Tender For Construction Of Multipurpose Community Centre Under, Jhmdi, Block-Sisai, District-Gumla
Tender Value
14.93 Lakhs
Estimated cost
Bid Submission
26 Sep 2026
4 days left
EMD
30000
Bank guarantee accepted
Document Fee
2500
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Gumla → Jharkhand
EMD Exemption
Not Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for Construction Of Multipurpose Community Centre Under, Jhmdi, Block-Sisai, District-Gumla
BOQ
| Sl. No. | Item Description |
| 1 | CIVIL WORKS |
| 2 | Earth work in excavation of foundation trenches in ordinary soil (vide classification of soil item -A ) and disposal of excavated earth as obtained to a distance up to 50 M. including all lift , leveling ramming the foundation trenches , removing roots of trees, shrubs all complete as per approved design, building specification and direction of E/I |
| 3 | Extra for earth work in hard soil (vide classification of soil –B) all complete as per specification and direction of E/l. |
| 4 | Filling in foundation trenches and plinth in layers not exceeding 150mm thick well-watered, rammed, fully compacted and fine dressed with earth obtained after cutting within a lead of 50M and lift of 1.5M all complete job as per specification and direction of E/I |
| 5 | Filling in foundation trenches and plinth in layers not exceeding 150mm thick well-watered, rammed, fully compacted and fine dressed with earth obtained after cutting within a lead of 50M and lift of 1.5M all complete job as per specification and direction of E/I |
| 6 | Providing coarse clean sand in filling in foundation trenches or in plinth including ramming and watering in layers not exceeding 150mm thick with all leads and lifts including cost of all materials, labour, royalty and taxes all complete as per building specification and direction of E/l. (Mode of measurement compacted volume) |
| 7 | Providing designation 75A one brick flat soling in foundation, joints filled with local sand including cost of watering, taxes, royalty all complete as per building specification and direction of E/I |
| 8 | Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering. All work up to plinth level 1:3:6 (1 cement: 3 coarse sand (zone-III) : 4 graded stone aggregate 40 mm nominal size) |
| 9 | Providing and laying in position specified grade of reinforced cement concrete excluding the cost of centering, shuttering, finishing and reinforcement - All work up to plinth level 1:1.5:3 (1 cement :1.5 coarse sand (zone-iii) :3 graded stone aggregate 20mm nominal size) |
| 10 | Providing designation 75A brick work in C.M. (1: 6) in foundation and plinth with approved quality of clean coarse sand of F.M. 2 to 2.5 including providing 10mm thick mortar, joints cost of screening materials raking out joints to 15mm depth , curing , taxes and royalty all complete as per building specification and direction of E/I. |
| 11 | Providing and laying damp-proof course 50mm thick with cement concrete 1:2:4 (1 cement: 2 coarse sand(zone-III) : 4 graded stone aggregate 20mm nominal size). |
| 12 | Providing designation 100 A brick work with fly ash lime brick (FLAG) confirming to IS 12894-1990 (9\\"x4.5\\"x3\\") in C.M. (1:6) in foundation and plinth with approved quality of clean coarse sand of F.M. 2 to 2.5 including providing 10mm thick mortar joints, cost of screening materials, raking out joints to 15mm depth, curing, taxes and royalty all complete as per building specification and direction of E/I. |
| 13 | Providing designation 112mm thick reinforcement designation 100 A brick work with fly ash lime brick (FLAG) confirming to IS 12894-1990 (9\\"x4.5\\"x3\\") in C.M. (1:4) in superstructure with approved quality of clean coarse sand of F.M. 2 to 2.5 including cost of screening materials scaffolding raking out joints to 15mm depth curing taxes and royalty ( but excluding theb cost of reinforcement) all complete as per building specification and direction of E/I. |
| 14 | Extra for providing and placing in position 2 Nos 6mm dia. M.S. bars at every third course of half brick masonry. |
| 15 | Reinforcement cement concrete work in beams, suspended floors, roofs having slope up to 15° landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases. above plinth level up to floor five level, excluding the cost of centering, shuttering, finishing and reinforcement - All work up to plinth level 1:1.5:3 (1 cement :1.5 coarse sand (zone-iii) :3 graded stone aggregate 20mm nominal size)GF+FF |
| 16 | Reinforcement cement concrete work in wall (any thickness), including attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers, abutments, posts and struts etc. above plinth level up to floor five level, excluding the cost of centering, shuttering, finishing and reinforcement - All work up to plinth level 1:1.5:3 (1 cement :1.5 coarse sand (zone-iii) :3 graded stone aggregate 20mm nominal size) |
| 17 | providing Tor steel reinforcement of 8mm dia rods as per approved design and drawing exclusive carriage of M.S. bars to work site, cutting, bending and binding with annealed wire with cost of the wire, removal of rust, placing the rods in position all complete as per building specification and direction of E/I. |
| 18 | Providing Tor steel reinforcement of 8mm dia rods as per approved design & drawing (TMT Fe 500 only valid for SAIL & TATA Steel) |
| 19 | Providing Tor steel reinforcement of 10mm dia rods as per approved design & drawing (TMT Fe 500 only valid for SAIL & TATA Steel) |
| 20 | Providing Tor steel reinforcement of 12 to 16 mm dia rods as per approved design & drawing (TMT Fe 500 only valid for SAIL & TATA Steel) |
| 21 | Providing and fixing fan hook of 16mm dia M.S. bar 1 meter long bent to required size and shape placed in position and fixed in R.C.C slab/beam at the time of casting all complete as per building specification and direction of E/l. (where material is not supplied by dept.) |
| 22 | Providing cantering and shuttering including strutting propping etc. and its removal after use in foundation work as per specification and direction of E/I |
| 23 | Foundations, footings, bases for columns, etc for mass concrete |
| 24 | Lintels, beams, plinth beams, girders, bressumers and cantilevers |
| 25 | Suspended floors, roof, landings, balconies and access platform |
| 26 | Columns, pillars, piers, abutment, posts and struts |
| 27 | Weather shade, Chajjas, corbels etc., including edges |
| 28 | Supplying, fitting and fixing collapsible gate of approved size and make properly fabricated with vertical double channels 20 x 10 x 2mm at 100mm centres and braced with M.S. flat diagonals 20 x 3mm with top and bottom rails of T.iron 40 x 40 x 6mm with 38mm dia steel pulleys complete with bolts, nuts, locking arrangement, stoppers, handles, including applying a priming coat of red lead paint, car riage, hoisting and taxes all complete as per building specification and direction of E/I. |
| 29 | Supplying, fitting and fixing MS grill made of 20x6mm MS flat as per approved design and drawing properly fabricated with joints continuous fillet welded and finished smooth, carriage of grill to work site hoisting as per building specification and direction of E/l. (where materials is not supplied by the dept.) |
| 30 | Supplying, fitting and fixing 20 gauge G.C.I. Sheet gate fitted on M.S. Angle frame of size 60X60X6mm. Including cost of fabrication, providing necessary locking arrangement with haskal and domny duly fixed in P.C.C. (1:2:4) blocks of required size applying a priming red lead paint over steel work, taxes all complete as per drawing specification and direction of E/I. |
| 31 | Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / paneling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing, paneling and dash fasteners to be paid for separately) : |
| 32 | For shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber / neoprene gasket required (Fittings shall be paid for separately) |
| 33 | Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-in-charge . (Cost of aluminium snap beading shall be paid in basic item): 21.3.1 With float glass panes of 4.0 mm thickness (weight not less than 10kg/sqm) |
| 34 | Providing and laying 25mm thick kotah stone slab flooring of approved size texure and colour over 19mm thick base of lime mortar (1:1:1) (limeputty:surkhi:coarse sand) laid over and jointed with grey cement slurry mixed with pigment to match the shade of slab including rubbing and polishing to granolithic finish with approved quality of carborandum stone including cost of curing, taxes and royalty all complete as per building specification and direction of E/I. |
| 35 | Providing and laying 25mm thick kotah stone tiles in risers of steps skirting and pillars of approved size texure and colour laid over 12mm thick cement mortar (1;30 and joined with grey cement slurry mixed with pigment to match the shade of the slab including rub bing to granolithic finish with approved quality of carborandum stone including cost of curing, taxes and royalty all complete as per building specification and direction of E/I. |
| 36 | Providing and laying Double charge vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS: 15622 / ISO 13006 of approved make, in all colours and shades, laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joints with white cement and matching pigments etc., complete. Size of Tile 600x600 mm . |
| 37 | Providing 12mm thick cement plaster (1:6) with clean coarse sand of F.M. 1.5 including screening, curing with all leads and lifts of water scaffolding taxes and royalty all complete as per building specification and direction of E/l. |
| 38 | Providing 6mm thick cement plaster (1:4) in ceiling with clean coarse sand of F.M. 1.5 including screening, curing with all leads and lifts of water scaffolding taxes and royalty all complete as per building specification and direction of E/l. |
| 39 | Providing 12mm cement plaster (1:3) with clean coarse sand of F.M. 1.5 including screening, curing with all leads and lifts of water, scaffolding taxes and royalty all complete as per building specification and direction of E/I |
| 40 | Providing and applying white cement-based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete. |
| 41 | Providing two coats of oil bound distemper of approved shade and make over a coat of cement primer over new surface including preparing the plastered surface by the rubbing smooth with pumice stone or fine sand paper applying putty wherever required scaffolding washing of floors and taxes all complete as per building specification and direction of E/I. |
| 42 | Providing and applying white cement-based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete. |
| 43 | Finishing walls with Premium Acrylic Smooth exterior paint with Silicone additives of required shade: New work (Two or more coats applied @ 1.43 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm) |
| 44 | Providing primer one coat of red lead paint of approved make over new steel surface including preparing the surface after cleaning, removing dust, dirt, scales smokes and grease and cleaning the surface thoroughly including cost of scaffolding and taxes all complete as per building specification and direction of E/I. (Mode of measurement area shall be multiplied by the co-efficient as indicated in building specification) |
| 45 | Providing two coats of synthetic enamel paint of approved shade and make over steel surface including cleaning the surface thoroughly specification and taxes all complete as per building specification and direction of E/l. |
| 46 | Making plinth protection 50mm thick of cement concrete 1:3:6 (1 cement :3 coarse sand: 6 graded stone aggregate 20 mm nominal size) over 75mm thick bed of dry brick ballast 40 mm nominal size, well rammed and consolidated and grouted with fine sand including finishing the top smooth |
| 47 | Providing 1.5mm cement punning including curing, carriage of water with all leads and lift as per building specification and direction of E/I. |
| 48 | Diluting and injecting chemical emulsion for POST-CONSTRUCTIONAL anti-termite treatment (excluding the cost of chemical emulsion) : Treatment of soil under existing floors using chemical emulsion @ one litre per hole, 300 mm apart including drilling 12 mm diameter holes and plugging with cement mortar 1 :2 (1 cement : 2 Coarse sand) to match the existing floor: |
| 49 | Carriage of Materials: - |
| 50 | i) Bricks (10 Km) |
| 51 | ii) Sand (lead 10 Km) |
| 52 | iii) Stone Chips lead 30 KM |
| 53 | Add Electrical Work |
| 54 | GST @18% |
| 55 | LABOURCESS @1% Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Sep 21, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedSep 26, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 4 daysSep 28, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 6 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender