Tender For Provision For Ticketing Related Infrastructure And Public Amenities At Najaf Khan Tomb, New Delhi
Tender Value
51.11 Lakhs
Estimated cost
Bid Submission
05 Oct 2026
13 days left
EMD
1.02 Lakhs
Bank guarantee accepted
Document Fee
Ref. Documents
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Delhi → Delhi
EMD Exemption
Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for Provision For Ticketing Related Infrastructure And Public Amenities At Najaf Khan Tomb, New Delhi
BOQ
| Sl. No. | Item Description |
| 1 | Earth work in excavation by mechanical means (Hydraulic excavator)/ manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, lift upto 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m. [ All kinds of soil ] |
| 2 | Demolishing cement concrete manually/ by mechanical means including disposal of material within 50 metres lead as per direction of Engineer - in - charge. Nominal concrete 1:3:6 or richer mix (i/c equivalent design mix). |
| 3 | Demolishing brick work manually/ by mechanical means including stacking of serviceable material and disposal of unserviceable material within 50 metres lead as per direction of Engineer-in-charge. In Cement Mortar. |
| 4 | Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level : 1:4:8 (1 Cement : 4 coarse sand (zone-III) derived from natural sources : 8 graded stone aggregate 40 mm nominal size derived from natural sources). |
| 5 | Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in foundation and plinth in: Cement mortar 1 :4 (1 cement : 4 coarse sand) |
| 6 | Dismantling stone slab flooring laid in cement mortar including stacking of serviceable material and disposal of unserviceable material within 50 metres lead. |
| 7 | Dismantling roofing including ridges, hips, valleys and gutters etc., and stacking the material within 50 metres lead of: - Asbestos Cement sheet |
| 8 | Pointing of joints in Lakhori brick masonry using lime-surkhi mortar in the proportion of 1:1:1 (1 part lime: 1 part surkhi: 1 part coarse sand), admixed with traditional additives such as belgiri, gur, gum, and sunn, including raking out of joints, thorough cleaning and washing, and finishing complete, along with carriage of all materials and water within a lead of 50 to 200 meters and lift up to 10 meters. |
| 9 | Recess pointing of R.R. stone masonry in lime surkhi mortar 1:1:1 (1 Lime, 1 Surkhi, 1 C. sand) with adhesive materials such as belgiri, molasses, gum, & san including, racking out the joints, cleaning & washing the joints including carriage of water & material within a lead upto 100 M & left upto 4.00 M approx . |
| 10 | Dismantling wood work in frames, trusses, purlins and rafters up to 10 metres span and 5 metres height including stacking the material within 50 metres lead : - Of sectional area below 40 square centimetres |
| 11 | Dismantling old damaged / pulverized lime plaster 40 to 50 mm or skirting raking out joints and cleaning the surface for plaster including disposal of rubbish to the dumping ground within 100 metres lead. |
| 12 | Providing and laying 40 mm to 50 mm avg. thick lime plaster on curved and tapered wall surface in the Arch curves & nitches on the walls in three coats in lime mortar 1:1:1 (1 lime, 1 C.Sand, 1 Surkhi) including supply of water and materials with in a lead up to 100 mtr and lift up to 5 mtr. |
| 13 | Provision for providing and fixing Red Sand stone working in string coarse as Dab, Quid, column, Choukhat, Steps in composite lime mortar 1:1:1 (1 Lime, 1 Surkhi, 1 C.Sand) with composite materials including taking out decayed red stone members bit by bit without disturbing to the adjoining structures and including pointing with composite lime mortar with an admixture of pigment matching to the stone shades. |
| 14 | R.R.stone masonry in Lime surkhi mortar 1:1:1 (1 Lime, 1 Surkhi, 1 C. sand) mixed with adhesive materials such as Gur, Belgiri & Gum including carriage of Water and Materials within a lead upto 100 M & left upto 4.00 M approx. |
| 15 | CEMENT PLASTER WITH A FLOATING COAT OFNEAT CEMENT 15 mm cement plaster on rough side of single or half brick wall finished with a floating coat of neat cement of mix : - (1 cement: 3 fine sand) |
| 16 | Stone work (machine cut edges) for wall lining etc. (veneer work) upto 10 metre height, backing filled with a grout of average 12 mm thick cement mortar 1 :3 (1 cement : 3 coarse sand) including pointing in white cement mortar 1 :2 (1 white cement : 2 stone dust) with an admixture of pigment matching the stone shade : (To be secured to the backing and the sides by means of cramps and pins which shall be paid for separately) :8.14.1 Red sand stone - exposed face fine dressed with rough backing. [ 40 mm thick ] |
| 17 | 40 mm thick fine dressed stone flooring over 20 mm (average) thick base of cement mortar 1 :5 (1 cement : 5 coarse sand), including pointing with cement mortar 1 :2 (1 cement: 2 stone dust) with an admixture of pigment to match the shade of stone.[ Red sand stone] |
| 18 | Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS: 15622, of approved make, in all colours and shades, laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joints with white cement and matching pigments etc. complete. [ Size of Tile 600x600 mm.] |
| 19 | Demolishing stone rubble masonry manually/ by mechanical means including stacking of serviceable material and disposal of unserviceable material within 50 metres lead as per direction of Engineer-in-charge : |
| 20 | Providing and laying gang saw cut 18 mm thick, mirror polished pre moulded and pre polished machine cut granite stone of required size and shape of approved shade, colour and texture in footpath, flooring cut granite stone of required size and shape of approved shade, colour and texture in footpath, flooring in road side plazas and similar locations, laid over 20mm thick base of cement mortar 1:4 (1cement : 4 coarse sand) including grouting the joints with white cement mixed with matching pigment, epoxy touch ups etc. complete as per direction of Engineer-in-Charge. [ With granite stone of area less than 0.50 sqm.] |
| 21 | Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS: 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm, including pointing in white cement mixed with pigment of matching shade complete. |
| 22 | Providing edge moulding to 18 mm thick marble stone counters, Vanities etc., including machine polishing to edge to give high gloss finish etc. complete as per design approved by Engineer-in-Charge. [ Granite work ] |
| 23 | Providing corrugated G.S. sheet roofing including vertical/ curved surface fixed with polymer coated J or L hooks, bolts and nuts 8 mm diameter with bitumen and G.I. limpet washers or with G.I. limpet washers filled with white lead, including a coat of approved steel primer and two coats of approved paint on overlapping of sheets complete (up to any pitch in horizontal/ vertical or curved surfaces), excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required. 12.1.1 1.00 mm thick with zinc coating not less than 275 gm/m2 |
| 24 | Steel work welded in built up sections/ framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required. 10.25.2 In gratings, frames, guard bar, ladder, railings, brackets, gates and similar works. |
| 25 | Extra for circular cutting in C.G.S. sheet roofing for making opening of area exceeding 40 sq. decimeter: 12.3.1 1.00 mm thick |
| 26 | Supply of Cast Iron Benches with Arm Rest having 3 seater seating capacity of size approximately 1620 x 620 x 740mm weight approx. 85 Kg. (+-5%) grated with MS Iron rectagonal pipe of size 7 cm. x 3cm. x 2mm thick. 11 nos. horizontal post painting with required colour and placing them as per the instructions of site incharge. |
| 27 | \\"Providing, Supplying, Transporting, Loading, Unloading, Fixing and Commissioning of Porta Cabin/Guard Cabin of size 6'-0\\" × 4'-0\\" × 8'-6\\" fabricated with heavy-duty MS frame, heavy MS sheet walls and roof, complete with 25 mm thick waterproof plywood flooring fixed on MS frame, vinyl wall-to-wall floor covering, complete glass wool insulation in walls and roof for thermal and sound insulation, one glazed window with security grills, suitable entrance door with four heavy-duty locking arrangements and lifting hooks/provisions attached to pillars for loading and unloading, complete internal electrification with branded fittings including LED tube light, switch, socket, wiring, MCB box and all accessories, one seating arrangement for security guard, painting and finishing, including all materials, labour, tools and tackles, transportation to Najaf Khan Tomb, site, Hydra/crane charges for loading and unloading, installation, leveling of ground, preparation of hard surface/base, positioning, fixing and making the cabin ready for use as per the direction of Engineer-in-Charge, complete in all respects. \\" |
| 28 | Provision for providing and fixing of plumbing items, Sanitary Work and water supply work required at site.Providing and fixing facatory made stainless steel (Grade 304) grab bars/ han rails for accessible toilet including vertical grab bars, folding support rails, fixing plates, anchror fasteners, welding, polishing and all accessories complete as per approved desing and direction of Engineer - in-charge. Vertical grab bar 750mm (SS 304) including fixing plates, anchor bolts accessories |
| 29 | Folding support rail 850 mm including fixing plates, anchor bolts accessories. |
| 30 | \\"Providing and fixing CP Brass 32mm size Bottle Trap of approved quality & make and as per the direction of Engineer-in-charge. |
| 31 | Providing and fixing vitreous china urinal partition plate (White colour), of approved brand parryware or equivalent complete with C.I/M.S brackets, bolts, nuts and all necessary fittings as required. |
| 32 | Providing and fixing 32 mm dia CP brass urinal waste coupling with CP brass P trap and connection pipe complete |
| 33 | . Providing and fixing 8 mm dia C.P. / S.S. Jet with flexible tube up to 1 metre long with S.S. triangular plate to Eureopean type W.C. of quality and make as approved by Engineer - in - charge. (DSR 2023 code no.- 17.16A) |
| 34 | Providing and fixing P.V.C. waste pipe for sink or wash basin including P.V.C. waste fittings complete. Flexible pipe 40 mm dia (DSR 2023 code no.- 17.28.2.2) |
| 35 | Providing and fixing 600x450 mm beveled edge mirror of superior glass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete. (DSR 2023 code no.- 17.31) |
| 36 | Providing and fixing toilet paper holder : C.P. brass (DSR 2023 code no.- 17.34.1) |
| 37 | Polyethylene water storage tank with cover and suitable locking arrangement.(DSR 2023 code no.-1649) |
| 38 | \\"Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings and fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge. Concealed work, including cutting chases and making good the walls etc.(DSR 2023 code no.- 18.8.1) |
| 39 | Providing and fixing single lever extended height (tall bod) basin mixer of approved brand cera, parryware or equivalent, chrome plated brass body with connection pipes and all accessories complete. |
| 40 | \\"Providing and fixing C.P. brass long body bib cock of approved quality conforming to IS standards and weighing not less than 690 gms. 15 mm nominal bore (DSR 2023 code no.- 18.51.1) |
| 41 | Providing and fixing white vitreous china pedestal type water closet (European type) with seat and lid, 10 litre low level white vitreous china flushing cistern & C.P. flush bend with fittings & C.I. brackets, 40 mm flush bend, overflow arrangement with specials of standard make and mosquito proof coupling of approved municipal design complete, including painting of fittings and brackets, cutting and making good the walls and floors 17.3.1 W.C. pan with ISI marked white solid plastic seat and lid |
| 42 | Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require: White Vitreous China Wash basin size 630x450 mm with a single 15 mm C.P. brass pillar tap |
| 43 | Jalli Small Size |
| 44 | Elbow |
| 45 | T- Joint |
| 46 | Angle Valve cock |
| 47 | CPVC Solvent Cement (500ml) |
| 48 | CPVC Union |
| 49 | Connection Nipple |
| 50 | Providing and fixing Stainless Steel A ISI 304 (18/8) kitchen sink as per IS:13983 with C.I. brackets and stainless steel plug 40 mm, including painting of fittings and brackets, cutting and making good the walls wherever required :17.10.2 Kitchen sink without drain board 17.10.2.2 610x460 mm bowl depth 200 mm |
| 51 | Labour charges for fixing of plumbing items, sanitary work etc. |
| 52 | Transportation charges of material from market to site |
| 53 | Provision for providing and fixing of electrical items required at site.PVC insulated 6 mm single core flexible copper wires & cables polycab/Crompton/havells (1 bundle= 90 rmt ) |
| 54 | PVC insulated 2.5 mm single core flexible copper wires & cables polycab/Crompton/havells (1 bundle= 90 rmt ) |
| 55 | PVC insulated 1.5 mm single core flexible copper wires and cables polycab/crompton/havells (1 bundle= 90 rmt ) |
| 56 | PVC insulated 1 mm single core flexible copper wires & cables polycab/crompton/havells (1 bundle. = 90 rmt ) |
| 57 | LED Bulb 15 watt (Havells/Orient or equivalent) |
| 58 | Havells or equivalent Ventil Air DX 200 mm exhaust fan (white) |
| 59 | Pedestal fan High Speed (Havells or equivalent) |
| 60 | Wall fan (Havells or equivalent) |
| 61 | Electric Tape box (Steelgrip or equivalent ) |
| 62 | LED Tube lights 20 watt (Havells/Crompton or equivalent) |
| 63 | MCCB 32 Amp (4 pole) of approved brand |
| 64 | MCB 100 Amp 4 Pole of approved brand |
| 65 | MCB 63 Amp. of approved brand |
| 66 | Copper Busbars of required dimensions |
| 67 | Busbars insulator |
| 68 | Indicator |
| 69 | MCB electricity panel/ feeder box of size 3ft. x 4ft. Mild Steel (MS) structure with a powder-coated, rust-proof finish and double doors with pillars etc.complete |
| 70 | MCB panel box of size 1ft. x 1.5 ft. |
| 71 | 32A single pole MCB of approved brand (Havells or equivalent) |
| 72 | 16A single pole MCB of approved brand (Havells or equivalent) |
| 73 | 32 amp double pole mcb of approved brand (Havells or equivalent) |
| 74 | Havells or equivalent 6A one way switch |
| 75 | Havells or equivalent 6A five pin socket |
| 76 | Havells or equivalent 6A -16A three pin combined shutter socket |
| 77 | Extension board of approved brand |
| 78 | Havells or equivalent 16 A one way switch with indicator |
| 79 | 4 Core x 25 sq.mm aluminium armoured cable of approved brand like Havells, Polycab or equivalent from main panel to booking counter |
| 80 | Luminous Inverter & Battery Combo for Booking Office – Icon 1600 (1400VA/12V) Sine Wave Inverter with Ultra Charge 250Ah Tall Tubular Inverter Battery. |
| 81 | Labour charges for fixing all electrical items (electrician + helper) complete job work |
| 82 | Transportation charges of material from market to site |
| 83 | Providing, supplying and fixing/placing approved quality furniture and fixtures for Baby Care Room at Najaf Khan Tomb including nursing chair, baby changing unit, storage cabinet, side table and allied accessories, complete in all respects as per approved design and direction of Engineer-in-Charge.Providing and placing Baby Changing Table/counter of standard size made of moisture-resistant board with laminate finish with rounded edges, storage shelves and protective safety rail, baby changing mattress with waterproof cover etc complete |
| 84 | Providing and fixing Nursing Chair/Feeding Chair with cushioned seat and backrest of approved make, complete. |
| 85 | Providing and placing pedal operated Stainless Steel Dustbin of suitable capacity, complete |
| 86 | Providing and supplying Storage Cabinet made of pre-laminated particle board/HDHMR board with shutters, shelves and fittings, complete. |
| 87 | P/F Wall mirror |
| 88 | Providing and fixing false ceiling at all heights including providing and fixing of frame work made of special sections, power pressed from M.S. sheets and galvanized with zinc coating of 120 gms/sqm (both side inclusive) as per IS : 277 and consisting of angle cleats of size 25 mm wide x 1.6 mm thick with flanges of 27 mm and 37mm, at 1200 mm centre to centre, one flange fixed to the ceiling with dash fastener 12.5 mm dia x 50 mm long with 6 mm dia bolts, other flange of cleat fixed to the angle hangers of 25x1 0x0.50 mm of required length with nuts & bolts of required size and other end of angle hanger fixed with intermediate G.I. channels 45x15x0.9 mm running at the spacing of 1200 mm centre to centre, to which the ceiling section 0.5 mm thick bottom wedge of 80 mm with tapered flanges of 26 mm each having lips of 10.5 mm, at 450 mm centre to centre, shall be fixed in a direction perpendicular to G.I. intermediate channel with connecting clips made out of2.64 mm dia x 230 mm long G.I. wire at every junction, including fixing perimeter channels 0.5 mm thick 27 mm high having flanges of 20 mm and 30 mm long, the perimeter of ceiling fixed to wall/partition with the help of rawl plugs at 450 mm centre, with 25 mm long dry wall screws@ 230 mm interval, including fixing of gypsum board to ceiling section and perimeter channel with the help of dry wall screws of size 3.5 x 25 mm at 230 mm c/c, including jointing and finishing to a flush finish of tapered and square edges of the board with recommended jointing compound , jointing tapes , finishing with jointing compound in 3 layers covering upto 150 mm on both sides of joint and two coats of primer suitable for board, all as per manufacturer's specification and also including the cost of making openings for light fittings, grills, diffusers, cutouts made with frame of perimeter channels suitably fixed, all complete as per drawings, specification and direction of the Engineer in Charge but excluding the cost of painting with :12.45.4 Fully Perforated Gypsum Plaster Board of size 1200 x 2400x12.5 mm having approx. 15 % perforated area with perforation size and pattern as approved by the Engineerin- charge and as per manufacturer's specification, with all 4 sides tapered and backed by acoustical tissue with NRC value not less than 0.60 |
| 89 | Providing and laying 50 mm thick lime concrete coping top of the wall with brick aggregate10 to 20 mm thick nominal size & 50% lime surkhi mortar 1:1:1 (1 Lime , 1 Surkh , 1 C sand) with Belgiri, Gur treatment including carriage of water & materials with in a 200 m approx. |
| 90 | \\"Painting with synthetic enamel paint of approved brand and manufacture to give an even shade : Two or more coats on new work over an under coat of suitable shade with ordinary paint of approved brand and manufacture\\" |
| 91 | Providing and fixing double scaffolding system (cup lock type) on the exterior side, up to seven story height made with 40 mm dia M.S. tube 1.5 m centre to centre, horizontal & vertical tubes joining with cup & lock system with M.S. tubes, M.S. tube challies, M.S. clamps and M.S. staircase system in the scaffolding for working platform etc. and maintaining it in a serviceable condition for the required duration as approved and removing it there after. The scaffolding system shall be stiffened with bracings, runners, connection with the building etc wherever required for inspection of work at required locations with essential safety features for the workmen etc. complete as per directions and approval of Engineer in-charge. The elevational area of the scaffolding shall be measured for payment purpose. The payment will be made once irrespective of duration of scaffolding. |
| 92 | Disposal of moorum/building rubbish/ malba/ similar unserviceable, dismantled or waste material by mechanical transport including loading, transporting, unloading to approved municipal dumping ground for lead upto 10 km for all lifts, complete as per directions of Engineer-in-charge. |
| 93 | Providing, supplying, installing, testing and commissioning of RO based drinking water purification plant of minimum 250 LPH capacity, suitable for public use for approximately 500 persons per day, comprising multi-grade sand filter, activated carbon filter, micron cartridge filter, high pressure pump, RO membrane assembly, UV/UF purification system, suitable control panel with electrical protections, flow meters, pressure gauges, SS-304 treated water storage tank of minimum 500 litre capacity, SS-304 drinking water dispensing arrangement with minimum 3 outlets, complete with all necessary interconnecting UPVC/CPVC/SS piping, valves, fittings, supports, drain connections, electrical wiring, earthing, installation, testing and commissioning, including transportation and all accessories, complete as directed by Engineer-in-Charge.250 LPH RO Plant [Automatic, RO + UV/UF, commercial grade, SS skid] |
| 94 | Raw water pre-treatment [ Multi-grade sand filter with FRP vessel, activated carbon filter, valves & media] |
| 95 | High pressure/feeding arrangement [Suitable pump, pressure gauges, low-pressure switch etc.] |
| 96 | 500 L SS-304 storage tank [ Food-grade SS-304, with lid, inlet, outlet, drain & float arrangement] |
| 97 | UV/UF post-treatment [ UV sterilizer/UF assembly suitable for 250 LPH] |
| 98 | SS drinking-water dispensing unit [ SS-304, minimum 3 outlets/taps with suitable fittings ] |
| 99 | Interconnecting piping [ Food-grade UPVC/CPVC/SS piping, valves, unions, elbows, tees etc.] |
| 100 | Electrical installation [ Cable, MCB, isolator, starter/control wiring, earthing etc.] |
| 101 | Installation & commissioning [ Complete installation, testing, trial run and commissioning ] |
| 102 | Transportation & handling [ Transportation to site, unloading and shifting] |
| 103 | Water quality testing [ Raw and treated water testing through approved laboratory] |
| 104 | Providing and fixing stainless steel (SS 304 grade) signages board of required sizes, duly fabricated with 1.5mm thickness, having digitally printed / vinyl cut Hindi and English text as required, including fixing accessories, SS screws/fasteners, and all necessary fittings, complete as per the design, colour, size and direction of Engineer- in-Charge.signages board of size 9\\" x 12 \\" required for booking counter. |
| 105 | signages board of size 9\\" x 12 \\" of entry and exit gate |
| 106 | signages board of size 18\\"x 24\\" for displaying rates of ticket for visitors |
| 107 | signages board of size 9\\" x 12 \\" required for Baby feeding room |
| 108 | signages board of size 9\\" x 12 \\" required for Interpretation centre |
| 109 | signages board of size 9\\" x 12 \\" required for clock room |
| 110 | Providing and fixing of notice board describing the details of prohibited articles not allowed inside Najaf Khan Tomb, made with 40×40×2 mm angle at base and 50×20 mm hollow pipe at top, having 4 mm thick ACP sheet of size 4 ft × 6 ft with vinyl printing, including cartridge charges and all allied works complete as per direction of Engineer -in- charge. |
| 111 | Providing and fixing of information board describing details of Najaf Khan Tomb Booking Counter, made with 40×40×2 mm angle frame, having 4 mm thick ACP sheet of size 3 ft × 6 ft with vinyl printing, including cartridge charges and all allied works complete as per direction of Engineer - in -charge. |
| 112 | Providing and laying 75 mm thick compacted bed of dry brickaggregate of 40 mm thick nominal size including spreading,well ramming, consolidating and grouting with jamuna sand,including finishing smooth etc. complete as per direction of Engineer-in- charge. |
| 113 | Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift upto 1.5 m. |
| 114 | Reinforced cement concrete work in beams, suspended floors, roofs having slope up to 15° landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases above plinth level up to floor five level, excluding the cost of centering, shuttering, finishing and reinforcement with 1:1.5:3 (1 cement : 1.5 coarse sand(zone-III) derived from natural sources : 3 graded stone aggregate 20 mm nominal size derived from natural sources). |
| 115 | Centering and shuttering including strutting, propping etc. and removal of form for Shelves (Cast in situ) |
| 116 | Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete above plinth level. Mild steel and Medium Tensile steel bars |
| 117 | Providing, supplying, installing, testing and commissioning of SS-304 water chiller suitable for cooling purified RO drinking water, having minimum water chilling capacity of 250 LPH, with minimum 80 litre insulated storage capacity, hermetically sealed energy-efficient compressor, eco-friendly refrigerant, automatic temperature control/thermostat, SS-304 food-grade water tank and internal components in contact with water, suitable condenser, evaporator coil, temperature indicator, drain arrangement, SS-304 drinking water outlets, necessary inlet/outlet connections, insulation, electrical control panel with MCB/overload protection, connecting piping, valves and fittings, complete with transportation, unloading, installation, testing and commissioning, including all materials, labour, tools and accessories, complete as directed by Engineer-in-Charge250 LPH SS water chiller with 80-L storage [EACH] |
| 118 | SS dispensing arrangement [EACH] |
| 119 | Piping, valves & fittings [EACH] |
| 120 | Electrical/control arrangement [EACH] |
| 121 | Installation, testing & commissioning [EACH] |
| 122 | Transportation/handling [EACH] |
| 123 | Providing and fixing of Red Sand stone pillar for bollard light of size 0.1 x 0.1 m and height of 0.90 m with making hole for fixing of LED light including cutting of shape as per design, fixing of light, connections, wire, labour and transportation charges all complete. |
| 124 | Providing, supplying, installing, testing and commissioning of interactive digital information kiosk for public use, comprising robust MS/SS powder-coated kiosk enclosure suitable for indoor/outdoor installation, minimum 43\\"/55\\" commercial-grade LED/LCD touchscreen display, industrial/mini PC with suitable processor, minimum 8 GB RAM and 256 GB SSD, Wi-Fi/LAN connectivity, speakers, stereo headphone facility with headphone jack and volume control, USB ports, microphone, webcam where required, media player, UPS/power backup, necessary electrical wiring, MCB/SMPS, cooling/ventilation arrangement, keyboard/mouse, kiosk management software and required operating system. The kiosk shall be capable of displaying text, photographs, maps, videos, audio guides and other digital information and shall have touch-based navigation. Item shall include complete fabrication, graphics/signage, transportation, installation, testing, commissioning and integration of all hardware/software, including all accessories and consumables necessary for satisfactory operation, complete as directed by Engineer-in-Charge |
| 125 | Repairing and restoration of existing pole light, including checking and rectification of existing electrical wiring, replacement of damaged/defective wires, cables, holders, connectors, terminals, glands, junction boxes and other necessary electrical accessories; providing electrical connection from existing main electrical panel to the existing pole light by excavation of trench in ordinary soil, laying of suitable heavy-duty PVC/HDPE/GI protective pipe/conduit, drawing/laying of suitable size copper/aluminium armoured cable, including cable joints and termination with suitable glands and lugs; backfilling and compaction of excavated trench; providing necessary bends, couplers, clamps, saddles and accessories; testing of insulation resistance, continuity and polarity; replacement of damaged light fitting/LED lamp/driver and other defective components wherever required; reconnecting and testing the existing pole light and making it fully operational, complete in all respects as directed by Engineer-in-Charge |
| 126 | Dismantling aluminium/ Gypsum partitions, doors, windows, fixed glazing and false ceiling including disposal of unserviceable material and stacking of serviceable material with in 50 meters lead as directed by Engineer-in-charge. |
| 127 | Provision for repair of existing damaged red sand stone benches to be fixed at different locations in the premises of Najaf KhanTomb including fixing with adhesive material and labour charges etc. complete. |
| 128 | Providing, fabricating and fixing decorative laser-cut mild steel sheet jali of approved design/pattern, fabricated from 3 mm thick M.S. sheet, including preparation of CAD/CAM drawing, CNC/laser cutting, cutting of sheet to required size, edge grinding, welding/fixing to required M.S. frame/support, necessary cutting, wastage, handling, transportation, one coat of approved red oxide/epoxy primer and two coats of synthetic enamel paint of approved shade, complete in all respects as directed by Engineer-in-Charge. |
| 129 | Provision for Hiring of Hydra/mobile hydraulic crane of suitable capacity for shifting, loading, unloading and placing of pre-fabricated porta cabin from existing location to the designated location, including mobilization, operation of crane, operator, fuel, loading/unloading, transportation within site premises and all incidental charges, complete as directed by the Engineer-in-Charge. |
| 130 | Provision for fabricating and fixing/modifying existing M.S. entrance gate including raising the gate to the required level/height, cutting and removal of existing M.S. members wherever required, providing and fixing two numbers of pedestrian gates within the existing main gate with M.S. angle frame and intermediate members, including M.S. hinges, tower bolts, aldrops/drop bolts, locking arrangements, welding, cutting, drilling, grinding, alignment, strengthening, necessary fittings, primer and finishing coats, labour, tools and tackles, complete in all respects as directed by the Engineer-in-Charge. |
| 131 | Removing dry or oil bound distemper, water proofing cement paint and the like by scrapping, sand papering and preparing the surface smooth including necessary repairs to scratches etc. complete. |
| 132 | Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete. |
| 133 | Distempering with 1st quality acrylic distemper (ready mixed) having VOC content less than 50 gms/litre, of approved manufacturer, of required shade and colour complete, as per manufacturer's specification.New work (two or more coats) over and including water thinnable priming coat with cement primer |
| 134 | Providing and fixing 12mm thick frameless toughened glass door shutter of approved brand and manufacture, including providing and fixing top & bottom pivot & double acting hydraulic floor spring type fixing arrangement and making necessary holes etc. for fixing required door fittings, all complete as per direction of Engineer in charge (Door handle, lock and stopper etc. to be paid separately) |
| 135 | Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / paneling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing, paneling and dash fasteners to be paid for separately) : 21.1.1 For fixed portion 21.1.1.2 Powder coated aluminium (minimum thickness of powder coating 50 micron) |
| 136 | Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / paneling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing, paneling and dash fasteners to be paid for separately) : 21.1.2 For shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber / neoprene gasket required (Fittings shall be paid for separately)21.1.2.2 Powder coated aluminium (minimum thicknessof powder coating 50 micron) |
| 137 | Providing and fixing ISI marked aluminium butt hinges anodised (anodic coating not less than grade AC 10 as per IS: 1868) transparent or dyed to required colour or shade with necessary screws etc. complete: 9.95.1 125x75x4 mm |
| 138 | Providing & fixing aluminium sliding door bolt, ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868), transparent or dyed to required colour or shade, with nuts and screws etc. complete : 9.96.2 250x16 mm |
| 139 | Providing and fixing aluminium handles, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS: 1868) transparent or dyed to required colour or shade, with necessary screws etc. complete : 9.100.1 125 mm Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Sep 21, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedOct 05, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 13 daysOct 06, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 14 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender