Tender For Construction Of Farmers Advisory Centre Cum Agriculture Sub-Seed Store At Krishnapur Under Teliamura Agri. Sub-Division, Khowai Tripura
Tender Value
41.16 Lakhs
Estimated cost
Bid Submission
30 Sep 2026
6 days left
EMD
82333
Bank guarantee accepted
Document Fee
1000
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Khowai → Tripura
EMD Exemption
Not Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for Construction Of Farmers Advisory Centre Cum Agriculture Sub-Seed Store At Krishnapur Under Teliamura Agri. Sub-Division, Khowai Tripura
BOQ
| Sl. No. | Item Description |
| 1 | Earth Work : |
| 2 | Clearing jungle including uprooting of rank vegetation, grass, brush wood, trees and saplings of girth upto 30 cm measured at a height of 1 m above ground level and removal of rubbish upto a distance of 50 m outside the periphery of the area cleared. |
| 3 | Earth work in excavation by mechanical means (Hydraulic excavator) / manual means over areas (exceeding 30cm in depth, 1.5m in width as well as 10 sqm on plan) including disposal of excavated earth, lead upto 50m and lift upto 1.5m, disposed earth to be levelled and neatly dressed.-All kinds of soil |
| 4 | Earth work in excavation by mechanical means (Hydraulic excavator) / manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan) including dressing of sides and ramming of bottoms, lift upto 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m.-All kinds of soil |
| 5 | Filling available excavated earth (excluding rock) in trenches,plinth, sides of foundations etc. in layers not exceeding 20cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift upto 1.5 m.-All kinds of soil |
| 6 | Excavating, supplying and filling of local earth (including royalty) by mechanical transport upto a lead of 5 km also including ramming and watering of the earth in layers not exceeding 20 cm in trenches, plinth, sides of foundation etc.complete. |
| 7 | Supplying and filling in plinth, under floor, foundations etc. with sand (fine) from local quarry with all lifts including spreading in horizontal layers, watering, grading to required slope, ramming, consolidating and compacting each layer by using plate compactor or by any suitable method complete. |
| 8 | Supplying chemical emulsion in sealed containers including delivery as specified.a)Chlorpyriphos/Lindane emulsifiable concentrate of 20% |
| 9 | Treatment of soil under plinth filling using chemical emulsion @ one litre per hole, 300 mm apart including drilling 12 mm diameter holes and plugging with sand filling: With Chlorpyriphos/Lindane E.C. 20% with 1% concentration |
| 10 | Diluting and injecting chemical emulsion for POST-CONSTRUCTIONAL anti-termite treatment as per IS: 6313 (Part III)- Latest revision (excluding the cost of chemical emulsion): Along external wall where the apron is not provided using chemical emulsion @ 7.5 litres/sqm of the vertical surface of the substructure to a depth of 300 mm including excavation channel along the wall & rodding etc. complete: With Chlorpyriphos/Lindane E.C. 20% with 1% concentration |
| 11 | Providing and laying in position cement concrete of specified grade excluding the cost of centring and shuttering --All work upto plinth level:a) 1:4:8 ( 1 Cement: 4 fine sand : 8 graded stone aggregate 40 mm nominal size) |
| 12 | b) 1:3:6 ( 1 Cement: 3 fine sand : 6 graded stone aggregate 40 mm nominal size) |
| 13 | Making plinth protection 50mm thick of cement concrete1:3:6 (1 cement : 3 fine sand : 6 graded well burnt brick aggregate 20 mm nominal size) over 75mm bed of dry brick ballast 40mm nominal size well rammed and consolidated and grouted with fine sand including finishing the top smooth. |
| 14 | Providing and laying in position specified grade of reinforced cement concrete excluding the cost of centring, shuttering, finishing and reinforcement- All work upto plinth level:1:1½:3 ( 1 Cement: 1½ fine sand : 3 graded stone aggregate 20 mm nominal size) |
| 15 | Reinforced cement concrete work in walls (any thickness), including attached pilasters, buttresses, plinth and skirting courses, fillets, columns, pillars, piers, abutments, posts and struts etc. upto floor five level excluding cost of centring, shuttering, finishing and reinforcement-1:1½:3 ( 1 Cement: 1½ fine sand : 3 graded stone aggregate 20 mm nominal size) |
| 16 | Reinforced cement concrete work in beams, suspended floors, roofs having slope upto 15° landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases upto floor five level excluding the cost of centring, shuttering, finishing and reinforcement-a) RCC work in suspended floors, roofs having slope upto 15° landings, balconies, shelves and chajjas.1:1½:3 ( 1 Cement: 1½ fine sand : 3 graded stone aggregate 20 mm nominal size). |
| 17 | Centering shuttering including struttings, propping etc.and removal of form work for:-Foundations, footings, bases for columns etc. for mass concrete with timber plank |
| 18 | Columns, Pillars, Piers, Abutments, Posts and Struts with shuttering ply |
| 19 | Lintels, beams, plinth beams, girders, bressumers and cantilevers with shuttering ply |
| 20 | Suspended floors, roofs, landings, balconies and access platform with shuttering ply |
| 21 | Edges of slabs and breaks in floors and walls under 20 cm. wide |
| 22 | e)Weather shade, chajjas, corbels etc. including edges |
| 23 | Reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto floor five level. Thermo-Mechanically Treated bars/ Cold twisted deformed steel bars |
| 24 | Providing precast cement concrete Jali 1:2:4 (1 cement: 2 coarse sand : 4 graded stone aggregate 6mm nominal size) reinforced with 1.6 mm dia mild steel wire including centring and shuttering, roughening cleaning, fixing and finishing in cement mortar 1:3(1cement : 3 fine sand) etc. complete, excluding the plastering of jambs, sills and soffits.a) 40 mm thick |
| 25 | First class brick work in foundation and plinth including cost of all materials as required complete:-a)In cement mortar 1:6 ( 1 cement : 6 fine sand ). |
| 26 | First class brick work in superstructure above plinth level & upto floor-five level including cost of all materials as required complete:-a)In cement mortar 1:6 ( 1 cement : 6 fine sand ). |
| 27 | Extra for brick masonry work in triangular, square and rectangular pillars including cost of all materials as required complete. |
| 28 | Half brick masonry work with first class bricks in superstructure upto floor five level including cost of all materials as required complete:-In cement mortar 1:4 ( 1 cement : 4 fine sand ). |
| 29 | Honey comb brick masonry work of half brick thickness with first class bricks in superstructure forall level including cost of all materials as required complete:-In cement mortar 1:2 ( 1 cement : 2 fine sand ). |
| 30 | Providing wood work in frames of doors, windows,clerestory windows and other frames, wrought framed and fixed in position :Local teak wood |
| 31 | Providing and fixing ISI marked flush door shutters conforming to IS: 2202 (Part I) non decorative type, core of block board construction with frame of 1st class hard wood and well matched teak 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters.a) 35 mm thick including ISI marked Stainless Steel butt hinges with necessary screws. |
| 32 | Providing 40 × 5 mm flat iron hold fast 40 cm longincluding fixing to frame with 10 mm diameter bolts,nuts and wooden plugs and embedding in cementconcrete block 30 × 10 × 15 cm 1:3:6 mix (1 cement :3 fine sand : 6 graded stone aggregate 20mmnominal size) |
| 33 | Providing and fixing factory made door frame (single rebate) made of solid PVC foam profile with homogenous fine cellular structure having smooth outer integral skin having 60mm width & 30mm thickness and shall be fixed to wall as per instructions of Engineer-In-Charge using 100x8 sheet metal CSK screws. |
| 34 | Providing and fixing 28 mm thick door shutter made of solid PVC foam profile with homogenous fine cellular structure having smooth outer integral skin having 71mm width & 28mm thick as vertical & horizontal styles. Joints are made using solvent adhesive and GI ‘C sections (39mm x 19mm x 0.6mm thick) or M S pipe (40mm x 20mm ) stiffener frame insert & telescopic polymeric ‘L’ corners .The panel shall be filled with 3mm thick high - pressure compact laminate as per manufacturer’s specifications and directions of the Engineer-in-charge, cover moulding shall be provided for covering fixing screws and elegant look.( for W.C. bathroom door shutter). |
| 35 | Providing and fixing aluminium sliding door bolts ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade with nuts and screws etc. complete :a) 300x16 mm |
| 36 | b) 250x16 mm |
| 37 | Providing and fixing aluminium tower bolts ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868 ) transparent or dyed to required colour or shade with necessary screws etc. complete :a) 300x10 mm |
| 38 | b) 150x10 mm |
| 39 | Providing and fixing aluminium handles ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade with necessary screws etc. complete :a) 125 mm |
| 40 | Providing and fixing aluminium hanging floor door stopper ISI marked anodised (anodic coating not lessthan grade AC 10 as per IS : 1868) transparent or dyed to required colour and shade with necessary screws etc. complete.a) Single rubber stopper |
| 41 | Providing and fixing expanded metal 20 x 60 mm strands 3.25 mm wide and 1.6 mm thick for windows etc. including 62 x 19 mm beading of Gamair wood. |
| 42 | Providing and fixing M.S. grills of required pattern in frames of windows etc. with M.S. flats, square or round bars etc. all complete.A) Fixed to openings /wooden frames with rawl plugs screws etc. |
| 43 | B) Fixed to steel windows by welding. |
| 44 | Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS : 1285, fixing with dash fasteners of required dia and size, including necessary filling up of gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, aluminium snap beading for glazing / paneling, C.P. brass / stainless steel screws, all complete as per architectural drawing and the direction of Engineerincharge. (Glazing and paneling and dash fasteners to be paid for separately) :-y:-Anodised aluminium (anodised transparent or dyed to required shade according to IS: 1868, Minimum anodic coating of grade AC 15). |
| 45 | B) For shutters of doors, windows & ventilators including providing and fixing hinges / pivots and making provision for fixing fittings wherever required including the cost of EPDM rubber / neoprene gasket required ( Fittings shall be paid for separately ):- Anodised aluminium (anodised transparent or dyed to required shade according to IS: 1868, Minimum anodic coating of grade AC 15). |
| 46 | Providing and fixing glazing of approved quality in aluminium doors, windows, ventilator, shutters and partition etc. with EPDM rubber / neoprene gasket etc. complete as per architectural drawing and the direction of Engineer-in-charge (Cost of snap beading shall be paid in basic item) :-A) With float glass panes of 4.0 mm thickness ( weight not less than 10.0 kg / sqm ) |
| 47 | Supplying and fixing rolling shutters of approved make, made of required size M.S. laths interlocked together through their entire length and jointed together at the end by end locks mounted on specially designed pipe shaft with brackets, side guides and arrangements for inside and outside locking with push and pull operation complete including the cost of providing and fixing necessary 275mm long wire springs grade No.2 and M.S. top cover of required thickness for rolling shutters & with handles, hold fast including embedding in cement concrete of equired grade required for fixing in position, all necessary fittings, including applying of approved steel primer etc. complete as required:- 80x1.20 mm M.S. laths with 1.20 mm thick top cover. |
| 48 | Providing and fixing M.S. fan clamp of type 1 or 16 mm MS bar bent to shape with holed ends in RCC slabs beams, during laying of steel excluding painting exposed portion of loop, all as per standard design complete. |
| 49 | Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete.a) Hot finished welded type tubes |
| 50 | Providing and fixing on wall face unplasticised Rigid PVC rain water pipes (working pressure 4 kg / cm2) conforming to IS : 13592 Type A including jointing with seal ring conforming to IS : 5382 leaving 10 mm gap for thermal expansion:a)Single socketed pipe - 110 mm OD |
| 51 | Supply & installation of pre painted Galvalume sheets (size, shape and pitch of corrugation as approved by Engineer-in-charge) in 550mpa steel grade, made out of Cold rolled steel coated with Znic-Aluminium alloy coating of 43.5% Zn, 55% Al and 1.5% Silicon confirming to ASTM A 792/A782M, ASTM A90/A90M, ASTM AS 1937, ASTM A924/A92M, Alloy coating AZ150/AZ100, colour coated with high quality polyester coating, top coated of modified polyester of 20 micron, back side coat of 5 micron, having epoxy primer coat of 5 micron on both side. Sheet should have protective guard film of 25 microns minimum to avoid scratches while transportation and should be supplied in single length upto 12 metre or as desired by Engineer-in-charge. The sheet shall be fixed using self drilling /self tapping screws of size (5.5x 55mm) with EPDM seal or with polymer coated J or L hooks, bolts and nuts 8mm diameter with bitumen and G.I. limpet washers or with G.I. limpet washers filled with white lead complete upto any pitch in horizontal/ vertical or curved surfaces excluding the cost of purlins,rafters and trusses and including cutting to size and shape wherever required. 0.50mm thickness |
| 52 | Supply & installation of pre painted Galvalume sheets roofing accessories in 550mpa steel steel grade, made out of Cold rolled steel coated with Znic-Aluminium alloy coating of 43.5% Zn, 55% Al and 1.5% Silicon confirming to ASTM A 792/A782M, ASTM A90/A90M, ASTM AS 1937, ASTM A924/A92M, Alloy coating AZ150/AZ100, colour coated with high quality polyester coating, top coated of modified polyester of 20 micron, back side coat of 5 micron, having epoxy primer coat of 5 micron on both side. Sheet should have protective guard film of 25 microns minimum to avoid scratches while transportation. Sheet should have protective guard film of 25 microns minimum to avoid scratches while transportation. The sheet shall be fixed using self drilling /self tapping screws with EPDM seal or with polymer coated J or L hooks, bolts and nuts G.I. seam bolts and nuts, G.I. plain and bitumen wishers complete for Ridges/Valley/Gutter/Flashing of width 610mm: 0.50mm thickness |
| 53 | Providing and fixing 1st class quality ceramic glazed wall tiles conforming to IS : 15622 - 2017 (thickness to be specified by the manufacturer) of approved make in all colours, shades of any size as approved by Engineer-incharge in skirting, risers of steps and dados, laid over 12 mm thick bed of cement mortar 1 : 3 (1 cement : 3 fine sand) jointed with ordinary cement slurry including pointing with white cement mixed with pigment of matching shade etc. all complete as per direction of the Engineer in-charge. 450 mm X 300 mm in all shades and design |
| 54 | Providing and laying 1st class quality ceramic floor tiles in different sizes (thickness to be specified by themanufacturer) of 1st quality conforming to IS : 15622 - 2017 of approved make in colours such as White, Ivory, Grey, Fume Red Brown, laid over 20 mm thick cement mortar 1:4 (1 cement : 4 fine sand), Jointing with grey cement slurry @ 3.3 kg/sqm including pointing the joints with white cement and matching pigment etc. all complete as per direction of the Engineer in-charge.Mat Finish Tiles/ Anti-skid Tiles/ Glossy Tiles |
| 55 | Providing and fitting fixing of PVC sheet in floor with adhesive and wall with necessary screwsas per direction of Engg-in-Charge. 2.75mm thick for wall |
| 56 | 4.75mm thick for floor |
| 57 | Providing and laying cement concrete 1:2:4 (1 cement : 2 fine sand : 4 graded well burnt brick aggregate) flooring finished with a floating coat of neat cement including cement slurry, rounding of edges and strips etc. all complete as per direction of Engineer-in-charge. 25 mm thick with 12.5 mm well burnt brick aggregate |
| 58 | Providing and fixing chequared terrazo tiles 22 mm thick with graded marble chips of size upto 6 mm, laid in floors, andings, on 20 mm thick bed of cement mortar 1 : 4 ( 1 cement : 4 fine sand ) jointed with neat cement slurry mixed with pigment to match the shade of tiles including rubbing and polishing etc. all complete as per direction of Engineer-in-charge. In light shade using white cement |
| 59 | 6 mm cement plaster of mixIn cement mortar 1:3 ( 1 cement : 3 fine sand ). |
| 60 | 12 mm cement plaster of mixIn cement mortar 1:6 ( 1 cement : 6 fine sand ). |
| 61 | 12 mm cement plaster of mixIn cement mortar 1:4 ( 1 cement : 4 fine sand ). |
| 62 | 15 mm cement plaster on the rough side of single or half brick wall of mix:In cement mortar 1:6 ( 1 cement :6 fine sand ). |
| 63 | 15 mm cement plaster on the rough side of single or half brick wall of mix:In cement mortar 1:4 ( 1 cement : 4 fine sand ). |
| 64 | Neat cement punning. |
| 65 | Applying one coat of water thinnable cement primer of approved brand and manufacturer on wall surface complete.- Water thinnable cement primer |
| 66 | Distempering with 1st quality acrylic distemper (ready mixed) having VOC content less than 50 grams/ litre, of approved brand and manufacture to give an even shade [Payment shall be made after submission of TestCertificate issued by the Manufacturer] :New work ( two or more coats) over and including water thinnable priming coat with cement primer. |
| 67 | Finishing walls with acrylic smooth exterior paint of required shade of approved brand and manufacture on new work ( two or more coats applied @ 1.67 kg/10 sqm) over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm complete(payment shall be made after submission of test certificate issued by manufacturer).New work ( two or more coats applied @ 1.67 litre/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm) |
| 68 | Applying priming coat:(Payment shall be made after submission of test certificate issued by the manufacturer)With ready mixed pink primer of approved brand and manufacture on wood work ( hard & soft wood ). |
| 69 | Applying priming coat [Payment shall be made after submission of Test Certificate issued by the Manufacturer] : With ready mixed red oxide zinc chromate primer of approved brand and manufacture on steel galvanised iron/steel works. |
| 70 | Painting with synthetic enamel paint of approved brand and manufacture of required colour to give an evenshade [Payment shall be made after submission of Test Certificate issued by the Manufacturer]:Two or more coats on new work over an under coat of suitable shade with ordinary paint (primer) of approved brand and manufacture |
| 71 | Providing and fixing G.I. pipes of medim class as per IS : 1239 with latest amendment complete with G.I.fittings and clamps, including cutting and making good the walls etc. complete as per CPWD specification and direction of the Engineer - in - charge.Internal work - Exposed on wall. |
| 72 | Providing and fixing G.I pipes of medim class as per IS : 1239 with latest amendment complete with G.I.fittings and clamps, including making good the walls/floor etc. concealed pipe including paintingtwo coats or more with anticorrosive bitumastic paint, cutting chases and making good the samecomplete as per CPWD specification and direction of the Engineer - in - charge a)15 mm nominal bore |
| 73 | b)20 mm nominal bore |
| 74 | Making chases upto 7.5x7.5 cm in walls including making good and finishing with matching surface after housing G.I. pipe etc. |
| 75 | Providing and fixing G.I. Union in G.I. pipe including cutting and threading the pipe and making long screws etc. complete (New work) a)20 mm nominal bore |
| 76 | Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end):a)32 mm nominal bore |
| 77 | Providing and fixing gun metal non-return valve of approved quality (screwed end):a)32 mm nominal bore- Vertical |
| 78 | Providing and fixing ball valve (brass) of approved quality High or low pressure, with plastic floats complete :a)25 mm nominal bore |
| 79 | Providing and fixing uplasticised PVC connection pipe with brass unions :a)45 cm lengthi) 15 mm nominal bore |
| 80 | Providing and fixing C.P. brass long body bib cock of approved quality conforming to IS standards and weighing not less than 690 gms.i) 15 mm nominal bore |
| 81 | Providing and fixing PTMT grating of approved quality and colour.A)Circular type.i) 100 mm nominal dia. |
| 82 | Cutting holes upto 30x30 cm in walls including making good the same :i) With 1st class bricks. |
| 83 | Cutting holes upto 15x15 cm in R.C.C. floors and roofs for passing drain pipe etc. and repairing the hole after insertion of drain pipe etc. with cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) including finishing complete so as to make it leak proof. |
| 84 | Providing and fixing C.P. brass stop cock (concealed) of standard design and of approved make conforming to IS:8931.A) 15 mm nominal bore |
| 85 | Providing and fixing PTMT soap Dish Holder having length of 138mm, breadth 102mm, height of 75mm with concealed fitting arrangements weighing not less than 106 gms. |
| 86 | Providing and placing on terrace (at all floor levels) polyethylene water storage tank ISI : 12701 marked with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank. |
| 87 | Providing and fixing white vitreous china pedestal type water closet (European type) with seat and lid, 10 litre low level white vitreous china flushing cistern & C.P. flush bend with fittings & C.I.brackets, 40mm flush bend, overflow arrangement with specials of standard make and mosquito proof coupling of approved municipal design complete including painting of fittings and brackets, cutting and making good the walls and floors wherever required :a) W.C. pan with ISI marked white solid plastic seat and lid. |
| 88 | Providing and fixing water closet squatting pan (Indian type W.C. pan ) with 100mm sand castIron P or S trap, 10 litre low level white P.V.C. flushing cistern with manually controlled device(handle lever) conforming to IS : 7231, with all fittings and fixtures complete including cuttingand making good the walls and floors wherever required :White Vitreous china Orrisa pattern W.C. pan of size 580x440 mm with integral type foot rests |
| 89 | Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps,32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require :a)White Vitreous China Wash basin size 630x450 mm with a pair of 15 mm C.P. brass pillar taps |
| 90 | Providing and fixing white vitreous china pedestal for wash basin completely recessed at the back for the reception of pipes and fittings. |
| 91 | Providing and fixing P.V.C. waste pipe for sink or wash basin including P.V.C. waste fittings complete.A)Flexible pipei)32 mm dia |
| 92 | Providing and fixing toilet paper holder :A)Vitreous china |
| 93 | Providing and fixing mirror of superior glass (of approved quality) and of required shape and size with plastic moulded frame of approved make and shade with 6 mm thick hard board backing :a) Rectangular shape 1500x450 mm |
| 94 | Providing and fixing 600x120x5mm glass shelf with edges round of supported on anodised aluminium angle frame with C.P. brass brackets and guard rail complete fixed with 40 mm long screws, rawl plugs etc., complete. |
| 95 | Providing and fixing PTMT towel rail complete with brackets fixed to wooden cleats with CP brass screws with concealed fitting arrangement of approved quality and colour.A) 600mm long towel rail with total length of 645mm, width 78mm and effective height of 88mm, weighing not less than 190gms. |
| 96 | Providing and fixing on wall face unplasticised Rigid PVC rain water pipes (working pressure 6 kg / cm2) conforming to IS : 13592 Type A including jointing with seal ring conforming to IS : 5382 leaving 10 mm gap for thermal expansion:a) Single socketed pipe - 110 mm OD |
| 97 | Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A including jointing with seal ring conforming to IS : 5382 leaving 10 mm gap for thermal expansion: Coupler A) i) 110 mm OD |
| 98 | B) Single equal tee without doori)110x110x110mm |
| 99 | C) Single equal tee with doori)110x110x110mm |
| 100 | D) Bend 87.5°i)110mm |
| 101 | E) Pain shoei)110mm |
| 102 | Providing and fixing unplasticised -PVC pipe clips of approved design to unplasticised - PVC pipes by means of 50x50x50mm hard wood plugs, screwed with M.S. screws of required length including cutting brick work and fixing with cement mortar 1 : 4 (1cement : 4 fine sand) making good the wall etc. complete.a)110mm |
| 103 | Providing and fixing to the inlet mouth of soil, waste & vent pipes pipe PTMT grating with thickness of 8 mm and weighing not less than 100gm. complete.a)100mm Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Sep 21, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedSep 30, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 6 daysSep 30, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 6 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender