Tender For Renovation And Upgradation Of Existing Pavilion At Sports Complex, Sector 7, Chandigarh.(Composite Work)
Tender Value
49.32 Lakhs
Estimated cost
Bid Submission
28 Sep 2026
6 days left
EMD
98645
Bank guarantee accepted
Document Fee
Ref. Documents
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Chandigarh → Chandigarh
EMD Exemption
Not Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for Renovation And Upgradation Of Existing Pavilion At Sports Complex, Sector 7, Chandigarh.(Composite Work)
BOQ
| Sl. No. | Item Description |
| 1 | CIVIL WORK: Earth work in excavation by mechanical means (Hydraulic excavator) / manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, for all lift, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m. : All kinds of soil. |
| 2 | Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 and for all lift. |
| 3 | Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level: 1:5:10 (1 cement: 5 coarse sand (zone-Ill) derived from natural sources : 10 graded stone aggregate 40 mm nominal size derived from natural sources) |
| 4 | Providing and laying in position ready mixed or site batched design mix cement concrete for reinforced cement concrete work; using coarse aggregate and fine aggregate derived from natural sources, Portland Pozzolana / Ordinary Portland /Portland Slag cement, admixtures in recommended proportions as per IS: 9103 to accelerate I retard setting of concrete, to improve durability and workability without impairing strength; including pumping of concrete to site of laying, curing, carriage for all leads; but excluding the cost of centering, shuttering, finishing and reinforcement as per direction of the engineer-in-charge, for the following grades of concrete.: Note: Extra cement up to 10% of the minimum specified cement content in design mix shall be payable separately. In case the cement content in design mix is more than 110% of the specified minimum cement content, the contractor shall have discretion to either re-design the mix or bear the cost of extra cement. : All works upto plinth level : Concrete of M25 grade with minimum cement content of 330 kg /cum |
| 5 | Centering and shuttering including strutting, propping etc. and removal of form for : Lintels, beams, plinth beams, girders, bressumers and cantilevers |
| 6 | Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto plinth level. : Thermo-Mechanically Treated bars of grade Fe-500D or more. |
| 7 | Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in foundation and plinth in: Cement mortar 1 :4 (1 cement : 4 coarse sand) |
| 8 | Half brick masonry with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor Vlevel. : Cement mortar 1 :3 (1 cement :3 coarse sand) |
| 9 | Mirror polishing on marble work/Granite work/stone work where ever required to give high gloss finish complete. |
| 10 | Providing and fixing ISI marked flush door shutters conforming to IS :2202 (Part I) non-decorative type, core of block board construction with frame of 1st class hard wood and well matched commercial 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters: 35 mm thick excluding ISI marked Stainless Steel butt hinges with necessary screws. |
| 11 | Extra for providing lipping with 2nd class teak wood battens 25 mm minimum depth on all edges of flush door shutters (over all area of door shutter to be measured). |
| 12 | Providing and fixing aluminium sliding door bolts, ISI marked anodised anodic coating not less than grade AC 10 as per IS : 1868), transparent or dyed to required colour or shade, with nuts and screws etc. complete : 300 x 16 mm |
| 13 | Providing and fixing aluminium tower bolts, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868 ) transparent or dyed to required colour or shade, with necessary screws etc. complete: 200 x 10 mm |
| 14 | Providing and fixing aluminium handles, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade, with necessary screws etc. complete : 125 mm |
| 15 | Providing and fixing aluminium hanging floor door stopers ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour and shade with necessary screws etc. complete. : Twin Rubber Stopper (DSR-9.101.2) |
| 16 | Providing & Fixing decorative high pressure laminated sheet of plain / wood grain in gloss / matt / suede finish with high density protective surface layer and reverse side of adhesive bonding quality conforming to IS : 2046 Type S, including cost of adhesive of approved quality. : 1.0 mm thick (DSR-9.127.2) |
| 17 | Kota stone slab flooring over 20 mm (average) thick base laid over and jointed with grey cement slurry mixed with pigment to match the shade of the slab, including rubbing and polishing complete with base of cement mortar 1 : 4 (1 cement : 4 coarse sand) : 25 mm thick |
| 18 | Kota stone slabs 20 mm thick in risers of steps, skirting, dado and pillars laid on 12 mm (average) thick cement mortar 1:3 (1 cement: 3 coarse sand) and jointed with grey cement slurry mixed with pigment to match the shade of the slabs, including rubbing and polishing complete. |
| 19 | Extra for pre finished nosing in treads of steps of Kota stone/ sand stone slab. |
| 20 | 12 mm cement plaster of mix : 1:4 (1 cement: 4 fine sand) |
| 21 | 15 mm cement plaster on the rough side of single or half brick wall of mix : 1:4 (1 cement: 4 fine sand) |
| 22 | Distempering with oil bound washable distemper of approved brand and manufacture to give an even shade : New work (two or more coats) over and including priming coat with cement primer. |
| 23 | Finishing walls with Premium Acrylic Smooth exterior paint with Silicone additives of required shade: New work (Two or more coats applied @ 1.43 ltr/10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/10 sqm) |
| 24 | Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete. |
| 25 | Distempering with 1st quality acrylic distemper (ready mixed) having VOC (Volatile Organic Compound ) content less than 50 gram/ litre, of approved brand and manufacturer including applying additional coats wherever required to achieve even shade and colour : Old work (one or more coats) |
| 26 | Removing dry or oil bound distemper, water proofing cement paint and the like by scrapping, sand papering and preparing the surface smooth including necessary repairs to scratches etc. complete |
| 27 | Finishing walls with Premium Acrylic Smooth exterior paint with Silicone additives of required shade : Old work (one or more coats applied @ 0.83 ltr/10 sqm). |
| 28 | Demolishing cement concrete manually/ by mechanical means including disposal of material within 50 metres lead as per direction of Engineer - in - charge. : Nominal concrete 1:3:6 or richer mix (including equivalent design mix) |
| 29 | Demolishing R.C.C. work manually/ by mechanical means including stacking of steel bars and disposal of unserviceable material within 50 metres lead as per direction of Engineer - in- charge. |
| 30 | Demolishing brick work manually/ by mechanical means including stacking of serviceable material and disposal of unserviceable material within 50 metres lead as per direction of Engineer-in-charge. : In cement mortar |
| 31 | Taking out doors, windows and clerestory window shutters (steel or wood) including stacking within 50 metres lead : Of area beyond 3 sq. metres |
| 32 | Dismantling stone slab flooring laid in cement mortar including stacking of serviceable material and disposal of unserviceable material within 50 metres lead. |
| 33 | Dismantling old plaster or skirting raking out joints and cleaning the surface for plaster including disposal of rubbish to the dumping ground within 50 metres lead. |
| 34 | Disposal of building rubbish / malba / similar unserviceable, dismantled or waste materials by mechanical means, including loading, transporting, unloading to approved municipal dumping ground or as approved by Engineer-in-charge, beyond 50 m initial lead, for all leads including all lifts involved. |
| 35 | Providing and laying vitrified floor tiles of specified size (thickness to be specified by the manufacturer) of 1st quality with water absorption less than 0.08% and conforming to IS : 15622, of approved make, in all colours and shades, laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand), jointing with grey cement slurry @ 3.3kg/sqm including grouting the joints with white cement and matching pigments etc., complete. Size of Tile 600x600 mm single charge |
| 36 | Providing and laying vitrified floor tiles of specified size (thickness to be specified by the manufacturer) of 1st quality with water absorption less than 0.08% and conforming to IS : 15622, of approved make, in all colours and shades, in skirting, riser of steps, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand), jointing with grey cement slurry @ 3.3kg/sqm including grouting the joints with white cement and matching pigments etc., complete. Size of Tile 600x600 mm single charge |
| 37 | Providing and applying cement based putty (Birla, Jk or equivalent) to the required finish complete in all respect and to the entire satisfaction of Engineer-in-charge. |
| 38 | Repair of deteriorated RCC Balconies, Beams, Walls, Ceiling, Column or other concrete surface having exposed rusted bars consisting of following operations (a) chipping of concrete surface 25mm thick average depth afterwards removal of loose concrete and exposing the steel bars. Cleaning the surface properly to remove dust particles and rust from the steel bars. (b) Moistening the surface properly and applying arcylic polymer (acrocrete/ pidilite/ mastercrete or its equivalent) coating mixed with cement for proper bonding of old and new concrete in two coats 0.2kg per 1kg of cement. (c) Providing and fixing chicken mesh of standard size and 26 guage with steel reinforcement by using binding wire and nails complete. (d) Provding and placing of cement concrete l:11/2:3 having average thickness 1\\" (3/4\\" to 11/4\\" thick) mixed with arcylic polymer admixture @ 1kg per bag of cement and waterproof agent @ 400ml per 2 bags of cement including finishing the surface complete in all respect as per the direction and to the entire satisfaction of Engineer-in-Charge. |
| 39 | Providing and fixing 20 mm thick EPDM rubber tile flooring of size 20\\" x 20\\", manufactured from homogeneous rubber compound, having smooth anti-skid surface with anti-static, anti-fungal and anti-bacterial characteristics, laid and fixed with approved adhesive, complete in all respects as per specifications and directions of Engineer-in-Charge. |
| 40 | Providing and fixing 4mm thick plain glass panes with beading when required over exixting chowkhat or fixed shutter or fixed portion or glazed shutter including the cost of nails, putty etc. complete in all respect to the entire satisfaction of Engineer-in-charge. |
| 41 | Providing and fixing 35mm thick golden champ wood (kiln seasoned) wire guage window shutters consisting of vertical and horizontal styles 75x35mm size with wire mesh 22 x 12 mm gauge fixed with 1/2\\"x3/4\\" golden champ wood (kiln seasoned) beading. The rate further includes the cost of 3\\" hinges, Aluminium tower bolts 4\\", Aluminium handles 1 nos., I-hook and two coats of special quality enamel paint over coat of primer after preparation of surface (special quality) complete in all respect to the entire satisfaction of Engineer-in-charge. |
| 42 | Providing and fixing 35mm thick golden champ wood (kiln seasoned) glazed window shutters consisting of vertical and horizontal styles 75x35mm size with 4mm thick floated glass pane fixed with 1/2\\"x3/4\\" golden champ wood (kiln seasoned) beading. The rate further includes the cost of 2 nos. 3\\" hinges, 2 nos. Aluminium tower bolts 4\\", Aluminium handles 1 nos., I-hook and two coats of special quality enamel paint over coat of primer after preparation of surface (special quality) complete in all respect to the entire satisfaction of Engineer-in-charge. |
| 43 | Providing and fixing factory-made powder-coated galvanized steel door frame of size 80 × 50 mm (Single Rebate), fabricated from roll-formed sections of 1.20 mm thick galvanized steel (Base steel conforming to IS:513) with zinc coating and pure polyester powder coating, having 35 mm rebate for door shutters, complete as per approved sample and direction of Engineer-in-Charge. |
| 44 | Providing and fixing factory-made powder-coated galvanized steel frames of size 72 mm × 55 mm for windows/ventilators, fabricated from roll-formed sections out of 0.58 mm thick galvanized steel sheet (Base steel conforming to IS:513) with zinc coating and pure polyester powder coating, complete as per approved sample and direction of Engineer-in-Charge. |
| 45 | PUBLIC HEALTH: Earth work in excavation by mechanical means (Hydraulic excavator) /manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, lift upto 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m. - All kinds of soil |
| 46 | Excavating trenches of required width for pipes, cables, etc including excavation for sockets, and dressing of sides, ramming of bottoms, depth upto 1.5 m, including getting out the excavated soil, and then returning the soil as required, in layers not exceeding 20 cm in depth, including consolidating each deposited layer by ramming, watering, etc. and disposing of surplus excavated soil as directed, within a lead of 50 m : - All kinds of soil - Pipes, cables etc. exceeding 80 mm dia. but not exceeding 300 mm dia metre |
| 47 | Providing and laying in position cement concrete of specified grade excluding the cost of centring and shuttering - All work upto plinth level : - 1:2:4 (1 Cement : 2 coarse sand (zone-III) : 4 graded stone aggregate 40 mm nominal size) |
| 48 | 1:5:10 (1 cement : 5 coarse sand (zone-III): 10 graded stone aggregate 40 mm nominal size) |
| 49 | Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level in all shapes and size in : - Cement mortar 1:6 (1 cement : 6 coarse sand |
| 50 | Half brick masonry with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in foundations and plinth in : - cement mortar 1:4 (1 cement : 4 coarse sand |
| 51 | Providing and fixing 18 mm thick gang saw cut, mirror polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. complete at all levels. - Granite of any colour and shade - Area of slab over 0.50 sqm |
| 52 | Providing and fixing pressed steel door frames conforming to IS: 4351, manufactured from commercial mild steel sheet of 1.60 mm thickness, including hinges, jamb, lock jamb, bead and if required angle threshold of mild steel angle of section 50x25 mm, or base ties of 1.60 mm, pressed mild steel welded or rigidly fixed together by mechanical means, including M.S. pressed butt hinges 2.5 mm thick with mortar guards, lock strike-plate and shock absorbers as specified and applying a coat of approved steel primer after pre-treatment of the surface as directed by Engineer-in-charge: - Profile B - Fixing with adjustable lugs with split end tail to each jamb |
| 53 | Steel work welded in built up sections/ framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required. - In gratings, frames, guard bar, ladder, railings, brackets, gates and similar works |
| 54 | Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS: 15622, of approved make, in all colours and shades,laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joints with white cement and matching pigments etc., complete. - Size of Tile 600x600 mm |
| 55 | 12 mm cement plaster of mix : - 1:4 (1 cement: 4 coarse sand) |
| 56 | Removing white or colour wash by scrapping and sand papering and preparing the surface smooth including necessary repairs to scratches etc. complete |
| 57 | Distempering with dry distemper of approved brand and manufacture (one or more coats) and of required shade on old work to give an even shade. |
| 58 | Renewing glass panes, with putty and nails wherever necessary including racking out the old putty: - Float glass panes of nominal thickness 4 mm (weight not less than 10kg/sqm) |
| 59 | Demolishing cement concrete manually/ by mechanical means including disposal of material within 50 metres lead as per direction of Engineer - in - charge. - Nominal concrete 1:4:8 or leaner mix (i/c equivalent design mix) |
| 60 | Dismantling doors, windows and clerestory windows (steel or wood) shutter including chowkhats, architrave, holdfasts etc. complete and stacking within 50 metres lead : - Of area 3 sq. metres and below |
| 61 | Dismantling stone slab flooring laid in cement mortar including stacking of serviceable material and disposal of unserviceable material within 50 metres lead. |
| 62 | Disposal of building rubbish / malba / similar unserviceable, dismantled or waste materials by mechanical means, including loading, transporting, unloading to approved municipal dumping ground or as approved by Engineer-in-charge, beyond 50 m initial lead, for all leads including all lifts involved |
| 63 | Demolishing brick work manually/ by mechanical means including stacking of serviceable material and disposal of unserviceable material within 50 metres lead as per direction of Engineer-in-charge - In cement morta |
| 64 | Providing and fixing white vitreous china water closet squatting pan (Indian type) : - Orissa pattern W.C. pan of size 580x440 mm |
| 65 | Providing and fixing soil, waste and vent pipes - 100 mm dia - Centrifugally cast (spun) iron socket & spigot (S&S) pipe as per IS: 3989 |
| 66 | Providing and fixing heel rest sanitary bend - 100 mm dia - Sand cast iron S&S as per IS - 3989 |
| 67 | Providing and fixing collar : - 100 mm - Sand cast iron S&S as per IS - 3989 |
| 68 | Providing and fixing trap of self cleansing design with screwed down or hinged grating with or without vent arm complete, including cost of cutting and making good the walls and floors : - 100 mm inlet and 75 mm outlet - Sand cast iron S&S as per IS - 3989 |
| 69 | Providing and fixing G.I. pipes complete with G.I. fittings and clamps, i/c cutting and making good the walls etc. (EXPOSED) - 20 mm dia nominal bore |
| 70 | 25 mm dia nominal bore |
| 71 | Providing and fixing G.I. Pipes complete with G.I. fittings and clamps, i/c making good the walls etc. concealed pipe, including painting with anti corrosive bitumastic paint, cutting chases and making good the wall : - 15 mm dia nominal bore |
| 72 | 20 mm dia nominal bore |
| 73 | Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) : - 20 mm nominal bore |
| 74 | 25 mm nominal bore |
| 75 | Providing and placing on terrace (at all floor levels) polyethylene water storage tank, IS : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank. |
| 76 | Providing and fixing C.P. Brass extension nipple (size 15mmx50mm) of approved make and quality as per direction of Engineer-in-charge. |
| 77 | Cutting holes up to 30x30 cm in walls including making good the same - With common burnt clay F.P.S. (non modular) brick |
| 78 | Cutting holes up to 15x15 cm in R.C.C. floors and roofs for passing drain pipe etc. and repairing the hole after insertion of drain pipe etc. with cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size), including finishing complete so as to make it leak proof. |
| 79 | Providing and fixing square-mouth S.W. gully trap class SP-1 complete with C.I. grating brick masonry chamber with water tight C.I. cover with frame of 300 x300 mm size (inside) the weight of cover to be not less than 4.50 kg and frame to be not less than 2.70 kg as per standard design: - 100x100 mm size P type - With common burnt clay F.P.S. (non modular) bricks of class designation 7.5 |
| 80 | Making connection of drain or sewer line with existing manhole including breaking into and making good the walls, floors with cement concrete 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) cement plastered on both sides with cement mortar 1:3 (1 cement : 3 coarse sand), finished with a floating coat of neat cement and making necessary channels for the drain etc. complete : - For pipes 100 to 250 mm diameter |
| 81 | Constructing brick masonry chamber for underground C.I. inspection chamber and bends with bricks in cement mortar 1:4 (1 cement : 4 coarse sand) C.I. cover with frame (light duty) 455x610 mm internal dimensions, total weight of cover with frame to be not less than 38 kg (weight of cover 23 kg and weight of frame 15 kg), R.C.C. top slab with 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size), foundation concrete 1:5:10 (1 cement : 5 coarse sand (Zone III) : 10 graded stone aggregate 40 mm nominal size), inside plastering 12 mm thick with cement mortar 1:3 (1 cement : 3 coarse sand), finished smooth with a floating coat of neat cement on walls and bed concrete etc. complete as per standard design: DSR 19.30 - . Inside dimensions 600x 850 mm and 45 cm deep for pipe line with three or more inlets : DSR 19.30.3 DSR19.30.3 - . With common burnt clay F.P.S. (non modular) bricks of class designation 7.5 DSR 19.30.3.1 |
| 82 | Extra for depth beyond 45 cm of brick masonry chamber - For 600x850 mm size - With common burnt clay F.P.S. (non modular) bricks of class designation 7.5 |
| 83 | Providing drip seal joints to sand cast iron/centrifugally cast (spun) iron pipes and fittings of diameter : - 100 mm |
| 84 | Providing and fixing 1st quality/ceramic/vetrified glazed wall tiles conforming to IS:15622 (thickness to be specified by the manufacturer) of approved make of size 600x1200mm (Colour & design as approved by Engineer-in-charge ) in skirting, risers of steps and dados, over 12mm thcik bed of cement mortar 1:3 (1 cement : 3 coarse sand ) and jointing with grey cement slurry @ 3.3kg per sqm including pointing in white cement mixed with pigment of matching shade complete |
| 85 | Construction of curb with CC 1: 2: 4 along with upto 1.00 depth for made it proof water including cost of sand , bajri complete in all respect |
| 86 | Providing and fixing ISI Marked water proof 30 mm thick flush door shutters of pine frame seasoned and treated with seasoned pine filler and 2.5 mm gurjan core, fungus resistant , eco friendly with 1mm thick laminated on both side with phenol formaldehyde resin conforming to IS: 848;complete in all respect of approved make |
| 87 | Dismantling of floor tiles and wall tiles complete in all respect. |
| 88 | Providing and laying of UPVC pipe, IS-4985 marked, Pressure 6 kg/cm2 including cutting, joining, solvent and all necessary fittings complete in all respect except excavation.Size 110mm i/d |
| 89 | Providing and fixing of Wall Hung Seat with in-built jet, UF Soft Close Slim Seat Cover, Hinges and accessories Make Jaquar Model SOLO or equivalent model of other approved makes in the same range of AOR to the satisfaction of EIC. |
| 90 | Providing and fixing of Single Piece Slim Concealed Cistern of approved make complete. |
| 91 | Providing and fixing of Control Plate of approved Make and Model |
| 92 | Providing and fixing of Chinaware Urinal with sensor Make Kerovit Model WALTER Size 300 x 335 x 705 or equivalent model of other approved makes in the same range of AOR to the satisfaction of EIC. |
| 93 | Providing and fixing of Frosted Glass Urinal Partition of size 900 x 450 x 8 mm complete with SS Cleats fixing arrangement in all respects of Make Jaquar Model JSE-CHR-810UC450X or equivalent model of other approved makes in the same range of AOR to the satisfaction of EIC. |
| 94 | Providing and fixing of Chinaware Counter Top Basin of size 600 x 400 x 160 mm Make Kerovit Model MARK, CERA CAFÉ or equivalent model of other approved makes in the same range of AOR to the satisfaction of EIC. |
| 95 | Providing and fixing CP Single Lever Basin Mixer with 450 mm long braided hoses, complete in all respect make Jaquar Model Opal Prime or equivalent model of other approved makes in the same range of AOR to the satisfaction of EIC. |
| 96 | Providing and fixing CP Deck Mounted Sensor Faucet tall body without pop up complete in all respect make Kerovit or equivalent model of other approved makes in the same range of AOR to the satisfaction of EIC. |
| 97 | Providing and fixing of Health Faucet with flexible tube & Wall Hook make Jaquar Model ALD 565 or equivalent model of other approved makes in the same range of AOR to the satisfaction of EIC. - Health Faucet |
| 98 | Providing and fixing of CP Faucets of make Jaquar Model OPP or equivalent model of other approved makes in the same range of AOR to the satisfaction of EIC. - Angular Stop Cock |
| 99 | Concealed Stop Cock ( Concealed & Exposed Part ) |
| 100 | Providing and fixing of CP Faucets of make Jaquar Model Continental Prime or equivalent model of other approved makes in the same range of AOR to the satisfaction of EIC. - Bib Cock |
| 101 | Angular Stop Cock |
| 102 | Providing and fixing of Single Lever 2 Inlet Diverter with provision of Overhead Shower ( Exposed and concealed both parts ) complete of Make Jaquar Model OPP or equivalent model of other approved makes in the same range of AOR to the satisfaction of EIC. |
| 103 | Providing and fixing of Overhead Shower Size 200 x 200 of Make Jaquar Model 35497 or equivalent model of other approved makes in the same range of AOR to the satisfaction of EIC. |
| 104 | Providing and fixing of Shower Arm 600 mm long of Make Jaquar Model 479L or equivalent model of other approved makes in the same range of AOR to the satisfaction of EIC. |
| 105 | Providing and fixing of CP Accessories of make Jaquar Model Continental or equivalent model of other approved makes in the same range of AOR to the satisfaction of EIC. - Toilet Roll Holder with Flap |
| 106 | Towel Ring |
| 107 | Towel Rail |
| 108 | Providing and fixing of Hand Drier with Low Noise up to 70 dB, Air speed 16 m/s, of make Viking Model 58131 with material ABS or equivalent model of any other approved / reputed make to the satisfaction of EIC |
| 109 | Providing and fixing of Lotion Dispenser of following capacity / function of following model of Viking or equivalent model of other approved makes in the same range of AOR to the satisfaction of EIC. - Automatic Lotion Dispenser 700ml Model 1106 |
| 110 | Lotion Dispenser 500 ml ( Model 1127 ) |
| 111 | Providing and fixing SS 304 Braided PVC connection pipe with brass unions Size 600 mm : |
| 112 | Providing and fixing toilet cubical of standard dimension 2025 mm (H) x 1000 mm ( W) x 1500mm ( Depth ) or as per site, including 600 mm wide door made up of thermosetting resign treated high pressure ,self- supporting decorative compact laminates with permanently incorporate anti-bacterial agents during manufacturing . 12mm thick compact board should be Moisture resistant, Impact resistant, termite resistant, Scratch resistant, Weather and climatic shock resistant. Finish of compact laminates should be suede finish which includes door, pilasters and intermediate panels finished with approved texture/shades as per IS2046 and fulfilled the criteria of fire retardant under BS-476/97. The accessories should be of MOC SS 316 as detailed below |
| 113 | SS 316 Door Stopper, U Channel, Round Toprail, Adjustable Foot, Coat Hook with Stopper, Concealed Hinge, Door Knob, Screw, Thumbturn Lockset Wall Plug Make Greenlam / Merino - Providing and fixing of 5mm thick looking glass with bevelled edge with PVC Beeding or Studs complete in all respect |
| 114 | ELECTRICAL WORK: DSR Item No. 1.10 Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit, with modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm. FRLS PVC insulated copper conductor single core cable etc as required. - Group C |
| 115 | DSR item No.1.31 Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 3 pin 5/6 A modular socket outlet and 5/6 A modular switch, connections etc. as required. |
| 116 | DSR item No.1.32 Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 6 pin 5/6 A & 15/16 A modular socket outlet and 15/16 A modular switch, connections etc. as required. |
| 117 | DSR Item No. 1.17 Supplying and drawing following sizes of FRLS PVC insulated copper conductor, single core cable in the existing surface/ recessed steel/ PVC conduit as required. - 3 x 1.5 sq. mm |
| 118 | 3 x 2.5 sq. mm |
| 119 | 3 x 4 sq. mm |
| 120 | DSR Item No.1.21 Supplying and fixing of following sizes of medium class PVC conduit along with accessories in surface/recess including cutting the wall and making good the same in case of recessed conduit as required. - 20 mm |
| 121 | 25 mm |
| 122 | DSR Item No. 1.33 Supplying and fixing 3 pin, 5 amp ceiling rose on the existing junction box/ wooden block including connection etc as required. |
| 123 | DSR item No.1.26 Supplying and fixing modular blanking plate on the existing modular plate & switch box excluding modular plate as required. |
| 124 | DSR item No.1.24 Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required. - 5/6 amps switch |
| 125 | 3 Pin 5/6 A. socket outlet |
| 126 | DSR item No.1.57 Supplying & fixing suitable size GI box with modular plate and cover in front on surface or in recess including providing and fixing 25 A modular socket outlet and 25 A modular SP MCB, \\"C\\" curve including connections, painting etc. as required. |
| 127 | DSR item No.9.2.3Brush Less Direct Current (BLDC) Fan without RemoteSupply, Installation, Testing and Commissioning of ceiling fan with Brush Less Direct Current (BLDC) Motor, class of insulation: B, 3 nos. metal (Aluminium alloy) blades, 30 cm long down rod, 2 nos. canopies, shackle kit, safety rope, copper winding, steel/Al body Power Factor not less than 0.9, Service Value (CM/M/W) minimum as below, 350 RPM (tolerance as per IS : 374-2019), THD (Total Harmonic Distortion) less than 10%, suitable for operation with regulator for speed control and all remaining accessories including safety pin, nut bolts, washers, temperature rise=75 0C (max.), insulation resistance more than 2 mega ohm, suitable for 230 V, 50 Hz, single phase AC supply, Ceiling Fan compliant to IS 374:2019 fan i/c external connections with 1.5 sq.mm FRLS/HFFR, PVC insulated copper conductor single core cable and earthing etc. as required. - 1200mm, service value ≥ 6.0 CM/Min/Watt, air delivery 210 CM/Min (Minimum) |
| 128 | Supply and fixing of 12 modules (200 mm x 150 mm) G.I box suitable for accommodate the following accessories along with modular base and cover plate for modular switches in recess / surface etc as required for Computer Point with 4 Nos. 5/6 Amp. modular switch and 4 Nos. 3 pin 5/6 Amp. modular socket outlet. The job includes the cost of making interconnections with suitable copper wire, painting of box with approved paint and other petty material required to complete the job to the entire satisfaction of Engineer-in-Charge at site. |
| 129 | S/I/T/C of linear suspended luminaire 4 ft. long made up of extruded aluminium with PMMA diffuser for standalone and seamless end to end connectivity. The fitting is to be installed on existing surface with the help of 2 no. suitable length universal suspensions suitable for quick on site adjustment. The fitting should be of Philips / Wipro / Bajaj / Trilux / Jaquar/ Havells/ Crompton/ Panasonic/ LT/ Surya make only. The job includes carriage, erection, making connections with 3x1.5 sq.mm copper wire from adjacent light point, testing and commissioning of the fittings and all the petty material as required to complete the same to the entire satisfaction of Engineer-in-charge.Specification of LED fittings:Wattage of LED fittingsAs per following parametersTotal lumens of the LED fittingsMinimum 4000 lumenOperating voltage140 V to 270 V, AC supply or better.Input frequency50 Hz + 1 HzPower factorMinimum 0.95Luminaire efficacyMinimum 100 lm/wColor rendering indexCRI shall be 80 (minimum)Working/ operating temperature00 to + 450c or betterColor temperature30000K to 40000KElectronic DriverDrive current (LED)As per OEM.S/I/T/C of linear suspended luminaire 4 ft. long made up of extruded aluminium with PMMA diffuser for standalone and seamless end to end connectivity. The fitting is to be installed on existing surface with the help of 2 no. suitable length universal suspensions suitable for quick on site adjustment. The fitting should be of Philips / Wipro / Bajaj / Trilux / Jaquar/ Havells/ Crompton/ Panasonic/ LT/ Surya make only. The job includes carriage, erection, making connections with 3x1.5 sq.mm copper wire from adjacent light point, testing and commissioning of the fittings and all the petty material as required to complete the same to the entire satisfaction of Engineer-in-charge.Specification of LED fittings:Wattage of LED fittingsAs per following parametersTotal lumens of the LED fittingsMinimum 4000 lumenOperating voltage140 V to 270 V, AC supply or better.Input frequency50 Hz + 1 HzPower factorMinimum 0.95Luminaire efficacyMinimum 100 lm/wColor rendering indexCRI shall be 80 (minimum)Working/ operating temperature00 to + 450c or betterColor temperature30000K to 40000KElectronic DriverDrive current (LED)S/I/T/C of linear suspended luminaire 4 ft. long made up of extruded aluminium with PMMA diffuser for standalone and seamless end to end connectivity. The fitting is to be installed on existing surface with the help of 2 no. suitable length universal suspensions suitable for quick on site adjustment. The fitting should be of Philips / Wipro / Bajaj / Trilux / Jaquar/ Havells/ Crompton/ Panasonic/ LT/ Surya make only. The job includes carriage, erection, making connections with 3x1.5 sq.mm copper wire from adjacent light point, testing and commissioning of the fittings and all the petty material as required to complete the same to the entire satisfaction of Engineer-in-charge.Specification of LED fittings:Wattage of LED fittingsAs per following parametersTotal lumens of the LED fittingsMinimum 4000 lumenOperating voltage140 V to 270 V, AC supply or better.Input frequency50 Hz + 1 HzPower factorMinimum 0.95Luminaire efficacyMinimum 100 lm/wColor rendering indexCRI shall be 80 (minimum)Working/ operating temperature00 to + 450c or betterColor temperature30000K to 40000KElectronic DriverDrive current (LED)As per OEM.Operating voltage140 V to 270 V AC supply or betterType of driverConstant current output driverTHDLess than 10%ProtectionShall have under voltage and over voltage protection.Guarantee of LED fittings including LED driver5 years against manufacturing defect.FixtureShould comply with LM 79 test from NABL/UL lab.LED Type/ Make/ ModelPower CREE/ OSRAM/ NICHIA/ Philips LUMILED with life more than 50,000 burning hours @70% lumen maintenance complying with LM 80 test report from the manufacturer.Life of LED50000 burning hours at 70% lumen maintenance |
| 130 | DSR item No.8.2.3LED Down lighter (SMD Type) (System lumen efficacy ≥120 <135lm/Watt)Supplying, installation, Testing & Commissioning of LED Recessed /surface Down lighter (Round / square/ Rectangular) SMD type of following body material with PMMA and prismatic diffuser and construction as per IS : 10322 with driver as per the requirement with Driver efficiency >85%, Operating voltage AC 140-270 Volt, freq 50/60 hz, Operating temp range -5 deg to 40 deg centigrade, internal surge protection of 2.5 KV with Short & Open circuit protection ,THD < 10% , P. F.≥0.95, IP20, CRI >80 , UGR (Unified Glare Rating) < 19, Flicker free (flicker should be below 5 %), life time (LED,Driver & electrical circuitary), life time of minimum 50000 Burning Hours with , 70% of initial Lumen maintained till life ends , CCT 3000°K / 4000°K / 5700°K /6500°K (As per ANSI Bin), SDCM(Standard Deviation Color Matching) <3, Maximum power consumption should not more than the specified rating and Fixture shall be of relevant BIS standard and trade mark certificate ( T.C.). - Manufactures Word Mark/ Name Engraved/ Embossing/ Screen printing on housing. OEM must have its own in house NABL lab setup for all testing facilities for LED fixtures. \\"complete in all respect i/c external connections with 1.5 sq mm FRLS/HFFR, PVC insulated copper conductor single core cable and earthing etc. as required with Minimum 5 year OEM warranty. System lumen efficacy ≥120 <135 lm/Watt output . LM79 & LM80 Test report and all testing required for LED fixtures as per BIS shall be submitted. Shape size and CCT shall be as approved by Engineer-in-Charge as per requirement. (Thermal management: heat sink of aluminium housing such that LED junction temperature shall not rise above 90°C). - Powder coated die cast /Extruded aluminium Body including trim. - 12-15 Watt |
| 131 | DSR item No.2.2 Providing and fixing following rating and breaking capacity and pole MCCB with thermomagnetic release and terminal spreaders in existing cubicle panel board including drilling holes in cubicle panel, making connections, Ics=100% Icu and Operational Voltage 690V etc. as required - 100 A,30KA,FPMCCB |
| 132 | DSR Item No.2.5 Supplying and fixing of following ways surface/ recess mounting, vertical type, 415 V, TPN MCB distribution board of sheet steel, dust protected, duly powder painted, inclusive of 200 A tinned copper bus bar, common neutral link, earth bar, din bar for mounting MCBs (but without MCBs and incomer) as required (Note: Vertical type MCB TPDB is normally used where 3 phase outlets are required). - 12 way (4 + 36), Double door |
| 133 | DSR Item No. 2.4 Supplying and fixing following way, horizontal type three pole and neutral, sheet steel, MCB distribution board, 415 volts, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required (But without MCB/ RCCB/ Isolator). - 6 way (4 + 18), Double door |
| 134 | DSR Item No. 2.10 Supplying and fixing 5 A to 32 A rating, 240/415 V, 10 kA, \\"C\\" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required. - Single pole |
| 135 | DSR item No.15.16 Supplying and laying of following size DWC HDPE pipe ISI marked along with all accessories like socket, bend, couplers etc. conforming to IS 14930, Part II complete with fitting and cutting, jointing etc. direct in ground (75 cm below ground level) including excavation and refilling the trench but excluding sand cushioning and protective covering etc., complete as required. - 63 mm dia (OD-63 mm & ID-51 mm nominal) |
| 136 | DSR Item No.1.14 Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required. - 4 X 10 sq. mm + 2 X 6 sq. mm earth wire |
| 137 | DSR Item No.5.1 Earthing with G.I. earth pipe 4.5 metre long, 40 mm dia including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe etc. (but without charcoal/ coke and salt ) as required. |
| 138 | DSR item No.5.12 Providing and laying earth connection from earth electrode with 6 SWG dia G.I. Wire in 15 mm dia G.I. pipe from earth electrode including connection with G.I. thimble excavation and re-filling as required. |
| 139 | Providing and fixing MCB 4 Pole 63 Amps, 415 volt ‘C’ curve 10 KA breaking capacity in the existing enclosure as per site requirement. The job includes making connection with suitable size with copper wire to the entire satisfaction of Engineer in Charge. The makes of MCB TPN should be LK/ Legrand/ Schneider/ Siemens/ ABB make only. |
| 140 | Providing and fixing MCB 3 Pole 63 Amps, 415 volt ‘C’ curve 10 KA breaking capacity in the existing enclosure as per site requirement. The job includes making connection with suitable size with copper wire to the entire satisfaction of Engineer in Charge. The makes of MCB TPN should be LK/ Legrand/ Schneider/ Siemens/ ABB make only. |
| 141 | Supply and laying of XLPE insulated PVC sheathed Aluminum conductor cable of 1.1 KV grade as per IS 7098 (Part-I) 1988 (amended up to date) of the following sizes to be laid in existing RCC/Hume/DWC/ Metal pipe. The job include the cost of making connections with suitable size of Aluminium Lugs/ thimbles, testing, commissioning etc. as required to complete the job to the entire satisfaction of Engineer In Charge. The cable should be of Polycab/ KEI/ RPG/ Unistar (Universal)/ Havells/ Finolex/ R.R. Kabel make only. - Size 35 Sq.mm 3.5 Core XLPE Al. Arm. Cond. Cable Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Sep 21, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedSep 28, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 6 daysSep 28, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 6 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender