] :New work ( two or more coats applied @ 1.67 litre/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm) |
| 515 | Painting with synthetic enamel paint of approved brand and manufacture to give an even shade [Payment shall be made after submission of Test Certificate issued by the Manufacturer]:Two or more coats on new work |
| 516 | Grouting of Retaining wall in cement grouting mass as per direction of Engineer Incharge. |
| 517 | Providing, installation of Hand operated overhead traveling crane on turn key basis of capacity 2 Tonnes, all including Horizontal & longitudinal girder size: ISMB200, square bar for top of the longitudinal girder, the hoist & trolley, which traverses across the Horizontal & longitudinal and lifts up and down, two set of chain pulley (single girder type crane having Horizontal and longitudinal motion along the entire length of pump house.) including all material and labour etc. and commissioning as per Technical Specifications and as per direction of the engineer. Room size inner: 10.5m x 6.5m |
| 518 | Electrical Work Pump RoomSupplying & installation of 10 KA breaking capacity, B/C curve MCB of following ratings in the existing MCB DB including connection as required:-6 to 32 amps SP MCB |
| 519 | 6 to 32 amps FP MCB:- |
| 520 | Wiring for light/ fan/ exhaust fan/ call bell point with 2x1.5 sq. mm PVC insulated copper conductor cable (FR) in PVC conduit (medium gauge) recessed in slab/ wall complete with 6/10 amps modular type switch, cover plate, GI box including necessary connection etc. as required. |
| 521 | Wiring for Circuit/Sub-main with the following sizes PVC insulated Copper conductor cable (FR) in PVC conduit (medium gauge) recessed in slab/ wall etc. as required:-2 X 1.5 + 1 X 1.5 sq mm |
| 522 | 2 X 2.5 + 1 X 1.5 sq mm |
| 523 | 4 X 4 + 2 X 1.5 sq mm |
| 524 | 4 X 6 + 2 X 2.5 sq mm |
| 525 | Supplying & fixing of 1200 mm sweep white color AC ceiling fan with brush less dirrect current (BLDC) motor having class B insulation, power factor not less than 0.9 complete with 300 mm down rod, canopies, shackle kit, 3nos blades, safety rope including wiring the down rod with 2x1.5 sqmm PVC insulated copper conductor cable(FR) (BEE 5 star/minimum service value 6.0 m3/min/W & tolerance as per IS:374-2019) : - |
| 526 | Supplying and fixing of the following modular accessories including necessary connection etc. as required.5 step fan regulator (2M):- |
| 527 | Supplying and Installation of 300 mm sweep metalic body exhust fan including connection etc. as required. |
| 528 | Supplying and fixing of the following PVC conduit (medium gauge) with all accessories on slab/recessed on wall etc as reqd. - 20 mm |
| 529 | Supplying and fixing of the following sizes electrical acessries including necessary connections etc. as required.Ceiling Rose |
| 530 | Supplying and fixing of the following sizes GI (in recess) and plastic (on surface) modular switch boards etc. as required.1-2 module GI switch board:- |
| 531 | 3 module GI switch board:- |
| 532 | 4 module GI switch board:- |
| 533 | Supplying and fixing of the following sizes modular type cover plates for GI/Plastic modular switch boards etc. as required.1-2 module |
| 534 | 3 module |
| 535 | 4 module |
| 536 | Supplying and installation of powder coated steel sheet enclosure (MCB DB) suitable for 240/415 volts MCB/Isolator/RCCB (SP/SPN/DP/TP/TPN/FP) complete with necessary bus bar, neutral link, din rail, earth bar etc i/c connection as required.(2+4) / 6 way SPN MCB DB (double door) |
| 537 | 8 way horizontal TPN MCB DB (Single door):- |
| 538 | Supplying and fixing of following surface/recess mounted LED luminaries in powder coated die cast housing complete with high efficiency polycarbonate diffuser and necessary connection etc. as required (with 50000 burning hours and minimum lumen output of 100 lm/watt):-Surface mounted integrated 20 watt LED batten with polycarbonate diffuser |
| 539 | Supplying and laying of the following sizes XLPE insulated PVC sheathed aluminium conductor armoured cable with necessary connection etc as required.4 core 16 Sq mm |
| 540 | 3.5 core 50 Sq mm |
| 541 | 3.5 core 95 Sq mm |
| 542 | Supplying and fixing of aluminium terminal ends (LUGS) - long barrel of following sizes : -16 Sq. mm |
| 543 | 50 sq. mm |
| 544 | 95 sq. mm |
| 545 | Supplying and fixing of following Cable tray made of hot dip galvanised iron:-30 mm x 50mm:- |
| 546 | 54 mm x 100 mm |
| 547 | 105mm x 150mm |
| 548 | Mechanical Work For Pump HouseProviding, laying, testing & commissioning of 'C' class heavy duty MS pipe conforming to IS 3589/IS 1239 including Welding, fittings like elbows, tees, flanges, tapers, nuts bolts, gaskets etc. and fixing the pipe on the wall/ceiling with suitable clamp/support frame and painting with two or more coats of synthetic enamel paint of required shade complete as required :80 mm dia |
| 549 | 100 mm dia. |
| 550 | 150 mm dia. |
| 551 | 200 mm dia (wall thickness 6.3 mm) |
| 552 | 300 mm dia (wall thickness 7.1 mm) |
| 553 | Providing, installation, testing and commissioning of Circular Bellow, Grade: SS 304 section moulded to shape and fitted with a rotatable coated steel flange to each end for connection to flanged pipework. - 150 mm dia. |
| 554 | Providing and fixing ball valve (brass) of approved quality High or low pressure, with plastic floats complete : - 25 mm nominal bore. |
| 555 | Providing and fixing C.I. double acting air valve of approved quality with bolts, nuts, rubber insertions etc. complete (The tail pieces, tapers etc if required will be paid separately):50 mm dia. |
| 556 | Providing and fixing C.I. dirt box strainer for bulk type water meter with nuts, bolts, rubber insertions etc. complete conforming to IS : 2373 : 200 mm dia. |
| 557 | Providing, installation, testing and commissioning of stainless steel Y-strainer fabricated out of 1.6 mm thick stainless steel, Grade 304, sheet with 3 mm dia holes with stainless steel flange.100 mm dia |
| 558 | 150 mm dia |
| 559 | Supplying, fixing, testing and commissioning of butterfly valve of PN 1.6 rating with bronze / gunmetal seat duly ISI marked complete with nuts, bolts, washers, gaskets conforming to IS 13095 of following sizes as required : 150 mm dia |
| 560 | 200 mm dia |
| 561 | 300 mm dia. |
| 562 | Providing, installation, testing and commissioning of non-return valve of following sizes confirming to IS: 5312 complete with rubber gasket, GI bolts, nuts, washers etc.as required :80 mm dia |
| 563 | 150 mm dia. |
| 564 | 200 mm dia. |
| 565 | Providing and fitting fixing of pressure meter ( 0.0 - 14.0 Kg/ sqcm.) as per specification and as per specification and the direction of the Engineer - in-charge. |
| 566 | Supplying and installing pressure gauge of 100 mm Ø., 0-300 PSI or 0-21 kg per cm square fitted with 12/15 mm Ø. pad cock valve, and G.I. pipe, elbow etc. as per requirement in approved manner. |
| 567 | (a) Supplying, installation, testing and commissioning of Electric driven Main Fire Pump conforming to IS 12469: 2019 suitable for automatic operation and consisting of following, complete in all respects, as required :(b) Horizontal type, multistage, centrifugal, split casing pump of cast iron body & bronze impeller with stainless steel shaft, mechanical seal as required.(c) Suitable HP Squirrel cage induction motor, TEFC, synchronous speed 1500 RPM, suitable for operation on 415 volts, 3 phase 50 Hz, AC supply with IP 55 protection for enclosure, horizontal foot mounted type with Class-'F' insulation, conforming toIS-12615: 2018.(d) M.S. fabricated Common base plate, coupling, coupling guard, foundation bolts etc. as required. (e)Suitable cement concrete foundation duly plastered with anti vibration pads.2280 lpm at 70 m Head, |
| 568 | (a) Supplying, installation, testing and commissioning of diesel engine driven main fire pump conforming to IS 12469: 2019 suitable for automatic operation and consisting of following, complete in all respects, as required : (Diesel Driven Pump)(b) Horizontal type, multistage, centrifugal pump of cast of iron body and bronze impeller with stainless steel shaft, mechanical seal as required.(c) Suitable HP, 1500 RPM water cooled with radiator, diesel engine conforming to relevant IS standard complete with auto starting mechanism, 12 /24 volts electric starting equipment, diesel tank, exhaust pipe extended upto 10 m outside pump house duly insulated with 50 mm thick glass wool with 1.0 mm thick aluminium sheet cladding, residential silencer, instruments and protection as per standard specification, stop solenoid for auto stop in the event of fault with audio indications, painted with post office red colour etc. as required.(d) M.S fabricated, common base plate, coupling, coupling guard, foundation bolts etc. as required. (e) Suitable cement concrete foundation duly plastered and with anti vibration pads.2280 lpm at 70 m Head, |
| 569 | (a) Supplying, installation, testing and commissioning of electric driven pressurisationpump conforming to IS 12469: 2019 suitable for automatic operation and consisting of following, complete in all respects, as required : (Jockey Pump)(b) Horizontal type, multistage, centrifugal pump of cast iron body and bronze impeller with stainless steel shaft, mechanical seal as required.(c) Suitable HP squirell cage induction motor TEFC type suitable for operation on 415 volts, 3 phase 50 Hz AC supply with IP 55 class of protection for enclosure, horizontal foot mounted type with Class- 'F' insulation, conforming to IS-12615: 2018.(d) M.S. fabricated Common base plate, coupling, coupling guard, foundation bolts etc. as required.(e) Suitable cement concrete foundation duly plastered and with anti vibration pads.180 lpm at 70 m Head |
| 570 | Supplying and fixing air vessel made of 250 mm dia, 8 mm thick MS sheet, 1200 mm in height with air release valve on top and flanged connection to riser, drain arrangement with 25 mm dia gun metal wheel valve with required accessories, pressure gauge and paintingwith synthetic enamel paint of approved shade as required. |
| 571 | Dewatering pump: Supplying, installation, testing and commissioning of auto on/off Drainage Submersible Pump (2 no's) (DPK.10.50.075.5.0D) suitable for single phase, 230 volts AC supply including connection of suction and delivery line etc. , (Q= 14 cum/hr., Head = 10m), including of control panel 2P 3PH 8A auto GIDPC auto on/off, complete as required in all respect as per technical specification and as per direction of Engineer. |
| 572 | Supply, Installation, Testing & commissioning of factory assembled of fuel tank, 220 ltrs, battery charger panel - 12V including all necessaries accessories complete as per technical specification and as per direction of Engineer. |
| 573 | Supplying, installation, testing and commissioning of following ratings Valve regulated lead acid(VRLA) battery with all accessories including necessary connections etc. as required:-12 V/ 180AH tall tubular/ flat plate Battery:- |
| 574 | Supply, Installation, Testing & commissioning of control Fire Panel: Including auto / Manual Operation Considered, Individual Pressure Switch is and pressure transmitter considered for each Pump, Potential Free Contacts for On / Off and Trip of each Pump Considered for BMS, Indoor / Basement Mounted Enclosure Considered, Cable Bottom Entry Considered, One Voltmeter and Individual Ammeter considered and MCCB considered at incomer etc. complete as per technical specification and as per direction of Engineer. |
| 575 | Supply, Installation, Testing & commissioning of Cable with level switch 10m length complete as per technical specification and as per direction of Engineer. |
| 576 | Supply, installation, testing & commissioning Battery for Fire Panel and as per direction of Engineer. |
| 577 | Terrace (Booster) PumpsSupplying, installation, testing and commissioning of electric driven terrace pump suitable for automatic operation and consisting of following, complete in all respects, as required: (Terrace Pump)(a) Horizontal type, multistage, centrifugal, split casing pump of cast iron body & bronze impeller with stainless steel shaft, mechanical confirming to IS : 1520b) Suitable HP squirell cage induction motor TEFC type suitable for operation on 415 volts, 3 phase, 50 Hz, AC supply with IP55 class of protection for enclosure, horiziontal foot mounted type with Class-'F' insulation, conforming to IS-325.(c) M.S.fabricated common base plate, coupling, coupling guard, foundation bolts etc.as required.(d) Suitable cement concrete foundation duly plastered and with anti vibration pads.450 lpm at 35 m Head |
| 578 | Supply, installation, testing and commissioning of cubicle type wall/ floor mounted power cum control panel made out of not less than 1.6 mm thick MS sheet and comprising of following panel mounting switchgears there in including connection inter-connection etc. as required.a) Phase indicating lamps with fuses and toggle switches 1 set b) Star-delta starter suitable for 7.5 HP 3 phase AC induction motor with over load and no volt relay c) 32 A \\"C\\" series TPMCB 1 No d) Voltmeter 0-500 V with selector switch 1 sete) Ammeter 0-10 A with CT's and selector switch 1 set. |
| 579 | Providing, laying, testing & commissioning of 'C' class heavy duty MS pipe conforming to IS 3589/IS 1239 including Welding, fittings like elbows, tees, flanges, tapers, nuts bolts, gaskets etc. and fixing the pipe on the wall/ceiling with suitable clamp/support frame and painting with two or more coats of synthetic enamel paint of required shade complete as required :100 mm dia. |
| 580 | Providing, installation, testing and commissioning of non-return valve of following sizes confirming to IS: 5312 complete with rubber gasket, GI bolts, nuts, washers etc.as required :100 mm dia. |
| 581 | Supplying, fixing, testing and commissioning of butterfly valve of PN 1.6 rating with bronze/gunmetal seat duly ISI marked complete with nuts, bolts, washers, gaskets conforming to IS 13095 of following sizes as required : 100 mm dia |
| 582 | Providing and fixing ball valve (brass) of approved quality High or low pressure, with plastic floats complete : 25 mm nominal bore |
| 583 | Providing & fixing of pressure switch in M.S. pipe line including connection etc. as required. |
| 584 | Terrace TankReinforced cement concrete work in walls (any thickness), including attached pilasters, buttresses, plinth and skirting courses, fillets, columns, pillars, piers, abutments, posts and struts etc. upto floor five level excluding cost of centring, shuttering, finishing and reinforcement-1:1:2 ( 1 Cement: 1 fine sand : 2 graded stone aggregate 20 mm nominal size) |
| 585 | Centering shuttering including struttings, propping etc. and removal of form work for:Walls (any thickness) including attached pilasters, buttresses, plinth and string courses etc. using shuttering ply (For retaining wall) |
| 586 | Suspended floors, roofs, landings, balconies and access platform with 12 mm thick shuttering ply |
| 587 | Columns, Pillars, Piers, Abutments, Posts and Struts with shuttering ply |
| 588 | Providing and Placing in position suitable PVC water stops conforming to IS:12200 for construction/expansion joints between two RCC members and fixed to the reinforcement with binding wire before pouring concrete etc. complete as required as per direction of the Engineer-in-charge:Serrated with central bulb (225 mm wide, 8-11 mm thick) |
| 589 | Extra for providing and mixing water proofing material in cement concrete work in doses by weight of cement as per manufacturer's specification |
| 590 | Grouting of Retaining wall in cement grouting mass as per direction of Engineer Incharge. |
| 591 | Providing orange colour safety foot rest of minimum 6 mm thick plastic encapsulated as per IS : 10910 on 12mm dia steel bar conforming to IS : 1786 having minimum cross section as 23 mmx25mm and over all minimum length 263 mm and width as 165mm with minimum 112 mm space between protruded legs having 2 mm tread on top surface by ribbing or chequering besides necessary and adequate anchoring projections on tail length on 138 mm as per standard drawing and suitable to with stand the bend test and chemical resistance test as per specifications and having manufacture's permanent identification mark to be visible even after fixing, including fixing in manholes with 30x20x15 cm cement concrete block 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) complete as per design. |
| 592 | Supplying and fixing C.I. cover without frame for manholes :455 x 610 mm rectangular C.I. cover (light duty)the weight of the cover to be not less than 23 kg. |
| 593 | Providing and laying flanged C.I. standard specials such as tees, bends, collars, tapers, caps etc., suitable for flanged jointing as per IS : 1538 : Upto 300 mm dia. |
| 594 | Fire extinguisherSupply & Fixing ISI marked (IS:13849) Portable Fire Exitnguisher, ABC type capacity 5 kg, finished externally with red enamel paint, complete in all respects including initial fill and wall suspension. Capacity 5 kg |
| 595 | Supply & Fixing ISI marked (IS:2878) Portable fire Extinguisher, Carbon-dioxide type flat base including valve, discharge hose of not less than 10 mm dia. min. 600 mm long & complete in all respects including initial fill with C02 gas confirming to IS:307-1966 filled to a filling ratio of not more than 0.667and wall suspension bracket. Capacity 4.5 Kg |
| 596 | Supply & Fixing ISI marked (IS:10204) Poratable Fire Exitnguisher, Trolley mounted Mech. Foam type capacity 09 ltrs with gun-metal cap and nozzle and complete respects in all respects including initial fill and wall suspension.Capacity 9.0 ltrs |
| 597 | Supply & Fixing of ISI marked (IS:2878) Fire Extinguisher, Trolley mounted, CO2 (gas pressure) type capacity 22.5 Kg. with gun-metal cap. And nozzle and complete in all respects including initial fill and wall suspension bracket.Capacity 22.5 Kg |
| 598 | Fire AlarmSupplying, installation, testing and commissioning of microprocessor based intelligent addressable main fire alarm panel, central processing unit with the following loop modules and capable of supporting not less than 240 devices (including detectors) and minimum 120 detectors per loopand loop length up to 2 km, network communication card,minimum 320 character graphics/ LCD display with touchscreen or other keypad and minimum 4000 events history login the non volatile memory (EPROM), power supply unit (230± 5% V, 50 hz), 48 hrs back-up with 24 volt sealedmaintenance free batteries with automatic charger. The panel shall have facility to connect printer to printout log and facility to have seamless integration with analog/digital voice evacuation system (which is part of the schedule of workunder SH: PA System) and shall be complete with allaccessories . The panel shall be compatible for IBMS systemwith open protocol BACnet/ Modbus over IP complete as perspecifications.Two Loop Panel |
| 599 | Supplying, installation, testing & commissioning of addressable manual call point complete as required. (Manual Break Glass ) |
| 600 | Supplying, installation, testing & commissioning response indicator on surface/recess MS box having two LEDs metallic cover complete with all connections etc. as required. |
| 601 | Supplying, installation, testing & commissioning of fault isolator complete with base as required. |
| 602 | Supplying, installation, testing & commissioning of addressable fire control module complete as required. |
| 603 | Supplying, installation, testing & commissioning of Repeater panel with 320 character/ Touch screen LCD display with inbuilt reset, acknowledge and silence swithes complete as required. |
| 604 | Supplying, installation, testing & commissioning talk back slavestation in surface / recess suitable for operation on simplexmode complete with P.T.T. knob & speaker / microphone enclosed in a M.S.(16 SWG)/ ABS box with break glass in frontetc. complete as required. |
| 605 | Supplying, installation, testing & commissioning of heat detector oprating at 54 °C/57 °C with rate of rise cum fixed tempreture (dual thermistor) type with mounting base complete with all conection etc. as required. |
| 606 | Supplying, installation, testing & commissioning of addressable horn cum strobe complete as required. (Analog addressable Hooter for alarm/evacuation signal) |
| 607 | Supplying, installation, testing & commissioning of smoke detector with builtin LED and mounting base complete with all connections etc. as required. |
| 608 | Supplying, installation, testing & commissioning of intelligentanalog addressable photothermal detector complete withmounting base complete as required. |
| 609 | Providing and fixing FRLS Armoured Cable from individual flow switches on each floor to annunciation panel installed in fire control room in basement including sleeves, cable clips, supports for horizontal runs making connection to each switch complete.4 core 2.5 Sqmm |
| 610 | Supply, installation, testing and commissioning of Gong Bell Unit with tapping, pipes, Valves, interconnecting hoses and pipings complete as required to make it operational. |
| 611 | Supply, installation, testing & commissioning of UPS (1 KVA) with two-hour Power Backup and other required accessories. |
| 612 | Supplying, installation, testing & commissioning of SITC of UL listed and FM approved Intelligent adressable class X type (style 7) input output module with polarity-insensitive technology and in-built dual isolator, tri-color LED for status (Green for normal, Yellow for faulty & Red for activation). Integral single-pole, double-throw (SPDT) relay on Model HTRI-R (up to 4 amps). Two wire operation and dynamic supervision complete with base as required. |
| 613 | Supplying, installation, testing & commissioning of SITC of UL38 listed, ROHS compliant & FM approved Intelligent adddressable class X (Style 7) Single Action Manual Pull Station. The MCP should be polarity-insensitive and have multi-color status LED. The MCP have in-built isolator for better reliability, circuit integrity and advance fault finding complete with base as required. |
| 614 | Bill No. XVII: Goods |
| 615 | Supply and Providing 3 Burner Cooking Stove - |
| 616 | Supply and Providing SS Working Table Type 1 |
| 617 | Supply and Providing 3 Bowl Kitchen Sink - |
| 618 | Supply and Providing GI Hood Kitchen Exhaust with Filter - |
| 619 | Supply and Providing Gi hood Duct Line |
| 620 | Supply and Providing SS Working Table Type 2 |
| 621 | Supply and Providing 5 HP Exhaust Fan |
| 622 | Supply and Providing SS Kitchen Rack |
| 623 | Supply and Providing Double Door Cooler of 850 Litre Capacity |
| 624 | Supply and Providing Double Door Deep Freezer of 320 Litre Capacity |
| 625 | Bharat AC001 10 KW Charger(3 Socket)Installation and Commissioning of Bharat AC001 10 KW Charger(3 Socket)One time on-boarding setup charges of Bharat AC001 10 KW Charger(3 Socket) |
| 626 | AC Level -2 Charger 7.4 KWInstallation and Commissioning of AC Level -2 Charger 7.4 KWInstallation and Commissioning of AC Level -2 Charger 7.4 KW |
| 627 | DC Fast Charger CCS-2 30 KW Single GunInstallation and Commissioning of DC Fast Charger CCS-2 30 KW Single GunOne time on-boarding setup charges of DC Fast Charger CCS-2 30 KW Single Gun |
| 628 | DC Fast Charger CCS-2 40 KW Double GunInstallation and Commissioning of DC Fast Charger CCS-2 40 KW Double GunOne time on-boarding setup charges of DC Fast Charger CCS-2 40 KW Double G |
| 629 | Bill No. XVIII: Furniture |
| 630 | Providing wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in position : Sal Wood |
| 631 | Providing and fixing specified wood frame work consisting of battens 50x25mm fixed with rawl plug and drilling necessary holes for rawl plug etc. including priming coat complete.Kiln seasoned and chemically treated hollock wood |
| 632 | French spirit polishing [Payment shall be made after submission of Test Certificate issued by the Manufacturer]:Two or more coats on new works including a coat of wood filler. |
| 633 | Providing and fixing flat pressed 3 layer particle board medium density exterior grade (Grade I) or graded wood particle board IS : 3087 marked to frame, backing or studding with screws etc. complete. (Frames, backing or studding to be paid separately): 12 mm thick |
| 634 | 18 mm thick |
| 635 | Providing and fixing aluminium tee channels (heavy duty) with rollers, stop end in pelmets as curtain rod. |
| 636 | Providing & Fixing decorative high pressure laminated sheet of plain / wood grain in gloss / matt / suede finish with high density protective surface layer and reverse side of adhesive bonding quality conforming to IS : 2046 Type S including cost of adhesive of approved quality.1.5 mm thick |
| 637 | Providing and fixing Pre-laminated medium density fibre board conforming to IS: 14587:1998 marked, with one side decorative lamination and other side balancing lamination Grade-I(exterior grade), in shelves with screws and fittings wherever required, edges to be sealed with PVC edge bending tape 2.00 mm thick of approved brand (fittings to be paid separately)25 mm thick |
| 638 | Providing and fixing chromium plated brass 50 mm cupboard or wardrobe knobs with nuts complete. |
| 639 | Providing and fixing powder coated telescopic drawer channels 300mm long with necessary screws etc. complete as per directions of Engineer-in-charge. |
| 640 | Providing and fixing in position wall panelling at all heights with 6 mm thick BWP ply board lapping with 4 mm thick Teak Veneer of approved quality in outer face, decorative teak wood bead (50 x 40 ) at top and skirting (150 x 25), comprising of a frame made from especially fabricated galvanised mild steel sheet 0.50 mm thick pressed section (galvanizing @120 grams per sqm including both sides) i.e.vertical studs of size 48 x 34 x 36 mm are placed at 600mm center to center in a floor and ceiling channel section of size 50 x 32m fixed to the floor and soffit at 600mm centers using 12mm dia,50mm long wedge type expanded zinc alloy dash fastner with 10mm bolt. This same channel is then to be fixed in horiziontal direction at 600mm center to center so as to form a grid of 600mm x 600mm. Glasswool of 50mm thickness is then to be inserted in the slots and finally ply board are to be screw fixed with self tapping pan head nickel coated mild steel screws of size 13 x 3.2mm all complete as per manufacturer's specification as per direction of Engineer-in-Charge all complete. |
| 641 | Providing and fixing stainless steel fancy handle of approved make fixed with SS screws etc. complete as per direction of Engineer-in-charge. 200 mm |
| 642 | Providing and supplying Unbranded Wooden Chair of approved quality, design, and make, made from seasoned hardwood (such as teak / rubberwood / beech wood or equivalent), suitable for office, visitor, or general seating use, conforming to the following specifications and requirements, complete as directed by the Engineer-in-Charge. |
| 643 | Providing and supplying Star Homz Cotton Mattress, factory-made, of approved make and quality, weighing not less than 12 kilograms, conforming to the following technical specifications, complete as directed by the Engineer-in-Charge. |
| 644 | Providing and supplying STAR HOMZ Cotton Mattress weighing 12 kilograms (±5%), manufactured from high-quality long-staple cotton properly carded and layered, enclosed in a cotton / woven fabric cover of approved shade and pattern.The mattress shall be uniformly filled, well-quilted, and neatly stitched on all sides to retain shape and firmness during use. All materials used shall be clean, hygienic, and free from synthetic fibre or impurities. The mattress shall be comfortable, durable, and suitable for regular institutional / domestic use.Type: Cotton Mattress – 12 KgComplete in all respects as per manufacturer’s specifications and directions of Engineer-in-Charge. |
| 645 | Providing and supplying Star Homz Pillow Cover, made from Khadi fabric conforming to IS:13717/1993, of approved shade and quality, size 59 cm (±0.5 cm) × 33 cm (±0.5 cm), neatly stitched and finished, complete as directed by the Engineer-in-Charge. |
| 646 | Providing and supplying unbranded dining table of approved design and size, made from seasoned hardwood / MDF / engineered wood, with golden finish or coating, complete as directed by the Engineer-in-Charge. |
| 647 | Providing and supplying L-shaped Reception Table, make Keshav’s (Keshav Enterprises) or equivalent approved, of modern modular design, ergonomically constructed from high-quality materials, with durable finish, cable management provisions, and smooth edges, complete in all respects as directed by the Engineer-in-Charge. |
| 648 | Providing and supplying Computer Table with Additional Unit, make AARIHANT CRAFT – GLOBAL MARKETING or approved equivalent, made from high-quality pre-laminated boards with modern design, durable hardware, and fine finish, suitable for office, computer lab, or home workstation use, complete as directed by the Engineer-in-Charge. |
| 649 | Providing and supplying SAGAR SHREE FURNITURE Aluminium Powder-Coated Wicker Furniture, made of high-grade Aluminium frame (min. 1.2 mm thick) with polyester powder coating (min. 60 microns), woven with 100% virgin HDPE synthetic wicker (UV stabilized, all-weather resistant). Cushions made of high-density polyurethane foam (min. 32D) covered with 180 GSM polyester acrylic outdoor fabric, UV- and water-resistant. All fasteners of Stainless Steel (Grade 304). Furniture shall be weather-proof, corrosion-resistant, and suitable for outdoor use.Finish: Smooth, uniform, and scratch-resistant.Color and design as approved by Engineer-in-Charge.The item shall conform to relevant IS standards (IS:13871, IS:12775, ASTM G154).Complete in all respects as per manufacturer’s specifications and directions of Engineer-in-Charge. |
| 650 | Providing and supplying Single-Seater Sofa (1 Seater) of DURIAN make or equivalent approved brand, suitable for office, reception, or lounge use, as per the direction of the Engineer-in-Charge.The sofa shall be ergonomically designed, aesthetically elegant, and made of durable, high-quality materials to ensure comfort, stability, and long service life. |
| 651 | Providing and supplying High-Back Revolving Chair, ergonomically designed with adjustable seat height and 360° revolving mechanism, mounted on a five-star nylon / metal base with twin-wheel castors for smooth mobility.Chair fitted with gas lift for height adjustment, tilt tension mechanism with locking system, and PU-moulded seat and back cushions upholstered with breathable fabric or mesh of approved shade.Backrest to be high-back type with lumbar support; armrests made of durable polypropylene / PU-padded material.All components shall be rust-free, sturdy, and smoothly finished for long operational life.Type: High-Back Revolving Chair with Adjustable Height and WheelsComplete in all respects as per manufacturer’s specifications and directions of Engineer-in-Charge. |
| 652 | Providing and supplying Chair made of 100% Virgin Polypropylene (injection moulded one-piece monoblock type) of approved colour and design, suitable for all, ergonomically designed with smooth edges, stackable, non-toxic, UV-stabilized, rustproof and easy to clean, as per direction of Engineer-in-Charge. |
| 653 | Providing and supplying INTEGRITY SQUARE Cafeteria Chair with Armrest, having an ergonomically contoured seat and back made of injection-moulded virgin polypropylene (PP) / high-grade plastic of approved colour and finish, supported on a sturdy powder-coated / chrome-plated tubular steel frame of suitable gauge.The chair shall be fitted with integrated or fixed armrests, anti-skid nylon leg caps, and all welds shall be smoothly ground and rust-protected.The unit shall be lightweight, stackable, durable, corrosion-resistant, and easy to maintain, suitable for cafeteria, canteen, or public seating applications.Type: Cafeteria Chair with ArmrestComplete in all respects as per manufacturer’s specifications and directions of Engineer-in-Charge. |
| 654 | Providing and supplying Unbranded Wooden Modern Dining Table, made from seasoned and chemically treated hardwood / engineered wood (MDF / particle board / plywood) with laminated or melamine-polished surface finish of approved shade and texture. The table shall be of modern design, sturdy construction, and smooth edges, supported on solid wood / metal legs with anti-skid buffers.All joints shall be glued and screwed, surfaces smoothly finished and sealed, and materials shall conform to relevant IS standards for furniture manufacture.The table shall be durable, termite-resistant, and easy to maintain.Make: Unbranded (as approved by Engineer-in-Charge)Type: Wooden Modern Dining TableComplete in all respects as per specifications and directions of Engineer-in-Charge. |
| 655 | Providing and supplying Door Curtains, made from premium woven fabric (minimum 260 GSM) in off-white colour, manufactured using high-quality yarn on handloom / powerloom, ensuring uniform texture, smooth finish, and colour fastness.Curtains shall be stitched with interlocked seams, hemmed edges, and fitted with eyelets or curtain tape as required for hanging. Fabric shall conform to IS:13717/1993 (Curtain and Upholstery Fabric – Cotton/Blended) standards. The material shall be washable, shrink-resistant, fade-resistant, and suitable for long-term institutional use. Type: Door Curtain, 260 GSM, Off-White ColourComplete in all respects as per manufacturer’s specifications and directions of Engineer-in-Charge. |
| 656 | Providing and supplying Floor Standing Display Cabinet, fabricated from seasoned hardwood or high-quality engineered wood (MDF / particle board / plywood) of approved make and finish. Cabinet to have fully glazed doors made with 5 mm thick clear float glass fitted in wooden / engineered wood frame, with concealed hinges, magnetic catch, and lockable handle arrangement. The internal structure shall include adjustable shelves, polished / laminated on all visible surfaces with scratch- and stain-resistant finish of approved shade. The base shall be sturdy with level-adjustable legs or skirting for floor stability. All edges to be smoothly finished, and hardware (hinges, handles, screws) to be of stainless steel or equivalent corrosion-resistant material. Type: Floor Standing Display Cabinet with Glass in Wood / Engineered Wood Frame Door Complete in all respects as per approved design, manufacturer’s specifications, and directions of Engineer-in-Charge. |
| 657 | Providing and supplying Drawer Type Steel Filing Cabinet, fabricated from prime quality CRCA (Cold Rolled Close Annealed) steel sheets of minimum 0.8 mm thickness for body and 1.0 mm for drawers, duly powder-coated (minimum 50–60 microns) in approved shade. Cabinet to be of standard office design, having multiple pull-out drawers (2/3/4-drawer type as specified) mounted on heavy-duty ball bearing telescopic slides for smooth and noiseless operation.Each drawer shall have a label holder, recessed handle, and central locking system to secure all drawers simultaneously. All edges and corners shall be rounded and free from burrs, and the unit shall rest on adjustable levelling glides.The cabinet shall be durable, rust-resistant, and suitable for foolscap / A4-size file storage. Material Finish: Powder-coated steel in grey / beige / approved colour.Type: Drawer Type Steel Filing CabinetComplete in all respects as per manufacturer’s specifications and directions of Engineer-in-Charge. |
| 658 | Providing and supplying Low-Back Chair with Fixed Armrest and Padding, constructed with an ergonomically designed low-back frame made of tubular steel / metal section of suitable gauge, fitted with fixed armrests of polypropylene or PU material. Seat and back to be upholstered with high-density foam padding (minimum 32D for seat, 28D for back) and covered with fabric / leatherette upholstery of approved colour and shade. The chair shall have a rigid welded structure, anti-skid leg caps, and smooth, durable finish with powder coating (minimum 50 microns). All joints shall be strong, burr-free, and neatly finished. The chair shall be comfortable, sturdy, and suitable for office / institutional / visitor seating. Type: Low-Back Chair with Fixed Armrest and Padding Complete in all respects as per manufacturer’s specifications and directions of Engineer-in-Charge. |
| 659 | Providing and supplying Dressing Table with Cupboard and Open Shelves, made from seasoned hardwood / high-quality engineered wood (plywood / MDF / particle board) of approved make and finish. The unit shall consist of a mirror panel (minimum size 1200 mm × 450 mm) mounted on a sturdy wooden frame, integrated with a storage cupboard with hinged door(s) and open display shelves for utility items. All visible surfaces shall be laminated / melamine-polished / PU-coated in approved shade and texture. Edges shall be rounded and smoothly finished, and hinges, handles, and fittings shall be of stainless steel or other corrosion-resistant hardware. All joints shall be strongly fixed, neatly finished, and free from burrs or sharp edges. The dressing table shall be durable, termite-resistant, and aesthetically designed for residential or institutional use. Type: Dressing Table with Cupboard and Open Shelves Complete in all respects as per manufacturer’s specifications and directions of Engineer-in-Charge. |
| 660 | Provisional Sums Statutory payments to water resources, National Highways, State Highways, Indian Railways, Forest Department, Archaeological Survey of India and similar organizations, Provision towards costs associated with social safeguards, Network expansions if required beyond the present scope, Nalla crossings, any dismantling work, shifting of utilities and miscellaneous works.NOTE:It is a non-competitive amount and bidder should enter the sum INR 89,67,306 (Eighty - Nine Lakh Sixty - Seven Thousand Three Hundred Six ) without any alteration.Any other figure quoted in price bid will be ignored. The competent authority reserves the right to reject financial bids if provisional sum quoted is beyond the amount specified above. |
| 661 | Environment Management Plan (EMP) Cost |
| 662 | Environment cum Occupational, Health and Safety Officer (. Implementation Staff) |
| 663 | Compensatory plantation including complete activities such as pit digging, manure, planting, fencing/tree guard, watering, and maintenance |
| 664 | Mitigation Measures – Construction Phase |
| 665 | Consent for establishment and consent for operation from TSPCB |
| 666 | (i) Silt fencing, for both sediment control cum Noise control (The fencing shall serve as a temporary environmental management measure for sediment control by intercepting and retaining eroded soil and construction runoff, while also functioning as a noise-control barrier (acoustic enclosure) to reduce the transmission of construction-related noise to adjacent sensitive receptors) |
| 667 | Environmental Protection: Providing dust screens of minimum 4.0 m height around construction sites/work zones using approved HDPE/green netting fixed to barricades or supporting frames, including all fixtures, supports, maintenance, replacement, and removal after completion of works, as per standard specifications.(5 times use considered) |
| 668 | (iv) Oil & grease traps (at parking) |
| 669 | Monitoring Measures (Pre construction and Construction Phase) |
| 670 | Air quality monitoring (1 pre-construction and 1 in every quarter except monsoon for 2 yrs) |
| 671 | Noise level monitoring(1 pre-construction and 1 in every quarter except monsoon for 2 yrs) |
| 672 | Surface water monitoring(1 pre-construction and 1 in every quarter except monsoon for 2 yrs) |
| 673 | Groundwater monitoring(1 pre-construction and 1 in every quarter except monsoon for 2 yrs) |
| 674 | Soil quality monitoring(1 pre-construction and 1 in every quarter except monsoon for 2 yrs) |
| 675 | Operation Phase |
| 676 | Air quality monitoring (Frequency 1 sample /year for 2 years) |
| 677 | Noise level monitoring (Frequency 1 sample /year for 2 years) |
| 678 | Surface water monitoring (Frequency 1 sample /year for 2 years) |
| 679 | Treated wastewater (STP) (Frequency 1 sample /year for 2 years) |
| 680 | Groundwater monitoring (Frequency 3 sample /year for 2 years) |
| 681 | Treated water Quality (Frequency 1 sample Half-yearly for 2 years) |
| 682 | Soil quality monitoring (Frequency 1 sample /year for 2 years) |
| 683 | Capacity Building & Training |
| 684 | Worker induction & safety training (Every Month for 24 months) Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Sep 21, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedOct 12, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 4 daysOct 12, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 4 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender